Post on 06-Jul-2018
transcript
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
1/86
OpenPlant Isometric Manager
V8i
Bentley Institute Course Guide
TRN016900-1/0001
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
2/86
OpenPlant Isometric Manager 2 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Trademark Notice
Bentley and the "B" Bentley logo are either registered or unregistered trademarks or
service marks of Bentley Systems, Incorporated. All other marks are the property of their
respective owners.
AccuDraw, MDL, MicroStation, and SmartLine are registered trademarks; PopSet and
Raster Manager are trademarks.
AutoCAD is a registered trademark of Autodesk, Inc.
Copyright Notice
Copyright ©2011, Bentley Systems, Incorporated. All Rights Reserved.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
3/86
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
4/86
Jul-11 4 Table of ContentsCopyright © 2011 Bentley Systems, Incorporated
Table of Contents
Questions ________________________________________37
Answers__________________________________________37
Bill of Material ______________________________________ 39Module Overview _____________________________________39
Module Prerequisites __________________________________39Module Objectives_____________________________________39
Project driven drawing output and Bill of Material Definitions __40
Module Review _______________________________________44
Questions ________________________________________44
Answers__________________________________________44
Isometric Symbols Customization ______________________ 45Module Overview _____________________________________45
Module Prerequisites __________________________________45
Module Objectives_____________________________________45
Customization of isometric symbols _______________________46
Module Review _______________________________________54
Questions ________________________________________54
Answers__________________________________________54
ProjectWise Connection ______________________________ 55Module Overview _____________________________________55
Module Prerequisites __________________________________55
Module Objectives_____________________________________55
ProjectWise Settings for Isometric Drawings ________________56
Module Review _______________________________________63
Questions ________________________________________63
Answers__________________________________________63
Management of PCF files _____________________________ 65Module Overview _____________________________________65
Module Prerequisites __________________________________65
Module Objectives_____________________________________65
Generate PCF files for passing data to legacy systems _________66
Module Review _______________________________________71
Questions ________________________________________71
Answers__________________________________________71
Course Summary ____________________________________ 73Course Summary ______________________________________73
Course Review ________________________________________74
Questions ________________________________________74
Answers__________________________________________75
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
5/86
Jul-11 5 Table of ContentsCopyright © 2011 Bentley Systems, Incorporated
Table of Contents
Appendix A ________________________________________ 77rep_sortgroups.txt_____________________________________77
Appendix B ________________________________________ 81report.def____________________________________________81
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
6/86
Table of Contents 6 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Table of Contents
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
7/86
Jul-11 7 Course Overview
Copyright © 2011 Bentley Systems, Incorporated
Course Overview
Course Description
This course is designed to instruct the project administrator how to customize
Isometric Drawings to meet corporate standards.
You will be instructed on how to setup isometrics styles, how to customize
drawing attributes for additional pipeline information. You will learn how to
configure Bill of Material output and layout. You will also create custom isometricsymbols. You will be instructed how to generate PCF files for passing data to
legacy systems and how to set connection to ProjectWise for deliverables
Management.
Target Audience
This course is recommended for the following audience(s):
• Engineers, Designers and Drafters responsible for customizing IsometricManager software to fit their corporate needs.
Prerequisites
• Students taking this course should have a working knowledge of MicroStation
and 3D modeling concepts.
• Students should have completed the OpenPlant Modeler User training.
• Students should have understanding of OpenPlant Modeler, of OpenPlantprojects and of OpenPlant Model Server.
• Students should have working knowledge of ProjectWise Explorer.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
8/86
Course Overview 8 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Course Objectives
Course Objectives
After completing this course, you will be able to:
• Use the Isometric Configuration tool.
• Customize drawing attributes for additional pipeline information.• Setup drawing layout and Bill of Material definitions.
• Customize existing and create new custom isometric symbols.
• Set Isometric Revision Format.
• Set connection to ProjectWise for deliverables Management.
• Allow PCF File Generation.
Modules Included
The following modules are included in this course:
• Isometric Style Setup
• Design State Mapping and Revisions control
• Drawing Attributes
• Bill of Material
• Isometric Symbols Customization
• ProjectWise Connection
• Management of PCF files
System Requirements
You must have a CD drive or Internet access for product installation. The
following prerequisites are required to run the OpenPlant Isometric
Manager(SELECTseries3):
Processor: Intel Pentium 4 processor or AMD Athlon, 3.0 GHz or greater, or Intel
or AMD Dual Core Processor, 2.0 GHZ or greater
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
9/86
Jul-11 9 Course OverviewCopyright © 2011 Bentley Systems, Incorporated
Software Requirements
Operating System: Windows 7, Windows 7 x64, Windows Vista, Windows Vista
x64, Windows XP Professional (SP2 or later) Windows XP Professional x64,
Windows XP Home Edition (SP2 or later), Windows XP Tablet PC Edition,
Windows 2000 Professional (SP3 or later), Windows 2000 Server, Windows
Server 2003 (SP1 or later), Windows Server 2003 x64, Windows Server 2008,
Windows Server 2008 x64.
Microsoft Office: Professional Edition 2000 (SR1a), XP, 2003 or 2007.
Memory: 2GB minimum recommended (More memory almost always improves
performance, particularly when working with larger models.).
Hard Disk: Requires 30 MB minimum free hard disk space in addition to the
OpenPlant Modeler V8i requirement of 400 MB minimum free hard disk space.
Input Device: Any industry-standard input device supported by Windows.
Output Device: Any industry-standard output device supported by Windows.
Software Requirements
ProjectWise Explorer V8i (SELECTseries 2), Bentley OpenPlant Modeler V8i
(SELECTseries 3), Network access to OpenPlant ModelServer V8i .
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
10/86
Course Overview 10 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Software Requirements
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
11/86
Jul-11 11 Isometric Style Setup
Copyright © 2011 Bentley Systems, Incorporated
Isometric Style Setup
Module Overview
In order to control generation of different types of Isometric Drawings, an
administrator will need to define new and modify existing styles and their base
default values used for an Isometric Drawing generation.
Module Prerequisites
• Students should have completed the OpenPlant Modeler User course.
Module Objectives
After completing this module, you will be able to:
• Use Isometric Configuration tool to specify basic parameters of IsometricDrawings.
• Create a new Isometric Style.
• Set Design State mapping.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
12/86
Isometric Style Setup 12 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Isometric Manager Styles
Isometric Manager Styles
Isometric Drawings generated in different project stages have to meet different
requirements. We will address the different isometric styles.
The Isometric Configuration tool enables you to set a Default Isometric Style forthe whole project.
If different Isometric Styles are to be used for Isometric Drawing generation,
Design States have to be mapped to these styles.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
13/86
Jul-11 13 Isometric Style SetupCopyright © 2011 Bentley Systems, Incorporated
Isometric Manager Styles
You can define as many isometric styles as required. Isometric Style features can
be set by:
• Using the Isometric Configuration tool.
• Customizing configuration text files located in the project Workspace
directory.
Isometric Style setting using the Isometric Configuration
tool
There are three dialogs available to change the Isometric Style features. They are
the Isometric Style dialog, the Isometric Drawing Attributes dialog and the Label
dialog.
The Isometric Style dialog enables you to specify basic parameters.
• Graphical Configuration tool: This field is used to start an OP Modeler session
and to customize the isoseed file used for creating Isometric Drawings.
