Post on 20-Aug-2019
transcript
NB-203M
MINI-CELL
N-BIOTEK CO2 Incubators
Advantages
of N-BIOTEK CO2 INCUBATOR
• 6 sides Direct heating
• Dry Wall and Air Jacket
• 3 Temperature Sensor Control
• Dual Beam IR CO2 Sensor
• 125℃ Dry Hot Air Decontamination
• Natural Humidification from Water Tray
Common FEATURE of CO2 Incubator
Stacked NB-203 & 203XL NB-203XXL
BASIC FEATURES
Air Jacket -6 side direct heating
Control Panel
Magnetic Door Seal
Glass door
Door Latch
Outer door
Outer door heater -Prevent condensation
Ventilation Fan
Glass door heater -Prevent condensation
Stainless Steel Shelve -Perforated to improve uniformity
Inner door seal -Airtight to prevent Co2 leakage
Water pan -Heated by 6 sides direct heating for humidity
NB-203
BASIC FEATURE
Back of CO2 Incubator
Control Panel of CO2 Incubator
Co2 Gas inlet Serial label
Overheating Safety
Power Cord
Spare Fuse
Excellent Temperature Control
Six sided direct heating
The advantage of 6 side direct heating
- Precise Temperature Control(Fast Warm up)
- Quick Recovery Time after opening door
3 Temperature Sensors
- For controlling Heaters in 3 Segment
- No Condensation on Glass Door
- Maximizing Uniformity
Natural And Force Air and Humidity Circulation
- Efficient Heating Element Arrangement.
- Horizontal Laminar Airflow System
- Excellent Uniformity of CO2, Temp, Humidity
Integrated Air Circulation System using both Natural and Force Convection
Heat Preservation in Air Jacket Between Chamber and Insulation
Air Circulation Diagram
Blow Fan
Detail of CO2 Incubator 1. Humidity Control – Natural Humidification(Water tray, Basic Function) This is a good way to maintain high humidity in chamber in order to protect FBS, MEM(kind of medium) dried. 2. Alarm (Basic Function) Alarm on when : 1) Temp : Over ±1 ℃ 2) CO2 Density: Over ±1% than Set point. High and Low Density 3) 30 Seconds After Door open 3. Calibration by One Touch Button (Basic Function) Difference Temp and CO2 Density between Display and Real Value Calibration is done by Pushing CALIBRATION button 4. Over Temp safety (Basic Function) OVER HEAT Limit DIAL
6. Split Inner Glass Door (Optional)
Option of CO2 Incubator
5 Divided Door For NB-203
5. ACCESS PORT (Optional) To use this like outlet port 30mm Hole located on left side of incubator, which is able to apply various additional equipment or to probe inside of Chamber.
Benefits of Split Door 1. Effective Gas Consumption
2. Maintain consistent climactic condition
3. Reduce Gas Consumption
4. Minimizes any changes during door open
5. Fast Recovery Time
6. Reduce the risk of contamination
7. Maintain easy access to samples
6 Divided Door For NB-203XL
Option of CO2 Incubator 7. Cooling Option (Peltier) -5℃ from room temperature but the lowest temperature is up to 20℃
8. Customized Option: UV Lamp and HEPA filter
HEPA FILTER UV LAMP
Six sided direct heating HOT AIR is useful to destroy bacteria and germ and other
factors causing a contamination
3 Hours for Decontamination (125℃)
4 ~ 5 Hours to cool down to 37℃
Automatic Re-set at Temp & CO₂
Safety Door Lock
Option of CO2 Incubator 9. Hot Air Decontamination
Option of CO2 Incubator 10. O2 Control (Tri-gas control)
O₂ Function On/Off Key O₂ Adjustment Key
O₂ Set-up Button
O₂ Display LED window
Pilot Lamp for O₂ Injection Control (when O₂ injects into chamber,
Lamp is ON for 0%~22%)
Back of CO2/O2 Incubator
Control Panel of CO2/O2 Incubator
● NOTIFICATION: To create hypoxic condition(lower O₂ than atmosphere) N2 must be supplied.
● NOTIFICATION: To create hyperoxia condition(higher O₂ than atmosphere) O₂ must be supplied.
Option of CO2 Incubator 10. O2 Control (Tri-gas control)
Zirconia O2 Sensor
N2 Gas Control Valve O2 Gas Control Valve CO2 IR Sensor
No need to remove the Oxygen Sensor during Hot Air Sterilization because O₂ sensor is installed outside chamber through a pipe like above.
Pipes connecting between chamber and sensor to chamber
Stacking Kit & Caster Option
Caster Base Tray Stacking Kit
Copper Chamber
NBIOTEK customize chamber with oxidizing copper / copper-plated chamber for enhanced contamination protection.
