Order No. PHAT090901C3 Service Manual - Panasonic...Order No. PHAT090901C3 Service Manual(Revision :...

transcript

Order No. PHAT090901C3(Revision : Mar. 2013)

Service ManualFully Automatic Washing Machine

NA-FS80X1NA-FS90X1

Product ColourWhite

DestinationThailand, Malaysia, Indonesia

Vietnam, PhilippinesSingapore (DBD)Singapore (RBD)

There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Diagrams, Exploded Views and Replacement Parts List. It is essential thatthese critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Donot modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

WARNINGThe service information is designed for experienced repair technicians only and is not designed for use by the generalpublic. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attemptingto service a product. Products powered by electricity should be serviced or repaired only by experienced professionaltechnicians. Any attempt to service or repair the product or products dealt within this service information by anyoneelse could result in serious injury or death.

CONTENT

8 - 1920 - 21

22 - 2324 - 25

272828293031

343536373839404041

1. Attention in the Repair Work Security 2. Specification 3. Technical Information 3.1 Eco-Wash Systems 4. Operation Panel 4.1 Control Panel and Functions 4.2 Basic Operations and Indications 5. Program Sequences 6. Installation 7. Table of Errors 7.1 Services Check 7.2 Standard Self-diagnose Functions (Abnormal Information) 7.3 Troubleshooting of H25, H26 8. Disassembly • Assembly Instruction 8.1 Controller Display 8.2 Door Lock Switch 8.3 Load Controller 8.4 Water Supply Valve • Bath Pump • Water Level Sensor • Lid Switch 8.5 Bearings (Mechanical Motor) 9. External Dimension Figure10. Circuit Diagram 10.1 Electric Circuit Diagram 10.2 Controller Input • Output Measurement11. Parts Exploded View and Replacement Parts List 11.1 Parts Exploded View : Part A 11.2 Replacement Parts List : Part A 11.3 Parts Exploded View : B 11.4 Replacement Parts List : Part B 11.5 Parts Exploded View : C 11.6 Replacement Parts List : Part C 11.7 Parts Exploded View : Packing Part 11.8 Replacement Parts List : Packing PartDetail Change Notice

NA-FS80X1 / FS90X1

1. ATTENTION IN THE REPAIR WORK SECURITY

NA-FS80X1 / FS90X1

In order to prevent any accident during repair work and ensure security of the product after repair work,somethings surely followed are explained below.

Connectionof cables should be done according to regular work.• Connectionof cables should be tightened reliably with strength using solderless terminal. (specified parts always using regular bonding plier)• Install a fire protection cover (fireproof) covering connectin area completely, and close opening areas by tape. (Please reuse the fire protection cover which came with the products).• When drawing cables around, fixing those cables with cable suppression part. Do not touch rotating part, high temperature part and surface of metal.• Be sure to replace with cable unit when any cable was snapped. When a part of the cable unit was cut, you must not do the connection repair. It may be the cause of smoke, ignition or receiving an electric shock.

Please wear gloves when disassembling, replacing and assembling.Always wear gloves to prevent an injury by the metal end face or an electric shock at the time ofthe electricity service

Please be careful to the edges of the metal end face.Wear the working clothes of long sleeves to prevent an injury by the metal end face or pleasework after covering the end face with tape or towel.

Be careful about receiving an electric shock.When doing electric connection servicesuch as voltage measurement, please becareful enough about receiving an electricshock at electric charging parts and cableterminal parts.

■ The level of the arised damages or dangers, when indicated contents are ignored, are classified byfollowing indications and explained.

WARNING

ATTENTION

The content in the column of this indication is“ Be assumed that possibly die or get seriously injured ”.

This figured symbol means caution “ ATTENTION ”

This figured symbol means caution “ PROHIBITION ”

This figured symbol means caution “ INSTRUCTIONS ”

The content in the column of this indication is“ Be assumed that possibly get damages or possibly only damage object occured ”.

■ The level of the arised damages or dangers, when indicated contents are ignored, are classified byfollowing indications and explained.

WARNING

Pull out electric plug when doing repair work.Disassembling, assembling and replacingparts should be done after pulling outelectric plug. Receiving an electric shockor getting an injury may occur.

Rebuilding is prohibited.Do not rebuild machine parts and components when repairing service.It may be the cause of damage or ignition.

Straightly pull out or insert in huasuton terminal.Do not twist it. It may be the cause of damage or ignition.

Slow rotation may also roll in your handsand cause injury.

Be sure to use specified parts.Always use specified parts for the partswith mark in the electric circuitdiagrams and parts list. It may be thecause of smoke, ignition or damage.

Do not touch any rotating object with handunless it stops completely.

ATTENTION

2. SPECIFICATION

NA-FS80X1 / FS90X1

Outer Dimension(W x D x H)

Rate Voltageand Frequency

220V/50Hz

NA-FS80X1

Vietnam

NA-FS90X1

Thailand, Indonesia, VietnamSingapore (RBD)

Singapore (DBD) Singapore (DBD)

Malaysia

Philippines-

Malaysia

599 x 626 x 1026 (mm.)

80~130 r/min

279~360W (Wash with load)

58~83W (Spin with load) 58~83W (Spin with load)

230V/50Hz

230V/60Hz

240V/50Hz

220~240V/50/60Hz

Rate PowerConsumption

270~345W (Wash with load)

Pulsator (r.p.m.)

740 r/minSpin Tub (r.p.m.) / with rated load

Ring when finishing washing or unusualAlarm

HaveFabric Softner Dispensor

HaveAutomatic Power Cut-Switch

Weight (with packing)

Weight (with accessories)

Filter

HaveBleach Dispensor

Checking unbalance / Tub, LidSafety Switch

0.03 to 1 MPa (0.3 to 10 Kgf/cmWater Supply Pressure

46 Kgs

Lid Unit Colour

46 Kgs

41 Kgs41 Kgs

SilverBlue

WhiteBody Colour White

9.0 KgStandard Capacity 8.0 Kg

120 LiterStandard Water Consumption 116 Liter

310 WattsMotor Power 300 Watts

220~240V/50/60Hz

Installation

554 x 598 x 971 (mm.)Body

3. TECHNICAL INFORMATION

NA-FS80X1 / FS90X1

3.1 Eco-Wash System

By adding a difference to number of rotations when pulsator rotates right and left, it provides strong and softcomposition current. Cloths are replaced up and down to rub even for low water.

• A dancing churning current

By rotating a drain tank (tank), water is pushed up through circulation course in a tank (drain tray). to imporve [Water saving circulation system], standard washing quantity of water 116L (NA-FS80X1, FS90X1)is materialized without reducing quantity of circulate water.

• A circulation jet shower

Eco-wash system performs high efficient washing with low water consumption. It is a combination of [Dancing churning current] which controls pulsator carefully to crumple cloths and [Circulation jet shower]which enchances water circulation.

StronglySoftly Stronger turnSoftlySoftlyStronglyThe right and left same strength

To add the strong and softrotation by adding a differenceto number of rotations whenpulsator rotates right and left.

Cloths are rubbed while itreplaced up and down slowly.

A stronger turn is added with constant timing to replace topand bottom cloths.

To keep force of circulation shower,increasing number of rotations of thetank even for low quantity of water.

Same strength for right andleft turn. Clothing are hard tobe replaced up and downbecause number of rotationsare the same for left and rightturn.

Conventional[Churning Current]

[ A Dancing Churning Current ]

New Product

4. OPEATIONS PANEL

4.1 Control Panel and Function

NA-FS80X1 / FS90X1

e “W

he “

” co

• If

ff, th

e “P

ash”

, “T

al , M

NA-FS80X1 / FS90X1

4.2 Basic Operations and Indications

WASH RINSE SPIN DRY

◎：Changeable　× ：Unchangeable

※ 1. “ Ventilation ” and “ Tub Hygiene ” course are not changeable.※ 2. Within the first 2 min for other than “ Intensive ” and “ Tub Hygiene ” course are changeable.※ 3. “ Premium Hnd Wash ”, “ Intensive ” and “ Tube Hygiene ” course are unchangeable.※ 4. During holding operation for other than cloth quantity sensing, “ Tub Hygiene ” course only hold is

changeable.※ 5. “ Intensive “ and “ Tub Hygiene ” are unchangeable.※ 6. Display reservation setting.※ 7. “ Tub Hygiene ” course is unchangeable.

