Post on 18-Mar-2018
transcript
Model : MI12832DO-1
OLED MODULE SPECIFICATION
Revision 1.1 Engineering Date 2012-12-19 Our Reference
MULTI-INNO TECHNOLOGY CO., LTD.
www.multi-inno.com
Approved
Comment
For Customer's Acceptance:
Customer
This module uses ROHS material
This specification may change without prior notice in
order to improve performance or quality. Please contact
Multi-Inno for updated specification and product status
before design for this product or release of this order.
REVISION RECORD REV NO. REV DATE CONTENTS REMARKS
1.0 2009-06-05 Preliminary
P.2 MULTI-INNO TECHNOLOGY CO.,LTD.
Ver 1.1MODULE NO.: MI12832DO-1
1.1 2012-12-19 Update life time
P.3 MULTI-INNO TECHNOLOGY CO.,LTD.
CONTENT � PHYSICAL DATA
� ABSOLUTE MAXIMUM RATINGS
� EXTERNAL DIMENSIONS
� ELECTRICAL CHARACTERISTICS
� RELIABILITY TESTS � OUTGOING QUALITY CONTROL SPECIFICATION � CAUTIONS IN USING OLED MODULE
� TIMING OF POWER SUPPLY
� INTERFACE PIN CONNECTIONS
� ELECTRO-OPTICAL CHARACTERISTICS
Ver 1.1MODULE NO.: MI12832DO-1
PHYSICAL DATA
P.4 MULTI-INNO TECHNOLOGY CO.,LTD.
1
Resolution 128 (H) x 32 (V) Pixel
Duty 1/32 - 3
Active Area 22.384 (W) x 5.584 (H) mm
4
Outline Dimension 30.00 (W) x 11.50 (H) x 1.45 (D) mm
5
Pixel Pitch 0.175 (W) x 0.175 (H) mm
6
Pixel Size 0.159 (W) x 0.159 (H) mm
11 Weight 1.05 g
7
Driver IC SSD1306 -
8
Monochrome -
9
Interface 4-wire SPI - 10
2
Display Mode Passive Matrix OLED -
Display Color (White)
No. Items Specification Unit
2
3
2
2
Ver 1.1MODULE NO.: MI12832DO-1
EXTERNAL DIMENSIONS
P.5 MULTI-INNO TECHNOLOGY CO.,LTD.
2-φ0.8±0.1
CS#
D/C
#
15
C2P
15
CS#
D/C#
0.1±0.03
Contact Side
Contact Side
Notes:
1. Color: W
hite2. D
river IC: SSD
13063. Interface: 4-w
ire SPI4. G
eneral Tolerance: ±0.305. The total thickness (1.55 M
ax) is without polarizer protective film
& rem
ove tape. The actual assem
bled total thickness with above m
aterials should be 1.80 Max.
Active A
rea 0.91"128 x 32 Pixels
3M #1318B
8.4x8x0.063mm
VC
C
VC
OM
H
IREF
SDIN
SCLK
RES#
VD
D
VSS
VBA
T
C2N
C1N
C1P
(Reference M
echnical Design)
(31.6)
(1.61)
(0.86)
Polarizert=0.2m
mR
emove Tape
t=0.15mm
Max
15.3
5.8±0.2
0.9
"A"
Detail "A
"Scale (10:1)
Segment 0
( Colum
n 128 )
Com
mon 31
( Row 1 )
Com
mon 0
( Row 32 )
Segment 127
( Colum
n 1 )
8
VC
C
IREF
SDIN
Symbol
RES#
VD
DV
SS
SCLK
257 6 4 3 1 Pin
VC
OM
H
9101214 13 11
VB
AT
C1P
C1N
C2P
C2N
P0.65x(15-1)=9.1±0.05
W=0.35±0.03
11.25±0.2
22.384 (A/A
)24.384 (V
/A)
25.9 (Polarizer)26.6±0.2 (C
ap Size)30±0.2 (Panel Size)
(2.1)(1.1)
0.35±0.3
5.584 (A/A)7.584 (V/A)
8.8 (Polarizer)11.5±0.2 (Cap Size)11.5±0.2 (Panel Size)
(2.1)(1.1)
0.5±0.5
(1.6)(16.99)
16.3±0.3
1.8±0.3
1.45±0.1
0.1±0.03
(46.3)
1
(0.125)G
lue
5±0.310±0.3
8±0.3
6.8
9.25±0.1
P0.175x128-0.016=22.384
P0.175x32-0.016=5.584
0.1590.175
0.1590.175
Ver 1.1MODULE NO.: MI12832DO-1
ABSOLUTE MAXIMUM RATINGS
P.6 MULTI-INNO TECHNOLOGY CO.,LTD.
