Post on 09-Mar-2018
transcript
OILS, GEASES, CAR CARE Production Reference Book. First edition (supplemented and revised) / Edited by Candidate of Chemical Sciences V. I. Gumenniy — “Agrinol”, 2016 (№2) — 166 p.
The reference book contains brief information about the purpose, fields of use and normative quality indices of the lubricants produced by the Limited Liability Company “Agrinol”. The reference book can be used as a guide to choose and utilize the association’s production.
© RU SIE “Agrinol”, 2016
“Agrinol” specializes in the production of such lubricating materials as lubricants, oils, lubricating and cooling liquids (LCL) and steel drums. The introduction of new technologies and the improvement of the already existing ones by modernizing the equipment and utilizing new materials, highly qualified specialists and the quality management system ISO 9001 – 2009 (ISO 9001:2008) enable the enterprise to manufacture products of high quality that corresponds to the requirements of Ukrainian and foreign consumers. The oils, greases and LCL produced by RU SIE “Agrinol” are widely used at enterprises of concentrating, metallurgical and power supply complexes as well as in mechanical engineering, transport, and agricultural sector in 35 countries.
On the basis of the modern control and analytical laboratory accredited in accordance with ISO17025:2006, as well as the experimental laboratory in the association, constant effort is being made to increase the range and quality of product that helps to ensure the fullest satisfaction of the requirements of specific consumers.
This enables our enterprise to guarantee the best satisfaction of specific consumers’ requirements.
“Agrinol” is always opened to mutual beneficial collaboration with all the enterprises and organizations interested in the development, industrial production assimilation and application of new types of lubricating products.
A structural subdivision forms a part of the company produces metal drums for petroleum, chemicals, food and other products. Manufacturing takes place in modern production lines, which provides along with high product quality, competitive price packaging. The range of packaging meets state standards, specifications and UN international rules for transport of dangerous goods.
The reference book contains brief information about the purpose, fields of use and normative quality indices of the lubricants produced by the Agrinol. The reference book can be used as a guide to choose and utilize the association’s production.
For further information, please, visit our web-site:www.agrinol.ua
LLC “RU SIE Agrinol”71100, Ukraine, Berdyansk,84/1, Melitopolskoe shosse. tel. +38 (06153) 60-600
REFERENCE BOOK
4
C
onte
nts
Contents
Contents ........................................................................4
OILS ..............................................................7
Agrinol universal multigrade motor oils ..9
Oils for automotive diesels ............................15
Universal mineral motor oils ........................20
Oils for 2- and 4-stroke engines of small machinery ....................................................21
Oils for marine and locomotive engines 23
Chain Saw Oil ........................................................24
Oils for marine and locomotive engines 26
Transmission oils ..................................................30Transmission oils in accordance with GOST 23652-79 .................................... 32Agrinol Transmission oils ...........................34Transmission oils for industrial an obsolete equipment .....................................36Automatic transmission fluid ...................37
Universal oils for automotive diesels ......38
Oils for hydromechanical transmissions 40
Hydraulic oils ..........................................................41Low-temperature oils .................................. 41Turbine oils according to GOST 9972-74, GOST 10289-79 ........................... 42
Power oils ..................................................................42Kompressoil VG ..............................................44Compressor oils for gas-transit units .... 47Тransformer oils ............................................49Cable oils .......................................................... 51
Industrial oils ..........................................................52
Hydraulic oils of premium group ............ 53Zinc-free hydraulic oils of premium group ..................................................................56Gear oils premium group............................ 57For rolling mills ............................................. 59Oils for slideways .......................................... 61Oils for liquid friction bearings ............... 62General purpose oils ....................................64Industrial petroleum oils ........................... 65Vacuum oils ..................................................... 71Oil heat transfer fluid ..................................72Flushing oils ....................................................73Conservative oils ........................................... 74Release agent Form Divider ...................... 75Instrumental oils ........................................... 76
GREASE .................................................... 79
General-purpose lubricants for standard temperatures .....................................81
General-purpose lubricants ..........................84
Automotive lubricants.......................................85
Multi-purpose lubricants .................................87
for standard and high temperatures ........91Water-resistant ............................................... 92
Industrial lubricants ...........................................92Metal-plating lubricants ..........................105Industrial lubricants for rolling mills ..106
Railway Greases .................................................. 107
Heat-resistant greases.....................................111
Chemically resistant lubricants .................116
ContentsREFERENCE BOOK
5
C
onte
nts
Drilling lubricants ..............................................118
Low-temperature lubricants .......................119
Rope greases ........................................................ 120
Instrumental lubricants ................................. 123
Marine lubricants ...............................................124
Consrevation (protective) lubricants .... 125
Sealing lubricants ............................................. 126
Reducer lubricants (semi-fl uid) ................ 128
Brake- in pastes .................................................. 129
Insulation lubricants ....................................... 130
TECHNOLOGICAL COOLING LUBRICANTS .......................................133
Oil coolants ............................................................135
Water-based cooling lubricants ............... 137
AUTO CHEMISTRY ............................145
Cooling liquids ....................................................147
Windshield fl uids ................................................149
METAL PACKING ................................151
Production of metal packing with the logo ...........................................................152Painting of metal DRUMS ........................152
Metal packing ...................................................... 152
Steel drum, tight-head type 1A1L 216,5 dm3 .................................................................153
Steel drum, open-head type 1A2L 213 dm3 .....................................................................153
Drum CD-1A2 18 20 dm³ .............................. 154
Correspondence table products ................155
Annex .........................................................................161
Index .......................................................................... 162
REFERENCE BOOK
8
OIL
S
Specialists of the “Agrinol” company developed line of motor oils, adapted to the domestic conditions of mobile equipment operation. These oils contain specially selected and balanced components which actively cleanse and protect engine parts from deposits and sludge. The range of Agrinol SAE motor oils includes PREMIUM class oils for modern cars, cargo, passenger and road-construction vehicles, which are working under the heavy loads; and also oils of STANDART class for the older models.
New generation transmission oils “Transmission” and automatic transmission fluid (ATF) include both mineral and synthetic oils that are intended for use in extreme conditions where increased antioxidant and EP properties are needed.
“Agrinol” company produces a full range of traditional lubricants along with high-tech, synthetic and semi-synthetic lubricants for the last generation automotive technique.
REFERENCE BOOK
9
OIL
S
Agr
inol
uni
vers
al m
ultig
rade
mot
or o
ils
Agrinol universal multigrade motor oils
TS U 23.2-30802090-085:2009
Agrinol 5W 30 SL/CF — fuel economy low-viscosity synthetic universal oil for gasoline and diesel engines of a new generation, adjusted to requirements for architecture of engine with temperate emissions and low friction, including turbocharged, multivalve engines and engines equipped with devices pre-treatment of exhaust gases operated under the regime of "start-stop" and the conditions of urban traffic.
Agrinol 5W 30 SM/CF — fuel economy low-viscosity synthetic oil for lubrication of all gasoline and diesel engines (including turbocharged, multivalve, direct injection), as well as for cars and off-road vehicles, gas-fueled, in which must apply low viscosity and a low friction oil.
Agrinol 5W 40 SN/CF — Universal synthetic oil of new generation, recommended for modern high-augmented gasoline engines with turbocharging and diesel engines with supercharge of cars, minibuses and light trucks of European, American and Japanese manufacturers, sport cars, as well as 4-strokes gasoline engines on motorbikes. Oil increases the efficiency of fuel consumption while maintaining engine power.
Perfomance level:Agrinol 5W-30 SL/CF FUEL ECONOMY (ACEA A3 / B4 / C3, API SL/CF)VW 502.00 / 505.00, Ford WSS-M2C913-C / WSS-M2C913-D, BMW LL-01 FE, ACEA A3 / B4 / C3
Agrinol 5W-30 SM/CF FUEL ECONOMY (ACEA А5 / В5, API SM/CF)VW 502.00 / 505.00, Ford WSS-M2C913-C / WSS-M2C913-D, BMW LL-01 FE, ACEA А5 / В5
Agrinol 5W-40 SN/CF PREMIUM (ACEA А3 / В3 / В4, API SN/CF)BMW LL-01, MB-229.5, Porsche A40, VW 502.00 / 505.00, Renault RN 0700 / 0710, ACEA А3 / В3 / В4
Index name 5W-30 SL/CF 5W-30 SM/CF 5W-40 SN / CF
Temperature range –30 ... +30 –30 ... +40
Kinematic viscosity at 100°С, mm2/s 9,3-12,5 12,5-16,3
Viscosity index, not less than 150 145 160
TBN, mg КОН/g, not less than 6,5 8,0 7,0
Sulphated ash, %,not more than 1,2 1,3
Temperature, °С:• Open cup fl ash point, °С, not less
than• Pour point, not more than
205–35
200–35
205–36
Color, CNT units, not more than 3,0
Mass fraction of the active elements, %, not less than: • Calcium• Zinc
0,250,1
0,20,1
0,280,1
Agrinol universal multigrade motor oilsREFERENCE BOOK
10
OIL
S
Agr
inol
uni
vers
al m
ultig
rade
mot
or o
ils
TS U 23.2-30802090-085:2009
Agrinol 5W-40 SL/CF, CG-4/SJ — universal synthetic motor oils, intended for use in modern gasoline and diesel engines of cars, trucks and off-road equipment, operating in any environmental conditions and with extreme type of driving (highlands, “start-stop” mode, sport style).
Agrinol 10W-40 SL/CF, CG-4/SJ — universal semi-synthetic motor oil intended for all types of modern diesel and gasoline engines of cars and minibuses (including turbocharged engines and catalyst). It is an optimal decision for mixed fleets.
SL/CF oils are used in engines operating on fuel with a sulfur content of 0.5% of the mass and above.
Perfomance level:Agrinol 5W-40 SL/CF PREMIUM (ACEA А3/B4, API SL/CF)VW 502.00/505.00, Porsche A40, BMW LL-01, PSA B71 2296, Renault RN0710/RN0700, MB-229.5
Agrinol 5W-40 CG-4/SJ PREMIUM-DIESEL (ACEA E3-96/B3-96/A2-96, API CG-4/SJ)MB-228.1, VW 501.01/ 505.00
Agrinol 10W-40 SL/CF OPTIMAL (ACEA А3/B4, API SL/CF)BMW LL-98, MB-229.1, VW 502.00/505.00
Agrinol 10W-40 CG-4/SJ HP-DIESEL (ACEA E3-96/B3-96/A2-96, API CG-4/SJ)MB-228.1/228.3, VW 501.01/505.00, MAN 271, 3275, Volvo VDS/VDS-2, ЯМЗ-4-02
Index nameAgrinol 5W-40 CG-4/SJ
Agrinol 5W-40 SL/CF
Agrinol 10W-40 CG-4/SJ
Agrinol 10W-40 SL/CF
Temperature range –30 ... +40 –25 ... +40
Kinematic viscosity at 100°С, mm2/s 12,5-16,3
Viscosity index,not less than 140 130
TBN, mg КОН/g, not less than 8,5 8,5 9,0 8,5
Sulphated ash, %, not more than 1,5 1,5 1,5 1,5
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200–35
200–28
200–32
Color, CNT units, not more than 3
Mass fraction of active elements,%, not less than• Calcium• Zinc
0,250,10
0,250,10
0,280,11
0,250,11
Agrinol universal multigrade motor oilsREFERENCE BOOK
11
OIL
S
Agr
inol
uni
vers
al m
ultig
rade
mot
or o
ils
TS U 23.2-30802090-085:2009
10W-30 SM / CF: — fuel economy universal semi-synthetic motor oil for modern multi-valve gasoline and diesel engines with hydraulic lifter (including turbocharges) cars, vans, SUVs and light trucks manufactured after 2004, working under extremely difficult conditions (idling, "start-stop" mode all year round, including the cold winter). It can be used in diesel engines released after 1994 on diesel fuel with a sulfur content up to 0.5%.
10W-40 CI-4 / SL: universal semi-synthetic oil for high-speed four-stroke gasoline and diesel engines of cars and trucks, multi-valve, turbocharged (including the exhaust gas recirculation system (EGR) with direct injection. The optimal solution for the mixed fleets.
Agrinol SAE 10W-40 CI-4 – is a universal semi-synthetic motor oil, Low SAPS category (with low content of Sulphated Ash, Phosphorus and Sulphur), for high-speed four-cycle engines with different types of fuel injection and supercharging (models from 2002 manufacturing year). For engines with systems of Exhaust Gase Recirculation (EGR).
Perfomance level:Agrinol 10W-30 SM / CF FUEL ECONOMY (ACEA А1 / В1 / С2, API SM/CF)VW 502.00 / 505.00, Ford WSS-M2C913-C, МВ 229.1, ACEA А1 / В1 / С2
Agrinol 10W-40 CI-4 / SL PREMIUM (ACEA А3 / В3 / В4 / E7, API CI-4/SL)MB-228.3, 229.1, VW 500.00 / 505.00, Renault (RVI) RLD-2, Volvo VDS-3, MAN 3275, ACEA А3 / В3 / В4 / E7
Agrinol 10W-40 CI-4 PREMIUM (ACEA E7 / E5 / E3 / B3 / B4, API CI-4)BMW LL-98, MB-228.3, MAN M3275, Mack EO-M Plus, RVI RLD / RVI RLD-2, Volvo VDS-2 / VDS-3,
CAT ECF-1-a, Global DHD-1, Cummins CES 20076 / 77 / 78, Jaso DH-1, MTU Type 2, ACEA E7 / E5 / E3 / B3 / B4
Index name 10W-30 SM/CF
10W-40 CI-4/SL
10W-40 CI-4low SAPS
Temperature range –25...+30 –25...+40 –25...+40
Kinematic viscosity at 100°С, mm2/s 9,3-12,5 12,5-16,3 13,0-16,5
Viscosity index, not less than 135 140 140
TBN, mg КОН/g, not less than 7,0 10,0 9,5
Sulphated ash, %,not more than 1,2 1,6 1,0
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
200–32
205–32
210–32
Color, CNT units, not more than 3,0 3,5 2,5
Mass fraction of active elements, %, not less than: • Calcium• Zinc
0,20,1
0,280,11
0,20,09
Agrinol universal multigrade motor oilsREFERENCE BOOK
12
OIL
S
Agr
inol
uni
vers
al m
ultig
rade
mot
or o
ils
TS U 23.2-30802090-085:2009
Agrinol 15W-40 CG-4/SJ, CG-4/SL are mineral, universal, motor oils, which are used in high-speed, four-stroke diesel engines of HPD (High Performance Diesel) class with and without turbocharging.
Agrinol 15W-40 CН-4/SJ — universal, mineral based motor oil, intended for high-load, high-speed, fourstroke diesel engines of class HPD main type, that use fuel with a sulfur content exceeding 0,5 % by weight.
Agrinol 15W-40 CI-4 — mineral based universal motor oil, intended for exploitation of four-stroke diesel engines with various types of injection systems and pressurization (ranged from 2002 release).
Perfomance level:Agrinol 15W-40 CG-4/SJ HP-DIESEL (ACEA E2-96/B2-98/A2-96, API CG-4/SJ)MB 228.1, VOLVO VDS, MAN 271, VW 505.00/501.01
Agrinol 15W-40 CG-4/SL (ACEA A3/B3, API CG-4/SL)MB228.1, 229.1, VW501.01/505.00
Agrinol 15W-40 CH-4/SJ TRUCK-DIESEL (ACEA E2-04/B3/A2-02, API CH-4/SJ)Cummins 20076/71, MAN 271, MTU Type 1, CAT ECF-1-a, Mack E-OM Plus, MB 228.1, Volvo
VDS-2, Deutz DQC II-10, Renault RD/RD-2, AllISOn C-4
Agrinol 15W-40 CI-4 GRAND DIESEL (ACEA E7/E5/E3/B3/B4, API CI-4)BMW LL-98, MB-228.3, MAN M3275, Mack EO-M Plus, Renault RVI RLD / RVI RLD-2, Volvo VDS-
2/VDS-3, CAT ECF-1-a, Global DHD-1, Cummins CES 20076/77, Jaso DH-1, MTU Type 2
Index nameAgrinol 15W-40 CG-4/SJ
Agrinol 15W-40 CG-4/SL
Agrinol 15W-40 CH-4/SJ
Agrinol 15W-40
CI-4
Temperature range –25 ... +40
Kinematic viscosity at 100°С, mm2/s 12,5-16,3
Viscosity index,not less than 120
TBN, mg КОН/g, not less than 8,5 9 9 7,5
Temperature, °С: • Open cup fl ash point, °С, not less than • pour point, not more than
205–32
205–28
Color, CNT units, not more than 4
Sulphated ash, %, not more than 1,5
Mass fraction of active elements,%,not less than• Calcium• Zink
0,250,10
Agrinol universal multigrade motor oilsREFERENCE BOOK
13
OIL
S
Agr
inol
uni
vers
al m
ultig
rade
mot
or o
ils
TS U 23.2-30802090-085:2009
Agrinol 10W-40 CF-4/SH, SG/CD — universal semi-synthetic motor oils.Agrinol 15W-40 CF-4/SG — universal mineral based motor oils.These oils are intended for lubricating of high-octane gasoline and powerful
four-stroke diesel engines (main type) of cars and microbuses, including turbocharged engines and catalyst. Products are recommended for home equipment and for mixed vehicle fleets, as well as for engines working on gas fuel.
Agrinol 15W-40 SF/CC, SG/CD — universal mineral based motor oil for highly-accelerated turbocharged engines, and engines without it, working in severe conditions on sour fuel as well as for unleaded gasoline with oxygenates.
Products are recommended for obsolete equipment.Perfomance level:Agrinol 10W-40 SG/CD CLASSIC (ACEA А2/B2/E1-96, API SG/CD), MB 229.1, VW 500.01/505.00,
MIL-L-46152B,-2104C, CCMC G5/PD-2
Agrinol 10W-40 CF-4/SH EXTRA DIESEL (ACEA E2-96/B3-98/A2-96), MB 228.1, VOLVO VDS, MAN 271
Agrinol 15W-40 SF/CC STANDARD (ACEA A2/B2, API SF/CC), MIL-46152-C; -46152E, CCMC G2/D1
Agrinol 15W-40 SG/CD CLASSIC (ACEA А2/B2/E1-96, API SG/CD), MB 229.1, VW 501.01/505.00, MIL-L-46152Е, CCMC G5/PD-2/D4
Agrinol 15W-40 CF-4/SG EXTRA DIESEL (ACEA E2-04/B3-98/A2-96, API CF-4/SG), MB 228.1, 227.1, VOLVO VDS, MAN 271, VW 505.00, AllISOn C-4, Mil-L-2104E/46152C
Index nameAgrinol 10W-40 SG/CD
Agrinol 10W-40 CF-4/SH
Agrinol 15W-40 SF/CC
Agrinol 15W-40 SG/CD
Agrinol 15W-40 CF-4/SG
Temperature range –25 ... +40
Kinematic viscosity at 100°С, mm2/s 12,5-16,3
Viscosity index,not less than 130 115 120
TBN, mg КОН/g, not less than 7,5 7,5 6 7,5 8,2
Temperature, °С: • Flash point in open crucible,
notless than • Pour point, not more than
200–28
200–32
205–25
210–28
205–30
Sulphated ash, %, not more than 1,3 1,4 1,5
Mass fraction of active elements,%,not less than• Calcium• Zink
0,200,10
0,230,10
0,200,10
0,23010
Agrinol universal multigrade motor oilsREFERENCE BOOK
14
OIL
S
Agr
inol
uni
vers
al m
ultig
rade
mot
or o
ils
TS U 23.2-30802090-085:2009
Agrinol 15W-30 SF/CE — universal tractor oil used in all types of diesel engines, including: turbocharged, hydraulic systems, hydrostatic and mechanical transmissions, wet brake systems and multi-disc clutches, power shafts and hydraulic boosters for all types of tractors.
Agrinol 20W-40 SF/CC, Agrinol 20W-50 SF/CC are mineral-based multi-grade engine oils. Oils are designed for the lubrication of all gasoline and diesel engines in passenger cars of domestic and foreign production, including a turbocharged heavy-duty engines.
Oil Agrinol 20W-50 SF/CC is specially adapted for engines with high degree of deterioration and equipment working in the southern regions.
Perfomance level:Agrinol 20W-40 SF/CC STANDARD (ACEA A2/B2, API SF/CC)MIL-46152-C; -46152E, CCMC G2/D1
Agrinol 20W-50 SF/CC STANDARD (ACEA A2/B2, API SF/CC)MIL-46152-C; -46152E, CCMC G2/D1
Index name Agrinol 15W-30 SF/CE
Agrinol 20W-40 SF/CC
Agrinol 20W-50 SF/CC
Temperature range –20 ... +40 –20 ... +45 –20 ... +50
Kinematic viscosity at 100°С, mm2/s 9,3-12,5 12,5-16,3 16,3-21,9
Viscosity index,not less than 120
TBN, mg КОН/g, not less than 9,0 6,0
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
210–25
210–28
215–28
Sulphated ash, %, not more than 1,5 1,3
Mass fraction of active elements,%,not less than• Calcium• Zink
0,250,10
0,200,08
REFERENCE BOOK
15
OIL
S
Oils
for a
utom
otiv
e di
esel
s
Oils for automotive diesels
TS U 23.2-30802090-085:2009
Agrinol SAE 10W CF-4 oil is designed for the lubrication of locomotive and marine diesel engines, bulldozer diesel engines of domestic and foreign production, metallurgical equipment of mining enterprises, various diesel engines operating in different conditions, drilling equipment etc.
Agrinol SAE 30 CF-4 and Agrinol SAE 40 CF-4 oils are designed for diesel engines of heavy trucks, mining and construction equipment operating under severe conditions. Agrinol SAE 30 CF-4 can be used during the spring and autumn periods the hydraulic oil ISO 100 in hydrodrives of construction, mining and special equipment.
Agrinol SAE 40 CF-4 can be used in summer or in hot climates.Agrinol SAE 50 CF-4 il is designed for seasonal use in summer period in the
highly accelerated diesel engines of trucks, road construction, agricultural and engineering machinery with engines of Euro-I и Euro-II environmental norms, operating in difficult conditions.
Perfomance level:Agrinol SAE 10W CF-4 (ACEA E3/B3/B4, API CF-4, ISO VG32)AllISOn C-3/4 Fluids, Cat TO-2, Vickers 35VQ25 Pump Test, MACK EO-K/2, MAN 270/271GM 6094-M, MiL-PRF-2104G, -L-46152E
Agrinol SAE 30 CF-4 (ACEA E3/B3/B4, API CF-4, ISO VG68)AllISOn C-3/4 Fluids, Cat TO-2, MACK EO-K/2, MAN 270/271, GM 6094-M, MiL-PRF-2104G,
-L-46152E, КАМАЗ, ЯМЗ-3-02
Agrinol SAE 40 CF-4 (ACEA E3/B3/B4, API CF-4, ISO VG150)AllISOn C-4 Fluids, MACK EO-K/2, MAN 270/271, GM 6094-M, MiL-PRF-2104G, -L-46152E,
LMOA G V
Index name Agrinol SAE 10W CF-4
Agrinol SAE 30 CF-4
Agrinol SAE 40 CF-4
Agrinol SAE 50 CF-4
Kinematic viscosity at 100°С, mm2/s 4,1-5,6 9,5-12,5 13,5-15,0 16,3-21,9
Viscosity index,not less than 95 95 95 92
TBN, mg КОН/g, not less than 9,0 9,0 9,0 9,0
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
190–30
220–20
220–15
225–15
Sulphated ash, %, not more than 1,5 1,5 1,5 1,5
Mass fraction of active elements,%,not less than• Calcium• Zink
0,300,1
0,300,1
0,300,1
0,300,1
Oils for automotive dieselsREFERENCE BOOK
16
OIL
S
Oils
for a
utom
otiv
e di
esel
s
GOST 8581-78
M-8G2, M-8G2k are winter oils for diesel automotive engines, including those with moderate turbocharging, stationary diesel engines and diesel generators operating under severe conditions. Temperature range: from minus 20°С to + 25°С.
М-8G2k oil unlike М-8G2 have more effective additive composition, which increases terms of oil change. Recommended for vehicles of KAMAZ, ZIL type and for “Ikarus”-type buses.
Operating temperature range: from minus 5°С to + 30°С.
Index name М-8G2
М-8G2k
Extra class First class
Compliance with classifi cations SAE (API) 20 (СС ) 20 (СС )
Kinematic viscosity at 100°С, mm2/s 8,0±0,5 7,5–8,5
Viscosity index, not less than 85 95 90
TBN, mg КОН/g, not less than 6,0 6,0
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200Minus 25
210Minus 30
200Minus 30
Sulphated ash, %, not more than 1,65 1,15
Degree of purity, mg on 100 g of oil, not more than 500 450 500
Mass fraction of active elements, %, not less than
• Calcium • Zinc • Phosphorous
0,150,060,06
0,190,050,05
Oils for automotive dieselsREFERENCE BOOK
17
OIL
S
Oils
for a
utom
otiv
e di
esel
s
GOST 8581-78
М-10G2, М-10G2k — summer oils for lubrication of automotive diesel engines, including those with moderate turbocharging, high-speed stationary diesel engines and diesel generators working in the operating conditions under which sedients are formed by high temperatures.
М-10G2k oil unlike М-10G2 have more effective additive composition, which increases terms of oil change. Recommended for vehicles of KAMAZ, ZIL type and for “Ikarus”-type buses.
Operating temperature range: from minus 5°С to + 30°С.
Index name М-10G2
М-10G2k
Extra class First class
Compliance with classifi cations SAE (API) 30 (СС ) 30 (СС )
Kinematic viscosity at 100°С, mm2/s 11,0±0,5 11,0±0,5
Viscosity index, not less than 85 95 85
TBN, mg КОН/g, not less than 6,0 6,0
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
205Minus 15
220Minus 18
205Minus 15
Sulphated ash, %, not more than 1,65 1,15
Degree of purity, mg on 100 g of oil, not more than 500 450 500
Mass fraction of active elements, %, not less than
• Calcium • Zinc • Phosphorous
0,150,060,06
0,190,050,05
Oils for automotive dieselsREFERENCE BOOK
18
OIL
S
Oils
for a
utom
otiv
e di
esel
s
GOST 8581-78
M-10V2 — summer oil for lubricating of middle-accelerated automotive diesels SMD-14, А-41, D-50, D-37 and others. Operating temperature range: summer oil М-10V2: from minus 5°С to +30°С.
TS U 23.2-30802090-085:2009
Agrinol М-14G2k is intended for lubricating of four-stroke transport diesel engines, highly accelerated automotive diesels without supercharging (or with limited supercharging), that operate under moderate and heavy conditions. Agrinol М-14G2k oil can be used instead of М-10G2k motor oil according to GOST 8581 for summer operation of automotive diesels in regions with long and hot summers. Temperature range: from minus 20°С to +40°С.
