Post on 02-Mar-2018
transcript
7/26/2019 Kobelco Stainless Steel
1/32
flux cored wiresfor easy and high efficiencywelding of stainless steel
7/26/2019 Kobelco Stainless Steel
2/32
2
7/26/2019 Kobelco Stainless Steel
3/32
Ko b e S t e e l , L t d . ______________________________________________________________________________________________________________________________________________________5
Corporate profile Unternehmensprofil Le profil du Groupe
Ko b e l c o W e l d i ng o f E uro p e B . V . ___________________________________________________________________________________________________________7
Introduction Einleitung Introduction
I n t ro d u c t i o n o f Ko b e l c o F l u x Co r e d W i r e s _________________________________________________________________________9 E i n l e i t ung d e s Ko b e l c o F l l d r h t e I n t ro d u c t i o n d e s f i l s f o urr s Ko b e l c o
W e l d i ng w i t h Ko b e l c o F l u x Co r e d W i r e s ______________________________________________________________________________10 S c hwe i e n m i t Ko b e l c o F l l d r h t e n So ud e r a v e c d e s f i l s f o urr s Ko b e l c o
P r o d u c t s __________________________________________________________________________________________________________________________________________________________________ 12
F e rr i t e D i a g r a ms _______________________________________________________________________________________________________________________________________________24
W e l d i n g p o s i t i o n s ___________________________________________________________________________________________________________________________________________ 25
E N 1 2 0 7 3 : 1 9 9 9 _________________________________________________________________________________________________________________________________________________ 26
A W S A 5 . 2 2 - 1 9 9 5 ______________________________________________________________________________________________________________________________________________ 28
L i s t o f a d d r e s s e s ____________________________________________________________________________________________________________________________________________30
3
Contents
7/26/2019 Kobelco Stainless Steel
4/32
4
7/26/2019 Kobelco Stainless Steel
5/32
Cor p or a t e p r o f i l e
Kobe Steel,Ltd. is a diversified corporation with head offices in Tokyo and
Kobe. It is a leading producer of ferrous and nonferrous metal products,
welding consumables, industrial and construction machinery. It also
supplies comprehensive engineering services. The company is diversifying
into new businesses, including information and electronics, factoryautomation and robotics, and advanced materials. Kobe Steel,Ltd. is
becoming a global enterprise engaged in a wide range of activities in
North America, Europe and Asia. The companys strategy of
diversification and globalization is supported by its tripolar R&D network,
which links researchers in Japan, the United States and Europe. Kobelco
is the corporate mark used by Kobe Steel,Ltd., on a variety of products
and is found in the names of a number of subsidiaries. Behind the
Kobelco mark is the companys commitment to excellence and quality.
U n t e r n e h m e n s p r o f i l
Die Kobe Steel,Ltd. ist eine diversifizierte Kapitalgesellschaft, deren
Hauptsitze sich in Tokio und Kobe befinden. Das Unternehmen ist fhrend
bei der Herstellung von Eisen- und NE-Produkten, Schweizusatz-
werkstoffe, Industrie- und Baumaschinen. Es bietet darber hinaus
umfassende Ingenieursdienste an. Das Unternehmen diversifiziert sich in
neue Geschftsbereiche, einschlielich der Informationstechnik,
Elektronik, Fabrikautomatisierung und Robotik sowie moderner Werk-
stoffe. Kobe Steel,Ltd. ist ein globales Unternehmen, das in zahlreichen
Bereichen in Nordamerika, Europa und Asien ttig ist. Die
Diversifizierungs- und Globalisierungsstrategie des Unternehmens wird
durch sein tripolares Forschungs- und Entwicklungsnetz untersttzt, dasForscher in Japan, den USA und Europa miteinander verbindet. Kobelco ist
ein Firmenzeichen von Kobe Steel,Ltd., das fr eine Vielzahl von
Produkten verwendet wird und integraler Bestandteil des Firmennamens
einiger Tochterfirmen ist. Kobelco steht fr die Selbstverpflichtung des
Unternehmens zu Brillanz und Qualitt.
L e p r o f i l d u G r o u p e
Kobe Steel,Ltd. Est un groupe diversifl, qui a tabli ses quartiersgnraux Tokyo et Kobe. Cest un producteur mondial de produits
mtalliques ferreux et non-ferreux, de consommables de soudage, de
machines pour lindustrie et la constructione. Il fournit galement des
services des services tendus de gnie civil. La socit se lance dans de
nouvelles voies, inclus linformation et llectronique, lautomatisation
dusines, la robotique et les matriaux de pointe. Kobe Steel,Ltd. Devient
une entreprise globale, engage dans une large gamme dactivits en
Amerique du Nord, lEurope et lAsie. Cette stratgie de diversification et
de globalisation est soutenue par son rseau tripolaire de recherche et de
dveloppement, qui relei des chercheurs du Japon, aux Etats-Unis et en
Europe. Kobe Steel,Ltd. utilize le nom commercial Kobelco pour une
grande varit de produits. Ce nom est galement repris dans la
dnomination de plusieurs filiales. La marque Kobelco signifie
lengagement de la socit en ce qui concerne perfection et qualit.
5
KobeS
teel,Ltd.
7/26/2019 Kobelco Stainless Steel
6/32
6
7/26/2019 Kobelco Stainless Steel
7/32
7
I n t r o d u c t i o n
Kobelco Welding of Europe B.V. (KWE) is a modern manufacturer of flux cored wire (FCW) which was
established in 1994 under license from Kobe Steel,Ltd. Benefiting from Kobe Steel,Ltd.s almost 60
years of expertise in welding consumables, Kobelco Welding of Europe B.V. has established itself as
a leading producer of flux cored wire for stainless steel. The factory started production in the
autumn of 1995. The wide range of welding consumables covers almost the entire market for
stainless steel. For welding mild steel we provide a large range of wires imported from Kobe
Steel,Ltd. Japan.
Kobelco wires are used for welding operations all over the world. Industries such as shipbuilding,
offshore, construction and many other industrial sectors rely on Kobelco wires.
E i n l e i t u n g
Kobelco Welding of Europe B.V. (KWE) ist ein modernes Unternehmen, das Flldrhte herstellt und
1994 von Kobe Steel,Ltd. gegrndet wurde. Dank der beinahe 60-jhrigen Erfahrung von Kobe
Steel,Ltd. auf dem Gebiet der Schweizusatzwerkstoffe hat sich Kobelco Welding of Europe B.V. zu
einem der fhrenden Hersteller von Flldrhten fr rostfreie Sthle entwickelt. Das Werk begann
im Herbst 1995 mit der Produktion. Das breit gefcherte Angebot an Schweizusatz-werkstoffen
deckt fast den gesamten Markt fr rostfreie Sthle ab. Fr unlegierten Stahl liefern wir ebenfalls
ein breites Drahtsortiment, das wir direkt von Kobe Steel,Ltd. aus Japan importieren.
Kobelco - Drhte werden weltweit beim Schweien eingesetzt. Industriezweige wie der Schiffsbau,
die Offshore-Industrie, die Bauindustrie und viele andere industrielle Sektoren vertrauen auf
Kobelco-Drhte.
I n t r o d u c t i o n
Kobelco Welding of Europe B.V. (KWE) est un producteur moderne de fils fourrs (FCW), cr en
1994 sous licence de Kobe Steel,Ltd. Japon. Profitant des 60 annes d'exprience en consommables
de soudage de Kobe Steel,Ltd., Kobelco Welding of Europe B.V. est devenu un producteur important
de fils fourrs pour aciers inoxydables. Lusine a dmarr la production en automne 1995. La gamme
tendue de consommables de soudage couvre pratiquement le march entier de lacier inoxydable.
En ce qui concerne le soudage d'acier doux, nous disposons d'une large gamme de fils imports de
Kobe Steel,Ltd. Japon.