• Completed Isometric Design State: This parameter specifies which design
state to set piping components when an Isometric Drawing is created and
placed into ProjectWise.
The Isometric Drawing Attributes dialog is described in more detail in the module
Drawing Attributes.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
14/86
Isometric Style Setup 14 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Isometric Manager Styles
The Label dialog specifies the labels to be used on an Isometric Drawing.
Isometric Style Setting using Configuration Text Files
For example, for the As-Built style the following configuration text files located in:
C:\ProgramData\Bentley\OpenPlantModelerV8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\As-
Built\Config
• isoextract.dat: no longer needed.
• node2da.txt: mapping of textnode numbers to named drawing attributes.
• operator.tbl: mapping of operator names (as supplied by OPM) to symbols to
be used in isometrics.
• pcf.ini: configuration for IsoExtractor PCF writer.
• rep_sortgroups.txt: definition of sort groups for Bill of Material.
• report.def : definitions for all reports produced by IsoExtractor.
• scaler.ini: scale settings.
• style.cfg: IsoExtractor configuration file.
• symbolsizes.def : definitions of the basic scaler classes.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
15/86
Jul-11 15 Isometric Style SetupCopyright © 2011 Bentley Systems, Incorporated
Isometric Manager Styles
All text files include a short description of the purpose and their content is well
commented.
The file isoseed.dgn located in the same directory is a seed used by Iso extractor
when an iso drawing is created.
Exercise: Create a new Isometric Style
The goal of this exercise is to create a new Isometric Style called Training
based on an existing Isometric Style As-Built. It will be set as the default for
Iso Sheets in the Design State of In Checking.
1 Select Tools > Configuration.
2 Right-click on Isometric Style.
3 Click Add New Style.
4 Select As-Built from the Select Base Style list.
5 Type Training in the Name of Style field.
6 Click OK.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
16/86
Isometric Style Setup 16 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Isometric Manager Styles
The following message appears:
7 Navigate to the C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics
directory.
8 Open the file StyleListing.cfg in Notepad.
9 Add the following text in the List of Styles section.
10 Save the file.
11 Exit the Isometric Manager and start it again.
12 Select Tools > Configuration or click the Configuration icon.
13 Select Model Server Design State Mapping > InChecking.
14 Select Training from the Isometric Style list.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
17/86
Jul-11 17 Isometric Style SetupCopyright © 2011 Bentley Systems, Incorporated
Isometric Manager Styles
Note: To remove an existing style you can select it in the Isometric Style list,
right-click and select Remove.
Note: If a style is used (for example assigned to a Design State) it can't be
removed.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
18/86
Isometric Style Setup 18 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Module Review
Module Review
Now that you have completed this module, let’s measure what you have learned.
Questions
1 Why we are using Model Server Design State Mapping?
2 What is specified by the Completed Isometric Design State parameter?
3 True/False: Using Isometric the Isometric Configuration tool is the only
way how to customize Isometric Styles.
Answers
1 Model Server Design State Mapping enables to use different IsometricStyles for processing of Iso Sheets with respect to their Design States.
2 Completed Isometric Design State parameter specifies to which design
state to set piping components when an Isometric Drawing is created and
put into ProjectWise.
3 False: Isometric Style features can be set by using the Isometric
Configuration tool or by customizing configuration text files located in the
project Workspace directory.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
19/86
Jul-11 19 Design State Mapping and Revision Control
Copyright © 2011 Bentley Systems, Incorporated
Design State Mapping and
Revision Control
Module Overview
Isometric Manager enables to map single Design States to specific Isometric
Styles. Administrator will need to modify this mapping and to customize it to
meet company requirements.
Module Prerequisites
• Students should have completed the OpenPlant Modeler User course.
• Students should have understanding of OpenPlant Modeler.
Module Objectives
After completing this module, you will be able to:• Map Design States to Isometric Styles.
• Set Isometric Revision format and other Design State based properties.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
20/86
Design State Mapping and Revision Control 20 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Design State Mapping
Design State Mapping
Isometric Manager enables to set mapping between Design States and Isometric
Styles.
Note: This module explains Model Server Design State Mapping but exactly the sameprocedures can be applied for i-model Design State Mapping.
Exercise 1: Isometric Style setting.
The target of this exercise is to map Design State InDesign to the Isometric
Style IFC.
1 Select Tools > Configuration or click the Configuration icon.
2 Expand Model Server Design State Mapping.
3 Select InDesign.
4 Select IFC from the Isometric Style list.
5 Click Save.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
21/86
Jul-11 21 Design State Mapping and Revision ControlCopyright © 2011 Bentley Systems, Incorporated
Design State Mapping
The Isometric Style assignment is applied.
Note: If you do not click Save and click in the left part of the Isometric
Configuration dialog a warning message appears. Click Yes to confirm
changes.
6 Close the Isometric Configuration dialog.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
22/86
Design State Mapping and Revision Control 22 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Revision control
Revision control
Revisions are assigned to Isometric Drawings based on Isometric Revision setting
specified for each Design State. If no specific Isometric Revision format is
specified for a used Design State, the system uses the Isometric Revision format
set for a Project. Isometric Revision formats set for a Design Stage has a priority.
A revision is set for an iso drawing during its creation. The system checks
ProjectWise for the last revision of the generated Isometric Drawing and assigns
the next available revision.
Exercise 1: Isometric Revision setting
The goal of this exercise is to set a format of Revision for IFC Isometric Style to
R1, R2, etc.
1 Select Tools > Configuration or click the Configuration icon.
2 Expand Model Server Design State Mapping.
3 Select InDesign.
4 Select IFC from the Isometric Style list.
5 Select the Isometric Revision field.
6 Click Browse.
The Revision Settings dialog opens.
7 Set Customized in the Revision Format group box.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
23/86
Jul-11 23 Design State Mapping and Revision ControlCopyright © 2011 Bentley Systems, Incorporated
Revision control
8 Set the Prefix , Separator and Postfix fields as shown below:
9 Click Test.
10 Click Next.
The Customized Revision is set to R0.
11 Click Next.
The Customized Revision is set to R1.
12 Set Set as starting value.
13 Click OK.
14 Click OK.
The Customized Revision dialog closes.
15 Click OK.
The Revision Settings dialog closes.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
24/86
Design State Mapping and Revision Control 24 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Revision control
16 Click Save.
The new Isometric Revision setting is applied.
17 Close the Isometric Configuration dialog.
Exercise 2: Isometric Name setting
An Isometric Name is the name which is assigned to an automatically
generated Isometric Drawing. The goal of this exercise is to set the IsometricName to – .
1 Select Tools > Configuration or click the Configuration icon.
2 Expand Model Server Design State Mapping.
3 Select InDesign.
4 Select the Isometric Name field.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
25/86
Jul-11 25 Design State Mapping and Revision ControlCopyright © 2011 Bentley Systems, Incorporated
Revision control
5 Click Browse.
6 Select LINENUMBER from the Property field list.
7 Click Add.
8 Type - in the Text field.
9 Select DESIGN_STATE from the Property field list.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
26/86
Design State Mapping and Revision Control 26 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Revision control
10 Click Add.
11 Click OK.
To close the Isometric Name Expression Editor dialog.
12 Click Save.
To apply the new Isometric Name setting.
