Post on 24-Dec-2015
description
transcript
Isotape® Adhesive Tapes for Electrical Insulation
Adhesive Tapes for Electrical Insulation 3
For every application Von Roll offers an appropriate solution. The following tables show our wide selection:
*colors: yellow, red, blue, black, green, white, transparent
Self-Adhesive Products
Insulation class 130°C (B)
Product Backing
Backing thickness (mm)
Total thickness (mm)
Adhesive type Color
Adhesion to steel(N/cm)
Tensile strength(N/cm)
Elongation at break (%)
Breakdownvoltage (V EFF)
Polyester films
Intertape® 51587
Polyester
0.023 0.056 RT black/yellow 5.5 44 100 5000
Intertape® 51588
0.023 0.056 RT clear 5.5 44 100 5000
Intertape® 51594
0.025 0.051 RT yellow 4.9 44 100 5000
Intertape® 54108
0.023 0.060 RT beige 5.5 44 100 5000
Isotape® 50501(1)(2)
0.025 0.055 AT 7 colors* 4.4 36 80 5000
Intertape® 51589
0.025 0.056 A yellow/clear 3.85 44 100 5000
Intertape® 54113
0.023 0.060 A yellow/clear 4.9 44 100 5000
Isotape® 51350 PV3(4)
0.025 0.060 AT FR 7 colors* 4.0 44 100 5000
Isotape® 51350 PV3-2(4)
0.050 0.090 AT FR 7 colors* 3.72 86 100 6500
Polyester laminates
Intertape® 4426
Polyester/ Rope Fiber
0.100 0.165 RT white/black 6.5 80 2 5500
Intertape® 51596
Polyester/ Non-woven
0.090 0.114 RT white/black 6.6 55 60 5000
Polyester reinforced glass filament
Intertape® 51599 PV1
Polyester reinforced glass filament
0.127 0.178 RT beige 6.0 600 5 5000
Glass cloths
Intertape® 4616
Glasscloth
0.130 0.180 RT black/white 5.5 310 3 3000
Intertape® 461FR(1)
0.125 0.180 RT black 4.4 310 3 3000
Insulation class 105°C (A)
Product Backing
Backing thickness mm
Total thickness mm
Adhesive type Colour
Adhesion to steel(N/cm)
Tensile strength(N/cm)
Elongation at break (%)
Breakdownvoltage (V EFF)
Polyester films
Isotape® 4561PV3(4)
Silk acetate 0.180 0.240 RT white/black 3.2 60 15 2000
4 Adhesive Tapes for Electrical Insulation
Product Backing
Backing thickness(mm)
Total thickness(mm)
Adhesive type Color
Adhesion to steel(N/cm)
Tensile strength(N/cm)
Elongationat break (%)
Breakdownvoltage (V EFF)
Speciality
Isotape® 4138 (0)
Polypropylene 0.040 0.065 A clear 3.2 48 100 4000
Intertape® 4564
Polyester fleece
0.061 0.165 AT (z) white 3.6 30 35 500/4600
Intertape® 4560
Silk acetate 0.152 0.180 RT black/white
5 70 15 2000
Isotape® 4560 PV3
Silk acetate 0.180 0.240 RT black/white
5 60 15 2500
Isotape® 51600 PV3 (0)
Polyester cloth 0.125 0.180 AT black/white
10 120 10 1000
*Colors: yellow, red, blue, black, green, white, transparent
Insulation class 155°C (F)
Product Backing
Backing thickness (mm)
Total thickness (mm)
Adhesive type Color
Adhesion to steel(N/cm)
Tensile strength(N/cm)
Elongation at break (%)
Breakdownvoltage (V EFF)
Polyester laminates
Isotape® 51044 PV3 (4)
Polyester/ Non-woven
0.170 0.230 AT white 3.8 55 60 6500
Intertape® 51595
Polyester/ Non-woven
0.090 0.114 A white 5.5 52 30 4500
Polyester reinforced glass filament
Intertape® 4238
Polyesterreinforcedglassfilament
0.165 0.190 AT clear 4.8 657 5 6000
Intertape® 51597
0.140 0.165 AT clear 4.4 438 5 5000
Glass cloths
Isotape® 4627 (2)
Glass cloth
0.130 0.180 RT white 5.5 310 5 3000
Intertape® 4617
0.130 0.180 AT white 4.4 350 3 3000
Isotape® 4637 PV3 (4)
0.125 0.180 AT white 3.4 240 5 2500
Intertape® 54562
0.130 0.210 AT white 4.8 345 5 3000
Speciality
Isotape® 54356 PV3 (4)
Nomex®/ polyester
0.050/ 0.150
0.270 AT FR white 4.32 196 80 8500
Isotape® 56228 PV3 (4)
Nomex® 0.050 0.090 AT white 4.8 32 10 2000
Polyimide films
Intertape® 51579
Polyimide 0.025 0.046 AT amber 3.8 52 60 7000
Adhesive Tapes for Electrical Insulation 5
(0) Tape not UL approved. (1) Passes UL 510 Flame retardancy. (2) Tapes UL approved under their own supplier numbers, available upon request.(z) Zone coated. (4) UL Approved under UL file E315249 or E315208. (R) Natural rubber. (RT) Thermosetting rubber. (A) Acrylic. (AT) Thermosetting acrylic. (AT FR) Thermosetting acrylic Flame Retardant. (Si) Silicone. (SiT) Thermosetting silicone Nomex® and Kapton®
are Trade names of Dupont de Nemours.
