Post on 22-Oct-2020
transcript
1SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
User's GuideSLAU739–October 2017
MSP430FR2433 LaunchPad™ Development Kit(MSP‑‑EXP430FR2433)
The MSP-EXP430FR2433 LaunchPad™ Development Kit is an easy-to-use evaluation module (EVM) based on the MSP430FR2433 Value Line Sensing microcontroller (MCU). It contains everything needed to start developing on the ultra-low-power MSP430FR2x Value Line Sensing MCU platform, including onboard debug probe for programming, debugging, and energy measurements. The board includes two buttons and two LEDs for creating a simple user interface. It also supports using a supercapacitor (must be purchased and installed by the user) that acts like a rechargeable battery, enabling stand-alone applications without an external power supply.Figure 1 shows the MSP-EXP430FR2433 LaunchPad development kit.
Figure 1. MSP-EXP430FR2433 LaunchPad Development Kit
www.ti.com
2 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
Contents1 Getting Started ............................................................................................................... 3
1.1 Introduction .......................................................................................................... 31.2 Key Features ........................................................................................................ 31.3 What's Included ..................................................................................................... 31.4 First Steps: Out-of-Box Experience .............................................................................. 41.5 Next Steps: Looking Into the Provided Code ................................................................... 4
2 Hardware...................................................................................................................... 52.1 Block Diagram....................................................................................................... 52.2 Hardware Features ................................................................................................. 62.3 Power ............................................................................................................... 102.4 Measure Current Draw of the MSP430 MCU.................................................................. 122.5 Clocking ............................................................................................................ 122.6 Using the eZ-FET Debug Probe With a Different Target .................................................... 122.7 BoosterPack Pinout ............................................................................................... 132.8 Design Files ........................................................................................................ 142.9 Hardware Change log ............................................................................................ 14
3 Software Examples ........................................................................................................ 143.1 Out-of-Box Software Example ................................................................................... 153.2 Blink LED Example................................................................................................ 16
4 Resources ................................................................................................................... 164.1 Integrated Development Environments......................................................................... 164.2 LaunchPad Websites ............................................................................................. 194.3 MSPWare and TI Resource Explorer........................................................................... 204.4 FRAM Utilities...................................................................................................... 204.5 MSP430FR2433 MCU ............................................................................................ 214.6 Community Resources ........................................................................................... 21
5 FAQ .......................................................................................................................... 216 Schematics.................................................................................................................. 22
List of Figures
1 MSP-EXP430FR2433 LaunchPad Development Kit .................................................................... 12 MSP-EXP430FR2433 Overview ........................................................................................... 53 MSP-EXP430FR2433 Block Diagram..................................................................................... 54 MSP430FR2433 Pinout..................................................................................................... 65 eZ-FET Debug Probe ....................................................................................................... 76 eZ-FET Isolation Jumper Block Diagram ................................................................................. 87 Application Backchannel UART in Device Manager .................................................................... 98 MSP-EXP430FR2433 Power Block Diagram........................................................................... 109 MSP-EXP430FR2433 Supercap Power Block Diagram .............................................................. 1110 BoosterPack Checker Tool ............................................................................................... 1311 LaunchPad Kit to BoosterPack Module Connector Pinout............................................................ 1412 TI Resource Explorer Cloud .............................................................................................. 1713 CCS Cloud .................................................................................................................. 1714 Directing the Project>Import Function to the Demo Project .......................................................... 1815 When CCS Has Found the Project ...................................................................................... 1916 Using TI Resource Explorer to Browse MSP-EXP430FR2433 in MSPWare ...................................... 2017 Schematics (1 of 2) ........................................................................................................ 2218 Schematics (2 of 2) ........................................................................................................ 23
List of Tables
1 EnergyTrace Technology ................................................................................................... 7
www.ti.com Getting Started
3SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2 Isolation Block Connections ................................................................................................ 83 Hardware Change Log .................................................................................................... 144 Software Examples ........................................................................................................ 145 IDE Minimum Requirements for MSP-EXP430FR2433 ............................................................... 146 Source File and Folders ................................................................................................... 157 Source File and Folders ................................................................................................... 168 How MSP Device Documentation is Organized........................................................................ 21
TrademarksLaunchPad, BoosterPack, Code Composer Studio, EnergyTrace, MSP430, E2E are trademarks of TexasInstruments.IAR Embedded Workbench is a registered trademark of IAR Systems.All other trademarks are the property of their respective owners.
1 Getting Started
1.1 IntroductionThe 16-MHz MSP430FR2433 device features 15.5KB of embedded FRAM (ferroelectric random accessmemory), a nonvolatile memory known for its ultra-low power, high endurance, and high-speed writeaccess. Combined with the 4KB of on-chip SRAM, users have access to 15.5KB of memory to splitbetween their program and data as required. For example, a data logging application may require a largedata memory with a relatively small program memory, so the memory may be allocated as requiredbetween program and data memory.
Rapid prototyping is simplified by the 20-pin BoosterPack™ plug-in module headers, which support a widerange of available BoosterPack modules. You can quickly add features like wireless connectivity, graphicaldisplays, environmental sensing, and much more. Design your own BoosterPack plug-in module orchoose among many already available from TI and third-party developers.
Free software development tools are also available, such as TI's Eclipse-based Code Composer Studio™IDE (CCS) and IAR Embedded Workbench® IDE. Both of these IDEs support EnergyTrace™ technologyfor real-time power profiling and debugging when paired with the MSP430FR2433 LaunchPaddevelopment kit.
1.2 Key Features• MSP ULP FRAM technology based MSP430FR2433 16-bit MCU• EnergyTrace Technology available for ultra-low-power debugging• 20-pin LaunchPad development kit standard leveraging the BoosterPack plug-in module ecosystem• Onboard eZ-FET debug probe• 2 buttons and 2 LEDs for user interaction
1.3 What's Included
1.3.1 Kit Contents• 1 MSP-EXP430FR2433 LaunchPad development kit• 1 Micro USB cable• 1 Quick start guide• The supercapacitor is not included and must be provided by the user
1.3.2 Software Examples• Out-of-Box Software
Getting Started www.ti.com
4 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
1.4 First Steps: Out-of-Box Experience
1.4.1
1.4.2
An easy way to get started with the EVM is by using its preprogrammed out-of-box code. This code demonstrates some key features of the EVM.
Connecting to the ComputerConnect the LaunchPad development kit to a computer using the included USB cable. A green power LED should illuminate. For proper operation, drivers are needed. It is recommended to get drivers by installing an IDE such as TI's CCS or IAR EW430. Drivers are also available at www.ti.com/MSPdrivers.
Running the Out-of-Box DemoThe out-of-box (OOB) demo for the MSP-EXP430FR2433 LaunchPad development kit demonstrates how to setup a periodic temperature data logger, by using a ring buffer inside the FRAM memory of the MSP430FR2433 MCU. Alternatively, the demo also implements a real-time temperature sensor.Both the logged and the real-time temperature data can be transmitted to the PC and visualized using the accompanying cloud GUI (visit MSP-EXP430FR2433 OOB GUI). If access to the cloud GUI is not available, the data can still be observed using any serial terminal application (application UART settings: 115200, 8, 1, n).By default after power up, the LaunchPad development kit enters the FRAM Data Log mode. The red LED1 blinks periodically (approximately every 5 seconds), which indicates that the device is waking up to log the temperature and going back to sleep. Press the left user button S1 to transfer the stored temperature to the PC.Next, try pressing the S1 and S2 buttons simultaneously to enter the Live Temperature mode. The LaunchPad development kit should start streaming live temperature data to the PC to be visualized in the MSP-EXP430FR2433 OOB GUI or displayed in a serial terminal. In this mode, the application also keeps track of a temperature threshold (the default is 25°C), and when a new temperature data is acquired, it is compared against that threshold. If the current temperature is above the threshold, the red LED1 illuminates, and if the current temperature is below the threshold, the green LED2 illuminates. Pressing S1 or S2 independently increases or decreases the temperature threshold in this mode.The user can influence the temperature of the device by blowing hot or cold air and observing the changes in the user LED brightness or see data changes on the GUI.
