Post on 11-Jun-2020
transcript
Page 1 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
Project:
Type: Qty:
Date: Customer:
M130LED Direct
Order Code: - - - - - - - - - -
Emergency Options
EC12,13 Emergency Circuit Wiring
DL
Damp Location Rated
FS In-line Fuse
SS Separate Switching
12 See page 8 for full details and restrictions13 For emergency options with sensors, please
consult factory.14 EM available in 4’ and ≥6’. Please consult
factory.
Fixture Options
Nominal Fixture Length
01* 1 ft.
02 2 ft.
03 3 ft.
04 4 ft.
05 5 ft.
06 6 ft.
07 7 ft.
08 8 ft.
09 9 ft.
10 10 ft.
11 11 ft.
12 12 ft.
XX Runs (over 12’) and Configurations, round up to the nearest foot and replace the “xx” with the # (i.e. 13=13 nominal)
* Custom colors are available, please consult factory
Individual fixtures, Runs and Configurations are supplied in nominal lengths to ensure full, even, illumination. See pages 2 through 6 for additional details.
-
MI Clear Lens with Microprism
*1’ fixture only available with 1B35 or 2B35 light engines
Sensor Options
xE10,11 Enlighted
Replace “X” with quantity
xS110,11 Sensor Switch Daylight
xS210,11 Sensor Switch Occ/Vac
xS310,11 Sensor Switch Occ/Vac/Daylight
LED WARRANTY
5YEAR ARRA
CompliantADA
Compliant
-
10 Minimum length 2’. See page 9 for full
details and restrictions.11 Requires DIM driver (0-10V)
xSN nLight enabled (consult factory)
EMR Remote Micro Inverter (consult factory)
EM12,13,14 Integral EM Battery Pack
BL* Semi-Matte Black
xV Lutron Vive (consult factory)
Series L13 M130 LED Direct
Light Engine
Shielding
C Cable
RS Rigid Stem
S Swivel Stem
W3 Wall Mount
F4 Surface Mount (w/Flex Whip)
Mounting
LW LED Optimized White Lens
Finish
Voltage
L13
L13
WH* White
SP* Specify Premium Color
SV* Silver
CCT 27 2700K90+ CRI
30 3000K90+ CRI
40 4000K 90+ CRI
35 3500K 90+ CRI
120120 Volt
277277 Volt
UNV120 through 277V 50/60Hz capable
3 Consult factory for lengths under 2’ 4 Over 8’ supplied with 2 more housings that are joined in the field
IT90 Lit “T” section
IX90 Lit “X” section
IL90 Lit Horizontal 90° Corner
Configuration Options
1 Values calculated from a 4’ fixture at 4000K with LW shielding and a DIM driver. For additional information please see page 2.
2 Available starting at 2’ and up
1B351 595lm/8.6W per foot
2B351 1080lm/17.1W per foot
1B301,2 508lm/7.2W per foot
2B301,2 923lm/14.3W per foot
1B251,2 456lm/6.4W per foot
2B251,2 827lm/12.7W per foot
1B201,2 344lm/4.7W per foot
2B201,2 624lm/9.4W per foot
1B451,2
748lm/11.0W per foot
1B401,2
676lm/9.8W per foot
2B451,2 1358lm/22.0W per foot
2B401,2 1228lm/19.5W per foot
347347 Volt (consult factory)
Driver DMD5,6,9 eldoLED DALI (Logarithmic)
DE15,6,7 Lutron EcoSystem
DC25,6,7,8 Lutron 2-Wire
5 See page 7 for details 6 Not available for 1’ length 7 120V only 8 Not available with 2B40 or 2B459 EM option not available in 4’ length
DIM5 0-10V (Linear)
DML5,6,9 eldoLED SOLOdrive 0-10V (Logarithmic)
DM5,6,9 eldoLED SOLOdrive 0-10V (Linear)
DC5 Lutron 5-Series (consult factory)
Page 2 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M130LED Direct
Construction:
Housing - Continuous, low copper 6063-T6 extruded aluminum profile with aluminum endcaps, available as Individual fixtures (up to 12’) or Runs.