Insulation class 180°C (H)
Product Backing
Backing thickness (mm)
Total thickness (mm)
Adhesive type Color
Adhesion to steel(N/cm)
Tensile strength(N/cm)
Elongation at break (%)
Breakdownvoltage (V EFF)
Glass cloths
Isotape® 4638 PV3
Glass cloth 0.120 0.190 Si white 3.75 280 5 2000
Speciality
Isotape® 51202 PV3 (4)
Teflon® 0.050 0.095 Si beige 3.6 40 140 9500
Polyimide films
Intert ape® 4118 (1)
Kapton® 0.025 0.063 SiT amber 2.8 52 60 7000
Isotape® 4428 PV3 (4)
Polyimide 0.025 0.064 Si amber 2.3 49 60 6500
Intertape® 4429 (1)
Polyimide 0.050 0.089 Si amber 2.2 114 60 11000
Insulation class 200°C (C)
Product Backing
Backing thickness (mm)
Total thickness (mm)
Adhesive type Color
Adhesion to steel(N/cm)
Tensile strength(N/cm)
Elongation at break (%)
Breakdownvoltage (V EFF)
Glass cloths
Intertape® 4618 (1)
Glass cloth 0.130 0.180 SiT white 4.4 325 3 3000
We are certified for UL, ISO 9001 and ISO 14001:UL approbation file E 20780 & CSA certifiedLR 94980 for Intertape® products UL approvedE315208 & E315249 for isotape® products marked (4).Not UL approved: Isotape® 4138, 4560PV3, 51600PV3.
Insulation class 155°C (F)
Product Backing
Backing thickness (mm)
Total thickness (mm)
Adhesive type Color
Adhesion to steel(N/cm)
Tensile strength(N/cm)
Elongation at break (%)
Breakdownvoltage (V EFF)
Polyester laminates
Isotape® 51044 PV3 (4)
Polyester/ Non-woven
0.170 0.230 AT white 3.8 55 60 6500
Intertape® 51595
Polyester/ Non-woven
0.090 0.114 A white 5.5 52 30 4500
Polyester reinforced glass filament
Intertape® 4238
Polyesterreinforcedglassfilament
0.165 0.190 AT clear 4.8 657 5 6000
Intertape® 51597
0.140 0.165 AT clear 4.4 438 5 5000
Glass cloths
Isotape® 4627 (2)
Glass cloth
0.130 0.180 RT white 5.5 310 5 3000
Intertape® 4617
0.130 0.180 AT white 4.4 350 3 3000
Isotape® 4637 PV3 (4)
0.125 0.180 AT white 3.4 240 5 2500
Intertape® 54562
0.130 0.210 AT white 4.8 345 5 3000
Speciality
Isotape® 54356 PV3 (4)
Nomex®/ polyester
0.050/ 0.150
0.270 AT FR white 4.32 196 80 8500
Isotape® 56228 PV3 (4)
Nomex® 0.050 0.090 AT white 4.8 32 10 2000
Polyimide films
Intertape® 51579
Polyimide 0.025 0.046 AT amber 3.8 52 60 7000
6 Adhesive Tapes for Electrical Insulation
General Specifications
Adhesive type
AcrylicAcrylic adhesive resists to varnish solvents even if not fully cured. The acrylic offers a high ageing resistance until 155°C in use.
Natural rubber adhesiveNatural rubber adhesive requires lowest tem-perature cure cycle to reach its maximum performance but is limited at 130°C for continu-ous use.
Silicone adhesiveSilicone adhesive is used when extremely high temperature is required and up to 180°C. The heat cycle for this adhesive is higher and longer.
ThermosettingHaving the property to perform in a higher bonding when heated or cured.
Flame retardant The adhesive complies with non burning properties.
Adhesive masses
A AcrylicAT Thermosetting AcrylicAT FR Thermosetting Acrylic Flame Retardant R Natural RubberRT Thermosetting Natural RubberSi SiliconeSiT Thermosetting Silicone
Thermosetting cycles
For thermosetting acrylic andrubber adhesivesat 120°C (250°F): 3 hoursat 130°C (275°F): 2 hoursat 150°C (300°F): 1 hour
For thermosetting silicone adhesivesat 260°C (500°F): 2 hours 24 hours recommended for maximum resistance to solvent
Storage conditionsFor the best shelf life, storage temperature should be between 15°C to 25°C Relative Humidity: 50 % (± 30 %)
Slitting toleranceFilms ± 0,4 mm ( ±1/64”)Cloths ± 0,4 mm ( ±1/64”)Laminates ± 0,4 mm ( ±1/64”)Length > 100 m ± 0,8 mm ( ±1/32”)
Temperature rating
Each adhesive tape is allowed to be used at continuous temperature level as shown in this table: Data are for use at 20 000 hours at the temperature continuously.