Index name М-10V2 Agrinol М-14G2k
Compliance with classifi cations SAE (API) 30 (СВ ) 40 (СС)
Kinematic viscosity at 100°С, mm2/s 11,0±0,5 14,0–15,5
Viscosity index, not less than 85 90
Total Base Number, mg КОН/g, not less than 3,5 6,0
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
205Minus 15
215Minus 25
Sulphated ash, %, not more than 1,3 1,15
Mass fraction of active elements, %, not less than • Calcium • Zinc • Phosphorous
0,080,050,05
0,190,050,05
Oils for automotive dieselsREFERENCE BOOK
19
OIL
S
Oils
for a
utom
otiv
e di
esel
s
GOST 8581-78
М-8DM, М-10DM — oil is intended for summer use for highly accelerated automotive diesels, high-speed stationary diesels and diesel generators of domestic and foreign production with turbo charger and without it, tractors, bulldozers, dump trucks, in heavy operating conditions or fuel, which vary in quality (including sour). Operating temperature range: summer oil М-10DM from minus 5°С to +30°С, winter oil М-8DM: from minus 20°С to +25°С.
Index name М-8DМ М-10DМ
Compliance with classifi cations SAE (API) 20 (СD ) 30 (СD )
Kinematic viscosity at 100°С, mm2/s 8,0–8,5 not less than 11,4
Viscosity index, not less than 102 90
Total Base Number, mg КОН/g, not less than 8,5 8,2
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
195Minus 30
220Minus 18
Sulphated ash, %, not more than 1,5
Mass fraction of active elements, %, not less than • Calcium • Zinc • Phosphorous
---
0,300,09
–
REFERENCE BOOK
20
OIL
S
Uni
vers
al m
iner
al m
otor
oils
Universal mineral motor oils
GOST 8581-78
М-8V — winter oil for medium augmented automotive diesel engines (ZIL-130, GAZ-66,51, KaVZ, KAZ, PAZ, LIAZ). Also used in a medium augmented gasoline engines of cars and trucks (replacement intervals up to 18 thousand km). Can be applied in such medium augmented automotive diesel engines as SMD-14, А-41, D-50, D-37, etc., which are running on high sulfur fuel. Operating temperature range: from minus 20°С to +25°С.
М-6z/12G1 — multigrade oil for lubrication of boosted gasoline engines of passenger cars in regions with moderate climate and air temperature ranged from minus 20°С to +45°С.
Index name M-8V М-6z/12G1
Compliance with classifications SAE (API) 20W-20 (CВ/SD) 15W-30 (SF)
Kinematic viscosity at 100°С, mm2/s 7,5–8,5 not less than 12
Dynamic viscosity at minus 15°С, mPa·s, not more than – 4500
Viscosity index, not less than 93 115
TBN, mg КОН/g, not less than 4,2 7,5
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
207Minus 25
210Minus 30
Sulphated ash, %, not more than 0,95 1,3
Mass fraction of active elements, %, not less than: • Calcium • Zinc
0,160,09
0,230,10
REFERENCE BOOK
21
OIL
S
Oils
for 2
- an
d 4-
stro
ke e
ngin
es
Oils for 2- and 4-stroke engines
TS U 23.2-36451680-137:2010
Agrinol Moto Racer 2T — low ash, mineral oil for the lubrication of modern two-stroke gasoline engines of average power, such as: chain saws, lawn mowers, boat motors, motorcycles, mopeds, etc.
Recommended ratio of the fuel mixture is: 1:40 (oil: gasoline).Agrinol Aqua Moto 2T — low ash, semisynthetic oil for the lubrication
of modern 2-stroke boat motors (including overhead) with water coolance (boats, motor boats, jet skis, jet skis), as well as engines of snowmobiles, motorcycles, chainsaws and other portable equipment with a variety of oil supply methods (by adding a gasoline or by injection through the nozzle).
Recommended ratio of the fuel mixture is: 1:50 (oil: gasoline).
Index name Agrinol Moto Racer 2T Agrinol Aqua Moto 2T
Compliance with classifi cations SAE/API /JACO/ISO/NMMA 40/ТС/FB/L-EGR/– 20/–/–/–/TC-W3
Kinematic viscosity at 100°С, mm2/s 8,0-10,0 8,5-10,0
Viscosity index, not less than 90 110
TBN, mg КОН/g, not less than 0,75 1,0
Mass fraction, %, not more than: • Water • Mechanical impurities
TracesNone
TracesNone
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200-25
90-25
Sulphated ash, %, not more than 0,1 0,1
Mass fraction of active elements, %, not less than:
• Calcium 0,02 0,03
of small machinery
Oils for 2- and 4-stroke engines REFERENCE BOOK
22
OIL
S
Oils
for 2
- an
d 4-
stro
ke e
ngin
es
TS U 23.2-36451680-137:2010
Agrinol Moto Drive 2T — low ash, semisynthetic oil for the lubrication of modern two-stroke gasoline engines of medium and high power, such as: chainsaws, snowmobiles, karts, motorcycles, mopeds, and others. Oil is recommended for use both in mixture and in separate fuel and oil supply.
Recommended ratio of the fuel mixture is:– for snowmobiles, motorcycles, etc. — 1:50 (oil: gasoline);– for lawn mowers, chainsaws — 1:40 (oil: gasoline).Agrinol Moto Drive 4T — low ash, semisynthetic engine oil designed
to lubricate the modern four-stroke engines of motorcycles, ATVs, scooters and other motor vehicles with any clutch, mobile equipment, water-cooled outboard boat engines.
Index name Agrinol Moto Drive 2T Agrinol Moto Drive 4T
Compliance with classifi cations SAE/APIISO
20/ТС +L-EGD
10W-40/SJ,SG-
Kinematic viscosity at 100°С, mm2/s 6,5-8,5 13,0-16,5
Viscosity index, not less than 120 138
TBN, mg КОН/g, not less than 1,4 9,0
Mass fraction, %, not more than: • Water • Mechanical impurities
TracesNone
TracesNone
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
80-30
205-32
Sulphated ash, %, not more than 0,1 1,5
Mass fraction of active elements, %, not less than:
• Calcium • Zink
0,04-
0,250,11
of small machinery
REFERENCE BOOK
23
OIL
S
Oils
for m
arin
e an
d lo
com
otiv
e en
gine
s
Oils for marine and locomotive engines
GOST 12337-84
М-14V2 oil is intended for use in two-and four-stroke diesel and marine diesel engines of trunk piston type, operating on distillate fuels with sulfur content up to 0,5 % (mass fraction), as well as for engines of open- pit dump trucks. Also it can be used in southern areas as summer oil, instead of М-10V2.
М-16G2TsS is intended for lubricating of the trunk piston of cylinders (high degree of forcing), crosshead (low-speed) of diesel engines with not more than 1,5 % of sulfur in fuel.
Agrinol Marine TBN 15 – marine engine oils developed for high-performance trunk piston engines of average speed, which operates on distillate or residual fuel with the content of sulfur of at most 1,5%. It is recommended for all high-performance trunk engines and reduction gears where such type of lubricant is determined by the manufacturer.
Index name М-14V2 М-16G2TsSAgrinol Marine TBN 15
Agrinol Marine TBN 15
Compliance with classifi cations SAE (API) 40 (СВ) 50 (СС) 30 (CD) 40 (CD)
Kinematic viscosity at 100°С, mm2/s 13,5–14,5 15,5–17,0 905 910
Viscosity index, not less than 85 92 9,5-12,5 13,5-16,5
TBN mg КОН/g, not less than 4,8 9,0 92 92
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
210Minus 12
220Minus 10
230Minus 20
230Minus 15
Sulphated ash, %, not more than 1,2 1,5 3,0 3,0
Emulsifi ability with water, cm3, not more than – 0,5
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than
• Critical load • Scuff index • Wear index (196 N), mm, not more than
7843630,4
8233330,4
3338230,5
0,650,050,04
REFERENCE BOOK
24
OIL
S
Cha
in S
aw O
il
Chain Saw Oil
TS U 19.2-32365441-206:2016
Special oils series Chain Saw Oil EXPERT– 68, -100, -150 is designed for lubrication of chainsaw, chain rails (tires) and the leading asterisks of all kinds of electric and gasoline-powered saws equipped with both manual and automatic lubrication system.Developed to improve the use of cutting elements chainsaws any models and classes.
Index name Chain Saw Oil EXPERT
Comply with international classifications: ISO VG 68 100 150
Kinematic viscosity at 100°С, mm2/s 60-75 90-110 148-165
Acid number, mg КОН per 1g of oil, not more thаn 1,5 1,2 1,2
Mass fraction of water no more Traces
Mass fraction of mechanical impurities 0,015
Sulphated ash, %, not more than 1,5 1,5
Open cup fl ash point, °С, not less than 210 214 220
Pour point, °С, not higher than -30 -30 -28
Density at 20°С, kg/m3, not more than 900 910 920
Tribological characteristics on four-ball machine at (20 ± 5) ° C and load of 196N
• Welding load, N, not less than • Scuffi ng index, N, not less than • Wear index mm, not more than
23237800,5
Corrosive effect on the metals, copper100 ° C, 3 h Pass
Chain Saw Oil REFERENCE BOOK
25
OIL
S
Cha
in S
aw O
il
TS U 19.2-32365441-206:2016
Special oils series Chain Saw Oil STANDARD is designed for lubrication of chainsaw, chain rails (tires) and the leading asterisks of all kinds of electric and gasoline-powered saws equipped with both manual and automatic lubrication system.
Index name Chain Saw Oil Standard
Comply with international classifications: ISO VG 68 100 150
Kinematic viscosity at 100°С, mm2/s 61,2-74,8 90-110 135-150
Acid number, mg КОН per 1g of oil, not more thаn 1,2 1,2 1,2
Mass fraction of water no more Traces
Mass fraction of mechanical impurities 0,015
Sulphated ash, %, not more than 1,5 1,5
Open cup fl ash point, °С, not less than 220 226 230
Pour point, °С, not higher than -30 -28 -26
Density at 20°С, kg/m3, not more than 900 910 920
Tribological characteristics on four-ball machine at (20 ± 5) ° C and load of 196N Wear index mm, not more than 0,5
Corrosive effect on the metals, copper 100 ° C, 3 h Pass
Color, CNT units, not more than 4 4,5 5
REFERENCE BOOK
26
OIL
S
Oils
for m
arin
e an
d lo
com
otiv
e en
gine
s
Oils for marine and locomotive engines
GOST 12337–84
М-14DTsL20, М-14DTsL30 oils are used for lubricating medium-trunk-piston marine diesel engines with a combined circulation or lubrication system and industrial engines, gearboxes, tools and other units operating on fuel with a sulfur content of 2.5-3.5%.
Index name М-14DTsL20 М-14DTsL30
Compliance with classifi cations SAE (API) 40 (CD) 40 (СD)
Kinematic viscosity at 100°С, mm2/s 13,5–15,0 13,5–15,0
Viscosity index, not less than 92 92
Total Base Number, mg КОН/g, not less than 18 27
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
220Minus 10
210Minus 10
Sulphated ash, %, not more than 3,0 4,6
Emulsifi ability with water, cm3, not more than 1,0 1,0
Mass fraction of active elements, %, not less than: • Calcium • Zinc • Phosphorus
0,650,0450,040
1,00,0450,040
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than
• Critical load • Scuff index • Wear index (196 N), mm, not more than
8333330,5
–––
Oils for marine and locomotive enginesREFERENCE BOOK
27
OIL
S
Oils
for m
arin
e an
d lo
com
otiv
e en
gine
s
GOST 12337–84
М-20Е70 oil is used for lubrication of the major low-speed marine diesel engines during the work on low-sulfur heavy fuels (with sulfur content up to 4,5%).
М-20V2F — seasonal oil for marine diesel engines of 12CHN 18/20 and CHN 16/17 type, working with extended terms of oil change in difficult conditions, conducive to the formation of high temperature deposits.
Index name М-20Е70 М-20V2F
Compliance with classifi cations SAE (API) 50 (CB) 50 (CB)
Kinematic viscosity at 100°С, mm2/s 20,0–23,0 19,0–22,0
Viscosity index, not less than 90 90
Total Base Number, mg КОН/g, not less than 70 2,8
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200Minus 12
230Minus 15
Sulphated ash, %, not more than 10,5 0,65
Emulsifi ability with water, cm3, not more than 0,3 –
Mass fraction of active elements, %, not less than: • Calcium • Zinc • Phosphorus
2,8––
0,08–
0,03
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than:
• Critical load • Scuff index • Wear index (196 Н), mm, not more than
9803920,3
8233530,32
Oils for marine and locomotive enginesREFERENCE BOOK
28
OIL
S
Oils
for m
arin
e an
d lo
com
otiv
e en
gine
s
TS U 23.2-36451680-144:2010
Agrinol M-14D2U, Agrinol М-14D2 — motor mineral oils for lubricating of marine, locomotive, stationary, transport and industrial diesel engines, as well as heavy-duty diesel engines, mining vehicles and diesel rigs requiring oils of D2 group.
Index name Agrinol М-14D2U Agrinol М-14D2
Compliance with classifi cations SAE (API) 40 (CD) 40 (СD)
Kinematic viscosity at 100°С, mm2/s 13,5–14,5
Viscosity index, not less than 85 90
Total Base Number, mg КОН/g, not less than 13,0
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
220Minus 12
230Minus 12
Sulphated ash, %, not more than 2,0 1,8
Mass fraction of active elements, %, not less than:
• Calcium • Zinc • Phosphorus
0,450,100,10
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:
• Critical load • Scuff index, • Wear index (196 N), mm, not more than
8234210,40
Oils for marine and locomotive enginesREFERENCE BOOK
29
OIL
S
Oils
for m
arin
e an
d lo
com
otiv
e en
gine
s
TS U 23.2-36451680-145:2010
Agrinol М-14V is a mineral engine oil used for lubrication of two-and four-stroke diesel engines of 2D100, D-50 types and similar to them in terms of boosting shunting and industrial locomotives
TS U 23.2-30802090-122:2009
Agrinol МТ-16P is a seasonal mineral oil for lubricating of diesel engines of B2 type vehicles and its analogs in terms of forcing the naturally aspirated diesel engines: automotive diesel engines of old models, marine, locomotive, stationary and transport naturally aspirated diesel engines.
GOST 12337–84
М-20G2 — season mineral engine oil used for lubricating of high-speed vessels, diesel and other diesel engines. Provides lubrication for two-stroke diesels of MD 23/2×30 type.
Index name Agrinol М-14B Agrinol МТ-16P М-20G2
Compliance with classifi cations SAE (API) 40 (–) 40 (СВ) 50 (СС)
Kinematic viscosity at 100°С, mm2/s 14,0±0,5 15,5–16,5 not less than 20,0
Viscosity index, not less than 85 85 85
Total Base Number, mg КОН/g, not less than 1,0 4,0 9,0
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200Minus 15
210Minus 25
235Minus 15
Sulphated ash, %, not more than 1,0 0,6–1,0 1,9
Mass fraction of active elements, %, not less than:
• Calcium • Zinc • Phosphorus
–––
–––
0,360,050,05
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:
• critical load • scuff index • wear index (196 N), mm, not more than
––
0,6
––
0,45
8233630,35
REFERENCE BOOK
30
OIL
S
Tra
nsm
issi
on o
ils
Transmission oils
TS U 23.2-30802090-120:2009
TRANSMISSION oils series consists of transmission multigrade oils, which are used for lubricating of all types of gears: cylindrical, conical, spiral bevels and hypoid gears of cars, trucks, buses, tractors; road and construction equipment.
Transmission Oil Classic SAE 80W-90 API GL-4 is intended for lubricating mechanical transmissions, cars, lorries and mobile equipment, as well as other sites where level of API GL-4 (TM-4) oil is recommended.
Transmission Silver SAE 85W-90 API GL-5, Transmission Gold SAE 80W-90 API GL-5 and Transmission Platinum SAE 75W-90 API GL-5 oils are designed for lubrication of mechanical transmissions with all types of gears, including hypoid. Can be used in driving axles and transfer boxes of passenger cars, trucks and other mobile equipment operating in the most demanding conditions, where oil of API GL-5 (ТМ-5) level is needed.
Perfomance level:Platinum SAE 75W-90 GL-5: MIL-L 2105 C/D, ZF TE-ML 08Gold SAE 80W-90 GL-5: MIL-L-2105D, MB 235.6, ZF TE-ML 05A-07A-12A-16C/D-17B, MAN 342MSilver SAE 85W-90 GL-5: MIL-L-2105D, MB 235.6, ZF TE-ML 05A-07A-12A-16C/D-17B, MAN 342MLSAE 85W-140 GL-5: MIL-L-2105D, ZF TE-ML 05A-07A-12A-16C/D-17B, MAN 342MLClassic 80W-90 API GL-4: Ford SQM-2C-9008 A, MAN 341 тип E-1/341 тип Z-1, MB 235.1, MIL
L-2105D, ZF TE-ML 16A/TE-ML 17A/TE-ML 19A
Index name
Transmission
Classic SAE
80W-90 API GL-4
Silver SAE 85W-
90 API GL-5
Gold SAE 80W-90 API GL-5
Platinum SAE 75W-
90 API GL-5
SAE 85W-140 API GL-5
Kinematic viscosity at 100°С, mm2/s 16,5 17,5 17,5 13,5 24,0
Viscosity index, not less than 95 95 95 95 95
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
200-20
210-15
200-20
185-25
220-20
Mass fraction of sulfur, %, not less than 0,8 1,0 1,0 1,0 1,0
Corrosive effect on metals Pass
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than
• Welding load • Scuff index • Wear index (196 N), not more
34794900,5
36875680,4
36875680,4
32834900,4
4136588
-
Transmission oilsREFERENCE BOOK
31
OIL
S
Tra
nsm
issi
on o
ils
TS U 23.2-36451680-153:2010
Agrinol MULTIPLEX GL-5 SAE-90 is a universal gear oil used for lubrication of reducers of rolling mills, mechanical transmissions with all types of gears including hypoid (drive axles, transfer cases, etc) of cars, trucks and tractors, metallurgical equipment, which operate under severe conditions, where oils of ТМ-5 (API GL-5) level are needed.
MULTIPLEX SAE 140 GL-5 - transmission oil for the lubrication of loaded axles and gears of all types: cylindrical, conical, spiral bevel and hypoid gear off-road vehicles, trucks, buses, tractors, road and construction equipment, operating in the most severe operating conditions that require compliance with standards API GL- 5.
Index name Agrinol MULTIPLEX GL-5 SAE-90
Agrinol MULTIPLEX SAE 140 GL-5
Kinematic viscosity, not less than • At 100°С, mm2/s • At 40°С, mm2/s
18200
24,0
Viscosity index, not less than 90 90
Acid number, mg КОН/1g, not more than 1,2 -
Color on CNT colorimeter with 15:85 dilution, CNT units, not more than 6 -
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
215Minus 25
230Minus 15
Mass fraction: • Mechanical impurities, %, not more
than • Water, %, not more than • Phosphorous, %, not less than
0,01None0,04
-
Corrosive effect on metals Pass 0,01
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than
• Critical load • Welding load • Scuff index • Wear index (196 N)
98041356000,4
3920580
Transmission oilsREFERENCE BOOK
32
OIL
S
Tra
nsm
issi
on o
ils
GOST 23652–79
Oil TAp-15V is intended for lubricating of transmissions of trucks, road construction equipment and gears (spur, spiral bevel gearings and worm-type gears where the contact stresses are up to 2000 MPa and oil temperature is up to 130 °C). In the middle climatic zone this oil is used all year-round at temperatures up to minus 25 °C.
TAD-17i oil is intended for lubricating of all types of gears (including hypoid) of cars and other mobile equipment. Multigrade oil, operates at temperatures up to minus 30 °С. The upper limit of continuous performance is 140 °C.
Index name ТАp-15В ТАD-17i
Compliance with classifi cations SAE (API) 90 (GL-3) 85W-90 (GL-5)
Kinematic viscosity, mm2/s: • At 50°С • At 100°С
–15,0±1,0
110–120not less than 17,5
Viscosity index, not less than – 100
Corrosion test (for 3 hours): • At 100°С (steel and copper plates) • At 120°С (copper plates), points, not more than
Pass–
–2с
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
185Minus 20
200Minus 25
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than:
• Scuff index • Critical load • Wear index (392 Н), mm, not more than
3283490–
36875680,40
Transmission oils in accordance with GOST 23652-79
Transmission oilsREFERENCE BOOK
33
OIL
S
Tra
nsm
issi
on o
ils
GOST 23652–79
TSp-10 oil is intended for lubricating of heavily loaded cylindrical, bevel and spiral bevel gears operating under the contact stresses up to 1500 2000 MPa and temperatures of oil in volume up to (100-110)°С.
Product is a winter oil, operational at the temperatures up to minus 45°С.TSp-15K oil is a multigrade transmission oil for lubricating of heavily loaded
cylindrical, bevel and spiral-bevel gears of KamAZ heavy-vehicles. Operates at temperatures up to minus 30°С.
TSp-14gip oil is used in hypoid gears of trucks. It is a multigrade oil, operated at the temperatures up to minus 30°С.
Index name TSp-10 TSp-15K TSp-14gip
Compliance with classifi cations SAE (API) 80 (GL-3) 90 (GL-3) 90 (GL-5)
Kinematic viscosity, mm2/s: • At 100°С, not less than 10,0 15,0±1,0 14,0
Viscosity index, not less than 90 85
Corrosion test (for 3 hours): • At 100°С (steel and copper plates) • At 120°С (copper plates), points, not more
than
Pass–
–2с
Pass–
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
128Minus 40
191Minus 25
215Minus 25
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than
• Scuff index • Critical load • Wear index (392 N)
3479470–
34795390,50
3920588–
Transmission oilsREFERENCE BOOK
34
OIL
S
Tra
nsm
issi
on o
ils
TS U 23.2-30802090-021:2002
Oil ТАp-15V is intended for lubricating of transmissions of trucks, road construction equipment and gears (spur, spiral bevel gearings and worm-type gears where the contact stresses are up to 2000 MPa and oil temperature is up to 130 °C). In the middle climatic zone this oil is used all year-round at temperatures up to minus 25 °C.
ТAD-17i oil is intended for lubricating of all types of gears (including hypoid) of cars and other mobile equipment. Multigrade oil, operates at temperatures up to minus 30 °С. The upper limit of continuous performance is 140 °C.
Agrinol ТSzp-8 oil is designed for all seasons use in in the northern regions and in winter in average climatic zones, lubricating aggregates of transmissions that have planetary gear transmissions and hydraulic control systems of some other mobile vehicles. This is transmission transport machinery, spur, helical-bevel and worm gears operating under conditions of contact stresses up to 20,000 kg/cm2.
Index name Agrinol ТАp-15В
Agrinol ТАD-17i
Agrinol ТSzp-8
Compliance with classifi cations SAE (API) 90 (GL-3) 85W-90 (GL-5) 80W (GL-3)
Kinematic viscosity at 100°С, mm2/s 15,0±1,0 18,0 7,5-8,5
Viscosity index, not less than 60 100 140
Mass fraction of sulfur, %, not less than 0,7 1,0 1,0
Corrosive effect on metals Pass
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
185-12
200-15
163-40
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:
• Welding load • Wear index (196 Н), mm, not more than
2930-
32830,40
24500,5
Agrinol Transmission oils
Transmission oilsREFERENCE BOOK
35
OIL
S
Tra
nsm
issi
on o
ils
TS U 23.2-36451680-153:2010
TSp-10 oil is intended for lubricating of heavily loaded cylindrical, bevel and spiral bevel gears operating under the contact stresses up to 1500 2000 MPa and temperatures of oil in volume up to (110)°С.
Product is a winter oil, operational at the temperatures up to minus 45°С.TSp-15K oil is a multigrade transmission oil for lubricating of heavily loaded
cylindrical, bevel and spiral-bevel gears of KamAZ heavy-vehicles. Operates at temperatures up to minus 30°С.
Agrinol TSp-14gip oil designed for lubricating hypoid trucks (mainly GAZ) and special machines as a year-round temperate climatic zone, where the recommended oil level TM-5 (API GL-5).
Index name Agrinol TSp-10
Agrinol TSp-15K
Agrinol TSp-14gip
Compliance with classifi cations SAE (API) 80W (GL-3) 90 (GL-3 ) 90 (GL-5)
Kinematic viscosity at 100°С, mm2/s 10,0 15,0±1,0 14,0
Viscosity index, not less than 90 85
Corrosive effect on metals Pass
Mass fraction of sulfur, %, not less than 1,0
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
128-30
191-15
215-15
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than
• Welding load • Wear index (196 Н)
3087-
30870,50
3479-
Transmission oilsREFERENCE BOOK
36
OIL
S
Tra
nsm
issi
on o
ils
TS U 23.2-30802090-021:2002
Agrinol Nigrol oils are used as working liquids for gearboxes, easy-loaded units of industrial equipment, open toothed gears, planetary toothed gears of cranes and excavators, toothed gears and transmission units of industrial equipment, tractors, agricultural and road-building machines, constructing devices.
Operating temperature range of Agrinol Nigrol-L:– grade A: from minus 5°С to 110°С;– grade B: from 0°С to 140°С.Operating temperature range of Agrinol Nigrol-Z:– grade А: from minus 12°С to 110°С;– grade B from minus 10°С to 140°С.
Index nameArginol Nigrol-Z Agrinol Nigrol-L
Grade A Grade B Grade A Grade B
Compliance with classifi cations SAE (API) 90 (GL-1) 90–140 (GL-1)
Appearance Homogenous black liquid
Kinematic viscosity at 100°С, mm2/s 18–22 27–34
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
140Minus 12
180Minus 10
140Minus 5
1800
Mass fraction, %, not more than: • mechanical impurities • water
0,05Traces
Corrosive effect on metals Pass
Transmission oils for industrial an obsolete equipment
Transmission oilsREFERENCE BOOK
37
OIL
S
Tra
nsm
issi
on o
ils
TS U 23.2-36451680-134:2010
Agrinol ATF ІІD is a mineral oil used in automatic gearboxes, transmissions, in power assisted steering of cars and trucks, buses, tractors, road and construction machinery, special equipment in accordance with the instructions of the manufacturers of vehicles.
Agrinol ATF ІІI is a semi-synthetic oil used in automatic gearboxes, transmissions, in power assisted steering of cars and trucks, buses, tractors, road and construction machinery, special equipment in accordance with the instructions of the manufacturers of vehicles.