Note 1: All the above voltages are on the basis of "VSS = 0V".
Note 2: When this module is used beyond the above absolute maximum ratings, permanent breakage of
Note 3: VCC = 7.25V, Ta = 25 C, 50% Checkerboard.
Software configuration follows Actual Application Example . End of lifetime is specified as 50% of initial brightness reached.The average operating lifetime at
room temperature is estimated by the accelerated operation at high temperature conditions.
2
Items Symbol Min Typ. Max Unit
Supply voltage for logic VDD -0.3 - 4 V
VCC 0 - 11.0 V
Operating temperature TOP -30 - 70 ℃
Storage temperature T -40 - 80 ℃
Life time(120cd/m ) - 25,000 - - hour
Notes
1,2
1,2
-
-
3
Supply voltage for display
ST
the module may occur.Also,for normal operations,it is desirable to use this module under theconditions according to"electro-optical characteristics".If this module is used beyond these co-nditions,malfunctioning of the module can occur and the reliability of the module may deterio-rate.
Humidity - - - 90 %RH -
°
Ver 1.1MODULE NO.: MI12832DO-1
ELECTRICAL CHARACTERISTICS
P.7 MULTI-INNO TECHNOLOGY CO.,LTD.
Note 5: VDD = 2.8V, VCC = 7.25V, 50% Display Area Turn on.
* Software configuration follows Actual Application Example .
◆DC Characteristics
Note 4: Supply Voltage for Display (VCC) are subject to the change of the panel characteristics and the customer’s request.
OUT = 100 A, 3.3MH
Items Symbol Min Typ. Max Unit
Supply voltage for logic VDD 1.65 2.8 3.3 V
Supply voltage for displayVCC
High level input VIH 0.8 x VDD - V
Low level input VIL 0 - 0.2 x VDD V
High level output VOH 0.9 x VDD - V
Low level output VOL 0 - 0.1x VDD V
I
OUT = 100 A, 3.3MHI
OUT = 100 A, 3.3MHI
OUT = 100 A, 3.3MHI
Note 4
Conditions
VDD
VDD
Operating current for V I DD - 180 300 A DD
Operating current for V I CC mA CC Note 5
Sleep mode current for V I DD,SLEEP - 1 5 A DD
A Sleep mode current for VCC I CC,SLEEP
Supply voltage for DC/DC VBAT Internal DC/DC enable
Supply voltage for displayVCC
(Generated by internal DC/DC)
Note 4
(Supplied externally)
(Vcc supplied externally)Operating current for V
I BAT mA BAT Note 5
(Vcc generated by internalDC/DC)
7.0 7.25 7.5 V
3.3 - 4.2 V
7.0 7.25 7.5 V
Note 6
- 4.3 5.4
mA - 6.8 8.5
- 12.6 15.8
mA Note 6 - 18.4 23.0
- 1 5
Note 6: VDD = 2.8V, VCC = 7.25V, 100% Display Area Turn on.
Ver 1.1MODULE NO.: MI12832DO-1
AC Characteristics
P.8 MULTI-INNO TECHNOLOGY CO.,LTD.
