Post on 22-Jun-2020
transcript
Physics 6A
Work and Energy examples
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
Work and Energy
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
Energy comes in many forms. We will most often encounter two kinds of energy:
Kinetic Energy – Energy of Motion. Any moving object has kinetic energy.
The formula is KE = ½ mv2
Potential Energy – Stored Energy. There will be several types of potential energy:
* Gravitational – Energy stored by lifting an object above the earth. We will have a
more robust formula later, but for now: Ugrav = mgh
* Elastic – Energy stored by stretching or compressing a spring.
The formula is Uelastic = ½ kx2
* Electric – Energy stored by charges in an electric field. We will see this next quarter.
Work and Energy
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
Work is energy transferred to a moving object when a force acts on it. To do work, the
force must line up with the motion of the object. Perpendicular forces do no work.
We will have two formulas involving work.
W = Fdcos(θ)
W = ΔKE
Our main concept that ties it all together is Conservation of Energy. This says that
the total energy of a system does not change. We can write down a formula that accounts for all the forms of energy:
KEi + Ui + WNC = KEf + Uf
This will be the template for most of the problems you will do involving energy.
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
Example: A 100kg box (initially at rest) is pushed across a horizontal floor by a force of 400N. If the coefficients of friction are μk=0.2 and μs=0.4, find the total work done on the box and the final speed when the box is pushed 10m.Assume the applied force is horizontal.
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
Example: A 100kg box on a horizontal floor (initially at rest) is pushed by a force of 400N, applied downward at an angle of 30°.If the coefficients of friction are μk=0.2 and μs=0.4, find the total work done on the box. Does the box move?
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
Example: A 100kg box is released from rest at the top of a frictionless 10-meter high ramp that makes an angle of 30° with the horizontal.
Find the final speed of the box when it reaches the bottom of the ramp.
Compare to the impact speed when the box is pushed over the edge and free-falls to the ground instead.
10m
30°
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
Example: A 100kg box is released from rest at the top of a 10-meter high ramp that makes an angle of 30° with the horizontal. Assume the coefficients of friction are μk=0.2 and μs=0.3.
Find the final speed of the box when it reaches the bottom of the ramp.
10m
30°
1) A boy exerts a force of 11.0N at 29.0 degrees above the horizontal on a 6.40kg sled. Find the work done by the
boy and the final speed of the sled after it moves 2.00m, assuming the sled starts with an initial speed of 0.500m/s
and slides horizontally without friction.
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
1) A boy exerts a force of 11.0N at 29.0 degrees above the horizontal on a 6.40kg sled. Find the work done by the
boy and the final speed of the sled after it moves 2.00m, assuming the sled starts with an initial speed of 0.500m/s
and slides horizontally without friction.
29°
F=11N
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
1) A boy exerts a force of 11.0N at 29.0 degrees above the horizontal on a 6.40kg sled. Find the work done by the
boy and the final speed of the sled after it moves 2.00m, assuming the sled starts with an initial speed of 0.500m/s
and slides horizontally without friction.
29°
F=11N
Initially the sled is moving at 0.5 m/s, so its kinetic energy is:
J8.05.0kg4.6mvK2
sm
212
21
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
1) A boy exerts a force of 11.0N at 29.0 degrees above the horizontal on a 6.40kg sled. Find the work done by the
boy and the final speed of the sled after it moves 2.00m, assuming the sled starts with an initial speed of 0.500m/s
and slides horizontally without friction.
29°
F=11N
Initially the sled is moving at 0.5 m/s, so its kinetic energy is:
J8.05.0kg4.6mvK2
sm
212
21
Next we can find the work done by the boy’s pull, and add
that to the kinetic energy. Remember – work always equals
the change in the kinetic energy.
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
1) A boy exerts a force of 11.0N at 29.0 degrees above the horizontal on a 6.40kg sled. Find the work done by the
boy and the final speed of the sled after it moves 2.00m, assuming the sled starts with an initial speed of 0.500m/s
and slides horizontally without friction.
29°
F=11N
The force is not aligned with the motion, so we
need to use the x-component to get the work.
J24.19m229cosN11W
dcosFW
Initially the sled is moving at 0.5 m/s, so its kinetic energy is:
J8.05.0kg4.6mvK2
sm
212
21
Next we can find the work done by the boy’s pull, and add
that to the kinetic energy. Remember – work always equals
the change in the kinetic energy.
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
1) A boy exerts a force of 11.0N at 29.0 degrees above the horizontal on a 6.40kg sled. Find the work done by the
boy and the final speed of the sled after it moves 2.00m, assuming the sled starts with an initial speed of 0.500m/s
and slides horizontally without friction.
29°
F=11N
The force is not aligned with the motion, so we
need to use the x-component to get the work.