MiniCell™ - 16L CO2 Incubator
Portable MINI CO2 Incubator
NB-203M
Features of MiniCell™
Portable MINI CO2 Incubator
• 16L Chamber, 6.8kg light to carry • Portable with carrying handle • Available size to use in work-station or Clean bench • Forced Air Circulation by Fan • 2 Stainless Steel Shelves as Standard (Max. 3 shelves) • Natural Humidification by water tray • Power Plug & Car Jack
Access Port of MiniCell™
Option of Portable MINI CO2 Incubator
• Ø12mm(Dia) Access Port with Silicon Stopper
NB-203XXL(Max Cell™)
850L Large Capacity CO2 Incubator
850L, 185cm height
6 Sides direct heating system
2 Divided Glass doors
3 Standard Shelves (Max. 15 ea.)
UV Sterilization even during cell culture
Protect heat loss by Magnetic Sealing
Water Tray for Natural Humidity
Chamber made of SUS304
Dry wall and air jacket
Dual BEAM IR CO₂ sensor
Various options
FEATURES of Large CO2 Incubator
Air Jacket -6 side direct heating
Control Panel
Magnetic Door Seal
Glass door Door Latch
Outer door
Outer door heater -Prevent condensation
Air Circulation Fan
Glass door heater -Prevent condensation
Inner door seal -Airtight to prevent air & CO₂ leakage
Water pan -Heated by bottom heater for Humidification
Door lock
Stainless Steel Shelve -3 shelves are standard -Perforated to improve uniformity
NB-203XXL
CO2 Incubator with Shaker and Roller
NB-206CXL
NB-203QMS
NB-203QR NB-203QS
NB-206CL
CO2 Incubator with Roller
179L CO2 Incubator with Built-in Roller
↑NB-203QR
Roller is placed on the bottom of Chamber
Adherent and suspension Cell culture
are simultaneously conducted at an incubator
Standard Accessories
– 4 Bottles (Φ100mm~120mm) & One Shelve
Controlling roller at outside control panel
CO2 Incubator with Shaker
CO2 Incubator with Built-in Shaker Mini Shaker(NB-101S) is built in.
BLDC motor allows incubator LOW vibration, LOW particle occurrence, LOW noise
Adherent and suspension Cell culture can be simultaneously conducted in an incubator
Controlling internal shaker at outside control panel
↑ 179L, NB-203QS ↑47L, NB-203QMS ↑ 179L, NB-206CL
NB-206CXL, 650Liter NB-206CXXL, 850Liter
Large Capacity CO2 Incubator Shaker
AniCell™ Instruction
① ②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
1) Shaker control panel
2) Incubator control panel
3) 3 Divided glass door
4) Outer door
5) Shaker (NB-101M)
6) Pullout shaker platform
7) Humidity tray
8) Magnetic door seal
9) Door latch
10) Air Circulation fan
11) Lockable caster
12) CO2 Input port
13) 4-20mA Analogue output port
14) Safety switch
15) Access port
⑫ ⑬ ⑭
⑮
Inner Door Open
Back of AniCell
Outer Door Open Actual Figure of AniCell
Detail of AniCell™
Features of AniCell™
Slide-out Shaker Platform Platform of each shakers can be pulled out for loading flasks on each shakers efficiently
3 Mountable Medium Shaker (NB-101M) in One Incubator
Features of AniCell™
• Door Latch with built-in magnetic 1. To avoid injury, when user stand up
from sitting to handle middle & bottom shakers.
2. Holding full three doors when taking shaker out or cleaning in chamber
3 Split Inner Glass Doors
• Advantages of split doors 1. Minimization for loss of Temp &
CO2& Humidity 2. Lower Affection to Shaker to Shaker 3. Auto Stop when door open 4. Full observation without loss
Features of AniCell™
Natural Humidification Large Water Tray is placed on the bottom of chamber. Bottom Heater warms up the water then natural humidification occur.
Features of AniCell™
Ceiling in Chamber
UV Light
Circulation Fan above Ceiling
UV lamp & Anti-Bacterial Filter
Features of AniCell™
HEPA Filter
Efficient Arrangement of
Heating Element For Natural Convection
Air Jacket
1. Forming Air Jacket
between Insulation and Chamber
2. Enhanced Heat Preservation
3. Helping Recovery Time faster
4. Longer Heat Preservation in power failure
5. Dense Heating Element for Fast Heat-Up
Features of AniCell™
CO₂, Temperature, UV, Alarm control and Humidity display is on Right Panel
Control Panel of AniCell™
Temp. Set Key
Co2 charging signal
Heat-operating Signal
Alarm Mute
Co2 Set Key Calibration Set Key
Humidity Display UV ON/OFF
ALARM ON/OFF
RPM/TIME selection key
RPM/TIME SET key
START/STOP key
Each 3 Shakers can controlled individually and each Pilot Lamp displays running of each shakers
Fast heat-up of AniCell™
Fast Detection of CO2 Density
Display Real Density
Fast Recovery & Stable Maintains
Co2 Density Control by IR Sensor
Shaker of AniCell™
NB-206CXL NB-206CXXL
BLDC motor allows incubator
LOW vibration, LOW particle occurrence, LOW noise
Moisture resistant mechanism
Holder platform
Belt disconnection
Heat by friction
Disadvantages of using Belt connection shaker Higher Particle & Vibration & Noise from belt connection
Frictional heat occurred by Belt Working
Short life time caused by high humidity in CO2 incubator
(No water proof construction)
Regular Lubrication on Belt Connection is required
Shaker of AniCell™
BLDC Magnetic Induction Direct Drive
Stable Shaking !
LOW vibration LOW Noise LOW heat LOW Particle! No Belt! No replacement! Longer Life Time Plate type and low height: Low Vibration
Shaker of AniCell™
Shaker Control outside chamber No Need to Open the door
For Shaker Operation
Epoxy Coated Coil Plate makes
Moisture-Resistant Mechanism
Durable Motor Mechanism & User Friendly Design Moisture Free ! Easy to Control !
Shaker of AniCell™
Stain Resistant Interior
Inner chamber & all shakers are
constructed with stainless steel SUS304
SUS304 is resistant to rust formation in
high humidity condition
Material of AniCell™
OR
Various holders & Sticky mat
* Optimum performance for maximum allowance can be obtained at 150rpm.
Thank You!!