Post on 31-Dec-2021
transcript
Operation Manual| VOLTI Go IC-CPD Portable Charger
Operation Manual| VOLTI Go IC-CPD Portable Charger
2
Contents 1. General Information .............................................................................................................................................................................................................. 3
2. Portable Charger (IC-CPD) Overview ................................................................................................................................................................................... 3
3. Document Legends .............................................................................................................................................................................................................. 4
4. Safety Pictograms ................................................................................................................................................................................................................ 4
5. Instructions for Safety ........................................................................................................................................................................................................... 5
6. Ways to Prevent Damage ..................................................................................................................................................................................................... 6
7. Charger Features ................................................................................................................................................................................................................. 7
8. LED Display .......................................................................................................................................................................................................................... 8
9. Using your Charger .............................................................................................................................................................................................................. 8
10. Troubleshooting your Charger ........................................................................................................................................................................................... 8
11. State and Fault Identification ............................................................................................................................................................................................. 9
12. Caring for your Charger .................................................................................................................................................................................................. 10
13. Disposal of your Charger ................................................................................................................................................................................................ 10
14. Warranty ......................................................................................................................................................................................................................... 10
15. Technical Specifications .................................................................................................................................................................................................. 11
16. Service Information ......................................................................................................................................................................................................... 11
About this manual This Operation Manual document is written and covers for the VOLTI Go IC-CPD Portable Charger product at the time of publication. Without prior notice,
VOLTI reserves the right to modify the product information. The product is sold as is. Any changes or modifications carried out by any party that is not an
approved service workshop of VOLTI may result in loss of warranty. Please refer to this manual or get in contact with VOLTI representatives for your
questions regarding the use of this product.
This document provides the information that is essential for safely installing, operating and maintaining VOLTI Charging Station. Please make sure to read
and understand all the instructions, follow the procedures fully and in correct order. Always keep this document in a safe place that is easy to access.
Version Date Description
0.1 15.10.2020 First Draft
Operation Manual| VOLTI Go IC-CPD Portable Charger
1. General Information This User Manual document is written and
covers for the product at the time of publication.
Without prior notice, Volti reserves the right to
modify the product information. The product is
sold as is. Any changes or modifications carried
out by any party that is not an approved service
workshop of Volti may result in loss of warranty.
Please refer to this manual or get in contact
with Volti representatives for your questions
regarding the use of this product.
VOLTI Electric Vehicle Charging Systems
info@volti.com | www.volti.com
Büyükkılıçlı Mah.
Hançer Sokak No:16 34570
Silivri - Istanbul - TURKEY
+(90) 212 549 0555 Pbx
2. Portable Charger (IC-CPD) Overview VOLTI Go In-Cable-Control-and-Protection-Device (IC-CPD) Portable Charger consists of the following components:
You can use the wall hanger part to hang your
VOLTI Portable IC-CPD Charger to keep it
safe, out of reach and stationary during
charging.
Wall hanger apparatus can be attached and
detached according to your preference.
Operation Manual| VOLTI Go IC-CPD Portable Charger
4
3. Document Legends
⚠ DANGER
This sign means imminent danger. Not
following this instruction will result in serious
injury even death.
⚠ WARNING This sign means possible danger. Not following
this instruction may result in serious injury
even death.
⚠ CAUTION This sign means dangerous situation. Not
following this instruction may result in minor
injury.
4. Safety Pictograms
Instruction Handle with Care Caution! Caution! Caution!
Always follow the instructions Be careful while operating your charging device
High voltage Hot surface Obstacle in the way
DO NOT: DO NOT:: DO NOT:: DO NOT:: DO NOT::
Don’t leave under direct sunlight or cover the device
Don’t submerge in water, spray or splash water
Don’t use with multiple sockets or adapters
Don’t use with extension cords, extension cables
Don’t bend, twist the cables
DO NOT: DO NOT: DO NOT: DO NOT: DO NOT:
Don’t contact with snow or ice Don’t use while power cable is coiled. Charging cable is
coiled on purpose.
