Our Brouchure

transcript

10300 Southeast Jennifer Street

Clackamas, Oregon 97015

Tel: 503-656-0901

Fax: 503-656-1985

www.marksmetal.com

FORMS FOR THE PRECAST

CONCRETE INDUSTRY

Superior Solutions Through Experience & Innovation

CAPACITY Vaults

Solid tapered and collapsing core

Roll-out sides

Custom block-outs and pallets

Box culvert forms

Septic tank forms

Structural Components

Columns

Architectural wall panels

Bolt down or magnetic rails

Column cover forms

Casting decks

Manhole Equipment – Wet and Dry cast

Risers

Flat top lids

Pipe Forms – Wet and Dry cast

Joint Rings

Fabricated steel

Rubber gasket

Mortar joint

Bell Bands

Catch basins

Precast foundation systems

Light pole forms

Spun or still cast

Railroad grade crossings

Lamp pole bases

Stair forms

Planter and bench forms

Decorative architectural forms

Fence wall, post and caps

Columns

Columbarium forms

Vaults 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Phone: 503-656-0901 Fax: 503-656-1985 www.marksmetal.com info@marksmetal.com

All vaults are custom

designed to meet

your specific casting

and production

requirements

Hinge out side forms with tapered core

Vertical joints at side forms and core

for multiple casting configurations

Communications vault with crank bolts, bolted corner

connections and turning trunnions for stripping

Two compartment 800 gallon septic

tank form with hinge out sides

Single compartment Oil

Interceptor form with

removable backform tub

and hinge out sideforms

Median Barriers 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

20’ Lg. x 42” deep transition barrier sides

12’ Lg. x 32” deep twin barrier form with tapered pin & scupper blockouts

Twin Cavity Barrier Forms to meet D.O.T. Specifications

Standard 20’ K-Rail Barrier Form with

Hinge out scupper & drain blockouts,

Stake pocket blockouts & lift hole blockouts.

End headers to meet highway specifications

Components are Match

marked for a quick and

reliable fit-up

10’ Lg. Twin cavity barrier forms

with turning trunnions at ends for

stripping operation.

B.C. Canada Median Barriers

10300 S.E. Jennifer Street ● Clackamas, Oregon 97015 Phone: 503-656-0901 Fax: 503-656-1985

www.marksmetal.com info@marksmetal.com

CRB-H & CRB-E Standard

Highway Barrier Form

690mm tall x 2500mm long

CDB-E Standard Highway

Drainage Barrier Form

CTB-2H Transition Barrier

Form 810mm to 690mm tall,

2500mm long

CBN-H & CBN-E Bull-nose

Barrier Form 460mm to

End Headers designed to secure

Connection anchors at the

Required locations Forms shown with turning trunnions and spreader

bar with keyhole plates for stripping operation

Catch Basins 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Jacking Stations each

leg for stripping using

standard bottle jack

Catch Basin forms with tapered core.

Pull back and hinge out jacket assembly

Catch Basin form with multiple

section core and jacket assembly

11’ Catch Basin form with

extended base and adjustable

pallet

Curb Inlet form with

multiple section core

and jacket assembly

Grade Rings 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

(20) Cavity Spacer Ring Form with Collapsing Core

Large Battery form with Collapsing core and Machined Rings

This One Form will Cast Three Different Products

Pipe Forms 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Miscellaneous

Repairs and modifications to existing forms

Large Diameter

Pipe Forms

Wet cast and

Dry cast Jackets

and cores

Eccentric Cone Form with hold down frame & latches

Joint Rings 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Machined

and ready

For service

Fabricated Steel Construction - Stress Relieved Prior To Machining

Post heat treating -

ready to machine

Marks Metal Technology’s extensive

experience in heavy plate and bar

rolling, aggressive pursuit of welding

refinement and in -house machining

capability gives us the edge in

producing the finest quality

joint rings available

Specialty Forms 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Wet Cast Meter Box Gang Forms with pallets &

Hinge out sides. Used with vibration table.

Wet Cast Meter Box Gang Forms with pallets &

Hinge out sides. Used with vibration table.

(30) Cavity pipe sleeper or parking bumper form.

Provided with lift eyes & rollover wheels for stripping

Forms for Detention Basin System. Form has

hinge out sides with blockouts & collapsible core

Rail Crossing center tub & inner

slab forms requiring tight tolerance

fabrication

Headwall Forms 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Standard 26-28 Headwall Structure Form

Adjustable in height from 2946mm to 3632mm

With the back and side jackets

removed, the product is easily

stripped using a (4) point pick.

