Post on 01-Sep-2020
transcript
E-CAT6-P-SJM-00-A
60Hz
Motor pumps
SJM2/SJM3
Foot valve
Special companion flange
Different diameter pipe
* Keep in mind that outline drawings, etc., differ from standard drawings in the case of change to special specifications.
※1 Differs with types.
Foot valvenominaldiameter
mm
Differentdiameter pipe
Specialcompanion
flange
Nominaldiameter
mm
Suctions
Discharged
32 32 32 − −
40 40 40 − −
50 40 50 − 40/50
65 50 65 − 50/65
80 65 100 80×100 65/80
* Use the special companion flange for making the discharge diameter identical to the suction diameter.
■Foot valve, different diameter pipe, and special companion flange application table
■Standard specifications
■Standard accessories
■Special specifications
■Special accessories
* Keep in mind that some of the devices in the photo may differ from actual devices in coating color, etc.
■Uses
■Features
●General water supply for buildings, condominiums, etc.
●Circulation of cold/warm water
●Conveyance of industrial water
●Conveyance and distribution of tap water
●Irrigation of paddies and fields
●Water sprinkling
①Compact and lightweight through the adoption of 2-pole motor.②Large-type-level performance covering a wide range of uses.③Easy to install, and does not require a large space.④Easy to perform maintenance and inspection as disassembly and
reassembly can be performed without removing piping due to the B.P.O (back pull out) structure.⑤Advantageous to piping load by stable installation due to straight-up discharge.⑥Compliant with JIMS (The Japan Society of Industrial Machinery Manufacturers)
10BAR class.
Foot valveSuction coverSluice valve, check valve ……………………Packing, bolt, and nut includedCompanion flange ……………………………Packing, bolt, and nut included* Standard accessory for 32mm in nominal diameter.Special companion flange (for making the discharge diameter identical to the suction diameter) ………………Nut and bolt includedDifferent diameter pipe ……………………………See the illustration below.Anti-vibration mountPressure gauge, vacuum gauge, compound gauge ……Cock and pipe includedAnti-vibration joint
Motor ……………………………………………………………………………1Common base …………………………………………………………………1Companion flange (packing, bolt, and nut included) (nominal diameter 32mm only) ………2 setsPriming plug ……………………………………………………………………1
Motor change Voltage change
Material change Total-ironLiquid quality…Fresh water
Liquid temperature…0 – 80°C
-6m (20°C)
See the specifications table.
Impeller…Closed
Bearing…Sealed ball bearing
Shaft seal…Mechanical seal
Impeller…CAC406 or SCS13※1
Shaft…SUS304
Casing…FC200 or FCD450※1
Type…SJM2…Totally-enclosed-fan-cooled outdoor type
SJM3…Totally-enclosed-fan-cooled outdoor type
Power supply…Three-phase, 200/220V
Synchronous rotation speed…3600min-1
JIS 10K (normal) (special dimensions for nominal diameter 32)
7.5BG5/1.5
Allowable push-in pressure
Flange spec
Coating color
Pumping liquid
Structure
Material
Motor
Total suction head
■Model type description
SJM2 - 32 × 32 L 6 .75
①Model②Nominal suction diameter (32mm)③Nominal discharge diameter (32mm)
④Frequency (60Hz)⑤Output (0.75kW)
① ② ③ ④ ⑤
2-pole motor typeCast-ironNon-submersible pumps
Volute pumps SJM3 modelSJM2 model
2
SJM2-32×32L6.75SJM2-32×32L61.5SJM2-32×32M62.2SJM2-32×32M63.7SJM2-40×40L6.75SJM2-40×40L61.5SJM2-40×40M62.2SJM2-40×40M63.7SJM2-50×40L62.2SJM2-50×40M63.7SJM3-50×40M65.5SJM3-50×40H65.5SJM3-50×40H67.5SJM3-65×50L63.7SJM3-65×50M65.5SJM3-65×50M67.5SJM3-65×50H67.5SJM3-80×65L65.5SJM3-80×65L67.5