J24.19m229cosN11W
dcosFW
Initially the sled is moving at 0.5 m/s, so its kinetic energy is:
J8.05.0kg4.6mvK2
sm
212
21
Next we can find the work done by the boy’s pull, and add
that to the kinetic energy. Remember – work always equals
the change in the kinetic energy.
Now the total KE is 20.04J. Use this to solve for the new speed:
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
1) A boy exerts a force of 11.0N at 29.0 degrees above the horizontal on a 6.40kg sled. Find the work done by the
boy and the final speed of the sled after it moves 2.00m, assuming the sled starts with an initial speed of 0.500m/s
and slides horizontally without friction.
29°
F=11N
The force is not aligned with the motion, so we
need to use the x-component to get the work.
J24.19m229cosN11W
dcosFW
Initially the sled is moving at 0.5 m/s, so its kinetic energy is:
J8.05.0kg4.6mvK2
sm
212
21
Next we can find the work done by the boy’s pull, and add
that to the kinetic energy. Remember – work always equals
the change in the kinetic energy.
Now the total KE is 20.04J. Use this to solve for the new speed:
sm2
221
5.2vkg4.6
)J04.20(2v
J04.20mvK
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
2) A spring-loaded toy gun is used to shoot a ball of mass m=1.50kg straight up in the air, as shown in the figure.
The spring has a spring constant of k=667N/m. If the spring is compressed a distance of 25.0cm from its
equilibrium position y=0 and then released, find the ball’s maximum height hmax(measured from the equilibrium
position of the spring.) There is no air resistance, and the ball never touches the inside of the gun. Assume that all
movement occurs in a straight line up and down along the y-axis.
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
2) A spring-loaded toy gun is used to shoot a ball of mass m=1.50kg straight up in the air, as shown in the figure.
The spring has a spring constant of k=667N/m. If the spring is compressed a distance of 25.0cm from its
equilibrium position y=0 and then released, find the ball’s maximum height hmax(measured from the equilibrium
position of the spring.) There is no air resistance, and the ball never touches the inside of the gun. Assume that all
movement occurs in a straight line up and down along the y-axis.
We will use conservation of energy for this one. Notice that the picture already has y=0
defined for us at the top of the tube (this is also the equilibrium position of the spring).
[1]
[3]
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
2) A spring-loaded toy gun is used to shoot a ball of mass m=1.50kg straight up in the air, as shown in the figure.
The spring has a spring constant of k=667N/m. If the spring is compressed a distance of 25.0cm from its
equilibrium position y=0 and then released, find the ball’s maximum height hmax(measured from the equilibrium
position of the spring.) There is no air resistance, and the ball never touches the inside of the gun. Assume that all
movement occurs in a straight line up and down along the y-axis.
We will use conservation of energy for this one. Notice that the picture already has y=0
defined for us at the top of the tube (this is also the equilibrium position of the spring).
At the beginning (I will call this position [1]) the energy of the system is all potential – the
ball is not moving so K=0. We need to account for the compression of the spring, as
well as the gravitational potential energy of the ball:
[1]
[3]
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
2) A spring-loaded toy gun is used to shoot a ball of mass m=1.50kg straight up in the air, as shown in the figure.
The spring has a spring constant of k=667N/m. If the spring is compressed a distance of 25.0cm from its
equilibrium position y=0 and then released, find the ball’s maximum height hmax(measured from the equilibrium
position of the spring.) There is no air resistance, and the ball never touches the inside of the gun. Assume that all
movement occurs in a straight line up and down along the y-axis.
We will use conservation of energy for this one. Notice that the picture already has y=0
defined for us at the top of the tube (this is also the equilibrium position of the spring).
At the beginning (I will call this position [1]) the energy of the system is all potential – the
ball is not moving so K=0. We need to account for the compression of the spring, as
well as the gravitational potential energy of the ball:
J17.17E
m25.08.9kg5.1m25.0667E
mgykyE
1
s
m2mN
21
1
1212
11
2
[1]
[3]
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
2) A spring-loaded toy gun is used to shoot a ball of mass m=1.50kg straight up in the air, as shown in the figure.
The spring has a spring constant of k=667N/m. If the spring is compressed a distance of 25.0cm from its
equilibrium position y=0 and then released, find the ball’s maximum height hmax(measured from the equilibrium
position of the spring.) There is no air resistance, and the ball never touches the inside of the gun. Assume that all
movement occurs in a straight line up and down along the y-axis.
We will use conservation of energy for this one. Notice that the picture already has y=0
defined for us at the top of the tube (this is also the equilibrium position of the spring).
