NAICS / SIC / PSC (FSC): 334220 / 3663 / 5985 HTS & ECCN: … · 2018-01-30 · NAICS / SIC /...

transcript

NAICS / SIC / PSC(FSC): 334220 / 3663 / 5985. S. Huynh, 1/29/2018

MATTERWAVESAntenna Technology

M M1 of 30

CAGE Code: 80CX3 | ITAR: Registered

MATTERWAVES ANTENNA TECHNOLOGY . 2461 W 205TH STE B103 . Torrance, CA 90501 . Tel: (310) 251-1102 . Fax: (310) 782-7430 . antennas@matterwaves.com . http://www.matterwaves.com

2461 W 205Th ST STE B103Torrance, California 90501Phone: 310-251-1102Fax: 310-782-7430http://www.matterwaves.comAntenna@Matterwaves.com

Rapid Customization, Fabrication & Production of High End L1/L2/L5 GPS, Glonass, GNSS, CRPA, L-Band, Inmarsat, Iridium

Thuraya, Globalstar, Beidou, VHF/UHF, L/S/C/Ku-Band Antennas forSatellite, Avionics, Ground, Marine, and Deep-Sea Applications.

Small Disadvantaged Women Owned Antenna CompanyS-Corporation: Incorporated in CaliforniaCorporate ID: C4069838DUNS: 069526517TIN/EIN/FEIN (Fed Tax ID): 823039862SEIN (State Tax ID): 008880163State Sale Permit: SR AS 103-191435 City Business License: BL-LIC-036341 CAGE Code: 80CX3 NAICS / SIC / PSC (FSC): 334220 / 3663 / 5985 HTS & ECCN: 8529104000 & 7A994 / 5A991.g ITAR: Registered

Facility: 2000 sqft with Option for Quick ExpansionCapability: 500 Antennas/WeekWorking Hour (Monday-Friday): 7:30 am – 8:30 pm

M M3 of 30

Building/Office LayoutFront Office/Lobby (1 of 3)

M M4 of 30

Building/Office LayoutFront Office/Lobby (2 of 3)

M M5 of 30

Building/Office LayoutFront Office & Kitchen Area (3 of 3)

M M6 of 30

Building/Office LayoutConference Room

M M7 of 30

Building/Office LayoutSales/Design Office

M M8 of 30

Building/Office LayoutOperation Room

M M9 of 30

Building/Office LayoutProduction, Parts & Inventory Lead Desks

M M10 of 30

Building/Office LayoutParts & Inventory (1 of 2)

M M11 of 30

Building/Office LayoutParts & Inventory (2 of 2)

M M12 of 30

Building/Office LayoutAssembly, Production and Test Area (1 of 9)

M M13 of 30

M M14 of 30

M M15 of 30

M M16 of 30

M M17 of 30

M M18 of 30

M M19 of 30

M M20 of 30

M M21 of 30

Building/Office LayoutLunch Room

M M22 of 30

Building/Office LayoutOut Door Lunch & Break Area

M M23 of 30

Matterwaves Antenna Products

Satellite/Avionics/Ground/Marine/Deep-Sea Telecommunication Antennas:• RA1/RA2 DAGR GPS Antennas• 2, 3, 4, 5, 7, 8,16-Element CRPA GPS and GNSS Antennas• GPS, Link-16, L, S, C-Band for Mortar & Guided Munition Applications• Active/Passive L1 and L1/L2 GPS/Glonass/Beidou/Galileo/QZSS Antennas • Combined GPS/Glonass/L-Band Antennas• Iridium Antennas• Inmarsat/Thuraya Antennas• Combined Iridium/Inmarsat/Thuraya/GPS Flat/Blade/Tower Antennas• Globalstar Antennas• Combined Globalstar/GPS Antennas• XM/Iridium/GPS Antennas• GSM/GPS Antennas• UHF/GSM/Wi-Fi/Iridium/GPS 10k-psi-Deep-Sea Antennas• 4G LTE Omni/Direction Antennas• Broad band UHF, L, S, C, Ku-band Video/Data Link Antennas• VHF/UHF Patch/Rod/Blade Antennas• Ku-Band Antennas• DF Blade Antennas• Broad Band Helix, Back-Cavity/Conical Spiral, Horn, Log-periodic Antennas

• Microwave Devices• Power Combiners/Dividers, Beam Forming Networks• Filters, Diplexers • Low Noise Amplifiers

E-mail antenna@matterwaves.com to Request for Particular Antenna Product Brochures

M M24 of 30

Matterwaves Antennas are Designed for belowSatellite, Avionics, Ground, Marine, and Deep-Sea Platforms