Perfomance level:Agrinol ATF ІІD A-MATIC: GM Dexron IID, Mercon, Caterpillar TO-2, Volvo 97335 Agrinol ATF ІІI A-MATIC PLUS: GM Dexron IIІ, Mercon V, MAN 339 type V-1, MAN 339 type Z-2,
Caterpillar TO-2, Volvo 97340, ZF TE-ML-04D -14C, -16L, - 17L
Index name Agrinol ATF ІІD Agrinol ATF ІІI
Kinematic viscosity at 100°С, mm2/s, not less than 7,5±0,5
Viscosity index, not less than 150 170
Temperature,°С: • Open cup fl ash point, °С, not less than • Pour point, not more than
185Minus 42
175Minus 45
Corrosive effect on metals, points, not more than 1B
Sulphated ash, %, not more than 0,1
Mass fraction, %, not less than: • sulfur, %, not less than • mechanical impurities, %, not less than
0,4None
0,1None
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than
• wear index (314 N) 0,5
Automatic transmission fluid
REFERENCE BOOK
38
OIL
S
Uni
vers
al o
ils fo
r aut
omot
ive
dies
els
Universal oils for automotive diesels
TS U 23.2-36451680-137:2010
Agrinol STOU SAE 10W-30, STOU SAE 10W-40 – universal series of oils of STOU class (Super Tractor Oil Universal) for apllication in engines, including turbocharged, in mechanic transmissions and hydrosystems (hydro and hydraulic clutches) of tractors and other agricultural and building vehicles. Suit for apllication in “wetdiscbrakes” of modern special technics.
Perfomance level:Engines: АРI CG-4, ACEA E3, SAE J300 10W-30 (10W-40)MAN 271Transmission units:SAE J306 75W-80 (75W-90)ALLISON C-4, CAT TO-2/TO-4, FORD M2C159 B/C; John Deere JDM J 20 C; MF M1135, 1139, ZF TE-
ML06AHydro-systems and hydraulic clutches:ISO VG 46 / 68 / 100, DIN 51524.2/3 НLP/HVLP-D AFNOR NFE 48603 HV;
Index name STOU SAE 10W-30 STOU SAE 10W-40
Viskosity index,not less than 135
Kinematic viscosity at 100°С, mm2/s 9,3-12,5 12,5-16,3
TBN, mg КОН/g, not less than 9,0 7,5
Sulphated ash, %, not more than 1,5
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200–32
205–32
Universal oils for automotive dieselsREFERENCE BOOK
39
OIL
S
Uni
vers
al o
ils fo
r aut
omot
ive
dies
els
TS U 23.2-36451680-137:2010
Agrinol UTTO 80W, 85W – universal transmission-hydraulic oil (Universal Tractor Transmission Oil), which applied in combined driving gear (transmission/hydraulic), including hydraulic (“wet”) brakes of tractor vehicles (agricultural, road-building and other special technics). It is possible to use the product in different hydraulic mechanisms. Special additives provide noiseless operation of power unit.
Perfomance level:Transmission units:АРI GL-4SAE; J306C 80W 85W; SAE J300; 10W-30; 20W-40; ZF TE-ML 03E, 05F, 06K,17E, 21F;
Allison C3/C4; Caterpillar TO-2; John Deere JDM J 20 C; Ford M2C 134 C/D, M2C 86 B/C;Hydro-systems and hydraulic clutches:ISO VG 46 / 68 /100; DIN51524.2/3 HLP/HLP-D
Index name UTTO 80W UTTO 85W
Viskosity index,not less than 135
Kinematic viscosity at 100°С, mm2/s 9,3-12,5 12,5-16,3
TBN, mg КОН/g, not less than 9,0 7,5
Sulphated ash, %, not more than 1,5
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200–32
205–32
REFERENCE BOOK
40
OIL
S
Oils
for h
ydro
mec
hani
cal t
rans
mis
sion
s
Oils for hydromechanical transmissions
TS U 23.2-30802090-047:2005
Agrinol A oil is used for multigrade exploitation in torque converters, automatic transmissions at the environmental temperatures up to minus 35°С. Product can be used as winter oil in the hydrostatic drives of self-propelled agricultural and other machinery.
Agrinol R oil is used in systems of wheel hydrostrengthenings and hydrostatic transmissions at the environmental temperature up to minus 40°С.
TS U 23.2-36451680-165:2011
Special Oil HMT is used for multigrade exploitation in torque converters, automatic transmissions, and hydrostatic transmissions at the environmental temperatures up to minus 5°С.
Index name Agrinol A Agrinol R Special Oil HMT
Compliance with classifi cations ISO VG (ISO 6743)
32(Automatic
transmission fl uid)
32(Automatic
transmission fl uid)
32(Automatic
transmission fl uid)
Kinematic viscosity, mm2/s: • At 40°С • At 100°С
30–45not less than 6,5
17–22not more than
5,0
30–45not less than 6,5
Viscosity index, not less than 90 90 105
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
175Minus 40
163Minus 45
190Minus 40
Mass fraction, %, not more than: • Mechanical impurities • Water
0,01None
Mass fraction of active elements, %, not less than:
• Calcium • Zinc
0,160,08
0,160,8
0,160,08
Corrosive effect on metals Pass
Ash content, %, not less than 0,60 0,60 0,60
REFERENCE BOOK
41
OIL
S
Hyd
raul
ic o
ils
Hydraulic oils
TS U 23.2-30802090-067:2006
Hydraulic oil Agrinol VMGZ is used as a winter oil. In Arctic conditions it is used as а year-round working liquid in hydraulic drives and hydraulic control systems of constructing, road, logging, lifting and other machines and mechanisms exploited in the open air at the working temperature of oil from minus 55 °С up to 80 °С.
GOST 6794–75
AMG-10 oil is designed for use as a working fluid for hydraulic devices operating in the range of environmental temperatures from minus 60°С to +55 °С.
TS U 23.2-30802090-124:2009
Spindle oil Agrinol AU is intended for use in lightly loaded hydraulic systems of mobile equipment with gear and piston pumps, working under pressure up to 15 MPa and maximum oil temperature up to 100°С.
Oil supports the work of hydraulic drives in the temperature range from minus 35°С to plus 100°С.
Index name AMG-10 Agrinol VMGZ Agrinol AU
Compliance with classifi cations ISO VG ISO 6743 // DIN 51524
Designation according to GOST 17479.3
15 HL // HLPМГ-15-Б
15 HM // HLPМГ-15-В
22НН
МГ-22-А
Kinematic viscosity, mm2/s: • at 40°С, not less than • at 50°С, not less than • at minus 40°С, not more than • at minus 50°С, not more than
-10-
1250
-10
1500-
16,0–22,0-
30000-
Viscosity index, not less than 140
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
93Minus 70
135Minus 60
163Minus 45
Mass fraction, %, not more than: • mechanical impurities • water
0,003None
NoneNone
NoneNone
Mass fraction of zinc, %, not less than 0,01
Ash content, %, not more than - 0,2 0,005
Acid number, mg КОН/g, within Not more than 0,03 0,40–1,0 0,07
Low-temperature oils
REFERENCE BOOK
42
OIL
S
Pow
er o
ils
Power oils
GOST 9972–74
Turbine oils with additives TP-22, TP-30 and TP-46 are intended for lubricating and cooling bearings of such various turbo-units as steam and gas turbines, water turbines, turbocompressor machines, ship steam turbine units and other analogous types of equipment. These oils are also used as working liquids for turbo-units’ regulating systems, circulating and hydraulic systems of diverse industrial mechanisms.
GOST 10289–79
Oil for marine gas turbines (SGT) product is used for lubrication and cooling of gears and bearings of marine gas turbines.
Index name Тp-22 Тp-30 Тp-46 SGT
Compliance with classifi cations ISO VG 32 46 68 -
Kinematic viscosity, mm2/s: • At 40°С, not less than • At 50°С, not less than
28,8-35,2-
41,4-50,6-
61,2-74,8-
-7,0-9,6
Viscosity index, not less than 90 95 90 -
Acid number, mg КОН/g, within, not more than 0,05 0,5 0,5 0,02
Temperature, °С: • Flash point, not less than • Fluidity, not more than • Pour point, not more than
186-6-15
190-6-10
220-6-10
135 (in closed crucible)
--45
Ash content, % not more than - 0,005
Anti-corrosion properties, steel (copper, group) None (-) -
Demulsifi cation number, min, not more than 3,0 3,5 3,0 -
Oxidation stability: • Sediment, %, not more than • Acid number, mg КОН/g, within,
not more than
0,030,3
0,030,4
0,11,5
0,200,65
Turbine oils according to GOST 9972-74, GOST 10289-79
Power oilsREFERENCE BOOK
43
OIL
S
Pow
er o
ils
TS U 23.2-30802090-076:2007
The lubricating oil Agrinol МS-8p is intended for usage in hydraulic and lubricating and cooling systems of gas-turbine units, gas-pumping units, equipment of gas pipelines and other industrial equipment. The oil is efficient at the temperature varying from minus 40°С up to 80°С
Index name Agrinol MS-8p
Kinematic viscosity, mm2/s: • At 50°С, not less than • At minus 40°С, not less than
84000
Acid number, mg КОН/g, within, not more than 0,05
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
150Minus 55
Mass fraction, %, not more than: • Mechanical impurities • Water • Sulfur
NoneNone0,5
Corrosion on the plates after oxidation, mg/cm2, not more than:
• Steel ShH 15 • Copper М1 and М2 • Aluminum alloy АК4
None+0,2None
Oxidation resistance, not more than: • Kinematic viscosity at 50°С, mm2/s • Kinematic viscosity at minus 40°С, mm2/s • Acid number, mgКОН/g • Mass fraction of insoluble residue, %
10,055000,7
0,15
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:
• Critical load • Diameter of the wear spot ( 196N), not more than
4900,55
Power oilsREFERENCE BOOK
44
OIL
S
Pow
er o
ils
TS U 23.2-36451680-156:2010
Kompressoil VG 46, 68, 100 oil is intended for lubricating of pistons (cross-head, without cross-head, single and multistage) and rotary air compressors working permanently at 220°С on a blowing line.
Low-viscosity versions of Kompressoil VG oils are used in rotary compressors (in accordance with the recommendations of manufacturers of compressors).
Index nameKompressoil
VG 46 VG 68 VG 100
Compliance with classifi cations ISO VGDIN 51506
46VDL
68VDL
100VDL
Kinematic viscosity at 100°С, mm2 / s42,0 – 50,0
6,5 – 7,561,0 – 75,0
7,5 – 9,090,0 – 110,0
9,5 – 12,0
Viscosity index, not less than 90 90 90
Acid number, mg КОН / g, not more than 0,2 0,2 0,2
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
210Minus 20
220Minus 20
225Minus 20
Mass fraction of sulfur, %, not more than 0,3 0,5 0,5
Oxidation stability: • Sediment, %, not more than 0,02 0,02 0,02
Corrosive effect on metals Pass
Color with dilution 15 / 85, CNT units, not more than 1,5
Kompressoil VG
Power oilsREFERENCE BOOK
45
OIL
S
Pow
er o
ils
TS U 23.2-36451680-156:2010
Kompressoil VG 150, 220, 320 oil is intended for lubricating of pistons (cross-head, without cross-head, single and multistage) and rotary air compressors working permanently at 220°С on a blowing line.
Low-viscosity versions of Kompressoil VG oils are used in rotary compressors (in accordance with the recommendations of manufacturers of compressors).
Index nameVG 150 VG 220 VG 320
Compliance with classifi cations ISO VGDIN 51506
150VDL
220VDL
320VDL
Kinematic viscosity at 100°С, mm2 / s130,0 – 160,0
12,5 – 15,5200,0 – 240,0
17,0 – 20,0300,0 – 350,0
22,0 – 25,0
Viscosity index, not less than 90 90 90
Acid number, mg КОН / g, not more than 0,2 0,2 0,2
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
230Minus 20
235Minus 20
240Minus 20
Mass fraction of sulfur, %, not more than 0,5 0,5 0,5
Oxidation stability: • Sediment, %, not more than 0,02 0,02 0.02
Corrosive effect on metals Pass
Color with dilution 15 / 85, CNT units, not more than 1,5
Power oilsREFERENCE BOOK
46
OIL
S
Pow
er o
ils
TS U 23.2-30802090-017-2003
Agrinol KS-19p is oil for compressor units. It is intended for lubricating of piston and rotary compressors of average and high pressure.
GOST 9243-75
Compressor oil of selective refinement KS-19 is intended for lubrication of piston and rotary compressors as well as for blast-engines.
GOST 1861-73
Compressor oils K-12 and K-19 are produced from low-sulfur crude oils and are used for lubricating piston and rotary compressors and blowers.
Index name Agrinol KS-19p KS-19 K-12 K-19
Compliance with classifi cations ISO VG
ISO 6743/3В (DIN 51506)
220DAB (VDL)
220DAA (VB)
100/150DAA (VC)
220DAA (VC)
Kinematic viscosity at 100°С,mm2/s 18–24 18–22 11–14 17–21
Viscosity index, not less than 90 92 –Acid number, mg КОН/g, within, not more than 0,03 0,02 0,15 0,04
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
240Minus 15
260Minus 15
216Minus 25
245Minus 5
Mass fraction, %, not more than: • Mechanical impurities • Water
NoneTraces
NoneNone
0,007None
Coking, %, not more than – 0,5 0,3 0,5
Oxidation stability: • Sediment, %, not more than • Acid number, мг КОН/г, not more
than
None 0,5
None 0,5
0,25–
0,015–
Corrosive effect on metals Pass – Pass
Corrosion on plates of the lead, g/m2, not more than
– 10 –
Power oilsREFERENCE BOOK
47
OIL
S
Pow
er o
ils
TS U 23.2-36451680-149:2010
Agrinol Refoil 10КS oil is designed for lubrication of compressors of household refrigeration techniques, which is running on hydrocarbon refrigerant - isobutane (R600).
GOST 5546-86
HA-30 oil is intended for lubricating of compressors of refrigeration machines running on ammonia or carbonic acid.
HF 12-16 and HF 22-24 are used for lubricating of compressors of refrigeration machines running on freon.
Index nameAgrinol Refoil 10KS
HA-30 HF 12-16 HF 22-24
Compliance with classifi cations ISO (DIN 51503) 10 (KC) 46 (KA) 22 (KC) 32 (KC)
Kinematic viscosity, mm2 / s: • At 20°С • At 40°С • At 50°С
-8,0-12,0
-
120-150-
28-32
--
Not less than 17
--
24,5-28,4
Acid number, mg КОН / g, not more than 0,02 0,05 0,02 0,04
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than • Flocculation of oil mixed with Freon,
not more than
144Minus 57
-
185Minus 38
-
174Minus 42Minus 50
130Minus 55
-
Oxidation stability: • Sediment, %, not more than • Acid number, mg КОН / g, not more than • Ash content, %, not more than
--
0,005
0,020,5
0,004
0,0050,04
-
---
Mass fraction, not more than: • Mechanical impurities, % • Water • Water soluble acids and alkalis, %
None50-
NoneNoneNone
Compressor oils for gas-transit units
Power oilsREFERENCE BOOK
48
OIL
S
Pow
er o
ils
TS U 23.2-30802090-035:2005
Agrinol MGD-14m oil is used in gas-engine compressors. It is used for lubricating of motors and compressor parts of such types of gas-engine-compressors as 8GK, 8GKM, 10 GKM, 10GKN as well as similar units running on natural gas.
Index name Agrinol MGD-14m
Kinematic viscosity at 100°С, mm2/s, not less than 13,5–15,5
Viscosity index, not less than 90
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
220Minus 15
Mass fraction, %, not more than: • Mechanical impurities • Water • Sulphated ash
0,015Traces
0,2
Total Base Number, mg КОН/g, not less than 2
Corrosive effect on metals Pass
Oxidation stability: • Mass fraction of sediment in the oxidized oil,%, not more than • Acid number after oxidation, mg KOH/g, not more than
0,20,5
Stability according toIPO within 35h, viscosity increase at 100°С, %, not more than 60
Tribological characteristics on 4 balls machine at (20±5) °С,N, not less than:
• Scuff index • Critical load • Welding load
300784
1568
Power oilsREFERENCE BOOK
49
OIL
S
Pow
er o
ils
GOST 982–80
Transformer oils T-1500 and TK are sulfuric and solvent refined oils produced from low-sulfur crude oils. These products are used as oil circuit breakers (and in other high-voltage equipment as the primary insulating material).
Index name Т-1500 TK
Kinematic viscosity, mm2/s: • At 50°С • At 20°С • At minus 30°С
8–
1100
830–
Acid number, mg КОН/g, within, not more than 0,01 0,05
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
135Minus 45
135Minus 45
Mass fraction, %, not more than: • Mechanical impurities • Water • Phenol • Sulfur
NoneNone
––
Dielectric dissipation factor, %, not more than 0,5 (at 90°С) 2,5 (at 70°С)
Oxidation stability: • Mass fraction of sediment in the oxidized oil,%, not more than • Acid number after oxidation, mg KOH / g, not more than
None0,2
0,10,35
Тransformer oils
Power oilsREFERENCE BOOK
50
OIL
S
Pow
er o
ils
GOST 10121–76
ТSО transformer oil is used to fill transformers and other oil-filled electrical equipment.
TS U 23.2-30802090-113:2009
Agrinol GK transformer oil is used with electrical equipment of highest classes of electrical voltage.
Application temperature ranges from minus 35°С to 100°С.
Index name TSO Agrinol GK
Kinematic viscosity, mm2/s: • At 50°С • At 20°С • At minus 30°С
928
1300
9-
1200
Acid number, mg КОН/g, within, not more than 0,02 0,01
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
150Minus 45
135Minus 45
Mass fraction, %, not more than: • Mechanical impurities • Water • Water soluble acids and alkalis • Phenol • Sulfur
None-
None None0,6
NoneNone
---
Dielectric dissipation factor, %, not more than 1,7 0,5Oxidation stability:
• Mass fraction of sediment in the oxidized oil,%, not more than • Acid number after oxidation, mg KOH / g, not more than
None0,1
0,0150,1
Power oilsREFERENCE BOOK
51
OIL
S
Pow
er o
ils
TS U 23.2-30802090-126:2009
Agrinol KM-22 is intended for manufacturing of insulating impregnating compositions of voltage power cables of 1 – 35 kV with a paper soaked insulation. Main consumers of the oil are enterprises of electric industry.
Index name Agrinol KM-22
Kinematic viscosity at 100°С, mm2/s, not less than 22,0
Acid number, mg КОН/g, within, within 0,03
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
270Minus 10
Mass fraction, %, not more than • mechanical impurities • ash • water
None0,007Traces
Coking ability, %, not more than 0,6
Dielectric strength at (25 ± 10) °С and with frequency of the AC 50 Hz, MV/M, not less than 15
Volume resistivity at 100 °C and a voltage more than 100 V, Ohm·m, not less than
• in place of manufacturing • in place of consumption
2,0*1010
1,5*1010
Cable oils
REFERENCE BOOK
52
OIL
S
Indu
stria
l oils
Industrial oils
The last tendencies of continuous improvement of gearboxes and hydrodrives have special requirements for circulating oils used in machinery, commercial vehicles, special equipment and other branches of modern industry. Therefore “Agrinol” company extended its industrial line of PREMIUM-class hydraulic oils with series of zinc-free Hydroil Ultra HM oils and Agrinol Hydraulic Lift series, which provide reliable performance of hydraulic drives.
A series of Highrate XP gear oils consists of high quality oils for lubrication of heavy industrial gearboxes. Its high bearing capacity and antifriction characteristics offer exceptional performance in gears and other industrial nodes, provide equipment operation under increased flooding, high loads and temperatures.
The use of PREMIUM-series circulating oils is mostly justified in equipment, that operates at high temperatures, extreme temperature changes, cyclic loads, round the clock operation cycle.
Industrial oilsREFERENCE BOOK
53
OIL
S
Indu
stria
l oils
TS U 23.2-30802090-114:2009
Hydroil HM-10, -22, -32, -46, -68, -80 oils are used as a working liquid for hydraulic actuators, hydraulic transmissions, and circulating oil systems of different units, low-and moderate gears and worm gears, variable, electromagnetic, and gear couplings, bearing units, sliding guides and bearings, and other sites of the machinery of modern industrial equipment. Products does not contain chlorine compounds.
Index nameHydroil HM
10 22 32 46 68 80
Compliance with classifi cations ISO VG ISO 6743 // DIN 51524.2
10HM//HLP
22HM//HLP
32HM//HLP
46HM//HLP
68HM//HLP
80HM//HLP
Kinematic viscosity at 40°С, mm2 / s 8-14 18-26 28-36 42-50 61-75 76-85
Viscosity index, not less than 108 100 98 97 94 92
Acid number, mg КОН / g, within 0,7
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
160-30
170-27
190-24
200-24
210-24
215-20
Ash content, %, not more than 0,2
Color with dilution 15 / 85, CNT units, not more than 1,0 1,5
Mass fraction of sulfur, %, not more than 0,5 0,8
Hydraulic oils of premium group
Industrial oilsREFERENCE BOOK
54
OIL
S
Indu
stria
l oils
TS U 23.2-30802090-114:2009
Hydroil HM-100, -120, -150, -200, -270, -330 oils are used as a working liquid for hydraulic actuators, hydraulic transmissions, and circulating oil systems of different units, low-and moderate gears and worm gears, variable, electromagnetic, and gear couplings, bearing units, sliding guides and bearings, and other sites of the machinery of modern industrial equipment. Products does not contain chlorine compounds.
Index nameHydroil HM
100 120 150 200 270 330
Compliance with classifi cations ISO VG ISO 6743 // DIN 51524.2
100HM//HLP
120HM//HLP
150HM//HLP
200HM//HLP
270HM//HLP
330HM//HLP
Kinematic viscosity at 40°С, mm2/s: 90-110 110-125 148-165 186-205 265-280 320-348
Viscosity index, not less than 91 90 90 90 90 90
Acid number, mg КОН/g, within, within 0,7
Temperature, °С: • Open cup fl ash point, °С, not
less than • Pour point, not more than
220-18
220-15
225-15
230-15
230-15
240-15
Ash content, %, not more than 0,2
Color with dilution 15:85, CNT units, not more than 1,5 2,0
Mass fraction of sulfur, %, not more than 0,8 1,0
Hydraulic oils of premium group
Industrial oilsREFERENCE BOOK
55
OIL
S
Indu
stria
l oils
TS U 23.2-36451680-155:2010
Agrinol Hydraulic Lift oils are designed for use as working fluids for hydraulic drives, hydraulic transmissions and circulating oil systems of different industrial units and machinery operating under extreme loads (pressures above 25 MPa).
Index nameHydraulic Lift
22 32 46 68 100
Compliance with classifi cations ISO VGISO 6743 // DIN 51524.2
22HM//HVLP
32HM//HVLP
46HM//HVLP
68HM//HVLP
100HM//HVLP
Kinematic viscosity at 40°С, mm2 / s: 18-26 28-36 41-51 61-75 90-110
Viscosity index, not less than 130
Acid number, mg КОН / g, within 0,5-1,0
Temperature, °С: • Open cup fl ash point, °С, not less
than • Pour point, not more than
160-40
170-40
180-40
190-38
200-38
Ash content, %, not more than 2,0
Color with dilution 15:85, CNT units, not more than 4,5 5,0 5,5 5,5 6,0
Mass fraction of water, %, not more than None
Mass fraction of mechanical impurities, %, not more than
None
Corrosive effect on metals Pass
Industrial oilsREFERENCE BOOK
56
OIL
S
Indu
stria
l oils
TS U 23.2-36451680-155:2010
Oil Hydroil HM Ultra is used as the working fluid for hydraulic actuators, hydraulic transmissions and circulating oil systems of different units, low-and moderately loaded gearboxes and worm gears, CVTs, electromagnetic clutches and gear, bearing units, sliding and rolling rails and the other nodes in the machinery of modern industrial equipment.
For hydraulic systems, which cannot contain Zn-based additives.
Index nameHydroil HM Ultra
22 32 46 68 100
Compliance with classifi cations ISO VGISO 6743 // DIN 51524.2
22HM//HLP
32HM//HLP
46HM//HLP
68HM//HLP
100HM//HLP
Kinematic viscosity at 40°С, mm2 / s: 18-26 28-36 42-50 61-75 90-110
Viscosity index, not less than 100 100 100 95 91
Acid number, mg КОН / g, within 0,3
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
170-30
190-30
205-30
210-25
220-20
Ash content, %, not more than 0,1
Color with dilution 15 : 85, CNT units, not more than 1,0 1,5
Tribological characteristics on 4 balls machine at (20±5) °С, not less than:
• Diameter of the wear spot (196 Н), mm, 0,4
Zinc-free hydraulic oils of premium group
Industrial oilsREFERENCE BOOK
57
OIL
S
Indu
stria
l oils
TS U 23.2-30802090-102:2009
Highrate XP oil series is designed for the lubrication of all types of toothed, worm and helical gears and gear units with closed circulatory systems of lubrication. Product also can be used for the lubrication of various industrial spray equipment: metal cutting and woodworking machines, presses, casting and molding machines, rolling mills, mixers, dryers, extruders, fans, crushers, pumps, conveyors, elevators, lifts, rotary kilns, calenders, machines for paper production, coal combines, etc.
In ship equipment oil is used to lubricate gears, centrifuges, winches, windlasses, cranes, rotating machinery, pumps, hoists and lifting equipment of steering mechanism.
Index nameHighrate XP
68 100 150 220 320 460 680
Compliance with classifi cations ISO VG DIN 51517.3
68CLP
100CLP
150CLP
220CLP
320CLP
460CLP
680CLP
Kinematic viscosity at 40°С, mm2 / s: 61-75 90-110 140-
160190-240
300-350
420-510
610-750
Viscosity index, not less than 100 100 97 94 92 90 90
Acid number, mg КОН / g, within 2,0 2,0 2,5 3,0 3,0 3,5 3,5
Temperature, °С: • Open cup fl ash point, °С, not
less than • Pour point, not more than
210
-24
220
-24
225
-24
230
-18
230
-15
240
-12
245
-12
Mass fraction, %, not more than: • Mechanical impurities • Water
0,01Traces
0,01Traces
0,01Traces
0,02Traces
0,03Traces
0,03Traces
0,05Traces
Tribological characteristics on 4 balls machine (20±5)°С:
• Scuff index, Н, not less than • Index of wearout (196Н), mm,
not more than
3920,45
3920,45
3920,45
4900,45
4900,40
4900,45
4900,45
Gear oils premium group
Industrial oilsREFERENCE BOOK
58
OIL
S
Indu
stria
l oils
TS U 23.2-36451680-166:2010
Special Oil ART gear oils are designed for lubrication of all types of toothed, worm and helical gears of various industrial equipment: metal cutting and woodworking machines, hammers, presses, casting and molding machines, winches, rolling mills, overhead cranes, conveyors, elevators, lifts, rotary cement ovens, calenders, equipment for the manufacture of paper, coal combines, textile and spinning machines and other equipment where high loads do not allow using of oil without additives.
