Post on 10-May-2018
transcript
Business Requirements for
Measure
Calorific Value
Status: approved
Version: 1
Revision: -
Date: September, 2015
ebIX® Business Requirements for Measure Calorific Value 2
ebIX® September, 2015
C O N T E N T
A. About this document ....................................................................................................................... 4
A.1. Comments to the ebIX® model .................................................................................................... 4
A.2. References ................................................................................................................................... 4
A.2.1. Standards ................................................................................................................................. 4
A.2.2. ebIX® Documents ..................................................................................................................... 4
A.3. Participants in the project ........................................................................................................... 5
A.4. Main changes since last version .................................................................................................. 5
1. Introduction ..................................................................................................................................... 6
2. Business Requirements View: Measure Calorific Value .................................................................. 8
2.1. Recalculate Calorific Value (Business Process UseCase) ......................................................... 8
2.1.1. Description .......................................................................................................................... 8
2.1.2. Business Process .................................................................................................................. 9
2.1.3. Exchange Established Calorific Value (Business Process UseCase) ................................... 10
2.1.3.1. Description .................................................................................................................... 10
2.1.3.2. Business Process ............................................................................................................ 11
2.1.4. Request Established Calorific Value per MP (Business Process UseCase) ........................ 12
2.1.4.1. Description .................................................................................................................... 12
2.1.4.2. Business Process ............................................................................................................ 13
2.2. Business Partner View ........................................................................................................... 14
2.2.1. Business Partners Recalculate Calorific Value ................................................................... 14
2.3. Business Entity View .............................................................................................................. 15
2.3.1. Established Calorific Value (Class Diagram) ...................................................................... 15
2.3.1.1. Established Calorific Value (State Diagram) .................................................................. 17
2.3.2. Request Established Calorific Value Per MP (Class Diagram) ............................................ 18
2.3.2.1. Request (State Diagram) ............................................................................................... 19
2.3.3. Established Calorific Value Per MP (Class Diagram) .......................................................... 20
ebIX® Business Requirements for Measure Calorific Value 3
ebIX® September, 2015
2.3.3.1. Established Calorific Value Per MP (State Diagram) ..................................................... 21
2.3.4. Negative Response to Request Established Calorific Value per MP (Class Diagram) ....... 22
2.3.4.1. Negative Response to Request Established Calorific Value per MP (State Diagram) ... 23
ebIX® Business Requirements for Measure Calorific Value 4
ebIX® September, 2015
A. About this document This document contains ebIX® Business Requirements for the processes regarding the exchange of
calorific value for gas.
As a general introduction ebIX® has published a separate document “Introduction to ebIX® Business
Requirements and Business Information Models” (see [4]). The introduction also includes the generic
model elements that are not specific for a particular business process.
In line with UN/CEFACT Modeling Methodology version 2 (UMM-2) ebIX® defines the business
requirements before starting the actual modeling. Given the input from the ebIX® gas work group,
the requirements have been specified by the ebIX® work group “Exchange Metered Data” and are
the basis for the Business Information Model which is published in a separate document.
The Business Information Model is in turn the basis for the creation of XML schema’s and is expected
to be the basis for the specification of web services in a next version of the model document. Since
ebIX® supports both Edifact and XML the model will also serve as the basis for the creation of
Message Implementation Guides for the mapping to Edifact UNSM’s. The Business Information
Model and the syntax specific structures are specified by the ebIX® “Technical Committee” (ETC).
A.1. Comments to the ebIX® model If you have comments or suggestions to the model please contact any member of the project group
or directly to Kees Sparreboom, kees.sparreboom@capgemini.com .
A.2. References
A.2.1. Standards [1] UML Profile for UN/CEFACT’s Modelling Methodology (UMM), Base Module, 2.0.
(http://www.unece.org/cefact/umm/umm_index.html) [2] UML Profile for UN/CEFACT’s Modelling Methodology (UMM), Foundation Module, 2.0.