1.5 Next Steps: Looking Into the Provided CodeAfter the EVM features have been explored, the fun can begin. It is time to open an integrated development environment and start editing the code examples. See Section 4 for available IDEs and where to download them.The quickest way to get started using the LaunchPad development kit is to use TI's Cloud Development Tools. The cloud-based Resource Explorer provides access to all of the examples and resources in MSPWare software. Code Composer Studio Cloud is a simple cloud-based IDE that enables developing and running applications on the LaunchPad development kit.The out-of-box source code and more code examples are provided and available on the download page. Code is licensed under BSD, and TI encourages reuse and modifications to fit specific needs.Section 3 describes all functions in detail and provides a project structure to help familiarize you with the code.
With the onboard eZ-FET debug probe debugging and downloading new code is simple. A USB connection between the EVM and a PC through the provided USB cable is all that is needed.
Target device MSP430FR2433
Crystal 32.768 kHz
Micro-B USB
3.3-V LDO
ESD Protection
Debug MCU
LED Red, Green
Crystal, 4 MHz
UART, SBW to Target
User interface2 buttons, 2 LEDs
20-pinLaunchPad
standard headers
Power to Target
Reset button
EnergyTraceTechnology
Supercapacitor
www.ti.com Hardware
5SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2 HardwareFigure 2 shows an overview of the MSP-EXP430FR2433 hardware.
Figure 2. MSP-EXP430FR2433 Overview
2.1 Block DiagramFigure 3 shows the block diagram.
Figure 3. MSP-EXP430FR2433 Block Diagram
RST/NMI/SBWTDIO
TEST/SBWTCK
P1.4/UCA0TXD/UCA0SIMO/TA1.2/TCK/A4/VREF+
P1.5/UCA0RXD/UCA0SOMI/TA1.1/TMS/A5
P1.6/UCA0CLK/TA1CLK/TDI/TCLK/A6
P1.7/UCA0STE/SMCLK/TDO/A7
P1.0
/UC
B0S
TE
/TA
0C
LK
/A0/V
ere
f+
P1
.1/U
CB
0C
LK
/TA
0.1
/A1
P1
.2/U
CB
0S
IMO
/UC
B0S
DA
/TA
0.2
/A2/V
ere
f-
P1.3
/UC
B0S
OM
I/U
CB
0S
CL/M
CLK
/A3
P2.2
/SY
NC
/AC
LK
P3.0
P2.3
P3.1/UCA1STE
P2.4/UCA1CLK
P2.5/UCA1RXD/UCA1SOMI
P2.6/UCA1TXD/UCA1SIMO
DVSS
P2.7
P3.2
P2.0
/XO
UT
P2.1
/XIN
DV
SS
DV
CC
MSP430FR2433IRGE
1
2
3
4
5
6
7 8 9 10 11 12
13
14
15
16
17
18
192021222324
Hardware www.ti.com
6 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2.2 Hardware Features
2.2.1 MSP430FR2433 MCUThe MSP430FR2433 is an ultra-low-power MSP430FRx FRAM-based microcontroller (MCU), which offer extended data logging and security capabilities. The MSP430FR2433 offers the small VQFN package(4 mm × 4 mm) in the FRAM microcontroller portfolio, combined with a variety of integrated peripherals and ultra-low power consumption. FRAM is a cutting edge memory technology, combining the best features of flash and RAM into one nonvolatile memory. More information on FRAM can be found at www.ti.com/fram.
Device features include:• 1.8-V to 3.6-V operation• 16-bit RISC architecture up to 16-MHz system clock and 8-MHz FRAM access• 15KB of program FRAM, 512B of information FRAM, and 4KB of RAM• 8-channel 10-bit ADC• Four 16-Bit timers
– Two timers with three capture/compare registers each (Timer_A3)– Two timers with two capture/compare registers each (Timer_A2)
• 32-bit hardware multiplier (MPY)• 19 GPIOs• Two enhanced universal serial communication interfaces (eUSCI_A) support UART, IrDA, and SPI• One eUSCI (eUSCI_B) supports SPI and I2C
Figure 4. MSP430FR2433 Pinout
www.ti.com Hardware
7SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2.2.2 eZ-FET Onboard Debug Probe With EnergyTrace TechnologyTo keep development easy and cost effective, TI's LaunchPad development kits integrate an onboard debug probe, which eliminates the need for expensive programmers. The MSP-EXP430FR2433 has the eZ-FET debug probe (see Figure 5), which is a simple and low-cost debugger that supports all MSP430™ device derivatives.
Figure 5. eZ-FET Debug Probe
The MSP-EXP430FR2433 LaunchPad development kit features EnergyTrace technology but does nothave support for EnergyTrace++ technology. The EnergyTrace functionality varies across the MSPportfolio.
Table 1. EnergyTrace Technology
Features EnergyTrace Technology EnergyTrace++ TechnologyCurrent monitoring Yes YesCPU state No YesPeripheral and system state No Yes
Devices supported All MSP430 MCUs MSP430FR59xx andMSP430FR69xx MCUsDevelopment tool required MSP-FET or eZ-FET MSP-FET or eZ-FET
The dotted line through J101 shown in Figure 5 divides the eZ-FET debug probe from the target area. The signals that cross this line can be disconnected by jumpers on J101, the isolation jumper block. For more details on the isolation jumper block, see Section 2.2.3.The eZ-FET also provides a backchannel UART-over-USB connection with the host, which can be very useful during debugging and for easy communication with a PC. For more details, see Section 2.2.4.The eZ-FET hardware can be found in the schematics in Section 6 and in the MSP-EXP430FR2433 design files download page. The software and more information about the debugger can be found on the eZ-FET wiki. More information on the eZ-FET can be found in the MSP Debuggers User's Guide.
eZ-FET DebugProbe
Isolation Jumper Block
Spy
-Bi-W
ire (
SB
W)
Em
ulat
ion
App
licat
ion
UA
RT
3.3-
V P
ower
5-V
Pow
er
Target MSP430FR2433
eZ-F
ET
MS
P43
0 T
arg
et
USB Connector
in outLDO
Boo
ster
Pac
k H
eade
r
Boo
ster
Pac
k H
eade
r
USB
EnergyTraceTechnology
Hardware www.ti.com
8 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2.2.3 Debug Probe Connection: Isolation Jumper BlockThe isolation jumper block at jumper J101 allows the user to connect or disconnect signals that cross from the eZ-FET domain into the MSP430FR2433 target domain. This includes eZ-FET Spy-Bi-Wire signals, application UART signals, and 3.3-V and 5-V power. Table 2 describes these connections.Reasons to open these connections:• To remove any and all influence from the eZ-FET debug probe for high accuracy target power
measurements• To control 3-V and 5-V power flow between the eZ-FET and target domains• To expose the target MCU pins for other use than onboard debugging and application UART
communication• To expose the programming and UART interface of the eZ-FET so that it can be used for devices other
than the onboard MCU. See Section 2.6 for how to use the eZ-FET Debug Probe with a different target.