Geartray - Low copper 6063-T6 extruded aluminum profile.
Shielding - Extruded, impact resistant acrylic lens:- LED Optimized White Lens (LW)- Clear Lens with Microprism (MI)
Mounting(s) - 1/16” Aircraft Cable, ø5/8” Swivel or Rigid Steel Stem, Wall Bracket, Surface mounting (see pages 3 through 6 for details).** Cable, Stem and Wall mountings may not be symmetrical for Runs and Configurations due to the use of modular housing lengths. If symmetrical suspensions are required please consult the factory.
Standard Luminaire lengths - All standard luminaires are supplied in nominal lengths to ensure full, even, illumination. Runs and Configurations are available in approximately 1/4” increments starting at the nominal 12’ fixture length.** Individual luminaires are not joinable in the field.
Exact length luminaires - Individual luminaires, Runs, and Configuration are available in exact lengths to meet your project needs. Please consult factory with your requirements. ** Lens luminance may soften at the very ends of the straight sections for exact length luminaires.
L13 Joiner(s) - Runs and Configurations are supplied in multiple housings that are joined together in the field using the supplied L13 Joiner System. This allows ease of installation and ensures a uniform appearance (see page 8 for detail).
Weight: 4.5 lb. per foot.
Electrical/Performance:
LED Light Engine - Brand-name mid-power LEDs create a high efficiency LED light engine able to provide a lumen maintenance of 96% at 25,000 hours and 93% at 60,000 hours for 1B light engine and 96% at 25,000 hours and 92% at 60,000 hours for 2B light engine @ 25ºC per TM-21 reports. Reported L70 greater than 60,000 hours.
Delivered Lumens - Due to LED manufacturer’s tolerances the listed output has a ±5% tolerance.
CCT - Available in 2700K, 3000K, 3500K and 4000K, tolerance within a 3-step MacAdam ellipse.
CRI - 90+.
All Drivers - High efficiency, constant current, soft start, Electronic Class 2 with a PFC>0.90. For more detailed information on the available drivers please see page 7.
Sensors - Selux offers a variety of integral sensor options. For details and specifications, please refer to page 9.
Emergency - There are multiple emergency options available - emergency circuit, remote micro inverter, and integral battery pack. All options compliant with UL 924 listed emergency luminaire. Please consult factory for use of sensors with emergency options. For more details on EC and EM options, see page 8.
Thermal Performance:
Ambient Operating Temperature - Luminaires suitable for maximum ambient temperature of 35°C (95°F) for all drivers.
Luminaires are suitable for minimum ambient temperatures of:-40ºC (-40ºF) for DIM, DM, DML, and DMD drivers.0ºC (32ºF) for DC2 and DE1 drivers.
Luminaire Finish:
Powder Coat - All Selux luminaries are finished in high quality polyester powder coating in our Tiger Drylac certified facility and are tested in accordance with test specifications for coatings from ASTM and PCI.
All products undergo a five stage intensive pretreatment process where product is thoroughly cleaned, phosphated, and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultra violet resistance for color retention.
Standard interior colors are White (WH), Semi-Matte Black (BL), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide. LM-79 testing is performed using white finish. Other finishes may impact light output.
Warranty:
5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the MLED series LED luminaire shall be free from defects in material and workmanship for up to five (5) years from date of shipment. This limited warranty covers the LED driver and LED light engine when installed according to Selux instructions and operated within the Ambient Temperature. For additional details and exclusions, see “Selux Terms and Condition of Sale.”