(http://www.unece.org/cefact/umm/umm_index.html)
[3] The Harmonized Role Model (for the Electricity Market) by ebIX®, ENTSO-E, and EFET (www.ebix.org)
A.2.2. ebIX® Documents [4] Introduction to ebIX® Business Requirements and Business Information Models
(www.ebix.org)
[5] Recommended Identification Schemes for the European Energy Market (www.ebix.org)
[6] ebIX® code lists (www.ebix.org )
ebIX® Business Requirements for Measure Calorific Value 5
ebIX® September, 2015
A.3. Participants in the project These Business Requirements as part of the ebIX® Model for the European Energy Market (see [4])
are made in a project with the members of EMD. For a list of members of the ebIX® gas work group
and of ebIX® EMD see www.ebix.org .
A.4. Main changes since last version Old New Clarification Date
Start of updates for Version 1r0-
1. Since this is the first
version of the document
that is to published, there
is no specification of
changes.
End of updates for Version 1r0-
ebIX® Business Requirements for Measure Calorific Value 6
ebIX® September, 2015
1. Introduction Calorific Value is established by means of a gas chromatograph at a Reception Station (which is a
physical installation) and the value is exchanged per Aggregated Reception Station (which is an
administrative entity consisting of one or more Reception Stations).
Below an overview of the relevant options in topology with regard to (Aggregated) Reception
Stations is presented.
RS
DistributionGrid custo
mer
Transmission Grid
meter
Aggregated ReceptionStation
6-11-2014 ebIX
meter
meter
CaloricValue area
MP
MP
MP
MP may
containseveral
To other grid(s)
RSReception
Station
ebIX® Business Requirements for Measure Calorific Value 7
ebIX® September, 2015
This picture is a simplified representation of the most essential elements regarding calorific value.
Actual implementations will vary, but also can be described along the lines represented above.
In the information exchange the calorific value is established either per Aggregated Reception Station
or per Calorific Value Area. Which entity is used is to be decided on the basis of national rules.
ebIX® Business Requirements for Measure Calorific Value 8
ebIX® September, 2015
2. Business Requirements View: Measure Calorific Value
2.1. Recalculate Calorific Value (Business Process UseCase)
Figure 1. Recalculate Calorific Value
2.1.1. Description UseCase description: Recalculate Calorific Value
definition Providing established calorific value by a Calorific Value Calculator (which
often is the TSO or DSO) to a Supplier or DSO (in its capacity of Calorific
Value Calculator) in the gas sector. The Calorific Value is established in a
series of (re-)calculations.
beginsWhen The Calorific Value Calculator decides to or when requested.
preCondition Input data for calorific value from the TSO are made available to the
Calorific Value Calculator for (re-)calculation. The procedure for
(re-)calculation follows national rules.
Partners responsible for the execution of the processes should have access
ebIX® Business Requirements for Measure Calorific Value 9
ebIX® September, 2015
to relevant master data.
endsWhen The established calorific value has been made available to the Energy
Supplier or DSO.
postCondition Supplier or DSO has received the established calorific value.
Exceptions None
actions See 2.1.2
2.1.2. Business Process
Figure 2 BP Recalculate Calorific Value
ebIX® Business Requirements for Measure Calorific Value 10
ebIX® September, 2015
2.1.3. Exchange Established Calorific Value (Business Process UseCase)
Figure 11 Exchange Established Calorific Value
2.1.3.1. Description UseCase description: Exchange Established Calorific Value
definition The Calorific Value Calculator sends Established Calorific Value to the
Supplier and/or to the DSO.
beginsWhen The Calorific Value Calculator
decides to, or
when the (national) time schedule prescribes him to
when requested by the other party.
preCondition The Calorific Value Calculator has available:
Established Calorific Value
master data for the exchange of data
endsWhen The reception of the Established Calorific Value has been acknowledged by
the Supplier or the DSO.
postCondition Established Calorific Value is available for the Supplier or the DSO.