④ Display during Operation

⑤ End of Operation

⑥ Reservation Setting＊Set a time to finish washing.

＊When a child lock has been set, the remaining time display shows [CL].

[On / Off] of the end buzzer (mention in an [Instruction Manual])

• When power supply turns on, a lamp of [ Normal ] and [ Wash • Rinse • Spin ] turns on.

• Flashing a lamp in operating sequence among Wash • Rinse • Spin. Turn off a lamp when a sequence finished.• For Baht water setting, a lamp of [Wash] or [Rinse 1] flashes during bath pump opern. The lamp doesn’t turn off after finished operation.• Intensive lamp flashes during drying sequence of “ Tub Hygiene ” and “ Intensive ” course. Display panel counts down remaining time.

• Press [ Star/Hold ] button to start operations.

• A buzzer sounds and turn off the power ater complete all programs.

• To disable the end buzzer, holding [Start/Hold] button and turn on the power. (Please hold [Start/Hold] button more than 3 seconds)• Confirmed alarm sounds 1 time (Beep Beep) and the end buzzer has been disabled.• To enable the end buzzer, please perform the same operation. (Confirmed alarm sound 2 times)

• After set reservation, press [Start/Hold] button to start.• Display shows setting information for 2 min. after judgement of cloth quantity. Then, shows reservation time (hours).

Turn on the power supply

Change Setting

Water Level

SETTING BUTTONDURING OPERATION

DURING ARESERVATION

DURINGINITIAL

WAITING

Course

Reserve

Bath Water

Intensive

Premium Hand Wash

Start/Hold

Power [Off]

5. PROGRAM SEQUENCES

NA-FS80X1 / FS90X1

0 10 140 0 10 140 0 10 140 0 10 140 0 10 140 0 10 140

l of W

0 25 0 25 0 25 0 25 0 25 0 25

0 15 -43

35 0 15 -43

0 35 -33

200 0 40 -33

200 0 50 -33

200 0 55 -33

0 15 -33

80 0 15 -33

0 40 80 0 40 80 0 40 80 0 40 80 0 40 80

0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 15 80

0 50 170

110 0 15 170

0 21 120 0 21 120 0 21 120

3 51 130 3 51 130 4 1 130 4 36 130 4 44 130 4 44 130

0 32 110 0 32 125 0 32 130 0 32 135 0 32 150 0 32 160

4 32 130 4 32 130 4 42 130 4 56 130 5 4 130 5 4 130

0 25 80 0 25 80 0 25 80 0 25 80 0 25 80 0 25 80

1 58 1 58 1 58 1 58 1 58 1 58

0 22 35 0 22 35 0 22 35 0 22 35 0 22 35 0 22 35

0 10 0 10 0 10 0 10 0 10 0 10

0 49 0 49 0 49 0 49 0 49 0 49

1 0 35 1 0 35 1 0 35 1 0 35 1 0 35 1 0 35

0 10 0 10 0 10 0 10 0 10 0 10

0 49 0 49 0 49 0 49 0 49 0 49

0 40 80 0 40 80 0 40 80 0 40 80 0 40 80 0 40 80

0 80 0 80 0 80 0 80 0 80 0 80

0 10 0 10 0 10 0 10 0 10 0 10

1 49 1 49 1 49 1 49 1 49 1 49

1 55 740 1 55 740 1 55 740 1 55 740 1 55 1 55 740

0 10 35 0 10 35 0 10 35 0 10 35 0 10 35 0 10 35

0 49 0 49 0 49 0 49 0 49 0 48

35 -33

15 15 15 15 15 15

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 5 50 0 5 50 0 5 50 0 5 50 0 5 50 0 5 50

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 15 50 0 15 50 0 15 50 0 15 50 0 15 50 0 15 50

35 35 35 35 35 35*2*1

End Buzzer

Intermittent Spin

Bubble CleanFlooding

Bubble Limit Spin

Bubble LimitIndirect Spin

Rinse Tank

Rotation

Water Supply

PenetrationChurning

Water SupplyTank Rotation

Intermittent Spin

Inertness

Rinse Waterfall

Intermittent Spin

Inertness

Rinse Waterfall

Intermittent Spin

SelectiveComponents

Wash and Stir

Washing TankRotation

Wash and Stir

Stir(Water Jump Detection)

Water Supply

Water SupplyChurning

Water Supply

High DensityChurning

Water Supply

Bubble PenetrationChurning

Water Supply

Bubble Sequence

Tank Rotation

DetergentDissolution

Water Supply

Tank Rotation

AwaitingDetergentInjection

Quantity of ClothJudgement

n 【7

■ ■■

■■

■ ■

■■

★★

■■

Quick Washing

■・・It

・・T

Quick Washing

NA-FS80X1 / FS90X1

0 10 140 0 10 140 0 10 140 0 10 140 0 10 140 0 10 140

l of W

0 25 0 25 0 25 0 25 0 25 0 25

0 15 -43

35 0 15 -43

0 35 -33

200 0 40 -33

200 0 50 -33

200 0 55 -33

0 15 -33

80 0 15 -33

0 40 80 0 40 80 0 40 80 0 40 80 0 40 80

0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 15 80

0 50 170

110 0 15 170

0 21 120 0 21 120 0 21 120

3 51 130 3 51 130 4 1 130 4 36 130 4 44 130 4 44 130

0 32 110 0 32 125 0 32 130 0 32 135 0 32 150 0 32 160

4 32 130 4 32 130 4 42 130 4 36 130 5 4 130 5 4 130

0 25 80 0 25 80 0 25 80 0 25 80 0 25 80 0 25 80

1 58 1 58 1 58 1 58 1 58 1 58

0 22 35 0 22 35 0 22 35 0 22 35 0 22 35 0 22 35

0 10 0 10 0 10 0 10 0 10 0 10

0 49 0 49 0 49 0 49 0 49 0 49

0 15 485 0 15 485 0 15 485 0 15 485 0 15 485 0 15 485

1 0 35 1 0 35 1 0 35 1 0 35 1 0 35 1 0 35

0 10 0 10 0 10 0 10 0 10 0 10

0 49 0 49 0 49 0 49 0 49 0 49

0 20 110 0 20 125 0 20 130 0 20 135 0 20 150 0 20 160

0 20 95 0 20 150 0 20 160 0 20 190 0 20 190 0 20 190

0 22 50 0 22 50 0 22 50 0 22 50 0 22 50 0 22 50

0 12 0 12 0 12 0 12 0 12 0 12130/

0 40 0 40 0 40 0 40 0 40 0 40

0 25 80 0 25 80 0 25 80 0 25 80 0 25 80 0 25 80

0 49 0 49 0 49 0 49 0 49 0 49

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 5 50 0 5 50 0 5 50 0 5 50 0 5 50 0 5 50

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 15 50 0 15 50 0 15 50 0 15 50 0 15 50 0 15 50

35 35 35 35 35 35*2*1

End Buzzer

Intermittent Spin

Churning Without Air

Keep and Churning

Rinse TankRotation

Water Supply

Intermittent Spin

Inertness

Rinse Waterfall

Intermittent Spin

Inertness

Rinse Waterfall

Intermittent Spin

SelectiveComponents

Wash and Stir

Water Supply

Bubble Sequence

Tank Rotation

Water Supply

Tank Rotation

n 【7

■ ■■

■■

■ ■

■■

★★

■■

■ Spi

■■

Quick Washing

■・・It

・・T

Rinse TankRotation

SelectiveComponents

35 170

35 35 85 35 15 35

- 10 -

NA-FS80X1 / FS90X1

■・・It

・・W

・・T

l of W

0 10 140 0 10 140 0 10 140 0 10 140 0 10 140 0 10 140

0 25 0 25 0 25 0 25 0 25 0 25

0 20 110 0 20 125 0 20 135 0 20 130 0 20 150 0 20 160

0 20 95 0 20 150 0 20 160 0 20 190 0 20 190 0 20 190

0 22 50 0 22 50 0 22 50 0 22 50 0 22 50 0 22 50

0 12 0 12 0 12 0 12 0 12 0 12

0 40 0 40 0 40 0 40 0 40 0 40

0 25 80 0 25 80 0 25 80 0 25 80 0 25 80 0 25 80

0 49 0 49 0 49 0 49 0 49 0 49

35 -33

15 15 15 15 15 15

0 40 80 0 40 80 0 40 80 0 40 80 0 40 80 0 40 80

0 80 0 80 0 80 0 80 0 80 0 80

0 10 0 10 0 10 0 10 0 10 0 10

1 55 740 1 55 740 1 55 740 1 55 740 1 55 740 1 55 740

1 48 1 48 1 48 1 48 1 48 1 48

0 10 35 0 10 35 0 10 35 0 10 35 0 10 35 0 10 35

0 49 0 49 0 49 0 49 0 49 0 49

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 5 50 0 5 50 0 5 50 0 5 50 0 5 50 0 5 50