At the beginning (I will call this position [1]) the energy of the system is all potential – the
ball is not moving so K=0. We need to account for the compression of the spring, as
well as the gravitational potential energy of the ball:
J17.17E
m25.08.9kg5.1m25.0667E
mgykyE
1
s
m2mN
21
1
1212
11
2
[1]
[3]
Next we can look at position [3], at the high point. It’s all gravitational potential energy there, since the
ball is not moving (K=0) and the spring is at equilibrium (Uelastic = 0).
max3 mghE
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
2) A spring-loaded toy gun is used to shoot a ball of mass m=1.50kg straight up in the air, as shown in the figure.
The spring has a spring constant of k=667N/m. If the spring is compressed a distance of 25.0cm from its
equilibrium position y=0 and then released, find the ball’s maximum height hmax(measured from the equilibrium
position of the spring.) There is no air resistance, and the ball never touches the inside of the gun. Assume that all
movement occurs in a straight line up and down along the y-axis.
We will use conservation of energy for this one. Notice that the picture already has y=0
defined for us at the top of the tube (this is also the equilibrium position of the spring).
At the beginning (I will call this position [1]) the energy of the system is all potential – the
ball is not moving so K=0. We need to account for the compression of the spring, as
well as the gravitational potential energy of the ball:
J17.17E
m25.08.9kg5.1m25.0667E
mgykyE
1
s
m2mN
21
1
1212
11
2
[1]
[3]
Next we can look at position [3], at the high point. It’s all gravitational potential energy there, since the
ball is not moving (K=0) and the spring is at equilibrium (Uelastic = 0).
max3 mghE
Conservation of energy says that the total energy should be the same at both points, so E1 = E3 = 17.17J
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
2) A spring-loaded toy gun is used to shoot a ball of mass m=1.50kg straight up in the air, as shown in the figure.
The spring has a spring constant of k=667N/m. If the spring is compressed a distance of 25.0cm from its
equilibrium position y=0 and then released, find the ball’s maximum height hmax(measured from the equilibrium
position of the spring.) There is no air resistance, and the ball never touches the inside of the gun. Assume that all
movement occurs in a straight line up and down along the y-axis.
We will use conservation of energy for this one. Notice that the picture already has y=0
defined for us at the top of the tube (this is also the equilibrium position of the spring).
At the beginning (I will call this position [1]) the energy of the system is all potential – the
ball is not moving so K=0. We need to account for the compression of the spring, as
well as the gravitational potential energy of the ball:
J17.17E
m25.08.9kg5.1m25.0667E
mgykyE
1
s
m2mN
21
1
1212
11
2
[1]
[3]
Next we can look at position [3], at the high point. It’s all gravitational potential energy there, since the
ball is not moving (K=0) and the spring is at equilibrium (Uelastic = 0).
max3 mghE
Conservation of energy says that the total energy should be the same at both points, so E1 = E3 = 17.17J
m17.1
8.9kg5.1
J17.17h
J17.17mgh
2s
mmax
max
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
3) A block of mass m1= 2.40kg is connected to a second block of mass m2=1.80kg, as shown on the board. When
the blocks are released from rest, they move through a distance d=0.500m, at which point m2 hits the floor. Give
that the coefficient of kinetic friction between m1 and the horizontal surface is μk=0.450, find the speed of the
blocks just before m2 lands.
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
3) A block of mass m1= 2.40kg is connected to a second block of mass m2=1.80kg, as shown on the board. When
the blocks are released from rest, they move through a distance d=0.500m, at which point m2 hits the floor. Give
that the coefficient of kinetic friction between m1 and the horizontal surface is μk=0.450, find the speed of the
blocks just before m2 lands.
We can use conservation of energy. Initially nothing is moving, so K=0
and we only have gravitational potential energy.
gdmghmE 21i
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
3) A block of mass m1= 2.40kg is connected to a second block of mass m2=1.80kg, as shown on the board. When
the blocks are released from rest, they move through a distance d=0.500m, at which point m2 hits the floor. Give
that the coefficient of kinetic friction between m1 and the horizontal surface is μk=0.450, find the speed of the
blocks just before m2 lands.
We can use conservation of energy. Initially nothing is moving, so K=0
and we only have gravitational potential energy.
gdmghmE 21i
Just before the block lands, both blocks are moving so we will have
kinetic energy, as well as potential energy for block 1 only (block 2 is
now at y=0). Also note that both blocks move at the same speed.
2212
11f vmmghmE
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
3) A block of mass m1= 2.40kg is connected to a second block of mass m2=1.80kg, as shown on the board. When
the blocks are released from rest, they move through a distance d=0.500m, at which point m2 hits the floor. Give
that the coefficient of kinetic friction between m1 and the horizontal surface is μk=0.450, find the speed of the
blocks just before m2 lands.
We can use conservation of energy. Initially nothing is moving, so K=0
and we only have gravitational potential energy.
gdmghmE 21i
Just before the block lands, both blocks are moving so we will have
kinetic energy, as well as potential energy for block 1 only (block 2 is
now at y=0). Also note that both blocks move at the same speed.