Certifications and Compliance: NRTL - For Dry and Damp location (I.E. cULus; cCSAus)ARRA CompliantRoHS Compliant
5” (127mm)
4 3/4” (121mm)
5 1/4” (133mm)
5 1/4” (133mm)
5” (127mm)
4 3/4” (121mm)
1Bxx Light Engine 2Bxx Light Engine
LW lens shown for reference
Page 3 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M130LED Direct
1
"A"
Feed
"B" 48"
"B"
"D" Feed
BottomView
SideView
"C"
Cable Mounting (C)
Outlet box for feed only (by others)
L13 Cable (C) Suspension Detail (Feed location(s) only)
L13 Cable (C) Suspension Detail (Non-Feed location(s) only)
1. Ø1/16” Aircraft Cable with chrome gripper for easy adjustment (48” max. from ceiling to luminaire)
Cable Mounting (C) - Dimensions
Nominal Length
“A” Housing Length
* “B” (Ref.) End Suspensions
“C” Mid. Suspension
“D” Feed Location
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
01 (1 ft.) 1' - 5/16" 313 0' - 2 1/8" 54 0' - 8 1/8" 206 0' - 1 1/8" 29
02 (2 ft.) 2' - 1/4" 616 0' - 2 1/8" 54 1' - 8" 508 0' - 1 1/8" 29
03 (3 ft.) 3' - 5/16" 923 0' - 3 1/8" 79 2' - 6 1/8" 764 0' - 2 1/8" 54
04 (4 ft.) 3' - 11 7/16" 1205 0' - 3 1/8" 79 3' - 5 3/16" 1047 0' - 2 1/8" 54
05 (5 ft.) 4' - 11 7/16" 1510 0' - 3 1/8" 79 4' - 5 3/16" 1351 0' - 2 1/8" 54
06 (6 ft.) 5' - 11 7/16" 1815 0' - 3 1/8" 79 5' - 5 3/16" 1656 0' - 2 1/8" 54
07 (7 ft.) 6' - 11 7/16" 2119 0' - 3 1/8" 79 6' - 5 3/16" 1961 0' - 2 1/8" 54
08 (8 ft.) 7' - 11 7/16" 2424 0' - 3 1/8" 79 7' - 5 3/16" 2266 0' - 2 1/8" 54
09 (9 ft.) 8' - 11 7/16" 2729 0' - 3 1/8" 79 8' - 5 3/16" 2570 0' - 2 1/8" 54
10 (10 ft.) 9' - 11 7/16" 3034 0' - 3 1/8" 79 9' - 5 3/16" 2875 0' - 2 1/8" 54
11 (11 ft.) 10' - 11 7/16" 3339 0' - 3 1/8" 79 10' - 5 3/16" 3180 0' - 2 1/8" 54
12 (12 ft.) 11' - 11 7/16" 3643 0' - 3 1/8" 79 11' - 5 3/16" 3485 0' - 2 1/8" 54
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.
Cable Mounting (C)
Cross bar with 1/4”-20 rod and ground screw
1/4” x 5” diameter canopy (White)
2x White cable stay
Cord strain relief bushing
Chrome gripper
1/4”-20 Threaded Rod (supplied and installed in the field by others)2x Outlet box screws
(by others)
1/4”-20 Slip ring coupler
Feed cord (White)
1/16” Aircraft cable
Luminaire
1/4”-20 Slip ring coupler
1/16” Aircraft cable
Chrome gripper
Luminaire
1/4” x 2” diameter Canopy (White)
Min. 5/8” toMax. 3/4”Min. 5/8” toMax. 3/4”
Page 4 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
"A"
Feed
"B" 48"
"B"
"D" Feed
BottomView
SideView
"C"
1 2
Stem Mounting (S and RS)
Outlet box (supplied and installed by others)
L13 Swivel Stem (S) Suspension Detail (feed wires through stem supplied by Selux)
L13 Rigid Stem (RS) Suspension Detail (feed wires through stem supplied by Selux)
3/8” IP Cross bar with ground screws
Hemispherical assembly
1 7/16” x 5” diameter canopy (White)
1. ø5/8” Swivel Stem provides 30° swivel and can be cut in field (48” max. from ceiling to luminaire).
2. ø5/8” Rigid Stem is fixed and is not able to be cut/adjusted in field (48” max. from ceiling to luminaire).