Les fils Kobelco sont utiliss pour des travaux de soudage partout dans le monde. Des industries
comme les chantiers navals, loffshore, la construction et beaucoup dautres secteurs industriels
font confiance aux fils Kobelco.Kobelco
Weldin
gofEurope
B.V.
7/26/2019 Kobelco Stainless Steel
8/32
8
7/26/2019 Kobelco Stainless Steel
9/32
9
I n t r o d u c t i o n o f K o b e lc o F l u x C o r e d W i r e s
Metal fabricators face the increasingly difficult challenge of decreasing costs while improving
product quality, productivity and workers environment. In addition, high labour force turnover and
lower skill levels are dictating a need for welding processes and consumables that are easy to use
and require less operator training.The consumption of flux cored wires (tubular wires) is increasing every year due to their excellent
performance and the economical advantages of these wires. Requirements for an increased welded
joint quality and productivity pave way for a wide application of flux cored wires.
The gas shielded Flux Cored Arc Welding (FCAW) process using Kobelco flux cored wire has the
potential to meet current needs and is flexible enough to meet even more demanding requirements
in the future. This is due to more than 30 years of research and development of flux cored wires.
Kobelco flux cored wires come in many different types in response to market requirements. Their
main characteristics of superior operability and high deposition are well known in the welding
industry. They make a great contribution to the reduction of the total cost of welding and the
improvement of the working environment for the welder.
E i n l e i t u n g d e s K o b e lc o F l l d r h t e
Die Metallindustrie wird zunehmend mit dem Problem konfrontiert, die Kosten senken zu mssen
und gleichzeitig die Produktqualitt und die Arbeitsbedingungen verbessern sowie die Produktivitt
steigern zu mssen. Zustzlich zwingen die hohe Fluktuation und schlechtere Ausbildung der
Arbeitskrfte zu Schweiprozessen und Schweizusatzwerkstoffe, die leicht in der Handhabung sind
und weniger Training erfordern. Der Verbrauch an Flldrhten (Rhrendrhte) steigt von Jahr zu Jahr
aufgrund ihrer hervorragenden Eigenschaften und der wirtschaftlichen Vorteile dieser Drhte.
Anforderungen an die gestiegene Qualitt der Schweinhte und die Produktivitt ebnen den Weg
fr eine breite Anwendung von Flldrhten.
Das Schutzgas-Lichtbogen-schweien mit Kobelco-Flldraht wird den heutigen Anforderungen
gerecht und ist flexibel genug, um sogar knftigen Anforderungen zu gengen. Dies ist das Ergebnis
von ber 30 Jahren Forschung und Entwicklung im Bereich der Flldrhte.Kobelco-Flldrhte sind in vielen Varianten erhltlich, die auf die speziellen Bedrfnisse des
Marktes abgestimmt sind. Ihre Hauptmerkmale sind der Schweiindustrie wohlbekannt: berlegene
Funktionalitt und hohe Verfgbarkeit. Sie leisten einen groen Beitrag zur Senkung der
Gesamtschweikosten und verbessern das Arbeitsklima des Schweiers.
I n t r odu c t i o n d e s f i l s f o u r r s K ob e l c o
La fabrication mtallique doit faire face au dfi difficile et croissant de diminuer les cots en
amliorant la qualit du produit, la productivit et lenvironnement des travailleurs. De plus, la
grande mutation des travailleurs et les niveaux de comptence plus faibles dictent un besoin de
procds de soudage et de consommables, qui sont faciles utiliser et qui exigent moinsdentranement de la part de loprateur.
La consommation de fils fourrs (fils tubulaires) augmente chaque anne grce aux performances
excellentes et aux avantages conomiques de ces fils. Des demandes pour une plus grande qualit
du joint et de productivit ouvrent la voie une plus grande application des fils fourrs.
Le procd de soudage fil fourr avec protection gazeuse (FCAW), utilisant le fil fourr Kobelco,
peut satisfaire aux besoins courants et est assez flexible pour rpondre dans le futur des
exigences plus sevres. Ceci est d plus de 30 annes de recherche et de dveloppement des fils
fourrs.
Les fils fourrs Kobelco rpondent par beaucoup de types diffrents aux besoins du march. Leurs
principales caractristiques (maniabilit et haut rendement) sont bien connues dans lindustrie du
soudage. Ils contribuent la rduction du cot total de soudage et lamlioration de
lenvironnement de travail pour le soudeur.
7/26/2019 Kobelco Stainless Steel
10/32
10
W e l d i n g w i t h K o b e l co F l u x C o r e d W i r e s
Before welding, the shielding gas to be applied, parameters and welding method must be
determined.
Shielding gasesThe proper gas composition is important for the bead appearance, weldability and the mechanical
properties of the weld metal.
Welding parameters
Welding current and voltage influence the arc stability, bead appearance, penetration, spatter, etc.
A proper welding current depends on type and size of wire and welding position. Welding speed
and stick-out should also be adjusted for optimum results.
Welding technique and torch angle
For welding stainless steel FCW, backhand welding achieves best results.
S c h w e i e n m i t K o b e lc o F l l d r h t e n
Vor dem Beginn der Schweiarbeiten mssen das zu verwendende Schutzgas, die Parameter und
das Schweiverfahren festgelegt werden.
Schutzgase
Die richtige Zusammensetzung des Gases ist von groer Bedeutung fr das Aussehen der
Schweiraupe, der Schweibarkeit sowie der mechanischen Eigenschaften des Schweigutes.
Schweiparameter
Die Schweistromstrke und Schweispannung beeinflussen die Lichtbogenstabilitt, das Aussehen
der Schweiraupe, den Einbrand, die Spritzer usw. Die passende Schweistromstrke hngt von der
Art und Gre des Drahts und der Schweiposition ab. Die Schweigeschwindigkeit und freiesDrahtende sollten auch richtig eingestellt werden.
Schweitechniken und Brennerwinkel
Beim Schweien hochlegierter Flldrhte lassen sich die besten Ergebnisse mit
Rckhandschweiung (RH) erzielen.
Sou d er a v e c d e s f i l s f o u r r s K ob e l c o
Avant de commencer le soudage, il faut dterminer le gaz de protection, les paramtres et la
mthode de soudage.
Gaz de protection
Le gaz de protection appropri est important pour l'aspect du cordon, la soudabilit et les
proprits mcaniques du mtal dpos.
Paramtres de soudage
Le courant et la tension influencent la stabilit de larc, laspect du cordon, la pntration, les
projections, etc. Le courant de soudage appropri dpend du type et du diamtre du fil et de la
position de soudage. La vitesse de soudage et le stick-out rgissent la pntration et laspect du
cordon.
Technique de soudage et angle de la torche
En ce qui concerne le soudage des fils fourrs inoxydables, le soudage en tirant donne les meilleurs
rsultats.
7/26/2019 Kobelco Stainless Steel
11/32
11
10 - 20o
10 - 20o
Recommended Parameter Range, for flat position Empfohlener Parameterbereich fr die Normalposition Paramtres conseills pour soudage plat
Forehand weldingVH-Schweien Soudage en poussant
The effect of wire stick-out (Wire Extension) on deposition rate Der Einflu unterschiedlich langer freier Drahtende auf der Auftragsleistung Leffef du stick-out sur le taux de dpt
Backhand welding RH-Schweien Soudage en tirant
50 100 150 200 250 300 350 400 450 Amp.
1820
222426
283032
343638
40Volt
1.2 mm
(20mm)
0.9mm
(15mm)
1.6 mm
(25mm)
Note: The above parameter ranges are intendedfor Ar+CO2. More voltage is necessary for 100 % CO2.
Hinweis: Die oben gezeigten Parameterbereichegelten fr Ar+CO2. Bei reinem CO2ist eine hhereSpannung erforderlich.
Note: ces paramtres sont conseills pour Ar+CO2.Il faut plus de tension pour 100% CO2.
KOBE DW-308L KOBE DW-309L KOBE DW-316L
Wire Extension
Freies Drahtende Extension du Fil
( ) =
150 200 250 Amp.