Don’t run over the cables, power plug, charging plug or
control box
Don’t use if any part is damaged
Don’t perform any repairs on the charging device or its
parts. Never open the device.
Don’t unplug your charging device during charging
Make sure the ambient temperature is within the operating range before
starting charging
Operation Manual| VOLTI Go IC-CPD Portable Charger
5. Instructions for Safety
⚠ DANGER
Electric Shock & Fire Hazards
If the socket used for charging is incorrectly
installed, this can lead to electric shock or fire
when charging the vehicle. Please make sure:
IC-CPD Power Plug is only connected
to Socket that is part of a grounded
power network.
The Socket to which charger is
connected via Power Plug must be
connected to a protected circuit required
by the law and standards of your region.
The Socket must be protected by a
suitable current-operated residual circuit
breaker (RCCB).
The charging is done according to this
manual and also the manual provided
with your vehicle.
If the charging cable is damaged
or faulty or the socket used is
damaged or faulty, or the portable
charging equipment is used
improperly and incompliant with the
precautions mentioned in this
document, it can cause electric shock,
short-circuits, fire, and burns. Please
make sure:
Do NOT use the IC-CPD charger if the
product is damaged or soiled. Before
each use, please check the cables,
connector and the control box for any
damages.
Never use the IC-CPD charger with a
worn-out socket. Make sure the socket
used for charging is firmly seated and it
is in accordance with the law,
regulations and standards.
USING THE IC-CPD CHARGER WITH
IMPROPPER SOCKETS CAN LEAD
TO SRIOUS INJURY OR FIRE!
Under no circumstances IC-CPD
charger shall be opened by the user.
Device is NOT serviceable by any other
party than the ones approved by VOLTI.
Do NOT touch the parts inside the
vehicle connector.
Please makes sure that the voltage
used with the device is in accordance
with the rated voltage of the IC-CPD
charger. Only use the device with the
suitable sockets. See the back of the
device for more information regarding
rated energy requirements and
compliance.
The charger must be plugged to the wall
socket directly. Do NOT use any
extension cords, cables, cable drums,
multiple sockets, travel and other sorts
of adapters, timers etc.
Never perform any repair tasks,
servicing and modification to electrical
components and do NOT open the
device.
Do NOT touch the pins/contacts on the
IC-CPD vehicle connector and vehicle
charging inlet.
Vehicle connector, control box, power
plug and the socket used must be free
of moisture, water, snow, ice and other
liquids. Do NOT immerse the IC-CPD
charger in water.
Do NOT leave the charger plugged to
the socket during a thunderstorm.
Do NOT insert any foreign materials,
objects in to the IC-CPD charger or
vehicle inlet.
Only clean the IC-CPD charger when
the charger is completely disconnected
from the socket (grid) and from the
vehicle inlet. When cleaning, only use
dry cloth.
IC-CPD charger must NOT be operated
by persons under the influence of drugs,
alcohol or medication.
IC-CPD charger must NOT be operated
by persons that are not familiar with the
use of the product or has not read this
manual.
Operation Manual| VOLTI Go IC-CPD Portable Charger
6
IC-CPD charger must be kept away
from persons with disabilities and
children who may not be able to assess
the hazards involved with operating this
product.
During an unattended charging,
unauthorized persons (e.g. children)
should be prevented from accessing the
IC-CPD charger.
⚠ WARNING Fire, Explosion hazards
To ensure that the vehicle has a valid charging
inlet, please refer to the vehicle manual.
IC-CPD charging components may cause
sparks and ignition of flammable or explosive
vapors.
While charging, makes sure the IC-CPD
charger is located 50 cm above the
ground to reduce the risk of explosions,
especially in garages.
If the ambient is potentially explosive,
do NOT use the IC-CPD charger.