Pin
3/8” IP steel stem (White)
Dress nut
Square nut
Luminaire
Outlet box (supplied and installed by others)
3/8” IP nipple (supplied and installed by others)
Suspension hickey
Canopy securing screw
1/4” x 5” diameter canopy (White)
Swivel (S) and Rigid Stem (RS) Mountings - Dimensions
Nominal Length
“A” Housing Length
* “B” (Ref.) End Suspensions
“C” Mid. Suspension
“D” Feed Location
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
01 (1 ft.) 1' - 5/16" 313 0' - 2 1/8" 54 0' - 8 1/8" 206 0' - 2 1/8" 54
02 (2 ft.) 2' - 1/4" 616 0' - 2 1/8" 54 1' - 8" 508 0' - 2 1/8" 54
03 (3 ft.) 3' - 5/16" 923 0' - 3 1/8" 79 2' - 6 1/8" 764 0' - 3 1/8" 79
04 (4 ft.) 3' - 11 7/16" 1205 0' - 3 1/8" 79 3' - 5 3/16" 1047 0' - 3 1/8" 79
05 (5 ft.) 4' - 11 7/16" 1510 0' - 3 1/8" 79 4' - 5 3/16" 1351 0' - 3 1/8" 79
06 (6 ft.) 5' - 11 7/16" 1815 0' - 3 1/8" 79 5' - 5 3/16" 1656 0' - 3 1/8" 79
07 (7 ft.) 6' - 11 7/16" 2119 0' - 3 1/8" 79 6' - 5 3/16" 1961 0' - 3 1/8" 79
08 (8 ft.) 7' - 11 7/16" 2424 0' - 3 1/8" 79 7' - 5 3/16" 2266 0' - 3 1/8" 79
09 (9 ft.) 8' - 11 7/16" 2729 0' - 3 1/8" 79 8' - 5 3/16" 2570 0' - 3 1/8" 79
10 (10 ft.) 9' - 11 7/16" 3034 0' - 3 1/8" 79 9' - 5 3/16" 2875 0' - 3 1/8" 79
11 (11 ft.) 10' - 11 7/16" 3339 0' - 3 1/8" 79 10' - 5 3/16" 3180 0' - 3 1/8" 79
12 (12 ft.) 11' - 11 7/16" 3643 0' - 3 1/8" 79 11' - 5 3/16" 3485 0' - 3 1/8" 79
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.
Stem Mounting (S and RS)
LuminaireDress nut
Square nut
Square nut
Square nut
3/8” IP steel stem (White)
M130LED Direct
Page 5 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M130LED Direct
BottomView
TopView
"C""B" "B"
"A""D" Feed
Wall Mounting (W)
For patterns and configurations that include a wall mounted option, please see page 10 for details.
Aluminum wall bracket (by Selux)
4”x4” or 2”x4” J-Box at feed location (supplied and installed by others).
1/4”-20 Threaded rod, 1/4”-20 lock washer and 1/4”-20 nut required to anchor the wall bracket. Mounting hardware supplied and installed to code by others.
Wall Mount (W) (Covers a 4x4 J-Box only)
(1Bxx light engine shown)
Wall (W) Mount - Dimensions
Nominal Length
“A” Housing Length
* “B” (Ref.) End Suspensions
“C” Mid. Suspension
“D” Feed Location
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
01 (1 ft.) 1' - 5/16" 313 0' - 6 3/16" 157 NA 0' - 6 3/16" 157
02 (2 ft.) 2' - 1/4" 616 0' - 3 1/8" 79 1' - 6 1/16" 458 0' - 3 1/8" 79
03 (3 ft.) 3' - 5/16" 923 0' - 6 1/8" 156 2' - 1/8" 612 0' - 6 1/8" 156
04 (4 ft.) 3' - 11 7/16" 1205 0' - 6 1/8" 156 2' - 11 3/16" 894 0' - 6 1/8" 156
05 (5 ft.) 4' - 11 7/16" 1510 0' - 6 1/8" 156 3' - 11 3/16" 1199 0' - 6 1/8" 156
06 (6 ft.) 5' - 11 7/16" 1815 0' - 6 1/8" 156 4' - 11 3/16" 1504 0' - 6 1/8" 156
07 (7 ft.) 6' - 11 7/16" 2119 0' - 6 1/8" 156 5' - 11 3/16" 1808 0' - 6 1/8" 156
08 (8 ft.) 7' - 11 7/16" 2424 0' - 6 1/8" 156 6' - 11 3/16" 2113 0' - 6 1/8" 156
09 (9 ft.) 8' - 11 7/16" 2729 0' - 6 1/8" 156 7' - 11 3/16" 2418 0' - 6 1/8" 156
10 (10 ft.) 9' - 11 7/16" 3034 0' - 6 1/8" 156 8' - 11 3/16" 2723 0' - 6 1/8" 156
11 (11 ft.) 10' - 11 7/16" 3339 0' - 6 1/8" 156 9' - 11 3/16" 3028 0' - 6 1/8" 156
12 (12 ft.) 11' - 11 7/16" 3643 0' - 6 1/8" 156 10' - 11 3/16" 3332 0' - 6 1/8" 156
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.
