Power² & Light²

transcript

Power² & Light²Version

A complete unit with maximum

• Objectives:Pre-implant surgery,

implantology,maxillofacial surgeries and conventional treatments

• Objectives:Pre-implant surgery,

implantology,maxillofacial surgeries and conventional treatments

• I-Surge micro-motor• Piezotome 2 LED handpiece• Newtron LED handpiece• Ultrasonic connector: The Piezotome or Newtron

handpieces are automatically recognized by the unit

The Implant Center 2 combines the best of ultrasonic and motor technologies for:

- Pre-implant surgery,

- Implant surgery,

- Implant maintenance,

- Oral maxillofacial surgeries

Ultrasonic technology: Ultrasonic technology:

Automatic frequency : 28-36 kHz

Controlled amplitude

Real-time power adjustment

Technology

Motor technology:Brushless

Rotation speed: 100 – 40 000 rpm

6 N.cm up to 24 000 rpm

Contra-angle ratio: 20:1

Rotation speed at instrument end:

[5 – 2 000 rpm]

Motor technology:Brushless

Rotation speed: 100 – 40 000 rpm

6 N.cm up to 24 000 rpm

Contra-angle ratio: 20:1

Rotation speed at instrument end:

[5 – 2 000 rpm]

Ultrasonics Piezotome mode: modulated piezo signal (modulation)

Newtron mode: piezo sinusoïdal signal

Rapidity: fine, fast, precise and effortlessselective cut thanks to ultra-sharp, robust

andresistant Piezotome tips.Comfort: Atraumatic treatments (no bone loss, no bleeding), fast healing, and greatly reduced post-operative pain.

Safety: preservation of soft tissue (nerves, membranes,

arteries).

Ultrasonic high power generator

New touch-sensitive screen

- Giant 5.7’’ screen,

- Touch-sensitive screen (even with gloves),

- Highlighting of the activated function for improved visibility.

Screen zones

Technology zone

Piezotome mode activatedIrrigation zone

Power value zone

Mode zone

Options zone

Piezotome mode

Handpiece

Respect of soft tissue, fast healing and greatly reduced post-operative pain

• Boosted (up to 60 W output power) for a much quicker procedure,

• It is up to three times more powerful than Piezotome/Implant Center 1

• Equipped with the latest high luminosity generation LEDs, • Highly resistant,• Does not induce overheating or extraneous vibration,• Can be sterilized, • Easy to clean (the nozzle can be detached).

To perform successful, fast and worry-free delicate

pre-implant surgical procedures:- fine osteotomy,- osteoplasty,- bone grafting,- sinus lift,- extraction,- crown lengthening- …

Piezotome mode:Clinical aspects

Piezotome mode

Irrigation

flow rate

Irrigation

flow rate

PurgePurge

Irrigation activation/ deactivation

Fine power adjustmentFine power adjustment Power settings

referring to bone density classification

Power settings referring to bone density classification

LED LED

Progressive footswitch

Save ModeSave Mode

Piezotome 2 Tips

Piezotome tips version 1 Piezotome tips version 2

The tips dedicated to Piezotome 2 and Implant Center 2 are easily recognizable by:

- their large base,- their “II” laser mark.

Piezotome 2 Tips

- Stainless-steel medical grade alloy with specific thermic and surface treatments, polishing, etc.

- Synthetic diamond coating with special processing.

- Clean, fast and effortless cut.

- Ultra-sharp, robust and resistant tips.

- Stainless-steel medical grade alloy with specific thermic and surface treatments, polishing, etc.

- Synthetic diamond coating with special processing.

- Clean, fast and effortless cut.

- Ultra-sharp, robust and resistant tips.

NEW PACK design!

I-SURGE mode

4 modes with complete customization possible4 modes with complete customization possible

Handpiece motor (contra-angle, straight, multiplier)

Rotation speedRotation speed

TorqueTorque

Save modeSave mode

Progressive or ON/OFF footswitch

Rotation direction Audible signal

Forward/reverse drive selected through the footswitch

Rotation direction Audible signal

Forward/reverse drive selected through the footswitch

Fast and simple settings adjustments: Modes

1. Select your program.

Marking

implant site

1200 Rpm

80 N.Cm

80 ml/min

Pilot drill

800 Rpm

80 N.cm

100 ml/min

Site preparation

Tapping

15 Rpm

40 N.cm

100 ml/min

Screwing

30 Rpm

40 N.cm

0 ml/min

I-SURGE: four pre-set modes

P1, P2, P3: Direct access to RpmP4: Direct access to Ncm

Fast and simple settings adjustments: CA

1. Select your program.2. Select/change your contra-angle ratio.

CA ratio selection

Standard Multiplier Handpiece/ contra-angle

Direct Handpiece/ contra-angle

Standard Divider Handpiece/ contra-angle

20:1Presentation of the most common contra-angle ratios (multiplier, direct, divider).If the ratio is not pre-defined, insert your own ratio by pressing this button.

CA ratio selection

Handpiece SettingHandpiece Setting

20:1Set your own contra-angle ratio, whether it ismultiplier,direct, ordivider.

Fast and simple settings adjustments: Rpm

1. Select your program.2. Select/change your contra-angle ratio.3. Select the speed rotation needed by:-Pressing the + and – buttons on P1, P2 and P3 only,- Pressing the Rpm button.