Table 2. Isolation Block Connections
Jumper DescriptionGND Ground5V 5-V VBUS from USB3V3 3.3-V rail, derived from VBUS in the eZ-FET domain
RXD > Backchannel UART: The target FR2433 sends data through this signal. The arrows indicate the directionof the signal.SBW RST Spy-Bi-Wire debug: SBWTDIO data signal. This pin also functions as the RST signal (active low).SBW TST Spy-Bi-Wire debug: SBWTCK clock signal. This pin also functions as the TST signal.
Figure 6. eZ-FET Isolation Jumper Block Diagram
www.ti.com Hardware
9SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2.2.4 Application (or Backchannel) UARTThe backchannel UART allows communication with the USB host that is not part of the target application's main functionality. This is very useful during development, and also provides a communication channel to the PC host side. This can be used to create graphical user interfaces (GUIs) and other programs on the PC that communicate with the LaunchPad.Figure 6 shows the pathway of the backchannel UART. The backchannel UART is the UART on eUSCI_A0.
On the host side, a virtual COM port for the application backchannel UART is generated when the LaunchPad enumerates on the host. You can use any PC application that interfaces with COM ports, including terminal applications like Hyperterminal or Docklight, to open this port and communicate with the target application. You need to identify the COM port for the backchannel. On Windows PCs, Device Manager can assist.
Figure 7. Application Backchannel UART in Device Manager
The backchannel UART is the MSP Application UART1 port. In this case, Figure 7 shows COM13, but this port can vary from one host PC to the next. After you identify the correct COM port, configure it in your host application according to its documentation. You can then open the port and begin communication to it from the host.On the target MSP430FR2433 side, the backchannel is connected to the eUSCI_A0 module. The eZ-FET has a configurable baud rate; therefore, it is important that the PC application configures the baud rate to be the same as what is configured on the eUSCI_A0.
2.2.5 Optional Features
2.2.5.1 SupercapacitorA through-hole component footprint is available on the board and allows user to populate a supercapacitorto power the system without any external power. The recommended part is the Panasonic EEC-S0HD224H 220 mF (0.22 F) supercapacitor and can be purchased from major electronic componentdistributers.
NOTE: A supercapacitor is not included in the kit and must be supplied by the user.
Using the onboard jumper headers, the supercapacitor can configured in the following ways: charging, using (direct connection to 3V3 rail), or disconnected. For more details on these use modes and how to use them, see Section 2.3.
Hardware www.ti.com
10 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2.3 PowerThe board was designed to accommodate various powering methods, including through the onboard eZ-FET as well as from external or BoosterPack power. Figure 8 shows power from the ez-FET and power from external source through header J5 or the BoosterPack module.
Figure 8. MSP-EXP430FR2433 Power Block Diagram
2.3.1
2.3.2
eZ-FET USB PowerThe most common power-supply scenario is from USB through the eZ-FET debugger. This provides 5-V power from the USB and also regulates this power rail to 3.3 V for eZ-FET operation and 3.3 V to the target side of the LaunchPad. Power from the eZ-FET is controlled by jumper J101. For 3.3 V, make sure that a jumper is connected across the J101 3V3 terminal.
BoosterPack and External Power SupplyHeader J5 is present on the board to supply external power directly. It is important to comply with the device voltage operation specifications when supplying external power. The MSP430FR2433 has an operating range of 1.8 V to 3.6 V. More information can be found in the MSP430FR2433 Mixed-Signal Microcontroller data sheet.
www.ti.com Hardware
11SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2.3.3 Supercap (C6)If the supercapacitor is populated, it can be used to evaluate the ultra-low power feature of theMSP430FR2433 target device. See how long you can run your application on the supercap alone.
NOTE: A supercapacitor is not included in the kit and must be supplied by the user.
Figure 9 shows charging the supercap and powering directly from it.
Figure 9. MSP-EXP430FR2433 Supercap Power Block Diagram
2.3.3.1 Charging the SupercapThe supercapacitor can be charged when the EVM is plugged into the PC or when the board is externallypowered. During charging, set J4 to the “Charge” setting, this adds in a current limiting resistor forcharging.
To charge the supercap, power must be coming from the eZ-FET debug probe, external power throughJ5, or a BoosterPack module powering through J1. Allow two to three minutes for the supercap to charge(time may vary depending on initial charge of the supercap and your power source) to full VCC.
2.3.3.2 Using the SupercapAfter charging of the supercapacitor, you can move the J4 jumper to the Use setting and then unplugpower. This connects the supercapacitor to the 3V3 rail without the charging resistor in between. At thispoint, the LaunchPad kit is being powered completely by the C6 supercapacitor.
For lowest power operation, make sure to disconnect the J101 jumpers so that the eZ-FET is not alsopowered by the C6 supercap.
2.3.3.3 Disabling the SupercapThe supercapacitor can be completely decoupled from the board by removing the J4 jumper. Hanging thisjumper off only one pin can prevent losing the jumper.
Hardware www.ti.com
12 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
2.4 Measure Current Draw of the MSP430 MCUTo measure the current draw of the MSP430FR2433 using a multimeter, use the 3V3 jumper on the J101jumper isolation block. The current measured includes the target device and any current drawn throughthe BoosterPack headers.
To measure ultra-low power, follow these steps:1. Remove the 3V3 jumper in the J101 isolation block, and attach an ammeter across this jumper.2. Consider the effect that the backchannel UART and any circuitry attached to the MSP430FR2433 may
have on current draw. Consider disconnecting these at the isolation jumper block, or at least considertheir current sinking and sourcing capability in the final measurement.
3. Make sure there are no floating inputs/outputs (I/Os) on the MSP430FR2433. These causeunnecessary extra current draw. Every I/O should either be driven out or, if it is an input, should bepulled or driven to a high or low level.
4. Begin target execution.5. Measure the current. Keep in mind that if the current levels are fluctuating, it may be difficult to get a
stable measurement. It is easier to measure quiescent states.
EnergyTrace can also be used to compare various current profiles and better optimize your energyperformance!
2.5 ClockingThe MSP-EXP430FR2433 provides external clocks in addition to the internal clocks in the device.• Q1: 32-kHz Epson crystal (FC-135R) 12.5-pF crystal, part number: X1A0001410014
The 32-kHz crystal allows for lower LPM sleep currents than do the other low-frequency clock sources.Therefore, the presence of the crystal allows the full range of low-power modes to be used.
By default, the crystal is not connected to the MSP430FR2433 because the target pins are multiplexedwith 2 BoosterPack header pins. 0-Ω resistors R4 and R5 need to be removed, while R2 and R3 must beshorted across, to connect the external crystal to the MSP430FR2433. See the onboard crystal selectionresistors silkscreen for how to configure the resistors to select between the crystal or the BoosterPackpins.
The internal clocks in the device default to the following configuration:• MCLK: DCO 1 MHz• SMCLK: DCO 1 MHz• ACLK: REFO 32.768 kHz
For more information about configuring internal clocks and using the external oscillators, see the MSP430FR4xx and MSP430FR2xx Family User's Guide.