2212
11f vmmghmE
In the absence of friction, we would just set these energies equal. We must account for friction by finding the work
done by friction, and adding it to the initial energy. Note: this work will be negative, so we will end up with less
energy than we started with, as expected (kinetic friction will always take energy away from the system).
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
3) A block of mass m1= 2.40kg is connected to a second block of mass m2=1.80kg, as shown on the board. When
the blocks are released from rest, they move through a distance d=0.500m, at which point m2 hits the floor. Give
that the coefficient of kinetic friction between m1 and the horizontal surface is μk=0.450, find the speed of the
blocks just before m2 lands.
We can use conservation of energy. Initially nothing is moving, so K=0
and we only have gravitational potential energy.
gdmghmE 21i
Just before the block lands, both blocks are moving so we will have
kinetic energy, as well as potential energy for block 1 only (block 2 is
now at y=0). Also note that both blocks move at the same speed.
2212
11f vmmghmE
In the absence of friction, we would just set these energies equal. We must account for friction by finding the work
done by friction, and adding it to the initial energy. Note: this work will be negative, so we will end up with less
energy than we started with, as expected (kinetic friction will always take energy away from the system).
dgmW
1dgmW
180cosdFW
1kfric
1kfric
fricfric
The friction work is negative because the
force always opposes the motion (that is
why the angle is 180 degrees).
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
3) A block of mass m1= 2.40kg is connected to a second block of mass m2=1.80kg, as shown on the board. When
the blocks are released from rest, they move through a distance d=0.500m, at which point m2 hits the floor. Give
that the coefficient of kinetic friction between m1 and the horizontal surface is μk=0.450, find the speed of the
blocks just before m2 lands.
We can use conservation of energy. Initially nothing is moving, so K=0
and we only have gravitational potential energy.
gdmghmE 21i
Just before the block lands, both blocks are moving so we will have
kinetic energy, as well as potential energy for block 1 only (block 2 is
now at y=0). Also note that both blocks move at the same speed.
2212
11f vmmghmE
In the absence of friction, we would just set these energies equal. We must account for friction by finding the work
done by friction, and adding it to the initial energy. Note: this work will be negative, so we will end up with less
energy than we started with, as expected (kinetic friction will always take energy away from the system).
dgmW
1dgmW
180cosdFW
1kfric
1kfric
fricfric
The friction work is negative because the
force always opposes the motion (that is
why the angle is 180 degrees).
Finally we just set our final energy equal to the initial energy, plus the (negative) friction work:
sm
2121
1k22
1k22
2121
fricif
3.1vmm
dgmgdmv
dgmgdmvmm
WEE
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
4) A 95.0 kg diver steps off a diving board and drops into the water 3.00m below. At some depth d below the
water’s surface, the diver comes to rest. If the non-conservative work done on the diver is Wnc= -5120J, what is
the depth ,d?
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
4) A 95.0 kg diver steps off a diving board and drops into the water 3.00m below. At some depth d below the
water’s surface, the diver comes to rest. If the non-conservative work done on the diver is Wnc= -5120J, what is
the depth ,d?
We will use conservation of energy. First we must define our coordinate system.
Using y=0 at the lowest point achieved by the diver, we have the following
expressions for the initial and final energy:
0)0(mgE
)hd(mgE
f
i
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
4) A 95.0 kg diver steps off a diving board and drops into the water 3.00m below. At some depth d below the
water’s surface, the diver comes to rest. If the non-conservative work done on the diver is Wnc= -5120J, what is
the depth ,d?
We will use conservation of energy. First we must define our coordinate system.
Using y=0 at the lowest point achieved by the diver, we have the following
expressions for the initial and final energy:
0)0(mgE
)hd(mgE
f
i
Notice that the kinetic energy is zero in both places because the speed is zero.
The final energy will be the non-conservative work plus the initial energy:
J5120)hd(mg0
WEE ncif
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB
4) A 95.0 kg diver steps off a diving board and drops into the water 3.00m below. At some depth d below the
water’s surface, the diver comes to rest. If the non-conservative work done on the diver is Wnc= -5120J, what is
the depth ,d?
We will use conservation of energy. First we must define our coordinate system.
Using y=0 at the lowest point achieved by the diver, we have the following
expressions for the initial and final energy:
0)0(mgE
)hd(mgE
f
i
Notice that the kinetic energy is zero in both places because the speed is zero.
The final energy will be the non-conservative work plus the initial energy:
J5120)hd(mg0
WEE ncif
We can solve this for (d+h), then subtract out the given value for h.
m5.2m0.3m5.5d
m5.58.9kg95
J5120)hd(
J5120)hd(mg0
2s
m
Prepared by Vince Zaccone
For Campus Learning
Assistance Services at UCSB