With the lower hooks removed,

the product hangs vertical and

plumb for ease in installation.

Misc. Forms and Equipment

Large diameter (4) piece pedestal jacket sets for wind

farm projects. Embed and Template rings also available

Collapsible hole formers for specified

wall thickness and pipe diameters

500 Gallon Water Trough Form with Float box

(100) Pocket Drywell Barrel

Tight tolerance Bell bands for jacking pipe

Shipping 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Marks Metal Technology is committed to providing Quality in the

manufacturing of Precast Concrete Forms. The 72” Extended Base

and Riser Forms shown, were produced quickly and shipped via a

Hercules C-130 to Kotzebue, Alaska, north of the arctic circle. The

construction season on the Baldwin Peninsula is very short,

which required a very quick response to the need.

Form Restoration

This 6’ x 3’ Drycast

Box Culvert Form has

been completely

restored from the

ground up and is back

in service at a fraction

of the cost of

a new form.

Form Accessories

Contact Our Sales Depart-

ment at

1-800-526-1031

Or Order Di-rectly

Online at

marksmetal.com

Alignment Blocks with 9/16” hole

Core Collapsing Lock Assembly

Anchor Post with hardware

Typical assembly showing the Core Lock and Reversible Step

Pin Blockouts in use

Bent Handle Form Latch Assembly (Anchor post not included)

Straight Handle Form Latch Assembly (Anchor Post not included)

Reversible Step Pin Blockout

Typical assembly showing form latch applications

Prices are subject to change

Superior Solutions Through Experience & Innovation

Company Profile 10300 Southeast Jennifer Street

Tel: 503-656-0901

Fax: 503-656-1985

Email: info@marksmetal.com

www.marksmetal.com

• Cones

• Plates

• Hoppers

• Heavy Bands

• Casings

• Screens

• Liners

• Reducers

• Underground Utilities

Plate and Cone Rolling /Forming

• Hardway Beams

• Easyway Beams

• Split Tees

• Cambering

• Angles

• Rails

• Pipe

• Channel

• Stairways - Circular

Architectural and Structural Rolling

• Shearing

• Forming

• Rolling

• Cambering

• Bumping

• Fitting

• Welding - Robotic

• Tee Splitting

• Fabrication

Metal Processing Services

• Plate Sizing

• Small Parts

• Prototypes

• Signage

• Heat Sensitive Parts

• Holes Ready to Tap

• Interlocking Parts

• Pre-Machining

WaterJet Cutting

• Vaults

• Architectural Forms

• Pipe Forms

• Joint Rings

• Structural Members

• Lamp Poles

Custom Concrete Forms

The Waterjet Advantage:

• Waterjet can cut many types of material,

especially materials that cannot be cut with

laser or thermal cutting methods.

• Dynamic cutting head technology virtually

eliminates taper and allows parts stacking

• Waterjet cutting can reduce costly

secondary processes.

Increased accuracy over other

forms of cutting

Accuracy of + or - .005 achievable

• Kerf is .040” with clean, burr free edges.

• Zero Heat Affected Zone (HAZ)

maintaining machinability, weldability and

eliminated all heat related problems like

distortion, crystallization, hardening or

cracking.

• No tooling required, parts are easily

produced using existing CAD drawings.

Easily modified—perfect for prototypes.

• Maximize material yield with nesting

capabilities.

• Waterjet can cut holes that are smaller in

diameter than the material thickness

• Slightly oversized material can be re-cut to

proper dimensions—reclaiming lost

material from the scrap bin

Now Available

Our New Waterjet

Cutting System

Contact Our Sales Department

For More Info

Or Come In To Take A Look

1-800-526-1031

10300 Southeast Jennifer Street

Tel: 503-656-0901

Fax: 503-656-1985

www.marksmetal.com

The Flow Waterjet 75” x 290” Maximum Cutting Area

87,000 PSI Maximum Cutting Pressure

Dynamic Cutting Head for increased accuracy

CNC Manufacturing 10300 S.E. Jennifer Street ● Clackamas, Oregon 97015

Custom Machining, Precise Forming, Repetitive Rolling

& State-of-the-Art Waterjet Cutting

Cincinnati 12’ x 230 Ton

CNC controlled Brake Press

with autoform controls

Our CNC controlled Berthiez

Vertical Lathe that gives us

an in-house capacity of

12” to 144” diameter.

Roundo 6 1/2’ x 9/16”

CNC controlled Plate Rolls

Flow Waterjet 75” x 297” maximum cutting area

87,000 PSI maximum cutting pressure

dynamic cutting head for increased accuracy

Our Brouchure

Documents