Post on 14-Jul-2018
transcript
DETAIL DRAWING
INDEXFOR
SECURITYDOOR
LOUVERS
MODEL DESCRIPTION DATE PRINTED PAGEPLSL. . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum Security and Impact . . . . . . . . . . . . . . . . . . . . . March 2012 . . . . . . . . . . . 1FLDL-UL-SG1 . . . . . . . . . . . . . . . . . . Fire Rated Fusible Link with Security Grille One Side . . . . . March 2012 . . . . . . . . . . . 2FLDL-UL-SG2 . . . . . . . . . . . . . . . . . . Fire Rated Fusible Link with Security Grilles Two Sides. . . . March 2012 . . . . . . . . . . . 3DSFP . . . . . . . . . . . . . . . . . . . . . . . . . . Security Grille Face Plate. . . . . . . . . . . . . . . . . . . . . . . . . . July 2011 . . . . . . . . . . . . 4DSFP-Perf . . . . . . . . . . . . . . . . . . . . . Perforated Security Grille Face Plate. . . . . . . . . . . . . . . . . July 2011 . . . . . . . . . . . . 5Fasteners for Security Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . July 2011 . . . . . . . . . . . . 6
MARCH 2012SECURITY DOOR LOUVERS INDEX PAGE A
TECHNICAL DATAFROM
D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219
PH: 210.662.6300 • FAX: 210.662.2828e-mail: door@anemostat.com • website: www.anemostat.com
PLSL is not fire rated.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Hot
FINISH: Custom Baked Enamel Colors (as per sample chip, supplied by customer).FASTENERS: Special Security Screw Fasteners, See Page 26, this section.
Dipped or Zinc Plated). Not Available in Galvanized Coil.
SPECIALS: Fractional sizes (frame dimension is increased to accommodate odd sizes).Mesh insect screens are loose, attached or framed.(Galvanized, Aluminum, Charcoal Aluminum, Stainless Steel.)
MATERIAL: 12 GA. (2.5mm) Cold Rolled Steel Security Grille Frame with 13/16 (21mm) square holes on 1" (25mm) centers. 20 ga. (1mm) Cold Rolled Steel - Louver Blades.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the
perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 phillips head thru bolts (standard) or one way vandal proof security screws (must specify) with a blank head on one side for flush appearance.
DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors. Can be used in door thicknesses over 1-3/8" (35mm).
USES: For use where air flow is required in a security or Vandal resistant application.
1 3/8" MIN(35mm) 3/32"
(2mm)
1 1/16"(27mm)
3/8"(10mm)
FRAMEO.D.
ORDE
R SIZE
PLUS
2" (5
1mm)
ORDE
R SIZE
MINU
S 1/8"
(3mm
)
For detail drawings see page 12 & 13, Louver section. Refer to model FDLS.
FREE AIR FLOW: 50% Free Area.
12 GA. (2.5mm) C.R.S.FRAME / SECURITYGRILLE FACE PLATEWITH 13/16" (21mm)SQ. HOLES ON 1" (25mm) CTRS
OUTSIDE INSIDE
12 GA. (2.5mm) SECURITY
GRILLEORDER
SIZE&
DOORCUTOUT
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
Anemostat manufacturing dimensions ±1/32 (1mm)Actual dimensions are nominal and may varybased on component manufacturers tolerances.
PLSLLOUVER WITH SECURITY GRILLE
NON-VISIONINVERTED SPLIT Y
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS
NOT FIRE RATED
HURRICANE TEST / WINDSTORM APPROVALS (W/ U.L. MARKING)■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and
ANSI 250.13-Impact 350 FT LBS. Design Pressure: +/- 70 PSF (large missile test).■ Complies with Florida Building Code Standards■ Maximum size for hurricane use is 36" x 72" (914mm x 1829mm)
Florida Building CodeHurricane ApprovalFILE #FL11757
HURRICANE RATINGS
UNDERWRITERS’LABORATORIESFILE #R26087
Job Name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .comMARCH 2012
SECURITY DOOR LOUVERS PAGE 1
TECHNICAL DATAFROM
DETAIL DRAWING
D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219
PH: 210.662.6300 • FAX: 210.662.2828e-mail: door@anemostat.com • website: www.anemostat.com
20/45/60/90 MINUTE: Approved listing
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized
FINISH: Custom Baked Enamel Colors (as per sample chip supplied by customer).FASTENERS: Special Security Screw Fasteners, See Page 26, this section. SPECIALS: Fractional sizes not available.SCREENS:
MATERIAL: 18 GA. (1.2mm) Cold Rolled Steel Louver Blades and Inside Frame.
FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Self attaching using #8 x 1" (25mm) one way vandal
proof security screws that fasten the auxiliary frame to the louver core, thru the cut out in the door. The corridor side of the frame is free of fasteners for added security.
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.
CLOSING ASSEMBLY: Stainless steel operating springs assureproper action with the closing mechanism.
AESTHETICS: Tight mitered corners and countersunk mountingholes make for a clean appearance.
USES: In fire rated security door applications.FREE AIR FLOW: 40% Free Area.
- max width 24" (610mm), max height 24" (610mm)min width 10" (254mm), min height 6" (152mm)
(Zinc Plated). Not available in Galvanized Coil or Hot Dipped.12 GA. (2.5mm) Cold Rolled Steel Security Grille Frame (one side only)Face Plate with 13/16 (21mm) square holes on 1" (25mm) centers.
ORDERSIZE
&DOOR
CUTOUT
ORDE
R SIZE
PLUS
2" (5
1 mm)
FRAMEO.D.
STAINLESS RIVETS
165° F (74° C) FUSIBLE LINK& HEAT SLOT
AT TOP STOPBLADE
OUTSIDEINSIDE
1"
FINGER PULL(ALWAYS ON
LOWER RIGHT HAND SIDE)
ORDE
R SIZE
MINU
S 1/8"
(3 m
m)
SPRING CLIP
3/32"(5 mm)
(25 mm)
3/4"(19mm)
Grille on two sides.Also Available with Security( )See Page 24
1 3/16"(30 mm)
Anemostat manufacturing dimensions ±1/32 (1mm)Actual dimensions are nominal and may varybased on component manufacturers tolerances.
12 GA. (2.5mm)C.R.S. FRAME / SECURITYGRILLE FACE PLATEWITH 13/16" (21mm) SQ. HOLES ON 1" (25mm) CTRS
DOOR THICKNESS: 1 3/4" (44mm) Door is Standard. Also available for up to2-1/2" (64mm) Door. (to maintain fire rating).
1 3/4"(44 mm)
UP TO 2-1/2" (64mm)
12 GA. (2.5mm)SECURITY
GRILLE
Mesh insect screens are loose, attached or framed. (Galvanized, Aluminum, Charcoal Aluminum, Stainless Steel.) See Louvers page 12 & 13.
DETAIL DRAWING
TECHNICAL DATAFROM
FLDL-UL-SG1FUSIBLE LINK LOUVER WITH SECURITY GRILLE ONE SIDE
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
MARCH 2012SECURITY DOOR LOUVERS PAGE 2
UNDERWRITERS’LABORATORIES
FIRE RATINGS
Job Name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219
PH: 210.662.6300 • FAX: 210.662.2828e-mail: door@anemostat.com • website: www.anemostat.com
HURRICANE TEST / WINDSTORM APPROVALS (W/ U.L. MARKING)
B.S.-476.22British Standard
Steel Doors - 2 hours. Tested to 610mm x 610mmBS 476.22British Standard
Florida Building Code
Hurricane Approval
FILE #FL11757
HURRICANE RATINGS
UNDERWRITERS’LABORATORIESFILE #R26087
■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and ANSI 250.13-Impact 350 FT LBS. Design Pressure: +/- 70 PSF (large missile test).
■ Complies with Florida Building Code Standards■ Maximum size for hurricane use is 24" x 24" (610mm x 610mm)
ORDERSIZE
&DOOR
CUTOUT
(MUST SPECIFY IF CUTOUT REQUIRED)
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized
FINISH: Custom Baked Enamel Colors (as per sample chip supplied by customer).FASTENERS: Special Security Screw Fasteners, See Page 26, this section. SPECIALS: Fractional sizes not available.
MATERIAL: 18 GA. (1.2mm) Cold Rolled Steel Louver Blades and Inside Frame.
FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Self attaching using #8 x 1" (25mm) one way vandal
proof security screws that fasten the auxiliary frame to the louver core, thru the cut out in the door. The corridor side of the frame is free of fasteners for added security.
DOOR THICKNESS: 1 3/4" (44mm) Door is Standard. Also available up to
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
CLOSING ASSEMBLY: Stainless steel operating springs assureproper action with the closing mechanism.
AESTHETICS: Tight mitered corners and countersunk mountingholes make for a clean appearance.
USES: In fire rated security door applications.FREE AIR FLOW: 40% Free Area.
(Zinc Plated). Not available in Galvanized Coil or Hot Dipped.12 GA. (2.5mm) Cold Rolled Steel Security Grille Frame (two sides)Face Plate with 13/16 (21mm) square holes on 1" (25mm) centers.