13 Close the Isometric Configuration dialog.
Exercise 3: Design States Color setting
Design States Color specifies a color used to display Iso Sheet in the Isometric
Manager window. It helps to distinguish groups of iso sheets in the same
Design State. The goal of this exercise is to display Iso Sheets assigned to theDesign State InDesign in the Red color.
1 Select Tools > Configuration or click the Configuration icon.
2 Expand Model Server Design State Mapping.
3 Select InDesign.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
27/86
Jul-11 27 Design State Mapping and Revision ControlCopyright © 2011 Bentley Systems, Incorporated
Revision control
4 Select the Design States Color field.
5 Click Browse.
6 Select Red color.
7 Click OK.
8 Click Save.
The new Design States Color setting is applied.
9 Click Close.
The Isometric Configuration dialog closes.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
28/86
Design State Mapping and Revision Control 28 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Module Review
Module Review
Now that you have completed this module, let’s measure what you have learned.
Questions
1 True/False: Assignment of Design States to Isometric Styles is managed by
the ProjectWise Administrator application.
2 True/False: The Revision format of Isometric Drawings can be Alphabetic
or Numerical.
3 True/False: Design States Color enables to distinguish if a Design State of
an Isometric Drawing has changed or not.
Answers1 False: Mapping between Design States and Isometric Styles is managed by
the Configuration tool which is a part of the Isometric Manager interface.
2 False: The Revision format of Isometric Drawings can be Alphabetic,
Numerical or Customized.
3 False: Design States Color specifies a color used to display Iso Sheets in the
Isometric Manager window. It helps to distinguish groups of iso sheets in
the same Design State.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
29/86
Jul-11 29 Drawing Attributes
Copyright © 2011 Bentley Systems, Incorporated
Drawing Attributes
Module Overview
Drawing Attributes are used on Isometric drawings to give more information
about the pipeline from which the Isometric was extracted. An administrator will
need to modify the attributes to be used on the Isometric drawings and where
they should be placed based on the company requirements.
Module Prerequisites
• Students should have completed the OpenPlant Modeler User course.
• Students should have a working knowledge of MicroStation.
• Students should have understanding of OpenPlant Modeler.
Module Objectives
After completing this module, you will be able to:
• Modify attributes that will be placed on Isometric drawings.
• Modify a seed file to customize the position of Drawing Attributes.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
30/86
Drawing Attributes 30 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of drawing attributes for additional pipeline information
Customization of drawing attributes for additional pipeline
information
Let us suppose you need to add the attribute INTERNAL_PRESSURE to attributes
displayed on an Isometric drawing generated using Isometric Style IFC. The whole
procedure can be divided into three steps:
Customization of selected attributes.
Customization of the seed file isoseed.dgn.
Customization of the mapping file node2da.txt.
Exercise 1: Customization of selected attributes
1 Select Tools > Configuration or click the Configuration icon.
2 Select Isometric Style > IFC > Drawing Attributes in the Isometric
Configuration dialog.The table which appears in the right window shows the pre-defined
drawing attributes provided by the system for the Isometric Style IFC.
By default there are available 32 attributes for each Isometric Style to be used
on an Isometric Drawing. Each so called Drawing Attribute Collection is
specified by the NAME and by the VALUE .
Attributes can be added or deleted from the default list.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
31/86
Jul-11 31 Drawing AttributesCopyright © 2011 Bentley Systems, Incorporated
Customization of drawing attributes for additional pipeline information
To delete an attribute select it, right-click and select Delete Attribute.
As the INTERNAL_PRESSURE is not currently among displayed attributes we
have to add it.
3 Navigate to the top of the Isometric Drawing Attributes list to the Drawing
Attribute Collection field, right-click and select Add Attribute.
A new empty section is created to define a new attribute.
4 Type Internal_Pressure in the NAME field.
5 Click Browse in the VALUE field.
6 Set Use ECProperty.
7 Set Use Parent Class.
8 Select PIPING_NETWORK_SYSTEM in the Use Parent Class group box.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
32/86
Drawing Attributes 32 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of drawing attributes for additional pipeline information
9 Select INTERNAL_PRESSURE in the Property field.
10 Click OK.
11 Click SAVE.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
33/86
Jul-11 33 Drawing AttributesCopyright © 2011 Bentley Systems, Incorporated
Customization of drawing attributes for additional pipeline information
Note: There are another 2 options to specify a Value of a Drawing Attribute:
• Use Expressions: This option allows you to define an EC property for
the Iso_Sheet class to be displayed as the value for the drawing
attribute.
• Using ECProperty: The option is related to the ISO_SHEET class (and
not to a parent class as used above in step 7). When used, this optionenables you to select a property from the ISO_SHEET Property list to
be displayed in the Value field.
Exercise 2: Customization of the seed file isoseed.dgn
We defined a new Drawing Attribute in the last exercise, as the next step it is
necessary to set the location of the Drawing Attribute on Isometric drawing.
1 Select Isometric Style > IFC.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
34/86
Drawing Attributes 34 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of drawing attributes for additional pipeline information
2 Click Browse in the Graphical Configuration tool field.
Bentley OpenPlant Modeler session starts and the file isoseed.dgn located
in the project directory C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\I
FC\Config is opened.
3 Press CTRL + B or navigate to View Attributes and switch on Text Nodes.
4 Navigate to the bottom of the drawing to see currently assigned Text
Nodes.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
35/86
Jul-11 35 Drawing AttributesCopyright © 2011 Bentley Systems, Incorporated
Customization of drawing attributes for additional pipeline information
5 Using MicroStation tools, extend the attribute field as specified below:
6 Select by window Des temp and Text Node 25 and copy these texts to the
left:
The Text Node number was automatically updated to the first next
available number 65.
Note: If you want a specific node number you can do the following: suppose
you want node 24. Before doing the copy enter the key-in command:
NN=24
7 Replace Des temp with Int press.
8 Exit isoseed.dgn.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
36/86
Drawing Attributes 36 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of drawing attributes for additional pipeline information
Exercise 3: Customization of the mapping file node2da.txt
1 Navigate to C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\I
FC\Config.
2 Open the file node2da.txt.
This file maps a text node numbers to named Drawing Attributes. Each
line specifies one mapping.
3 Add a new line at the end of this text file:
65, Internal_Pressure
65 is the number of the Text Node inserted in the isoseed.dgn
customization and the text string Internal_Pressure has to correspond to
the text specified in the Drawing Attribute definition.
4 Save and close the file node2da.txt.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
37/86
Jul-11 37 Drawing AttributesCopyright © 2011 Bentley Systems, Incorporated
Module Review
Module Review
Now that you have completed this module, let’s measure what you have learned.
Questions
1 True/False: Drawing Attributes are defined once for the whole project.
2 True/False: The number of Drawing Attributes is limited to 32.
3 True/False: All Drawing Attributes defined in Isometric Drawing Attributes
list are automatically placed in a generated Isometric drawing.
Answers
1 False: Drawing Attributes are defined for each Isometric Style separately.2 False: The number of Drawing Attributes is not limited to 32. Another
Drawing Attributes can be add by the Add Attribute function.