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 15 50 0 15 50 0 15 50 0 15 50 0 15 50 0 15 50

0 35 -33

200 0 40 -33

200 0 50 -33

200 0 55 -33

0 15 -33

80 0 15 -33

0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80

0 21 120 0 21 120 0 21 120

0 51 130 3 51 130 4 1 130 4 36 130 4 44 130 4 44 130

0 32 95 0 32 110 0 32 125 0 32 130 0 32 145 0 32 160

4 32 130

40 32 130 4 42 130 4 36 130 5 4 130 5 4 130

0 25 80 0 25 80 0 25 80 0 25 80 0 25 80 0 25 80

1 58 1 58 1 58 1 58 1 58 1 58

Water Supply

Quick Washing

Wash and Stir

Water Supply

Bubble Sequence

Water Supply

Tank Rotation

□□

★★

□★

■ ■

■■

★★

■■

SelectiveComponents

Rinse TankRotation

SelectiveComponents

PenetrationChurning

Rinse Tank

Rotation

Bubble Cut Spin

Bubble Cut Drain

Bubble Cleanwater Supply

Intermittent Spin

End Buzzer

Rinse TankRotation

Quick Washing

Wash and Stir

Intermittent Spin

Keep and Churning

Intermittent Spin

Water Supply

Keep and Churning

Water Supply

Churning Without Air

- 11 -

NA-FS80X1 / FS90X1

■・・It

□・・W

・・T

er ☆

・・S

, it s

pin【

l of W

0 10 140 0 10 140 0 10 140 0 10 140 0 10 140 0 10 140

0 25 0 25 0 25 0 25 0 25 0 25

0 15 -43

35 0 15 -43

*2 35 35 35 35 35 35

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 5 50 0 5 50 0 5 50 0 5 50 0 5 50 0 5 50

0 30 120 0 30 120 0 30 120 0 30 120 0 30 120 0 30 120

0 15 50 0 15 50 0 15 50 0 15 50 0 15 50 0 15 50

0 35 -33

200 0 40 -33

200 0 50 -33

200 0 55 -33

0 15 -33

80 0 15 -33

0 40 80 0 40 80 0 40 80 0 40 80 0 40 80

0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 85 80 0 15 15 80

0 50 170

110 0 15 170

0 21 120 0 21 120 0 21 120

0 25 80 0 25 80 0 25 80 0 25 80 0 25 80 0 25 80

1 58 1 58 1 58 1 58 1 58 1 58

1 20 35 1 20 35 1 20 35 1 20 35 1 20 35 1 20 35

0 49 0 49 0 49 0 49 0 49 0 49

0 20 110 0 20 125 0 20 130 0 20 135 0 20 150 0 20 160

0 20 95 0 20 150 0 20 160 0 20 190 0 20 190 0 20 190

0 54 130 0 54 130 0 54 130 0 54 130

0 25 80 0 25 80 0 25 80 0 25 80 0 25 35 0 25 35

0 49 0 49 0 49 0 49 0 49 0 49

35 35 35 35 35 35

2 14 260 2 14

130 1 14

130 1 35

130 1 35 15 130

Tank Rotation

Water Supply

☆■

■■

□□

□■■

■■

★★

■■

Tank Rotation

Bubble Sequence

Water Supply

Intermittent Spin

*1Brake

Water Supply

*1Brake

End Buzzer

Intermittent Spin

Rinse Waterfall

Intermittent Spin

SelectiveComponents

Rinse TankRotation

Wash and Stir

Selective ComponentsWater Supply

- 12 -

NA-FS80X1 / FS90X1

■・・It

・・W

・・T

☆・・S

, a ta

, it s

in.】

l of W

0 15 -43

35 0 15 -43

0 30 120 0 30 120 0 30 120 0 30 120

0 5 50 0 5 50 0 5 50 0 5 50

0 30 120 0 30 120 0 30 120 0 30 120

0 15 50 0 15 50 0 15 50 0 15 50

0 40 -33

200 0 50 -33

200 0 55 -33

0 15 -33

80 0 15 -33

0 40 80 0 40 80 0 40 80

0 15 85 80 0 15 85 80 0 15 85 80 0 15 15 80

0 15 170

11 35 195

11 35 175

11 35 100

11 35 15

0 25 80 0 25 80 0 25 80 0 25 80

1 58 1 58 1 58 1 58

2 55 740 2 55 740 2 55 740 2 55 740

35 170

35 100

35 15 35

35 35 35 35

0 25 0 25 0 25 0 25

Tank Rotation

Water Supply

Tank Rotation

Bubble Sequence

Water Supply

Intermittent Spin

0 20 125 0 20 130 0 20 150 0 20 150

0 20 150 0 20 160 0 20 190 0 20 190

0 54 120 0 54 120 0 54 120 0 54 120

0 25 80 0 25 80 0 25 80 0 25 80

0 49 0 49 0 49 0 49

2 55 740 2 55 740 2 55 740 2 55 740

0 20 125 0 20 130 0 20 150 0 20 150

0 20 150 0 20 160 0 20 190 0 20 190

0 54 120 0 54 120 0 54 120 0 54 120

0 25 80 0 25 80 0 25 80 0 25 80

0 49 0 49 0 49 0 49

12 59 740

35 170

35 100

35 15 35

Keep and Churning

Intermittent Spin

Water Supply

Wash and Stir

SelectiveComponents

Rinse TankRotation

SelectiveComponents

Rinse TankRotation

Keep and Churning

Intermittent Spin

End Buzzer

SelectiveComponents

■☆

■■

★★

□□

□□■

□□

■■

■■ ■

■■

□□

□□■

■■

■☆

- 13 -

NA-FS80X1 / FS90X1

■・・It

□・・W

・・T

☆・・S

, a ta

, it s

in.】

Tank Rotation

Water Supply

Tank Rotation

Bubble Sequence

Water Supply

Intermittent Spin

Keep and Churning

Intermittent Spin

Water Supply

Wash and Stir

SelectiveComponents

Rinse TankRotation

SelectiveComponents

Rinse TankRotation

Keep and Churning

Intermittent Spin

End Buzzer

SelectiveComponentsWater Supply

Churning

0 25 80 0 25 80 0 25 80 0 25 80

0 34 120 0 34 120 0 34 120 0 34 120

0 49 0 49 0 49 0 49

12 59 740

■■ ■

■■

l of W

0 15 -43

35 0 15 -43

0 30 120 0 30 120 0 30 120 0 30 120

0 5 50 0 5 50 0 5 50 0 5 50

0 30 120 0 30 120 0 30 120 0 30 120

0 15 50 0 15 50 0 15 50 0 15 50

0 40 -33

200 0 50 -33

200 0 55 -33

0 15 -33

80 0 15 -33

0 40 80 0 40 80 0 40 80

0 15 85 80 0 15 85 80 0 15 85 80 0 15 15 80

0 15 170

11 35 195

11 35 175

11 35 100

11 35 15

0 25 80 0 25 80 0 25 80 0 25 80

1 58 1 58 1 58 1 58

2 55 740 2 55 740 2 55 740 2 55 740

35 170

35 100

35 15 35

35 35 35 35

0 25 0 25 0 25 0 25

0 20 125 0 20 130 0 20 150 0 20 150

0 20 150 0 20 160 0 20 190 0 20 190

0 54 120 0 54 120 0 54 120 0 54 120

0 25 80 0 25 80 0 25 80 0 25 80

0 49 0 49 0 49 0 49

2 55 740 2 55 740 2 55 740 2 55 740

0 20 125 0 20 130 0 20 150 0 20 150

0 20 150 0 20 160 0 20 190 0 20 190

0 20 120 0 20 120 0 20 120 0 20 120

35 170

35 100

35 15 35

■☆

■■

★★

□□

□□■

□□

■■

■ ■

□□

□□■

■■

- 14 -

NA-FS80X1 / FS90X1

■・・It

・・W

・・T

er ☆

・・S

pin【

in.】

Water Supply

Tank Rotation

l of W

Water Supply

Tank Rotation

*1 170

Water Supply

Tank Rotation

Brake *1

Water Supply

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

(Repeat)