Symbol Description Min Max Unittcycle Clock Cycle Time 100 - ns tAS Address Setup Time 15 - ns tAH Address Hold Time 15 - ns tCSS Chip Select Setup Time 20 - ns tCSH Chip Select Hold Time 10 - ns tDSW Write Data Setup Time 15 - ns tDHW Write Data Hold Time 15 - ns tCLKL Clock Low Time 20 - ns tCLKH Clock High Time 20 - ns
tR Rise Time - 40 ns tF Fall Time - 40 ns
* (VDD - VSS = 1.65V to 3.3V, Ta = 25°C)
Ver 1.1MODULE NO.: MI12832DO-1
TIMING OF POWER SUPPLY
P.9 MULTI-INNO TECHNOLOGY CO.,LTD.
2. Power down and Power up Sequence
3. Reset Circuit
1. Commands
Refer to the Technical Manual for the SSD1306
To protect OEL panel and extend the panel life time, the driver IC power up/down routine should include a delay period between high voltage and low voltage power sources during turn on/off. It gives the OEL panel enough time to complete the action of charge and discharge before/after the operation.
4.2.1 Power up Sequence:
1. Power up VDD 2. Send Display off command 3. Initialization 4. Clear Screen 5. Power up VCC6. Delay 100ms
(When VCC is stable) 7. Send Display on command
4.2.2 Power down Sequence:
1. Send Display off command 2. Power down VCC 3. Delay 100ms
(When VCC is reach 0 and panel is completely discharges)
4. Power down VDD
VVDDDD ooffff
VDD
DDiissppllaayy ooffff
VVCCCC ooffff
VSS/Ground
VCC
DDiissppllaayy oonn
VDD
VVDDDD oonn
VVCCCC oonn
VSS/Ground
VCC
When RES# input is low, the chip is initialized with the following status: 1. Display is OFF 2. 128×32 Display Mode 3. Normal segment and display data column and row address mapping (SEG0
mapped to column address 00h and COM0 mapped to row address 00h) 4. Shift register data clear in serial interface 5. Display start line is set at display RAM address 0 6. Column address counter is set at 0 7. Normal scan direction of the COM outputs 8. Contrast control register is set at 7Fh 9. Normal display mode (Equivalent to A4h command)
Ver 1.1MODULE NO.: MI12832DO-1
P.10 MULTI-INNO TECHNOLOGY CO.,LTD.
4. Actual Application Example
Command usage and explanation of an actual example
<Initialization>
* Written Value for Parameters
(1) VCC Supplied Externally (2) VCC Generated by Internal DC/DC Circuit
If the noise is accidentally occurred at the displaying window during the operation, please reset the display in order to recover the display function.
* Set Charge Pump 0x8D, 0x10(1) / 0x14(2)
Set Multiplex Ratio 0xA8, 0x1F
Set Display Offset 0xD3, 0x00
Set Display Start Line 0x40
Set Segment Re-Map 0xA1
Set COM Output Scan Direction 0xC8
Set COM Pins Hardware Configuration 0xDA, 0x02
Set Contrast Control 0x81, 0xCF
* Set Pre-Charge Period0xD9, 0x22(1) / 0xF1(2)
Set VCOMH Deselect Level0xDB, 0x40
Set Normal/Inverse Display0xA6
Set Entire Display On/Off0xA4
Set Display On 0xAF
Clear Screen
Set Display Clock Divide Ratio/Oscillator Frequency 0xD5, 0x80
Set Display Off 0xAE
Ver 1.1MODULE NO.: MI12832DO-1
n ELECTRO-OPTICAL CHARACTERISTICS (Ta=25℃)
P.11 MULTI-INNO TECHNOLOGY CO.,LTD.
Items Symbol Min. Typ. Max. Unit Remark
2 White
Color Coordinate White -Without
Viewing Angle Uniformity ��
* Optical measurement taken at VDD = 2.8V, VCC = 7.25V. Software configuration follows Actual Application Example .