3 False: User can decide which Drawing Attributes will be used on an
automatically generated Isometric Drawing. Customization is done using
two files: isoseed.dgn and node2da.txt.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
38/86
Drawing Attributes 38 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Module Review
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
39/86
Jul-11 39 Bill of Material
Copyright © 2011 Bentley Systems, Incorporated
Bill of Material
Module Overview
A Bill of Material is automatically generated during the Isometric extraction
process. An administrator will need to modify which properties should be
included in a Bill of Material and to customize their layout on an Isometric
drawing based on the company requirements.
Module Prerequisites
• Students should have completed the OpenPlant Modeler User course.
• Students should have a working knowledge of MicroStation.
• Students should have understanding of OpenPlant Modeler.
Module Objectives
After completing this module, you will be able to:
• Modify a report definition file.
• Modify a seed file to customize the Bill of Material layout.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
40/86
Bill of Material 40 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Project driven drawing output and Bill of Material Definitions
Project driven drawing output and Bill of Material Definitions
Isometric Extractor reports – Bills of Material (BOM) - are generic reports that
operate on component properties and are an integral part of each Isometric
drawing. This BOMs can contain any database information connected with a
piping component existing on an Isometric drawing. Generated reports are plaintext files that can be attached to a text node in an Isometric drawing.
A BOM is defined for each Isometric Style separately.
See Appendix 1 for full description of the Report.def file. The file is very well
commented.
Exercise 1: Customization of the file Report.def
The goal of this exercise is to include the property MATERIAL in a BOM
generated on your Isometric Drawings defined by the Isometric Style IFC.
1 Navigate to C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\I
FC\Config.
2 Open Report.def with a text editor.
3 Navigate to the section REPORT = SHP, which writes shop material to a
report
Note:
Column definition has the following syntax. :
COLUMN = : :
Where
specifies the width of the column in character positions
is a combination of:
L left aligned
R right aligned
C centered
W wrap, a new line will be added if the length of the expression
exceeds the width of the report
is an expression for the content of the report column.
Any component attribute or string can be used. Example:IE_DESCRIPT + UUID + "and a string" would concatenate the atributes
IE_DESCRIPT and UUID and the string "and a string"
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
41/86
Jul-11 41 Bill of MaterialCopyright © 2011 Bentley Systems, Incorporated
Project driven drawing output and Bill of Material Definitions
4 Change the line
COLUMN = 19: R : QUANTITY
to
COLUMN = 9: R : QUANTITY
5 Add a new line after just edited lineCOLUMN = 10: L : STOCK_NUMBER
6 Repeat steps 4 and 5 in the section REPORT = FLD which writes field
material to a report.
7 Close Report.def .
Changes done in the Report.def file must be followed by changes in a seed
file used for Isometric Drawing generation. This will be done in the next
exercise.
Exercise 2: Configure Bill of Material layout
When a user customizes the Report.def file it is also necessary to make
corresponding changes in the file Isoseed.dgn, which is a seed file used by
Isometric Manager to create Isometric drawings. Mostly it means to change a
heading of the Bill of Materials.
The goal of this exercise is to customize a heading of a Bill of Material to
include the property STOCK NUMBER added to the BOM definition in the
previous exercise.
1 Select Tools > Configuration or click the Configuration icon.
2 Select Isometric Style > IFC.
3 Click Browse in the Graphical Configuration tool field.
Bentley OpenPlant Modeler session starts and the file isoseed.dgn located
in the project directory C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\I
FC\Config is opened.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
42/86
Bill of Material 42 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Project driven drawing output and Bill of Material Definitions
4 Navigate to the upper part of the BOM heading.
5 Double-click on Quantity and edit it to Quant.
6 Right-click on Quant and select Move.
7 Move text 7.4 mm to the left.
8 Right-click on Quant and select Copy.
9 Copy text 14 mm to the right.
10 Double-click the copied Quant text and edit it to Stock N.
11 Move the cursor over the line between Material and Size1, right-click and
select Copy.
12 Copy this line 15 mm to the left.
13 Exit isoseed.dgn.
14 Generate an Isometric Drawing to see changes have been applied.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
43/86
Jul-11 43 Bill of MaterialCopyright © 2011 Bentley Systems, Incorporated
Project driven drawing output and Bill of Material Definitions
Note: At least one of the piping components from which Isometric drawing
will be generated has to have a Stock Number property assigned.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
44/86
Bill of Material 44 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Module Review
Module Review
Now that you have completed this module, let’s measure what you have learned.
Questions
15 True/False: Customization of properties to be included in a Bill of Material
can be done in the file style.cfg.
16 True/False: A layout of the Shop section and a layout of the Field section
of Bill of Material are defined separately.
Answers
1 False: Customization of properties to be included in a Bill of Material can
be done in the file report.def.
2 True: The section REPORT = SHP of the report.def file writes Shop material
to a report and the section REPORT = FLD writes Field material to a report.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
45/86
Jul-11 45 Isometric Symbols Customization
Copyright © 2011 Bentley Systems, Incorporated
Isometric Symbols
Customization
Module Overview
Isometric symbols used on Isometric Drawings are stored in cell libraries. Based
on company requirements an Administrator will need to modify existing symbols
or to create completely new symbols.
Module Prerequisites
• Students should have completed the OpenPlant Modeler User course.
• Students should have a working knowledge of MicroStation.
• Students should have understanding of OpenPlant Modeler.
Module Objectives
After completing this module, you will be able to:
• Change a shape of an isometric symbol.
• Create a new isometric symbol to be used on Isometric Drawings.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
46/86
Isometric Symbols Customization 46 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of isometric symbols
Customization of isometric symbols
Isometric symbols are stored in cell libraries. Isometric Manager enables to
define a set of isometric symbols independently for each Isometric Style. For
example, libraries used for the Isometric Style IFC are located in
C:\ProgramData\Bentley\OpenPlantModelerV8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\IFC\Cell\
.
Assignment of OpenPlant Components to names of iso symbols used by Isometric
Manager is done in
Openplant_3d_supplemental_isometrics_isoextractor.01.01.ecschema.xml
located in C:\ProgramData\Bentley\OpenPlantModeler V8i
\WorkSpace\Projects\OPModeler_Metric\DataSet\Schemas.
Exercise 1: Change a shape of the flanged Gate Valve Iso symbol used for the
Isometric Style IFC
The goal of this exercise is to change an existing symbol for gate valve
to
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
47/86
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
48/86
Isometric Symbols Customization 48 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of isometric symbols
A model of GATFL opens.
7 Select Place Circle from the Drawing toolbar.
8 When prompted Place Circle by Center > Identify Center Point click the
center of the Gate Valve using Intersect Snap and specify diameter as
shown below.
9 Click the Element Selection tool.
The Place Circle command is closed.
10 Exit OpenPlant Modeler.
11 Click Close.
The Isometric Configuration dialog closes.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
49/86
Jul-11 49 Isometric Symbols CustomizationCopyright © 2011 Bentley Systems, Incorporated
Customization of isometric symbols
12 Generate an Isometric drawing containing flanged gate valve to see your
customized symbol.
Exercise 2: Create a new Iso symbol used for the Isometric Style IFC.
The goal of this exercise is to create a new iso symbol of a flanged Gate Valve.
1 Select Tools > Configuration or click the Configuration icon.
2 Click Browse in the Graphical Configuration tool field.
3 When OpenPlant Modeler starts, select IsoExtractor > Cell Creation Tool.
4 Click the Open Template File in the Create Cell toolbar.
Note: OpenPlant Isometric Manager offers a set of iso symbol templates
which were used to create an existing cell library and can be also used
to define new symbols to be placed on Isometric drawings. These
templates are located in
C:\ProgramData\Bentley\OpenPlantIsometricsManagerV8i\WorkSpace
\OPIM\cellTemplates.