Intermittent Spin

Water Supply

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Brake *1*1

*2 35 35

0 40 120 0 40 140

0 17 50 0 17 50

0 40 120 0 40 140

0 33 50 0 33 50

1 30 35 1 30 35

0 10 50 0 10 50

0 40 80 0 40 80

0 31 110 0 31 110

0 31 110 - - - -

- - - -

0 31 110 - - - -

- - - -

0 18 110 0 18 125

0 24 50 0 24 50

0 18 110 0 18 125

0 40 50 0 40 50

0 18 110 0 18 125

0 24 50 0 24 50

0 18 110 0 18 125

0 40 50 0 40 50

2 25 2 25

2 20 740 2 20 740

0 25 0 25

■ □

■★

★★

■ □

■■

■ ■

■■

Intermittent Spin

2 25 2 25

2 20 740 2 20 740

■■

Tank Rotation

Inertia

Tank Rotation

Inertia

Intermittent Spin

End Buzzer

0 40 120 0 40 140

0 17 50 0 17 50

0 40 120 0 40 140

0 33 50 0 33 50

1 30 35 1 30 35

0 10 50 0 10 50

0 40 80 0 40 80

7 20 740 7 20 740

2 25 2 25

■■

■☆

Water Supply

*2 35 35

■☆

- 15 -

NA-FS80X1 / FS90X1

■・・It

・・T

pin【

l of W

0 25 0 25 0 25 ■■ ■

■■

■★

★★

■■

Water Supply

Tank Rotation

Water Supply

Tank Rotation

*1 170 - - - - - - - -

Water Supply

Tank Rotation

Brake *1

Water Supply

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

(Repeat)

Tank Rotation

Brake *1*1

Brake *1

Water SupplyTank Rotation *2

Brake *1

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Water Supply *3

0 30 100 0 30 115 0 30 130

0 17 50 0 17 50 0 17 50

0 30 100 0 30 115 0 30 130

0 33 50 0 33 50 0 33 50

0 30 100 0 30 115 0 30 130

0 30 80 0 30 80 0 30 80235

0 17 50 0 17 50 0 17 50

0 30 100 0 30 115 0 30 130

0 10 50 0 10 50 0 10 50

■■

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Drain *4

Intermittent Spin

Brake *1

End Buzzer *5

0 30 80 0 30 80 0 30 80

0 17 50 0 17 50 0 17 50

0 30 80 0 30 80 0 30 80

0 33 50 0 33 50 0 33 50

0 17 50 0 17 50 0 17 50

0 30 80 0 30 80 0 30 80

0 43 0 43 0 43

1 30 500 1 30 500 1 30 500

0 10 50 0 10 50 0 10 50

Intermittent Spin

35 35 35

0 31 90 0 31 90 0 31 90

0 31 90 - - - - - - - -

- - - - - - - -

0 31 90 - - - - - - - -

0 18 95 0 18 110 0 18 125

0 40 50 0 40 50 0 40 50

0 24 50 0 24 50 0 24 50

0 18 95 0 18 110 0 18 125

0 43 0 43 0 43

1 33 500 1 33 500 1 33 500

35 170

35 100

■■

■ ■■

Brake *1

Water Supply *3

Intermittent Spin

0 43 0 43 0 43

1 33 500 1 33 500 1 33 500

35 170

35 100

0 18 95 0 18 110 0 18 125

0 24 50 0 24 50 0 24 50

- 16 -

NA-FS80X1 / FS90X1

■・・It

★・・T

l of W

0 25 0 25 0 25 ■■ ■

■■

Water Supply

Tank Rotation

Water Supply

Tank Rotation

- - - - - - - -

Water Supply

Tank Rotation

Brake *1

Water Supply

Tank Rotation

Brake *1*3

35 35 35

0 31 90 0 31 90 0 31 90

0 31 90 - - - - - - - -

- - - - - - - -

0 31 90 - - - - - - - -

★★

■■

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

(Repeat)

Brake *1

0 18 95 0 18 110 0 18 125

0 40 50 0 40 50 0 40 50

0 24 50 0 24 50 0 24 50

0 18 95 0 18 110 0 18 125

0 24 50 0 24 50 0 24 50

■■

Brake *1

Intermittent Spin

0 43 0 43 0 43

1 33 500 1 33 500 1 33 500

35 35 35

100Brake *1

Water Supply *3

■ ■

■■

Inertia

Tank Rotation

Inertia

Tank Rotation

Inertia

Tank Rotation

Intermittent Spin

Brake *1

End Buzzer *5

0 30 100 0 30 115 0 30 130

0 17 50 0 17 50 0 17 50

0 30 100 0 30 115 0 30 130

0 33 50 0 33 50 0 33 50

0 40 35 0 40 35 0 40 35

0 10 50 0 10 50 0 10 50

0 30 80 0 30 80 0 30 80

0 10 50 0 10 50 0 10 50

0 43 0 43 0 43

1 30 500 1 30 500 1 30 500

- 17 -

NA-FS80X1 / FS90X1

■・・It

■■

■■ ■

■■

Wash and Stir

Intermittent Spin

Water Supplyand Drain

A Mold CollectionTank Rotating

Water Supply

Mold Crush Churning

Water Supply

Churning

Rinse Tank Rotation

Water Supplyand Rinse

Rinse Tank Rotation

Water Supply

l of W

5 0 235

1 0 130

3 0 120

1 30 780

Brake *1

Brake *1*2

Water Supply *3

1 0 35

1 12 15 160

3 0 120

2 0 120

1 30 130

4 50 35

4 50 130

se【W

l of W

5 0 235

1 0 130

3 0 120

1 30 780

1 0 35

1 12 15 160

3 0 120

2 0 120

1 30 130

4 50 35

4 50 130

Wash and Stir

Intermittent Spin

A Mold CollectionTank Rotating

Water Supply

Mold Crush Churning

Water Supply

Churning

Rinse Tank Rotation

Water Supply

■・・re

・・R

Water Supply

se【W

1 30 780

1 0 35

1 12 15 160

3 0 120

Intermittent Spin

*1Brake

Water Supply

A mold CollectionTank Rotating

Water Supply

Mold Crush Churning

2 0 12023

1 30 130

4 50 35

4 50 130

Water Supply

Rinse Tank Rotation

1 30 780

1 0 35

1 12 15 160

3 0 120

Intermittent Spin

*1Brake

Water Supply

Mold Crush Churning

2 0 12023

1 30 130

4 50 35

4 50 130

Water Supply

Rinse Tank Rotation

■■

■■ ■

■■

- 18 -

NA-FS80X1 / FS90X1

■・・It

235 mm

l of W

n【3m

in.】

g【90

*4Drain

*1Brake

*3Water Supply

*1Brake

Water Supply

*1Brake

3 30 740

*1Brake

Flapping

*5End Buzzer

29 0 780

Intermittent Spin

Rinse Tank Rotation

Mold Crush Churning

Water Supply

Intermittent Spin 0 49

1 30 780

1 0 35

1 12 15 160

3 0 120

2 0 120

1 30 130

4 50 35

4 50 130

235 mm

l of W

n【3m

in.】

*4Drain

*1Brake

*3Water Supply

*1Brake

Water Supply

*1Brake

*5End Buzzer

3 30 740

Intermittent Spin

Rinse Tank Rotation

Mold Crush Churning

Water Supply

Intermittent Spin 0 49

1 30 780

1 0 35

1 12 15 160

3 0 120

2 0 120

1 30 130

4 50 35

4 50 130

■■

- 19 -

NA-FS80X1 / FS90X1

- 20 -

6. INSTALLATION

NA-FS80X1 / FS90X1

An Instruction Manual Extract

When replacing from the right side to the left side.

