M&P 15-22 Rifle - Smith & Wesson

transcript

Safety & Instruction Manual

M&P® 15-22 Rifle

Read the instructions andwarnings in this manual

CAREFULLY BEFOREusing this firearm.

M&P_1522_Rifle_Manual_08-05-16.qxp_S&W MP15-22 Rifle Manual 8/2/16 8:37 AM Page 1

YOUR SAFETYRESPONSIBILITIES

YOUR SAFETY RESPONSIBILITIES CONTINUED

SAFE STORAGE ANDTRANSPORTATION

SAFE STORAGE AND TRANSPORTATION CONTINUED

AMMUNITION

AMMUNITION CONTINUED

FIGURE 1a

AMMUNITION CONTINUED

MODEL AND FEATURESIDENTIFICATION

FIGURE 2

FIGURE 4a

FIGURE 3

Charging Handle Rear Sight

Forend/Hand Guard

Front Sight

Barrel

Upper Receiver

Magazine

Magazine ReleaseTriggerGuard

Trigger

Bolt Catch

SafetySelector Lever

Lower Receiver Stock Position Lock -(when equipped)

Takedown Pin

Ejection Port

FIGURE 4b

INSPECTING YOUR RIFLE

FIGURE 8

FIGURE 9 FIGURE 10

FIGURE 6

FIGURE 5

FIGURE 7

INSPECTING YOUR RIFLE CONTINUED

PREPARATION FOR FIRING

FIGURE 11

PREPARATION FOR FIRING CONTINUED

LOADING

FIGURE 13

LOADINGASSIST

BUTTON - Onthose modelsso-equipped

FIG. 14a

Hold LoadingAssist ButtonDown - Onthose modelsso-equipped

FIGURE 12

Hold followerdown with toolon those modelswith no loadassist button

FIG. 14b

LOADING CONTINUED

FIGURE 17

FIGURE 18a

FIGURE 15

FIGURE 16

FIGURE 18b

LOADING CONTINUED

FIRING

FIGURE 19

FIRING CONTINUED

CLEARING MISFIRES

FIGURE 20

FIGURE 21

FIGURE 22

CLEARING MISFIRES CONTINUED

FIGURE 27

FIGURE 26

FIGURE 25

FIGURE 23

FIGURE 24

CLEARING MISFIRES CONTINUED

UNLOADING

FIGURE 28

FIGURE 32

FIGURE 29 FIG. 30

FIGURE 31

FIGURE 33

DISASSEMBLY /FIELD STRIPPING

FIGURE 36

FIGURE 37

FIGURE 35

FIGURE 34

DISASSEMBLY / FIELD STRIPPING CONTINUED

ASSEMBLY /FIELD STRIPPING

FIGURE 39

FIGURE 40

BOLT ASSEMBLY

CHARGING HANDLE

FIGURE 38

FIG. 41CHARGING HANDLE

ONTO BOLT

ASSEMBLY - FIELD STRIPPING CONTINUED

SIGHT REMOVAL

COLLAPSIBLE STOCK - WHEN EQUIPPED

FIGURE 45

FIGURE 44b

FIGURE 43

FIGURE 42

BOLT INTO UPPERRECEIVER WITH

CHARGING HANDLE IN PLACE

FIGURE 44a

REARSIGHT

FRONTSIGHT

COLLAPSIBLE STOCK - WHEN EQUIPPED CONTINUED

SIGHT ADJUSTMENT

FIG. 48

FIG. 51 FIG. 52

FIG. 49

FIG. 46

FIG. 47

FIG. 50

MAGAZINE

Spring

FloorplateCatch

Floorplate

Follower

FIGURE 53

Load ingAssist

Button

FIG. 54

FIG. 55

FIG. 56

MAGAZINE CONTINUED

FIG. 57

FIG. 58

FIG. 59

FIG. 60

FIG. 61

CLEANING AND MAINTENANCE

CLEANING AND MAINTENANCE CONTINUED

LIMITED WARRANTY

LIMITED WARRANTY CONTINUED

CONTACT AND SHIPPINGINFORMATION

CONTACT AND SHIPPING CONTINUED

PATENT INFORMATION

ADDENDUM:M-LOK™ ACCESSORY RAILS

WSSCRE

S-NUTTT-NUT

FIGURE 3

FIGURE 1Look for the M-LOK™ logothat designates genuine

M-LOK™ system components

FIGURE 2

The M&P15-22 has M-LOK™ slots at 3:00,6:00 and 9:00 posi-tions. The other slotsare cosmetic and for cooling only.

M-LOK™ ACCESSORY RAILS CONTINUED

TOO MUCH GAP

TOO LITTLE GAP

PROPER GAP

CROSS-SECTION OF HAND-GUARD

T-NUTS ARE TOO LOOSE

T-NUTS ARE TOO TIGHT

T-NUTS ARE ADJUSTED TO PROPER GAP

CROSS-SECTION OF HAND-GUARD

PRIOR TO INSTALLATION

FIGURE 4

T-NUT POSITION TOINSTALL/UNINSTALL

SLOT IN HAND GUARD

T-NUT ROTATES WHENYOU TIGHTEN IT

T-NUT IN LOCKEDPOSITION

SCREW IS TIGHT

FIGURE 5

MAKE CERTAIN THAT YOURACCESSORY IS FULLY SEATED IN THE SLOTS AND TIGHTENED SECURELY.

FIGURE 6

1/8˝ Hex Wrench

Handguard Cutawayto show T-Nuts Engaged

FIGURE 7

1/8˝ Hex Wrench

7mm Wrench

FIGURE 8

Short Arm

Hex Wrench

LongArm

FIGURE 9

BATTERY WARNINGS

M&P 15-22 Rifle - Smith & Wesson

Documents