0
1
2
3
4
5
6
7
8
9
10
11
Kg/hr
1.2 mm
25 mm
15 mm20 mm
KOBE DW-316L
7/26/2019 Kobelco Stainless Steel
12/32
12
A p p l i c at i o nKOBE DW-308L and KOBE
DW-308LP are both for
welding low carbon
18% Cr - 8% Ni stainless
steel; both wires have a
nice stable arc, low spatter
generation and are very
user friendly.
For general use
For positional welding
KOBE DW-308L
KOBE DW-308LP
A n w e n d u n gKOBE DW-308L und KOBE
DW-308LP eignen sich zum
Schweien von kohlen-
stoffarmem 18%Cr - 8%Ni
hochlegiertem Stahl; beide
Drhte haben einen sehr
stabilen Lichtbogen, eine
sehr geringe Spritzerbildung
und sind sehr anwender-
freundlich.
Fr allgemeine Aufgaben
Fr alle Positionen
A p p l i c a t i o nKOBE DW-308L et KOBE
DW-308LP pour le soudage
dacier inoxydable faible
teneur en carbone 18% Cr -
8% Ni; les deux fils fourrs
possdent une bonne
stabilit darc, peu de
projections et sont faciles
lemploi.
Pour utilisation gnrale
Pour soudage en position
KOBE DW-308L
80% Ar - 20% CO2 / 100% CO2EN 12073 T 19 9 L R C/M 3
AWS A5.22 E308LT0-1/-4
Wst. Nr. 1.4316
KOBE DW-308LP
80% Ar - 20% CO2 / 100% CO2EN 12073 T 19 9 L P C/M 1
AWS A5.22 E308LT1-1/-4
Wst. Nr. 1.4316
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
KOBE DW-308L 410 570 40 45 -20
KOBE DW-308LP 410 580 41 50 -20
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-308L
KOBE DW-308LP
Polarity (mm)
KOBE DW-308L = / + 0.9 1.2 1.6
KOBE DW-308LP = / + 1.2
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-308L 0.02 0.6 1.6 0.020 0.005 10.1 19.7 - - - 8.9 12.4 10.8
KOBE DW-308LP 0.03 0.7 1.7 0.019 0.004 9.9 19.5 - - - 9.0 12.5 10.3
Chemical Analysis Chemische Analyse Analyse Chimique
7/26/2019 Kobelco Stainless Steel
13/32
13
A p p l i c at i o nKOBE DW-309L and KOBE
DW-309LP are for welding
low carbon 24% Cr 13% Ni
stainless steels and also
dissimilar welding of
stainless steels to carbon or
low-alloy steels. Both wires
have a nice stable arc, low
spatter generation and are
very user friendly.
For general use
For positional welding
KOBE DW-309L
KOBE DW-309LP
A n w e n d u n gKOBE DW-309L und KOBE
DW-309LP eignen sich fr
kohlenstoffarme 24%Cr
13%Ni hochlegierte Sthle,
sowie fr Austenit-Ferrit-
Verbindungen. Beide Drhte
haben einen stabilen
Lichtbogen, eine sehr
geringe Spritzerbildung und
sind sehr anwender-
freundlich.
Fr allgemeine Aufgaben
Fr alle Positionen
A p p l i c a t i o nKOBE DW-309L, KOBE DW-
309LP pour le soudage
dacier inoxydable faible
teneur en carbone 24% Cr
13% Ni; les deux fils fourrs
possdent une bonne
stabilit darc, peu de
projections et sont faciles
lemploi.
Pour utilisation gnrale
Pour soudage en position
KOBE DW-309L
80% Ar - 20% CO2 / 100% CO2EN 12073 T 23 12 L R C/M 3
AWS A5.22 E309LT0-1/-4
Wst. Nr. 1.4332
KOBE DW-309LP
80% Ar - 20% CO2 / 100% CO2EN 12073 T 23 12 L P C/M 1
AWS A5.22 E309LT1-1/-4
Wst. Nr. 1.4332
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-309L 0.02 0.7 1.40 0.019 0.005 12.6 23.9 - - - 13.2 >18.0 19.9
KOBE DW-309LP 0.03 0.7 1.30 0.018 0.005 12.6 23.3 - - - 11.6 >18.0 16.5
Chemical Analysis Chemische Analyse Analyse Chimique
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
KOBE DW-309L 450 580 35 43 -20
KOBE DW-309LP 440 560 38 50 -20
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-309L
KOBE DW-309LP
Polarity (mm)
KOBE DW-309L = / + 0.9 1.2 1.6
KOBE DW-309LP = / + 1.2
7/26/2019 Kobelco Stainless Steel
14/32
14
A p p l i c at i o nKOBE DW-316L and KOBE
DW-316LP are wires for
welding low carbon 18% Cr
- 12% Ni - 2% Mo stainless
steel; both wires have a
nice stable arc, low spatter
generation and are very
user friendly.
For general use
For positional welding
KOBE DW-316L
KOBE DW-316LP
A n w e n d u n gKOBE DW-316L und KOBE
DW-316LP eignen sich fr
kohlenstoffarme 18% Cr
12% Ni 2% Mo
hochlegierte Sthle; beide
Drhte haben einen sehr
stabilen Lichtbogen, eine
sehr geringe Spritzerbildung
und sind sehr anwender-
freundlich.
Fr allgemeine Aufgaben
Fr alle Positionen
A p p l i c a t i o nKOBE DW-316L et KOBE DW-
316LP pour le soudage
dacier faible teneur en
carbone 18% Cr 12% Ni
2% Mo inox; les deux fils
fourrs possdent un arc
stable et jeu de projections,
agrable lusage.
Pour utilisation gnrale
Pour soudage en position
KOBE DW-316L
80% Ar20% CO2 / 100% CO2EN 12073 T 19 12 3 L R C/M 3
AWS A5.22 E316LT0-1/-4
Wst. Nr. 1.4430
KOBE DW-316LP
80% Ar20% CO2 / 100% CO2EN 12073 T 19 12 3 L P C/M 1
AWS A5.22 E316LT1-1/-4
Wst. Nr. 1.4430
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-316L 0.03 0.6 1.6 0.020 0.006 12.2 18.7 2.80 - - 7.7 12.8 9.7
KOBE DW-316LP 0.03 0.7 1.4 0.019 0.006 12.3 18.4 2.90 - - 7.0 11.5 7.8
Chemical Analysis Chemische Analyse Analyse Chimique
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
KOBE DW-316L 430 570 39 44 -20
KOBE DW-316LP 430 570 40 46 -20
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-316L
KOBE DW-316LP
Polarity (mm)
KOBE DW-316L = / + 0.9 1.2 1.6
KOBE DW-316LP = / + 1.2
7/26/2019 Kobelco Stainless Steel
15/32
A p p l i c at i o nKOBE DW-329A and KOBE
DW-329AP are wires for
welding duplex stainless
steels (austenitic-ferretic
stainless steels). These
wires produce weld metal
which is highly resistant to
stress corrosion cracking
and pitting corrosion in
chloride containing
environments. These wires
are widely used in the
chemical, offshore and
shipbuilding industry.
For general use
For positional welding
KOBE DW-329A
KOBE DW-329AP
A n w e n d u n gKOBE DW-329A und KOBE
DW-329AP eignen sich fr
Verbindungsschweien von
Duplex-Sthlen (Werkst.-Nr.
1.4462). Das Schweigut
weist eine hohe Resistenz
gegen Spannungsriss-
korrosion auf. Beide Drhte
lassen sich daher vielseitig
einsetzen; vorrangige
Einsatzgebiete sind in der
Chemieindustrie, im
Offshorebereich und im
Schiffsbau zu finden.