123
33
1
4” (102mm)
1” (25mm)
6” (152mm)
4” (102mm)
Page 6 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M130LED Direct
"C"
"B" "B"
"A""D" Feed
BottomView
SideView
"C1"1' thru 5'6' thru 8' "C"
"C"
"B" "B"
"A""D" Feed
BottomView
SideView
"C1"9'
10' thru 12' "C""B1" "B1"
"C2"
Surface Mounting (F) - 1’ to 8’
1. ø5/16” Mounting hole drilled at the factory (mounting hardware to code by others).
1
Surface Mounting (F) - Over 9’ to 12’
Surface Mount (F)
Surface Mount (F) - Dimensions
Nominal Length
“A” Housing Length
* “B” (Ref.) End Suspensions
* “B1” End Suspensions
“C” Mid. Suspension
“C1” Mid. Suspension
“C2” Mid. Suspension
“D” Feed Location
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
01 (1 ft.) 1' - 5/16" 313 0' - 1 5/8" 41 N/A 0' - 9 1/8" 231 N/A N/A 0' - 4 1/8" 105
02 (2 ft.) 2' - 1/4" 616 0' - 1 5/8" 41 N/A 1' - 9" 534 N/A N/A 0' - 4 1/8" 105
03 (3 ft.) 3' - 5/16" 923 0' - 6 1/8" 156 N/A 2' - 1/8" 612 N/A N/A 0' - 2 1/8" 54
04 (4 ft.) 3' - 11 7/16" 1205 0' - 6 1/8" 156 N/A 2' - 11 3/16" 894 N/A N/A 0' - 2 1/8" 54
05 (5 ft.) 4' - 11 7/16" 1510 0' - 6 1/8" 156 N/A 3' - 11 3/16" 1199 N/A N/A 0' - 2 1/8" 54
06 (6 ft.) 5' - 11 7/16" 1815 0' - 6 1/8" 156 N/A 3' 914 1' - 11 3/16" 590 N/A 0' - 2 1/8" 54
07 (7 ft.) 6' - 11 7/16" 2119 0' - 6 1/8" 156 N/A 3' 914 2' - 11 3/16" 894 N/A 0' - 2 1/8" 54
08 (8 ft.) 7' - 11 7/16" 2424 0' - 6 1/8" 156 N/A 3' 914 3' - 11 3/16" 1199 N/A 0' - 2 1/8" 54
09 (9 ft.) 8' - 11 7/16" 2729 0' - 6 1/8" 156 0' - 6" 153 3' - 11 3/16" 1199 NA 3' 914 0' - 2 1/8" 54
10 (10 ft.) 9' - 11 7/16" 3034 0' - 6 1/8" 156 0' - 6" 153 3' 914 1' - 11 3/16" 590 3' 914 0' - 2 1/8" 54
11 (11 ft.) 10' - 11 7/16" 3338 0' - 6 1/8" 156 0' - 6" 153 3' 914 2' - 11 3/16" 894 3' 914 0' - 2 1/8" 54
12 (12 ft.) 11' - 11 7/16" 3643 0' - 6 1/8" 156 0' - 6" 153 3' 914 3' - 11 3/16" 1199 3' 914 0' - 2 1/8" 54
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.
