Post on 30-Jul-2018
transcript
MWS®
DESIGN FEATURES
• UL Listed under Standard 183 for make or break under load.
• Meets requirements of Article 604 of the National Electrical Code.
• MWS components assembled with 12 AWG/10 AWG conductors rated at 20 amperes with full size ground wire.
• Copper conductors are THHN insulated wire rated 90°C.
• Galvanized steel exterior with integral keying for voltage and amperage.
• Valox 365 constructed contact housings are approved for environmental air plenums.
• Cable end supplied with 1/2" connector with locknut and 6" pre-stripped leads.
• DC cable allows you to easily supply power to other system units such as j-boxes, receptacles or fixtures.
DC
DROP CABLE
Modular Wiring System
MWS, Modular Wiring Systems, provide low cost installation of branch circuit wiring for lighting and power. Using modular components that plug together, MWS can be installed in a fraction of the time of hardwiring. Plus, MWS offers the advantage of relocating fixtures and outlets in future renovations.
The MWS Drop Cable (DC) supplies power to out of system units that are wall mounted or ceiling mounted.
MWS Drop cables may be plugged into the last fixture cable (FC) or from a Splitter (SP) anywhere within the system.
DESCRIPTION
Cable Unit Standard
Length Wt. Qty./Carton
5' 2.0 lbs. 12
9' 3.0 lbs. 9
11' 3.5 lbs. 8
SHIPPING DATA
S
YSTEMS
C
E RT I F I E
D
Top
Side
4-3/8"[112mm]
1-7/8"[47mm]
5/8"[16mm]
DIMENSIONAL DATA
Drop Cable (DC)Supplies power to out of system units. (Fixtures, J-boxes, etc.).
Typical MWS Wiring System Application shown utilizing Drop Cable (DC).
Consult MWS Installation, Application and Specification Manual for additional comprehensive system information.
Extender Cable Splitter orCircuit T
Extender Cable
Drop Cable
Junction Box or any Out of System Unit supplied by others.
SYSTEM VIEW (not to scale)
MWS AUTOCAD DRAFTINGMWS offers AutoCAD drafting to layout MWS, providing the contractor with additional benefits.
MWS design layout time is reduced.
Bills of material are computer-generated guaranteeing accuracy.
MWS drawing symbols and detailsstandardized.
Layouts are available on CD or e-mail.
To utilize this service and for additionalinformation, contact the MWS Sales Department (888) 487-4887.
All electrical boxes, conduit, connections and switches by others.
Install dust covers on unused open ends.
Scale is exaggerated on fixtures and MWS system applications.
ADF0318512015-01-15 09:36:13
SAMPLE NUMBER: 2 7 D C 1 2 /2 G 1 1
ComponentDC=DropCable
DC
Voltage12=120V20=208V24=240V27=277V34=347V48=480V
Conductors and Size10/2G=#10, 2 Conductors Plus Ground10/3G=#10, 3 Conductors Plus Ground10/4G=#10, 4 Conductors Plus Ground12/2G=#12, 2 Conductors Plus Ground12/3G=#12, 3 Conductors Plus Ground12/4G=#12, 4 Conductors Plus Ground
Cable Length (Feet)05=5'09=9'11=11'15=15'
Options2N=2 Neutral (1)
NOTES: (1)12/4G and 10/4G only.Specifications & dimensions subject to change without notice. Consult your Cooper Lighting Representativefor availability and ordering information.
ORDERING INFORMATION
Catalog # Type
Date
Project
Comments
Prepared by
Eaton1000 Eaton BoulevardCleveland, OH 44122United StatesEaton.com
Specifications and dimensions subject to change without notice.
Eaton’s Cooper Lighting Business 1121 Highway 74 SouthPeachtree City, GA 30269P: 770-486-4800www.cooperlighting.com