Index name Special Oil ART
Compliance with classifi cations ISO VG DIN 51517.3
68 100 150 220 320 460 680
68CLP
100CLP
150CLP
220CLP
320CLP
460CLP
680CLP
Kinematic viscosity at 40°С, mm2 / s: 61-75 90-
110140-160
200-240
300-340
430-490
650-710
Viscosity index, not less than 100
Acid number, mg КОН / g, not more than 0,05
Color with dilution 15 / 85, CNT units, not more than 3,0 4,0 5,0 6,0
Temperature, °С: • Open cup fl ash point, °С, not
less than • Pour point, not more than
210-20
220-18
240-15
250-12
Mass fraction, %, not more than: • Mechanical impurities • Water
0,01Traces
0,015Traces
0,02Traces
Stability against oxidation: • Changes in viscosity at 40оС, %,
not more than • Changes in acid number, mg
КОН / g, not more than
3
0,15
Tribological characteristics on 4 balls machine at (20±5) °С,N, not less than
• Scuff index, N, not less than • Index of wearout (196Н), mm,
not more than
4900,5
Industrial oilsREFERENCE BOOK
59
OIL
S
Indu
stria
l oils
TS U 23.2-30802090-097:2008
Industrial oils Agrinol I100PV are intended for lubricating of liquid friction bearings of roller mills, equipped with circulating lubrication systems with long pipelines and branching, as well as with the oil line of small diameter, where ingress of water is possible.
The main consumers of oil are companies of steel industry.
Index name Agrinol İ100PV Agrinol İ100PVs
Compliance with classifi cations ISO VG DIN 51517.1 // 51517.2 100 C, CL 100 C, CL
Kinematic viscosity, mm2/s:• At 40°С• At 100°С
90,0-110,010,0-12,0
Viscosity index, not less than 95
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
205-10
Mass fraction, %, not more than:• Mechanical impurities• Water• Sulfur
0,01Traces0,35
0,01Traces
0,6
Acid number, mg КОН / g, not more than 0,05 0,1
Demulsifi cation number, min., not more than 13
Stability against oxidation, not more than: • Increase in Acid number, mg КОН/g,
withinStability against oxidation, not more than:
0,30 0,50
For rolling mills
Industrial oilsREFERENCE BOOK
60
OIL
S
Indu
stria
l oils
GOST 12672–77
PS-28 is an oil, intended for lubrication of heavily loaded rolling mills with a circulating lubrication systems (other than liquid friction bearings).
TS U 23.2-30802090-011:2002
Agrinol PS-20 and Agrinol PS-28z oils are used as lubricating oils for circulating greasing of systems of rolling mills, reducers, rolling equipment units of average and heavy loading, equipment of tyre factories etc. (except bearings of fluid friction).
Index name PS-28Agrinol PS-20 Agrinol PS-28z
Mark A Mark B Mark A Mark B
Compliance with classifi cations ISO VG DIN 51517.1
460CV
320C
460C
Kinematic viscosity at 100°С, mm2/s, not less than 26-30 18-23 26-31
Viscosity index, not less than 80 85 85
Acid number, mg КОН / g, not more than 0,02 0,03 0,04 0,02 0,04
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
250-10
250-12
250-12
Mass fraction, %, not more than:• Mechanical impurities• Water
NoneNone
Mass fraction of sulfur, %, not more than 1,5 0,6 1,0 0,7 1,0
Coking ability, %, not more than - 0,8 0,8
Corrosive effect on metals Pass
Industrial oilsREFERENCE BOOK
61
OIL
S
Indu
stria
l oils
TS U 23.2-36451680-147:2010
Agrinol İNSp oil series is designed for lubrication of sliding and rolling machine tools, heavy gears of drive screws of especially high precision with program control, which require uniformity of the slow movement, accuracy and sensitivity of the displacement tables.
Oil Agrinol INSp-110 is designed for the lubrication of slideways of vertical and horizontal slideways with vertical faces of large area for gear and worm gears, ratchet mechanisms.
Index name Agrinol İNSp-20
Agrinol İNSp-40
Agrinol İNSp-65
Agrinol İNSp-110
Compliance with classifi cations ISO VG (ISO 6743) 32 (G) 68 (G) 100 (G) 220 (G)
Compliance of brands with oils-equivalents - İ-N-E-68 İ-N-E-100 İ-N-E-220
Kinematic viscosity at 40°С, mm2 / s: 20-30 50-70 100-110 175-200
Acid number, mg КОН / g, not more than 2,0
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
190-20
210-15
Mass fraction of water, %, not more than Traces
Color, CNT units, not more than 6,0 6,5 7,0
Ash content, %, within 0,15-0,25
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than• Scuff index• Critical load• Welding load
286720
1960
333780
2200
355872
2200
3728722450
Oils for slideways
Industrial oilsREFERENCE BOOK
62
OIL
S
Indu
stria
l oils
TS U 23.2-30802090-008:2002
Agrinol PZhT oil series is designed for lubrication of horizontal and vertical liquid friction bearings of rolling mills equipped with circulating systems with pipe-lines of various lengths and branching with possible irrigation.
Index name Agrinol PJT-46
Agrinol PJT-220
Agrinol PJT-460
Agrinol PJT-460U
Compliance with classifi cations ISO VG DIN 51517.1, 51517.2 46 C, CL 220 C, CL 460 C, CL 460 C, CL
Kinematic viscosity at 40°С, mm2 / s: 42-50 200-240 420-510 414-506
Viscosity index, not less than 95 90 90 95
Acid number, mg КОН / g, not more than 0,05 0,05 0,05 0,35
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
180-10
220-10
240-10
250-15
Coking ability, %, not more than 0,2 0,5 1,0 1,0
Demulsibility: • Time of emulsion separation, min, not more
than• Amount of layers: oil-water-emulsion,cm3
2042-36-2
2042-36-2
3042-36-2
1542-36-2
Stability against oxidation, not more than: • Viscosity change, %• Acid number change, mg КОН/g
50,1
100,15
100,4
100,4
Mass fraction of sulfur, %, not more than 0,6 0,6 0,6 0,5
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:
• Wearout index (196Н), mm, not more than • Welding load
0,75-
0,75-
0,75-
0,42067
Oils for liquid friction bearings
Industrial oilsREFERENCE BOOK
63
OIL
S
Indu
stria
l oils
GOST 6411–76
Heavy cylinder oils – petroleum oils, are intended for lubricating of the reciprocating steam engines of different purposes, working in superheated steam (C-38 up to 350°С, C-52 up to 400°С) under heavy loads and low speeds.
Index name Cylinder oil 38 Cylinder oil 52
Kinematic viscosity at 100°С, mm2/s, not less than 32-50 50-70
Viscosity index, not less than 60 80
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
300-8
310-5
Mass fraction, %, not more than:• Mechanical impurities• Water• Water soluble acids and alkalis
None0,05None
0,070,05None
Acid number, mg КОН / g, not more than 0,4 0,2
Coking ability, %, not more than 2,5
Ash content, %,not more than 0,015 0,01
Corrosive effect on metals Pass
Industrial oilsREFERENCE BOOK
64
OIL
S
Indu
stria
l oils
TS U 23.2-30802090-013:2003
Agrinol МS-20 oil does not contain active additives. It is intended for the usage in industrial equipment of rolling mills, reducers and other equipment of metallurgical, mining, woodworking enterprises. For terrestrial applications.
Agrinol МS-20p and Agrinol МS-20ps oils are generally used as lubricating oils in those cases when high requirements to exploitation properties, especially for anti-deterioration and washing properties of oils are necessary.
Agrinol MS-20gk is intended for use as grease in the lubricating system of gas motor compressors 10GKNA, MK8 and / or in other similar units. Oil consumers are enterprises of metallurgy, mining, mining and timber industries, paper manufacturing companies.
Index name Agrinol MS-20
Agrinol MS-20p
Agrinol MS-20ps
Agrinol МS-20gk
Kinematic viscosity at 100°С, mm2/s, not less than 20,5 20 20 20,5
Viscosity index, not less than 85 85 85 85
Acid number, mg КОН / g, not more than 0,03 0,04 0,05 0,1
TBN, mg КОН/g, not less than - Not less than 0,9
Not less than 1,5
Not less than 0,9
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
240-13
230-15
230-15
250-15
Coking of oils, %, not more than 0,3 0,3 0,5 0,3
Sulphated ash, %,not more than - 0,25 0,25 -
Mass fraction, %:• Mechanical impurities, not more than• Water, not more than• Sulfur in base oil, not more than• Calcium, not less than
NoneTraces
0,7-
0,01None0,7
0,08
0,015None1,00,1
NoneNone0,5-
General purpose oils
Industrial oilsREFERENCE BOOK
65
OIL
S
Indu
stria
l oils
GOST 20799–88
Industrial oils I-5А, I-8А, I-12А, I-12А1 are refined distillate and residual oils or it’s mixtures without any additives. These oils are used for machines and mechanisms of industrial equipment that does not impose specific requirements to anti-oxidation and anti-corrosion properties of oils. These products can also be used as hydraulic liquids.
Index name İ-5A İ-8A İ-12A İ-12A1
Kinematic viscosity at 40°С, mm2 / s: 6-8 9-11 13-17 13-17
Acid number, mg КОН / g, not more than 0,02 0,02 0,02 0,02
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
140-18
150-15
170-15
165-30
Mass fraction, %, not more than:• Mechanical impurities• Water
• Solvents in refi ned oils
NoneTracesNone
Mass fraction of sulfur, %, not more than 1,0 1,0 1,0 1,0
Ash content, %, not more than 0,005 0,005 0,005 0,005
Stability against oxidation: • Increase of Acid number, mg КОН/g, with-
in, not more than • Increment of resins, %, not more than
0,201,5
0,201,5
0,201,5
0,201,5
Color, CNT units, not more than 1,0 1,5 1,5 2,5
Industrial petroleum oils
Industrial oilsREFERENCE BOOK
66
OIL
S
Indu
stria
l oils
TS U 23.2-30802090-061:2006
Industrial oils I-20А, I-30А, I-40А, I-50А are refined distillate and residual oils or it’s mixtures without any additives. These oils are used for machines and mechanisms of industrial equipment that does not impose specific requirements to anti-oxidation and anti-corrosion properties of oils. These products can also be used as hydraulic liquids.
Index name I-20А I-30А I-40А I-50А
Kinematic viscosity at 40°С, mm2/s 29–35 41–51 61–75 90–110
Acid number, mg КОН/g, within, not more than 0,03 0,05 0,05 0,05
Temperature, °С: • Open cup fl ash point, °С, not less than • Pour point, not more than
200- 15
210- 15
220- 15
225- 15
Mass fraction, %, not more than: • Mechanical impurities • Water • Solvents in refi ned oils
NoneTracesNone
Mass fraction of sulfur, %, not more than 1,0 1,0 1,1 1,1
Ash content, %, not more than 0,005
Stability against oxidation: • Increase of Acid number, mg КОН/g,
within, not more than • Increment of resins, %, not more than
0,30
2,0
0,40
3,0
0,40
3,0
0,40
3,0
Color, CNT units, not more than 2,0 2,5 3,0 4,5
Heat-treatment oilsREFERENCE BOOK
67
OIL
S
Hea
t-tr
eatm
ent o
ils
TS U 23.2-30802090-023:2004
Agrinol MZ-8 is used for heat-treatment of components of medium - carbon and cemented steels.Agrinol MZ-16 is used for heat-treatment steel parts in the temperature range: 30 … 70°C.Agrinol MZ-38 is used for heat-treatment steel parts in the temperature range: 50 … 100°C.Agrinol MZ-90 is used for heat-treatment steel parts in the temperature range: 70 … 140°C.Agrinol MZ-120 is used for heat-treatment steel parts in the temperature range: 120 … 180°C.
Index name Agrinol MZ-8
Agrinol MZ-16
Agrinol MZ-38
Agrinol MZ-90
Agrinol MZ-120
Kinematic viscosity at 40°С, mm2 / s: 8-11 20-24 25-36 120-160 190-250
Acid number, mg КОН / g, not more than 0,5 0,5 0,5 0,5 0,5
Temperature, °С:• Open cup fl ash point, °С, not less
than• Pour point, not more than
140
-25
160
-15
180
-15
210
-12
235
-12
Mass fraction, %, not more than:• Mechanical impurities• Water
NoneNone
Coking ability, %, not more than 0,2 0,3 0,4 0,4 0,4
Oxidation stability, not more than: • Changes in viscosity, %• Acid number, mg КОН / g, not more
than
50,1
100,15
100,2
100,2
100,2
Heat-treatment oilsREFERENCE BOOK
68
OIL
S
Hea
t-tr
eatm
ent o
ils
TS U 23.2-30802090-074:2008
Heat-treatment oils Agrinol MZM possesses elevated antioxidant properties and are used for hardening of metals.
Index name Agrinol MZM-16
Agrinol MZM-26
Agrinol MZM-120
Kinematic viscosity at 50°С, mm2/s: 14,5-19,0 23,5-27,0 109,0-120,0
Viscosity index, not less than - 85 85
Acid number, mg КОН / g, not more than 0,01 0,01 0,02
Saponifi cation number, mg КОН/g, not more than 0,05
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
170-12
200-12
240-12
Coking ability, %, not more than 0,15 0,2 0,5
Color, CNT units, not more than 3 5 7
Mass fraction, %, not more than:• Mechanical impurities• Water
0,01Traces
0,01Traces
0,01Traces
Oxidation tests: • Weight loss, %, not more than • Kinematic viscosity at 50°С, mm2/s, not more than • Coking, %, not more than • ownward change the fl ash point in closed crucible,
°С, not more than
1022,50,30
1030,50,40
3134,00,95
0
Heat-treatment oilsREFERENCE BOOK
69
OIL
S
Hea
t-tr
eatm
ent o
ils
TS U 23.2-30802090-082:2009
Agrinol Termol heat-treatment oil is designed for quench cooling of steel products made of low-alloy and alloy steels, in order to obtain high hardness values, of the required structure and clean surface.
Index name Agrinol Termol
Kinematic viscosity at 40°С, mm2 / s: 25-36
Acid number, mg КОН / g, not more than 0,5
Flash point in open crucible, °С, not less than 180
Coking ability, %, not more than 0,25
Color, CNT units, not more than 7
Mass fraction, %, not more than:• Mechanical impurities• Water
0,026Traces
Oxidation resistance (oxidized oil properties): • Weight loss, %, not more than • Kinematic viscosity at 40°С, mm2/s, within • Coking, %, not more than • Flash point in open crucible, °С, not less than
724-400,45180
Heat-treatment oilsREFERENCE BOOK
70
OIL
S
Hea
t-tr
eatm
ent o
ils
ТУ У 23.2-30802090-090:2008
Oil Agrinol AMT-300 is designed for use as a coolant in closed systems of production, which avoids contact with hot air.
The maximum temperature of the oil Agrinol AMT-300 under the intense forced circulation is not more than 280°C.
Наименование показателя АМТ-300Kinematic viscosity at 100°С, mm2/s, not less than: 5,9
Acid number, mg КОН per 1g of oil, not more than 0,03
Temperature,°С: • open cup flash point, °С, not lower than • auto-ignition point, minimum, not less than • pour point, °С, not higher than
175285–30
Mass fraction, %, not more than: • of mechanical impurities • of water
NoneNone
Color, CNT units, not more than 6
The refractive index, not less than 1,54
Fractional composition,°C, not less than: • 5% (of volume) boil over • 95% (of volume) boil over
330475
Density at 20°С, kg/m3, not more than 960
Heat-treatment oilsREFERENCE BOOK
71
OIL
S
Hea
t-tr
eatm
ent o
ils
TS U 23.2-30802090-031:2006
Vacuum petroleum oils of Agrinol VM series are used as the working fluid for mechanical vacuum pumps.
Agrinol VМ-1 oil is used as a working liquid in high-vacuum steam-jet pumps of BN-3 series, which work at the residual pressure from 1*10-3 to 1*10-6 mm of mercury.
Agrinol VМ-3 is used as a working liquid in high-production oil-vapor booster pumps which work at the residual pressure from 1*10-2 to 1*10-4 mm of mercury.
Agrinol VМ-4 oil is used as a working liquid in mechanical vacuum pumps with oil seal.
Index name Agrinol BM-1
Agrinol BM-3
Agrinol BM-4
Kinematic viscosity, mm2/s: • At 20°С • At 100°С
60-70-
8-11-
48-578-11
Acid number, mg КОН / g, not more than 0,2
Temperature, °С:• Open cup fl ash point, °С, not less than• Open cup fl ash point, °С, not less than• Pour point, not more than
230-
-12
150-
-12
235205-15
Color, CNT units, not more than 0,5 3,5 7,0
Fractional composition of oil, °С:• Temperature of the beginning of the distillation, not
less than• 90% of the oil distilled at a temperature not higher
than• The end of the boil, not more than
-
-
-
95
175
-
370
-
515
Vapor pressure at 20°С, Pa, not more than 5,3·10-6 1,33·10-2 5,3·10-3
Density at 20°С, kg/m2, not more than 900 890 908
Vacuum oils
Heat-treatment oilsREFERENCE BOOK
72
OIL
S
Hea
t-tr
eatm
ent o
ils
TS U 23.2-30802090-031:2006
Agrinol VM-5 oil is used as the working fluid in a high-vacuum steam jet pumps, which operate at a residual pressure of 1*10-3 to 1*10-7 mm Hg. of Art.
Agrinol VM-6 used as a lubricating material and seal for piston backing pumps, working at a residual pressure of 1*10-3 mm Hg. of Art.
Agrinol VM-11 oil is used as the working fluid in a high-performance steam booster, auxiliary and steam-jet and special fore-vacuum pumps.
Index name Agrinol BM-5
Agrinol BM-6
Agrinol BM-11
Kinematic viscosity, mm2/s: • At 20°С, not more than • At 50°С, not more than • At 100°С, not more than
-60,0-74,0
-
220408
-12,5-15,8
-
Acid number, mg КОН / g, not more than 0,2
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
230-12
216-10
170-12
Color, CNT units, not more than 0,5 4,5 0,5
Fractional composition of oil, °С:• The temperature of the beginning of the
distillation, not less than• 90% of the oil distilled at a temperature not
higher than
-
-
125
220
80
175
Vapor pressure at 20°С, Pa, not more than Not more than
2,7·10-5
Not more than
4,0·10-4
6,7·10-3 - 1,3:10-4
Density at 20°С, kg/m2, not more than 900 890 890
Oil heat transfer fluid
Heat-treatment oilsREFERENCE BOOK
73
OIL
S
Hea
t-tr
eatm
ent o
ils
TS U 23.2-30802090-050:2006
Agrinol MP and Agrinol MP Plus flushing oils are designed for irrigation of automotive engine lubrication systems without disassembly (while replacement of oil).
TS U 23.2-30802090-080:2008
Flushing liquid Agrinol MPT-2M is used for flushing of lubrication systems of diesel engines (diesel, marine, automotive, road and construction equipment, etc.), as well as gasoline engine cars and trucks without disassembly while fluid replacement.
Index name Agrinol MP Agrinol MP Plus Agrinol MPT-2m
Kinematic viscosity at 50°С, mm2/s: 9-12 12-23 18-22
Temperature, °С:• Open cup fl ash point, °С, not less
than• Pour point, not more than
140
-15
140
-15
160
-15
Mass fraction, %, not more than:• Mechanical impurities• Water• Sulphated ash
0,01Traces
1,2
0,01Traces
1,2
0,015Traces
0,5
Mass fraction of active elements, %, not less than: • Calcium• Zinc
0,20,1
0,2Not specifi ed
--
TBN, mg КОН/g, not less than Not specifi ed 4,0 -
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:
• Wearout index (196 Н), mm, not more than
• Welding load • Scuff index
0,4
––
Not specifi ed
––
-
2067398
Flushing oils
Heat-treatment oilsREFERENCE BOOK
74
OIL
S
Hea
t-tr
eatm
ent o
ils
GOST 10877–76
Conservation oil K-17 is used for long-term protection of ferrous and nonferrous metals (as well as the mechanisms that are stored under cover) against atmospheric corrosion.
TS U 23.2-30802090-111:2009
Agrinol Gun Oil VO and Agrinol Gun Oil RG oils are designed for short-term protection of metal surfaces from corrosion and as lubricating oils for unloaded nodes.
Temperature of application: Agrinol Gun Oil VO — above 5 °C, Agrinol Gun Oil RG — up to minus 50 °C.
TS U 23.2-30802090-111:2009
Conservation oil Anticor-270 is intended for long-term protection against corrosion inside and outside surfaces of mechanical engineering products, rolled steel, semi-finished products and parts made of ferrous metals and their alloys, which are stored under cover or in the package.
Index name Agrinol Gun Lodge VO
Agrinol Gun Lodge RG К-17 Anticor-270
Kinematic viscosity, mm2/s: • At 100°С, not less than • At 50°С, not less than • At minus 50°С, not more
than
9,060,0
–
–6,0
1500
15,5–21,0––
–27-35 (40°С)
–
Pour point, °С, not more than – Minus 60 Minus 22 Minus 10
Mass fraction, %, not more than:
• Mechanical impurities • Water • Free alkalis in NaOH
equivalent
0,05None
–
0,07None0,05
–Traces
–
Ash content, % – 1,35–2,40 –
Protective properties –0 (%, area
of corrosion damage)
Pass Pass
Conservative oils
Heat-treatment oilsREFERENCE BOOK
75
OIL
S
Hea
t-tr
eatm
ent o
ils
TS U 24.6-30802090-106:2008
Oil-divider Form Divider is used as a release agent in continuous casting machines for rolled metal, also used in the manufacturing of polygon profiles by hot continuous casting.
Index name Form Divider Form Divider M
Kinematic viscosity, mm2/s: • At 40°С • At 100°С, not less than
45-657,5
40-807,5
Acid number, mg КОН / g, not more than 0,5 1,5
Temperature, °С:• Open cup fl ash point, °С, not less than• Pour point, not more than
230-12
230-12
Mass fraction, %, not more than:• Mechanical impurities• Water• Sulfur
0,015Traces
1,0
0,015Traces
1,0
Color, CNT units, not more than 5 6
Coking ability, %, not more than 0,15 0,15
Saponifi cation number, mg КОН/g, not more than 50-65 45-70
Density at 20°С, kg/m2, not more than 900 930
Release agent Form Divider
Heat-treatment oilsREFERENCE BOOK
76
OIL
S
Hea
t-tr
eatm
ent o
ils
GOST 1805–76
Mineral sulfur-purificated instrumental oil MVP is used for lubrication of control and measuring devices, (working in temperature range from minus 60 °С to 110 °С), for filling the pneumatic shock absorbers with petroleum and in the process of lubricants manufacture.
GOST 18375-73
Lubricating oil 132-08 is designed for lubrication of bearings in various devices and friction units of machines, operating in temperature range from minus 65-70 °С to plus 70 °С.
Index name MVP 132-08Kinematic viscosity, mm2/s:
• At 20°С • At 50°С • At minus 50°С, not less than
-6,5-8,0
-
47-55-
2200
Acid number, mg КОН / g, not more than 0,03 0,15
Temperature, °С:• Open cup fl ash point, °С, not less
than• Pour point, not more than
125-60
173-70
Mass fraction, %, not more than:• Mechanical impurities• Water• Water soluble acids and alkalis
NoneNoneNone
None0,005
-
Ash content, %,not more than 0,005 -
Color, CNT units, not more than 1,5 -
Instrumental oils
REFERENCE BOOK
79
Grea
se
Along with traditional lubricant materials, new industrial grease developments of “Agrinol” company are able to provide the operation of mechanisms for many different conditions: shock loads, high speeds, high humidity, extreme temperatures, etc.
Our researches and developments in such areas as friction, wearing and lubrication always take the needs of our clients on economic and environmental optimization into account.
High-performance lubricants, both standard and exclusive, must be selected specifically according to their tasks. No matter how unfavorable conditions of the working environment are, you will surely find a decent Agrinol lubricant suitable for the solution of your task.
Grease
REFERENCE BOOK
80
Grea
se
Along with traditional lubricant materials, new industrial grease developments of “Agrinol” company are able to provide the operation of mechanisms for many different conditions: shock loads, high speeds, high humidity, extreme temperatures, etc.
Our researches and developments in such areas as friction, wearing and lubrication always take the needs of our clients on economic and environmental optimization into account.
High-performance lubricants, both standard and exclusive, must be selected specifically according to their tasks. No matter how unfavorable conditions of the working environment are, you will surely find a decent Agrinol lubricant suitable for the solution of your task.
REFERENCE BOOK
81
Grea
se
TS U 30802090.001-2000
Agrinol Solidol G greases can be used as summer and winter lubricants in almost all industrial mechanisms, friction units of vehicles, agricultural equipment, hand tools, in rolling and sliding bearings, hinges, screw and chain drives, low-speed gearboxes.
Index nameAgrinol Solidol
G-0 G-1 G-2 G-3
Compliance with classifi cations NLGIDIN 51502
0G0C-25
1K1C-25
2 / 3K 2 / 3 C-25
3K3C-25
Appearance Homogenous ointment with a smooth texture from light yellow to dark brown color.
Thickener Са
Operating range, min…max, °С –25 … +65
Dropping point, °С, not less than 90 90 93 95Penetration at 25°С, mm·10−1 340 – 385 295 – 350 230 – 300 200 – 245
Shear strength at 50°С, Pa, not less than 100 120 150 200
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than
230 260 330 370
Colloid stability, % of secreted oil, not more than 13 12 11 10
* The index is determined by the manufacturer prior to the introduction of filler
General-purpose lubricantsfor standard temperatures
REFERENCE BOOK
82
Grea
se
GOST 3333–80
Graphite grease is intended for lubrication of hard heavy-loaded mechanisms (open gearboxes, screw joints, guide screws, jacks, springs, etc.).
Lubricant is efficient at the temperatures lower than minus 20°С in springs and other similar mechanisms.
Index name Graphite grease
Compliance with classifi cations NLGIDIN 51502
2OGF 2 G-20
Appearance Homogeneous thick black ointment with a silvery tinge
Thickener Ca
Operating temperature range, min…max, °С -20 (-30)...+60
Dropping point, °С, not less than 77
Penetration at 25°С, mm·10−1 Not less than 250
Shear strength at 50°С, Pa, not less than 100*
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than 100*
Colloid stability, %, not more than 5
* The index is determined by the manufacturer prior to the introduction of filler.
General-purpose lubricantsfor standard temperatures
REFERENCE BOOK
83
Grea
se
Gen
eral
-pur
pose
lubr
ican
ts
General-purpose lubricantsfor standard temperatures
Red calcium grease - rough friction units of rolling and sliding of machines and mechanisms of vehicles, agricultural machines, hand tools, screw and chain drives, low-speed gear reducers, etc.
Green rubber grease - rough friction units of rolling and sliding of machines and mechanisms of vehicles, agricultural machines, hand tools, screw and chain drives, low-speed gear reducers, etc. Contain rubber.
Index name Green Rubber Grease Red Calcium Grease
Compliance with classifi cations NLGIDIN 51502
2K2C-25
3K3C-25
2K2C-25
3K3C-25
Appearance Homogenous ointment with a smooth texture
from light to dark green color.
Homogenous ointment with a smooth texture
from pink to cherry color.