Note : Brightness (L br ) is subject to the change of the panel characteristics and the customer’ s request.
Brightness Lbr 120 150 - cd /m
CIE x 0.26 0.32 0.34 CIE y 0.29 0.33 0.37
Contrast Ratio* Cr - 2000:1 - Darkroom
>160 - - Degree -
Polarizer
INTERFACE PIN CONNECTIONS 1. Block Diagram
1.1 VCC Supplied Externally
Pins connected to MCU interface: CS#, RES#, D/C#, SCLK, and SDIN C1: 1μF C2, C3: 2.2μF R1: 390kΩ, R1 = (Voltage at IREF – VSS) / IREF
Segm
ent 1
27
Segm
ent 0
Com
mon
0
Com
mon
31
~ ~ ~ ~
IREF
VCO
MH
VD
D
R1
RES
#
VSS
SSD1306
C1
VCC
VBA
T
C3
C1P
C1N
C2N
C2P
Active Area 0.91"128 x 32 Pixels
D/C
#
SDIN
SCLK
CS#
C2
Ver 1.1MODULE NO.: MI12832DO-1
P.12 MULTI-INNO TECHNOLOGY CO.,LTD.
1.2 VCC Generated by Internal DC/DC Circuit
Segm
ent 1
27
Segm
ent 0
Com
mon
0
Com
mon
31
~ ~ ~ ~
IREF
VC
OM
H
VD
D
R1
RES
#
C2
VSS
SSD1306
C1
VC
C
VB
AT
C4
C3
C5C6
C1P
C1N
C2N
C2P D/C
#
CS#
SCLK
SDIN
Active Area 0.91"128 x 32 Pixels
Pins connected to MCU interface: CS#, RES#, D/C#, SCLK, and SDIN
C1, C2, C5, C6: 1μF C3, C4: 2.2μF R1: 390kΩ, R1 = (Voltage at IREF – VSS) / IREF
Ver 1.1MODULE NO.: MI12832DO-1
P.13 MULTI-INNO TECHNOLOGY CO.,LTD.
2. Pin Definition
Power Supply
Pin Number Symbol Type Function
7 VDD P PPoowweerr SSuuppppllyy ffoorr LLooggiicc
This is a voltage supply pin. It must be connected toexternal source.
6 VSS P GGrroouunndd ooff OOEELL SSyysstteemm
This is a ground pin. It also acts as a reference for thelogic pins, the OEL driving voltages, and the analogcircuits. It must be connected to external ground.
15 VCC P
PPoowweerr SSuuppppllyy ffoorr OOEELL PPaanneell This is the most positive voltage supply pin of the chip.A stabilization capacitor should be connected betweenthis pin and VSS when the converter is used. It must beconnected to external source when the converter is notused.
13 IREF I CCuurrrreenntt RReeffeerreennccee ffoorr BBrriigghhttnneessss AAddjjuussttmmeenntt
This pin is segment current reference pin. A resistorshould be connected between this pin and VSS. Set thecurrent lower than 12.5
14 VCOMH O VVoollttaaggee OOuuttppuutt HHiigghh LLeevveell ffoorr CCOOMM SSiiggnnaall
This pin is the input pin for the voltage output high levelfor COM signals. A capacitor should be connectebetween this pin and VSS.
5 VBAT P
PPoowweerr SSuuppppllyy ffoorr DDCC//DDCC CCoonnvveerrtteerr CCiirrccuuiitt This is the power supply pin for the internal buffer of theDC/DC voltage converter. It must be connected toexternal source when the converter is used. It should beconnected to VDD when the converter is not used.
3 / 4 1 / 2
C1P / C1N C2P / C2N I
PPoossiittiivvee TTeerrmmiinnaall ooff tthhee FFllyyiinngg IInnvveerrttiinngg CCaappaacciittoorr NNeeggaattiivvee TTeerrmmiinnaall ooff tthhee FFllyyiinngg BBoooosstt CCaappaacciittoorr
The charge-pump capacitors are required between theterminals. They must be floated when the converter isnot used.