2.6 Using the eZ-FET Debug Probe With a Different TargetThe eZ-FET debug probe on the LaunchPad can interface to most MSP430 derivative devices, not just the onboard MSP430FR2433 target device.To do this, disconnect every jumper in the isolation jumper block. This is necessary, because the debug probe cannot connect to more than one target at a time over the Spy-Bi-Wire (SBW) connection.Next, make sure the target board has proper connections for SBW. To be compatible with SBW, the capacitor on RST/SBWTDIO cannot be greater than 2.2 nF. The documentation for designing MSP430 JTAG interface circuitry is the MSP430 Hardware Tools User's Guide.Finally, wire together these signals from the debug probe side of the isolation jumper block to the target hardware:• 5 V (if 5 V is needed)• 3.3 V• GND• SBWTDIO
www.ti.com Hardware
13SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
• SBWTCK• TXD (if the UART backchannel is to be used)• RXD (if the UART backchannel is to be used)
This wiring can be done either with jumper wires or by designing the board with a connector that plugs intothe isolation jumper block.
2.7 BoosterPack PinoutThe LaunchPad kit adheres to the 20-pin LaunchPad pinout standard. A standard was created to aidcompatibility between LaunchPad kits and BoosterPack modules across the TI ecosystem.
While most BoosterPack modules are compliant with the standard, some are not. The MSP-EXP430FR2433 LaunchPad kit is compatible with all 20-pin BoosterPack modules that are compliant withthe standard. If the reseller or owner of the BoosterPack module does not explicitly indicate compatibilitywith the MSP-EXP430FR2433 LaunchPad development kit, compare the schematic of the candidateBoosterPack module with the LaunchPad kit to ensure compatibility. Keep in mind that sometimesconflicts can be resolved by changing the MSP430FR2433 device pin function configuration in software.
Figure 10. BoosterPack Checker Tool
To check the compatibility of your desired BoosterPack modules for your design, with a LaunchPad kit of your choice, you can use the BoosterPack Checker tool. This allows you to select any LaunchPad kit that TI offers and determine its compatibility with any number of BoosterPack modules. You can also add your own BoosterPack module to check its compatibility as you prototype that next design.Figure 11 shows the 20-pin pinout of the MSP430FR2433 LaunchPad development kit.The inner side of the dashed line shows some of the software selectable functions on each pin, including the functions that conform to the standard. However, each pin may have other functionalities that can be configured by the software. See the MSP430FR2433 data sheet for more details on individual pin functions.
Hardware www.ti.com
14 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
Figure 11. LaunchPad Kit to BoosterPack Module Connector Pinout
2.8 Design Files
2.8.1
2.8.2
HardwareSection 6 shows the schematics. All design files including schematics, layout, bill of materials (BOM), Gerber files, and documentation are available on the MSP-EXP430FR2433 design files download page.
SoftwareAll design files including TI-TXT object-code firmware images, software example projects, and documentation are available on the MSP-EXP430FR2433 design files download page.
2.9 Hardware Change logTable 3 lists the revision history of the MSP-EXP430FR2433 hardware.
Table 3. Hardware Change Log
PCB Revision DescriptionRev 1.0 Initial release
3 Software ExamplesFour software examples are included with the MSP430FR2433 LaunchPad development kit (see Table 4), which can be found in the MSP430FR2433 LaunchPad development kit download page and are also available inside the MSPWare software.
Table 4. Software Examples
Demo Name BoosterPackRequired Description More Details
OutOfBox_FR2433 None The out-of-box demo preprogrammed on the LaunchPad kit from thefactory. Demonstrates features of MSP430FR2433 device Section 3.1
BlinkLED_FR2433 None Blinks an LED on the LaunchPad kit at a fixed interval Section 3.2
To use any of the software examples with the LaunchPad development kit, you must have an integrated development environment (IDE) that supports the MSP430FR2433 device (see Table 5).
Table 5. IDE Minimum Requirements for MSP-EXP430FR2433
Code Composer Studio IDE IAR Embedded Workbench for TexasInstruments MSP430 IDEVersion 6.1.3 or later Version 6.30 or later
www.ti.com Software Examples
15SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
For more details on how to get started quickly, and where to download the latest CCS and IAR IDEs, see Section 4.
3.1 Out-of-Box Software Example
3.1.1
This section describes the functionality and structure of the out-of-box software that is preloaded on the EVM.
The Out-of-Box demo for the MSP-EXP430FR2433 LaunchPad development kit demonstrates how to setup a periodic temperature data logger, by using a ring-buffer inside the FRAM memory of the MSP430FR2433 MCU. The demo also implements a real-time temperature sensor.
Source File StructureThe project is split into multiple files (see Table 6). This makes it easier to navigate and reuse parts of it for other projects.
Table 6. Source File and Folders
Name Descriptionmain.c Out-of-Box demo main function
FRAMLogMode.c Contains functions for the FRAM data logging modeLiveTempMode.c Contains function for the live temperature streaming modeLibrary: driverlib Device driver library
Library: fram-utilities Contains the CTPL and NVS software libraries from the FRAM UtilitiesLibrary: iqmathlib Fixed Point Math Library for MSP
Library: jsmn Third-party library for parsing JSON formatted strings
3.1.2
3.1.3
OverviewAn online cloud GUI (MSP-EXP430FR2433 OOB GUI) can be used to download this demo to your board and visualize the temperature data. A serial terminal can also be used to display the data being sent from the demo to the PC (application UART settings: 115200, 8, 1, n).Upon powering up the Out-of-Box demo, the green LED2 lights up for 1 second, and then the board enters FRAM data logging mode to measure and record the internal temperature of the MSP430FR2433 MCU every 5 seconds.By default after power up, the LaunchPad development kit enters the FRAM data logging mode. At any time, press the S1 and S2 buttons simultaneously to switch between the live temperature mode and the FRAM data logging mode.
FRAM Data Logging ModeThis mode shows the FRAM data logging capabilities of the MSP430FR2433. After starting this mode, the LaunchPad wake up from LPM3.5 approximately every 5 seconds (indicated by short red LED1 blink) to log temperature values. Data are stored into a ring buffer located in the FRAM memory. When the ring buffer fills up to its capacity, the oldest temperature data is discarded and replaced with the newest data.• Press the left button S1 to transfer all data stored inside the ring buffer to the PC.• Press the right button S1 to clear all data and return to an empty ring buffer.• The compute through power loss (CTPL) and nonvolatile storage (NVS) libraries from the FRAM
Utilities are used in this demo to simplify the code to setup this simple data logging application.
3.1.4 Live Temperature ModeIn this mode, the LaunchPad kit repeatedly measures the internal temperature of the MSP430FR2433MCU and transfers the data to the PC through UART.
Software Examples www.ti.com
16 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
The application also keeps track of a temperature threshold in this mode (default is 25°C), and when anew temperature data is acquired, it is compared against the threshold. If measured temperature is belowthe threshold, the green LED2 illuminates, and if the measured temperature is above the threshold, thered LED1 illuminates.
Independently pressing S1 or S2 increases or decreases, respectively, the temperature threshold in thismode. The further the recorded temperature is from the threshold, the brighter the corresponding LEDsilluminate.
The user can influence the temperature of the device by blowing hot or cold air and observing thechanges in the user LED brightness or see data changes on the GUI.
3.2 Blink LED Example
3.2.1
This very simple software example shows how to software toggle a GPIO to blink an LED on the LaunchPad kit.
Source File StructureThe project is split into multiple files (see Table 7). This makes it easier to navigate and reuse parts of it for other projects.
Table 7. Source File and Folders
Name Descriptionmain.c The Blink LED main function
Library: Driverlib Device driver library
The main code simply uses the MSP430 Driver Library to halt the watchdog timer and to configure andtoggle the P1.0 GPIO pin connected to the LED inside a software loop.
4 Resources
4.1 Integrated Development EnvironmentsAlthough the source files can be viewed with any text editor, more can be done with the projects if theyare opened with a development environment like Code Composer Studio IDE and IAR EmbeddedWorkbench IDE.