Operating temperature range, min…max, °С -25 … +65 -25 … +65
Thickener Са + rubber Са
Dropping point, °С, not less than 93 95 93 95
Penetration at 25°С, mm·10−1 265-295 220–250 265-295 220–250
Shear strength at 50°С, Pa, not less than 150 200 150 200
Colloid stability, %, not more than 11 10 11 10
REFERENCE BOOK
84
Grea
se
Gen
eral
-pur
pose
lubr
ican
ts
General-purpose lubricants
ТУ У 24.6-36451680-148:2010
Series of Molyroll EP multipurpose greases is intended for lubrication of different friction units of industrial equipment and vehicle mechanisms (all types of antifriction bearings, including sliding, rolling bearings and swivel joints (constant-velocity joints) etc.), that operates under conditions of high loads, vibrations and extreme pressures.
Molyroll EP 1 grease with a low-temperature flow is designed for centralized lubrication systems of friction units of casting, forging, pressing и other industrial equipment and machinery.
Molyroll EP 2 and EP 3 are embedded greases for different machinery and equipment.
Наименование показателя Molyroll EP1
Molyroll EP2
Molyroll EP3
Соответствие классификациям NLGIDIN 51502
1KF1K-40
2КF2K-40
3КF3K-40
Appearance Homogeneous smooth ointment colored from light gray to black
Thickener Li-K
Operating temperature, °С –40…+120
Worked penetration at 25°С (60 double strokes), m * 10-4, within 310-340 265–295 220–250
Shear strength at 50°С, Pa, not less than 150 200 300
Colloid stability, % of separated oil, not more than 20,0 15,0 12,0
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than 1500 1500 (25°С) 1600 (25°С)
Evaporation at 150°С for 1 hour, %, not more than 5,0
Tribological characteristics on 4 balls machine at (20±5) °С, H, not less than
• welding load, 3685 3685 3685
Dropping point, °С, not less than 185 190 190
Mass fraction of free alkalis in NaOH equivalent, %, mg КOH / g, not more than 0,2
REFERENCE BOOK
85
Grea
se
Aut
omot
ive
lubr
ican
ts
Automotive lubricants
TS U 23.2-30802090-040:2005
Grease Agrinol ShRUS - 4 is used for lubricating the constant velocity (CV-) joints of front wheel drive cars, cars with four-wheel drives, and double-row ball bearings, which are used in the nodes of the hubs of cars VAZ, ZAZ and AZLK.
TS U 23.2-30802090-079:2007
Agrinol Fiol-2U is used for greasing of needle bearings and spline joints of trunnion of driveshaft for VAZ cars and other vehicles.
Index name Grease Agrinol Fiol -2U Grease Agrinol ShRUS -4
Compliance with classifi cations NLGIDIN 51502 2 (KPF2N-40) 2 (KPF2K-40)
Appearance Silver-black homogenous ointment
Homogenous ointment colored from dark-grey to black
Thickener Li
Operating temperature range, min…max, °С -40..+120 (+130) -40..+120
Dropping point, °С, not less than 185 190
Penetration at 25°С, mm·10−1 255-295 250-280
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than
1800 (-30ºC)
Shear strength, Pa, within:• At 20°С • At 80°С
300-800-
300-700Not less than150
Colloid stability, %, not more than 12 16
Tribological characteristics on 4 balls machine at (20±5) °С, Н, not less than:• Welding load• Critical load• Scuff index
2450980470
49001098559
Automotive lubricantsREFERENCE BOOK
86
Grea
se
Aut
omot
ive
lubr
ican
ts
TS U 23.2-30802090-062:2006
Agrinol №158 greases are used for lubrication of roller bearings of automotive and tracktor equipment, needle bearings of cardan joints of unequal angular velocities. Agrinol №158M is distinguished by improved anti-wear characteristics and is recommended for usage in friction units with increased loads and low sliding speeds, such as constant velocity joints, and front-wheel-drive vehicles as well as in two-row ball bearings, which are used in hub nodes of cars.
TS U 23.2-30802090-043:2005
Agrinol ShRB-4 grease is used as an immutable in ball joints of front suspension, tips of rods of cars steering. Grease is characterized by high water resistance.
Index name Agrinol No158
Agrinol No158M Agrinol ShRB-4
Compliance with classifi cations NLGIDIN 51502
1/2KF 1/2 K-30
1/2KF 1/2 K-30
2K2K-40
Appearance Smooth homogenous ointment from blue to dark-
blue color
Slightly fi brous homogeneous dark
brown ointment without secondary inclusions
Thickener Li-K K-Ba
Operating temperature range, min…max, °С -30..+110 -40..+130
Dropping point, °С, not less than 150 140 200
Penetration at 25°С, mm·10−1 265-320 240-320 265-295
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than
400 (0ºC) 800 (-20ºC)
Shear strength, Pa, within: • 20ºC• 50 ºC
-160
-130
200-
Colloid stability, %, not more than 18 21 10
Tribological characteristics on 4 balls machine at (20±5) °С, Н, not less than:• Welding load• Critical load• Scuff index
-617
-
1842784343
1960588590
REFERENCE BOOK
87
Grea
se
Mul
ti-pu
rpos
e lu
bric
ants
Multi-purpose lubricants
TS U 23.2-36451680-127:2011
Ligrease grease series is designed for lubrication of various friction units of industrial equipment and machinery vehicles that operate at medium loads.
Ligrease 00 is used for the lubrication of enclosed gears and chain drives, bearings of gearboxes with insufficient sealing.
Ligrease 0 is designed for use in centralized lubrication systems continuously.Ligrease 1 is designed to lubricate the chassis and transmissions of passenger
cars, light and medium trucks, as well as friction units of industrial equipment, which is operating under heavy loads, vibration and extreme pressure.
Ligrease 2 and Ligrease 3 are used as mortgage greases.
Index name Ligrease 00 Ligrease 0 Ligrease 1
Compliance with classifi cations NLGI,DIN 51502
00K00G-30
0K0G-30
1K1K-40
Appearance Smooth homogenous ointment from light yellow to brown color.
Thickener LiOperating temperature range, min…max, °С –30…+100 –30…+110 –40…+120
Dropping point, °С, not less than 150 165 185
Penetration at 25°С, mm·10−1 380 – 430 340 – 380 310 – 340
Shear strength at 50°С, Pa not specifi ed 100 (20°С) 150
Colloid stability, %, not more than 35** 30 20
Mass fraction of free alkalis in NaOH equivalent, %, mg КOH / g, not more than 0,2
Mass fraction of mechanical impurities, %, not more than None
Water content, %, not more than Traces** The index is determined under a 200g load.
Multi-purpose lubricantsREFERENCE BOOK
88
Grea
se
Mul
ti-pu
rpos
e lu
bric
ants
TS U 23.2-36451680-127:2011
Ligrease grease series is designed for lubrication of various friction units of industrial equipment and machinery vehicles that operate at medium loads.
Ligrease 2 and Ligrease 3 are used as mortgage greases.
Index name Ligrease 2 Ligrease 3
Compliance with classifi cations NLGI,DIN 51502
2K2K-30
3K3K-30
Thickener Li
Operating temperature range, min…max, °С –30… +120 (+130)
–30 (-40)+120 (+130)
Dropping point, °С, not less than 190 190
Penetration at 25°С, mm·10−1 265 – 295 220 – 250
Shear strength at 50°С, Pa 200 300
Colloid stability, %, not more than 15 12Mass fraction of free alkalis in NaOH equivalent, %, mg КOH / g, not more than 0,2
Mass fraction of mechanical impurities, %, not more than None
Water content, %, not more than Traces
** The index is determined under a 200g load.
Multi-purpose lubricantsREFERENCE BOOK
89
Grea
se
Mul
ti-pu
rpos
e lu
bric
ants
TS U 23.2-36451680-127:2011
Ligrease ЕР grease series is designed for lubrication of friction units of various industrial equipment and machinery vehicles that operate at high loads, where elevated EP properties are needed.
Ligrease ЕР 00 is designed for the lubrication of earboxes and gear drives, rolling and sliding bearings, in centralized lubrication systems.
Ligrease ЕР 0 is recommended for the lubrication of heavily loaded gearboxes and gear drives, in centralized lubrication systems of vehicles and industrial equipment.
Ligrease ЕР 1 is a lubricant with a low-temperature fluidity designed for centralized lubrication systems of friction units for casting, forging and other industrial equipment operating under heavy loads, vibration and extreme pressure.
Index name Ligrease ЕР 00
Ligrease ЕР 0
Ligrease ЕР 1
Compliance with classifi cations NLGI,DIN 51502
00KР00К-30
0KР0К-30
1KР1K-40
Appearance Smooth homogenous ointment from light yellow to brown color.
Thickener Li+ЕР
Operating temperature range, min…max, °С –30…+120 –30…+120 –40…+120
Dropping point, °С, not less than 150 165 185
Penetration at 25°С, mm·10−1 380 – 430 340 – 380 310 – 340
Shear strength at 50°С, Pa not specifi ed 100 (20°С) 150
Colloid stability, %, not more than 35** 30 20
Mass fraction of free alkalis in NaOH equivalent, %, mg КOH / g, not more than 0,2
Mass fraction of mechanical impurities, %, not more than None
Water content, %, not more than TracesTribological characteristics on 4 balls machineat (20±5) °С, Н, not less than:
• welding load 2607 2607 2607
** The index is determined under a 200g load.
Multi-purpose lubricantsREFERENCE BOOK
90
Grea
se
Mul
ti-pu
rpos
e lu
bric
ants
TS U 23.2-36451680-127:2011
Ligrease ЕР grease series is designed for lubrication of friction units of various industrial equipment and machinery vehicles that operate at high loads, where elevated EP properties are needed.
Ligrease ЕР 2 and Ligrease ЕР 3 are used as mortgage.
Index name Ligrease ЕР 2 Ligrease ЕР 3
Compliance with classifi cations NLGI,DIN 51502
2KР2K-30
3KP3K-30
Appearance Smooth homogenous ointment from light yellow to brown color.
Thickener Li+EP
Operating temperature range, min…max, °С –30…+130 –30…+130
Dropping point, °С, not less than 190 190Penetration at 25°С, mm·10−1 265 – 295 220 – 250
Shear strength at 50°С, Pa 200 300
Colloid stability, %, not more than 15 12Mass fraction of free alkalis in NaOH equivalent, %, mg КOH / g, not more than 0,2
Mass fraction of mechanical impurities, %, not more than None
Water content, %, not more than Traces
Tribological characteristics on 4 balls machine at (20±5) °С,N, not less than
• welding load 2764 2764
** The index is determined under a 200g load
Multi-purpose lubricantsREFERENCE BOOK
91
Grea
se
Mul
ti-pu
rpos
e lu
bric
ants
TS U 23.2-30802090-014:2002
Agrinol 1-13 is universal anti-frictional non-waterproof sodium-calcium grease.
Grease is used for lubricating of rolling and sliding friction units of machines and mechanisms working at the temperature from minus 20°С to 110°С. Grease remains efficient in rather powerful mechanisms at the temperature down to minus 40°С.
Grease can be supplied to friction units by the superchargers or by the mortgage way.
GOST 1957–73
Universal refractory non-waterproof greases Konstalin-1 and Konstalin-2 are used for lubrication of fan friction units of casting machines, blast furnaces and cement kilns, roller bearing on the rail transport.
Index name Agrinol 1-13 Konstalin-1 grease
Konstalin-2 grease
Compliance with classifi cations NLGIDIN 51502
3/4K 3/4 H-20
2/3K 2/3 H-20
3/4K 3/4 H-20
Appearance Homogeneous ointment from
light yellow to dark brown color
Thickener Na-Ca Na
Operating temperature range, min…max, °С -20...+110
Dropping point, °С, not less than 125 130 150
Penetration at 25°С, mm·10−1 180-260 225-275 175-225
Shear strength at 80°С, Pa, not less than 100-400 -
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than
500 -
Colloid stability, %, not more than 18 -
Corrosive effect on metals Pass
for standard and high temperatures
REFERENCE BOOK
92
Grea
se
Indu
stria
l lub
rica
nts
Industrial lubricantsWater-resistant
TS U 23.2-30802090-132:2009
SKS 300 m are multi-purpose, heat-resistant, waterproof sulfonate-calcium greases that are recommended for lubricating of industrial equipment bearings, working under the high loads, high temperatures and water contact.
Lubricants of SKS 300 m-1 and SKS 300 m-1* brands can be used in centralized lubricating systems and devices with forced feeding of lubricants in friction units. Lubricants branded as SKS 300 m-2 and SKS 300 m-2* are recommended for lubrication of embedded bearings.
The types of greases, marked with asterisks differ only in color (red).
Index name SKS-300 m-1
SKS 300 m-1*
SKS-300 m-2
SKS 300 m-2*
Compliance with classifi cations NLGIDIN 51502
1/2KP1/2R-25
2KP2R-20
Appearance Homogenous smooth brown ointment
Homogenous smooth red ointment
Thickener Са Sulfonate complex
Operating temperature range, min…max, °С -25..+180 -20..+190
Dropping point, °С, not less than 300
Penetration at 25°С, mm·10−1 280-320 250-280
Shear strength at 50°С, Pa, not less than 120 200
Colloid stability, %, not more than 4 3
Evaporation at 120°С, %, not more than 2 1,5
Water resistance, class, not less than 2 1,5
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 800 (-10ºC) 1100 (-10ºC)
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:• Welding load• Critical load• Deterioration rate (196 Н), mm, not more
than
413612300,5
Industrial lubricantsREFERENCE BOOK
93
Grea
se
Indu
stria
l lub
rica
nts
GOST 20.5-32365441-207:2016TS U 23.2-30802090-126:2009
PELLETON EP, PELLETON LX - water-resistant high-temperature greases. Specially designed for use in a wide range of temperatures and high load in bearing pellet presses in joints and mechanisms of industrial, metallurgical, mining and extraction equipment, ceramic production, tunnel furnaces, hot conveyors; auto tractor, agricultural and road machinery.
Index name PELLETON EP
PELLETON EP
PELLETON LX
PELLETON LX
Match classifi cationNLGI
ISO 6743-9DIN 51502
1L-XBDHB 1KP1N-25
2L-XBDHB 2 KP2N-20
1L-XBDHB 1
KP1R-25
2L-XBDHB 2
KP2R-30
Thickener k-Ca k-Li
Application temperature, °С -20 … 150(170) -25(-30) ... +170 (180)
Appearance Homogeneous smooth ointment from light yellow to brown color
Penetration at 25 °C with stirring (60 double strokes) m 10-4,within 310-340 265-295 290-340 265-295
Dropping Point, °C, not lower than 230 250Volatility,%, not more 3
Shear strength, Pa, not less than: • at 50°С • at 80°С
100-60080-600
200200
100-
150
-
Effective viscosity at 0 °C and average gradient of the strain rate pass of 10 s-1 Pass, no more than
110 160 1600(-20 °С) 2000(-20 °С)
lubricating properties at the 4-ball machine at (20 ± 5) ° C, N, not less than:
• Welding load; • critical load; • scuff index
61741098684
3087980440
Water resistance grade, not less than 1B
Corrosive effect on metals Pass
Industrial lubricantsREFERENCE BOOK
94
Grea
se
Indu
stria
l lub
rica
nts
GOST 20.5-32365441-207:2016TS U 23.2-30802090-126:2009
PELLETON SKS - water-resistant high-temperature grease. Specially designed for use in a wide range of temperatures and high load in bearing pellet presses in joints and mechanisms of industrial, metallurgical, mining and extraction equipment, ceramic production, tunnel furnaces, hot conveyors; auto tractor, agricultural and road machinery.
Index name PELLETON SKS PELLETON SKS
Match classifi cation NLGIISO 6743-9 DIN 51502
1KP1S-25
2KP2S-20
Thickener Ca Sulfanate complex
Application temperature, °С -25 … +200
Appearance Homogeneous smooth ointment from light yellow to brown color
Penetration at 25 °C with stirring (60 double strokes) m 10-4, within 280-320 250-280
Dropping Point, ° C, not lower than 300Volatility,%, not more 2 1,5
Shear strength, Pa, not less than: • - at 50°С 120 200
Effective viscosity at -10°C and average gradient of the strain rate of 10 s-1 , no more than
800 1100
lubricating properties at the 4-ball machine at (20 ± 5) ° C, N, not less than:• Welding load;
4136 -
Water resistance grade, not less than 1B
Corrosive effect on metals Pass
Industrial lubricantsREFERENCE BOOK
95
Grea
se
Indu
stria
l lub
rica
nts
ТS U 20.5-32365441-192:2014
Agrinol Polynol EP recommended for extreme pressure lubrication of industrial bearings in chemical, paper industry, casting and rolling mills, high loaded slider bearings, frictionless bearings and ball-bearings, when long life lubricating is needed: hot-rolling steel mills; hot rollers in manufacturing of carton (drying ovens); huge electric motors. Biodegradation of grease is from 30% to 75%.
Agrinol Polynol HDS 460 recommended for lubrication of low- and middle-speed industrial bearings, working at high temperature and high loads in chemical, paper industry, casting and rolling mills, recommended for lubricating by centralized grease system: live rollers in Continuous Casting Machines; conveyer rollers in continuous furnaces; for other high temperature applications, such as:annealing furnace, drying ovens; friction bearing in pouring cranes; hot rollers in manufacturing of carton; asphalt pavers.
Index name Agrinol Polynol ЕР1
Agrinol Polynol ЕР2
Agrinol PolynolHDS 460
Compliance with classifi cations NLGIDIN 51502ISO 6743
1KP1Р-10
L-XAEEB-1
2KP2Р-10
L-XAEEB-2
1/2KHCP 1/2 R-30
L-XCFEB-1
Thickener Polyurea
Penetration at 25°С with stirring (60 double cycles), m*10-4, within 260-290 260-300 280-330
Dropping point, °С, not lower than 260 260 260
Colloid stability, % of selected oil, no more than 5 6 6
Shear strength at 50°С, Pa, not less than 140-600 1,0-4,0 150
Evaporation, %, not more than 3 3 2
Water resistance, grade, not less than 1c 1c 1c
Stability against oxidation, mg KOH/g, not more than 1 1 0,5
Lubricating properties at the 4-ball friction machine:• Welding load, N, not less than• Critical load, not less than• Scuff index, not more than• Wear out rate at 196N, mm, no more than
328310984400,4
328310984400,4
32831235
-0,38
Industrial lubricantsREFERENCE BOOK
96
Grea
se
Indu
stria
l lub
rica
nts
Bentol-1 M intended for the lubrication of plain and rolling bearings operating at low speed and high temperature or under cyclical temperature changes from room temperature to high.
Particularly suited for the lubrication of plain bearings of mechanisms, operating at long relubrication intervals, low speeds or exposed shock loading.
Operating temperature range: from minus 10оС up to 170о С (in short-term up to 180о С).
Index name BENTOL-1 M
Compliance with classifi cations NLGIDIN 51502ISO 6743
1KF1Р-0
L-XAFHB-1
Appearance Homogeneous ointment gray-black color, green tint
allowed
Kinematic viscosity of base oil at 40°С, mm2 / s 400-460
Penetration at 25°С with stirring (60 double cycles), m*10-4, within 310-340
Dropping point, °С, not lower than 250
Colloid stability, % of selected oil, no more than 10
Evaporation at 120 ° C, 1h.,%, not more than 2
Tensile shear strength at 50 °C, Pa, not less than 1,0
Lubricating properties at the 4-ball friction machine:• welding load, (Rs), N(kGs), not less• Deterioration rate at 196 N, mm, no more than
19600,5
Industrial lubricantsREFERENCE BOOK
97
Grea
se
Indu
stria
l lub
rica
nts
TS U 23.2-30802090-084:2008
Lubricants for rolling mills Sliding GR are designed for the lubrication of roller bearings of rolling mills, heavy duty rollers and ball bearings of nodes of industrial equipment.
Semi-fluid greases Sliding GR 00 and Sliding GR 0 are intended for use in centralized continuous lubrication systems.
Index name Sliding GR 00 Sliding GR 0
Compliance with classifi cations NLGIDIN 51502
00KP0OР-20
0KP0Р-20
Appearance Homogenous smooth brown ointment
Thickener Li complex
Operating temperature range, min…max, °С –20 … +170 –20 … +170
Dropping point, °С, not less than 230 250
Penetration at 25°С, mm·10 – 1 370 – 430 330 – 380
Shear strength at 50°С, Pa, not less than – >50
Colloid stability, %, not more than 12 12
Evaporation at 120°С within 1 hour, %, not more than 3
Water resistance, class, not less than: – 1b
Effective viscosity at minus 20°С and with average gradient of the strain rate 10 s-1, Pa·s, not more than 1500 1600
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than:
• Welding load • Critical load • Scuff index • Deterioration rate (196 N), mm, not more than
32839804400,45
Industrial lubricantsREFERENCE BOOK
98
Grea
se
Indu
stria
l lub
rica
nts
TS U 23.2-30802090-084:2008
Lubricants for rolling mills Sliding GR are designed for the lubrication of roller bearings of rolling mills, heavy duty rollers and ball bearings of nodes of industrial equipment.
Sliding GR1 — for centralized systems of continuous lubrication. Sliding GR2 is used as mortgage grease.
Index name Sliding GR 1 Sliding GR 2
Compliance with classifi cations NLGIDIN 51502
1KP1R-20
2KP2R-30
Appearance Homogenous smooth brown ointment
Thickener Li complex
Operating temperature range, min…max, °С - 20 (-30) … +150 (+180)
Dropping point, °С, not less than 250 260
Penetration at 25°С, mm·10−1 290–340 260–290
Shear strength at 50°С, Pa, not less than 100–420 140–640
Colloid stability, %, not more than 7 6
Evaporation at 120°С within 1 hour, %, not more than 3
Water resistance, class, not less than 1b
Effective viscosity at minus 20°С and with average gradient of the strain rate 10 s-1, Pa·s, not more than
1600 2000
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:• Welding load• Critical load• Scuff index• Deterioration rate (196 Н), mm, not more than
32839804400,40
Industrial lubricantsREFERENCE BOOK
99
Grea
se
Indu
stria
l lub
rica
nts
Sliding EP2 SHC 220 - grease of wide application for operation under high pressure, which is recommended for use in heavy vehicles and industrial equipment.
Recommended operating temperature range for the Sliding EP2 SHC 220 from -45 ° C up to 170 ° C.
Index name Sliding EP 2 SHC 220
Compliance with classifi cations NLGIDIN 51502
2GPHC 2K-30
Appearance Smooth, elastic ointment of red color
Thickener Li complex
Operating temperature range, min…max, °С - 45 … 190 (220)
Appearance Smooth, elastic ointment of red color
Dropping point, °С, not less than 270
Penetration at 25°С, mm·10−1 265–295
Water resistance, class, not less than 1A
Tensile strength at 50 ° C, Pa 580
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than• Welding load• Critical load• Scuff index• Deterioration rate (196 Н), mm, not more than
24509804400,5
Industrial lubricantsREFERENCE BOOK
100
Grea
se
Indu
stria
l lub
rica
nts
TS U 23.2-30802090-032:2006
Agrinol Termostan is a heat-resistant lubricant for heavy-loaded friction units, that is used as a greasing material for frictionless bearings of average and low speed and other friction units exploited at elevated temperature and loading rolling mill rolls, founding equipment, calcinators and thermal furnaces etc. It also can be used in a short-term period at the temperature not higher than 280 °С if the unit is hermetic.
The lubricant should be feeded into friction units manually by the mortgage method or by greasing of attrition faces.
Index name Agrniol Termostan
Compliance with classifi cations NLGIDIN 51502
2KF2U-20
Appearance Homogeneous smooth ointment of black color
Thickener Li complex
Operating temperature range, min…max, °С -20..+230 (+280)
Dropping point, °С, not less than 260
Penetration at 25°С, mm·10−1 250-300
Shear strength at 50°С, Pa, not less than 300
Colloid stability, %, not more than 5
Water resistance, class, not less than 1b
Penetration change, mm·10-1 -
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 1500 (0ºC)
Tribological characteristics on 4 balls machine at (20±5) °С,N, not less than• Welding load• Critical load• Scuff index• Deterioration rate (196 Н), mm, not more than
61749807500,7
Industrial lubricantsREFERENCE BOOK
101
Grea
se
Indu
stria
l lub
rica
nts
TS U 30802090.002:2000
Agrinol IP-1l (summer) and Agrinol IP-1z (winter) are antifriction water-resistant greases for centralized lubrication systems of rolling mills, blast furnaces and other large-sized equipment of metallurgical enterprises.
These greases are intended for lubricating of friction units of industrial equipment functioning at the average and heavy losses.
Index name Agrinol İP-1l Agrinol İP-1z
Compliance with classifi cations NLGIDIN 51502
1/2K 1/2 C-0
0/1K 0/1 D-10
Appearance Homogeneous ointment from light-yellow to dark-brown color
Thickener Ca
Operating temperature range, min…max, °С +10...+80 -10..+80
Dropping point, °С, not less than 95 92
Penetration at 25°С, mm·10−1 270-310 310-360
Shear strength, Pa, not less than: • At 20°С • At 50°С
-Not less than 130
Not less than 130-
Colloid stability, %, not more than 10 12
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 250 (00C) 200 (00C)
Industrial lubricantsREFERENCE BOOK
102
Grea
se
Indu
stria
l lub
rica
nts
TS U 23.2-30802090-087:2008
Agrinol Uniol-2M grease are used for greasing of rolling mills, blast furnaces and other large equipment of metallurgical enterprises. Agrinol Uniol-2M-1 grease is used for greasing of embedded parts, and lubricant grease Agrinol Uniol-2M-2 — for centralized lubrication systems.
TS U 23.2-30802090-045:2005
Grease Agrinol ProkatOl is intended for lubrication of mechanisms operating at high specific loads: friction units of industrial, metallurgical equipment, tunnel furnaces, hot conveyors, mining equipment, of automotive, agricultural machinery, municipal electric, ceramic production.
Index name Agrinol Uniol-2M-1
Agrinol Uniol-2M-2
Agrinol ProkatOl
ЕР 2
Compliance with classifi cations NLGIDIN 51502
2KP2P-20
0/1KP0/1P-30
1/2KP1/2Р-10
Appearance Homogeneous grease from light-yellow to dark-brown
color
Thickener Li complex Li complex
Operating temperature range, min…max, °С -10..+150 (+170)
-20..+150 (+170)
-10 … 150 (+170)
Dropping point, °С, not less than 230 245
Penetration at 25°С, mm·10−1 265-320 320-380 265-320
Shear strength, Pa, not less than: • At 20°С • At 50°С
-Not less than
200
-100-600
Colloid stability, %, not more than 9 12 8
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 160 (00C) 110 (00C) 220
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than• Welding load• Critical load• Scuff index
2323980392
49001381650
Industrial lubricantsREFERENCE BOOK
103
Grea
se
Indu
stria
l lub
rica
nts
TS U 23.2-36451680-127:2010
Multi-purpose water-resistant antifrictional greases of LubriLiCa WR series are designed for lubrication of various medium-loaded friction units of industrial equipment (rolling and sliding bearings, gears of industrial machinery and other similar systems), mechanisms of transport vehicles and agricultural machines, which operate under conditions of high humidity in the temperature range from minus 30 °С up to 120 °С.