9 RES# I PPoowweerr RReesseett ffoorr CCoonnttrroolllleerr aanndd DDrriivveerr
This pin is reset signal input. When the pin is low,initialization of the chip is executed.
8 CS# I CChhiipp SSeelleecctt
This pin is the chip select input. The chip is enabled forMCU communication only when CS# is pulled low.
10 D/C# I
DDaattaa//CCoommmmaanndd CCoonnttrrooll This pin is Data/Command control pin. When the pin ispulled high and serial interface mode is selected, the dataat SDIN is treated as data. When it is pulled low, thedata at SDIN will be transferred to the command register.For detail relationship to MCU interface signals, pleaserefer to the Timing Characteristics Diagrams.
Driver
DC/DC Converter
Interface
Ver 1.1MODULE NO.: MI12832DO-1
P.14 MULTI-INNO TECHNOLOGY CO.,LTD.
Pin Number Symbol Type Function
11 SCLK I SSeerriiaall CClloocckk IInnppuutt SSiiggnnaall
The transmission if information in the bus is following aclock signal. Each transmission of data bit is takenplace during a single clock period of this pin.
12 SDIN I
SSeerriiaall DDaattaa IInnppuutt SSiiggnnaall This pin acts as a communication channel. The inputdata through SDIN are latched at the rising edge of SCLKin the sequence of MSB first and converted to 8-bitparallel data and handled at the rising edge of last serialclock. SDIN is identified to display data or command by D/C#bit data at the rising of first SCLK.
Interface(Continued)
Ver 1.1MODULE NO.: MI12832DO-1
RELIABILITY TESTS Item Condition Criterion
High Temperature Storage
(HTS) 80±2 , 240 hours
High Temperature Operating
(HTO) 70±2 , 240 hours
Low Temperature Storage
(LTS) -40±2 , 240 hours
Low Temperature Operating
(LTO) -30±2 , 240 hours
High Temperature / High Humidity Storage
(HTHHS)
60±3 , 90%±3%RH, 120 hours
Thermal Shock (Non-operation)
(TS)
-40±2 ~ 25 ~ 85±2 (30min) (5min) (30min)
24cycles
1. After testing, the function test is ok.
2. After testing, no addition to the defect.
3. After testing, the change of luminance should be within +/- 50% of initial value.
4. After testing, the change for the mono and area color must be within (+/-0.02, +/-0.02) and for the full color it must be within (+/-0.04, +/-0.04) of initial value based on 1931 CIE coordinates.
5. After testing, the change of total current consumption should be within +/- 50% of initial value.
Vibration (Packing)
10~55~10Hz,amplitude 1.5mm, 1 hour for each direction x, y, z
Drop (Packing)
Height : 1 m, each time for 6 sides, 3 edges, 1 angle
1. One box for each test. 2. No addition to the cosmetic and the electrical defects.
Note 1) For each reliability test, the sample quantity is 3, and only for one test item. 2) The HTHHS test is requested the Pure Water(Resistance 10M ).
P.15 MULTI-INNO TECHNOLOGY CO.,LTD.
Ver 1.1MODULE NO.: MI12832DO-1
OUTGOING QUALITY CONTROL SPECIFICATION
P.16 MULTI-INNO TECHNOLOGY CO.,LTD.
Environment RequiredCustomer’s test & measurement are required to be conducted under the following conditions:
Temperature: 23 ± 5°C Humidity: 55 ± 15 %RH Fluorescent Lamp: 30W Distance between the Panel & Lamp: ≥ 50 cm Distance between the Panel & Eyes of the Inspector: ≥ 30 cm Finger glove (or finger cover) must be worn by the inspector. Inspection table or jig must be anti-electrostatic.