Fr allgemeine Aufgaben
Fr alle Positionen
A p p l i c a t i o nKOBE DW-329A et KOBE DW-
329AP, conus pour le
soudage des aciers
inoxydables duplex (aciers
inoxydables austnitiques-
ferritiques). Ce fil produit un
mtal dpos qui rsiste trs
bien la corrosion sous
tensions ou aux piqures en
prsence de chlorures. Ce fil
est largement utilis dans
lindustrie chimique, loffshore
et les chantiers navals.
Pour utilisation gnrale
Pour soudage en position
KOBE DW-329A
80% Ar20% CO2EN 12073 T 22 9 3 N L R M 3
AWS A5.22 E2209T0-4
Wst. Nr. 1.4462
KOBE DW-329AP
80% Ar20% CO2EN 12073 T 22 9 3 N L P M 1
AWS A5.22 E2209T1-4
Wst. Nr. 1.4462
15
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-329A 0.03 0.58 0.90 0.018 0.007 9.4 23.0 3.5 0.14 - - - 46.0
KOBE DW-329AP 0.03 0.58 0.78 0.019 0.008 9.4 22.9 3.5 0.15 - - - 42.7
Chemical Analysis Chemische Analyse Analyse Chimique
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
KOBE DW-329A 660 840 28 43 -20
KOBE DW-329AP 670 850 29 45 -20
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-329A
KOBE DW-329AP
Polarity (mm)
KOBE DW-329A = / + 1.2
KOBE DW-329AP = / + 1.2
7/26/2019 Kobelco Stainless Steel
16/32
16
A p p l i c at i o nFor welding of stainless
steels to carbon or low-
alloy steels. These wires are
especially suited for buffer
layers, prior to cladding and
overlay welding with Mo
containing stainless steels
such as 316 or 317L.
For general use
For positional welding
KOBE DW-309MoL
KOBE DW-309MoLP
A n w e n d u n gFr das Verbindungs-
schweien von hochle-
gierten mit unlegierten
sowie niedriglegierten
Sthlen. Insbesondere
eignen sich diese Drhte fr
die ersten Pufferlagen vor
dem Auftragsschweien mit
Mo-haltigen Edelsthlen wie
z. B. 1.4401 oder 1.4438.
Fr allgemeine aufgaben
Fr alle Positionen
A p p l i c a t i o nPour la junction des aciers
inoxydables avec les aciers
an carbone. Les fils sont
particulirement biens
adaples au soudage de
pouches - tampon avant le
cladage de ou le soudage de
nechengouva daciers
eoutenant du Mo tels que le
316 ou le 317L.
Pour utilisation gnrale
Pour soudage en position
KOBE DW-309MoL
80% Ar - 20% CO2 / 100% CO2EN 12073 T 23 12 2 L R C/M 3
AWS A5.22 E309LMoT0-1/-4
Wst. Nr. 1.4459
KOBE DW-309MoLP
80% Ar - 20% CO2 / 100% CO2EN 12073 T 23 12 2 L P C/M 1
AWS A5.22 E309LMoT1-1/-4
Wst. Nr. 1.4459
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-309MoL 0.02 0.7 1.4 0.018 0.007 12.7 23.2 2.3 - - 16.8 >18.0 27.0
KOBE DW-309MoLP 0.03 0.6 0.9 0.018 0.006 12.5 22.5 2.3 - - 16.6 >18.0 24.4
Chemical Analysis Chemische Analyse Analyse Chimique
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
KOBE DW-309MoL 540 700 30 42 -20
KOBE DW-309MoLP 530 690 31 48 -20
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-309MoL
KOBE DW-309MoLP
Polarity (mm)
KOBE DW-309MoL = / + 1.2 1.6
KOBE DW-309MoLP = / + 1.2 1.6
7/26/2019 Kobelco Stainless Steel
17/32
17
A p p l i c at i o nDW-310 is suitable for the
welding of heat resistant
CrNi steels.
KOBE DW-312 has a high
resistance to hot cracking
and is suitable for dissimilar
joints, buffer layers and
welding difficult-to-weld
steels.
For general use
For joints sensitive to
cracking
DW-310
KOBE DW-312
A n w e n d u n gDW-310 eignet sich fr
Verbindungen an
hitzebestndigen Chrom -
Nickelsthlen.
KOBE DW-312 hat ein hohe
Warmrisssicherheit und ist
geeignet fr Anwendungen
an Austenit-Ferritver-
bindungen, Pufferlagen und
Verbindungen von
schweikritischen Sthlen.
Fr allgemeine Aufgaben
Fr riempfindliche
Schweiverbindungen
A p p l i c a t i o nDW-310 est destin au
soudage des aciers
rfractaires au CrNi.
KOBE DW-312 possde une
grande rsistance la
fissuration chaud et est
conseill pour les joints
dissemblables, les couches
tampons et l'assemblage
des aciers difficilement
soudables.
Pour utilisation gnrale
Pour Joints sensible la
fissuration
DW-310
80% Ar - 20% CO2 / 100% CO2EN 12073 T 25 20 R C/M1
AWS A5.22 E310T0-1/-4
Wst. Nr. 1.4842
KOBE DW-312
80% Ar - 20% CO2EN 12073 T 29 9 R M 3
AWS A5.22 E312T0-4
Wst. Nr. 1.4337
C Si Mn P S Ni Cr Mo Cu N FS FN FNW
DW-310 0.18 0.6 2.1 0.016 0.005 20.4 25.5 - - - - - -
KOBE DW-312 0.12 0.6 1.2 0.018 0.006 10.2 28.4 - - - 60 >18.0 50.7
Chemical Analysis Chemische Analyse Analyse Chimique
Welding Positions Schweipositionen Positions de Soudage
DW-310
KOBE DW-312
Polarity (mm)
DW-310 = / + 1.2
KOBE DW-312 = / + 1.2
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
DW-310 420 620 33 68 0
KOBE DW-312 580 740 23 - -
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
7/26/2019 Kobelco Stainless Steel
18/32
18
A p p l i c at i o nKOBE DW-308LT and KOBE
DW-308LTP are wires for
welding low carbon 18% Cr
- 8% Ni Stainless steel.
KOBE DW-316LT is a wire for
welding low carbon 18% Cr
- 12% Ni - 2% Mo Stainless
steel, all the wires are for
cryogenic use.
Cryogenic use (-196C)
Cryogenic use (-196C)
Cryogenic use (-196C)
KOBE DW-308LT
KOBE DW-308LTP
KOBE DW-316LT
A n w e n d u n gKOBE DW-308LT und KOBE
DW-308LTP eignen sich fr
kohlenstoffarme 18% Cr
8% Ni hochlegierte Sthle.
KOBE DW-316LT eignet sich
fr kohlenstoffarme 18% Cr
- 12% Ni - 2% Mo
hochlegierte Sthle, vor
allem im Tieftemperatur-
bereich.
Kaltzh (-196C)
Kaltzh (-196C)
Kaltzh (-196C)
A p p l i c a t i o nKOBE DW-308LT et KOBE DW-
308LTP pour le soudage
dacier inoxydable faible
teneur en carbone 18% Cr
8% Ni.
KOBE DW-316LT pour le
soudage dacier inoxydable
faible teneur en carbone 18%
Cr - 12% Ni - 2% Mo pour
applications cryogniques.