IC-CPD charger is designed to charge
electric vehicles that do NOT require
ventilation while charging.
6. Ways to Prevent Damage Follow these instructions below to prevent your
charger from getting damaged.
Prevent IC-CPD charger from sliding
over sharp edges.
Prevent the cables from bending
sharply.
Do NOT drive over the IC-CPD charger
control box, plug, connector and cables.
Handle with care and do NOT exert
extreme force on the product.
Do NOT use the IC-CPD charger
outside the intended operating
temperature range of the product: -13°F
(-25 °C) to 122 °F (+50 °C)
Operating outside of these temperature
ranges may damage the IC-CPD
charger.
Make sure the IC-CPD charger is used
with the same type of socket outlet and
vehicle inlet.
Only operate the IC-CPD charger as
directly connected to the fixed grid
socket outlet.
Improper use outside of what is
described in this user manual may result
in malfunction of the product and
damage to properties.
This portable IC-CPD charger is an
electric vehicle supply equipment
(EVSE) and is suitable to charge
battery-powered electric vehicles (BEV)
and plug-in hybrid electric vehicles
(PHEV).
VOLTI Portable IC-CPD Charger allows safe
and easy to use charging (mode 2) for the
owners of electric vehicles. The charger allows
direct charging from any suitable socket with
supply voltage of 100V to 230V AC.
Operation Manual| VOLTI Go IC-CPD Portable Charger
7
7. Charger Features VOLTI IC-CPD Portable Charger is equipped
with various safety and functional features.
Safety Features
Leakage current detection
Overvoltage detection
Overcurrent detection
Temperature detection
Ground monitoring
o This features prevents charging
from power grids without
protective conductor.
Charging circuit breaker system
Functional Features
Wall-hanger for everyday use. When
needed, VOLTI IC-CPD can be
detached from the wall and is ready to
travel with you wherever you may go.
Suitable for both indoor and outdoor
use.
LED display with icons allows for easy
operation and troubleshooting.
Additional Features
VOLTI IC-CPD Portable Charger allows you to
charge your battery-powered electric vehicle
(BEV) or plug-in hybrid electric vehicle (PHEV)
by itself, without requiring any additional device.
Out of the box, VOLTI IC-CPD Portable
Charger fits to your regional electric socket
outlet and directly to your electric vehicle
charging inlet. The ergonomic vehicle
connector allows you to easily plug-in to your
electric vehicle. The spiral charging cable
makes it easier to store and reduces the cable
damage especially when the VOLTI IC-CPD
Portable Charger is hanging via the wall
hangers.
VOLTI IC-CPD Portable Charger allows
charging from standard grounded residential
sockets from 100V to 230V AC (50/60Hz) and a
charging current 6A up to 16A depending on
the regional specifications of the unit sold.
Vehicle Cable, Connector, Power Plug
IEC 62196-1 - Plugs, socket-outlets, vehicle
connectors and vehicle inlets – Conductive
charging of electric vehicles –Part 1: General
requirements
IEC 62196-2 - Plugs, socket-outlets, vehicle
connectors and vehicle inlets – Conductive
charging of electric vehicles –Part 2:
dimensional compatibility and interchangeability
requirements for A.C. pin and contact-tube
accessories
Ergonomic rubber grip for optimal support
Halogen-Free cable structure
Type 2 Vehicle Connector suitable for use in
European Countries.
Power Plug type CEE 7/7Type E/Type F
“SchuKo”
In-Cable Control and Protection Device
IEC 61851-1 Electric vehicle conductive
charging system – Part 1: General
requirements
IEC 62752 In-cable Control and Protection
Device for Mode 2 Charging of Electric Road
Vehicles (IC-CPD)
Ground Monitoring
Electromechanical circuit breaking
against electric shock
Self-test before each charging session
Automatic recovery after error detection
if the error situation is corrected
Continuous temperature monitoring
against overheating
Operation Manual| VOLTI Go IC-CPD Portable Charger
8
8. LED Display LED display on the front of the VOLTI Portable
IC-CPD Charger shows the current state of
your charger. The four LEDs represent the
following:
1- POWER – VOLTI Portable IC-CPD
Charger is plugged in to the grid and is
powered. Your charger is ready to use.