M M25 of 30

Matterwaves Antenna ProductDesign/Production/QA/Test Flow

We Stay Focus on Design/Assembly/Test & Subcontract Out Below Works to Local Vendors:• Radome Machining and Injection Molding• Antenna Housing/Baseplate Machining• Connector and Cable Harness• LNA/PCB Pick/Place/Fab• Metal/Foam/Gasket Stamping

ENGINEERING

MANUFACTURE

SUB-CONTRACT

RADOME CONNECTORS CIRCUIT BOARDFABRICATION

INDUSTRIALMATERIAL

AVAILABILITY/CAPABILITY

MANUFACTURETOLERANCE

ELECTRICAL/MECHANICAL DESIGN/

SIMULATION

MACHINED PARTS

SPECIFICATION

AT LEAST 3VENDERS

OTHER PARTS

ACCEPTANCE TESTPROCEDURE (ATP)

FABRICATIONDRAWING/SPEC

QUALITY CONTROL/DOCUMENTATION

SIMPLE DESIGNLESS PARTS

EASY ASSEMBLY

SHIPPING

Schedule control, producibilty, low risk, Cost effectiveness

INCOMING PAR TS

ElectricalTEST

ASSEMBLY

QUALIFIEDPRODUCTS

QUALIFICATIONTEST

MAJOR DESIGN CHANGE/NEW PRODUCTS or

FEED BACK

PROTOTYPE

QUALITY CONTROL/DOCUMENTATION

EXISTING DESIGNPROVEN HARWARE

CABLEASSEMBLY

M M26 of 30

I. Standards, Mil-STD, and Specifications for Design/Fab/Test:1) TSO: C-144, C-139, C-169a 2) Environmental: RTCA/DO-160D, TSO C144, DO-228, MIL-STD-810; SAE J1455 (Automotive), MIL-STD-1472F (DoD)3) Lightning: DO-160F, Direct Effects , Section 234) Electrical: RTCA/DO-160D, TSO C144, DO-228/DO-254, Mil-STD-461F, MIL-STD-810, MIL-HDBK-5400 5) CE: EMC Directive 89/336/EEC (European Union) & 47CFR, Part 15, Subpart B (FCC)6) EMI, EMC / Emission: DO-160D/E, DO-228, MIL-STD-810G, MIL-STD-464C / EN 55022: 2006 / U.S. 47 CFR PART 15, SUBPART B7) Immunity: EUROPEAN STANDARD EN 55024: 1998, Amendment A2: 20038) Hazardous / REACH Compliance: NAS411-1, SVHC by ECHAII. Standards, Mil-STD, Specifications & Q-Notes for Design/Fab/Material/Process:1) Stainless Steel Material: Mil-STD-889B, DFARS 252-225-7009/DFARS 225.872-1.2) Screws: Mil-STD-889B, DFARS 252-225-7009/DFARS 225.872-1.3) Connectors/Adapters/Cables: Mil-PRF-39012/55339, IPC JSTD-001 Rev E, DFARS 252-225-7009/DFARS 225.872-1.4) Pick/Place and Soldering: JESD-625, ANSI/ESD-S20.20, IPC JSTD-001 Rev E, IPC-A-610 Class 3.5) Printed Circuit Board (PCB): IPC-A-600G, JESD-625, ANSI/ESD-S20.20, IPC JSTD-001 Rev E, IPC-A-610 Class 3.8) Solder: No Pure Tin (<3% Pb) Solder unless otherwise specified in the PO for RoHS. JESD-625, ANSI/ESD-S20.20, IPC JSTD-001 Rev E.9) ESD: IPC JSTD-001 Rev E.10) Aluminum Material: Mil-STD-889B, Al6061-T6/ASTM-B-221.11) Chem Film: Mil-C-5541F Type I Class 3 for Yellow. Type II Class 3 for Clear (ROHS). MIL-A-8625F Type II & III (Hard Anodize).12) Nickel plating (EN): MIL-AMS2404/AMS2404 Class 4. MIL-C-26074E, AMS-2404C, AMS-2405B, AMS-2433B13) Gold Plating: Mil-G-45204, Mil-DTL-45204; Type II, Gr C, I and III, Gr A ; ASTM B488; AMS 2422; SCGPS 06024 14) Zinc Plating: ASTM B633, Type I, II, III (clear, yellow and black); AMS 2402515) Painting / Identification: FED-STD-595B, MIL-PRF-85582E, MIL-PRF-85285E / MIL-STD-130N-116) Inspection / FAI / Safety: MIL-I-45208A / (AS/EN/SJAC 9102) / RCC-324-0117) Equipment/Tools Calibration: ISO17025:2005 & ANSI/NCSLZ540-1.