5 Create a copy of valves.dgn to keep the original file untouched.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
50/86
Isometric Symbols Customization 50 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of isometric symbols
6 Select the copy and click Open.
7 Navigate to Gate Valve symbols.
8 Zoom in to the flanged Gate valve symbol.
9 Select Place Circle from the Drawing toolbar.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
51/86
Jul-11 51 Isometric Symbols CustomizationCopyright © 2011 Bentley Systems, Incorporated
Customization of isometric symbols
10 When prompted Place Circle by Center > Identify Center Point click the
center of the Gate Valve using Intersect Snap and specify diameter as
shown below.
11 Click the Element Selection tool.
The Place Circle command is closed.
12 To distinguish the new symbol from a symbol customized previously in the
cell library, select the new circle and change the weight of the active line
to 4.
13 Select Tasks > Place Fence.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
52/86
Isometric Symbols Customization 52 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Customization of isometric symbols
To place a fence around a customized symbol.
14 Click Create cell.
15 Select custom.cel from the Cell Library selection list and type in.
Cell Name: GATFL
Description: Customized GATFL
16 Click OK.
The new cell is created.
Note: To save graphics as an iso cell at least one connection point is needed.
As we were using a graphics of an existing symbol, connection pointswere already specified. If not we would have to use Place Connect
Point.
Note: If required we can also place Origin Point or Intersection Point (for
example for Tee components) from the Create Cell toolbar.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
53/86
Jul-11 53 Isometric Symbols CustomizationCopyright © 2011 Bentley Systems, Incorporated
Customization of isometric symbols
Note: During the Isometric drawing creation Isometric Manager first tries to
locate a symbol in the custom.cel library and if the required symbol is
not found there it is taken from the default library isocomp.cel. It
enables us to use the original name GATFL for the new customized
symbol.
Note: To find a name of a cell used by the Isometric Manager open an
Isometric drawing containing a symbol of a corresponding component
and hover the pointer over it.
Note: When the cell is not present in the cell libraries during creation a red
circle will appear at the position of the missing cell. Hovering over the
red circle will show the name of the missing cell.
17 Exit OpenPlant Modeler.
18 Click Close.
The Isometric Configuration dialog closes.
19 Generate an Isometric drawing containing flanged Gate Valve to see your
customized symbol.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
54/86
Isometric Symbols Customization 54 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Module Review
Module Review
Now that you have completed this module, let’s measure what you have learned.
Questions
1 True/False: Symbols to be placed on Isometric Drawings are defined in
the file isoseed.dgn located for the IFC Isometric Style in
C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\I
FC\Config
2 True/False: To define new isometric symbols you have to use standard
MicroStation drawing tools and to draw them from scratch.
3 True/False: When the cell is not present in the cell libraries during
creation an empty space will appear at the position of the missing cell.
Answers
1 False: Isometric symbols are stored in cell libraries. Isometric Manager
enables to define a set of isometric symbols independently for each
Isometric Style. For example libraries used for the Isometric Style IFC are
located in C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\I
FC\Cell\
2 False: OpenPlant Isometric Manager offers a set of iso symbol templateswhich were used to create an existing cell library and can be also used to
define new symbols to be placed on Isometric Drawings. These templates
are located in
C:\ProgramData\Bentley\OpenPlantIsometricsManagerV8i\WorkSpace\O
PIM\cellTemplates
3 False: When the cell is not present in the cell libraries during creation a
red circle will appear at the position of the missing cell. Hovering over the
red circle will show the name of the missing cell.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
55/86
Jul-11 55 ProjectWise Connection
Copyright © 2011 Bentley Systems, Incorporated
ProjectWise Connection
Module Overview
There is a direct connection between OpenPlant Isometric Manager and
ProjectWise. The administrator will need to create the connection and specify the
behavior of Isometric Manager to meet company requirements.
Module Prerequisites
• Students should have completed the OpenPlant Modeler User course.
• Students should have understanding of OpenPlant Modeler.
• Students should have working knowledge of ProjectWise Explorer.
Module Objectives
After completing this module, you will be able to:
• Set Root Storage Folder to store Isometric Drawings.
• Allow Design Style switching.
• Set rules for transfer of Isometric drawings between Isometric Manager and
ProjectWise folders.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
56/86
ProjectWise Connection 56 Jul-11Copyright © 2011 Bentley Systems, Incorporated
ProjectWise Settings for Isometric Drawings
ProjectWise Settings for Isometric Drawings
Isometric Manager enables you to post generated Isometric drawings to
ProjectWise and perform additional tasks. There are several settings which
influence this process:
• Root Storage Folder
• Allow To Create Folders
• Allow Design State Switching
• Document Posting
Exercise 1: Root Storage Folder
When you successfully generate an Isometric drawing you can post it to
ProjectWise.
The goal of this exercise is to configure Isometric Manager to select the
Training_Isometrics folder as a root folder for storing Isometric drawings
when you initiate the Post to ProjectWise procedure.
1 Select Tools > Configuration or click the Configuration icon.
2 Select Project.
3 Click Browse in the Root Storage Folder field.
4 Navigate to ROOT which corresponds to the Documents folder in theProjectWise datasource folder structure.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
57/86
Jul-11 57 ProjectWise ConnectionCopyright © 2011 Bentley Systems, Incorporated
ProjectWise Settings for Isometric Drawings
5 Right-click and select New Folder.
6 Type Training_Isometrics in the Name field.
7 Type Training Isometrics in the Description field.
8 Click OK.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
58/86
ProjectWise Connection 58 Jul-11Copyright © 2011 Bentley Systems, Incorporated
ProjectWise Settings for Isometric Drawings
The new root folder Training_Isometrics is created and the Isometric
Configuration dialog returns.
9 Select True in the Allow to Create Folder field.
This setting will enable automatic creation of subfolders below the
Isometric Root Storage folder inside ProjectWise. Subfolder structure is
specified by the Property Storage Path assigned to the Class Name Iso
Sheet in the schema
OpenPlant_3D_Supplemental_Modeling.08.11.ecschema.xml. This
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
59/86
Jul-11 59 ProjectWise ConnectionCopyright © 2011 Bentley Systems, Incorporated
ProjectWise Settings for Isometric Drawings
schema is located in C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Schemas.
If set as above, ProjectWise will automatically create a folder structure
below the Training_Isometrics folder which will be done by SERVICE , UNIT
and LINENUMBER of a pipeline posted by Isometric Manager to
ProjectWise.
10 Click Save.
To store changes in the ProjectWise Folder Setting dialog.
Note: You can start ProjectWise, login into the OP_Training_M datasource and
check the Training_Isometrics folder that was created below the
Documents folder.
11 Click Close.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
60/86
ProjectWise Connection 60 Jul-11Copyright © 2011 Bentley Systems, Incorporated
ProjectWise Settings for Isometric Drawings
To close the Isometric Configuration dialog.
Exercise 2: Design State Switching
When an Isometric drawing is created and put into ProjectWise the Design
State of the components used to create an Isometric drawing can be
automatically changed.