Fast and simple settings adjustments: Rpm

Rpm settingRpm setting

Fast and simple settings adjustments: Ncm

1. Select your program.2. Select/change your contra-angle ratio.3. Select the speed rotation needed by:-Pressing the + and – buttons on P1, P2 and P3 only,- Pressing the Rpm button.4. Select the torque needed by:-Pressing the + and – buttons on P4 mode only,-Pressing the Ncm button.

I-SURGE mode

Torque SettingTorque Setting

I-SURGE mode

1. Select your program.2. Select/change your contra-angle ratio.3. Select the speed rotation needed by:-Pressing the + and – buttons on P1, P2 and P3 only,- Pressing the Rpm button.4. Select the torque needed by:-Pressing the + and – buttons on P4 mode only,-Pressing the Ncm button.5. Increase/decrease/delete irrigation flow rate.6. Select the progressive or ON/OFF footswitch7. Save

NEWTRON mode

• Excellent visibility even in posterior areas,

• Cold light (6 000 – 7 000°K) for better tissue recognition,

• Ideal for working with loupes,

• Powerful (100 000 Lux), very long-lasting LEDs,

• Handpiece can be autoclaved at 134°C.

• Excellent visibility even in posterior areas,

• Cold light (6 000 – 7 000°K) for better tissue recognition,

• Ideal for working with loupes,

• Powerful (100 000 Lux), very long-lasting LEDs,

• Handpiece can be autoclaved at 134°C.

LED NEWTRON handpiece

NEWTRON mode:Clinical aspects

- Periodontal procedures (surgical, non-surgical)

- Endodontics

- Microsurgery (apicoectomies)

- Implant maintenance

- etc,…

NEWTRON MODE Delicate precision treatments

Prophylaxis - Scaling

H3 tip

Maintenance

PH2R tip

Endodontics

ET25 tip

S12-90ND tip

Periodontics

N°1S tip

EX1 tip PM1 tip

Surgical endodontics Conservative and restorative dentistryExcavation Prosthetic finishing

NEWTRON mode:Four power settings

Low power; low amplitude. Delicate treatments: Periodontics.

Medium power; medium amplitude. Precision treatments: Endodontics.

High power; high amplitude. Routine prophylaxis: Scaling.

Very high power; maximum amplitude. Special treatments: Crown loosening.

NEWTRON mode:Fine adjustment

Each mode (Soft – Medium - High – Boost) enables fine power adjustment from 1 to 10.

Ergonomics

Peristaltic pumps

• Silent-running pumps.• Extremely precise

irrigation flow.• No bone necrosis.• Easy to install irrigation

PiezoTouch™ footswitch

IrrigationIrrigation

ProgramsPrograms

PiezoTouch™

Progressive power regulation:

Ultrasonics and motor

PiezoTouch™

Progressive power regulation:

Ultrasonics and motor

Purge,

Rotation direction

Purge,

Rotation direction

Choice of instrumentChoice of instrument

Removable arch Removable arch

PiezoTouch™

D1 to D3, the ultrasonic power delivered will vary between D3 – (01) and the power selected by the user (mode and fine adjustment).

In D4 the ultrasonic power will only vary from 1 to 5 depending on the fine adjustment selected by the user.

In Newtron function, the ultrasonic power in progressive varies between 1 and 10 in each mode.

Optimal disinfection and asepsis

All accessories (cords, handpieces, motor, tips…) can be autoclaved at 134°C for 18 minutes.

Designed for use under the most demanding clinical conditions.

Clinical cases

Clinical casesComing soon!

Competition

FEATURES

Implant Center 2 Implant Center Surgisonic Moto INTRAsurg 1000 Air

Company SATELEC SATELEC ESACROM KAVO

Technology

Handpieces

Piezotome = Pre-implant surgery

I-SURGE = Implant surgeryNewtron = All conventional

treatments

Piezotome = Pre-implant surgery

I-SURGE = Implant surgeryNewtron = All conventional

treatments

Surgysonic2 = Pre-implant surgery

Moto = Implant surgery

Soniclex Bone --> Pre-implant surgery

SONICflex --> Scaling Air-driven

Maximum Output Power (measured)

60 Watts - Yield of Power 90% 20 Watts - Yield of Power 90% Not measured, average Weak

Autoclavable LED handpiece

YES (100 000 Lux) NO NO NO

PiezoTouch - progressivity in ultrasonics

YES NO NO NO

Frequency High: 28 000 - 36 000 Hz High: 28 000 - 36 000 Hz High: 24 000 - 32 000 Hz Low: 6 000 Hz

Linear tip movement

YESControlled and linear

Very precise and easy to control

YESControlled and linear

Very precise and easy to controlAVERAGE

NOVariability - Elliptical movement

Very hard to control

Very high precision YES YES NO NO

Cruise Control YES YES NO NO

Motor I-SURGE I-SURGE MOTO INTRAsurg 300 plus

Brushless motorUltrasonics

YESYES (Piezo)

YES (they claim)YES (Piezo)

YESNO (Sonic)

The widest speed rotation range on the market

YES100 - 40 000 rpm

NO200 - 40 000 rpm

NO300 - 40 000 rpm

Torque 6 N.cm 6 N.cm 3 N.cm (very low) 5.5 N.cmErgonomicsPumps 2 peristaltic pumps 2 peristaltic pumps 1 peristaltic pump 2 peristaltic pumps

Touch screenYES (very fine and easy

settings)NO NO NO

Multi-function footswitch

YES (new weighted footswitch) YES YES YES

Handpiece cord length 2m or 2.9m on option 2m 2m 2m

Power ultrasonics in version:

One device for a new approach to implantology

Power² & Light²

Documents