4.1.1 TI Cloud Development ToolsTI's Cloud-based software development tools provide instant access to MSPWare content and a web-based IDE.
4.1.1.1 TI Resource Explorer CloudTI Resource Explorer Cloud provides a web interface for browsing examples, libraries and documentation found in MSPWare without having to download files to your local drive (see Figure 12).Visit TI Resource Explorer Cloud now at dev.ti.com.
www.ti.com Resources
17SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
Figure 12. TI Resource Explorer Cloud
4.1.1.2 Code Composer Studio CloudCode Composer Studio Cloud (CCS Cloud) is a web-based IDE that enables you to quickly create, edit, build and debug applications for your LaunchPad development kit. No need to download and install large software packages, simply connect your LaunchPad development kit and begin. You can choose to select from a large variety of examples in MSPWare software and Energia or develop your own application. CCS Cloud supports debug features such as execution control, breakpoints and viewing variables.For a full comparison between CCS Cloud and CCS Desktop, visit the TI Cloud Tools page.Visit Code Composer Studio Cloud now at dev.ti.com.
Figure 13. CCS Cloud
Resources www.ti.com
18 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
4.1.2 Code Composer Studio IDECode Composer Studio Desktop is a professional integrated development environment that supports TI's Microcontroller and Embedded Processors portfolio. Code Composer Studio comprises a suite of tools used to develop and debug embedded applications. It includes an optimizing C/C++ compiler, source code editor, project build environment, debugger, profiler, and many other features.Learn more about CCS and download it at www.ti.com/tool/ccstudio.CCS v7.0.0 or higher is required. When CCS has been launched, and a workspace directory chosen, use Project>Import Existing CCS Eclipse Project. Direct it to the desired demo's project directory that contains main.c.
Figure 14. Directing the Project>Import Function to the Demo Project
Selecting the \CCS subdirectory also works. The CCS-specific files are located there.When you click OK, CCS should recognize the project and allow you to import it. The indication that CCS has found it is that the project appears in the box shown in Figure 15, and it has a checkmark to the left of it.
www.ti.com Resources
19SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
4.1.3
Figure 15. When CCS Has Found the Project
Sometimes CCS finds the project but does not show a checkmark; this might mean that your workspace already has a project by that name. You can resolve this by renaming or deleting that project. (Even if you do not see it in the CCS workspace, be sure to check the workspace directory on the file system.)
IAR Embedded Workbench for Texas Instruments 430IAR Embedded Workbench for MSP430 is another very powerful integrated development environment that allows you to develop and manage complete embedded application projects. It integrates the IAR C/C++ Compiler, IAR Assembler, IAR ILINK Linker, editor, project manager, command line build utility, and IAR C-SPY® Debugger.Learn more about IAR Embedded Workbench for MSP430 and download it atsupp.iar.com/Download/SW/?item=EW430-EVAL.
IAR 6.30 or higher is required. To open the demo in IAR, click File>Open>Workspace…, and browse to the *.eww workspace file inside the \IAR subdirectory of the desired demo. All workspace information is contained within this file.The subdirectory also has an *.ewp project file. This file can be opened into an existing workspace byclicking Project>Add-Existing-Project….
Although the software examples have all of the code required to run them, IAR users may download andinstall MSPWare, which contains MSP430 libraries and the TI Resource Explorer. These are alreadyincluded in a CCS installation (unless the user selected otherwise).
4.2 LaunchPad WebsitesMore information about the LaunchPad development kit, supported BoosterPack plug-in modules, andavailable resources can be found at:• MSP-EXP430FR2433 Tool Folder: Resources specific to this particular LaunchPad development kit• TI's LaunchPad portal: Information about all LaunchPad development kits from TI
Resources www.ti.com
20 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
4.3 MSPWare and TI Resource ExplorerTI Resource Explorer is a tool integrated into CCS that allows you to browse through available design resources. TI Resource Explorer helps you quickly find what you need inside packages including MSPWare, ControlSuite, TivaWare, and more. TI Resource Explorer is well organized to find everything that you need quickly, and you can import software projects into your workspace in one click.TI Resource Explorer Cloud is one of the TI Cloud Development tools and is tightly integrated with CCS Cloud. See Section 4.1.1 for more information.MSPWare is a collection of code examples, software libraries, data sheets, and other design resources for all MSP devices delivered in a convenient package – essentially everything developers need to become MSP experts.In addition to providing a complete collection of existing MSP design resources, MSPWare also includes a high-level API called MSP Driver Library. This library makes it easy to program MSP hardware. For more information, see www.ti.com/tool/mspware.
Figure 16. Using TI Resource Explorer to Browse MSP-EXP430FR2433 in MSPWare
Inside TI Resource Explorer, these examples and many more can be found, and easily imported into CCSwith one click.
4.4 FRAM Utilities
4.4.1
4.4.2
The TI FRAM Utilities is a collection of embedded software utilities that leverage the ultra-low-power and virtually unlimited write endurance of FRAM. The utilities are available for MSP430FRxx FRAM microcontrollers and provide example code to help start application development.
Compute Through Power Loss (CTPL)CTPL is a utility API set that enables ease of use with LPMx.5 low-power modes and a powerful shutdown mode that allows an application to save and restore critical system components when a power loss is detected.
Nonvolatile Storage (NVS)The NVS library makes handling of nonvolatile data easy and robust against intermittent power loss or asynchronous device resets. To keep data storage constant, the nonvolatile storage library contains functions that store data in a way that is ensures recovery of the last valid entry without data corruption.
www.ti.com Resources
21SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
4.5 MSP430FR2433 MCU
4.5.1 Device DocumentationAt some point, you will probably want more information about the MSP430FR2433 device. For every MSP device, the documentation is organized as shown in Table 8.
Table 8. How MSP Device Documentation is Organized
Document For MSP430FR2433 DescriptionDevice familyuser's guide
MSP430FR4xx and MSP430FR2xx Family User's Guide
Architectural information about the device, including all modules andperipherals such as clocks, timers, ADC, and so on.
Device-specificdata sheet
MSP430FR2433 Mixed-Signal Microcontroller data sheet Device-specific information and all parametric information for this device
4.5.2
4.5.3
MSP430FR2433 Code ExamplesMSP430FR243x, MSP430FR253x, MSP430FR263x Code Examples is a set of simple C examples that demonstrate how to use the entire set of peripherals on the MSP4302433 MCU, including serial communication, ADC10, Timer, and others, through direct register access. Every MSP derivative has a set of these code examples. When starting a new project or adding a new peripheral, these examples serve as a great starting point.
MSP430 Application Notes and TI DesignsMany application notes can be found at www.ti.com/msp430, along with TI Designs with practical design examples and topics.
4.6 Community Resources
4.6.1
4.6.2
5
TI E2E™ CommunitySearch the forums at e2e.ti.com. If you cannot find your answer, post your question to the community.
Community at LargeMany online communities focus on the LaunchPad development kits – for example, www.43oh.com. You can find additional tools, resources, and support from these communities.
FAQQ: I can't get the backchannel UART to connect. What's wrong?A: Check the following:• See Section 5.8.2 of the MSP Debuggers User's Guide for supported baud rates when using the
eZ-FET.• Do the baud-rate settings in the terminal application on the host PC and the eUSCI match?• Are the appropriate jumpers in place on the isolation jumper block?• Probe on RXD and send data from the host. If you don't see data, it might be a problem on the host
side.• Probe on TXD while sending data from the MSP. If you don't see data, it might be a configuration
problem with the eUSCI module.• Consider the use of the hardware flow control lines (especially for higher baud rates). Q: The MSP G2 LaunchPad kit has a socket that allows me change the target device. Why doesn'tthis LaunchPad kit use one?A: The target device on this LaunchPad kit does not come in the dual in-line package. Sockets for theavailable device package are too expensive for the target price of this LaunchPad kit.
