Post on 21-Feb-2022
transcript
CONNECTOR SUBSEA SOLUTIONSHead office: Kokstadflaten 17, 5257 Kokstad, NorwayLocations in: Brazil, UK, Croatia & Bosnia
www.connectorsubsea.com // mail@connectorsubsea.com
+47 99 70 11 11 // connector-subsea-solutions
Product ID: 20502-0320-01 // Page: 1/2
PRODUCT GROUP
PIPELINE REPAIR & TIE-IN
PIPELINE COATING REMOVAL TOOLS
PRODUCT DESCRIPTION
Our Pipeline Coating Removal Tool enables the removal of all coatings including FBE, without any risk to damaging the parent pipeline. This assurance is critical when using the exposed pipe as an interface for subsea intervention. Deploying a patented cutting head technology, the tool can follow the contour of the pipe regardless of pipeline tolerances and ovality, pro-viding full assurance that all coating is removed. A separate module can remove the weld bead if necessary.Suitable for both horizontal and vertical application, the tool is light weight and easy to mobilize. As a fully remote system the tool ensures safe, reliable, controllable and efficient subsea operation up to 3000mwd while also providing the very best possible surface finish which is qualified for use with MORGRIP Clamps and Connectors.
CAPACITIES
Pipeline size 4-14in 10-20in 18-36in
Axial stroke (length of coating removal) 1300 mm
Radial stroke (dept of coating removal) 35 mm
Allowable slope for operation 30 deg
Water depth (m) 3000 m
DIMENSIONS & WEIGHT
Dimensions (HxWxD) 4-14in: 1,7 x 1,6x 2,7 m 10-20in: 2,0 x 2,1 x 2,7 m 18-36in: 2.8 x 2.9 x 3.0 m
Mass of Tool 4-14in: 1445 kg 10-20in: 1926 kg 18-36in: 3154 kg
Continued on next page >>
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
DWG REV:SCALE:
DESCRIPTION:
TITLE:
SHEET:
PROJECT:
WEIGHT:
This drawing is the property of CONNECTOR SUBSEA SOLUTIONS. It must not be copied, altered or distribued in any way without prior consent from the company!
PROJECTION:
3154.3 kg
18513 - Coating Removal Tool Development
Coating Removal Tool 36inGeneral Arrangement (Range 24-36in)
1 of 1 11 : 20FORMAT:
A2 IDUDRAWN BY:
IDUCREATED BY:
GADRAWING TYPE:
PN114040
PART NUMBER / DRAWING NUMBER:
1 IDU Work in progress
REV DATE COMMENT RESPONSIBLE STATE
1710
2784
2440
InterfaceItem Description
A 4 Line Stab and Recepticle (x3)
B ROV Grabber Bar
C Yellow lifting points (4x8t Yoke)
Weights
Name in Air Submerged
Coating Removal Tool 36in 3154 [kg] 2354 [kg]
2870
1991
603
,5
955
2233
1383
1019
Guiding Pipe Ø100/60Fixed at Both Ends
Lead Screw Tr40x7
Pad 1
9
49
Pad 2
Centralizing Open Max.(Max.OD for gripping with Pad 1)
Centralizing Close Max.(Min.OD for gripping with Pad 2)
811
()
1829
1069
2972,5
955Tool Opening=
1272955
Spur Gear 2 is made of one piece (not welded)z=316m=4
Centralizer Lead Screw Tr40x7
1829
850
2679 27
56
1330
C
B
A
PRELIMINARY
2011
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
DWG REV:SCALE:
DESCRIPTION:
TITLE:
SHEET:
PROJECT:
WEIGHT:
This drawing is the property of CONNECTOR SUBSEA SOLUTIONS. It must not be copied, altered or distribued in any way without prior consent from the company!
PROJECTION:
3154.3 kg
18513 - Coating Removal Tool Development
Coating Removal Tool 36inGeneral Arrangement (Range 24-36in)
1 of 1 11 : 20FORMAT:
A2 IDUDRAWN BY:
IDUCREATED BY:
GADRAWING TYPE:
PN114040
PART NUMBER / DRAWING NUMBER:
1 IDU Work in progress
REV DATE COMMENT RESPONSIBLE STATE
1710
2784
2440
InterfaceItem Description
A 4 Line Stab and Recepticle (x3)
B ROV Grabber Bar
C Yellow lifting points (4x8t Yoke)
Weights
Name in Air Submerged
Coating Removal Tool 36in 3154 [kg] 2354 [kg]
2870
1991
603
,5
955
2233
1383
1019
Guiding Pipe Ø100/60Fixed at Both Ends
Lead Screw Tr40x7
Pad 1
9
49
Pad 2
Centralizing Open Max.(Max.OD for gripping with Pad 1)
Centralizing Close Max.(Min.OD for gripping with Pad 2)
811
()
1829
1069
2972,5
955Tool Opening=
1272955
Spur Gear 2 is made of one piece (not welded)z=316m=4
Centralizer Lead Screw Tr40x7
1829
850
2679 27
56
1330
C
B
A
PRELIMINARY
2011
CONNECTOR SUBSEA SOLUTIONSHead office: Kokstadflaten 17, 5257 Kokstad, NorwayLocations in: Brazil, UK, Croatia & Bosnia
www.connectorsubsea.com // mail@connectorsubsea.com
+47 99 70 11 11 // connector-subsea-solutions
Product ID: 20502-0320-01 // Page: 2/2
PIPELINE COATING REMOVAL TOOLSPIPELINE REPAIR & TIE-IN
DIMENSIONS & WEIGHT (CONTINUED)
Weight of tool in air 4-14in: 14 176N (1445 kgf) 10-20in: 18 894N (1926 kgf) 18-36in: 30 941N (3154 kgf)
Submerged weight of tool 4-14in: 11 503N (1142 kgf) 10-20in: 14 637N (1492kgf) 18-36in: 23 093N (2354 kgf)
INTERFACES
ROV operated Yes, compliant with CSS ROV skid and topside control system
ROV Interface Specification 4 Line stab and Receptacle, Ø35, 10k, API 17D (x3)
Max. working pressure 207 bar /3000 psi
Flow >38 l/min
Hydraulic oil Shell Tellus S2 22/32 (typical) NAS8/ISO 4406 19/17/14
ROV grabber bars Yes
Lifting points Eye bolt w/swivel WLL 5/8 t (4 pcs.) on tool frame Supplied with wire rope sling w/master link WLL 3,5t 30o DNVGL-ST-E271 Installation Heave Compensated Deck Crane & WROV
ADDITIONAL INFORMATION
Design code DNVGL 2.7-3 Portable offshore units DNVGL-OS-C101 Design of offshore steel structures
Operation Class DNV 2.7-3 R60-Sxx
Buoyancy application Yes. Note that buoyancy is not delivered with tool
Coating NORSOK 7B, Marine epoxy paint system
Cathodic protection Yes
Packing Container
02 // Offshore mobilisation
03 // ROV footage of subsea application
01 // Factory acceptance testing