SJM2-32×32L6.75SJM2-32×32L61.5SJM2-32×32M62.2SJM2-32×32M63.7SJM2-40×40L6.75SJM2-40×40L61.5SJM2-40×40M62.2SJM2-40×40M63.7SJM2-50×40L62.2SJM2-50×40M63.7
H-16H-20HH-20HH-20HH-16
H-20HH-20HH-20HH-20HH-20H
G140G140K184K184G140G140K184K184G140K184
P22P22P22P22P22P22P22P22P22P22
0.751.52.23.70.751.52.23.72.23.75.55.57.53.75.57.57.55.57.5
0.050.050.050.050.10.10.10.10.120.120.120.120.120.250.250.250.250.50.5
2134.54355192938533147515669.531.54347.852.229.235
0.10.10.10.10.180.180.180.180.250.250.250.250.250.50.50.50.51.01.0
2033.542.553152633.550.5284346.551652636.841.546.52430
0.150.150.150.150.270.270.270.270.380.380.380.330.380.70.70.70.571.321.5
17.531.54151.59.51928.547223638.544.554.518.5283443.71820
0.590.590.520.400.590.590.590.400.590.500.450.440.290.590.550.490.460.590.59
32
40
50
65
80
32
40
40
50
65
ModelOutput
kW Discharge ratem3/min
Discharge ratem3/min
Discharge ratem3/min
Total headm
Total headm
Total headm
Allowablepush-in pressure
MPa
Nominal diameter mm
Suction Discharge
Specifications
<60Hz> Synchronous rotation speed 3600 min-1
Discharge rate (m3/min)
Total head (m)
■Performance drawing
■Specifications table
■Parts list
SJM3-50×40M65.5SJM3-50×40H65.5SJM3-50×40H67.5SJM3-65×50L63.7SJM3-65×50M65.5SJM3-65×50M67.5SJM3-65×50H67.5SJM3-80×65L65.5SJM3-80×65L67.5
H-25H-1H-25H-1H-25H-1H-20H
H-25H-1H-25H-1H-25H-1H-25H-1H-25H-1
K184K223K223G140K184K184K223K160K160
P22P22P22P22P22P22P22P22P22
90
80
70
60
50
40
30
20
15
10
90.04 0.05 0.07 0.1 0.15 0.2 0.3 0.4 0.5 0.7 1.0 1.5 2.0
32×32M63.7
32×32M62.2
32×32L61.5
40×40 L6.75
50×40L62.2
50×40M63.740×40
M62.2
40×40 M63.7
40×40L61.5 65×50L63.7
65×50 M65.5
80×65L65.5
50×40H67.5
65×50H67.565×50M67.5
80×65L67.5
50×40H65.5
50×40M65.5
32×32L6.75
32×32M63.7
32×32M62.2
32×32L61.5
40×40 L6.75
50×40L62.2
50×40M63.740×40
M62.2
40×40 M63.7
40×40L61.5 65×50L63.7
65×50 M65.5
80×65L65.5
50×40H67.5
65×50H67.565×50M67.5
80×65L67.5
50×40H65.5
50×40M65.5
32×32L6.75
■Motor specifications table
0.751.52.23.75.57.5
3.1/3.06.2/5.88.6/7.8
14.0/13.021.0/19.527.5/25.0
3450/34803370/34203360/34103380/34203520/35303510/3520
307/372241/291255/309245/295215/260232/281
23.9/26.337.5/41.554.6/60.0
96/105132/145178/196
Direct-on-Line startDirect-on-Line startDirect-on-Line startDirect-on-Line startDirect-on-Line startDirect-on-Line start
FFFFFF
6205ZZC36306ZZC36306ZZC36307ZZC36308ZZC36308ZZC3
6204ZZC36205ZZC36205ZZC36306ZZC36306ZZC36306ZZC3
200/220200/220200/220200/220200/220200/220
Phase VoltageV
CurrentA
Rotation speedmin-1
Protection methodOutput
kWHeat-resistance
class
Classification RatingTorque
%Current
AMethod
StartingLoad side
(D.S)Anti-load side
(O.S)
Bearing
Three-phase
Totally-enclosed-fan-cooledoutdoor type
Pump typeMechanical seal
typeO-ring
(for casing)O-ring
(for priming plug) Pump typeMechanical seal
typeO-ring
(for casing)O-ring
(for priming plug)
2-pole motor typeCast-iron Non-submersible pumps
Volute pumpsSJM3 modelSJM2 model
3
※SJM2-32×32L6.75※SJM2-32×32L61.5※SJM2-32×32M62.2※SJM2-32×32M63.7SJM2-40×40L6.75SJM2-40×40L61.5SJM2-40×40M62.2SJM2-40×40M63.7SJM2-50×40L62.2SJM2-50×40M63.7
0.751.52.23.70.751.52.23.72.23.7
75757575757575758080
314356351390314356351390356390
142142162162142142162162142162
120120160160120120160160140160
224233233266224224233266233266
111118118139111118118139118139
150150185185150150185185150185
210210260260210210260260210260
160160190190160160190190160190
32364154323642554058
32 32
40 40
50 40
A B D E KA KG L BN BX BP
(Unit: mm)
※The pump flange nominal diameter of SJM2-32x32 is 40. (The pump nominal diameter is called 32mm according to special companion flange.)