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
1 3
7/27/2017
LaunchPad_eZFET_1.4.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
MSP-EXP430FR2433Project Title:Designed for: Public Release
Assembly Variant: [No Variations]
!Texas Instruments 2017
Drawn By:Engineer: Eric Chen
Texas Instruments and/or its licensors do not warra nt the accuracy or completeness of this specificati on or any information contained therein. Texas Inst ruments and/or its licensors do notwarrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or itslicensors do not warrant that the design is product ion worthy. You should completely validate and testyour design implementation to confirm the system fu nctionality for your application.
Version control disabledSVN Rev:MCU024Number: Rev: 1.0
TID #: N/AOrderable: EVM_orderable
IO11
IO22
GND3
IO34
IO45
VCC6
IC102
TPD4E004DRYR
33kR123
27
R104
27
R103
1.0MR106
10pFC110
10pFC111
0.1 F!C105
IN1
OUT3
NC4
NC5
EN6
2
GND
IC101
TLV70033DSET
TP101
TP102
TP103
TP104
TP105
TP106
TP107
TP108
TP109
EZ_GNDEZFET_TEST
EZFET_TDO
EZFET_TDI
EZFET_TMS
EZFET_TCK
EZFET_RST
EZFET_DCDCRST
EZFET_DCDCTEST
EZFET_DP
EZFET_DM
1.40k
R105
EZFET_PU.0/DP
EZFET_PU.1/DM
EZFET_PUR
EZ_GND EZ_GND EZ_GND
EZ_GND
EZFET_SHIELD
EZFET_SHIELD
EZFET_SHIELD
EZFET_VBUS
EZ_GND
EZ_GND
EZ_GND
EZ_GND
EZ_GND
Change IC101 to adjust target voltage from 2.8V to 3.6VTLV7033:3.3V
USB Interface and Power Supply
P6.0/CB0/A01
P6.1/CB1/A12
P6.2/CB2/A23
P6.3/CB3/A34
P6.4/CB4/A45
P6.5/CB5/A56
P6.6/CB6/A67
P6.7/CB7/A78
P5.0/A8/VREF+/VEREF+9
P5.1/A9/VREF-/VEREF-10
AVCC111
P5.4/XIN12
P5.5/XOUT13
AVSS114
DVCC115
DVSS116
VCORE17
P1.0/TA0CLK/ACLK18
P1.1/TA0.019
P1.2/TA0.120
P1.3/TA0.221
P1.4/TA0.322
P1.5/TA0.423
P1.6/TA1CLK/CBOUT24
P1.7/TA1.025
P2.0/TA1.126
P2.1/TA1.227
P2.2/TA2CLK/SMCLK28
P2.3/TA2.029
P2.4/TA2.130
P2.5/TA2.231
P2.6/RTCCLK/DMAE032
P2.7/UCB0STE/UCA0CLK33
P3.0/UCB0SIMO/UCB0SDA34
P3.1/UCB0SOMI/UCB0SCL35
P3.2/UCB0CLK/UCA0STE36
P3.3/UCA0TXD/UCA0SIMO37
P3.4/UCA0RXD/UCA0SOMI38
DVSS239
DVCC240
P4.0/PM_UCB1STE/PM_UCA1CLK41
P4.1/PM_UCB1SIMO/PM_UCB1SDA42
P4.2/PM_UCB1SOMI/PM_UCB1SCL43
P4.3/PM_UCB1CLK/PM_UCA1STE44
P4.4/PM_UCA1TXD/PM_UCA1SIMO45
P4.5/PM_UCA1RXD/PM_UCA1SOMI46
P4.6/PM_NONE47
P4.7/PM_NONE48
VSSU49
PU.0/DP50
PUR51
PU.1/DM52
VBUS53
VUSB54
V1855
AVSS256
P5.2/XT2IN57
P5.3/XT2OUT58
TEST/SBWTCK59
PJ.0/TDO60
PJ.1/TDI/TCLK61
PJ.2/TMS62
PJ.3/TCK63
RST/NMI/SBWTDIO64
QFN PAD65
MSP101
MSP430F5528IRGCT
0.1 F!C121
0.1 F!C103
0.1 F!C113
0.1 F!C114
EZ_GND EZ_GND EZ_GND
EZ_GND
EZFET_VBUS EZFET_VCC
EZFET_VREF
EZFET_VCC
10 F!C104
EZ_GND
240kR124
150kR125
33pFC123
1000pFC112
47kR109
0.22 F!C102
0.22 F!C107
0.47 F!C101
1
2
3
4 MHzQ101
EZFET_AVBUSEZFET_AVCCOUT2ADC
EZFET_DCDCIO0EZFET_DCDCIO1EZFET_DCDCRSTEZFET_DCDCTEST
EZFET_VBUS
EZ_GND EZ_GND
EZ_GND
EZFET_VUSB
EZFET_V18
EZFET_VBUS
EZ_GND EZ_GND EZ_GND
Red
LED101
Green
LED102
470
R101
390
R102
EZ_GND
EZ_GND
EZFET_LED0EZFET_LED1
EZFET_VCCEN1EZFET_VCCEN2EZFET_DCDCPULSE
EZFET_UARTCTSEZFET_UARTRTS
EZFET_HOSTSDAEZFET_HOSTSCL
EZFET_UARTTXDEZFET_UARTRXD
EZFET_SBWTDIOEZFET_SBWTCKEZFET_NC_TMSC
EZFET_PU.0/DPEZFET_PU.1/DM
EZFET_PUR
EZ_GND
EZFET_TEST
EZFET_TDOEZFET_TDIEZFET_TMSEZFET_TCK
EZFET_RST
EZFET_VCC
EZ_GND
Host MCU for emulation
P1.0/TA0CLK/ACLK/A0/CA01
TEST/SBWTCK10
P2.7/XOUT11
P2.6/XIN/TA0.112
AVSS13
DVSS14
AVCC15
DVCC16
QFN PAD17
P1.1/TA0.0/A1/CA12
P1.2/TA0.1/A2/CA23
P1.3/ADC10CLK/CAOUT/A3/VREF-/VEREF-/CA34
P1.4/SMCLK/TA0.2/A4/VREF+/VEREF+/CA4/TCK5
P1.5/TA0.0/SCLK/A5/CA5/TMS6
P1.6/TA0.1/SDO/SCL/A6/CA6/TDI/TCLK7
P1.7/CAOUT/SDI/SDA/A7/CA7/TDO/TDI8
RST/NMI/SBWTDIO9
MSP102
MSP430G2452IRSA16R
4.7 F!C106
4.7 F!C109
33pFC115
33pFC116
221kR112
221kR113
221kR114
221kR115
221kR121
221kR122
33pFC122
4.7 F!C117
4.7 F!C119
0.1 F!C124
0.1 F!C118
0.1 F!C120
0.1 F!C125
NO11
COM18
IN27
GND6
NO25
COM24
IN13
V+2
IC103
TS5A21366RSER
1
2
3
D101
BAS40-05W,115
1
2
3
D102
BAS40-05W,115
3
1
2
T102BC850CW,115
4.7kR116
4.7kR117
470R120
2.2 H!
L101
EZ_GNDEZ_GND
EZFET_AVCCOUT2ADC
EZFET_VCCOUT
EZ_GND EZ_GND
EZ_GND EZ_GND
EZFET_VCCOUT
EZFET_VCC
EZ_GND EZ_GND3.30kR127
EZFET_AVCCOUT
EZFET_DCDCPULSEEZFET_DCDCIO0EZFET_DCDCIO1EZFET_AVCC
EZFET_DCDCTESTEZFET_DCDCRST
EZFET_VCC
EZFET_VCCOUT
EZ_GND
EZFET_DCDCCAL0EZFET_DCDCCAL2
EZFET_VCCOUT
EZFET_DCDCCAL1
2.20kR126
6.81kR128
820R118
EZFET_VBUS
0R119
EZ_GNDEZ_GND EZ_GND EZ_GND
EZFET_VCCOUT
EZ_GND EZ_GND EZ_GND
EZ_GND
EZFET_VBUSEZFET_VCCEN1
EZFET_VCCEN2
EZFET_VCCOUT
EZFET_VCC
4.70k
R107
EZ_GND
4.70k
R108
EZ_GND
EZ_GND
Software-controlled DCDC converter
