Post on 03-Jan-2016
transcript
Phys 2180 Lecture (5)
Current and resistance and Direct current circuits
• INTRODUCTIONIn the past chapters we have been discussing interactions of electric charges “at rest” (electrostatic).
Now we are ready to study charges “in motion”.
An electric current consists of motion of charges charges from one region to another.
When this motion of charges takes place within a conductor that forms a closed path, the path is called an electric circuit.
ELECTRIC CURRENTS
THE ELECTRIC CURRENT
We can also define current through the area as the net charge flowing through the area per unit time.
dt
dQI
CURRENT (Electric Current) It is the rate of flow of electric charge through a cross-
sectional area.
Electric CurrentThe electric current is the amount of charge per unit time that passes through a surface that is perpendicular to the motion of the charges.
The SI unit of electric current is the ampere (A), after the French mathematician André Ampére (1775-1836). 1 A = 1 C/s. Ampere is a large unit for current. In practice milliampere (mA) and microampere (μA) are used.
.t
QI
4
OHM’S LAW:RESISTANCE AND RESISTORS
• RESISTANCE– The proportionality of J to E for a metallic
conductor at constant temperature was discovered by G.S. Ohm.
IRV
For Ohmic materials (those that obey Ohm’s law), the potential V is proportional to the current I.
The behavior will always trace a linear relationship.
A
LR
OHM’S LAW:RESISTANCE AND RESISTORS
• RESISTOR
A
LR
Current I enters a resistor R as shown. (a) Is the potential higher at point A or at point B? (b) Is the current greater at point A or at point B?
ELECTRIC POWER
VIdt
dWP
R
VRIVIP
22
Power dissipated in a conductor
Power dissipated in a resistor
A CIRCUIT is a closed conducting path current flow all the way around.
• The POWER is the work done per unit time or the time rate of energy transfer
EMF AND TERMINAL VOLTAGE
Ideal Emf SourceReal Battery
Electromotive Force (emf) Source It is a device that supplies electrical
energy to maintain a steady current in a circuit.
It is the voltage generated by a battery.
IrVab ε
εabV
RESISTORS INSERIES AND PARALLEL
nRRRR ...21eq
RESISTORS IN SERIES The magnitude of the charge is constant. Therefore, the
flow of charge, current I is also constant. The potential of the individual resistors are in general
different.
The equivalent resistance of resistors in series equals the sum of their individual resistances.
321)(
321)(
VVVV
IIII
Totalseries
Totalseries
As the current goes through the circuit, the charges must USE ENERGY to get through the resistor. So each individual resistor will get its own individual potential voltage). We call this voltage drop.
is
series
seriesTT
Totalseries
RR
RRRR
RIRIRIRI
IRVVVVV
321
332211
321)(
)(
;Note: They may use the terms “effective” or “equivalent” to mean TOTAL!
Series Resistors and Voltage Division (1)
10
Parallel Resistors and Current Division (1)Parallel Resistors and Current Division (1)• Parallel wiring means that the devices are connected in such a way
that the same voltage is applied across each device.
• Multiple paths are present.
• When two resistors are connected in parallel, each receives current from the battery as if the other was not present.
• Therefore the two resistors connected in parallel draw more current than does either resistor alone.
321
321
321
321
1111
)(
;
RRRR
R
V
R
V
R
V
R
VR
VIIIII
IRVVVVV
p
parallel
parallelT
Total
R3
i iP RR
11
I3
11
RESISTORS INSERIES AND PARALLEL
Combinations of Resistors The 8.0- and 4.0-
resistors are in series and can be replaced with their equivalent, 12.0
The 6.0- and 3.0- resistors are in parallel and can be replaced with their equivalent, 2.0
These equivalent resistances are in series and can be replaced with their equivalent resistance, 14.0
13
QuestionCalculate the total resistance of a 4 and 6 ohm resistor connected (a) in series, (b) in parallel.
(a) series
RT = R1 + R2
= 4 Ω + 6 Ω= 10 Ω
(b) parallel
1 / RT = 1 / R1 + 1 / R2
= 1 / (4 Ω) + 1 / (6 Ω)= 0.2500 + 0.1666= 0.4166
= 1 / RT !!!!
and so RT = 1 / 0.4166= 2.4 Ω 14
Calculate the total resistance of the two circuits shown below:
Calculate the parallel section first1 / R1+2 = 1 / R1 + 1 / R2
= 1 / (2 Ω) + 1 / (5 Ω)= 0.5000 + 0.2000= 0.7000R1+2 = 1.429 Ω
Add in series resistanceRT = 5.429 Ω
= 5.43 Ω (to 3sf)
4 Ω
2 Ω
5 Ω
1.