This exercise will teach you how to allow Design State Switching to change the
design state of Iso Sheets for the Isometric drawing from the Isometric Style
IFC to the Design State IFC.
1 Select Tools > Configuration or click the Configuration icon.
2 Select Project.
To open the General window.
3 Select True from the Allow Design State Switching field.
4 Click Save.
5 Expand the Isometric Style node and select IFC.
The Isometric Style window opens.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
61/86
Jul-11 61 ProjectWise ConnectionCopyright © 2011 Bentley Systems, Incorporated
ProjectWise Settings for Isometric Drawings
6 Select IFC from the Completed Isometric Design State field.
7 Click Save.
The changes are saved.
8 Click Close.
9 The Isometric Configuration dialog closes.
Exercise 3: Document Posting
An Isometric Manager administrator can specify what has to be done after an
Isometric drawing generation.
The goal of this exercise is to enable Isometric drawings to be reviewed
before posting them to ProjectWise and to delete them from the Isometric
drawings list (right bottom part of the Isometric Manager interface) at the
moment they are posted to ProjectWise.
1 Select Tools > Options or click the Options icon.
The following dialog opens.
Note: What happens with generated Isometric Drawings depends on setting
of Document Posting options.
2 Set Review generated isometrics before posting.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
62/86
ProjectWise Connection 62 Jul-11Copyright © 2011 Bentley Systems, Incorporated
ProjectWise Settings for Isometric Drawings
Note: If the Review generated isometrics before posting option is set the
generated Isometric drawing is available for reviewing when generated.
If this option is not set the Isometric drawing is immediately sent to
ProjectWise when generated.
3 Set Delete document from system after posting.
Note: If the Delete document from system after posting option is set the
generated Isometric drawing disappears from the list of generated
Isometric drawings when posted to ProjectWise. If this option is cleared
the generated Isometric drawing does not disappear from the list of
generated Isometric drawings when posted to ProjectWise. The
Progress Message is changed to Isometric Posted Successfully.
4 Clear List only those components that have Valid Design States.
Note: If the List only those components that have Valid Design States option is
set , only Iso Sheets that have a valid design state (as determined by the
administrator) are displayed in the Iso Sheets pane of the interface.
5 Clear Log Isometric Dataset.
Note: Whenever an Isometric drawing is generated, a Production Log file is
created containing information on the isometric generation process.
When the Log Isometric Dataset option is set , a complete dataset for
the isometric is logged into the Production Log file which can be used
for debugging if the isometric generation fails. When you clear the
ProjectWise Managed Workspace dgn path, the next time you start
Isometrics Manager in a managed workspace you will have to use the
setup process again to identify a new file path for the workspace.
6 Click OK.
The Options dialog is closed.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
63/86
Jul-11 63 ProjectWise ConnectionCopyright © 2011 Bentley Systems, Incorporated
Module Review
Module Review
Now that you have completed this module, let’s measure what you have learned.
Questions
1 True/False: The Allow to Create Folders option enables to create a new
root folder to store Isometric Drawings.
2 True/False: Each Iso Sheet has to have a Design State defined. When you
set the Allow Design State Switching option to True Design State
automatically changes to the next state as specified by pre-defined
workflow when you generate an Isometric Drawing from it.
3 True/False: If the Delete document from system after posting option is
checked the Iso Sheet used for an Iso Drawing generation disappears from
the list of IsoSheets available for processing.
Answers
1 False: The Allow to Create Folders option enables automatic creation of
subfolders below the Isometric Root Storage folder inside ProjectWise.
Subfolder structure is specified by the Property Storage Path assigned to
the Class Name Iso Sheet.
2 False: Each Iso Sheet has to have a Design State defined. When you set the
Allow Design State Switching option to True for a project it is possible to
specify the Completed Isometric Design State value for each IsometricStyle. Next time you generate an Isometric Drawing a Design State of Iso
Sheet automatically changes to a state as specified for this Isometric Style.
3 False: If the Delete document from system after posting option is checked
the generated Isometric Drawing disappears from the list of generated
Isometric Drawings when posted to ProjectWise. If this option is not
checked the generated Isometric Drawing does not disappear from the list
of generated Isometric Drawings when posted to ProjectWise. Just the
Progress Message is changed to Isometric Posted Successfully.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
64/86
ProjectWise Connection 64 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Module Review
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
65/86
Jul-11 65 Management of PCF files
Copyright © 2011 Bentley Systems, Incorporated
Management of PCF files
Module Overview
The Isometric Manager can create PCF files during Isometric drawings generation
which can be used by other applications. A system administrator has a several
options connected with creation and evaluation of these PCF files.
Module Prerequisites
• Students should have completed the OpenPlant Modeler User course.
• Students should have understanding of OpenPlant Modeler.
• Students should have working knowledge of ProjectWise Explorer.
Module Objectives
After completing this module, you will be able to:
• Allow PCF files generation.
• Influence Isometric Drawing generation if generation of a PCF file fails.
• View or export PCF files.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
66/86
Management of PCF files 66 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Generate PCF files for passing data to legacy systems
Generate PCF files for passing data to legacy systems
The Isometric Manager can create a PCF file as a by-product during the Isometric
drawing generation. These PCF files can be used by other applications. The
Isometric Manager offers several options and features connected with PCF file
generation.
Exercise 1: PCF Files Generation
The Project Configuration tool enables you to specify if a PCF file will be
generated with an Isometric drawing or not. If the Allow PCF File Generation
value is set to True a PCF file will be generated. If it is to False a PCF file will
not be generated.
This exercise will show you how to configure Isometric Manager to generate a
PCF file.
1 Select Tools > Configuration or click the Configuration icon.
2 Select Project.
3 Expand the PCF Generation Section window.
4 Select True from the Allow PCF File Generation field, if not already
selected.
Note: False doesn't allow PCF file generation.
Another parameter which can be set for a project by the Isometric
Configuration tool is called Can Post PCF to ProjectWise. The value specified in
this field enables or disables sending generated PCF files to ProjectWise. If the
Can Post PCF to ProjectWise value is set to True a PCF file will be posted to
ProjectWise together with a generated Isometric drawing. If it is set to False a
PCF file will not be sent to ProjectWise.
5 Select True from the Can Post PCF to ProjectWise field, if not already
selected.
The last value to be set in the PCF Generation section is Stop Isometric
Generation if PCF Fails.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
67/86
Jul-11 67 Management of PCF filesCopyright © 2011 Bentley Systems, Incorporated
Generate PCF files for passing data to legacy systems
If the value specified in this field is set to True an error during a PCF file
generation will cause termination of an Isometric drawing generation.
If the value specified in this field is set to False an error during a PCF file
generation does not influence an Isometric drawing generation.
6 Select True in the Stop Isometric Generation if PCF Fails field.
7 Click Save.
8 Click Close.
The Isometric Configuration dialog is closed.
Exercise 2: Viewing and exporting of a PCF Files
1 Select an Isometric drawing, right-click and select PCF File.
Note: Create a new Isometric drawing before step 1 if none is currently
available in the Isometric Manager.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
68/86
Management of PCF files 68 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Generate PCF files for passing data to legacy systems
2 The PCF file connected to the selected Isometric drawing is opened in
Notepad. You can browse through it now.
3 Select File > Exit.
Notepad closes.