III. Q-Notes for Vendors:1) Shelf Life: Adhesives, Solder, RTV, Epoxies, Glues, Thread Locker, Sealant and Adhesives on Gaskets must meet at least 75% remaining shelf life upon receipt.2) FOD: All parts have to meet FOD requirements, must be cleaned, free of dirt, oil, or any lubricant compound before shipping.3) Packaging: Scratch-Dent-Damaged Proof at 1ft Box-Drop. Part #, Item #, PO #, and Date are required on Big Vertical Label outside shipping boxes.4) ESD: LNA’s shipped to Matterwaves must be in resealable ESD bags with desiccant Moisture Absorbers/Indicators. ESD warning sticker must be visible on the outer box.5) PCB: Shipped to Matterwaves must be in resealable ESD bags with desiccant Moisture Absorbers/Indicators inside. 6) Nickel Plating: Housings must be handled at all times using gloves and be shipped to Matterwaves in resealable ESD bags with desiccant Moisture Absorbers/Indicators.7) Painting: All antenna assemblies prior to painting must be cleaned with acetone on all surfaces and be handled using gloves at all times. Must comply with the

requirements of correct color code, paint/primer type, thickness, and reference specification on http://www.Matterwaves.com/documents/Paint_Spec.pdf. Antenna painted parts shipped to Matterwaves must be in individual anti-static bubble bags.

8) Changes: In Facility/Processing/Equipment/Procedures/Locations/Material must need to notify Matterwaves in advance for review and approval.9) Counterfeit: New and authentic materials. Authorized sources. Traceability to applicable authorized sources. Subcontractors and suppliers requirement flow down.10) Ultem Material: Machined/molded parts must be shipped with CofA Cert.11) Conflict Minerals: (3TG: Tin, Tantalum, Tungsten, & Gold) must not be coming from Democratic Republic of Congo & adjoining countries and should be DRC

conflict-free. Must comply with the requirements of FAR Clause 52.222-50, Combating Trafficking in Persons.

Specifications , Mil-STD & Q-notes Used forDesign, Fab, Test, Material & Process

M M27 of 30

- CAD System for Drawings•AutoCAD •Solidwork•Gerber

- S-Parameter testing (Return Loss, VSWR, Insertion Loss, Isolation, Gain, etc.)-ENA5063A

- Radiation Pattern Test (Gain, Axial Ratio, Phase Center, Amp/Phase Tracking, Side lobe, F/B Ratio, etc…)

- Planar, Cylindrical, Spherical Near/Far Field System is Capable of Measuring Different Types of Antennas.

- Anechoic Chamber Size: (30ftx30ftx30ft), and (12ftx12ftx12ft)- Frequency Range: 250 MHz to 60 GHz- Testable Antenna’s Size: 3’x3’x3’- Pattern: Narrow Beam, Broad Beam, Fan Beam, and Omni-directional

- Radiation Pattern Data Formats (Hard copies, PDF, BMP, or ASCII format)- 2-D Rectangular/Polar Plots- 2-D/3-D Contours Plots- Co/X-Polarization of Amp/Phase Data-Matrix - Percentage of Gain Coverage.- Percentage of Axial Ratio Coverage.

Equipment & Testing Capability

M M28 of 30

Antenna Test Range(Partner with http://www.allwavecorp.com Nearby 5mins Away)

Radiation Pattern Test (Gain, Axial Ratio, Phase Center, Amp/Phase Tracking, Side lobe, F/B Ratio, etc…)- Planar, Cylindrical, Spherical Near/Far Field System is Capable of Measuring Different Types of Antennas.- Anechoic Chamber Size: (30ftx30ftx30ft), and (12ftx12ftx12ft)- Frequency Range: 250 MHz to 60 GHz.- Testable Antenna’s Size: 3’x3’x3’.- Pattern: Narrow Beam, Broad Beam, Fan Beam, and Omni-directionalRadiation Pattern Data Formats (Hard copies, PDF, BMP, or ASCII format)- 2-D Rectangular/Polar Plots- 2-D/3-D Contours Plots- Co/X-Polarization of Amp/Phase Data-Matrix - Percentage of Gain Coverage.- Percentage of Axial Ratio Coverage.