Applications cryogniques
(-196C)
Applications cryogniques
(-196C)
Applications cryogniques
(-196C)
KOBE DW-308LT
80% Ar - 20% CO2 / 100% CO2EN 12073 T 19 9 L R C/M 3
AWS A5.22 E308LT0-1/-4
Wst. Nr. 1.4316
KOBE DW-308LTP
80% Ar - 20% CO2 / 100% CO2EN 12073 T 19 9 L P C/M 1
AWS A5.22 E308LT1-1/-4
Wst. Nr. 1.4316
KOBE DW-316LT
80% Ar - 20% CO2 / 100% CO2EN 12073 T 19 12 3 L P C/M 3
AWS A5.22 E316LT1-1/-4
Wst. Nr. 1.4430
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-308LT 0.03 0.5 2.3 0.018 0.007 10.3 18.6 - - - 3.0 4.8 5.0
KOBE DW-308LTP 0.03 0.6 1.3 0.018 0.006 9.6 20.1 - - - 12.3 16.3 14.6
KOBE DW-316LT 0.03 0.4 1.2 0.021 0.008 12.4 17.6 2.2 - - 2.7 4.8 4.3
Chemical Analysis Chemische Analyse Analyse Chimique
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) 0C -100C -196C
KOBE DW-308LT 380 530 51 69 1.40 51 0.92 39 0.52
KOBE DW-308LTP 420 640 40 61 1.12 51 0.82 42 0.45
KOBE DW-316LT 405 537 44 74 1.51 53 0.96 34 0.59
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-308LT
KOBE DW-308LTP
KOBE DW-316LT
Polarity (mm)
KOBE DW-308LT = / + 1.2
KOBE DW-308LTP = / + 1.2
KOBE DW-316LT = / + 1.2
CV (J) L.E. (mm) CV (J) L.E. (mm) CV (J) L.E. (mm)
7/26/2019 Kobelco Stainless Steel
19/32
19
A p p l i c at i o nKOBE DW-308H and KOBE
DW-347H are both for
elevated temperature
applications; suitable for
welding stabilized stainless
steel grades 321H and
347H.
For high temperatures
For high temperatures
KOBE DW-308H
KOBE DW-347H
A n w e n d u n gKOBE DW-308H und KOBE
DW-347H sind entwickelt
fr Hochtemperatur-
anwendungen, geeignet zum
Schweien von stabilisierten
Chrom-Nickelsthlen wie z.
Bsp.1.4848 und 1.4550.
Fr hohen Temperaturen
Fr hohen Temperaturen
A p p l i c a t i o nKOBE DW-308H et KOBE
DW-347H pour les
applications hautes
tempratures; conviennent
pour le soudage des aciers
stabiliss inoxydables des
grades 321H et 347H.
Pour hautes de temprature
Pour hautes de temprature
KOBE DW-308H
80% Ar - 20% CO2 / 100% CO2EN 12073 TZ 19 9 H P M/C 1
AWS A5.22 E308HT1-1/-4
Wst. Nr. 1.4948
KOBE DW-347H
80% Ar - 20% CO2 / 100% CO2EN 12073 T 19 9 Nb P C/M 1
AWS A5.22 E347T1-1/-4
Wst. Nr. 1.4551
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-308H 0.06 0.5 1.3 0.018 0.004 9.5 19.3 - - - 6.6 7.5 5.6
KOBE DW-347H 0.03 0.6 1.3 0.018 0.004 10.4 18.7 - - 0.6 6.7 7.3 6.3
Chemical Analysis Chemische Analyse Analyse Chimique
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
KOBE DW-308H 420 600 44 72 0
KOBE DW-347H 440 617 37 83 0
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-308H
KOBE DW-347H
Polarity (mm)
KOBE DW-308H = / + 1.2 1.6
KOBE DW-347H = / + 1.2 1.6
7/26/2019 Kobelco Stainless Steel
20/32
20
A p p l i c at i o nMXA-135N and MXA-410NM
are suitable for joining and
overlay welding of similar
and 13% Cr steels / cast
steels.
For general use
For general use
MXA-135N
MXA-410NM
A n w e n d u n gMXA-135N und MXA-410NM
eignen sich fr
Verbindungen und zum
Auftragschweien von
artgleichen und 13% igen
Cr - Sthlen / Stahlguss-
sorten.
Fr allgemeine Aufgaben
Fr allgemeine Aufgaben
A p p l i c a t i o nMXA-135N et MXA-410NM
sont tous deux conseills
pour le soudage et le
rechargement d'aciers de
mme nuance et d'aciers
13% de Cr couls.
Pour utilisation gnrale
Pour utilisation gnrale
MXA-135N
80% Ar - 20% CO2
MXA-410NM
80% Ar - 20% CO2
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
MXA-135N 0.02 0.6 0.4 0.018 0.006 5.0 12.9 - - - - - -
MXA-410NM 0.02 0.6 0.5 0.019 0.006 4.3 12.3 0.5 - - - - -
Chemical Analysis Chemische Analyse Analyse Chimique
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C PWHT
MXA-135N 810 880 21 55 0 590C x 10hr FC
MXA-410NM 870 920 20 64 0 600C x 1hr AC
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
Welding Positions Schweipositionen Positions de Soudage
MXA-135N
MXA-410NM
Polarity (mm)
MXA-135N = / + 1.2 1.4 1.6
MXA-410NM = / + 1.2 1.4 1.6
7/26/2019 Kobelco Stainless Steel
21/32
21
A p p l i c at i o nDWN-82, DWN-625 and
DWN-625M are
recommended for a variety
of welding applications,
including overlay welding of
carbon steels and heat
treatable low alloy steels.
Nickel based alloys
Nickel based alloys
Nickel based alloys
DWN-82
DWN-625
DWN-625M
A n w e n d u n gDWN-82, DWN-625 und
DWN-625M sind fr
verschiedene Schwei-
anwendungen empfohlen,
darunter zum Auftrag-
schweien von unlegierten
und von fr eine Wrmenach-
behandlung geeignete
niedriglegierte Sthle.
Nickelbasis-Werkstoffe
Nickelbasis-Werkstoffe
Nickelbasis-Werkstoffe
A p p l i c a t i o nDWN-82, DWN-625 et DWN
625M sont recommands pour
de nombreuses applications
comprenant le rechargement
dur d'aciers au carbone et des
aciers faiblement allis traits
thermiquement.
Le nickel a bas des alliages
Le nickel a bas des alliages
Le nickel a bas des alliages
DWN-82
80% Ar - 20% CO2Wst. Nr. 2.4806
DWN-625
80% Ar - 20% CO2Wst. Nr. 2.4621
DWN-625M
80% Ar - 20% CO2Wst. Nr. 2.4621
C Si Mn P S Ni Cr Mo Fe Nb FS FN FNW
DWN-82 0.04 0.2 3.4 0.002 0.005 70.7 21.2 - 1.5 2.3 - - -
DWN-625 0.03 0.3 0.9 0.004 0.004 59.0 21.4 9.2 4.8 3.4 - - -
DWN-625M 0.02 0.6 2.6 0.004 0.004 60.8 21.2 9.9 3.0 2.0 - - -
Chemical Analysis Chemische Analyse Analyse Chimique
Welding Positions Schweipositionen Positions de Soudage
DWN-82
DWN-625
DWN-625M
Polarity (mm)
DWN-82 = / + 1.2
DWN-625 = / + 1.2
DWN-625M = / + 1.2
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
DWN-82 380 650 46 128 0
DWN-625 470 750 44 57 0
DWN-625M 460 730 42 68 0
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
7/26/2019 Kobelco Stainless Steel
22/32
22
A p p l i c at i o nKOBE DW-307 is suitable for
dissimilar joints and buffer
layers on for example high
mangese steel prior to hard-
facing.
KOBE DW-317L is suitable
for welding 316LN and 317L
stainless steels.
KOBE DW-318 is suitable for
applications on stabilized
and non stabilized austenitic
stainless steels.
For general use
For general use
For positional welding
KOBE DW-307
KOBE DW-317L
KOBE DW-318
A n w e n d u n gKOBE DW-307 eignet sich fr
Austenit-Ferrit-Verbindungen
und Pufferlagen, zum Beispiel
auf Manganhartstahl vor dem
Hartauftragschweien.
KOBE DW-317L eignet sich
zum Schweien von
hochlegierten Sthlen der
Reihe 316 LN und 317L.
KOBE DW-318 ist geeignet fr
Anwendungen an nicht-
rostenden stabilisierten und
nicht stabilisierten austeni-
tischen CrNiMo- Sthlen.
Fr allgemeine Aufgaben
Fr allgemeine Aufgaben
Fr alle Positionen
A p p l i c a t i o nKOBE DW 307 est indiqu pour
les joints dissemblables et les
couches tampons par exemple
sur aciers 13% de Mn avant
rechargement dur.
