transcript
- Slide 1
- Slide 2
- Objective of Lecture Apply the almost ideal op amp model in the
following circuits: Inverting Amplifier Noninverting Amplifier
Voltage Follower Summing Amplifier Difference Amplifier Cascaded
Amplifiers
- Slide 3
- Almost Ideal Op Amp Model i 2 = 0 i 1 = 0 Linear Region: When V
+ < v o < V -, v o is determined from the closed loop gain A
v times v 2 as v 1 = v 2 (v d = 0 V). Saturation: When A v v 2 V +,
v o = V +. When A v v 2 V -, v o = V -. Ri = and Ro = 0
- Slide 4
- Example #1: Inverting Amplifier i 2 = 0 i 1 = 0 isis ifif V+ =
15V V- = -10V i
- Slide 5
- Example #1 (cont) i 2 = 0 i 1 = 0 isis ifif V+ = 15V V- = -10V
i
- Slide 6
- Example #1 Closed loop gains are dependent on the values of R1
and Rf. Therefore, you have to calculate the closed loop gain for
each new problem.
- Slide 7
- Example #1 (cont) i 2 = 0 i 1 = 0 isis ifif i vovo
- Slide 8
- Example #1 (cont) Since A V = -10 If Vs = 0V, V0 = -10(0V) = 0V
If Vs = 0.5V, Vo = -10(0.5V) = -5V If Vs = 1V, Vo = -10(1V) = -10V
If Vs = 1.1V, Vo = -10(1.1V) < V -, Vo = -10V If Vs = -1.2V, V0
= -10(-1.2V) = +12V If Vs = -1.51V, Vo = -10(-1.51V) > V +, Vo =
+15V
- Slide 9
- Example #1 (cont) Voltage transfer characteristic Slope of the
voltage transfer characteristic in the linear region is equal to A
V.
- Slide 10
- Example #2: Noninverting Amplifier
- Slide 11
- Example #2 (cont)
- Slide 12
- Slide 13
- Slide 14
- Example #2: Noninverting Amplifier
- Slide 15
- Example #2 (cont) A V = +11 If Vs = 0V, V0 = 11(0V) = 0V If Vs
= 0.5V, Vo = 11(0.5V) = +5.5V If Vs = 1.6V, Vo = 11(1.6V) > V +,
Vo = +15V If Vs = -0.9V, V0 = 11(-0.9V) = -9.9V If Vs = -1.01V, Vo
= 11(-1.01V) > V + Vo = +15V
- Slide 16
- Example #2 (cont) Voltage transfer characteristic Slope of the
voltage transfer characteristic in the linear region is equal to A
V.
- Slide 17
- Example #3: Voltage Follower A voltage follower is a
noninverting amplifier where R f = 0 and R 1 = . V o /V s = 1 +R f
/R 1 = 1 + 0 = 1
- Slide 18
- Example #4: Summing Amplifier A summing amplifier is an
inverting amplifier with multiple inputs. V + = 30V V - =-30V
- Slide 19
- Example #4 (cont) i 2 = 0 v1v1 v2v2 i 1 = 0 iAiA iBiB iCiC ifif
We apply superposition to obtain a relationship between Vo and the
input voltages.
- Slide 20
- Example #4 (cont) A virtual ground
- Slide 21
- Example #4 (cont)
- Slide 22
- Note that the voltages at both nodes of R C are 0V.
- Slide 23
- Example #4 (cont)
- Slide 24
- Slide 25
- Slide 26
- Slide 27
- Example #5: Difference Amplifier
- Slide 28
- Example #5 (cont) i 2 = 0 v1v1 v2v2 i 1 = 0 iAiA iBiB iCiC
ifif
- Slide 29
- Example #5 (cont) i 2 = 0 v1v1 v2v2 i 1 = 0 iAiA iBiB iCiC
ifif
- Slide 30
- Example #5 (cont) i 2 = 0 v1v1 v2v2 i 1 = 0 iAiA iBiB iCiC
ifif
- Slide 31
- Example #5 (cont) iAiA ifif
- Slide 32
- Slide 33
- If R A /R f = R B /R C And if R A = R f
- Slide 34
- Example #6: Cascading Op Amps
- Slide 35
- Example #6 (cont) Treat as two separate amplifier circuits
- Slide 36
- Example #6 (cont) First Circuit Second Circuit
- Slide 37
- Example #6 (cont) It is a noninverting amplifier.
- Slide 38
- Example #6 (cont) It is a inverting amplifier.
- Slide 39
- Example #6 (cont) The gain of the cascaded amplifiers is the
multiplication of the two individial amplifiers
- Slide 40
- Summary The almost ideal op amp model: Ri = i 1 = i 2 = 0A; v 1
= v 2 Ro = 0 No power/voltage loss between the dependent voltage
source and v o. The output voltage is limited by the voltages
applied to the positive and negative rails. V + v o V - This model
can be used to determine the closed loop voltage gain for any op
amp circuit. Superposition can be used to solve for the output of a
summing amplifier. Cascaded op amp circuits can be separated into
individual amplifiers and the overall gain is the multiplication of
the gain of each amplifier.