M M29 of 30

Environmental Testing (Full QM/FM Testing)

Company Certification Flight Experience

Contact

DNB Engineering, Inc3535 W. Commonwealth Ave Fullerton, CA 92833

A2LA, NVLAP, EU, AS9100, FAA, FCC, TSO-C144RTCA/DO-160D, DO-228MIL-C-5541, MIL-E-5400, MIL-STD-810, MIL-I-45208AMIL-S-901D, MIL-STD-167-1, BRL and RDEC approved, DOD4145.26M, MIL-STD-45662

Yes DNB Engineering, Inc3535 W. Commonwealth Ave Fullerton, CA 92833 Phone: 714-870-7781https://www.dnbenginc.com/

NATIONAL TECHNICAL SYSTEMS 1536 East Valencia Drive Technical Fullerton, California 92831 Systems

A2LA, NVLAP, EU, AS9100, FAA, FCC, TSO-C144RTCA/DO-160D, DO-228MIL-C-5541, MIL-E-5400, MIL-STD-810, MIL-I-45208AMIL-S-901D, MIL-STD-167-1, BRL and RDEC approved, DOD4145.26M, MIL-STD-45662

Yes David GregoryTel: 714-879-6110 Fax: 714-879-6117 http://www.ntscorp.com

We are currently teamed up with the following environmental laboratories to perform full QM testing. The followingcompanies are local in our area. Our Quality control and engineering staff will constantly monitor the test. All tests suchas humidity, temperature vibration, shock, etc., are performed according to MIL-STD-810G, RTCA/DO-160D/E, MIL-STD-461/462/464, Direct Lightning, TSO-C139/144, and/or customer specifications.

1 of 2

Son (Sean) Huy Huynh U.S. Citizen Redondo Beach, Ca 90278. USA Held DOD Clearance Phone: 310-251-1102 DOB: April-30-1964 E-mail: sean.huynh@matterwaves.com

Corporate / Technical Design / Fab / Production / QA / Test Experience https://www.linkedin.com/in/sean-huynh-b57090101/

Co-Founder of Antcom Corporation, An Antenna Products Company in Torrance California, USA. http://www.antcom.com/ Started Antcom from Ground Level up to a $6M Antenna Company. Sold It to Novatel and Continued to Run/Grow It to $12M Company. Specialized in Avionics/Ground/Space/Marine Telecommunication Antenna Products for Military/Commercial Applications. Antenna Products Developed/Certified: http://www.antcom.com/documents/catalogs/Antcom_Antenna_Products.pdf Designed, Negotiated, and Won:

- Many Multi-Year High Volume Passive/Active L1/L2 FRPA GPS Antenna Contracts for Military Ground Applications. - Many Multi-Year High Volume FRPA/CRPA GPS Antenna Contracts for Guided Munitions, Helicopters/Airplanes Applications.

- Repeated VHF/UHF/L/S/C/Ku-Band Blade Antenna Contracts for Avionics, Ground, and Marine Applications. 15 Years Experience in VP/General Manager & 20 Years Experience in VP of Eng/R&D. All in Antennas/Microwave-RF. 20 Years Experience in Marketing/Sale, R&D, Engineering, Production, QA, Test, TSO Certification, ISO-9001. All in Antennas/RF. 28 Years Experience in Antenna/Microwave CKT Design, AutoCAD, Simulation, Test, Equipment, Near/Far-Field Antenna Testing, Material/Industrial Engineering, Mil-STD-810E/DO-160 Testing, TSO Cert, Radomes, Injection Molding, Enclosures, Coating, Painting, Adhesives, Bonding, Foams, Gaskets, O-rings, Screws, Connectors, Cables, Wires, Metal, Ceramics, PCB, Pick/Place, Electronics Parts.

Dec-2017 - Present : President at Matterwaves Antenna Technology in Torrance, CA, USA. Rapid Customization, Fabrication & Production of High End L1/L2/L5 GPS, Glonass, GNSS, CRPA, L-Band, Inmarsat, Iridium, Thuraya, Globalstar, Beidou, VHF/UHF, L/S/C/Ku-Band Antennas for Video/Data Link, Satellite, Avionic, Ground, Marine, and Deep Sea Telecommunication Applications. 1997 – 2017 (20 yrs): Co-Founder at Antcom Corporation in Torrance, CA, USA. VP of Engineering and R&D (2012 – Sep-2017): Fully in Charge of Electrical/Mechanical Engineering, R&D, QA Departments. Provide Key Decision Making to Sales/Marketing/Tech Support/Production. Solve Problems and Lead.

Design/Develop/Production of High End L1/L2/L5 GPS, Glonass, GNSS, CRPA, L-Band, Inmarsat, Iridium, Thuraya, Globalstar, Beidou, Compass, IRIM, XM, Sirius Antennas for Satellite Telecommunication Applications; VHF/UHF, L/S/C/Ku-Band Antennas for Video/Data Link Applications; UHF, L/S/C-Band Amplifiers.