exceptions none
actions See 2.1.3.2
ebIX® Business Requirements for Measure Calorific Value 11
ebIX® September, 2015
2.1.3.2. Business Process
Figure 12 BP Exchange Established Calorific Value
ebIX® Business Requirements for Measure Calorific Value 12
ebIX® September, 2015
2.1.4. Request Established Calorific Value per MP (Business Process
UseCase)
Figure 13 Request Established Calorific Value per MP
2.1.4.1. Description UseCase description: Request Established Calorific Value per MP
definition Supplier requests Established Calorific Value per MP from the Calorific Value
Calculator.
beginsWhen Supplier decides to.
preCondition Relation between Supplier and Calorific Value Calculator.
endsWhen The reception of the Established Calorific Value per MP or of the Negative
Response has been acknowledged by the Supplier.
postCondition Established Calorific Value per MP or the Negative Response are available
for the Supplier.
exceptions none
actions See 2.1.4.2
ebIX® Business Requirements for Measure Calorific Value 13
ebIX® September, 2015
2.1.4.2. Business Process
Figure 14 BP Request Established Calorific Value per MP
ebIX® Business Requirements for Measure Calorific Value 14
ebIX® September, 2015
2.2. Business Partner View
2.2.1. Business Partners Recalculate Calorific Value
Figure 15 Business Partners Recalculate Calorific Value
ebIX® Business Requirements for Measure Calorific Value 15
ebIX® September, 2015
2.3. Business Entity View In the business entity view the principles as described in the Introduction to ebIX® Business Requirements and Business Information Models (www.ebix.org)
[4] are used. See paragraph 1.2.1.1.3 of that document.
(enumerations used for gas only are colored blue, enumerations used for electricity only are colored a kind of purple and enumerations used for both
electricity and gas have the standard color for elements in the diagram (a kind of pink/white)).
2.3.1. Established Calorific Value (Class Diagram)
Figure 16 Established Calorific Value
ebIX® Business Requirements for Measure Calorific Value 16
ebIX® September, 2015
Element definitions, Established Calorific Value
«Business entity»
Established Calorific Value
The information set containing a calorific value, sent by a
Calorific value calculator to a Supplier to facilitate the
financial settlements with either the wholesale supplier of
gas or with the end customer.
The information set may be sent directly or through another
Calorific value responsible.
Observation Period A specific period of time describing the validity of this
established calorific value.
Measure Unit The unit of measure used for the quantity in these measured
data.
Established Calorific
Value
The Established value for this observation
«Business entity»
Aggregated Reception Station
An administrative entity that represents one or more of
reception stations (which are physical installations). This
entity functions as the exchange point between grids where
calorific value and volumes are established.
Aggregated Reception Station is dependent: either
Aggregated Reception Station or Calorific Value Area is to be
used.
Identifier The unique identification of the Aggregated Reception
Station at which the calorific value is established.
«Business entity»
Calorific Value Area
A set of Metering Points for which the same calorific value is
established.
Calorific Value Area is dependent: either Aggregated
Reception Station or Calorific Value Area is to be used.
Identifier The unique identification of the Calorific Value Area for
which the calorific value is established.
Established Calorific Value
Additions
Additional information, related to Established Calorific Value
the use of which may be agreed on a national level. This is
however not used when specifying the payload in the ebIX®
model.
Identifier The unique identification of this set of information as given
by the Calorific Value Calculator.
Established Calorific Value
Async Additions
Additional information, related to Established Calorific
Value, needed when using asynchronous communication.
This is however not used when specifying the payload in the
ebIX® model, but is used when specifying the document in
the ebIX® model.
ebIX® Business Requirements for Measure Calorific Value 17
ebIX® September, 2015
2.3.1.1. Established Calorific Value (State Diagram)
Figure 17 SD Established Calorific Value
ebIX® Business Requirements for Measure Calorific Value 18
ebIX® September, 2015
2.3.2. Request Established Calorific Value Per MP (Class Diagram)
Figure 18 Request Established Calorific Value Per MP
ebIX® Business Requirements for Measure Calorific Value 19
ebIX® September, 2015
Element definitions, Request Established Calorific Value Per MP
«Business entity»
Request Established Calorific
Value Per MP
The information set sent by a Supplier when requesting a set
of Established Calorific Value Per MP for a Metering Point
from the Calorific Value Calculator.