Sampling Plan
Criteria and Acceptable Quality LevelLevel II, Normal Inspection, Single Sampling, MIL-STD-105E
Partition AQL Definition Major 0.65 Defects in Pattern Check (Display On) Minor 1.0 Defects in Cosmetic Check (Display Off)
1.1 Cosmetic Check (Display Off) in Non-Active Area
Check Item Classification Criteria
Panel General Chipping Minor
X > 6 mm (Along with Edge) Y > 1 mm (Perpendicular to edge)
X
Y
X
Y
Ver 1.1MODULE NO.: MI12832DO-1
P.17 MULTI-INNO TECHNOLOGY CO.,LTD.
1.2 Cosmetic Check (Display Off) in Non-Active Area (Continued)
Check Item Classification Criteria
Panel Crack Minor
Any crack is not allowable.
Cupper Exposed
(Even Pin or Film) Minor Not Allowable by Naked Eye Inspection
Film or Trace Damage Minor
Terminal Lead Twist Minor
Not Allowable
Terminal Lead Broken Minor
Not Allowable
Terminal Lead Prober Mark Acceptable
Ver 1.1MODULE NO.: MI12832DO-1
P.18 MULTI-INNO TECHNOLOGY CO.,LTD.
1.3 Cosmetic Check (Display Off) in Non-Active Area (Continued)
Check Item Classification Criteria
Minor
NG if any bent lead cause lead shorting.
Terminal Lead Bent (Not Twist or Broken)
Minor
NG for horizontally bent lead more than 50% of its width.
Glue or Contamination on Pin
(Couldn’t Be Removed by Alcohol)
Minor
Ink Marking on Back Side of panel
(Exclude on Film) Acceptable Ignore for Any
Ver 1.1MODULE NO.: MI12832DO-1
1.4 Cosmetic Check (Display Off) in Active Area
Check Item Classification Criteria Any Dirt & Scratch on
Polarizer’s Protective Film Acceptable Ignore for not Affect the Polarizer
Scratches, Fiber, Line-Shape Defect
(On Polarizer) Minor
W ≤ 0.1 Ignore W > 0.1, L ≤ 2 n ≤ 1 L > 2 n = 0
Dirt, Black Spot, Foreign Material,
(On Polarizer) Minor
Φ ≤ 0.1 Ignore 0.1 <Φ ≤ 0.25 n ≤ 1 0.25 <Φ n = 0
Dent, Bubbles, White spot (Any Transparent Spot on
Polarizer) Minor
Φ ≤ 0.5 Ignore if no Influence on Display
0.5 < Φ n = 0
Fingerprint, Flow Mark (On Polarizer) Minor Not Allowable
* Protective film should not be tear off when cosmetic check. ** Definition of W & L & Φ (Unit: mm): Φ = (a + b) / 2
W
L
b: Minor Axis
a: Major Axis
P.19 MULTI-INNO TECHNOLOGY CO.,LTD.
Ver 1.1MODULE NO.: MI12832DO-1
P.20 MULTI-INNO TECHNOLOGY CO.,LTD.
1.5 Pattern Check (Display On) in Active Area
Check Item Classification Criteria
No Display Major
Flicker Major Not Allowable
Missing Line Major
Pixel Short Major
Darker Pixel Major
Wrong Display Major
Un-uniform Major
Ver 1.1MODULE NO.: MI12832DO-1
CAUTIONS IN USING OLED MODULE Precautions For Handling OLED Module:
1. OLED module consists of glass and polarizer. Pay attention to the following items when handling: i. Avoid drop from high, avoid excessive impact and pressure. ii. Do not touch, push or rub the exposed polarizers with anything harder than an HB
pencil lead. iii. If the surface becomes dirty, breathe on the surface and gently wipe it off with a soft
dry cloth. If it is terrible dirty, moisten the soft cloth with Isopropyl alcohol or Ethyl alcohol. Other solvents may damage the polarizer. Especially water, Ketone and Aromatic solvents.
iv. Wipe off saliva or water drops immediately, contact the polarizer with water over a long period of time may cause deformation.
v. Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation or polarizer peeling-off may occur with high temperature and high humidity.
vi. Condensation on the surface and the terminals due to cold or anything will damage, stain or dirty the polarizer, so make it clean as the way of iii.