KOBE DW-317L est conseill
pour le soudage des aciers
inoxydables 316LN et 317L.
KOBE DW-318 est conseill
pour les applications sur les
aciers inoxydables
austnitiques stabiliss et non
stabiliss.
Pour utilisation gnrale
Pour utilisation gnrale
Pour soudage en position
KOBE DW-307
80% Ar - 20% CO2EN 12073 T 18 8 Mn R M 3
Wst. Nr. 1.4370
KOBE DW-317L
80% Ar - 20% CO2 / 100% CO2EN 12073 T Z 19 13 4 L R M/C 3
AWS A5.22 E317LT0-4/-1
Wst. Nr. 1.4440
KOBE DW-318
80% Ar - 20% CO2EN 12073 T 19 12 3 Nb P M 2
Wst. Nr. 1.4576
C Si Mn P S Ni Cr Mo N Nb FS FN FNW
KOBE DW-307 0.07 0.6 6.4 0.02 0.008 8.1 19.2 - - - 1.6 3.3 9.1
KOBE DW-317L 0.03 0.6 1.1 0.02 0.007 12.6 19.1 3.5 - - 9.2 11.6 8.7
KOBE DW-318 0.02 0.5 1.3 0.02 0.012 11.6 18.5 2.8 - 0,4 8.9 16.0 12.9
Chemical Analysis Chemische Analyse Analyse Chimique
Welding Positions Schweipositionen Positions de Soudage
KOBE DW-307
KOBE DW-317L
KOBE DW-318
Polarity (mm)
KOBE DW-307 = / + 1.2 1.6
KOBE DW-317L = / + 1.2 1.6
KOBE DW-318 = / + 1.2 1.6
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
KOBE DW-307 393 583 41 48 0
KOBE DW-317L 490 620 35 50 0
KOBE DW-318 511 680 31 57 0
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
7/26/2019 Kobelco Stainless Steel
23/32
A p p l i c at i o nThese are flux cored TIG
filler rods for root pass
welding of stainless steel
pipe without the need for
purging (back shielding gas).
For 18% Cr - 8% Ni type
stainless steel
For dissimilar joints between
stainless and mildsteel or
medium carbon steels.
For 18% Cr - 12% Ni -
2% Mo stainless steel
For 18% Cr - 8% Ni+Nb or
Ti-Stainless steel
TGX-308L
TGX-309L
TGX-316L
TGX-347
A n w e n d u n gDie TGX-Serie besteht aus
WIG-Stben verschiedener
Gten. Einsatzgebiete sind
vor allem Wurzellagen und
Rohrschweiungen ohne
Formiergas.
Fr 18% Cr - 8% Ni Sthle
Fr Verbindung von
hochlegierten mit un und
niedriglegierten Sthlen.
Fr 18% Cr - 12% Ni -
2% Mo
Fr 18% Cr - 8% Ni+Nb oder
Ti-Sthle
A p p l i c a t i o nIl sagit de baguettes
fourres TIG pour le soudage
de la passe de fond de
tuyaux en acier inoxydable,
sans ncessit de purger (gaz
de protection revers).
Aciers inoxydables 18%
Cr - 8% Ni
Soudage dacier inoxydable
lacier au carbone ou acier
faiblement alli.
Aciers inoxydables 18%
Cr - 12% Ni - 2% Mo
Acier inoxydables 18%
Cr - 8% Ni+Nb ou Ti
TGX-308L
100% Ar.
AWS A5.22 R 308LT1-5
Wst. Nr. 1.4316
TGX-309L
100% Ar.
AWS A5.22 R 309LT1-5
Wst. Nr. 1.4332
TGX-316L
100% Ar.
AWS A5.22 R 316LT1-5
Wst. Nr. 1.4430
TGX-347
100% Ar.
AWS A5.22 R 347T1-5
Wst. Nr. 1.4551
23
C Si Mn P S Ni Cr Mo N Nb+Ta FS FN
TGX-308L 0.02 0.8 1.7 0.023 0.005 10.3 19.6 - - - - -
TGX-309L 0.02 0.8 1.5 0.022 0.006 12.6 24.3 - - - - -
TGX-316L 0.02 0.9 1.6 0.023 0.004 12.5 18.9 2.3 - - - -TGX-347 0.02 0.8 1.6 0.021 0.004 10.2 19.0 - - 0.7 - -
Chemical Analysis Chemische Analyse Analyse Chimique
Welding Positions Schweipositionen Positions de Soudage
TGX-308L
TGX-309L
TGX-316L
TGX-347
Polarity (mm) Kg/pack
TGX-308L = / + 2,2 x 1000 mm 5
TGX-309L = / + 2,2 x 1000 mm 5
TGX-316L = / + 2,2 x 1000 mm 5
TGX-347 = / + 2,2 x 1000 mm 5
Rp 0.2% (N/mm2) Rm(N/mm2) A5 (%) CV (J) C
TGX-308L 450 620 47 60 -196
TGX-309L 530 680 32 - -
TGX-316L 440 600 38 110 0
TGX-347 460 630 48 130 0
Mechanical Properties Mechanische Gtewerte Caractristiques Mcaniques
7/26/2019 Kobelco Stainless Steel
24/32
24
21
20
19
18
17
16
15
14
13
12
11
1016 17 18 19 20 21 22 23 24 25 26 27
Austenite
Nickel Equivalent = %Ni + 30 x %C + 30 x %N + 0.5 x %Mn
Chromium Equivalent = %Cr + %Mo + 1.5 x %Si + 0.5 x %Nb
SCHAEFFLERA+Mline
Austenite+ Ferrite
Ferrite
Ferrite
numbe
r
0
2
4
6
8
10
12
14
16
180%
2%
4%
6%
7.6%
8.7%
10.7%
12.3%
13.6%
28
24
20
16
12
8
4
00 4 8 12 16 20 24 28 32 36 40
Chromium Equivalent = %Cr + %Mo + 1.5 x %Si + 0.5 x %Nb
Nickel Equivalent = %Ni + 30 x %C + 0.5 x %Mn
Austenite
A + M
Martensite
F+M
M + F
A+F
A + M + F
0%Ferrite
5%
10%
20%
40%
80%
100%
Ferrite
1818
1616AA
00
22
44
66
88
1010
1212
1414
1818
2020
2222
2424
2626
3030
4040
5050
6060
7070
2828
3535
4545
5555
6565
7575
8585
95958080
9090
100
100
AFAF
FAFA
FF
1414
1212
1010
1818 2020 2222 2424 2626 2828 3030
Nickel Equivalent = %Ni + 35 x %C + 20 x %N + 0.25 x %Cu
Chromium Equivalent = %Cr + %Mo + 0.7 x %Nb
DeLongDiagram
Schaeff
lerDiagram
WRCDiagram-1992
7/26/2019 Kobelco Stainless Steel
25/32
25
WELDING POSITIONS SCHWEIPOSITIONEN POSITION DE SOUDAGE
AWS: 1G
EN PA
AWS: 2G
EN PC
AWS: 3G
EN PG Down Fallend vers le basPF Up Steigend vers le haut
AWS: 4G
EN PE
AWS: 4F
EN PD
AWS: 6G
EN H-LO45
AWS: 3F
EN PG Down Fallend vers le basPF Up Steigend vers le haut
AWS: 5F
EN PG Down Fallend vers le basPF Up Steigend vers le haut
AWS: 2F
EN PB
AWS: 2G
EN PC
AWS: 1F
EN PA
AWS: 1G
EN PA
Butt welds Stumpfnhte Soudage bout bout
Fillet welds Kehlnhte Soudre d'angles
Pipe welds Rohrnhte Soudage de tuyaux
7/26/2019 Kobelco Stainless Steel
26/32
Designates the chemicalcomposition, % (m/m) 1)2)3)4)
1 Kennzeichen fr der chemischeZusammenstellung, % (m/m) 1)2)3)4)
1 Dsigne la compositionchimique, % (m/m) 1)2)3)4)
1
26
E N 1 2 0 7 3 : 1 9 9 9
Alloy Chemical composition of all-weld metal, % (m/m) 1) 2) 3) 4)
Symbol C Si Mn P 5) S 5) Cr Ni Mo Other elements
Martensetic / Ferretic
13 0.12 1.0 1.5 0.030 0.025 11.0 - 14.0 - - -
13 Ti 0.10 1.0 0.80 0.030 0.030 10.5 - 13.0 - - Ti6)
13 4 0.06 1.0 1.5 0.030 0.025 11.0 - 14.5 3.0 - 5.0 0.4 - 1.0 -
17 0.12 1.0 1.5 0.030 0.025 16.0 - 18.0 - - -
Austenitic
19 9 L 0.04 1.2 2.0 0.030 0.025 18.0 - 21.0 9.0 - 11.0 - ~