ORDE
R SIZE
PLUS
2" (5
1 mm)
FRAMEO.D.
STAINLESS RIVETS
STOPBLADE
for 2-1/2" (64mm) Door. (to maintain fire rating).
OUTSIDEINSIDE
1"
FINGER PULL(ALWAYS ON LOWERRIGHT HAND SIDE)OPTIONAL CUTOUT
IN FACE GRILLETO ASSIST
FINGER PULL OPERATION
ORDE
R SIZE
MINU
S 1/8"
(3 m
m)
SPRING CLIP
Grille on one side onlyAlso Available with Security
See Page 233/32"
(5 mm)
(25 mm)
1 9/16"(40 mm)
( )
Anemostat manufacturing dimensions ±1/32 (1mm)Actual dimensions are nominal and may varybased on component manufacturers tolerances.
12 GA. (2.5mm) C.R.S.TWO SIDES FRAME / SECURITY GRILLE FACE PLATE W/ 13/16" (21mm) SQ. HOLES ON 1" (25mm) CTRS
12 GA. (2.5mm)SECURITY
GRILLE
20/45/60/90 MINUTE: Approved listing
SCREENS:
- max width 24" (610mm), max height 24" (610mm)min width 10" (254mm), min height 6" (152mm)
Mesh insect screens are loose, attached or framed. (Galvanized, Aluminum, Charcoal Aluminum, Stainless Steel.) See Louvers page 12 & 13.
165° F (74° C) FUSIBLE LINK& HEAT SLOT
AT TOP
1 3/4"(44 mm)
UP TO 2-1/2" (64mm)
IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.
DETAIL DRAWING
TECHNICAL DATAFROM
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure
MARCH 2012SECURITY DOOR LOUVERS PAGE 3
Job Name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219
PH: 210.662.6300 • FAX: 210.662.2828e-mail: door@anemostat.com • website: www.anemostat.com
Steel Doors - 2 hours. Tested to 610mm x 610mmBS 476.22British Standard
FLDL-UL-SG2FUSIBLE LINK LOUVER WITH
SECURITY GRILLE TWO SIDES
UNDERWRITERS’LABORATORIES
FIRE RATINGS
B.S.-476.22British Standard
Florida Building Code
Hurricane Approval
FILE #FL11757
HURRICANE RATINGS
UNDERWRITERS’LABORATORIESFILE #R26087
HURRICANE TEST / WINDSTORM APPROVALS (W/ U.L. MARKING)■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and
ANSI 250.13-Impact 350 FT LBS. Design Pressure: +/- 70 PSF (large missile test).■ Complies with Florida Building Code Standards■ Maximum size for hurricane use is 24" x 24" (610mm x 610mm)
Job Name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .comJULY 2011
SECURITY DOOR LOUVERS PAGE 4
ORDER SIZE WIDTH
Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.
DSFP is not fire rated.
MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized
FINISH: Custom Baked Enamel Colors (as per sample chip,
FASTENERS: Special Security Screw Fasteners, See Page 26, this section.
NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.
(Hot Dipped or Zinc Plated). 10 gauge or 7 gauge.
supplied by customer).
SPECIALS: Fractional sizes, and other face plate patterns.
MATERIAL: 12 GA. Cold Rolled Steel Lattice Face Plate SecurityGrille (with 13/16" square holes on 1" centers.)
FINISH: Grey Primer, Beige or Bronze Baked Enamel.
#8X1" one way vandal proof security screws, thatcan be screwed directly thru the face plate
INSTALLATION: Frame has countersunk mounting holes for
into wall or door.DOOR OR WALL THICKNESS: Will work on any thickness based
FREE AIR FLOW: 66% Free Area.
3/8"(10mm)
13/16" (21mm) SQUARE HOLESON 1" (25mm) CENTERS
3/16"(5mm)
#8X1" ONE WAY VANDAL PROOF SECURITY SCREWS (HOLE LOCATION AND QUANTITY WILL VARY BY SIZE)
12 GA. STEEL(7/64")
on ability to accept a screw or fastener.
IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.
FRAME O.D.
OPENING AREAORDER SIZE LESS 2 3/16" (56mm)
OPENING AREAORDER SIZE LESS 2 3/16" (56m
m)
1 3/32"(27mm)
ORDERSIZE
HEIGHT
FRAMEO.D.