Fixing Method

You can replace position of the interior drainage hose at the rear and the left side dependingon a drainage place. Please do not take off the interior drainage hose of the cock side.

2 In the case of replacing an interior drainage hose.

Take off a screw fixing connecting part of (a).

(a) (a)

(b)Internal drainage hose

Cock side※ Do not remove !

Take off back panel.

Fix the connecting part (b) with a screw.

※ Hang top of the connecting part on the main body surely.

※ You can replace at the rear side according to the procedure mentioned above. (There is no hose hole cap at the rear side)

Fix the unit with a screw and attach a cap on (a) part.

7 Fix back panel with a screw and attach acap on (a) part.

Lift a unit and take it off toward you.

Take off the cap of (b) part and replace an interior drainage hose from (a) to (b) part.

■ A right below drainage unit sold separately is necessary, if drainage pipe is under a washing machine,

■ The pulling around of the outside drainagehose.

● Don't put the tip into water !

● Raising hose is less than 10cm !

● Extention is less than 3m !

● If the hose is inserted directly into a drainage pipe, please confirm to fix firmly.

● If there is a lot of waste thread at drainage pipe and difficult to remove, please buy a waste thread box sold separately.

Right below drainage unit(sold separately) N-MH1 (back cover)

Please don't put a hose ina drainage pipe directly.

Because the tank is suspended structure, a drainage hose may come off or be torn by vibration at the time of the spin.

Less than 10cm

Less than 3m

- 21 -

NA-FS80X1 / FS90X1

6 Confirm Level

7 Perform test operation to check water leak, abnormal sound and error alart.

Check a Level Meter Adjust Inclination

(Front)

(view from the bottom)

Bubble horizon ● No need for adjustment

● Raise

● Install rubber sheet.

● Install rubber sheet. ■ In case of protrude greatly

■ Adjusting inclination

■ Open a faucet and operate after closing a cover (don't put anything in the tank!).

■ Adjust it with an adjustment leg (one place of right front part)

■ Install an attached adjustment rubber sheet to adjust for the other case.

1 Loosen an adjustment leg knob. 2 Turn an adjustment leg to adjust inclination. 3 Tighten an adjustment leg knob to fix it.

Wood plate, etc.● Raise

● In case for gathering of bubble is slant : please adjust to similar position as above with an adjustment leg. Then adjustment leg. Then adjust in details.

● Adjustment rubber sheet ● Stacking up (10mm)

● Indicates abnormal for following cases.

Level Meter

Put a board under theleg of the other side todecrease protrude.Then adjust in details.

Back is high

Right is high

Front is high

Left is high

Loosen

※ Adjustment rubber sheet cannot be installed to an adjustment leg.

Tighten

Adjustment leg knob

Higher Lower

Adjustment leg

Holding Course + Good Quality House laundrybutton and push Power on button.Push Course button during is displayed. Remaining time (4min) is displayed and startsoperation. (Operation stops automatically after 4min)

・The rise of the drainage hose is higher than 10cm・The drainage hose is not connected correctly.・The drainage hose is clogged.

・Water supply hose is connected but a faucet is not opened.

Install a bigger one upper side.

- 22 -

7. TABLE OF ERRORS

7.1 Service Check

The number of pushingthe water level button

CheckSequence

CheckContents

• Timer display• End information• Power supply auto-off

Display during operation : wash 3 min • rinse 1 time •spin 40 sec and remaining time blinking. • End buzzer sounds 3 times and [88] is blinking at the same time. Turn off the power automatically after operation. If other than [88] is indicated, please check B.

1 B • Confirm washing operation• Confirm water supply valve operation• Confirm bath pump operation

Display during operation : wash 3 min blinks andremaining time display counts down.

2 C • Confirm spin operation• Confirm the cover switch operation

• Perform washing sequence for 6 min even though there is no water in a tank.• By pushing [wash] button, 3 mode can be selected.• To push [wash] button 1 time for passable confirma- tion of the water supply valve.• Push [wash] button 2 times to make a bath pump passable.• Push [wash] button 3 times to return for washing sequence.• In case of abnormal function in the controller, [H05] will be indicated.

Display during operation : spin 40 sec blinks, remaining time display counts down and [cover lock]lamp turns on.

• Lock cover and operates spin sequence for 8 min.• [22L] • [60L] of the water level turns on when contact points of each cover switch turn off. Lead switch ------------------ [ 22L] Cover (SF) switch ---------- [60L] For NA-FS70H1, it is 60L 59L

3 E • Setting to raise 2 ranks of judgement water level of the quantity of cloth detection

Display during operation : rinse 1 time • spin 40 secblinking, [L0] or [L1] blinking.• To push [Washing] button, [L0] turns into [L1]. To push [Star/Hold] button for setting. Water level is judged 2 rank higher in [L1].

Indication Operation

1. Turn off power supply.2. Hold [washing] and [water level] botton at the same time by one hand.3. Turn on power supply.4. Release the buttons as referred to above 2, 3 (Check A)5. Push [water level] button within 3 seconds and select a test sequence match it with a check sequence desired. (Check B, C, E, G, H, P)

NA-FS80X1 / FS90X1

Watervolume

3 STARTHOLD

onward

- 23 -

NA-FS80X1 / FS90X1

The number of pushingthe water level button

CheckSequence

CheckContents

Display a historyof the abnormalinformation for thepast 3 times

Display [E] initialy, whenever [wash] button is pushed,it turns the last time (22L turns on) the time before last (22-35L turns on) the time before 2 last times (22-47L turns on) [E]• Displays [U] or [H] and numbers in turn if abnormal information reported before. If no abnormal record [00] is indicated.• To push [rinse] button during abnormal record (the last time - time before 2 last times) indication, shows abnormal repetition number of times. If no abnormal record [00] is indicated. While pushing [spin] button, it displays course, work sequence (wash, rinse, spin), quantity of water, bath water setting and remaining time, when abnormality occured. While pushing [bath water] button, it displays the work sequence that abnormality occurred by 2 digits. 0 : Quantity of cloth sensing 1 : Waiting for detergent injection 2 : Water supply 3 : Churning 5 : Unite cloth and churn it 6 : Drain 7 : Intermittent spin 8 : Bubble cut intermittent spin 9 : Waterfall rinse A : Spin B : Bubble cut spin C : Inertia While pushing [reservation] button, it displays the rinse number of times and the spin number of times by digits, when abnormality occurred.

The number ofrinse spinning

The number ofrinse churning

[ 1 1 ]

• It shows [C] firstly and then it displays the operating number of times by pushing [wash] button.1 time pushing, it displays the washing operating number of times at the digit column of [1,000 • 100].2 times pushing, it displays the washing operating number of times at the digit column of [10 • 1].3 times pushing, it displays the drying operating number of times at the digit column of [1,000 • 1].4 times pushing, it displays the drying operating number of times at the digit column of [10 • 1]. (When displaying digit column of [10 • 1], [reservation] is turned on) (When displaying drying operating number of times, [detergent] is turned on)

Indication Operation

5 H Displayingnumber of operating forwashing/drying

Display during operation : wash 3 min • rinse 1 timeshow blinking.

- 24 -

7.2 Standard Self-Diagnosis Function (Abnormal Information)

Display Part An abnormalContents

Detected Contents

When a water level sensor doesn’tdetect reset water level, even if itpasses from a drainage start for 12 minutes. But it opens and closes a drainage valve every 4minutes.

Open and close thecover.

Drainage is abnormal.

• Confirm and adjust blocking of the drainage course such as a cock valve, a drainage hose and a drainage pipe of the house. • Confirm and adjust the rise of the drainage hose and the extension dimensions.• Confirm and exchange of the sensor circumference including the water level sensor, air tube.

• Please close a cover.

A check procedure / Measures

A cancellationMethod

※ It displays automatically when it detected an operation mistake or an abnormality during operating.Then stop the operation.