2- CHARGING – Your electric vehicle is
being charged.
3- GROUND FAULT – The grid connection
(power socket outlet) doesn’t have
proper grounding. In this case, please
unplug your charger and use a grid
connection with proper grounding.
Charging will NOT take place.
4- FAULT – Indicates a failure of VOLTI
Portable IC-CPD Charger.
For more information about
troubleshooting the fault condition,
please see the
Troubleshooting your Charger section of
this manual.
9. Using your Charger To operate your charger safely and properly,
please follow the steps below:
1- Read and understand the manual of
your electric vehicle and VOLTI Portable
IC-CPD Charger before using your
charger.
2- Make sure that the cables are uncoiled
and routed correctly to avoid any
tripping.
3- Insert the power plug into the power
socket directly. (Never use extension
cords, timers, additional wires etc.)
4- When the power is properly connected,
POWER LED will light up.
5- Insert the vehicle connector to the
charging inlet of your vehicle.
6- The charging will start automatically.
CHARGE LED will light up.
7- To stop the charging process, unlock
your vehicle’s charging inlet lock and
remove the vehicle connector from the
vehicle’s charging inlet.
8- When you are done with charging
remove the power plug from the power
socket.
9- Store your VOLTI Portable IC-CPD
Charger safely.
10. Troubleshooting your Charger If the FAULT LED flashes 2 times followed by a
short break:
1- Remove the vehicle connector of your
charger from your electric vehicle’s
charging inlet.
2- Unplug your charger from the power
socket.
3- Wait for 10 seconds.
4- Insert the power plug of your charger
into the power socket.
5- Wait for the POWER LED to light up.
6- Insert the vehicle connector into your
vehicle’s charging inlet.
7- The charging will resume automatically.
AFTER FOLLOWING THESE STEPS, IF THE
FAULT LED FLASHES CONTINUOUSLY
DURING OR AFTER CHARGING, DO NOT
USE THE DEVICE AND CONTACT
CUSTOMER SERVICE. (See Service section
of this manual).
Operation Manual| VOLTI Go IC-CPD Portable Charger
11. State and Fault Identification For troubleshooting various faults that can occur please refer to the following table:
State and Fault Definition
◌ ◌ ◌ ◌ No power is reaching to your charger.
● ◌ ◌ ◌ VOLTI Portable IC-CPD Charger is ready to use
● ◌● ◌ ◌ Vehicle connected
● ● ◌ ◌ Charging in progress
●◌ ◌● ●◌ ◌● Self-test in progress
● ◌ ● ◌ No ground detected. Charging won’t start. Please plug your charger to a grounded power socket.
Minor Faults
VOLTI Go encountered a minor fault. Charging will be limited. Charging times may be longer.
● ● ◌ ◌● Slow charging in progress due to high temperature. Charging may take longer.
● ● ◌ ● Charging stopped due to high temperature. Check your device and make sure to remove your charger from direct sunlight.
Critical Faults
VOLTI Go encountered a critical fault. 1- Disconnect charging plug from vehicle inlet. 2- Unplug your VOLTI Go from electric outlet and re-plug. 3- After self-test. İf ERROR LED turns red, unplug your charging device and follow the instructions below: Try using your VOLTI Go charging device with another electric outlet. If problem persists, please contact a qualified electric technician.
● ◌ ◌ ● System fault – Please contact your VOLTI sales channel
●◌ ◌ ◌ ● Grid malfunction detected
● ◌ ●◌ ● Critical leakage current detected
◌ LED OFF ● LED ON ◌● LED BLINKING
Operation Manual| VOLTI Go IC-CPD Portable Charger
12. Caring for your Charger
⚠ DANGER
Electric Shock & Fire Hazards WARNING! To avoid electric shock and
damage to your charger, clean your charger’s
plug and housing with caution.