Observation Period A specific period of time for which the requested established
calorific value per MP is valid.
«Business entity»
Metering Point
An entity where energy products are metered or computed.
Identifier The unique identification of the Metering Point to which the
requested established calorific value is attributed.
Request Established Calorific
Value Per MP Additions
Additional information, related to Request Established
Calorific Value Per MP the use of which may be agreed on a
national level. This is however not used when specifying the
payload in the ebIX® model.
Identifier The unique identification of this request as given by the
Supplier.
Request Established Calorific
Value Per MP Async Additions
Additional information, related to Request Established
Calorific Value Per MP, needed when using asynchronous
communication. This is however not used when specifying
the payload in the ebIX® model, but is used when specifying
the document in the ebIX® model.
none
2.3.2.1. Request (State Diagram)
Figure 19 SD Request Established Calorific Value Per MP
ebIX® Business Requirements for Measure Calorific Value 20
ebIX® September, 2015
2.3.3. Established Calorific Value Per MP (Class Diagram)
Figure 16 Established Calorific Value Per MP
ebIX® Business Requirements for Measure Calorific Value 21
ebIX® September, 2015
Element definitions, Established Calorific Value Per MP
«Business entity»
Established Calorific Value Per
MP
The information set containing a set of Established Calorific
Value Per MP, sent by a Calorific Value Calculator to a
Supplier to facilitate the financial settlements with either
the wholesale supplier of gas or with the end customer.
Observation Period A specific period of time describing the validity of this
recalculated calorific value per MP.
Measure Unit The unit of measure used for the quantity in these measured
data.
Calorific Value The established calorific value per MP for this observation
«Business entity»
Metering Point
An entity where energy products are metered or computed.
Identifier The unique identification of the Metering Point to which the
established calorific value per MP is attributed.
Established Calorific Value Per
MP Additions
Additional information, related to Established Calorific Value
per MP the use of which may be agreed on a national level.
This is however not used when specifying the payload in the
ebIX® model.
Identifier The unique identification of this set of information as given
by the Calorific Value Calculator.
Established Calorific Value Per
MP Async Additions
Additional information, related to Established Calorific Value
per MP, needed when using asynchronous communication.
This is however not used when specifying the payload in the
ebIX® model, but is used when specifying the document in
the ebIX® model.
Reference to Request Information about the request for this established calorific
value per MP which uniquely identifies it.
2.3.3.1. Established Calorific Value Per MP (State Diagram)
Figure 17 SD Established Calorific Value Per MP
ebIX® Business Requirements for Measure Calorific Value 22
ebIX® September, 2015
2.3.4. Negative Response to Request Established Calorific Value per MP (Class Diagram)
Figure 20 Negative Response to Request Established Calorific Value per MP
ebIX® Business Requirements for Measure Calorific Value 23
ebIX® September, 2015
Element definitions, Negative Response to Request Established Calorific
Value per MP
«Business entity»
Negative Response to Request
Established Calorific Value
per MP
The response sent by a Calorific Value Calculator to the
Supplier requesting established calorific value per MP when
not in the position to respond with the requested
established calorific value per MP.
Reason for Failure A code specifying the reason for this negative response.
Negative Response to Request
Established Calorific Value
per MP Additions
Additional information, related to Negative Response to
Request Established Calorific Value per MP the use of which
may be agreed on a national level. This is however not used
when specifying the payload in the ebIX® model.
Identifier The unique identification of this response as given by the
Calorific Value Calculator.
Negative Response to Request
Established Calorific Value
per MP Async Additions
Additional information, related to Negative Response to
Request Established Calorific Value per MP, needed when
using asynchronous communication. This is however not
used when specifying the payload in the ebIX® model, but is
used when specifying the document in the ebIX® model.
Reference to Request Information about the request leading to this response,
which uniquely identifies it.
2.3.4.1. Negative Response to Request Established Calorific Value per
MP (State Diagram)
Figure 21 SD Negative Response to Request Established Calorific Value per MP