19 9 Nb 0.08 1.2 2.0 0.030 0.025 18.0 - 21.0 9.0 - 11.0 - Nb7)
19 12 3 L 0.04 1.2 2.0 0.030 0.025 17.0 - 20.0 10.0 - 13.0 2.5 - 3.0 ~
19 12 3 Nb 0.08 1.2 2.0 0.030 0.025 17.0 - 20.0 10.0 - 13.0 2.5 - 3.0 Nb7)
19 13 4 N L8) 0.04 1.2 1.0 - 5.0 0.030 0.025 17.0 - 20.0 12.0 - 15.0 3.0 - 4.5 N 0.08 - 0.20
Austenitic-ferritic. High corrosion resistance
22 9 3 N L
9)
0.04 1.2 2.5 0.030 0.025 21.0 - 24.0 7.5 - 10.5 2.5 - 4.0 N 0.08 - 0.20Fully austenitic High corrosion resistance
18 16 5 N L8) 0.04 1.2 1.0 - 4.0 0.035 0.025 17.0 - 20.0 15.5 - 19.0 3.5 -5.0 N 0.08 - 0.20
Special types
18 8 Mn8) 0.20 1.2 4.5 - 7.5 0.035 0.025 17.0 - 20.0 7.0 - 10.0 - -
20 10 3 0.08 1.2 2.5 0.035 0.025 19.5 - 22.0 9.0 - 11.0 2.0 - 4.0 -
23 12 L 0.04 1.2 2.5 0.030 0.025 22.0 - 25.0 11.0 - 14.0 - -
23 12 2 L 0.04 1.2 2.5 0.030 0.025 22.0 - 25.0 11.0 - 14.0 2.0 - 3.0 -
29 9 0.15 1.2 2.5 0.035 0.025 27.0 - 31.0 8.0 - 12.0 - -
Heat resisting types
22 12 H 0.15 1.2 2.5 0.030 0.025 20.0 - 23.0 10.0 - 13.0 - -
25 208) 0.06 - 0.20 1.2 1.0 - 5.0 0.030 0.025 23.0 - 27.0 18.0 - 22.0 - -
1) If not specified: Mo < 0.75%, Cu < 0.75% and Ni < 0.60%.
2) Single values shown in the table are maximum values.
3) Tubular cored electrodes not listed in the table shall be symbolized similarly and prefixed by the letter z.
4) The results shall be rounded to the same number of significant figures as in the specified value using the rules in accordance with annex B,
Rule A of ISO 31-0:1992.
5) The sum of P an S shall not exceed 0.050%, except for 18 16 5 N L, 18 8 Mn and 29 9.
6) Ti min. 10 x % C, max. 1.5%.
7) Nb min. 8 x % C, max. 1.1%; up to 20% of the amount of Nb can be replaced by Ta.
8) The all-weld metal is in most cases fully austenitic and therefore can be susceptible to micro fissuring or hot cracking. The occurrence of
fissuring/cracking is reduced by increasing the weld metal manganese level and in recognition of this the manganese range is extended for a number
of the grades. 8g- 8
9) Electrodes under this symbol are usually selected for specific properties and may not be directly interchangeable.
Classification system Klassifizierungssystem Systme de classification
EN 12073-T (Ex.) EN 12073:T 19 9L R M 11 2 3 4
T: Indicates a tubular cored electrode
for metal arc welding
T: Zeigt ein Fldrahtelectrode fr dasMetall-lichtbogen-schweien an
T: Destingue un fil lectrode mtaliquenu fourrstin au soudage larc detout autre produit dapport
Designates the procedure Kennzeichen fr das verfahren Dsigne le procd
7/26/2019 Kobelco Stainless Steel
27/32
27
Type of Electrode core2 Art der Drahtfllung2 Garnissage du fil fourr2
Suffix Kennzahl Characteristics Kennzeichnend Caractristiques Symbole
R Rutile, slow freezing slag Rutil, langsam erstarrende Schlacke Base rutile, laitier solidification lente
P Rutile, fast freezing slag Rutil, schnell erstarrende Schlacke Base rutile, laitier solidification rapide fourr
M Metal powder Metalpulver Poudre mtallique
U Self shielding Selbstschtzend Auto-protecteur - Sans gaz
Z Other types Andere Typen Autres types
Indicates the shielding gas3 Kennzeichen fr der Gasschutz3 Indique le gaz de protection3
Suffix Kennzahl Shielding gas Gasschild Gaz de protection
SymboleM EN 439-M2 EN 439-M2 EN 439-M2
Mixed gas without helium Mischgas ohne Helium Le gaz mlang sans l'hlium
C EN 439-C1 EN 439-C1 EN 439-C1Carbon dioxide Kohlendioxid Dioxyde de carbone
N Without a gas shield Ohne einen Gasschild Sans une protection de gaz
Indicates primary welding position4 Kennzeichen fr Schweiposition4 Dsigne le position de soudage4
Suffix Kennzahl Welding position Schweiposition Position de soudage Symbole
1 All positions Alle Positionen Toutes positions
2 All positions, except vertical down Alle Positionen, auer Fallnaht Toutes positions
3 Flat butt weld, flat fillet weld, Stumpfnaht in Wannenposition, A plat, en angle debout,horizontal-vertical fillet weld Kehlnaht in Wannenposition, en corniche
Kehlnaht in Querposition
4 Flat butt weld, flat fillet weld Stumpfnaht in Wannenposition, A plat, en angle deboutKehlnaht in Wannenposition
5 Vertical down and positions Fallnaht und Positionen gem Verticale descendante etaccording to symbol 3 Kennzahl 3 positions du symbole 3
7/26/2019 Kobelco Stainless Steel
28/32
(Ex.) E316L T0 - 11 2 3
E: Indicates welding electrodeR: Indicates a welding rod
E: Zeigt eine Schweielektrode anR: Zeigt eine Schweistab an
E: Indique lectrode de soudageR: Indique baguette de mtal dapport
Designates the chemical composition1 Kennzeichen fr der chemische Zusammenstellung1 Dsigne la composition chimique1
28
A W S A 5 . 2 2 - 1 9 9 5
AWS UNS Cb (Nb)
Classification Number C Cr Ni Mo +Ta Mn Si P S N Cu
E307TX-X W 30731 0.13 18.0-20.5 9.0-10.5 0.5-1.5 - 3.30-4.75 1.0 0.04 0.03 - 0.5
E308TX-X W 30831 0.08 18.0-21.0 9.0-11.0 0.5 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E308LTX-X W 30835 0.04 18.0-21.0 9.0-11.0 0.5 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E308HTX-X W 30831 0.04-0.08 18.0-21.0 9.0-11.0 0.5 0.5-2.5 1.0 0.04 0.03 - 0.5
E308MoTX-X W 30832 0.08 18.0-21.0 9.0-11.0 2.0-3.0 0.5-2.5 1.0 0.04 0.03 - 0.5
E308LMoTX-X W 30838 0.04 18.0-21.0 9.0-12.0 2.0-3.0 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E309TX-X W 30931 0.10 22.0-25.0 12.0-14.0 0.5 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E309LCbTX-X W 30932 0.04 22.0-25.0 12.0-14.0 0.5 0.70-1.00 0.5-2.5 1.0 0.04 0.03 - 0.5