The indication of the abnormality detection displays alphabet (U or H) and a number in turn.( For U11 )

※ Buzzer alert is performed for all of U displaying and only H21.

NA-FS80X1 / FS90X1

“ U ” “ 11 ”

In case of cover open, even if washing passes from a start for 2minutes.

Close the cover.Cover open isabnormal.

※ ※ When a cover open.

• The exchange of the controller (a lead switch) for displaying.

※ When a cover close.In case of cover open, whenspinning starts.

• Please correct it.When an ambalance is detectedduring centrifugal force washingand spinning.

Open and close the cover.

Ambalance isabnormal.

※ ※ Are cloths clustered?

• Please adjust level.

※ Is the machine inclined or wobbled?

• Check water supply and the faucet open. And adjust it.• Check and exchange of the water supply valve and load side controller.

After water supply start, water level doesn’t reach to the settingwater level even if it passes for30 minutes.

Open and close the cover.

Water supply isabnormal.

※ ※

After water supplement in washsequence, water level doesn’treach to the setting level even ifit passes for 20 minutes.

Without water supply.

• Check water leak from the cock part and adjusting it.• Check water leak from other parts and adjusting it.

• Check proper plug connection.• Replacement of the water level sensor.• Replace of the load side controller.• Noise • Electric wave obstacle.

※ With water supply.

- Hold [course] buttonmore than 5 sec.

Child lockoperation.

※ In the case of the child lock [on], after power supply button is [on],it shows [CL] on the remainingtime display for 2 seconds.

When the input frequency of thewater level sensor is out of an appointed range.

Push [power off] button.

Water level(pressure) sensoris abnormal.

• Replace a controller of the load side.

When it detected a short circuit ofthe power supply relay in the loadcontroller.

Pull a power plug out.Power switchrelay short isabnormal.

• Replace a controller of the load side.

When wiring data into memorywas not possible. Only in servicecheck B.

Push [power off]button.

Access to microcomputermemory is abnormal.

• Check connector contact of the rotary sensor and breaking lead wire.• Replacement of the machine motor.• Replace a controller of the load side.

When there isn’t input signal froma rotary sensor at the time of a motor ON sequence.

Rotary sensoris abnormal.

- 25 -

NA-FS80X1 / FS90X1

Display Part An abnormalContents

Detected Contents

When communication control isabnormal between a controller forload and a controller for indication.

Pull a power plug out.Communicationline disconnectionis abnormal.

• Breaking communication line or connector contact error.• Replace a controller of the load side or display side.

• Replacement of the water supply valve.• Check output and replacement of the load side controller.

A check procedure / Measures

A cancellationMethod

When a water level sensor detectsoverflow water level more thanconstant time.

Overflow wateris abnormal.

Operate geared motor for drainageand drain water.

• Check disconnected connector of geared motor and adjustment.• Passable check and replacement of the geared motor.• Check input and output of the load side and replacement controller. For details refer to a clause of [trouble diagnosis of H25, H26].

When geared motor doesn’t worknormally even if it passes from thestart of the drainage work sequence for 3 minutes.

Geared motor for drainage isabnormal.

When an opening and shutting ofgeared motor (drainage valve) isn’t normal, it does not change even if it is controlled to becomenormal.

• Check disconnetion of geared motor connector and adjustment.• Passable check and replacement of the geared motor.• Check input and output of the load side and replacement controller. For details refer to a clause of [trouble diagnosis of H25, H26]

• Check disconnetion of a connector• Passable check and replacement of the door lock switch• Check output from a load side controller and replacement.

When geared motor doesn’t worknormally at the time of pulsatorchurning.

Clutch is abnormal.

In the case it does not drive evenif there is output to a cover lockswitch.

• Check if too much cloths in a washing tank.• Check cloths or waste thread filter are caught in an inner cover.• Check connector disconnection of a motor and the rotary sensor.• Replacement of the machine motor.• Check output from a load side controller and replacement.

Push [power off]button

A door lock switch is abnormal.

When the signal of the rotarysensor doesn’t input at the time ofa washing rotate for 2 minutes.

Push [power off] button.

Overloading. ※

• Check the power supply voltage.Input voltage exceeds 120V. Auto-off.High voltage. ※

• Check the power supply voltage.Input voltage is lower than 65V. Push [power off]button.

Low voltage. ※

• Replace a controller of the load side.• Check short circuit of a coil and replacement of a bath pump or the machine motor.

When overcurrents more than 8Aflow in circuit of inverter 1.

Inverter circuitovercurrent.

• Check operation of the machine motor.• Replace a controller of the load side.

When a demagnetization electriccurrent detection circuit worksmore than the predetermined number of times.

Abnormaldemagnetizationelectric current in machine motor.

- 26 -

7.3 Troubleshooting of H25, H26If abnormal indication [H25] and [H26] appeared, perform following trouble diagnosis and specify a trouble part.

NA-FS80X1 / FS90X1

● Output measurement point of each geared motor

Drive geared motor and AC100V is output from a controller toa geared motor drive circuit.

YesYes

Yes● When geared motor continues rotating several laps.

● In case of geared motor does not drive

A check point and judgment Measures

● Replace the controller

● Replace a lead wire U

● Replace the geared motor

・In the case of H25, drive by [spin only] and measure between ④ - ⑥.

・In case of H26, service check B and measure between ⑤ - ⑥

(measure during drive)

Check AC100V is output from the position sensing circuit.・In case of H25, measure between ③－⑥

・In case of H26, measure between ②－⑥

Check voltage alteration in the position sensing circuit during a rotation.・In case of H25, measure between ③－⑥

・In case of H26, measure between ②－⑥

Repeat AC100V and 0V periodically

① Brown white lead wire② Orange lead wire③ White red lead wire④ White blue lead wire⑤ Brown lead wire

Yellow 1 pin connector

⑥ Yellow lead wire 62

Red 3 pin connector

Blue 2 pin connector

- 27 -

8. DISASSEMBLY • ASSEMBLY INSTRUCTION

NA-FS80X1 / FS90X1

8.1 Controller Display

It may cause a fire, emitting smoke and electric shock.

Fireproofcover

Pressureconnectingterminal

Pull a power

plug out

● To connect the lead wire, use a solderless terminal and tighten it firmly. (Use a specified part, regular bonding pliers)● Install a flame protect cover (incombustibility-proof) to completely cover the connection part and seal an opening part with tape. (Re-use the incombustible cover attached with the product)● Fix lead wires firmly by wire fixing part to prevent contact with revolving part, high temperature part and metal end faces. ● Confirming proper wiring diagram for reparing. ● In case of lead wire disconnection, replace whole lead wire unit. Do not cut a part of lead wire unit and use it.

● Please make sureto pull out a powerplug beforedisassembly. It maycause an electricshock or injury.

● Do not remodelappliances,instruments andparts. It may cause break down or fire.

● Straightly pull outor insert a fastonterminal. Do not twist it. It may causedamage or fire.

Warning Warning

Illustration Disassembly Procedure

Water proof cover

Panel sheet A

Controller display

● Necessary tool plus driver

● Replacement of controller display

(1) Take off top cover installation screw (2 pieces) at the back side (2) Take off the window cover packing (for each right and left) at front, right and left of top cover. Then take off installation screw (for each right and left) of the top cover.

● Make sure to put a groundwire on human body during replacing part ortrouble diagnosis.

・ It may cause a trouble by static electricity. ・Touch power plug and the ground wire to clear voltage difference.

(3) Lift back side of the top cover and slide it toward you and take it off. (front fix by front hook)(4) Lean the top cover with a product and a wall. (5) Take off a water proof cover installation screw (2 pieces) and disconnect a connector.

(6) Take off a controller installation screw (5 pieces) and remove the controller.

Caution

- 28 -

8.2 Door Lock Switch

NA-FS80X1 / FS90X1

Illustration Disassembly Procedure

Panel sheet A

Door lock switch

Controller display

8.3 Load ControllerIllustration

Controller case cover

Back panel

Controller (loading)

Disassembly Procedure

● Replacement for load controller

(1) Take off back panel installation screw (6 pieces)

(2) Take off controller case cover (7 places of hook)

(3) Take off controller connector and ground wire installation screw (2 pieces). Then lift and slide controller unit (fixing with hook at right and left side) to remove.※ Light blue 6 pin connector is no use

● Replacement of door lock switch

(1) Refer to procedure (1) to (4) [replacement for controller display].(5) Take off panel A sheet (2 screws)

(6) Take off door lock, switch installation screw (2 pieces). (7) Take off the connector of the door lock, switch and replace it.