2. Do not attempt to disassemble or process the OLED Module. 3. Make sure the TCP or the FPC of the Module is free of twisting, warping and distortion,
do not pull or bend them forcefully, especially the soldering pins. On the other side, the SLIT part of the TCP is made to bend in the necessary case.
4. When assembling the module into other equipment, give the glass enough space to avoid excessive pressure on the glass, especially the glass cover which is much more fragile.
5. Be sure to keep the air pressure under 120 kPa, otherwise the glass cover is to be cracked. 6. Be careful to prevent damage by static electricity:
i. Be sure to ground the body when handling the OLED Modules. ii. All machines and tools required for assembling, such as soldering irons, must be
properly grounded. iii. Do not assemble and do no other work under dry conditions to reduce the amount of
static electricity generated. A relative humidity of 50%-60% is recommended. iv. Peel off the protective film slowly to avoid the amount of static electricity generated. v. Avoid to touch the circuit, the soldering pins and the IC on the Module by the body. vi. Be sure to use anti-static package.
7. Contamination on terminals can cause an electrochemical reaction and corrade the terminal circuit, so make it clean anytime.
8. All terminals should be open, do not attach any conductor or semiconductor on the terminals.
9. When the logic circuit power is off, do not apply the input signals. 10. Power on sequence: VDD VPP, and power off sequence: VPP VDD. 11. Be sure to keep temperature, humidity and voltage within the ranges of the spec,
otherwise shorten Module s life time, even make it damaged. 12. Be sure to drive the OLED Module following the Specification and Datasheet of IC
controller, otherwise something wrong may be seen.
P.21 MULTI-INNO TECHNOLOGY CO.,LTD.
Ver 1.1MODULE NO.: MI12832DO-1
13.When displaying images, keep them rolling, and avoid one fixed image displaying more than 30 seconds, otherwise the residue image is to be seen. This is the speciality of OLED.
Precautions For Soldering OLED Module: 1. Soldering temperature : 260 C 10 C. 2. Soldering time : 3-4 sec. 3. Repeating time : no more than 3 times. 4. If soldering flux is used, be sure to remove any remaining flux after finishing soldering
operation. (This does not apply in the case of a non-halogen type of flux.) It is recommended to protect the surface with a cover during soldering to prevent any damage due to flux spatters.
Precautions For Storing OLED Module: 1. Be sure to store the OLED Module in the vacuum bag with dessicant. 2. If the Module can not be used up in 1 month after the bag being opened, make sure to seal
the Module in the vacuum bag with dessicant again. 3. Store the Module in a dark place, do not expose to sunlight or fluorescent light. 4. The polarizer surface should not touch any other objects. It is recommended to store the
Module in the shipping container. 5. It is recommended to keep the temperature between 0 C and 30 C , the relative humidity
not over 60%.
Limited Warranty Unless relevant quality agreements signed with customer and law enforcement, for a period
of 12 months from date of production, all products (except automotive products) Multi-Inno will replace or repair any of its OLED modules which are found to be functional defect when inspected in accordance with Multi-Inno OLED acceptance standards (copies available upon request). Cosmetic/visual defects must be returned to Multi-Inno within 90 days of shipment. Confirmation of such date should be based on freight documents. The warranty liability of Multi-Inno is limited to repair and/or replacement on the terms above. Multi-Inno will not be responsible for any subsequent or consequential events.
Return OLED Module Under Warranty: 1. No warranty in the case that the precautions are disregarded. 2. Module repairs will be invoiced to the customer upon mutual agreement. Modules must be
returned with sufficient description of the failures or defects.
P.22 MULTI-INNO TECHNOLOGY CO.,LTD.
Ver 1.1MODULE NO.: MI12832DO-1