Index nameLubriLiCa
WR 1 WR 2 WR 3
Compliance with classifi cations NLGIDIN 51502
1K1K-30
2K2K-30
3K3K-30
Appearance Homogeneous smooth ointment from light- to dark brown color
Thickener Li-Ca
Operating temperature range, min…max, °С -30..+110 -30..+110 -30..+120
Dropping point, °С, not less than 160 170 175
Penetration at 25°С, mm·10−1305-345 260-300 215-255
• Mechanical impurities not dissolved in HCl• Water• Free alkalis in NaOH equivalent, mgКОН / g
0,025Traces0,15
Colloid stability, %, not more than 18 15 10
Corrosion tests at 100°С, 3 hours• Copper М0k, М1k, М0b or М1• Steel mk. 45
PassPass
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than• Welding load Not specifi ed
Industrial GreasesREFERENCE BOOK
104
Grea
se
Indu
stria
l Gre
ases
TS U 23.2-36451680-127:2010
Multi-purpose water-resistant antifrictional greases of LubriLiCa ЕР series are designed for lubrication of various friction units of industrial equipment (rolling and sliding bearings, gears of industrial machinery and other similar systems), mechanisms of transport vehicles and agricultural machines, which operate under conditions of high humidity in the temperature range from minus 30 °С up to 120 °С.
Index nameLubriLiCa
EP 1 EP 2 EP 3
Compliance with classifi cations NLGIDIN 51502
1KP1K-30
2KP2K-30
3KP3K-30
Appearance Homogeneous smooth ointment from light- to dark brown color
Thickener Li-Ca
Operating temperature range, min…max, °С -30..+110 -30..+110 -30..+120
Dropping point, °С, not less than 160 170 175
Penetration at 25°С, mm·10−1 305-345 260-300 215-255
• Mechanical impurities not dissolved in HCl• Water• Free alkalis in NaOH equivalent, mgКОН / g
0,025Traces0,15
Colloid stability, %, not more than 18 15 10
Corrosion tests at 100°С, 3 hours• Copper М0k, М1k, М0b or М1• Steel mk. 45
PassPass
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than• Welding load 2607
Industrial GreasesREFERENCE BOOK
105
Grea
se
Indu
stria
l Gre
ases
Metal-plating lubricants
TS U 23.2-30802090-081:2007
Plating GR is a metal plating plastic greace with attrition restorative effect. It is used for lubrication of heavy-loaded units and machines of metallurgical, mining and machine-building equipment.
Index name Plating GR
Compliance with classifi cations NLGIDIN 51502
2 / 3K 2 / 3 N-30
Appearance
Homogeneous ointment, with a smooth structure from light
green to dark green-brown color.
Thickener Li complex
Operating temperature range, min…max, °С –30 … +150
Dropping point, °С, not less than 250
Penetration at 25°С, mm·10−1 220 – 280
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 800 (0°С)
Shear strength at 80°С, Pa, not less than 2,0
Colloid stability, %, not more than 10
Evaporation at 100°С, %, not more than 4
Water resistance, class 1а; 1b
Tribological characteristics on 4 balls machine at (20±5) °С,N, not less than:
• Critical load • Scuff index
784320
Industrial GreasesREFERENCE BOOK
106
Grea
se
Indu
stria
l Gre
ases
Industrial lubricants for rolling mills
TS U 23.2-30802090-086:2008
Rolling GR are industrial greases for rolling mills designed for centralized lubrication systems, blast furnaces, rolling and sliding bearings, hinges, screw and chain drives, low-speed reducers, friction units of transport machinery, hand tools and agricultural equipment.
Rolling GR S — summer grease, Rolling GR W — winter grease.Rolling GR SW — for multigrade application.
Index name Rolling GR S Rolling GR W Rolling GR SW
Compliance with classifi cations NLGIDIN 51502
2K2E-0
0/1K0/1E-10
2/3K2/3E-20
Appearance Homogeneous smooth ointment from light- to dark brown color
Thickener Ca
Operating temperature range, min…max, °С +10..+80 -10..+80 -20..+80
Dropping point, °С, not less than 95 92 93
Penetration at 25°С, mm·10−1 270-310 310-360 230-300
Shear strength at 50°С, Pa, not less than 130 100 150
Colloid stability, % of secreted oil, not more than 10 12 11
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 250 200 330
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:• Welding load• Critical load• Scuff index• Deterioration rate (196 Н), mm, not more
than
19609804000,6
REFERENCE BOOK
107
Grea
se
Rai
lway
Gre
ases
Railway Greases
GOST 19791-74
LZ-CNII grease is intended for roller bearings of railroad wagons axle-boxes.
TS U 24.6-30802090-024-2004
Agrinol MZT is a antifrictional water-resistant plastic grease, intended for lubrication of wheelset roller bearings of wheelpairs of railway rolling stocks. Grease can be used for lubrication of roller bearings of industrial and electric machines, conveyors and diverse mechanisms of industrial (e.g. rolling mills, machines), agricultural, constructing equipment etc. by the mortgage method.
Index name LZ-CNİİ Agrinol MZT
Compliance with classifi cations NLGIDIN 51502
3/4KP 3/4 G-60
2/3KP 2/3 K-30
Appearance Homogeneous smooth ointment from light yellow
to dark yellow.
Homogeneous ointment from light yellow to
dark brown color
Thickener Ca-Na Li complex
Operating temperature range, min…max, °С -60...+100 -30...+130 (+150)
Dropping point, °С, not less than 135 230
Penetration at 25°С, mm·10−1 200-260 240-290
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than 420 (0ºC) 2000 (-30ºC)
Shear strength, Pa, within:• 20ºC• 50ºC
-220
440196
Colloid stability, %, not more than 22 12
Tribological characteristics on 4 balls machine at (20±5) °С, Н, not less than:• Welding load• Critical load• Scuff index
---
3087980480
Railway GreasesREFERENCE BOOK
108
Grea
se
Rai
lway
Gre
ases
TS U 23.2-30802090-006-2003
Agrinol ZhRO grease is intended for usage in friction bearings of locomotives, diesel trains, rolling stocks of rail wagons.
TS U 23.2-36451680-162:2011
Agrinol Buksol grease is designed for use in friction bearings of locomotives, passenger and freight wagons, motor wagon rolling stocks, including those that operate in a speed up to 200km/h. Service life of grease for wagons amounts to 5 years or 450 000 kilometers by run.
Operating temperature range for Agrinol Buksol grease ranges from minus 60°С to 60°С, also grease is allowed for use at the temperatures up to 120°C (in friction units).
Index name Agrinol ZhRO Agrinol Buksol
Compliance with classifi cations NLGIDIN 51502 3/4 KP 3/4 H-50 2/3 KP 2/3 C-60
Appearance Homogenous smooth ointment from light-yellow to brown color.
Homogenous smooth ointment from light-yellow
to dark-brown color.
Thickener Li Li
Operating temperature range, min…max, °С -50...+120 (+130) -60...+60 (+120)
Dropping point, °С, not less than 175 180
Penetration at 25°С, mm·10−1 190-250 230-290
Effective viscosity at 0°С and with average gradient of the strain rate 10 s−1, Pa·s, not more than 2000 1300
Evaporation at 100°С for 1 hour, %, not more than 2,5 2,5
Colloid stability, %, not more than 15 18
Tribological characteristics on 4 balls machine at (20±5) °С:• Critical load, N, not less than• Diameter of the wear spot (196Н), mm, Н, not
more than
--
7840,5
Railway GreasesREFERENCE BOOK
109
Grea
se
Rai
lway
Gre
ases
TS U 24.6-30802090-058:2006
Agrinol ZhT-72 is used for lubrication of breaking devices of railway rolling stocks (locomotive brakess during friction of rubber on metal) and similar equipment in other industries, transport, argiculture.
TS U 24.6-30802090-059:2007
Agrinol ZhT-79L grease is used in brake systems of railway rolling stocks for lubrication of rubber and rubber-tissue sealing parts of break systems and for lubrication of friction surfaces: “metal - metal” and “metal - rubber”.
This product also can be used in electrical equipment friction surfaces of rolling stock: in bearing devices, hinges and all relays, wipers, pressure regulators, in the cylinders and sealing cuffs of rubber pistons of pneumatic drives of locomotives and wagons, except the cases of using leather wrist pistons.
TS U 23.2-30802090-100:2009
Agrinol ZhTKZ-65 grease is designed for lubrication of breaking equipment and mechanisms of locomotive, diesel-trains, motor-wagon rolling stocks, working with small shear. The main consumers of grease are: railway, subway organizations, enterprises and tram services.
Index name Agrinol ZhT-72
Agrinol ZhT-79L
Agrinol ZhTКZ-65
Compliance with classifi cations NLGIDIN 51502
-KSIK-60
2KSI 2 K-60
2/3OG 2/3 G-60
Thickener Ca complex Li Li
Operating temperature range, min…max, °С -60..+120 (+150)
-60..+120 (+150) -60..+110
Dropping point, °С, not less than - - 120
Penetration at 25°С, mm·10−1 - 240-290 230-300
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 800 (-55ºC) 800 (-55ºC) 1500 (-50ºC)
Shear strength, Pa, within:, 50ºC 50 250 -
Colloid stability, %, not more than 10 15 40
Railway GreasesREFERENCE BOOK
110
Grea
se
Rai
lway
Gre
ases
TS U 23.2-30802090-055:2006
Greases Agrinol Relsol M and Agrinol Relsol GS are used for greasing of “wheel-rail” friction parts of railway transport. Greases are fed into the zone of wheel pair flanges by the lubricating device with periodic lubrication (grease Agrinol Relsol М must be fed under the pressure).
TS U 23.2-30802090-075:2007
The metal plating semi-fluid grease Agrinol Puma-M is used for lubricating of heavy-loaded toothed gears in reducers of locomotive engines as well as for increasing durability at the contact of wheel pair combs with rails. The lubricant is placed on wheel combs or cheeks of rails with the help of movable greasing mechanisms. If the lubricant is placed into friction units, mortgage method is applied. Agrinol Puma Ml — is summer grease, Agrinol Puma Mz is winter grease.
Index name Agrinol Relsol M
Agrinol Relsol GS
Agrinol Puma-Мl
Agrinol Puma-Мz
Compliance with classifi cations NLGIDIN 51502
00GP00C-30
000GP000C-30
1/2G ½ G-40
0/00G 0/00 E-40
Thickener Ca Li
Operating temperature range, min…max, °С -30..+50 -40..+50 -40..+110 -45..+80
Dropping point, °С, not less than 70 - 140 Not specifi ed
Penetration at 25°С with stirring (60 double strokes), 440-445 445-495 280-350 350-440
Colloid stability, % of secreted oil, not more than - 35 Not
specifi ed
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than
• Welding load • Critical load • Deterioration rate (196 Н), mm, not
more than
1260560
-
--
0,7
REFERENCE BOOK
111
Grea
se
Hea
t-re
sist
ant g
reas
es
Heat-resistant greases
TS U 24.6-32365441-170:2011
Agrinol Termol greases are used in roller bearings and other parts and mechanisms, which are amenable to high temperatures (for example: circulation fans of BN gas furnaces, conveyor mechanisms and tunnel kilns).
Agrinol Termol-1 is a synthetic grease with special additives, used in sed in the operating temperature range from –40 °C to +400 °C.
Agrinol Termol-2 is a mineral based grease used in the temperature range from –40 °C to +300 °C.
Agrinol Termol greases are clean, non-toxic lubricants.
Index name Agrinol Termol-1 Agrinol Termol-2
Compliance with classifi cations NLGIDIN 51502
1/2K HC PF 1/2 U-40
1/2KP1/2U-40
Appearance homogeneous smooth black
ointment
Homogeneous ointment from
yellow to brown color
Thickener Inorganic
Operating temperature range, min…max, °С -40ºC..+400ºC -40ºC..+300ºC
Penetration at 25°С with stirring (60 double strokes), m 10 – 4, within 265-310 265-310
Colloid stability, % of separated secreted oil, not more than 12 12
Evaporation at 150ºС within 1 hour, %, not more than 2,0 2,0
Corrosive effect on metals (steel mk. 45 according to GOST 1050) Pass Pass
Mass fraction of water, %, not more than 0,2 0,2
Heat-resistant greasesREFERENCE BOOK
112
Grea
se
Hea
t-re
sist
ant g
reas
es
TS U 24.6-36451680-148:2010
Molyroll GR1 grease is designed for lubrication of roller bearings of industrial equipment, which operates at high loads (roller bearings of thrust chains, conveyors, transporters, cameras of bonderization, friction units of dispenser chains of iron castings).
Molyroll GR2 grease is used for lubrication of joints of universal spindles in centralized lubrication systems of rolling mills.
Index name MOLYROLL GR1 MOLYROLL GR1
Compliance with classifi cations NLGIDIN 51502
2KF2P-15
0KF0P-15
Appearance Homogeneous smooth ointment of black color
Thickener Inorganic
Operating temperature range, min…max, °С -15ºC..+160ºC
Penetration at 25°С, mm·10−1 265-295 340-400
Shear strength, Pa, within: 40 30
Colloid stability, %, not more than 8,0 10,0
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 150 (25ºC) 100 (25ºC)
Evaporation at 150°С within 1 hour, %, not more than 5,0
Thermal stability at 150°С within 1 hour Pass
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than• Welding load• Critical load• Scuff index
27641580790
Heat-resistant greasesREFERENCE BOOK
113
Grea
se
Hea
t-re
sist
ant g
reas
es
TS U 23.2-30802090-007:2004
Grease Aerol-А is used for the lubrication of roller bearings of industrial equipment, operating under the heavy loads (roller bearings of thrust chains, conveyors, transporters, bonderization cameras, friction units of dispenser chains of iron castings).
Grease Aerol-1А is intended for lubrication of joints of universal spindles in centralized lubrication systems of rolling mills.
Index name Aerol-A Aerol-1A
Compliance with classifi cations NLGIDIN 51502
2KF2P-15
0KF0P-15
Appearance Homogeneous ointment black color
Thickener Inorganic
Operating temperature range, min…max, °С -15ºC..+160ºC
Dropping point, °С, not less than 250 -
Penetration at 25°С, mm·10−1 265-295 340-400
Shear strength, Pa, within:, 50C 30 3
Colloid stability, %, not more than 8,0 10,0
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 150 (25ºC) 100 (25ºC)
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than• Welding load• Critical load• Scuff index
25101580790
Heat-resistant greasesREFERENCE BOOK
114
Grea
se
Hea
t-re
sist
ant g
reas
es
GOST 9433-80ММ
Plastic grease CIATIM-221 is designed for lubrication of roller bearings of electric machines, control systems and devices with rotation speed up to 10,000 min-1and the associated surfaces of “metal-metal” and “metal-rubber” types, working in a vacuum at the residual pressure of 666.5 Pa.
TS U 23.2-30802090-093:2008
Agrinol Grafitol grease is designed for lubrication of high-temperature friction and sliding units, such as: bearings, hot fans, hinges, kiln locks and other industrial machinery.
Contains graphite.
Index name CIATIM-221 Agrinol Grafi tol
Compliance with classifi cations NLGIDIN 51502
1/2Ksi 1/2 N-60
2KF2R-25
Appearance Homogeneous smooth ointment
from light yellow to light brown color
Homogeneous soft ointment of
black color without extraneous inclusions
Thickener Ca complex Inorganic
Operating temperature range, min…max, °С -60ºC..+150ºC -25ºC..+180ºC
Dropping point, °С, not less than 200 250
Penetration at 25°С, mm·10−1 380-360 265-29
Shear strength, Pa, within:, 120 (50ºC) 30 (20ºC)
Colloid stability, %, not more than 7 8
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 800 (-50ºC) 300 (0ºC)
Heat-resistant greasesREFERENCE BOOK
115
Grea
se
Hea
t-re
sist
ant g
reas
es
GOST 19774–74
VNII NP-207 grease is used in roller bearings of electric machines and starter-generators with rotation speed of 10,000 min−1.
Product is efficient at residual pressure of 666.5 Pa.
TS U 24.6-30802090-104:2008
Heat-resistant synthetic lubricant Agrinol VNII NP-210 is used for lubrication of heavily loaded slow moving bearings and bearings with oscillatory motion of the friction surfaces at small angles of swing.
Product is efficient at residual pressure of 666.5 Pa.
TS U 24.6-30802090-088:2008
Grease Agrinol VNII NP-219 is used in ballscrews, bearings of electric motors and starter-generators with high loads and speed up to 9000 min−1 .
Index name VNİİ NP -207 Agrinol VNİİ NP -210
Agrinol VNİİ NP -219
Compliance with classifi cations NLGIDIN 51502
3KSi 3S-60
1KSi F 1 U-20
0/1KSi F 0/1 R-50
Appearance Homogeneous smooth
ointment from light yellow
to dark-brown color
Homogeneous soft ointment of black color with a blue
tint
Homogeneous soft ointment from dark gray to black color.
Thickener Ca complex - Ca complex
Operating temperature range, min…max, °С -60ºC..+200ºC -20ºC..+350ºC -50ºC..+180ºC (+200)
Penetration at 25°С, mm·10−1 Not specifi ed Not specifi ed 300-380
Shear strength, Pa, within:, 80ºC 68,6 Not specifi ed 70,00
Colloid stability, %, not more than 6,0 12 7,0
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than 1400 (-30ºC) 750 (-10ºC) 1400 (-30ºC)
REFERENCE BOOK
116
Grea
se
Che
mic
ally
resi
stan
t lub
rica
nts
Chemically resistant lubricants
GOST 8551–74
CIATIM-205 is a plastic lubricant intended for capsulation and prevention of caking of immobile screw joints and seals contacting with aggressive media (concentrated non-organic acids, alkalis, amines, alcohol, hydrazines) and working within the temperature range from minus 60 °С to +50 °С. The minimal temperature of the lubricant’s usage for movable screw joints is minus 20 °С.
GOST 14296–78
VNII NP-279 grease is intended for greasing rolling and plain bearings, threaded joints, connectors, valves, etc., operating in contact with aggressive media at temperatures ranges from minus 50 °C up to +50 °C and air at temperatures ranges from minus 50 °C up to +150 °С.
Index name CIATIM-205 VNİİ NP -279
Compliance with classifi cations NLGIDIN 51502
5K5C-60
1K HC 1 N-50
Appearance Homogeneous oily ointment from white to light cream color, small granularity is
allowed.
Bright homogeneous
transparent ointment of a
smooth structure
Thickener Organic Inorganic
Operating temperature range, min…max, °С -60..+ 50ºC -50..+50ºC (+150)
Dropping point, °С, not less than 65 -
Penetration at 25°С, mm·10−1 165 -
Shear strength, Pa, within:, - 100
Colloid stability, %, not more than 4 5,2
Effective viscosity with average gradient of the strain rate 10 s−1, Pa·s, not more than - 2300 (-30ºC)
Chemically resistant lubricantsREFERENCE BOOK
117
Grea
se
Che
mic
ally
resi
stan
t lub
rica
nts
TS U 24.6-30802090-068:2007
VNII NP-282 A and VNII NP-282M A are designed for designed for sealing and lubrication of the friction surfaces of various units of equipment operating at different loads in contact with corrosive environments and gaseous oxygen. Greases are allowed to use at temperatures up to minus 60°C in powerful mechanisms, valves and oxygen breathing equipment.
Greases have an increased resistance to oxygen and aggressive environments (acids, amines, hydrazine), and lower resistance to prolonged contact with nitric acid and hydrogen peroxide.
Index name VNİİ NP -282 A VNİİ NP -282M A
Compliance with classifi cations NLGIDIN 51502
3KFK 3 N-45
3KFK 3 N-45
Appearance Homogeneous ointment with smooth structure from white to light gray in
color
Thickener Inorganic
Operating temperature range, min…max, °С -45 (-60)..+ 150ºC
Penetration at 25°С, mm·10−1 Not specifi ed
Shear strength, Pa, within:, 50ºC 200-700 Not more than 200
Colloid stability, %, not more than 5 10
Effective viscosity, Pa·s, not more than• At (50°С) (average gradient of the strain rate 1000 s-1),• At (–20°С) (average gradient of the strain rate 10 s-1)• At (–30°С) (average gradient of the strain rate 10 s-1)
Not less than 1,6-
2000
Not more than 1,0
1200-
Evaporation at 150°С within 1 hour, %, not more than 5
REFERENCE BOOK
118
Grea
se
Dril
ling
lubr
ican
ts
Drilling lubricants
TS U 23.2-30802090-036:2005
Drilling grease Agrinol Dolotol AU is used in drilling rigs for lubrication of friction units of chisels with hermetic sliding supports and for conserving chisels during the storage.
TS U 23.2-30802090-116:2011
Drilling grease Agrinol Dolotol N is used for greasing and encapsulation of friction units of rollercone drill bits with unpressurised support of rolling and sliding and for conservation of drill bits during storage. Contains graphite and molybdenum disulfide. Grease does not contain chlorine compounds.
Grease is sufficient in different climatic zones and temperatures from minus 20 °С up to +150 °С.
Index name Agrinol Dolotol АU Agrinol Dolotol N
Compliance with classifi cations NLGIDIN 51502
0/1KPF 0/1 T-30
2/3KPF 2/3 N-20
Appearance Homogeneous smooth ointment
black color
Homogeneous ointment black
color
Thickener Ca complex Li
Operating temperature range, min…max, °С -30..+ 220ºC -20..+150
Penetration at 25°С, mm·10−1 320-370 230-280
Effective viscosity at 0°С with average gradient of the strain rate 10 s−1, Pa·s, not more than 800 1000
Shear strength, Pa, within: 100 (50ºC) 200 (80ºC)
Colloid stability, %, not more than 12 10
Water resistance, class, not less than 1b 1b
Tribological characteristics on 4 balls machineat (20±5) °С, N, not less than• Welding load• Critical load• Scuff index
82321039735
7840872735
REFERENCE BOOK
119
Grea
se
Low
-tem
pera
ture
lubr
ican
ts
Low-temperature lubricants
GOST 11110–75
Ciatim-202 - plastic frost-resisting lubricant is used for greasing of frictionless bearings (gyroscopic devices of bearing rotor and other high-speed instrument bearings) working at the temperature range from minus 50°С up to 120°С.
GOST 8773–73
Ciatim-203 - plastic anti-friction grease for lubrication of mechanisms operating at high specific loads.
Grease is designed to lubricate gears, worm gear reducers, sliding bearings and roller bearings, various actuators, screw pairs, gearboxes, friction units of cars.
Index name CİATİM-202 CİATİM-203
Compliance with classifi cations NLGIDIN 51502
2K2K-50
2KP2E-50
Appearance Homogeneous ointment without lumps from light yellow to light
brown color
Homogeneous ointment dark green or brown
Thickener Li
Operating temperature range, min…max, °С -50..+ 120ºC -50..+90ºC
Dropping point, °С, not less than 175 160
Penetration at 25°С, mm·10−1 265-325 250-300
Shear strength, Pa, within:, 50ºC 150 250
Colloid stability, %, not more than 20 10
Effective viscosity, Pa·s• At (50°С) (average gradient of the strain rate 1000
s-1), not less than• At (–30°С) (average gradient of the strain rate 10
s-1), not more than
-1300
11000
REFERENCE BOOK
120
Grea
se
Rop
e gr
ease
s
Rope greases
TS U 23.2-30802090-110:2009
PROTECTING TG grease is designed for protection of steel ropes against wear and corrosion (including ropes in underground and surface mining equipment) in the process of manufacture and during transportation and operation.
Index name PROTECTING TG
Appearance
Homogeneous ointment from brown to black color without foreign
impurities
Thickener Solid hydrocarbons
Operating temperature range, min…max, °С –35 … +50
Kinematic viscosity at 100°С, mm²/s, not less than 16,0
Temperature, °С: • Open cup fl ash point, °С, not less than • Dropping point
15062-72
Low temperature properties at −35°С Pass
Pouring time, s, not more than 6
Thermal stability • Preservation of structural homogeneity Pass
Adhesive ability (discharge in centrifuge with separation factor Кр = 6270), %, not more than 50
Protective ability of steel mk 10 in electrolyte solution, days, not less than 5
Rope greasesREFERENCE BOOK
121
Grea
se
Rop
e gr
ease
s
TS U 23.2-30802090-115:2009
Agrinol Rope 39U is designed for the lubrication of wire ropes (against corrosion and premature wearout during operation), including mining and drilling ropes, working in temperatures ranging from minus 25 °C to +50 °C.
Index name Agrinol Rope 39U
Appearance Homogeneous ointment from brown to black
Thickener Solid hydrocarbons
Operating temperature range, min…max, °С -35..+50
Conventional viscosity at 100 °С, conditional degrees, not less than 4,5
Dropping point, °С, within 65-78
Low-temperature properties at minus 25°С Pass
Corrosive effect on metals Pass
Thermal stability• Appearance• Evaporation, %, not more than
Pass0,2
Mass fraction:• Water soluble acids and alkalis, %, not more than• Water, %, not more than• Abrasive mechanical impurities, %, not more than
NoneNoneNone
Rope greasesREFERENCE BOOK
122
Grea
se
Rop
e gr
ease
s
TS U 23.2-30802090-053:2006
Agrinol Torsiol-35B/1 is used as a greasing material in production of steel ropes.
Agrinol Torsiol-35B/2 is used for conservation of steel ropes and their protection from inclement weather.
Agrinol Torsiol-35E is intended for lubrication of steel ropes (including ropes of surface and underground lift systems of mines) under operating conditions. Product can be used for greasing in process of manufacturing of steel ropes, used to operate under extremely low temperatures: from minus 35°С up to +50°С.
Index name Agrinol Torsiol-35B/1
Agrinol Torsiol-35B/2
Agrinol Torsiol-35E
Appearance Movable mass from brown to dark brown color
Thickener Solid hydrocarbons
Operating temperature range, min…max, °С -35..+50
Kinematic viscosity, mm²/с• At 50°С• At 100°С
-Not less than 8,5
--
10-20-
Temperature, °С:• Open cup fl ash point, °С, not
less than• Dropping point
180
65-80
180
70-80
180
-
Low-temperature properties at minus 35°С Pass -
Thermal stability• Preservation of structural
homogeneity• Evaporation, %, not more than
Pass
0,2
Pass
0,7
-
-
Adhesive ability, %, not more than 60 30 -
Protective ability of steel mk 10 in electrolyte solution, days, not less than
- 5 -
REFERENCE BOOK
123
Grea
se
Inst
rum
enta
l lub
rica
nts
Instrumental lubricants
GOST 6267–74
CİATİM-201 - lithium anti-friction frost-resisting and refractory lubricant is used for greasing of easy-loaded rolling and sliding friction units. The lubricant is intended for greasing friction units of aircrafts, radio engineering equipment, electromechanical and other devices and precision mechanisms, main units of cars and other ground machinery exploited in northern regions and working with a small shearing force under the easy loads.