(3mm)
TECHNICAL DATAFROM
DETAIL DRAWING
DSFPSECURITY GRILLE
FACE PLATE
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS
NOT FIRE RATEDD o o r P r o d u c t s
4958 Stout Dr. #119, San Antonio, TX 78219PH: 210.662.6300 • FAX: 210.662.2828
e-mail: door@anemostat.com • website: www.anemostat.com
JULY 2011SECURITY DOOR LOUVERS PAGE 5
Job Name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .com
D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219
PH: 210.662.6300 • FAX: 210.662.2828e-mail: door@anemostat.com • website: www.anemostat.com
All Dimensions ±1/32
12 GA. STEEL (7/64")(3mm)
FRAME O.D.ORDER SIZE WIDTH
FRAMEO.D.
ORDERSIZE
HEIGHT
* 1-3/16" (30mm) BORDER IS APPROXIMATE. THIS DIMENSION IS A
#8 x 1" ONE WAY VANDAL PROOF SECURITY SCREWS (HOLE LOCATION AND QUANTITY WILL VARY BY UNIT SIZE)
FUNCTION OF SIZE AND PERFORATED PATTERN.
1 3/16" *(30mm)
5/16" (8mm) DIAM. HOLESON 7/16" (11mm) STG. CTRS.
1 3/16" *(30mm)
OPENING AREAORDER SIZE LESS 2 3/8" (60mm)
OP
EN
ING
AR
EA
OR
DE
R S
IZE
LES
S 2 3/8 (60m
m)
3/8"(10mm)
TECHNICAL DATAFROM
DETAIL DRAWING
DSFP-PerfPERFORATED
SECURITY GRILLEFACE PLATE
STANDARD PRODUCT FEATURES OPTIONAL FEATURES
FIRE RATINGS
NOT FIRE RATED
■ MATERIAL: 12 GA. Cold Rolled Steel Perf. Face Plate Security Grille (with 5/16" diam. holes on 7/16" stag. ctrs.)
■ FINISH: Grey Primer, Beige or Bronze Baked Enamel.■ INSTALLATION: Frame has countersunk mounting holes for #8 x 1" One Way
Vandal Proof Screws that can be screwed directly thru theface plate into the wall or door.
■ FREE AIR FLOW: 46% Free Area.■ NOTE: For Exterior use, High Humidity or Salt Air application, product must
be Galvanized or Stainless Steel.■ IMPORTANT: Interpretation of building and fire codes may vary.
Consult with the local authority having jurisdiction in yourarea, to determine appropriate standards.
■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Hot Dipped or Zinc Plated). 10 gauge or 7 gauge.
■ FINISH: Special order Baked Enamel Colors (as per sample chip, supplied bycustomer).
■ FASTENERS: Special Security Screw Fasteners Available.■ SPECIALS: Fractional sizes, and other face plate patterns. Consult Factory.
Can be fabricated without screw holes.
■ DSFP-Perf is not fire rated.
Job Name & Location Submitted by
For Most Current Info, Consult Factory or check our website, www.anemostat .comJULY 2011
SECURITY DOOR LOUVERS PAGE 6
#8X32 THRU BOLT, BLANK ONE ENDUSED FOR ALL MODELS: SG-10, SG-12, SL-IS, FGS, PLSL AND BR-7
*Screwdrivers and insert bits for Security Fasteners are available.Consult Factory for Price and Availability.
ONE WAY VANDALPROOF SECURITY SCREW#8X1" USED FOR: DSFP, FLDL-UL-SG1, FLDL-UL-SG2#8X3/4" USED FOR: SG-10-SSD, SSD#8X1-3/4" USED FOR: LoPro-SC, LoPro-GR, LoPro-SC-GR, LoPro-SSD
3/8"
STANDARD
NOTCHED SPANNERHEAD SCREW
TORX-PLUS FLAT HEADSECURITY SCREW
(Available on all Security Products)
SECURITY SCREWTORX FLAT HEAD SOCKET
SNAKE EYE SPANNERFLAT HEAD SECURITY SCREW(DRILLED SPANNER)
PINNED FLAT HEAD CAP SCREW(TAMPER RESISTANT HEX SOCKET)
ONLY AVAILABLE ONCERTAIN APPLICATIONS
OPTIONAL SECURITY FASTENERS*
1/4"X20 THRU BOLT BLANK ONE END-MEETS ASTM F-1450-97 (MUST SPECIFY): SG-10, BR-7, SG-12-SP, SG-10-SP, SG-12-LSC
TECHNICAL DATAFROM
DETAIL DRAWING
FASTENERSFOR
SECURITY VISION FRAMESAND
SECURITY DOOR LOUVERSD o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219
PH: 210.662.6300 • FAX: 210.662.2828e-mail: door@anemostat.com • website: www.anemostat.com