- 29 -

NA-FS80X1 / FS90X1

8.4 Water Supply Valve • Baht Pump • Water Level Sensor • Lid Switch Illustration Disassembly Procedure

● Necessary tool plus driver ・minus driver

● Replacement of water supply valve

(1) Open the cover and take off cover hinge axis (each right and left side)※ Push down the cover hinge axis by minus drivers and take it off.

(2) Take off 2 installation screws of back panel base (each right and left side) (3) Take off cap A, B and remove a panel base

(4) Take off water supply valve installation screw (2 pieces) (5) Take off connector (2 spots)(6) Cut off hose unity band and take off the hose ※ After hose installation, please fix a unity band

● Replacement of bath pump

※ Use adhesive for the bus pump replacement(1) Refer to procedure (1) to (3) [replacement of the water supply valve] (4) Take off hooks at right and left (2 spots) of bath pump (5) Remove a hose (6) Take off a connector※ When you install an unti-reverse valve hose and a subhose, apply adhesive on the market. Check water leak.

● Replacement of cover switch

(1) Refer to procedure (1) to (3) [replacement of the water supply valve] (4) Take off installation screw (2 pieces) of the cover switch(5) Disconnect connector of the cover switch ※ Perform service check C for trouble diagnosis of the cover switch

Cap ACap B

Bath pump

Water level sensor Cover switch

Watersupply valve

Panel base

- 30 -

NA-FS80X1 / FS90X1

● Put any protector such as gloves when repairing lower part of the product

・ It may cause injuries

Caution

8.5 Bearings (Mechanical Motor)Illustration Disassembly Procedure

● Necessary tool

･ Plus driver ･ Hammerless flange nut turning tool (HW-25K) ･ Bearing installation nut turning tool (HW-18) ･ Ratchet box wrench (HW-35)

● Replacement of bearings (mechanical motor)

(1) Take off top cover installation screw (2 pieces) at the back side.

(2) Take off the window cover packing (for each right and left) at front, right and left of top cover. Then take off installation screw (for each right and left) of the top cover. (3) Lift back side of the top cover and slide it toward you and take it off.(4) Lean the top cover with a product and a wall.

(5) Take off a spin tank cover. (8 Screws)(6) Take off a pulsator.※ Don't completely remove the screw. Lift up the palsator with screws.

(7) Take off shaft bush, spin shaft nut and D shaft washer B. (8) Pull out a spin tank.

(9) Tilt the product to the side without drainage hose.※ Put a cloth under the body to prevent from scratch.(10) Take off screws of a water tank support installation plate B (2 screws).(11) Disconnect a connector of motor and a rotary sensor.

(12) Take off installation screws (6 screws) of the bearing (mechanical motor)

Water proof cover

Panel sheet A

Spin tank cover

ShaftBushing

Spin shaft nut

D shaft washer B

Bearings(mechanical motor)

Water tank supportinstallation plate B

Shaft bush

Spin shaft nut

D shaft washer B

- 31 -

9. EXTERNAL DIMENSION FIGURE

NA-FS80X1 / FS90X1

599 (hanger part and hose external shape)

Drainage hose(available to draw right and left)

Cover (opened)

Cover spaceangle 110

41.5 (from body side)

92 461

135 155

Adjustment part (1 part)

558 (hanger part width)

554 (body width)

- 32 -

10. CIRCUIT DIAGRAM

10.1 Electric Circuit Diagram

NA-FS80X1 / FS90X1

Please use specified part for replacment to maintain safety and performance.Part with mark is a safety part.

Warning

- 33 -

NA-FS80X1 / FS90X1

10.2 Controller input • Output Measurement

● Beware of electric shock at a lead wire of charge unit during measurement.

※ ( ) is a color of the connectors※ Disconnect connectors for measuring resistance

Bewareof Electric

・Re-confirm the following output level and resistance at the time of controller replacement.・Measure output level by tester while switching a load part ・Value mentioned below may be changed depend on power supply voltage or an error of the tester. ・For the motor measurement, apply 3 combinations of [red - blue] [red - purple] [blue - purple] to confirm normal value. ・Value of the push switch measurement is 220~240V without pushing power button and 0V to push the button once.

Warning

Red-White

YellowRed-White Blue-

Gray-Black

C101 ZNR108Z

W2449-7JP

Blue RedPurple

Yellow -Red

Yellow -White

FUSE102

D201FUSE121

C123T121

J156J155 J154

J109J106

8 1J55

J67 J8

C434Light-Blue

J121J122

J112J114J115

J66J117

PTR203

PTR204

J52R124

y) (Blu

2.5+ -0

☆163+-0.1

WhiteCN108

J151 12

R129 R126

J110 C128

J108J161

J171J71

J179J15

R221J10

J169J163

J74 J72P

k R239

J175J176

J172J173J174

Q204 2 34

R214J160

1Purple

R204Brown

Orange

J164J166

ZNR109

GrayCN201

Orange

e Brown

Yellow

BlueCN205

Brown-White

WhiteCN203

RedCN202

White-Red

BlueCN701

RedJ73

- 34 -

11. PARTS EXPLODED VIEW AND REPLACEMENT PARTS LIST

11.1 Parts Exploded View : Part A

NA-FS80X1 / FS90X1

A27A21

A14A15

A19A21

Watervolume

Bathwater

Reserve

Reserve(hours)

VentilationDrying

ProgramChild Lock (Press 5 seconds)

Good-qualityhousecleaning STARTHOLD

- 35 -

NA-FS80X1 / FS90X1

Important safety notice :

11.2 Replacement Parts List : Part A of NA-FS80X1 / NA-FS90X1Parts List

Components identified by mark have special characteristics important for safety.When replacing any of these components, use only manufacturer's specified part.