Page 7 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
0-10V linear dimming (DIM)Luminaires supplied with drivers offering the capability of either normal switched operation or 0-10V dimming for linear dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to 1%. (Due to size constraints, 1’ luminaires are supplied with a driver from a different manufacturer than 2’ and above luminaires. For details, please consult factory.)
eldoLED SOLOdrive 0-10V linear dimming (DM)Luminaires supplied with SOLOdrive 0-10V dimming driver for linear dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.
eldoLED SOLOdrive 0-10V logarithmic dimming (DML)Luminaires supplied with SOLOdrive 0-10V dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.
eldoLED SOLOdrive DALI dimming (DMD)Luminaires supplied with SOLOdrive DALI dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.
LUTRON 2-wire dimming (DC2)Luminaires supplied with Hi-lume 2-wire dimming driver (120V only) programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.
LUTRON EcoSystem dimming (DE1)Luminaires supplied with Hi-lume EcoSystem (4 wire, digital link) dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1% SoftOn/FadeToBlack.
* For control recommendations, please contact driver manufacturer.
M130LED Direct
Drivers:
Driver Quantity
Light Engine 1 ft. 2 ft. 3 ft. 4 ft. 5 ft. 6 ft. 7 ft. 8 ft. 9 ft. 10 ft. 11 ft. 12 ft. RUN
1Bxx
DIM 1 1 1 1 2 2 2 2 3 3 3 3 Approximately 1 driver per 4 ft.
DM, DML and DMD drivers N/A 1 1 1 1 1 2 2 2 2 3 3 Approximately 2 drivers per 4 ft.
DC2 and DE1 drivers N/A 1 1 1 2 2 2 2 3 3 3 3 Consult Factory
2Bxx
DIM 2 2 2 2 4 4 4 4 6 6 6 6 Approximately 2 drivers per 4 ft.
DM, DML and DMD drivers N/A 2 2 2 2 2 4 4 4 4 6 6 Approximately 2 drivers per 4 ft.
DC2 and DE1 drivers N/A 2 2 2 4 4 4 4 6 6 6 6 Consult Factory
*For inrush and control current, please refer to driver manufacturers’ spec sheets.
Wiring Diagrams Sensor Wiring Diagrams
- The following wire(s) are in addition to the standard above -
Gray = (-) DALI or 0-10V Dimming ControlPurple = (+) DALI or 0-10V Dimming Control
Violet = “E1” Digital Link Dimming ControlViolet/White = “E2” Digital Link Dimming ControlDE1, DC5
0-10V linear (DIM) 0-10V linear eldoLED SOLOdrive (DM)0-10V logarithmic eldoLED SOLOdrive (DML)DALI eldoLED SOLOdrive (DMD)
DIM, DM, DML & DMD
Lutron EcoSystem (DE1)Lutron 5-Series (DC5)
ENLIGHTED
ELDO 0-10V
SENSORSWITCH
(+)(-) 0-10V AUX (+)
AUX (-)
LED LIGHTENGINE
CONTROL UNITCU-4E-FM
SENSORSU-5E-IL
Live
120
/277
V
Neu
tra
l
blu
ew
hite
whitered
purplegray
Enlighted
DIM DRIVER
Page 8 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M130LED Direct
90° Elbow on top of the housing (⅞" feed hole)
⅜" flexible metal conduit (6' long)
6" leads
Straight fitting
Flex Whip - standard for Surface (F) mount Joiner System - standard for Runs
Fuse (FS) - Fusing, luminaires supplied with a in-line fuse located on the hot wire for each feed. (supplied with an 8A slow burn fuse).
Damp Location (DL) - Luminaires are suitable for use in damp location(s). Examples of such locations include protected areas under canopies, marquees, roofed porches, and similar locations where the fixture(s) are protected from direct contact with rain, snow, or excessive moisture (such as ocean spray). Interior locations include areas subject to moderate degrees of moisture, such as basements and certain barns and cold storage buildings.