12 Ω
8 Ω5 Ω
2.
Calculate the series section first5 Ω + 8 Ω = 13 Ω
Calculate 13 Ω in parallel with 12 Ω 1 / RT = 1 / R1 + 1 / R2
= 1 / (13 Ω) + 1 / (12 Ω)= 0.07692 + 0.08333= 0.16025RT = 6.2402 Ω= 6.24 Ω (to 3sf) 15
The heating effect of an electric current• When an electric current flows through an electrical
conductor the resistance of the conductor causes the conductor to be heated.
• This effect is used in the heating elements of various devices like those shown below:
Heating effect of resistance Phet
16
Electric Power,P.
time
EnergyP
Since the electrical energy is charge times voltage (QV), the above equation becomes,
.t
QVP
Since the current is charge flow per unit time (Q/t), the above equation becomes,
.VIVt
Q
t
QVP
Since V = IR, the above equation can also be written as,
.2
2
R
VRIIVP SI Unit of Power: watt(W)
17
Power and resistanceRevision of previous work
When a potential difference of V causes an electric current I to flow through a device the electrical energy converted to other forms in time t is given by:
E = I V t
but: power = energy / time
Therefore electrical power, P is given by:
P = I V
18
The definition of resistance: R = V / I
rearranged gives: V = I R
substituting this into P = I V gives:
P = I 2 R
Also from: R = V / I
I = V / R
substituting this into P = I V gives:
P = V 2 / R
19
Question 1Calculate the power of a kettle’s heating element of resistance 18Ω when draws a current of 13A from the mains supply.
P = I 2 R
= (13A)2 x 18Ω
= 169 x 18
= 3042W
or = 3.04 kW
20
Question 2Calculate the current drawn by the heating element of an electric iron of resistance 36Ω and power 1.5kW.
P = I 2 R gives:
I 2 = P / R
= 1500W / 36 Ω
= 41.67
= I 2 !!!!
therefore I = √ ( 41.67)
= 6.45 A
21
Emf and internal resistance Emf, electromotive force (ε):
The electrical energy given per unit charge by the power supply.
Internal resistance (r):
The resistance of a power supply, also known as source resistance.
It is defined as the loss of potential difference per unit current in the source when current passes through the source.
ε = E
Q
22
Equation of a complete circuitThe total emf in a complete circuit is equal to the total pds.
Σ (emfs) = Σ (pds)
For the case opposite:
ε = I R + I r
or
ε = I ( R + r )
23
Question 2Calculate the current drawn from a battery of emf 1.5V whose terminal pd falls by 0.2V when connected to a load resistance of 8Ω.
ε = I R + I r
where I r = lost volts = 0.2V
1.5 V = (I x 8 Ω) + 0.2V
1.5 – 0.2 = (I x 8)
1.3 = (I x 8)
I = 1.3 / 8
current drawn = 0.163 A
24
Question 3Calculate the terminal pd across a power supply of emf 2V, internal resistance 0.5Ω when it is connected to a load resistance of 4Ω.
ε = I R + I r
where I R = terminal pd
2 V = (I x 4 Ω) + (I x 0.5 Ω )
2 = (I x 4.5)
I = 2 / 4.5
= 0.444 A
The terminal pd = I R
= 0.444 x 4
terminal pd = 1.78 V
25
Single cell circuit rules1. Current drawn from the cell: I = cell emf
total circuit resistance
2. PD across resistors in SERIES with the cell: V = cell current x resistance of each resistor
3. Current through parallel resistors: I = pd across the parallel resistors
resistance of each resistor
26
Single cell questionTotal resistance of the circuit= 8 Ω in series with 12 Ω in parallel with 6 Ω= 8 + 5.333 = 13.333 Ω
Total current drawn from the battery = V / RT
= 9V / 13.333 Ω= 0.675 Apd across 8 Ω resistor = V8 = I R8
= 0.675 A x 8 Ω = 5.40 Vtherefore pd across 6 Ω (and 12 Ω) resistor, V6 = 9 – 5.4pd across 6 Ω resistor = 3.6 V Current through 6 Ω resistor = I6 = V6 / R6 = 3.6 V / 6 Ω current through 6 Ω resistor = 0.600 A
8 Ω
9 V
12 Ω
Calculate the potential difference across and the current through the 6 ohm resistor in the circuit below.
27