VP and General Manager (1997 - 2012): Fully in Charge of Antenna Products of the Company from Marketing, Sales, Customer Supports, Engineering, Production, Product Development, Inventory, Quality Control, Certification, Budgeting, Human Resource. Design/Develop/Production of High End L1/L2/L5 GPS, Glonass, GNSS, CRPA, L-Band, Inmarsat, Iridium, Thuraya, Globalstar, Beidou, Compass, IRIM, XM, Sirius Antennas for Satellite Telecommunication Applications; UHF, L/S/C/Ku-Band Antennas for Video/Data Link Applications; UHF, L/S/C-Band Power Divider/Amplifiers.

1994 - 1997 (3 yrs): TRW (Northrop Grumman) in Redondo Beach, CA, USA. Section Head in Antenna Department (1996 - 1997):

Supervise a group of 6 Members of Technical Staffs Work on Government Classified Projects Work on the Satellite Up-Link Phased Array Antenna for Teledesic Design/Develop (2-12) GHz 1024-Way Power Combiner for Classified Projects Design Fixed/Mobile CD-Radio Antennas for Digital Radio Applications. Work on Point-to-Point/Multi-Point Communication Antenna for Winstar Proposal

Senior MTS in Antenna Department (1994 - 1996): Microwave/Antenna Hardware Design/Simulation/Product Development Software Simulation for 60 GHz Beam Waveguide Antenna System Responsible Design Engineer for Odyssey Multi-beam Satellite Communication Beam-Forming Network Responsible Design Engineer for Odyssey Handset Antenna and Fixed Terminal Antennas Responsible Design Engineer for Ku/Ka-Band TDRSS Polarizer/TWC Systems

1989 - 1994 (5 yrs): Sensor Systems, Inc. in Chatsworth, CA, USA Supervisor of R&D Electrical Antenna Department (1992 - 1994) / Antenna Project Engineer (1989 - 1992):

Technical Proposals and Product Development Design, Fabrication, Testing, and Tuning Active and Passive Prototype Antennas, RF & Microwave Circuits for Avionics, Fixed & Mobile Satellite Communication Systems Software Development & Production Support Antennas Designed: Active L1/L2 GPS Microstrip, Active Differential GPS/SatCom, Microstrip Low-Gain L-Band SatCom, Planar Array L/Ku-Band SatCom, L-Band SatCom Blade, Microstrip GPS/Glonass, UHF Satcom, TCAS, L-Band/UHF Blade, VHF Blade, Altimeter, Glide-Slope, Log-Periodic, Horns, Backed-Cavity Spirals Cross Dipoles, Phased-Arrays, Hybrids, Radar Augmentation Systems, and Other Antenna Applications RF/Microwave Circuits Designed: Amplifiers, Filters, Diplexers, Switches, Phase-Shifters, Couplers, Power-Dividers Using Lumps, Microstrip, or Stripline Components Work in Frequency Bands: HF, VHF, UHF, L, E/F, S, C, I, J, and Ku Band

2 of 2

EDUCATION: B.S. and M.S. Degree in Electrical Engineering from California State University Northridge, CA, USA, 1989/1993. Majoring in Antennas/Microwave Circuits (Study under Dr. Edmond S. Gillespie)

HONORS, AWARDS, & PATENTS:

• U.S. Patent No. US 9,837,721 B2 “Low Profile Dipole Antenna”. • U.S. Patent No. US 9,257,756 B2, “Dual Band Directive/Reflective Antenna”. • U.S. Patent No. US 9,214,734 B2, “Multi-Quadrifilar Helix Antenna”. • U.S. Patent No. US 05760741, “Beam Forming Network For Multiple-Beam-Feed Sharing Antenna System”. • U.S. Patent No. US 5872549, “Quadrifilar Helix Antenna Feed Network”. • U.S. Patent No. US 06002377, “Low Cost Mobile/Fixed Satellite Telecommunication Antennas”. • U.S. Patent No. US 06040805, “Low Profile Choke Slot Ground Plane for GPS Application”. Special Recognition by Raytheon, Precision Guidance Systems, for Developing small high performance Handheld L1/L2 Helix GPS Antenna for DAGR Program, 2003. Special Recognition, Roll of Honor, by TRW’s Space & Electronics Group for Independent Research and Development of Mobile Communication Antenna Technology, 1996

NAICS / SIC / PSC (FSC): 334220 / 3663 / 5985 HTS & ECCN: … · 2018-01-30 · NAICS / SIC /...

Documents