■Size table
●SJM2 type
●SJM3-65×50L63.7
Flange dimensions: JIS 10K flange or equivalent
Flange dimensions: JIS 10K flange or equivalent
Approx. mass 50kg
■Assembly drawing
■Assembly drawing
Disassembly dimensions 100
(62)
(139)
φ65
30
140
142
399
275
2×φ15 Drain plug1/4B
95
250 150
400
(Recommended foundation bolt FD)
PF 3/4
80
φ50
230
160
Rotation direction
Plug3/8B
(Foundation bolt hole)
PF½PF¾PF¾PF¾PF½PF¾PF¾PF¾PF¾PF¾
45
200BP
2-M10 recommended foundation bolt
95
150BN
DEφs
φd
A
BX
45
(KG)
Disassembly dimensions 100
L
(62)
B
KA Rotation direction
Plug3/8B
Drain plug1/4B
Nominal diameter
Suctions
Discharged
ModelOutput
kW
Pump and motor Common base Approx.mass
kg
2-pole motor typeCast-ironNon-submersible pumps
Volute pumps SJM3 modelSJM2 model
4
50 40SJM3-50×40M65.5SJM3-50×40H65.5SJM3-50×40H67.5SJM3-65×50M65.5SJM3-65×50M67.5SJM3-65×50H67.5SJM3-80×65L65.5SJM3-80×65L67.5
5.55.57.55.57.57.55.57.5
8080808080
100100100
456456493456493493456493
207210210207207210207207
160180180160160180160160
396396433396433433396433
190190190190190212190190
260260260260260282260260
7679857884887884
65 50
80 65
A B D E KA BP BX
■Assembly drawing
■Size table
Flange dimensions: JIS 10K flange or equivalent
(Unit: mm)
Disassembly dimensions 100
PF 1 1/4
100 220
470
(Foundation bolt hole)
Drain plug1/4B
Plug3/8B
150
95 BP
BX
(Foundation bolt hole)
50
DEφs
186
B
KA
φd
A
237
Rotation direction
4×φ15 hole(Recommended foundation bolt M12)
Nominal diameter
Suctions
Discharged
ModelOutput
kW
Pump and motor Common base Approx.mass
kg
2-pole motor typeCast-iron Non-submersible pumps
Volute pumpsSJM3 modelSJM2 model
5
■Example of internal structure diagram ■Parts list●SJM2 type
●SJM3 type
No. Part name Qty Material123456789
1011121314151617
CasingFrameImpellerImpeller nutWearing ringCommon bedKeyDeflectorMechanical sealO-ringO-ringWearing ringPlugPlugMotor shaftSupport boltMotor
11111111111111121
FC200FC200CAC406SUS304CAC406SS400SUS304CRCERAMICS~CARBONNBRNBRCAC202SS400SS400Wetted part SUS 304SS400 ー
No. Part name Qty Material123456789
101112131415161718
CasingFrameImpellerImpeller nutWearing ringWearing ringCommon baseKeyDeflectorMechanical sealO-ringO-ringPriming plugPlugPlugMotor shaftSupport boltMotor
※1 Differs with types.
111111111111121121
FC200 or FCD450※1
FC200CAC406 or SCS13※1
SUS304CAC406CAC406SS400SUS304CRCERAMICS~CARBONNBRNBRCAC202SUS304SUS304Wetted part SUS 304SS400 ー
14 4 8 13 12 10 16 9 18
1 5 15 3 6 11 2 7 17
1
4 12 11 9 8
621035
7
16
13
14
1715
2-pole motor typeCast-ironNon-submersible pumps
Volute pumps SJM3 modelSJM2 model
6
MEMO
E-CAT6-P-SJM-00-A
60Hz
Motor pumps
SJM2/SJM3
150 Moo 16 Udomsorayuth Rd., T.Bangkrasan, A.Bangpa-In, Ayutthaya 13160 Thailand Tel.+66-3522-0640 Fax.+66-3522-1259
No.285, Yuan Qu Road(N), Bei Qiao, Min Hang District, Shanghai 201109, China Tel.+86-21-6490-9128 Fax.+86-21-6490-9126
Room 1001, 10/F, Olympia Plaza, 255 King|s Road, North Point, Hong Kong Tel.+852-2571-0886 Fax.+852-2571-0619
Head Office 230, Moriwake, Miyuki-cho, Fukuyama-city, Hiroshima, 720-0003, Japan Tel.+81-84-955-1111 Fax.+81-84-955-5777