*For Damp Location with sensors, please consult factory.
Separate Switching (SS) - Luminaires available with separately switched 4’ (nominal) sections starting at 7’ and up. Luminaire is in-tended to be wired to the same panel/breaker (not intended for Emer-gency use).
- To specify this option, the number of separately switched sections and locations of these sections must be provided at time of order.
* If the project requires different separate switching than outlined above please consult the factory.
*For Separate Switching with sensors, please consult factory.
Fixture extrusion
Recommended 5/32"Allen wrench
Joiner extrusion
Fixture extrusion
Fixture extrusionRecommended 5/32"Allen wrench
Joiner extrusionSplice bar joiner
Recommended 1/16"Allen wrench
Fixture extrusion
L13 joiner detail L13Rx joiner detail
Emergency Circuit (EC) - Luminaires with EC option compliant to UL 924 listed emergency luminaire. EC luminaires are intended to be wired to separate panels/breakers for emergency use.
- For 1’ to 6’ nominal luminaires, the entire fixture is wired for operation on emergency circuit.
- For 7’ and up nominal luminaires, the first 4’ nominal length is wired for operation by a separate EM circuit by default to meet the required “Life Safety Code” (NFPA 101).
*If a different configuration is needed please consult the factory.
*For EC with sensors, please consult factory.
Emergency Battery (EM) - Luminaires with EM option are provided with factory installed emergency battery. In the event of an emergency, EM battery will illuminate a nominal 4’ section at 10W (constant) for 90 minutes (250C). Recharge time of 24 hours. If a different configuration is needed, please consult factory.
The emergency battery pack is located integral to fixture and available in nominal 4’ and ≥ 6’ lengths. Please consult factory for 5’ lengths as fit of EM battery will depend on light engine and quantity of drivers. Emergency option will illuminate the first nominal 4’ section of fixture. For fixtures >12’ or if a different configuration is needed, please consult factory.
* Emergency battery option is UNV for use with 120/277V and is not avail-able for 347V.
* For EM with sensors, please consult factory.
Page 9 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M130LED Direct
Lens
Qty 1 Sensor - Beginning
Qty 3+ Sensor - For spacing between sensors, please consult the sensor manufacturer
Beginning of Run
Fixture Length
Lit Section*
Standard Sensor Placement - for other placement options, please consult factory. For functionality and limitations, please see sensor details above.
Aluminum Sensor Plate -to be painted same as fixture unless specified otherwise
Qty 2 Sensor - Beginning and End (9’ fixtures and longer)
Notes: 1. For spacing between sensors, please consult the sensor manufacturer. 2. Exact sensor placement and coverage will be defined by approved factory drawing. 3. Sections controlled by sensors may not be symmetrical - consult factory for layout.
* Lit section will be the fixture length minus 3” for sensor plate.
Factory Presets - Sensors come from the sensor manufacturer with factory presets for each of the settings in above chart. Please see sensor manufacturers’ spec sheets for details on presets and re-programming.
Commissioning - Commissioning of sensors and installation by others. Contact sensor manufacturer for details and costs associated with commissioning the system prior to specification of sensors.
Enlighted SU-5E-IL (E)Enlighted Micro Sensor SU-5E-IL (Independent Lighting) provided as standard with an Enlighted CU-4E-FM Fixture Mount Control Unit integral to fixture. If SU-5E-CL (Connected Lighting) or SU-5E-IoT (Internet of Things) is desired, please contact factory. Occupancy/vacancy, thermal, daylight sensing plus Tunable White, Room & Zone control, Internet of Things (IoT) data collection and reporting control. For full details, please see SU-5E-(IoT/CL/IL) spec sheet on the Enlighted website. Must be paired with a 0-10V driver with auxiliary (DIM driver selection). Commissioning by Enlighted.
*Please contact Enlighted for complete details prior to specifying.