E309LTX-X W 30935 0.04 22.0-25.0 12.0-14.0 0.5 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E309MoTX-X W 30939 0.12 21.0-25.0 12.0-16.0 2.0-3.0 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E309LMoTX-X W 30938 0.04 21.0-25.0 12.0-16.0 2.0-3.0 - 0.5-2.5 1.0 0.04 0.03 0.5
E309LNiMoTX-X W 30936 0.04 20.5-23.5 15.0-17.0 2.5-3.5 - 0.5-2.5 1.0 0.04 0.03 - 0.5E310TX-X W 31031 0.20 25.0-28.0 20.0-22.5 0.5 - 1.0-2.5 1.0 0.03 0.03 - 0.5
E312TX-X W 31331 0.15 28.0-32.0 8.0-10.5 0.5 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E316TX-X W 31631 0.08 17.0-20.0 11.0-14.0 2.0-3.0 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E316LTX-X W 31635 0.04 17.0-20.0 11.0-14.0 2.0-3.0 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E317LTX-X W 31735 0.04 18.0-21.0 12.0-14.0 3.0-4.0 - 0.5-2.5 1.0 0.04 0.03 - 0.5
E347TX-X W 34731 0.08 18.0-21.0 9.0-11.0 0.5 8 x C min. 0.5-2.5 1.0 0.04 0.03 - 0.5
1.0 max
E409TX-X e W 40931 0.10 10.5-13.5 0.60 0.5 - 0.80 1.0 0.04 0.03 - 0.5
E410TX-X W 41031 0.12 11.0-13.5 0.60 0.5 - 1.2 1.0 0.04 0.03 - 0.5
E410NiMoTX-X W 41036 0.06 11.0-12.5 4.0-5.0 0.40-0.70 - 1.0 1.0 0.04 0.03 - 0.5
E410NiTiTX-X e W 41038 0.04 11.0-12.0 3.6-4.5 0.5 - 0.70 0.50 0.03 0.03 - 0.5
E430TX-X W 43031 0.10 15.0-18.0 0.60 0.5 - 1.2 1.0 0.04 0.03 - 0.5
E2209TX-X W 39239 0.04 21.0-24.0 7.5-10.0 2.5-4.0 - 0.5-2.0 1.0 0.04 0.03 0.08-0.20 0.5
E2553T0-X W 39533 0.04 24.0-27.0 8.5-10.5 2.9-3.9 - 0.5-1.5 0.75 0.04 0.03 0.10-0.20 1.5-2.5
R308LT1-5 W 30835 0.03 18.0-21.0 9.0-11.0 0.5 - 0.5-2.5 1.2 0.04 0.03 - 0.5
R309LT1-5 W 30935 0.03 22.0-25.0 12.0-14.0 0.5 - 0.5-2.5 1.2 0.04 0.03 - 0.5
R316LT1-5 W 31635 0.03 17.0-20.0 11.0-14.0 2.0-3.0 - 0.5-2.5 1.2 0.04 0.03 - 0.5
R347T1-5 W 34731 0.08 18.0-21.0 9.0-11.0 0.5 8 x C min. 0.5-2.5 1.2 0.04 0.03 - 0.5
1.0 max
a) The weld metal shall be analyzed for the specific elements in this table. If the presence of other elements is indicated in the course of this work, the
amount of those elements shall be determined to ensure that their total (excluding iron) does not exceed 0.50%.
b) Single values shown are maximum.
c) In this table, the X following the T refers to the position of welding (1 for all-position operation or 0 for flat or horizontal operation) and the X
following the dash refers to the shielding medium (-1,-4, or -5) as shown in the AWS Classification column in Table 2. For information concerning the
G, see A2.3.7 and A2.3.8 of the Annex. In A5.22-80, the position of welding was not included in the c lassification. Accordingly, electrodes classified
herein as either EXXXT0-1 or EXXXT1-1 would both have been classified EXXXT-1 and so forth.d) ASTM/SAE Unified Number System for Metals and Alloys.
e) Titanium - 10 x C min., 1.5% max.
A5.22 : E T -
Weight % a,b Gewicht % a,b Poids % a,b
Classification system Klassifizierungssystem Systme de classification
Designates the procedure Kennzeichen fr das verfahren Dsigne le procd
7/26/2019 Kobelco Stainless Steel
29/32
29
Indicates primary welding position2 Kennzeichen fr Schweiposition2 Dsigne le position de soudage2
Indicates the shieldinggas and the current type
3 Kennzeichen fr derGasschutz und der Stromart
3 Indique le gaz de protectionet la polarit
3
Suffix
Kennzahl
Welding position
Schweiposition
Position de soudage
Symbole
0 Flat position Normal und Horizontal Position A plat
1 All positions Alle Positionen Toutes positions
Suffix Shielding gas Current type Process (T) Kennzahl Gasschutz Stromart Verfahren (T)
Symbole Protection Polarit Procd (T)1 CO2 DC / EP Cored wire Flldraht Fil fourr
3 None Keine Sans DC / EP Cored wire Flldraht Fil fourr
4 80%Ar + 20%CO2 DC / EP Cored wire Flldraht Fil fourr
5 100% Ar DC / EN TIG WIG TIG
7/26/2019 Kobelco Stainless Steel
30/32
30
List of addressesJ a p a n : Ko b e S t e e l , L t d .
International Operations Dept. Welding Division
Kobelco Bldg., 2-3-2 Toyo, Koto-Ku, Tokyo 135, Japan
Tel.: (++81) 3 5634-5031, Fax: (++81) 3 5634-5047
www.kobelco.co.jp/english
E u r o p e : Ko b e l c o W e l d i ng o f E uro p e B . V .
Eisterweg 8, 6422 PN, Heerlen, The Netherlands
Tel.: (++31) 45-5471111, Fax: (++31) 45-5471100
www.kobelcowelding.nl
marketing@kobelcowelding.nl
N o r th A me r i c a : Ko b e l c o W e l d i ng o f A me r i c a I n c .
7478, Harwin Drive, Houston, Texas 77036, USA
Tel.: (++1) 713 974-5775, Fax: (++1) 713 974-6543
S o u t h e a s t A s i a : Ko b e W e l d i ng o f Ko r e a c o . , L t d .21-14 Palryong-Dong, Changwon, Kyongnam
Republic of Korea
Tel.: (++82) 551 92-6886, Fax: (++82) 551 92-7786
Ko b e W e l d i ng ( S i n g a p o r e ) P t e . L t d .
20, Pandan Avenue, Jurong, Singapore 609387,
Republic of Singapore
Tel.: (++65) 2682711, Fax: (++65) 2641751
T ha i - Ko b e W e l d i ng Co . , L t d .
500, Soi 1, Bangpoo Industrial Estate, Sukhumvit Road,
Praeksa, Samutprakarn, 10280 ThailandTel.: (++66) 2 324-0588~0591, Fax: (++66) 2 324-0797
Ko b e M i g W i r e ( T h a i l a nd ) Co . , L t d .
491, Soi 1, Bangpoo Industrial Estate Sukhumvit Road,
Praeksa, Samutprakarn, 10280 Thailand
Tel.: (++66) 2 324-05 88~0591, Fax: (++66) 2 324-0797
Ko b e W e l d i ng o f T a ng s ha n Co . , L t d .
196, Huoju Road, Tangshan, New & High-Tech
Development Zone, Tangshan, Hebel, 063020
Peoples Republic of China
Tel.: (++86) 315 385 2806, Fax: (++86) 315 385 2829
7/26/2019 Kobelco Stainless Steel
31/32
7/26/2019 Kobelco Stainless Steel
32/32
Eisterweg 8