COLOUR : SILVER

COLOUR : BLUE

AXW06577JP50

AXW06577JP00

AXW99087JP50

AXW99087JP00

AXW01307JP00

AXW131W7LN00

AXW131W7GF00

AXW21507JP00

AXW12757GH00

AXW12607GJ00

AXW12607JP50

AXW026739600

AXW292122206

AXW1116-7GF0

AXW11657GF00

AXW001G7JP00

AXW001G7JR00

AXW164-6RU0

AXW119615200

AXW09687GF00

AXW166123510

AXW024T02800

AXW24987GF00

AXW001B7JP00

AXW001B7JR00

AXW01467JP00

AXW01467JR00

AXW353-6YF0

AXW01637JP00

AXW001J7GF00

AXW01477GF00

AXW024S7GF00

AXW12387GF00

AXW021D7JP00

AXW161901206

AXW01437GF00

AXW14A7JP00

SWITCH INSTRUCTION

SWITCH SETTING CHART

PANEL A

PANEL A BOARD UNIT

SOAP CASE A

FEED VALVE SPACER A

FEED HOSE B

FEEDING PORT PACKING

FEEDING VALVE

LID HINGE SPRING

LID HINGE SHAFT

LID UNIT

LID PACKING A

MAGNET

MAGNET BRACKET

SAFETY SWITCH UNIT

PRESSURE SENSOR UNIT

HOLDER B

BODY B UNIT

PANEL FACE B

LEVELLER

WRINGER PORT FRAME PACKING

PANEL FACE UNIT

PANEL FACE C

PRINT BASE A UNIT

WATER PROOFING COVER

SOAP CASE B UNIT

DOOR LOCK SWITCH

PANEL A SHEET

CONNECTOR LEAD WIRE UNIT

Ref.No. krameRytefaS.oN traPemaN traP

FS80X1 FS90X1 MAL DBD RBD TH VN INDO PH

Model Country / Qty

Screws

MAGNET BRACKET

BODY B~BODY A

PANEL FACE C

XTB4+15CFJ

XTS3+6BV

XTWAXW469J

XTV3+10BFK

BINDING TAPPING SCREW

FLUSH HEAD TAPPING SCREW

SPECIAL TAPPING SCREW

PRESSURE TAPPING SCREW

Model Country / Qty

PANEL FACE C UNIT,PANEL A,

FEEDING VALVE,SAFETY SW.,ETC

- 36 -

11.3 Parts Exploded View : Part B

NA-FS80X1 / FS90X1

B14B16

B18B20

- 37 -

NA-FS80X1 / FS90X1

11.4 Replacement Parts List : Part B of NA-FS80X1 / NA-FS90X1Parts List

COLOUR : WHITE

COLOUR : DARK GREY

TYPE : C3

TYPE : C2

TYPE : S3

EXTERNAL EARTH

ENGLISH LANGUAGE

THAI LANGUAGE

t = 1mm.,LEFT

t = 1mm.BACK

AXW001A7JP00

AXW001A7JP50

AXW01107JP00

AXW03017JP00

AXW03396UP00

AXW03357EC00

AXW03436JZ00

AXW01537JP50

AXW01537JP00

AXW01537JPF0

AXW01537JR50

AXW01287JP00

AXW01567GH00

AXW04707JP00

AXW004A729A4

AXW004A730A4

AXW004A772A4

AXW003C6SP20

AXW99047BK60

AXW99047BK10

AXW24277JP00

AXW99056UP00

AXW024C7JP06

AXW024C7JR06

AXW014B7JP00

AXW002E6XB10

AXW02456XB00

AXW012D7BR00

AXW90466NTB0

AXW90467JP50

AXW243003800

0466AA6M

BODY A UNIT

BASE A

LEG COVERING

ADJUSTABLE LEG

ADJUSTABLE LEG THUMB

NAME PLATE

HOSE HOLE COVER A

BACK PANEL

WIRING DIAGRAM

POWER CORD UNIT

EARTH WIRE UNIT

DRAIN INSTRUCTION

CONTROLLER CASE LID

CORD CAUTION LABEL

CONTROLLER UNIT

LEAD WIRE UNIT

FLEXIBLE HOSE B UNIT

HOSE BAND

SERVICE PRESSURE HOSE UNIT

BODY A PROTECTION

DY A PROTECTION

Ref. Part Name Part No. RemarkSafety

Part Name Part No. RemarkSafety

No. FS80X1 FS90X1 MAL DBD RBD TH VN INDO PH

Model Country / Qty

NOISE FILTERB24 1 1 1 1 1 1 1

AXW9BOB2 1 1 1 1 1 1 1

Screws

BACK PANEL

BODY A~EARTH

EARTH~POWER CORD

BASE A

HOSE A UNIT

EARTH~POWER CORD

XTTAXW444J

XWEAXW589J

XTN4+8HFJ

XSN5+10BNS

XTTAXW444J

XTWAXW471

XWC5AFJ

SPECIAL WASHER

SMALL TAPPING SCREW

SPECIAL WASHER

Ref.No. FS80X1 FS90X1 MAL DBD RBD TH VN INDO PH

Model Country / Qty

t = 30mm.,FRONT,BACK,RIGHT,LEFT

- 38 -

11.5 Parts Exploded View : Part C

NA-FS80X1 / FS90X1

C24 C21

C16 C18

- 39 -

NA-FS80X1 / FS90X1

11.6 Replacement Parts List : Part C of NA-FS80X1 / NA-FS90X1Parts List

INNER LID,OUTER TUB COVER

FOR CLUTCH

FOR DRAIN

AXW02007GF00

AXW11416RX00

AXW32247JP00

AXW02577BK00

AXW05017JP00

AXW05046ZR00

AXW15176RU10

AXW151980200

AXW022A6RU10

AXW11987JP00

AXW002A7JP00

AXW034U7JP00

AXW02648110A

AXW002Q7JP00

AXW12017JP00

AXW348202906

AXW012X7JP00

AXW020A7GF00

AXW348203006

AXW009D7DE00

AXW002D7JP00

AXW0245EC00

AXW02347JP00

AXW32327DA00

AXW12467DA00

AXW22757GF00

AXW02047GF00

INNER LID

LID STOPPER A

OUTER TUB COVER

O RING

PULSATOR UNIT

SHAFT BUSHING

SPINNER SHAFT FLANGE NUT

SPINNER FLANGE WASHER B

FILTER UNIT

DETERGENT SLIT

TUB UNIT

SUSPENSION UNIT

SUB HOSE CLAMP

SUB HOSE UNIT

OUTER TUB A

GEARED MOTOR

OUTER TUB B UNIT

MECHANISM CASE UNIT

GEARED MOTOR

VALVE UNIT

FLEXIBLE HOSE A UNIT

HOSE BAND

OVER FLOW HOSE B

SPINNER PLATE B

OUTER TUB GASKET A

FEEDING HOSE TIP B

FEEDING HOSE TIP

Model Country / Qty

AXW035A7JP00BALANCER UNITC28 1 1 1 1 1 1 1

Screws

OUTER TUB COVER

PULSATOR UNIT

EARTH U~OUTER TUB B

GEARED MOTOR (FOR CLUTCH)

GEARED MOTOR (FOR DRAIN),

SPINNER PLATE B

MECHA-CASE U~OUTER TUB B

XTWAXW435

XSSAXW682

XTN5+10HFJ

XYFAXW506EJ

XTWAXW6517J

XVGAXW827J

SPECIAL SMALL SCREW

PAN HEAD TAPPING SCREW

SPECIAL BOLT

Model Country / Qty

- 40 -

11.7 Parts Exploded View : Packing Part

NA-FS80X1 / FS90X1

D12 D10D13

D9 D15

1) Setting of a basket supporter and manual 3) The packing of the main body

4) Finish up

2) Turn up a case sheet and set

(1) Set a position of tank U as per the right figure

(3) Set basket supporter A, B and a manual

Lint filter

Put the lint filter at the position of

either A, B, C, D

(2) Open an inner cover and set a case sheet

①Roll up both front ends of a case sheet into the backof the inner cover

Protrude part

Figure 1

① To set the basket supporter B, fit completely to the internal circumference protrude part of the balancer case. (figure 1)② Set a manual in the slant part of basket supporter B. ③ Close an inner cover. ④ Set the basket supporter A fitting with indented front part of basket supporter B. A case sheet must be located in between body B and basket supporter A to be protected.

① Follow a procedure as left figure. Roll up and tuck the case sheet into an inner cover. ② Close a cover.

Insert it betweenproduct and case A

Front side

11.8 Replacement Parts List : Packing Part of NA-FS80X1 / NA-FS90X1Parts List

FRONT SIDE

BACK SIDE

FRONT : 2PCS./SIDE

ENGLISH + THAI

ENGLISH + MALAY

ENGLISH + VIETNAM

ENGLISH + INDONESIA

AXW90017JP50

AXW90017JP00

AXW90047JP00

AXW90607JP00

AXW90157JP00

AXW90157JP50

AXW90167JP00

AXW21586ZR00

AXW090B7JP00

AXW99017JP00

AXW99017JP50

AXW99017JPA0

AXW99017JPF0

AXW90576UP20

AXW90207JP00

AXW90547JP00

AXW90557JP00

AXW90107JP00

XTTAXW444J

PROTECTION CASE A

SIDE CUSHION

POLYETHYLENE COVER

CORNER CUSHION

CORNER PAD

BOTTOM COVER

PROTECTION CASE B UNIT

OPERATING INSTRUCTION

ACCESSORY BAG

CARTON PLATE

SPIN TUB SUPPORTER A

SPIN TUB SUPPORTER B

SPIN TUB PROTECTION

Model Country / Qty

- 41 -

NA-FS80X1 / FS90X1

DETAIL CHANGE NOTICE

2 ADD PART NAME & PART NO. FOR SALES SUPPLY37

1 ADD BALANCER PICTURE FOR SALES SEPARATE PART38

2 ADD PART NAME AND PART NO. FOR SALES SEPARATE PART39

MAR. 2013

1 ADD PICTURE OF NOISE FILTER PART ASSY SEPARATE36JAN. 2012

REVISION REMARKDETAILPAGEITEM NO.

Order No. PHAT090901C3 Service Manual - Panasonic...Order No. PHAT090901C3 Service Manual(Revision :...

Documents