Insulation class
Temperature rating
Y 90°C
A 105°C
B 130°C
F 155°C
H 180°C
C 200°C
Adhesive Tapes for Electrical Insulation 7
The Appropriate Solution
Polyimide filmsAn excellent choice for high temperature insulation and processing applications thanks to:
» very high heat resistance (between 120°C and 350° for short periods)
» high dielectric strength
Examples: Intertape® 4118, Isotape® 4428 PV3, Intertape® 4429, Intertape® 51579
Speciality
» The unique characteristics of these tapes make them extremely suitable for high voltage insulation applications.
» Zone coating (4564) allows complete impregnation of the varnish.
» An innovative backing (51600 PV3) provides unique properties to fulfil application requirements of new generations of coils.
Polyester reinforced glass filamentThese tapes are mainly compatible with insulation oil for immersed transformers. An excellent choice for heavy duty bundling insulation thanks to:
» high tensile strength with glass filament
» high dielectric properties from the polyester film
Examples: Intertape® 4238, Intertape® 51597, Intertape® 51599 PV1
Glass cloths
» Flexibility and conformability are key features of this product group.
» High heat resistance and tensile strength of the glass cloth fulfil many electrical insulation application requirements.
Examples: Intertape® 461FR, Intertape® 4616, Intertape® 4617, Intertape® 4618, Isotape® 4627, Isotape® 4637PV3, Isotape® 4638 PV3, Intertape® 54562
Polyester laminatesBoth types of polyester laminates offer unique properties.
» Paper/Polyester offers bulk, stiffness and is hand tearable.
» Polyester/Non-woven offers excellent puncture resistance and conformability.
» Higher temperature performance with acrylic adhesives.
Examples: Intertape® 4426, Isotape® 51044PV3 Intertape® 51595, Intertape® 51596, Isotape® 54354
Polyester films
» Excellent combination of qualities: high insulation properties and high dielectric strength at low thickness (25 μ).
» Acrylic adhesives enhance these films by giving the products good chemical and solvent resistance.
» Some polyester films are UL Flame Retardant.
Examples: Isotape® 50501, Intertape® 51587, Intertape® 51588, Intertape® 51594, Intertape® 54108, Intertape® 54113, Isotape® 51350PV3, Isotape® 51350PV3-2, Intertape® 51589
All
info
rmat
ion
in t
his
doc
umen
t su
bje
ct t
o th
e p
rod
uct
liab
ility
cla
use
as p
ublis
hed
in t
he w
ebsi
te w
ww
.von
roll.
com
und
er le
gal i
nfor
mat
ion.
Von Roll is the sole full-range supplier of materials and systems for the insulation of electrical machines as well as high-performance products for various high-tech industries.
We Enable Energy
About Von RollAs one of the longest established industrial companies in Switzerland, founded in 1803, we focus on products and systems for power generation, transmission and distribution, rotating machines and mechanical engineering. Von Roll is the global market leader in insulation products, systems and services and is represented at more than 32 locations in 19 countries with around 3,400 employees.
Please contact us or visit our website www.vonroll.com for further information:
Europe, Middle East, Africa
Von Roll Holding AGSteinacherstrasse 1018804 Au ZHSchweiz/SwitzerlandP +41 44 204 3500F +41 44 204 3010
Asia/Pacific
Von Roll Asia Pte Ltd.Blk 6 Serangoon North Avenue 5Singapore 554910SingaporeP +65 6556 4788 F +65 6556 4959
Americas
Von Roll USA, Inc.200 Von Roll DriveSchenectadyNY 12306USAP +1 518-344-7100 F +1 518-344-7288
MicaMaterials related to high-voltage insulation. Von Roll’s commitment is extensive including all the steps in the manufacturing process.
WiresInsulated round, flat and Litz wires for high-voltage, low-voltage and electronic applications.
CablesMica tapes for fire-resistant cables. Von Roll provides a wide range of products that are ideally suited to all commonly used standards.
LiquidsImpregnation resins for high and low voltage, potting resins, casting resins, as well as encapsulating and conformal coatings.
CompositesEngineered materials made from a resin and a support structure with distinct physical, thermal and electrical properties. They can be molded, machined or semi-finished.
FlexiblesInsulating flexible materials for low-voltage applications such as flexible laminates and adhesive tapes.
TransformersHigh-perfomance transformers for power transmission and distribution, tailored solutions to all applications of today’s energy supply companies.
TestingVon Roll provides electrical, thermal and mechanical testing of individual materials as well as complete insulating systems. We are UL-certified.
TrainingVon Roll Corporate University provides a training program in high- and low-voltage insulation to its customers.