Energy measurement method protected under U.S. Pate ntApplication 13/329,073 and subsequent patent applic ations
EZFET_UARTRXDEZFET_UARTTXD
EZFET_VCCTARGET
EZFET_VCCTARGETEZFET_VBUS
EZ_GND GND
TEST/SBWTCKRST/SBWTDIOBCLUART_TXDBCLUART_RXD
3V35V0
TST/SBWTCK
RST/SBWTDIO
BCLUART_RXD
BCLUART_TXD
eZ-FET Target
0.22 F!C126
EZ_GND
10.0
R129
10.0
R130
EZFET_SBWTCK
EZFET_SBWTDIO
1 F!C108
180 ohm
L102
180 ohm
L103
3
1
2
T101DMG1013UW-7
VBUS1
D-2
D+3
ID4
GND5
678
11
109
J102
100pFDNP C127
EZ_GND
Updated: 13 Feb 2017
1 2
3 4
5 6
7 8
9 10
11 12
13 14
eZ
-FE
T
Targ
et
SBWTCKSBWTDIO
RXD>
3.3V5.0VGND
J101
J101: 1-2
SH-J101-1
J101: 3-4
SH-J101-2
J101: 5-6
SH-J101-3
J101: 7-8
SH-J101-4J101: 9-10
SH-J101-5
J101: 11-12
SH-J101-6
J101: 13-14
SH-J101-7
EZFET_HOSTSCLEZFET_HOSTSDA
Copyright © 2016, Texas Instruments Incorporated
Schematics www.ti.com
22 SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
6 Schematics
Figure 17. Schematics (1 of 2)
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
2 3
7/26/2017
LaunchPad_TargetDevice.SchDoc
Sheet Title:
Size:
Mod. Date:
File:Sheet: of
B http://www.ti.comContact: http://www.ti.com/support
MSP-EXP430FR2433Project Title:Designed for: Public Release
Assembly Variant: [No Variations]
!Texas Instruments 2017
Drawn By:Engineer: Eric Chen
Texas Instruments and/or its licensors do not warra nt the accuracy or completeness of this specificati on or any information contained therein. Texas Inst ruments and/or its licensors do notwarrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or itslicensors do not warrant that the design is product ion worthy. You should completely validate and testyour design implementation to confirm the system fu nctionality for your application.
Version control disabledSVN Rev:MCU024Number: Rev: 1.0
TID #: N/AOrderable: EVM_orderable
DVCC24
DVSS23
DVSS18
P1.0/UCB0STE/TA0CLK/A0/VEREF+7
P1.1/UCB0CLK/TA0.1/A18
P1.2/UCB0SIMO/UCB0SDA/TA0.2/A2/VEREF-9
P1.3/UCB0SOMI/UCB0SCL/MCLK/A310
P1.4/UCA0TXD/UCA0SIMO/TA1.2/TCK/A4/VREF+3
P1.5/UCA0RXD/UCA0SOMI/TA1.1/TMS/A54
P1.6/UCA0CLK/TA1CLK/TDI/TCLK/A65
P1.7/UCA0STE/SMCLK/TDO/A76
P2.0/XOUT21
P2.1/XIN22
P2.2/ACLK11
P2.313
P2.4/UCA1CLK15
P2.5/UCA1RXD/UCA1SOMI16
P2.6/UCA1TXD/UCA1SIMO17
P2.719
P3.012
P3.1/UCA1STE14
P3.220
PAD25
RST/NMI/SBWTDIO1
TEST/SBWTCK2
MSP1
MSP430FR2433IRGER
RST SBWTDIO
SBWTCKTST/SBWTCK
RST/SBWTDIOP2.0P2.1P2.2P2.3P2.4P2.5P2.6P2.7
P1.0P1.1P1.2P1.3P1.4P1.5P1.6P1.7
P3.0P3.1P3.2
3V3
GND
34
12
S1
3 4
1 2
S2
3 4
1 2
S3
GND GND
GNDGND
GND GND
47.0kR1
1000pFC1
GND
3V3
RST
SW1
SW2
1 2
32.768kHz
Q1
12pFC2
12pFC3
GNDGND
0.1 F!C4
10 F!C5
3V3
GND
+3.3V1
Analog_In2
LP_UART_RX3
LP_UART_TX4
GPIO !5
Analog In6
SPI_CLK7
GPIO !8
I2C_SCL9
I2C_SDA10
J1
GPIO !11
SPI_CS/GPIO !12
SPI_CS/GPIO !13
SPI_MISO14
SPI_MOSI15
RST16
GPIO17
GPIO !18
PWM/GPIO !19
GND20
J2
GNDGND
5V01
2
3
J5 3V31
2
3
J6
GND
3V3
1
2
J101
2
J11
470R6
392R7
RedLED1
GreenLED2
GND GND
LEDs
P1.0 P1.1
B0_SDAB0_SCL
LED1LED2
BCLUART_TXD
BCLUART_RXD
BCL_TXDBCL_RXD
P1.6P1.7
A7
A7
SW1
SW2
A6
A6
P1.5BCL_RXDP1.4BCL_TXD
P1.0A0
P2.4
A1 CLK
A1 CLK
RST
A1 MOSIA1 MISO
A1 MISOA1 MOSI
TA0.1P1.1
P3.1
P3.2
P2.6P2.5
P2.2
TA0.1 A1 CS
5V21
GND22
J35V0
GND
A1 CS
A0
LED1 LED2
0 DNP
R2
0 DNP
R3XIN
XOUT
P2.0_BP
P2.1_BP0
R4
0
R5
P2.0_BPP2.1_BPP1.3
P1.2B0_SCLB0_SDA
P2.7SW2
Super Capacitor
3V3
220000 F!DNPC6
GND
22
R8
1 2 3
J4
Use ChargeJumper Right Position 2-3Jumper Left Position 1-2
Connect jumper here
when discharging the
capacitor to bypass
resistor R8 and
connect to 3V3
Connect jumper here
when charging the
capacitor to use
current limiting
resistor R8
Bypass/DisconnectJumper not connected
When jumper is not in the
"Charge" or "Use" position,
the capacitor is not
connected (bypassed).
We recommend hanging
Hang off single pin
the jumper from one pin so
it does not get lost
J10: 1-2
SH-J10
J11: 1-2
SH-J11
DNP, J4: 2
SH-J4
XIN
XO
UT
Copyright © 2016, Texas Instruments Incorporated
www.ti.com Schematics
23SLAU739–October 2017 Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)
Figure 18. Schematics (2 of 2)
STANDARD TERMS FOR EVALUATION MODULES1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or
documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordancewith the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are notfinished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. Forclarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditionsset forth herein but rather shall be subject to the applicable terms that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or productionsystem.