4 Select an Isometric drawing again, right-click and select the Post to
ProjectWise.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
69/86
Jul-11 69 Management of PCF filesCopyright © 2011 Bentley Systems, Incorporated
Generate PCF files for passing data to legacy systems
5 Launch ProjectWise Explorer and navigate to your folder
Training_Isometrics.
6 Select the last generated pcf file, right-click and select Export.
The Document Export Wizard starts.
7 Click Next.
The following dialog opens.
8 Set Send to Folder - create an unmanaged local copy.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
70/86
Management of PCF files 70 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Generate PCF files for passing data to legacy systems
9 Click Browse.
To navigate to the target folder.
10 Click Next.
11 Click Finish.
Note: The PCF configuration file Pcf.ini is located in the same directory as
other Isometric Style configuration files, for example for the Isometric
Style IFC is found in C:\ProgramData\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Style
s\IFC\Config\.
Note: Customization of a PCF output is outside of the scope of this course.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
71/86
Jul-11 71 Management of PCF filesCopyright © 2011 Bentley Systems, Incorporated
Module Review
Module Review
Now that you have completed this module, let’s measure what you have learned.
Questions
1 True/False: PCF files are intermediate files created during an Isometric
Drawing production.
2 True/False: PCF files are automatically generated together with Isometric
Drawing files.
3 True/False: Creation of a pcf file and generation of an Isometric Drawing
are independent activities and do not influence each other.
Answers1 False: The Isometric Manager creates a PCF file as a by-product during an
Isometric Drawing generation. These PCF files can be used by other
applications.
2 False: PCF files are automatically generated together with Isometric
Drawing files but only if the attribute Allow PCF File Generation is set to
True. The value False doesn't allow PCF file generation.
3 False: Pcf files and Isometric are created independently but there is
available an attribute Stop Isometric Generation if PCF Fails. If it is set to
True an error during a PCF file creation causes termination of an IsometricDrawing generation.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
72/86
Management of PCF files 72 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Module Review
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
73/86
Jul-11 73 Course Summary
Copyright © 2011 Bentley Systems, Incorporated
Course Summary
Course Summary
You have now completed the course and are prepared to customize Isometric
drawings to meet corporate standards.
Now you will be able to:
• Use the Isometric Configuration tool.
• Customize drawing attributes for additional pipeline information.
• Setup drawing layout and Bill of Material definitions.
• Customize existing and create new custom isometric symbols.
• Set Isometric Revision Format.
• Set connection to ProjectWise for deliverables Management.
• Allow PCF File Generation.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
74/86
Course Summary 74 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Course Review
Course Review
Now that you have completed this course, let’s measure what you have learned.
Questions
1 True/False: The engine used by Isometric Manager to create Isometric
Drawings is called Isogen.
2 True/False: To be able to create an Isometric Drawing OpenPlant
Isometric Manager has to be connected to the ModelServer.
3 True/False: When generating an Isometric Drawing you can select which
Isometric Style will be used by the Isometric Manager.
4 True/False: One Design State can be mapped to several Isometric Styles.
5 True/False: Revisions are assigned to Isometric Drawings based onIsometric Revision setting specified for each Design State.
6 True/False: A revision is set to an Isometric Drawing at the momet you
send it to ProjectWise.
7 True/False: Design States Color specifies a color used to display Iso Sheets
in the Isometric Manager window.
8 True/False: Drawing Attribute Collection is limited to 32 drawing
attributes.
9 True/False: Mapping between text nodes and Drawing Attributes is
defined in the Openplant_3d_supplemental_isometrics_isoextractor
schema.
10 True/False: Assignment of OpenPlant Components to names of iso
symbols used by Isometric Manager is done in isoextract.dat file.
11 True/False: When an Isometric Drawing is created and put into
ProjectWise the Design State of the components used to create an
Isometric Drawing can be automatically changed. A result Design State is
defined by the Completed Isometric Design State value specified for a
project using Isometric Configuration tool.
12 True/False: One of parameter which can be set for a project by the
Isometric Configuration tool is called Can Post PCF to ProjectWise. Thevalue specified in this field enables or disables sending generated PCF files
to ProjectWise.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
75/86
Jul-11 75 Course SummaryCopyright © 2011 Bentley Systems, Incorporated
Course Review
Answers
1 False: The engine used by Isometric Manager to create Isometric Drawings
is called IsoExtractor.
2 False: The Isometric Manager can work in two modes. You can be
connected to the ModelServer and take data for Isometric Drawing fromthere or to generate Isometric Drawings from imported i-models.
3 False: An Isometric Style to be used for an Isometric Drawing creation is
selected automatically based on Design State mapping.
4 False: The same Isometric Style can be mapped to several Design States
but to a Design State you can be mapped only to one Isometric Style.
5 True: Revisions are assigned to Isometric Drawings based on Isometric
Revision setting specified for each Design State. If no specific Isometric
Revision format is specified for a used Design State, system uses
Isometric Revision format set for a Project. Isometric Revision format set
for a Design Stage has a priority
6 False: A revision is set to an Isometric Drawing during its creation. System
checks (in ProjectWise) the last revision of just generated Isometric
Drawing and assigns the following one.
7 True: Design States Color specifies a color used to display Iso Sheets in the
Isometric Manager window. It helps to distinguish groups of iso sheets in
the same Design State
8 False: By default there are available 32 attributes for each Isometric Style
to be used on an Isometric Drawing anyway you can add another drawing
attributes if required. Each so called Drawing Attribute Collection isspecified by the NAME and by the VALUE.
9 False: Mapping between text nodes and Drawing Attributes is defined in
the file node2da.txt located for example for the OPModeler_Metric
project and As-Built Isometric Style in the folder
...\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\
As-Built\Config.
10 False: Assignment of OpenPlant Components to names of iso symbols
used by Isometric Manager is done in
Openplant_3d_supplemental_isometrics_isoextractor schema.
11 False: When an Isometric Drawing is created and put into ProjectWise the
Design State of the components used to create an Isometric Drawing can
be automatically changed. A result Design State is defined by the
Completed Isometric Design State value which is specified not for the
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
76/86
Course Summary 76 Jul-11Copyright © 2011 Bentley Systems, Incorporated
Course Review
whole project but for each Isometric Style separately. To change a
predefined value you can use the Isometric Configuration tool.