GOST 18179–72
OKB-122-7 grease is used in ball bearings and other friction units working in the temperature range from minus 60 °C to 120 °C.
Index name CİATİM-201 OKB 122-7
Compliance with classifi cations NLGIDIN 51502
2K2E-60
2KSi2K-60
Appearance Homogeneous ointment without lumps from light yellow to light brown color
Thickener Li
Operating temperature range, min…max, °С -60..+90 -60..+120
Dropping point, °С, not less than 175 -
Shear strength at 50°С, Pa, not less than 250-500 Not less than150
Colloid stability, %, not more than 26 10
Effective viscosity, Pa·s* at 50°С (average gradient of the strain rate 10 s-1)* -at 50°С (average gradient of the strain rate 10 s-1)
-
1100
1,2
-
REFERENCE BOOK
124
Grea
se
Mar
ine
lubr
ican
ts
Marine lubricants
GOST 2712-75
Water-resistant conservation greases of АМS series are used for lubrication of various mechanisms (of ships, submarines, hydroplanes), which are working in water (including the sea water) in the temperature range from -15°C to 70°C.
Index name AMS-1 AMS-3
Compliance with classifi cations NLGIDIN 51502 1 K1E-15 3/4 K3E-15
Appearance Homogenous smooth ointment from dark color without lumps
Thickener Al Al
Operating temperature range, min…max, °С -15..+70 -15...+70
Dropping point, °С, not less than 100 100
Effective viscosity at 0°С with average gradient of the strain rate 10 s-1, Pa·s, not more than 1000 2000
Penetration at 25°С, mm·10−1 300-350 200-250
Testing of protective properties for 24 hours Pass
Water soluble acids and alkalis None
Water content None
Mechanical impurities None
REFERENCE BOOK
125
Grea
se
Con
srev
atio
n (p
rote
ctiv
e) lu
bric
ants
Consrevation (protective) lubricants
TS U 23.2-30802090-063:2006
Agrinol ZES grease is used for protection of ground wires and armatures of high-voltage power lines from corrosion. Product also can be used in various machines, mechanisms and other metal products made of ferrous and non-ferrous metals in various conditions (such as: operating, transportation and storage in open areas).
The lubricant can be used in all climatic zones, including the dry and humid tropics, sea fog, contact with fresh and sea water, as well as under direct impact of sunlight beams.
GOST 19537–83
Cannon Grease is used for corrosion protection of metal products surfaces at the temperature ranges from minus 50°С up to +50°С in storage and conservation conditions.
Index name Agrinol ZES Cannon Lubricant
Compliance with classifi cations NLGIDIN 51502
1/2OG 1/2 G-50
5/6M 5/6 C-50
Appearance Ointment without lumps of dark color
Homogeneous ointment, from yellow to brown
color
Thickener AlHydrocarbonic Hydrocarbonic
Operating temperature range, min…max, °С -50..+100 -50...+50
Dropping point, °С, not less than 105 60
Sliding temperature, °С, not less than - 50
Penetration at 25°С, mm·10−1 270-335 90-150 (without stirring)
Determination of tendency to sliding Pass -
Corrosive effect on metals Pass Pass (copper)
REFERENCE BOOK
126
Grea
se
Sea
ling
lubr
ican
ts
Sealing lubricants
TS U 24.6-30802090-034:2005
Agrinol Kranol is a sealing grease for gas valves used for lubrication of shutoff valves of gas appliances, shutoff valves of gas pipelines, gas distribution and compressor stations at the pressure of 7.5 MPa
GOST 19538–74
ZZK-3u is used for cracks in hatches, lids, doors and other places of machines, as well as in conservation of machine tools and other equipment, concealed with housings, sheaths, and shields.
GOST 16862–71
Antifrictional conservation and sealing lubricant VNII NP-263 is intended for sealing of threaded connections, screwing out threads for operation in extreme temperature conditions.
Index name Agrinol Kranol ZZK-3u VNİİ NP-263
Compliance with classifi cations DIN 51502 - - MP G-50
Thickener Ca Al Inorganic
Operating temperature range, min…max, °С 0..+50 -60..+80 -50...+100
Dropping point, °С, not less than 60 115 -
Colloid stability, %, not more than 2,0 - 10
Penetration at 25°С, mm·10−1, without stirring 35-70 40-80 Not specifi ed
Shear strength at 50°С, Pa, not less than - - 100
Tendency to sliding at 100 °C- Pass -
Corrosive effect on metals Pass
Sealing lubricantsREFERENCE BOOK
127
Grea
se
Sea
ling
lubr
ican
ts
TS U 23.2-30802090-121:2009
Grease Agrinol LZ-162u is intended for sealing of the valves (direct-flow valves, plug valves), flowing oil and gas wells, including deep and ultra-deep pressure on downhole of up to 100 MPa.
TS U 24.6-30802090-123:2009
Grease Agrinol Armatol-238 is used for the sealing of the locking devices of mining oil industry equipment from oil, gas and gas condensate fields, which contain hydrogen sulfide and carbon dioxide to 25 % by volume and operated in all climatic zones (including areas with cold climates), as well as for various other valves.
TS U 23.2-30802090-125:2009
Agrinol Rezbol ОМ-2 grease is intended for sealing and corrosion protection of various pipes: casing, tubing and drilling in the construction and operation of oil and gas rigs.
Index name Agrinol LZ-162u
Agrinol Armatol-238
Agrinol Rezbol OM-2
Compliance with classifi cations NLGIDIN 51502
4/5MF 4/5 K-40
0/1MF 0/1 K-50
0/1MPF 0/1 S-50
Thickener Li-Zn Inorganic Li
Operating temperature range, min…max, °С -40..+130 -50..+120 -50..+200
Dropping point, °С, not less than 149 160 -
Penetration at 25°С, mm·10−1, 150-200 300-360 330-390
Effective viscosity at 0°С with average gradient of the strain rate 10 s-1, Pa·s, not more than 1500 1000 1000
Colloid stability, %, not more than 6 15 10
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than:• Welding load - - 6174
Water resistance, class, not less than 1b 1b -
Corrosive effect on metals Pass (steel)
REFERENCE BOOK
128
Grea
se
Red
ucer
lubr
ican
ts (s
emi-f
luid
)
Reducer lubricants (semi-fl uid)
TS U 23.2-30802090-026:2004
Transol-100А grease is designed for greasing of worm gearboxes and geared motors, working with the maximum specific loads up to 400 MPa.
Transol-200А grease is designed for lubrication of cylindrical and planetary gear reducers and gearmotors, working with the maximum specific loads up to 2000 MPa. Product is efficient for at least 10 000 hours.
GOST 16422–79
Ciatim-208 semi-fluid transmission lubricant is needed for greasing of heavily loaded gear reducers of tracked vehicles.
Index name Transol-100A Transol-200A CİATİM-208
NLGI Compliance with classifi cations DIN
51502
00 GHCF00G-40
00 GP00E-40
1 GP1H-30
Appearance Homogeneous smooth ointment from light brown to dark brown
color
Homogeneous viscous black
liquid
Thickener Li Ca
Operating temperature range, min…max, °С -40..+110 -40..+70 -30..+100
Dropping point, °С, not less than 150 -
Effective viscosity at 0°С with average gradient of the strain rate 10 s-1, Pa·s, not more than
1200 1400 1800 (dynamic, at minus 30°С)
Penetration at 25°С, mm·10−1400-430 385-430 300-360 ((–15°С)
Without stirring)
Colloid stability, %, not more than, 10-35 10-30 -
Evaporation, %, not more than 1,5 (100ºC) 0,8 (100ºC) 15,0 (125ºC)
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than• Welding load• Critical load• Scuff index
1744696343
2764696392
6938872764
REFERENCE BOOK
129
Grea
se
Bra
ke-
in p
aste
s
Brake- in pastes
TS U 23.2-30802090-052:2006
Agrinol Limol А grease is designed to facilitate the assembly, running-in and lubrication of slide bearings, hinges of helical and toothed gears, heavy-duty low-speed friction units, threaded connections.
GOST 19782–74
VNII NP-225 is designed for protection of threaded connections form seizure at the temperature ranged from minus 60°С up to +250°С for aluminum anodized alloys and up to 350°С for stainless steels, as well as for low-speed heavy-duty friction units at the temperatures from minus 40°С up to +300°С.
GOST 14068–79
VNII NP-232 is designed for lubrication of splines and running threads at the temperatures up to +300°С, and for the threaded connections that are fixed during operation of the unit - up to +400°С.
Index name Agrinol LimolA VNİİ NP-225 VNİİ NP-232
Compliance with classifi cations NLGIDIN 51502
1KF 1U-50
00KsiF 00 U-60
3KF 3 U-50
Thickener Inorganic Inorganic Li
Operating temperature range, min…max, °С -50..+300 -60..+300 -60..+300
Dropping point, °С, not less than 240 - -
Penetration at 25°С, mm·10−1 6,0 - 4
Corrosive effect on metals Pass Pass (3 hours, 250°С) Pass
Tribological characteristics on 4 balls machine at (20±5) °С, N, not less than• Welding load• Critical load• Scuff index
32832195755
---
---
REFERENCE BOOK
130
Grea
se
Insu
latio
n lu
bric
ants
Insulation lubricants
TS U 24.6-36451680-143:2010
Hydrophobic filler Agrinol Hydrophobinol-І is designed for filling the shell of communication cables in order to prevent the ingress of moisture into the cable.
Hydrophobic filler Agrinol Hydrophobinol-І is ready for use in the delivery condition, requires no dilution and can be warmed up for the complete filling of the cable sheath.
Index name Agrinol Hidrofobinol-I
Thickener Hydrocarbonic
Kinematic viscosity at 100 °С, mm2/s, within 20,0 – 50,0
Dropping point, °С, not less than 70-95
Flash point in open crucible, °С, not less than 180
Density at 20°С, g/cm3, within 0,860-0,890
Shrinkage, %, within 4-6
Change in isolation mass, %, not more than 15
Volume resistivity, Om/cm3:• At 20°С, not less than• At 100°С, not less than
1*1016
1*1012
Dielectric permittivity:• At 20°С and 1kHZ frequency, not more than• At 20°С and 1mHZ frequency, not more than
2,32,3
REFERENCE BOOK
134
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
Cooling lubricants, manufactured by “Agrinol” are complex, multicomponent systems, which are used in cooling process of metalworking tools and bench parts. Reduction of temperature in the working area reduces wear-out of the cutting tool, and, consequently, the quality and accuracy of the machined surface is increasing. It is also important to provide the protection against corrosion of the cutting tool, workpiece and the rolled sheet during manufacturing and storage.
Efficiency of “Agrinol” cooling lubricants application is determined by the high degree of concentrated coolant dilution and low specific consumption of the solution per workpiece unit.
The wide range of “Agrinol” cooling lubricants allows you to choose the most effective coolant for each combination: the processed material — type of processing — instrumental material — cutting mode.
REFERENCE BOOK
135
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
O
il co
olan
ts
Oil coolants
GOST 38.01445–88
MR-7, MR-7V are used as cooling lubricants for blade machining, including vending machines and benches, arbon, alloy, stainless and heat resistant steels, as well as some hard-alloys. Limitedly applicable in processing of copper and its alloys. Feeding to the cutting are is performed through irrigation or under the pressure.
TS U 24.6-30802090-056:2006
Technological greases Agrinol KЕT-1 and Agrinol KЕT-1M are used in calibrating of tubes by expanders.
Index name MR-7 MR-7B Agrinol КEТ-1 Agrinol КEТ-1M
Flash point in open crucible, °С, not less than 180 -
Kinematic viscosity at 100°С, mm2/s 23-30 -
Saponifi cation number, mgКОН/g, not less than 18 15
Acid number, mg КОН/1g, not more than 1,2 -
Color, CNT units, not more than - 2 -
Corrosive effect on metals Pass Pass
Mass fraction, %:• Mechanical impurities, not
more than• Water, not more than• Sulfur• Free organic acids, not
more than
0,04None
1,2-2,0-
-45-7
-38-7
Oil coolantsREFERENCE BOOK
136
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
O
il co
olan
ts
TS U 24.6-36451680-161:2011
TL Effort stamping grease is designed for wide range of operations: in the automotive industry during cold plate and volumetric forging of structural and alloyed steels (special deep drawing of steels, forming, calibrating, fine cutting, binding on automated presses), as well as during the rolling of threads and threading in manufacturing of metal products and pipes.
Environmentally friendly product! Product does not contain Cl and Р (Chlorine and Phosphorus) and synthetic
biologically undegradable substances.
Index name TL Effort
Kinematic viscosity at 50°С, mm2/s 90
Saponifi cation number, mgКОН/g, not less than 60
Corrosive effect on metals:* on ferrous metals (iron, steel)* on non-ferrous metals (copper)
Pass3а-4с
Mass fraction of sulfur, %, not more than 2,8
Mass fraction of water, %, not more than 0,5
Flash point in open crucible, °С, not less than 190
Content of mechanical impurities, %, not more than 0,08
REFERENCE BOOK
137
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
W
ater
-bas
ed c
oolin
g lu
bric
ants
Water-based cooling lubricants
TS U 24.6-30802090-139:2010
Technological grease Agrinol TEMP-3KN is used in form of (6-10) % water emulsions for oiling of carbon steels after etching prior to cold rolling.
For preparation of emulsions can be used water with hardness not more than 6 mg-eq / dm3.
TS U 23.2-30802090-105:2011
Water-based cooling lubricant Cold Roller is used in form of (2-10) % water emulsions on the stage of cold rolling of steel and oiling of steel straps before wrapping them in a roll. Has increased lubricating, antiwear, anti-corrosive properties. Resists carbon formation.
Environmentally friendly product!Does not contain CL and synthetic non-biodegradable substances!
Index name Agrinol TEMP-3KN Cold Roller
Kinematic viscosity at 50°С, mm2/s - 30
Saponifi cation number, mgКОН/g, within - 65-90
Dropping point, °С, within 35-45 -
Acid number, mg КОН/g, within, within 100-150 16-25
Mass fraction of water, %, not more than 5,0 1,0
Storage stability - Pass
10 % working emulsion 3% working emulsion
рН value, рН units, within - 8,0-9,0
Stability, % Pass Pass (for 6 hours)
Corrosive effect on metals Pass Pass
Water-based cooling lubricantsREFERENCE BOOK
138
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
W
ater
-bas
ed c
oolin
g lu
bric
ants
GOST 5702–75
Technological lubricant SP-3 is designed for use as an aqueous emulsion in rolling of nonferrous metals and as a working fluid in hydraulic systems of technological equipment.
TS U 23.2-30802090-025:2004
TS U 23.2-30802090-022:2003
Agrinol EHP and Agrinol HP technological lubricants are intended for use in form of (2 5)%-aqueous emulsions (with hardness up to 5 mg-eq/dm3) at the stage of cold rolling steel, and in form of (5-10)%-aqueous emulsions (with hardness up to 17 mg-eq/dm3) - for oiling of the steel stripes before wrapping them in a roll with following thermal treatment.
Both products can be used in the processing of ferrous metals by pressure or cutting.
Index name SP-3 Agrinol EHP Agrinol HP
Kinematic viscosity at 50°С, mm2/s - 50 35
Alkaline number, mg КОН/g, not less than 7 -
Acid number, mg КОН/g, within 17-21 not more than 16
not more than 12
Corrosive effect on metals Pass -
Mass fraction of water, %, not more than None 1
Storage stability - Pass
Working emulsion 3 %
рН value, рН units, within - 8-9
Stability within 6 hours, %, not more than - Pass
Corrosive effect on metals - Pass
Water-based cooling lubricantsREFERENCE BOOK
139
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
W
ater
-bas
ed c
oolin
g lu
bric
ants
TS U 23.2-30802090-048:2006
Emulsol Agrinol OM is used in metal cutting and cold-rolling of structural steel.
Emulsol is applied in form of 5 %-water emulsion during cold-rolling of structural steel, including automotive sheets.
Product also can be applied in form of (3-5)%-water emulsion during the processing of carbon and alloy steels in grinding, turning, drilling, and other operations.
TS U 24.6-36451680-091:2010
KAS-1SM liquid is designed for preparation of (3-5)%-aqueous emulsions, which are used in the processing of ferrous metals with cutting and grinding. For the preparation of emulsions can be used water with hardness up to 17 mg-eq/dm3.
TS U 23.2-30802090-005:2003
Emulsol Agrinol ET-2U is a concentrate of oil-coolant, which is used in form of (3-10)% emulsions during the cutting and abrasive machining of cast iron, carbon and alloy steels.
Index name Agrinol OM Agrinol EТ-2U KAS-1SM
Kinematic viscosity at 50°С, mm2/s 15-50 20-50 100
Saponifi cation number, mg КОН/g, within 22-45 - -
Acid number, mg КОН/g, within - 15-23 -
Mass fraction of free organic acids, mg КОН/g of emulsifi er, within 18-25 - -
Mass fraction of water, % 3,0 3,0 -
Storage stability Pass
Working emulsion 5% 10% 2%
рН value, рН units, within 7-9 8-10 8-10
Stability, %, not more than 1,0 0,5 (4 hours) Pass (6 hours)
Corrosive effect on metals Pass
Water-based cooling lubricantsREFERENCE BOOK
140
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
W
ater
-bas
ed c
oolin
g lu
bric
ants
TS U 23.2-30802090-054:2006
TS U 23.2-30802090-051:2006
Agrinol Akvol-2 and Agrinol Akvol-2E are liquid coolants used in the processing of doped, stainless, heat-resistant alloys and steels.
Liquids are used for the preparation of (3-10)% emulsions, which are used in the processing of doped stainless, heat resistant steels and alloys on the operations of turning, drilling, milling, reaming, threading, broaching, heavy-duty grinding, as well as for processing of aluminum alloys with cutting.
Index name Agrinol Akvol-2 Agrinol Akvol-2E
Kinematic viscosity at 50°С, mm2/s 40-80 40-100
Saponifi cation number, mg КОН/g, within 20-45 20-45
Acid number, mg КОН/g, within 10 12
Mass fraction, %* Water, not more than* Sulfur,within* Chlorine, within
51,5-2,8
4-5
51,5-2,8
-
Working emulsion 7%
рН value, рН units, within 8-10
Stability, %, not more than Pass
Corrosive effect on metals Pass
Water-based cooling lubricantsREFERENCE BOOK
141
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
W
ater
-bas
ed c
oolin
g lu
bric
ants
TS U 24.6-30802090-083:2009
Synthetic hydraulic fluid RG-s is used in hydraulic systems of various industrial and mining equipment (hydraulic powered supports, hydrotravellers, conjugation linings, etc.) in form of (1,0 - 5)%-water emulsion at environmental temperatures above 10°С.
RG-1s is designed for moderate operating modes, RG-2s is designed for heavy-loaded systems.
Emulsion can be prepared in water with any hardness index (up to 20-25 mg-eq/dm3), including mine waters. It does not contain chlorine.
Index name RG-1s RG-2s
Kinematic viscosity at 50°С, mm2/s 15 20
Density at 20°С, kg/mm³, within 1000-1200 1100-1300
Concentrate stability during the storage Pass
Working emulsion 1% 0,75%
рН value, рН units, within 8,5-10,0
Corrosive effect on metals Pass
Water-based cooling lubricantsREFERENCE BOOK
142
TECH
NO
LOGI
CAL
CO
OLI
NG
LUB
RICA
NTS
W
ater
-bas
ed c
oolin
g lu
bric
ants
TS U 23.2-30802090-020:2002
Agrinol RG working fluid is used in hydraulic systems of industrial equipment and is primarily intended for using in form of (3-5)%-water emulsions in hydraulic systems of minig equipment (including underground equipment), at the environmental temperatures above 10°С.
TS U 23.2-30802090-042:2005
Emulsol Agrinol EKS-5 is a concentrate, which can be used as a 10 %-aqueous emulsion in water with the hardness not more than 6 mg-eq / dm3 with addition of 0,2 % of soda ash added for greasing of metal molds during the production of concrete products. Emulsifier facilitates removal of concrete and concrete products of the metal forms by reducing the adhesion (sticking) to metal products. Product can be used in pure form.
Index name Agrinol RG Agrinol EKS-5
Kinematic viscosity at 50°С, mm2/s, not more than 100 50
Acid number, mg КОН/g, within not more than 16 8-12
Mass fraction, %, not more than* Water, not more than* Chlorine, within
50,3
Traces-
Storage stability Pass -
Working emulsion 10%
рН value, рН units, within 8-10 -
Stability, %, not more than ≤0,5 (4 hours) Pass (2 hours)
Corrosive effect on metals Pass -
REFERENCE BOOK
146
AUTO
CH
EMIS
TRY
One of the most important elements of engine support is coolant. Improper quality of coolant can lead to the corrosion of metal parts of the engine and solders, as well as swelling of nozzles.
Coolants of “Agrinol” production (such as TOSOL) contain anticorrosive, stabilizing, antifoaming and coloring components in their structure. Special additives provide “Agrinol” coolants win a unique set of properties that allows you to use them as long as possible with great efficiency and without losing these properties.
Coolants of “Agrinol” production provide high cooling efficiency, reliability and durability of the engine in general.
REFERENCE BOOK
147
AUTO
CH
EMIS
TRY
Coo
ling
liqui
ds
Cooling liquids
TS U 24.6-30802090-130:2009
Agrinol Tosol cooling liquids are designed for cooling of an internal combustion engines, as well as the working fluid in the other heat exchangers operating at low and moderate temperatures. Agrinol Tosol can be used both in copper and in aluminum radiators. It should be poured directly into the cooling system. Fluid is designed for operation without replacement and without addition of any additives during 60,000 km or for 2 year period.
Temperature range for:Agrinol Tosol-30 — intended for southern regions, where environmental
temperature is not lower than minus 30°С.Agrinol Tosol-40 — regions, where environmental temperature is not lower
than minus 40°С.Agrinol Тosol-65 — regions of Far North, where environmental temperature
is not lower than minus 65°С. Can also be used as a concentrate for preparation of a coolant with specified freezing point.
Index name Agrinol Tosol-30
Agrinol Tosol-40
Agrinol Tosol-65
Crystallization temperature, °С, not more than -30 -40 -65
РН level, рН units, within 7,5-11,0 7,5-11,0 7,5-11,0
Corrosive effect on metals, g / m2*24 hours, not more than:• Copper, cast iron, brass, steel• Solder• Aluminum
0,20,30,5
0,20,30,5
0,20,30,5
Rubber swelling, %, not more than 5
Alkalinity, cm3, not less than 10
Density at 20°С, kg / m3, within 1055-1125 1065-1135 1085-1145
Cooling liquids REFERENCE BOOK
148
AUTO
CH
EMIS
TRY
Coo
ling
liqui
ds
TS U 24.6-30802090-130:2009
Coolant Agrinol Tosol ТА is used in south regions with environment temperature not lower than minus 20°С.
Coolant Agrinol Tosol А-40 is used in south regions with environment temperature not lower than minus 38°С.
Fluid could be used in both copper and aluminium radiators. Fluid is intended for expluatation without change and admixture of any additives during 60000 km for 2 years. Fluid should be filled into cooling system.
Index name Agrinol Tosol TA Agrinol Tosol A-40
Crystallization temperature, °С, not more than -21 -38
Pour point, °С, not more than -23 -41
РН level, рН units, within 7,5-11,0 7,5-11,0
Corrosive effect on metals, g / m2*24 hours, not more than:• Copper, cast iron, brass, steel• Solder• Aluminum
0,10,20,1
0,10,20,1
Rubber swelling, %, not more than 5
Alkalinity, cm3, not less than 10
Density at 20°С, kg / m3, within 1055-1125 1065-1125
Foaming:• Amount of foam, cm3, not more than• Foam stability, s., not more than,
303
303
REFERENCE BOOK
149
AUTO
CH
EMIS
TRY
Win
dshi
eld
flui
ds
Windshield fl uids
TS U 24.5-36451680-158:2010
Crystal windshield fluids can be used for cleaning the glass, headlights and mirrors from ice, mud and insects; as well as a glass anti-fog. Fluids can be used in all seasons, manually or with use of the washer.
Crystal windshield fluids can be used domestically for cleaning glass, mirrors, crystal items, porcelain, pottery and ceramics (excluding food dishes).
Depending on operating conditions and the temperature of crystallization several brands of liquids are offered: Crystal-2; Crystal-5; Crystal-16; Crystal-20; Crystal-25; Crystal-32; Crystal-50
Index nameCrystal
2 5 16 20 25 32 50
Appearance at the temperature of (20 ± 5) °С
Homogenous transparent liquid without mechanical impurities
Density at 20°С, kg / m3, within
900-1000
900-1000
850-980
850-980
850-980
850-980
850-980
Crystallization temperature, °С, not more than
-2 -5 -16 -20 -25 -32 -50
РН level, рН units, within 6-9 6-9 6-9 6-9 6-9 6-9 6-9
Environmental temperature,°С Amount of preparation, dm³ Amount of distilled water,dm³
Up to minus 5°С 1 5
From minus 5°С up to minus 10°С 1 3
From minus 10°С up to minus 20°С 1 1,5
From minus 20°С up to minus 40°С 1 1
REFERENCE BOOK
152
Met
al p
acki
ng
Metal packing
“Scientific and Industrial Enterprise (SIE) Agrinol” is a manufacturer of meta drums for oil, chemical, food products etc. Manufacturing of drums is effected on modern technological lines in accordance with health and ecological requirements High fexibility of manufacturing ensures competitive price along with high quality product. Quality management system DSTU ISO 9001 – 2001 (ISO 9001 – 2001) have been implemented, drums manufactured comply with Government Standards (GOST), Technical Specifcations and International transportation rules for dangerous goods by UN.
Production of metal packing with the logoAccording to individual order, the drum may be painted in any color or framed
in accordance with customer’s design, including costumer’s logo or trademark on the drum body that will ensure your packaging original and recognizable appearance:
PAINTING OF METAL DRUMS
Metal packingREFERENCE BOOK
153
Met
al p
acki
ng
Steel drum, tight-head type 1A1L 216,5 dm3
• The First neck — fl ler neck G2’’, Rieke, made by curling.• The second neck — Air-hole G3 / 4’’, Rieke, made by curling.• Curling — round seven-layer seam with sealing hermetic Darex 159 V.• Drum’s body is made of sheet metal, thickness 0,9 – 1,0 mm.• Edges-ridge — Two ridges that are made on the surface of the drum’s
frame with radius R = 9 mm.• The dense, strong and tight welding seam is made by contact welding
overlapped width of 4 mm• Bottom and top are made of sheet metal thickness of 1,0 mm.
Barrel with food internal cover .• Possible to produce
Steel drum, open-head type 1A2L 213 dm3
• Hoop Coupling — “Agrinol” production, made of galvanized metal.• The lock with lever, Rieke production, is supplied with a device for
sealing plastic cotter.• The removable deep-drawing top 1,0 mm thick with relief.• Drum’s body is made of sheet metal thickness 0,9 – 1,0 mm.• Edges-ridge — Two ridges that are made on the surface of the drum’s
frame with radius R = 9 mm.• The dense, strong and tight welding seam is made by contact welding
overlapped width of 4 mm.• The bottom is made of sheet metal thickness of 1,0 mm with a rigid relief.