2 Limited Warranty and Related Remedies/Disclaimers:2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License
Agreement.2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused byneglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that havebeen altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specificationsor instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality controltechniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.
2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or creditUser's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warrantyperiod to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair orreplace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall bewarranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) daywarranty period.
3 Regulatory Notices:3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or softwareassociated with the kit to determine whether to incorporate such items in a finished product and software developers to writesoftware applications for use with the end product. This kit is not a finished product and when assembled may not be resold orotherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the conditionthat this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit mustoperate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTIONThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate the equipment.
FCC Interference Statement for Class A EVM devicesNOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required tocorrect the interference at his own expense.
FCC Interference Statement for Class B EVM devicesNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or moreof the following measures:
• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247
Concerning EVMs Including Radio Transmitters:This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including interference that maycause undesired operation of the device.
Concernant les EVMs avec appareils radio:Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationest autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doitaccepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna typeand its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary forsuccessful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna typeslisted in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibitedfor use with this device.
Concernant les EVMs avec antennes détachablesConformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type etd'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillageradioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotroperayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Leprésent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans lemanuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antennenon inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation del'émetteur
3.3 Japan
3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に輸入される評価用キット、ボードについては、次のところをご覧ください。 http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certifiedby TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow theinstructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule forEnforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect toEVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japanwith respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please notethat if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けていないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。2. 実験局の免許を取得後ご使用いただく。3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社東京都新宿区西新宿6丁目24番1号西新宿三井ビル
3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/ /www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
3.4 European Union3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):
This is a class A product intended for use in environments other than domestic environments that are connected to alow-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment thisproduct may cause radio interference in which case the user may be required to take adequate measures.
4 EVM Use Restrictions and Warnings:4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety informationrelated to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable andcustomary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to inputand output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, orproperty damage. If there are questions concerning performance ratings and specifications, User should contact a TIfield representative prior to connecting interface electronics including input power and intended loads. Any loads appliedoutside of the specified output range may also result in unintended and/or inaccurate operation and/or possiblepermanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting anyload to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuitcomponents may have elevated case temperatures. These components include but are not limited to linear regulators,switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using theinformation in the associated documentation. When working with the EVM, please be aware that the EVM may becomevery warm.
4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with thedangers and application risks associated with handling electrical mechanical components, systems, and subsystems.User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronicand/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safelylimit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility andliability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors ordesignees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes allresponsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility andliability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and localrequirements.
5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurateas possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites asaccurate, complete, reliable, current, or error-free.
6. Disclaimers:6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY MATERIALS PROVIDED WITH THE EVM (INCLUDING, BUT NOT
LIMITED TO, REFERENCE DESIGNS AND THE DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALLFAULTS." TI DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUTNOT LIMITED TO ANY EPIDEMIC FAILURE WARRANTY OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESSFOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY THIRD PARTY PATENTS, COPYRIGHTS, TRADESECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS SHALL BECONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY OTHER INDUSTRIAL ORINTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD PARTY, TO USE THEEVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY INVENTION, DISCOVERY ORIMPROVEMENT, REGARDLESS OF WHEN MADE, CONCEIVED OR ACQUIRED.
7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITSLICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANYHANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS. THIS OBLIGATION SHALL APPLYWHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY OTHER LEGALTHEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8. Limitations on Damages and Liability:8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESETERMS OR THE USE OF THE EVMS , REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OFSUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, COST OF REMOVAL ORREINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, RETESTING,OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS, LOSS OF SAVINGS, LOSS OFUSE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL BE BROUGHT AGAINST TIMORE THAN TWELVE (12) MONTHS AFTER THE EVENT THAT GAVE RISE TO THE CAUSE OF ACTION HASOCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY USE OF AN EVM PROVIDEDHEREUNDER, INCLUDING FROM ANY WARRANTY, INDEMITY OR OTHER OBLIGATION ARISING OUT OF OR INCONNECTION WITH THESE TERMS, , EXCEED THE TOTAL AMOUNT PAID TO TI BY USER FOR THE PARTICULAREVM(S) AT ISSUE DURING THE PRIOR TWELVE (12) MONTHS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARECLAIMED. THE EXISTENCE OF MORE THAN ONE CLAIM SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not ina resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicableorder, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating tothese terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive reliefin any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2017, Texas Instruments Incorporated
IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES
Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who aredeveloping applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms ofthis Notice.TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TIproducts, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,enhancements, improvements and other changes to its TI Resources.You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing yourapplications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. Yourepresent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures thatmight cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, youwill thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted anytesting other than that specifically described in the published documentation for a particular TI Resource.You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that includethe TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TOANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTYRIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationregarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty orendorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES ORREPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TOACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUALPROPERTY RIGHTS.TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOTLIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IFDESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH ORARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THEPOSSIBILITY OF SUCH DAMAGES.You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your non-compliance with the terms and provisions of this Notice.This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services. These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2017, Texas Instruments Incorporated
MSP430FR2433 LaunchPad™ Development Kit (MSP‑EXP430FR2433)1 Getting Started1.1 Introduction1.2 Key Features1.3 What's Included1.3.1 Kit Contents1.3.2 Software Examples
1.4 First Steps: Out-of-Box Experience1.4.1 Connecting to the Computer1.4.2 Running the Out-of-Box Demo
1.5 Next Steps: Looking Into the Provided Code
2 Hardware2.1 Block Diagram2.2 Hardware Features2.2.1 MSP430FR2433 MCU2.2.2 eZ-FET Onboard Debug Probe With EnergyTrace Technology2.2.3 Debug Probe Connection: Isolation Jumper Block2.2.4 Application (or Backchannel) UART2.2.5 Optional Features2.2.5.1 Supercapacitor
2.3 Power2.3.1 eZ-FET USB Power2.3.2 BoosterPack and External Power Supply2.3.3 Supercap (C6)2.3.3.1 Charging the Supercap2.3.3.2 Using the Supercap2.3.3.3 Disabling the Supercap
2.4 Measure Current Draw of the MSP430 MCU2.5 Clocking2.6 Using the eZ-FET Debug Probe With a Different Target2.7 BoosterPack Pinout2.8 Design Files2.8.1 Hardware2.8.2 Software
2.9 Hardware Change log
3 Software Examples3.1 Out-of-Box Software Example3.1.1 Source File Structure3.1.2 Overview3.1.3 FRAM Data Logging Mode3.1.4 Live Temperature Mode
3.2 Blink LED Example3.2.1 Source File Structure
4 Resources4.1 Integrated Development Environments4.1.1 TI Cloud Development Tools4.1.1.1 TI Resource Explorer Cloud4.1.1.2 Code Composer Studio Cloud
4.1.2 Code Composer Studio IDE4.1.3 IAR Embedded Workbench for Texas Instruments 430
4.2 LaunchPad Websites4.3 MSPWare and TI Resource Explorer4.4 FRAM Utilities4.4.1 Compute Through Power Loss (CTPL)4.4.2 Nonvolatile Storage (NVS)
4.5 MSP430FR2433 MCU4.5.1 Device Documentation4.5.2 MSP430FR2433 Code Examples4.5.3 MSP430 Application Notes and TI Designs
4.6 Community Resources4.6.1 TI E2E Community4.6.2 Community at Large
5 FAQ6 Schematics
Important Notice