12 False: Isometric Manager does not enable to post LOG files to
ProjectWise. One of parameter which can be set for a project by the
Isometric Configuration tool is called Can Post PCF to ProjectWise. The
value specified in this field enables or disables sending generated PCF filesto ProjectWise.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
77/86
Jul-11 77 Appendix A
Copyright © 2011 Bentley Systems, Incorporated
Appendix A
rep_sortgroups.txt
The file location:
C:\Documents and Settings\All Users\Application
Data\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\As-
Built\Config\
#-----------------------------------------------------------------------------
#
# Define:
# - sort groups
# A sort group specifies a group of elements that have more or less equal
# precedence in the BOM report
# - sort group headers
# - distribution of components over the sort groups
#
# Sort groups determine how part ID's are distributed among the components in
# the isometric,
# - the sort groups provide a mechanism to group logically related components
# (like:FLANGES, VALVES)
# - sort groups have different priorities. The hight the priority the
# lower the part ID's of the components in the group will be
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
78/86
Appendix A 78 Jul-11Copyright © 2011 Bentley Systems, Incorporated
rep_sortgroups.txt
# - components in the same sort group get sequential PART ID's
#
# The specification for a sort group is like:
#
# SORTGROUP = sort group name, free to choose
# HEADER = specification for header line in report when SORTHEADERS = 1 is
# specified in the report definition. One can speciy up to 10
# lines. Normally leading and trailing spaces are trimmed, one can
# use a '@' as placeholder for a space
# RULE = Specifies a regular expression (regex) on the attributes of a
# component. If the rule evaluates to true the component is added
# the sortgroup. Multiple RULE lines can be specified, any rule that
# evaluates to true makes the component part of the sort group
#
# - One can define up to 50 sort groups
# - the rules within a sortgroup defined the ordering within the sort group.
# the earlier a rule is satisfied, the lower the partID will be
# - The sort group order is the order in which the sort groups are defined
# we probably will add an explicit ORDER= line
#-----------------------------------------------------------------------------
SORTGROUP = PIPES
HEADER = @ -----------
HEADER = @ PIPES
HEADER = @ -----------
RULE = IE_TYPE=CT_PIPE
RULE = IE_TYPE=CT_BEND
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
79/86
Jul-11 79 Appendix ACopyright © 2011 Bentley Systems, Incorporated
rep_sortgroups.txt
SORTGROUP = GASKETS
HEADER = @ -----------
HEADER = @ Gaskets
HEADER = @ -----------
RULE = IE_TYPE=CT_GASKET
SORTGROUP = BOLTS
HEADER = @ -----------
HEADER = @ Bolts
HEADER = @ -----------
RULE = IE_TYPE=CT_BOLT
# this is the dump sortgroup for all the component not specifically assigned
SORTGROUP = OTHER
HEADER = @ -----------
HEADER = @ Not yet grouped
HEADER = @ -----------
RULE = IE_TYPE=CT_.*
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
80/86
Appendix A 80 Jul-11Copyright © 2011 Bentley Systems, Incorporated
rep_sortgroups.txt
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
81/86
Jul-11 81 Appendix B
Copyright © 2011 Bentley Systems, Incorporated
Appendix B
report.def
The file location:
C:\Documents and Settings\All Users\Application
Data\Bentley\OpenPlantModeler
V8i\WorkSpace\Projects\OPModeler_Metric\DataSet\Isometrics\Styles\
As-Built\Config\
#-----------------------------------------------------------------------------
#
# Report definition file
#
# This file contain the defintions for all reports produced by IsoExractor.
#
# IsoExtractor reports are generic reports that operate on component attributes
# Reports generated are plain text files that can be attached to a text node in the
# drawing. A report definition is a combination of specification and a script.
#
# REPORT = Specifies the extension given to the report. The basename
# of the report is the same as the isometric DGN, the report is written
# to the IE_REPORTDIR directory
#
# INCLUDE = Provides a rule which components are to be included in the report. The
# rule operates on the component attributes. There can be multiple
# INCLUDE lines. Any INCLUDE line satisfied includes the component in the
# report
#
# EXCLUDE = same as INCLUDE but this time to specify that a component should not
# be in the report. Multiple EXCLUDE lines are allowed. Any EXCLUDE
# line satisfied excludes the component from the report.
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
82/86
Appendix B 82 Jul-11Copyright © 2011 Bentley Systems, Incorporated
report.def
#
# COLUMN = : :
#
# Specifies a column in the report, consists of three fields separated
# by a colon character.
#
# specifies the width of the column in character positions
#
# a combination of:
# L left aligned
# R right aligned
# C centered
# W wrap, a new line will be added if the length of the expression
# exceeds the width of the report
#
# An expression for the content of the report column. Any component
# attribute or string can be used. Example:
# IE_DESCRIPT + UUID + "and a string"
# would concatenate the atributes IE_DESCRIPT and UUID and the string
# "and a string"
#
# SEP = column separator. Can be any combination of characters, a '@' is used
# as a space placeholder. The default SEP is the empty string
#
# NODE = specifies the text node number in the isometric the report will be
# attached to
#
# SORTHEADERS = specifies if sort group headers are to be used (see: rep_sortgroups.txt)
# 1 = use sortgroup header
# 0 = dont
#
# TEXT = Specifies a line to be written to the report. '@' acts as a placeholder for a
space
#
# WRITE = Write this or another report. When empty the report is written according to
# the COLUMN, INCLUDE, etc statements
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
83/86
Jul-11 83 Appendix BCopyright © 2011 Bentley Systems, Incorporated
report.def
# When a report extension is specified than that report is included
#
# GROUP = a list of attributes that defined which component are grouped together
# thus using the same line in the report (increasing the quantity). Attributes
# are comma separated
# SORT = sort the list on a set of attributes value. Consiste of a comma separated list
# of attributes with an optional descending/ascending order. Example:
# SORT =
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
84/86
Appendix B 84 Jul-11Copyright © 2011 Bentley Systems, Incorporated
report.def
INCLUDE = IE_FIELD=0
COLUMN = 3: R : PARTID
COLUMN = 19: R : QUANTITY
COLUMN = 7: R : SIZE1
COLUMN = 7: R : SIZE2
COLUMN = 2: :
COLUMN = 30: W : IE_DESCRIPT
COLUMN = 30: : IE_ITEMCODE
GROUP = PARTID
SORT = PARTID:N
SEP = @
SORTHEADERS = 1
TEXT = @ ----------------------------------------------------------
TEXT = @ Shop Materials
TEXT = @ ----------------------------------------------------------
Write =
END
#-----------------------------------------------------------------------------
# A sample report that writes field material to a report
# Defintion is the same as for the SHP report except for the INCLUDE line
#-----------------------------------------------------------------------------
REPORT = FLD
# this to include only field items
INCLUDE = IE_FIELD=1
COLUMN = 3: R : PARTID
COLUMN = 19: R : QUANTITY
COLUMN = 7: R : SIZE1
COLUMN = 7: R : SIZE2
COLUMN = 2: :
COLUMN = 30: W : IE_DESCRIPT
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
85/86
Jul-11 85 Appendix BCopyright © 2011 Bentley Systems, Incorporated
report.def
COLUMN = 30: : IE_ITEMCODE
GROUP = PARTID
SORT = PARTID:N
SEP = @
SORTHEADERS = 1
TEXT = @ ----------------------------------------------------------
TEXT = @ Field Materials
TEXT = @ ----------------------------------------------------------
Write =
END
#-----------------------------------------------------------------------------
# The COMBI report combine the SHP and FLD report into a single report
# and attaches it to textnode 60 in the isometric
#-----------------------------------------------------------------------------
REPORT = combi
WRITE = shp
TEXT = @
TEXT = @
WRITE = fld
NODE = 60
END
#-----------------------------------------------------------------------------
# The CUT report lists the pipe cut pieces
# Attaches to text node 61
#-----------------------------------------------------------------------------
REPORT = CUT
INCLUDE = IE_TYPE=CT_PIPE|CT_BEND
COLUMN = 6:C:CUTID
COLUMN = 7:R:SIZE1
COLUMN = 21:R:QUANTITY
COLUMN = 3:R:
8/17/2019 OpenPlant Iso Manager Project Admin Training V8i SS3
86/86
report.def
COLUMN = 80:W:IE_DESCRIPT
GROUP = CUTID
SORT = CUTID
NODE = 61
END