It is connected to the seven-layer seam with sealing hermetic Darex 159V.
Metal packingREFERENCE BOOK
154
Met
al p
acki
ng
Drum CD-1A2 18 20 dm³• Thickness of upper and lower metal bottom: 0.28 mm.• Thickness of the bucket body: 0.30mm.• Capacity: 20 dm3.• Weight of the empty drum: 1.5 kg.• Body: welded• The mass limit for packaged product: 30kg.
REFERENCE BOOK
155
Corr
espo
nden
ce t
able
pro
duct
s
Correspondence table products
NAME TYPE NLGI ANALOGS
General-purpose lubricants
Agrinol SolidolZh- 0, Zh-1, Zh-2, Zh-3
Са 0,1,2,3 SHELL Ossagl V (00); TEBOIL Solid 0,2; EXXON Estan 1,2Cluber Lubrication Helveum 2; AGIP Grease CC 2,3BP Energrease C 1,2,3; SHELL Alvania RL 1,2,3
Fatty SolidolAgrinol Solidol ZhSH
Са 2 / 3
Agrinol Solidol EP-2,3 Са 2
3
TEXACO Novatex EP 2; EXXON Estan 2; SHELL Rhodina EP (LF) 2AGIP Grease CC 2,3; BP Energrease C 1,2,3
Graphite Grease Са+C 2 AGIP Grease NG; BP Energrease C-3G; SHELL Malleus STC 2
Konstalin-1Konstalin –2Agrinol 1 – 13
Na2 / 33 / 43 / 4
BP Energrease BRB N3; CASTROL Spheerol S, HSMOBIL GREASE BRB N3
Automobile lubricants
Agrinol LSC-15 Li 2 SHELL Alvania EP 2; MOBIL Mobillux 2, EP 2; ESSO Beacon EP 2
Agrinol Fiol-2УVNII NP-242 Li+Mo 2
BP Energrease L21-M / CL 2; CASTROL SPHEEROL LMMMOBIL grease SPECIAL / Mobilgrease XHP 2SHELL Retinax EPX / HDX 2 / Netia HV 2; Q8 Rembrant MolyPETROL OFISI Molibdenli gres 2; NESTE Allrex M 2 / Molygrease 2
Agrinol ShRUS-4 Li+Mo 2
BP Energrease LS-EP 2; SHELL Retinax HDX 2; 76 Megaplex XD; TEXACO Molytex EP 2; MOBILGREASE SPECIAL; Cluber Lubrication Caxtrobase MS 20; CHEVRON Moly Grease EP2; NESTE Molygrease 2; TEBOIL Universal M2; CASTROL MS / 3 Grease
Agrinol 158Agrinol 158М Li-K 1 / 2
NUCO Grease 57; SHELL Alvania RL 2; Q8 Rubens WB 2; NESTE Semilix 1,5 / Superlix EP2; ELF Epexelf 1,2; ZIC Wheel Bearing Grease 2
Agrinol ShRB-4 к-Ва 2 Cluber Lubrication Centoplex 132 BV
Multu-purpose lubricants
Agrinol Fiol 1 Li 1 BP Energrease L 1, 2; MOBIL Mobilux 1,2; SHELL Alvania RL 1,2CASTROL LM Grease; TEBOIL Multi-Purpose Grease 2
Agrinol Fiol 2 Li 2
Correspondence table productsREFERENCE BOOK
156
Corr
espo
nden
ce t
able
pro
duct
s
NAME TYPE NLGI ANALOGS
Agrinol Litol 24 Li 3
TEXACO Multifak Premium 3; SHELL Alvania RL / EP / Retinax EP;AGIP Grease MU 3; ESSO Beacon 3; MOBIL Mobillux 3.
Ligrease 00, 0, 1, 2, 3 Li 00,0,1,2,3
SHELL Alvania RL; MOBIL Mobillux; BP Energrease L; CASTROL LM Grease; TEBOIL Multi-Purpose Grease; TEXACO Multifak Premium; ESSO Beacon; ZIC Crown grease
Ligrease EP 00, 0, 1, 2, 3 Li+EP 00,0,1,2,3
SHELL Albida RL / EP1 / Retinax EP / LX / Alvania EP (LF) 1 / Starplex EP; MOBIL Mobillux EP; ESSO Beacon EP; ESSO Beacon; АZMOL Luvana EP / Lika EP; TEXACO Multifak EP; ZIC Crown grease EP
Railway lubricants
LZ-CNII Са-Na 3 / 4BP Energrease N 3; CASTROL Castrolease CS; MOBIL Mobilgrease BRB4; SHELL Alvania EP3 / Nerita 3
Agrinol GROAgrinol Buksol Li 3 / 4
2 / 3
SHELL Alvania RL 3; BP Energrease LS3; ESSO Beacon 3MOBIL Mobillux 3
Agrinol MZT k-Li 2 / 3 SHELL AeroShell Grease 6, 22; BP Energrease LS3; ESSO Beacon 3
Agrinol GT-72 k-Ca -SHELL AeroShell Grease 15AMOBIL Mobilgrease 24Agrinol GT-79L Li 2
Agrinol GTKZ-65 Li 2 / 3
Industrial lubricants
SKS HV1, HV1*SKS HV2, HV2*SKS 300m-1, 300m-1*SKS 300m-2, 300m-2*
Sulfonate Ca
1 / 22
1 / 22
AZMOL Sulena 1,2; TOTAL CERAN HVA 2 / FG276 Multiplex Red Grease 1,2;TEXSACO Polystar Syntetic 4602
ROLLING GR WROLLING GR S Ca 0 / 1
2SHELL Luveda EP2 / Alvania RL1,2 / Rhodina LF 2EXXON Estan 2; MOBILtemp 2; AGIP Grease CC 2,3BP Energrease C 1,2; TEXACO Novatex EP 2
Agrinol IP-1lAgrinol IP-1z Ca 1 / 2
0 / 1
LubriliCa WR 1, 2, 3 Li-Ca 1,2,3 SHELL Alvania WR; ELF EPEXELF; TOTAL Multis
2
Correspondence table productsREFERENCE BOOK
157
Corr
espo
nden
ce t
able
pro
duct
s
NAME TYPE NLGI ANALOGS
LubriliCa EP 1, 2, 3 Li-Ca+EP 1,2,3 SHELL Retinax HD2; ELF MULTIPLEX EP; TOTAL
Lical EP2; TOTAL Multiplex EP2 / Multis EP2
SLIDING GR 00, 0, 1, 2 k-Li
00012
BP Energrease LCX 222 / LC 1,2; CASTROL LMX; GULFcrown LC; ESSO Unirex S / Beacon EP; TOTAL Multis Complex EP2 / S2 A / ; NESTE Superlix EP2 / Semilix 1,5 / Allrex EP 1,2 / Yleisrasva EP 1,2; SHELL Albida HD / RL / EP / Retinax LX2 / Alvania EP (LF); TEBOIL Multi-Purpose HT; TEXACO Starplex EP / Hytex EPTEXACO Multifak Premium 3; MOBILlux EP; 76 Unoba EP Grease 1,2; АZMOL Luvana EP / Lika P
KLS Rolling k-Li 12
Agrinol ProkatOl-0Agrinol ProkatOl -2
k-Ca 0 / 11 / 2
EXXON Nebula 1; CASTROL Spheerol BN1;SHELL Darina 2 / Alvania RL / LF / WR1,2 / Luveda EP 2MOBILplekx 47 / Mobilux EP 2; TEBOIL Universal CLS-1;BP Energrease PR 9143
Agrinol Uniol-2М-1Agrinol Uniol-2М-2
k-Ca 12
Agrinol ProkatOl ЕР 2 k-Ca 1 / 2
TEXACO CX EP2; ELF Multiplex EP2; TEBOIL Universal CLS-1; SHELL Alvania RL / LF / WR1,2 / Luveda EP 2; TOTAL Copal EP2 / Multis Complex EP 2; BP Energrease PR 9143
Agrinol LKS k-Li+C 1 / 2SHELL Albida HDX 2 / Darina R 2; BP Energrease LCX 222; MOBILgrease HP 222; AGIP Grease SM 2
Agrinol Termostan k-Li+Мо 2 AGIP Grease SM2; MOBILlith SHC 1000 Spesial;
76 Megaplex XD Grease 2; SHELL Albida HDX 2
PLATING GR k-Li 2 / 3
BP Energrease LC / LCX 222 / 103; CASTROL LMX; MOBILlux EP2,3ESSO Unirex N 2,3 / S 2 / Beacon EP 2; GULFcrown LC 2NESTE Superlix EP2; Q8 Rubens WB 2 / 3; TEBOIL Multi-Purpose HTSHELL Albida RL2 / Alvania RL2,3TEXACO Starplex EP2,3 / Hytex EP2 / Multifak Premium 3
Correspondence table productsREFERENCE BOOK
158
Corr
espo
nden
ce t
able
pro
duct
s
NAME TYPE NLGI ANALOGS
Agrinol LS-1P Li 1
SHELL Albida RL / EP1 / Retinax EP / LX / Alvania EP (LF) 1 / Starplex EP 1ESSO Beacon EP1; BP Energrease LS-EP1; MOBILlux 1;.Q8 Rembrant EP 1; АZMOL Luvana EP 1 / Lika EP1,2;76 Unoda EP Grease 1
Heat-resistan lubricants
MOLYROLL GR 1MOLYROLL GR 2 Si+Mo 2
0
CHEVRON Moly Grease EP2; MOBILGREASE SPECIAL 2;ESSO Multy-Purpose Grease (Moly) 2; GULFlex Moly EP 2;NESTE Allrex M2 / Molygrease 2 / Avora 0; TEBOIL Universal M 2Q8 Rembrant Moly 2; SHELL Retinax SDX 2 / HDX 2 / Albida HDX 2;TEXACO Molytex EP 0,2;
Aerol-А Aerol -1А Si+Mo 20
EXXON Norva 275; ESSO Multy-Purpose Grease (Moly) 2MOBIL Mobiltemp 78 / Mobilgrease Special; TEBOIL Universal M 2TEXACO Molytex EP 0,2; NESTE Allrex M2 / Molygrease 2 / Avora 0;SHELL Retinax SDX 2 / HDX 2 / Albida HDX 2 / Rhodina EP 2
CIATIM-221 k-Ca 1 / 2 SHELL AeroShell Grease 15; Cluber Lubrication Asonic GHY 72
Agrinol Graphitol Si+C 2SHELL Albida HDX 2 / Rhodina EP 2; BP Energrease HTB;MOBILtemp 78 / Mobiltac 81
Agrinol VNII NP-219Agrinol VNII NP-210
к-Са+МоSi+Mo
0 / 11
NESTE Avora 0; 76 Triton XD5 Grease 0,1 / Megaplex XD Grease 1 TEXACO Molytex EP 0;
VNII NP-207 k-Ca 3 SHELL AeroShell Grease 15A, 22; Cluber Lubrication Asonic GHY 72
Chemically-stable lubricants
CIATIM-205VNII NP-279
OrganicSi
51 SHELL Petroleum Jelly S.6800 / Lipex OMB 2
Correspondence table productsREFERENCE BOOK
159
MET
AL P
ACKI
NG
Cor
resp
onde
nce
tabl
e pr
oduc
ts
NAME TYPE NLGI ANALOGS
Drilling lubricants
Agrinol Dolotol АU k-Ca 0 / 1 DRESSER SG-304
Low-temperature lubricants
CIATIM -202 Li 2SHELL AeroShell Grease 6, 22; BP Energrease LS 2; ESSO Beacon 2;MOBILgrease 28;
CIATIM -203 Li 2 SHELL AeroShell Grease 6, 22; MOBILtemp SHC 220;
Rope lubricants
PROTECTING TG
Solid hydrocarbons -
SHELL Malleus Fluid GL 65; MOBIL Turex 610
Agrinol Torsiol 35B
BP Energol BL 450 – 2; EXXON Surett N270k; SHELL Malleus Fluid GL 65; MOBIL-Kote 336
Agrinol Torsiol 35E MOBIL Turex 610
Instrument lubricants
CIATIM -201 Li 2 SHELL AeroShell Grease 6, 22; MOBILgrease 28 / Mobiltemp SHC 32
OKB-122-7 Li 2 BP Energrease LS 2; ESSO Beacon P 290, 2; SHELL AeroShell Grease 6, 22; MOBILlux 2
Conservation (protective) lubricants
Cannon Lubricant Solid hydrocarbons 5 / 6
SHELL AeroShell Compound 05; MOBIL-Kote 336;EXXON Rust-Ban 326; BP Petroleum Jelly PY 3
Agrinol ZESThe
hydrocarbon, soapy
1 / 2 BP Energrease A1; SHELL Mutilus A, B
Sealing-threaded
Agrinol Kranol Са - SHELL Aviation Grease S 7108; LUCINA Grease
Paste ZZK-3u Al - Hermetol AZ (Poland); UE 130 Ca 5 (Romania)
Agrinol LZ-162у Li-Zn 4 / 5 Cluber Lubrication Staburags NBU 32
Agrinol Armatol-238 Si+C 0 / 1 Cluber Lubrication Staburags NBU 12C
Correspondence table productsREFERENCE BOOK
160
MET
AL P
ACKI
NG
Cor
resp
onde
nce
tabl
e pr
oduc
ts
NAME TYPE NLGI ANALOGS
Agrinol Rez’bol ОМ-2 Si 0
Jet-Lube® APY Modifi ed; ESSO POWR Kote / Grease AS;SHELL High Pressure Modifi ed Thread Compound, Malleus TC;Bakerseal.Prod. N899-20
Reducer lubricants (semifl uid)
Transol A Li 00
SHELL Alvania EP 00 / LIQVI MOLY Fliessfett ZS 00; Q8 Rubens 00CASTROL CLS Grease 00; NESTE Center Grease 00 EP;76 Unoba EP Grease 00; TEXACO Multifak 6833 EP 00
CIATIM -208 Са 1 SHELL Alvania GL / LF; MOBILlux EP 023; TOTAL Multis EP 0
Break-in paste
VNII NP-232 Li+Mo 3 SHELL Aviation Grease S.54768; EXXON Aviation Anti-Seize;DG Molycot 17; CASTROL Compounl 1 / Impervia AS
Agrinol Limol А Li+Mo 1
VNII NP-225 Si+Mo 00
REFERENCE BOOK
161
Ann
ex
Annex
OİLS AND LCTP
Index name Volume in dm3
Railway tanks
Tankers
Barrels 216,5
Barrels 100
Barrels 60
Barrels 50
Canisters of different volume 0,5-20
GREASES
Barrels 213
Barrels 60
Metal drums 20
Plastic pails 10
Plastic pails 5
Cans 1
Cans 0,5
Cartridges 0,31
Eurocartridges 0,4
Tubes 0,25
In agreement with the customer the lubrication may be shipped in other types of packing designed to transport plastic products.
REFERENCE BOOK
162
Inde
x
Index
5W-30 SL/CF ........................................................ 95W-30 SM/CF ...................................................... 95W-40 SN / CF ...................................................... 910W-30 SM/CF ..................................................1110W-40 CI-4 ......................................................1110W-40 CI-4/SL ................................................11132-08 .................................................................76Aerol-1A ........................................................... 113Aerol-A .............................................................. 113Agrinol 1-13.......................................................91Agrinol 5W-40 CG-4/SJ ..................................10Agrinol 5W-40 SL/CF ......................................10Agrinol 10W-40 CF-4/SH ..............................13Agrinol 10W-40 CG-4/SJ ................................10Agrinol 10W-40 SG/CD ..................................13Agrinol 10W-40 SL/CF ...................................10Agrinol 15W-30 SF/CE ...................................14Agrinol 15W-40 CF-4/SG ...............................13Agrinol 15W-40 CG-4/SJ ................................12Agrinol 15W-40 CG-4/SL ...............................12Agrinol 15W-40 CH-4/SJ ...............................12Agrinol 15W-40 CI-4 .......................................12Agrinol 15W-40 SF/CC ...................................13Agrinol 15W-40 SG/CD ..................................13Agrinol 20W-40 SF/CC ...................................14Agrinol 20W-50 SF/CC ...................................14Agrinol A .............................................................40Agrinol Akvol-2 .............................................. 140Agrinol Akvol-2E ........................................... 140Agrinol Aqua Moto 2T ....................................21Agrinol Armatol-238 .....................................127Agrinol ATF ІІD..................................................37Agrinol ATF ІІI ...................................................37Agrinol AU ..........................................................41Agrinol BM-1 .....................................................71Agrinol BM-3 .....................................................71Agrinol BM-4 .....................................................71Agrinol BM-5 .....................................................72
Agrinol BM-6 .....................................................72Agrinol BM-11 ...................................................72Agrinol Buksol................................................ 108Agrinol Dolotol N .......................................... 118Agrinol Dolotol АU ....................................... 118Agrinol EHP ..................................................... 138Agrinol EKS-5 ................................................. 142Agrinol EТ-2U ................................................ 139Agrinol GK ..........................................................50Agrinol Grafi tol .............................................. 114Agrinol Gun Lodge RG ....................................74Agrinol Gun Lodge VO ....................................74Agrinol Hidrofobinol-I ................................. 130Agrinol HP ....................................................... 138Agrinol İ100PV ..................................................59Agrinol İ100PVs ................................................59Agrinol İNSp-20 ................................................61Agrinol İNSp-40 ................................................61Agrinol İNSp-65 ................................................61Agrinol İNSp-110 .............................................61Agrinol İP-1l ................................................... 101Agrinol İP-1z ................................................... 101Agrinol KM-22...................................................51Agrinol Kranol ................................................ 126Agrinol KS-19p .................................................46Agrinol LimolA ............................................... 129Agrinol LZ-162u .............................................127Agrinol Marine TBN 15 ..................................23Agrinol Marine TBN 15 ..................................23Agrinol MGD-14m ............................................48Agrinol Moto Drive 2T ....................................22Agrinol Moto Drive 4T ....................................22Agrinol Moto Racer 2T ...................................21Agrinol MP ..........................................................73Agrinol MP Plus ................................................73Agrinol MPT-2m ...............................................73Agrinol MS-8p ...................................................43Agrinol MS-20 ...................................................64
IndexREFERENCE BOOK
163
Inde
x
Agrinol MS-20p ................................................64Agrinol MS-20ps ..............................................64Agrinol MULTIPLEX GL-5 SAE-90 ...............31Agrinol MULTIPLEX SAE 140 GL-5 .............31Agrinol MZ-8 ......................................................67Agrinol MZ-16 ...................................................67Agrinol MZ-38 ...................................................67Agrinol MZ-90 ...................................................67Agrinol MZ-120 .................................................67Agrinol MZM-16 ...............................................68Agrinol MZM-26 ...............................................68Agrinol MZM-120 .............................................68Agrinol MZT .....................................................107Agrinol Nigrol-L ................................................36Agrinol No158 ...................................................86Agrinol No158M ...............................................86Agrinol OM ...................................................... 139Agrinol PJT-46 ...................................................62Agrinol PJT-220 ................................................62Agrinol PJT-460 ................................................62Agrinol PJT-460U .............................................62Agrinol Polynol .................................................95Agrinol Polynol ЕР1 ........................................95Agrinol Polynol ЕР2 ........................................95Agrinol ProkatOl ЕР 2 .................................. 102Agrinol PS-20 ....................................................60Agrinol PS-28z ..................................................60Agrinol Puma-Мl ........................................... 110Agrinol Puma-Мz .......................................... 110Agrinol R .............................................................40Agrinol Refoil 10KS .........................................47Agrinol Relsol GS .......................................... 110Agrinol Relsol M ............................................ 110Agrinol Rezbol OM-2 ....................................127Agrinol RG ....................................................... 142Agrinol Rope 39U.......................................... 121Agrinol SAE 10W CF-4 ...................................15Agrinol SAE 30 CF-4 .......................................15
Agrinol SAE 40 CF-4 .......................................15Agrinol SAE 50 CF-4 .......................................15Agrinol ShRB-4 .................................................86Agrinol Solidol ..................................................81Agrinol TEMP-3KN ........................................137Agrinol Termol ..................................................69Agrinol Termol-1 ........................................... 111Agrinol Termol-2 ........................................... 111Agrinol Torsiol-35B/1 .................................. 122Agrinol Torsiol-35B/2 .................................. 122Agrinol Torsiol-35E....................................... 122Agrinol Tosol-30 .............................................147Agrinol Tosol-40 .............................................147Agrinol Tosol-65 .............................................147Agrinol Tosol A-40 ........................................ 148Agrinol Tosol TA ............................................. 148Agrinol TSp-10 ..................................................35Agrinol TSp-14gip ...........................................35Agrinol TSp-15K ...............................................35Agrinol Uniol-2M-1 ...................................... 102Agrinol Uniol-2M-2 ...................................... 102Agrinol VMGZ ....................................................41Agrinol VNİİ NP -210 ................................... 115Agrinol VNİİ NP -219 ................................... 115Agrinol ZES ..................................................... 125Agrinol ZhRO .................................................. 108Agrinol ZhT-72 ............................................... 109Agrinol ZhT-79L ............................................. 109Agrinol ZhTКZ-65 ......................................... 109Agrinol КEТ-1 ................................................. 135Agrinol КEТ-1M ............................................. 135Agrinol М-14B ...................................................29Agrinol М-14D2 .................................................28Agrinol М-14D2U ..............................................28Agrinol М-14G2k ...............................................18Agrinol МS-20gk ..............................................64Agrinol МТ-16P .................................................29Agrinol ТSzp-8 ..................................................34
IndexREFERENCE BOOK
164
Inde
x
Agrinol ТАD-17i ................................................34Agrinol ТАp-15В ...............................................34Agrniol Termostan ........................................ 100AMG-10 ...............................................................41AMS-1 ............................................................... 124AMS-3 ............................................................... 124Anticor-270 ........................................................74Arginol Nigrol-Z ...............................................36BENTOL-1 M ......................................................96Cannon Lubricant ......................................... 125Chain Saw Oil EXPERT ...................................24Chain Saw Oil Standard .................................25CİATİM-201 ..................................................... 123CİATİM-202 ..................................................... 119CİATİM-203 ..................................................... 119CIATIM-205 ..................................................... 116CİATİM-208 ..................................................... 128CIATIM-221 ..................................................... 114Classic SAE 80W-90 API GL-4 ......................30Cold Roller ........................................................137Crystal ............................................................... 149Cylinder oil 38...................................................63Cylinder oil 52...................................................63Form Divider ......................................................75Form Divider M .................................................75Gold SAE 80W-90 API GL-5 ..........................30Graphite grease ................................................82Grease Agrinol Fiol -2U ..................................85Grease Agrinol ShRUS -4 ...............................85Green Rubber Grease ......................................83HA-30 ...................................................................47HDS 460 ..............................................................95HF 12-16 .............................................................47HF 22-24 .............................................................47Highrate XP ........................................................57Hydraulic Lift .....................................................55Hydroil HM .........................................................53Hydroil HM Ultra ..............................................56
İ-5A .......................................................................65İ-8A .......................................................................65İ-12A .....................................................................65İ-12A1 ...................................................................65I-20А .....................................................................66I-30А .....................................................................66I-40А .....................................................................66I-50А .....................................................................66K-12 ......................................................................46K-19 ......................................................................46KAS-1SM .......................................................... 139Kompressoil .......................................................44Konstalin-1 grease ..........................................91Konstalin-2 grease ..........................................91KS-19 ...................................................................46Ligrease 00 ........................................................87Ligrease 0 ...........................................................87Ligrease 1 ...........................................................87Ligrease 2 ...........................................................88Ligrease 3 ...........................................................88Ligrease ЕР 00 ..................................................89Ligrease ЕР 0 .....................................................89Ligrease ЕР 1 .....................................................89Ligrease ЕР 2 .....................................................90Ligrease ЕР 3 .....................................................90low SAPS .............................................................11LubriLiCa .......................................................... 103LZ-CNİİ ...............................................................107M-8V .....................................................................20Molyroll EP1 ......................................................84Molyroll EP2 ......................................................84Molyroll EP3 ......................................................84MOLYROLL GR1 ............................................. 112MOLYROLL GR1 ............................................. 112MR-7 .................................................................. 135MR-7B ............................................................... 135MVP .......................................................................76OKB 122-7 ....................................................... 123
IndexREFERENCE BOOK
165
Inde
x
PELLETON EP ....................................................93PELLETON EP ....................................................93PELLETON SKS .................................................94PELLETON SKS .................................................94Plating GR ....................................................... 105Platinum SAE 75W-90 API GL-5..................30PROTECTING TG ............................................ 120PS-28 ....................................................................60Red Calcium Grease ........................................83RG-1s ................................................................. 141RG-2s ................................................................. 141Rolling GR S .................................................... 106Rolling GR SW ................................................ 106Rolling GR W ................................................... 106SAE 85W-140 API GL-5 ..................................30SGT ........................................................................42Silver SAE 85W-90 API GL-5 ........................30SKS 300 m-1* ....................................................92SKS-300 m-1 .....................................................92SKS 300 m-2* ....................................................92SKS-300 m-2 .....................................................92Sliding EP 2 SHC 220 .....................................99Sliding GR 00 ....................................................97Sliding GR 0 .......................................................97Sliding GR 1 .......................................................98Sliding GR 2 .......................................................98SP-3 ................................................................... 138Special Oil ART .................................................58Special Oil HMT ................................................40STOU SAE 10W-30 ...........................................38STOU SAE 10W-40 ...........................................38TK ..........................................................................49TL Effort ........................................................... 136Transol-100A .................................................. 128Transol-200A .................................................. 128TSO .......................................................................50TSp-10 .................................................................33TSp-14gip ...........................................................33
TSp-15K ..............................................................33UTTO 80W ..........................................................39UTTO 85W ..........................................................39VNİİ NP -207 ................................................... 115VNİİ NP-225 .................................................... 129VNİİ NP-232 .................................................... 129VNİİ NP-263 .................................................... 126VNİİ NP -279 ................................................... 116VNİİ NP -282 A ................................................117VNİİ NP -282M A ............................................117ZZK-3u .............................................................. 126АМТ-300 ..............................................................70К-17 .....................................................................74М-6z/12G1 ..........................................................20М-8DМ .................................................................19М-8G2 ...................................................................16М-8G2k .................................................................16М-10DМ ..............................................................19М-10G2 .................................................................17М-10G2k ...............................................................17М-10V2 .................................................................18М-14DTsL20 .......................................................26М-14DTsL30 .......................................................26М-14V2 .................................................................23М-16G2TsS .........................................................23М-20G2 .................................................................29М-20V2F...............................................................27М-20Е70 .............................................................27Т-1500 .................................................................49Тp-22 ....................................................................42Тp-30 ....................................................................42Тp-46 ....................................................................42ТАD-17i ...............................................................32ТАp-15В...............................................................32