Clean VOLTI Portable IC-CPD
Charger only with a dry cloth.
Never use any cleaning agents or
flammable solvents such as
benzene and alcohol.
Any contact with chemicals is prohibited and
can damage the device.
⚠ CAUTION Any changes or modification made to the
product without the approval and supervision of
VOLTI authorized service will result in the loss
of product regulatory compliance, void of
product warranty and is strictly forbidden.
13. Disposal of your Charger While disposing your VOLTI Portable IC-CPD
Charger, you must comply with
the local-law and guidelines of
your region. Product and batteries
must never be disposed of with
domestic waste.
Product must be
disposed of at an electronic waste
collection facility or your local VOLTI
dealer.
Dispose of product packing material
according to the type of the material
(e.g. plastic, carton, paper)
14. Warranty VOLTI ensures that the product will be free
from material and workmanship related defects.
Also the product will be free from design errors
for one (1) year from the original purchase date.
If the product is deemed to be defective in
construction, manufacturing or material while in
the warranty period, VOLTI will, at its discretion,
replace or repair the product. At VOLTI’s
discretion, the repaired parts and/or
replacement products can be of either new or
refurbished products.
Improper installation, incorrect connection of
peripherals, external electrical interference,
accident, disaster, misuse or any and all
changes made to the product that are not
approved with a written notification of VOLTI.
Any service and repairs outside of the warranty
period and conditions, shall be performed at the
rates, terms and conditions that are in effect at
the time of repair.
Any other implied or expressed warranties in
relation to this product, including but not limited
to the warranty of general suitability and fitness
for a particular purpose, are hereby excluded.
In some regions / countries, such exclusion of
implied warranties are not permitted. For these
regions / countries, the above statement may
not apply.
If the product is in non-compliance with the
above mentioned warranty, you are entitled to a
full replacement or repair of the defective
product. Under no circumstances shall VOLTI,
a sales and/or service representative or the
parent company be held accountable to the
customer or any other third party for any
damages that exceed the purchase price of the
product. This limitation also applies to damages
of any kind, including any direct or indirect
damages, loss of profits, loss of savings or
special incidental damages, punitive of
consequential damages, whether it be caused
by a breach of a contract, tort or any other
means, or if such damages are based on the
use or improper use of the product, even if
VOLTI or an authorized representative or
dealer of VOLTI has been advised by third
parties about the possibility of such damages or
any other claim.
In some regions / countries, such exclusion of
incidental or consequential damages is not
permitted for some products. For these regions
/ countries, the above statement may not apply.
With this warranty you obtain specific legal
rights. Depending on your county, you may
have other rights as well.
For more information, you can contact
VOLTI customer service.
Operation Manual| VOLTI Go IC-CPD Portable Charger
11
15. Technical Specifications
Part number EVP.16.1.6.1
Rated current Default 10A Max. 16A
Rated voltage 230V AC
Rated frequency 50 / 60Hz
Rated op. residual current AC 30mA AC
Rated op. residual current DC 6mA DC
IP degree of protection IP69 (Charge control box) IP 44 (Cable and vehicle connector)
Device dimensions width x height x depth ; total length Box (8.7 cm x 27 cm x 5.2 cm); 7 meters total working length
Device weight Charge control box 1.96 kg
Operating temperature -25 °C to +50 °C
Storing temperature -30 °C to +70 °C
Humidity Up to 95%, non-condensation
Altitude 2000 meter and below
Standards This IC-CPD charging equipment meets
all applicable IEC and EN standards and
regulations in the context of national
legislation, as well as the European and
inter- national regulations. If necessary,
the respective declaration of conformity
can be made available
16. Service Information Please contact your local sales channel for support.