Sensor Switch MSD EZ (S)Occupancy/vacancy and daylight harvesting. For full functionality and programming options, select settings option 3. If a different settings option is selected, other settings may be unavailable. For full details, please see MSD EZ spec sheets on the Sensor Switch website. Must be paired with DIM driver selection. Manual control of dimming not available with MSD EZ sensor. *Please contact Sensor Switch for complete details prior to specifying.
*Sensor can control up to 30 drivers. Please refer to driver quantity chart on page 7. Multiple sensors may be required for longer lengths.
Occupancy Vacancy Daylight Harvesting Driver Compatibility
Enlighted SU-5E-IL (E) √ √ √ DIM
Sensor Switch MSD EZ (S) √ √ √ DIM
Sensor Ordering Chart
Quantity Sensor Settings*
x Number of Sensors E Enlighted SU-5E-IL
S Sensor Switch MSD EZ
1 Daylight
2 Occupancy/Vacancy
3 Daylight/Occupancy/Vacancy
* Settings not available with Enlighted
5” (127mm)
3” (76mm)
Page 10 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
Listed below are the minimum lengths and details for standard shapes. These standard shapes can be combined with each other and/or the standard luminaire lengths, ensuring full even illumination. If you have any questions, please consult the factory.
The minimum standard lengths for “L” shapes:- IL90 open shapes is 4’ x 4’ nominal (example: leg, 90, leg)- IL90 closed shapes is 6’ x 6’ nominal (example: 90, leg, 90)( Exception is that the IL90s can be joined directly to provide a 4’ x 4’ nominal shape)
*For sensors in configurations, please consult factory.
For patterns and configurations that include a wall-mounted option, please consult factory to identify location, on which side of housing and spacing of brackets required.
The minimum standard lengths for “T” and “X” shapes:- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side- IX90 = 8’ nominal for either direction
Standard Direct shapes/configurations:
Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements. Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.
Project Specific Direct shapes/configurations:
M130LED Direct
Direct (L13) Lit Corner and Section - Dimensions
1B Light Engine 2B Light Engine
IL90 IT90 IX90 IL90 IT90 IX90
Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM
“A” Housing (Outside) 2' - 2 5/8" 675 2' - 2 1/16" 662
“A1” Housing (Inside) 1' - 9 5/8" 548 1' - 9 1/16" 535
“C” Housing 2' - 2 5/8" 675 2' - 2 1/16" 662
* “C1” Ref. 2' - 1/8" 612 1' - 11 9/16" 599
“D” Housing 4' - 3/16" 1224 3' - 11 3/16" 1198
* “D1” Ref. 2' - 1/8" 612 1' - 11 9/16" 599
“E” Housing 4' - 3/16" 1224 3' - 11 3/16" 1198
* “E1” Ref. 2' - 1/8" 612 1' - 11 9/16" 599
*Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.
Page 11 of 11 (Rev. 11/2019)
M130_Direct_[1B]v7.1
In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.
Selux Corporation © 2019, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us
M130LED Direct
Photometry
207
413
620
826
1
2
Maximum Candela = 826.3 Located At Horizontal Angle = 22.5, Vertical Angle = 1# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
LW Optics / 1B35 / 4000K CCT
Catalog #: L13-1B35-40-LW-X-04-XX-UNVReport #: 11686484.01 Delievered Lumens: 2380 Input Watts: 34.3825WEfficacy: 69 CCT: 4000KCRI: 95.7
463
926
1389
1852
12
Maximum Candela = 1852 Located At Horizontal Angle = 90, Vertical Angle = .5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)
MI Optics / 1B35 / 4000K CCT
Catalog #: L13-1B35-40-MI-X-04-XX-UNVReport #: 11686484.05 Delievered Lumens: 3001 Input Watts:34.4336WEfficacy: 87 CCT: 4000KCRI: 95.7
CCT multipliers apply to the photometry, IES files, and per foot values listed on page one (light engine).
Light engine multiplier supplied for per foot values listed on page one (light engine).4000K
3500K3000K2700K 0.931
L130 LED Photometry Multiplier Table
CCT Multiplier1.0000.9720.963