Post on 21-Jun-2018
transcript
Your climate solution center
www.centrumklima.plwww.centrumklima.pl
POLAND05-820 Piastów, 4 Noakowskiego streettel. +48 22 753 71 72fax +48 22 753 42 80
POLAND02-237 Warsaw, 7B Instalatorów streettel. +48 22 868 25 28fax +48 22 886 48 87
Centrum Klima S.A.
Products catalogue
Distributor
Centrum Klima S.A. Wieruchów05-850 Ożarów Mazowiecki, 144 Sochaczewska streetphone: +48 22 250 50 50fax: +48 22 250 50 60
klient@centrumklima.pl www.centrumklima.co.uk www.centrumklima.co.uk
Okladka_ANG_2012.06_grzbiet.indd1 1 2013-01-31 13:31:14
LOCATION MAPOutline map of Warsaw with access routesto Centrum Klima’s office and warehouse.
Poznańska
Świerkowa
Świerkow
a
Ogrodni
cza
Sochaczewska
Sochaczewska
PiotrkówekDuży
Poznańska
Giełda Bronisze
Wieruchów
Bronisze
Poznań
Warszawa
Stare Babice
WieruchówPoland05-850 Ożarów Mazowiecki, 144 Sochaczewska street phone: +48 22 250 50 50
fax: +48 22 250 50 60
Monday - Friday: 8 am - 4 pmSaturday: 8 am - 2 pm
Fundusze Europejskie – dla rozwoju innowacyjnej gospodarkiInwestujemy w waszą przyszłość
Obecnie realizujemy projekt współfinansowany przez Unię Europejską z Europejskiego Funduszu Rozwoju RegionalnegoPOIG.6.1 Etap II
1. Products, technical details and prices were included herein only for information purposes. They may change, for instance due to product upgrade, without prior notice and should not be understood as Centrum Klima’s direct off er. The company may not be held responsible for potential mistakes or inaccuracies which may arise herein.
2. The products and prices expressed herein do not include VAT and are not a business off er in the meaning of commercial law regulations. Centrum Klima reserves the right to alter the prices without any form of notifi cation.
3. All dimensions are expressed in millimetres unless stated otherwise.
Okladka_ANG_2012.06_grzbiet.indd2 2 2013-01-31 13:31:15
Centrum Klima – Products catalogue 3
6
8
9
10
11
12
13
14
15
16
17
18
21
22
23
30
31
32
35
36
37
38
39
40
41
42
43
45
46
47
48
49
50
51
52
53
54
55
56
58
59
60
61
63
64
65
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
CONTENTS
Coil pipe RZCoil pipe (stainless steel) RZN
90° bend B9/B9X60° bend B6/B6X 45° bend B4/B4X 30° bend B3/B3X 15° bend B1/B1X Sectional bend BS/BSX Segmented bend (stainless steel) BSNPressed reducer RC/RCXPressed reducer RCF/RCFXSymmetric segmented reducer RS/RSXSymmetrical reducers (stainless steel) RSNAsymmetrical segmented reducer RN/RNXSymmetric pipe–tee TS/TSX Symmetrical tee TSHF/TSHFXSymmetrical tee (stainless steel) TSN Colar saddle PS/PSX45° branching for round ducts PS4/PS4XBranching with net BUSBranching overlaying round/rectangulare duct CB/FBTwin bend TSY/TSYXCoupling V/VXCoupling (stainless steel) VN Sleeve VFSleeve (stainless steel) VFNDuct end cap D/DX/DXH Fitting end cap DF/DFHStraight branching IL/ILX45° cylindrical branching IL4/IL4XPressed straight branching ILR/ILRXNet straight branching SO
Aluminum flexible duct, non-insulated AF012Aluminum flexible duct, insulated AF013/AF019Non insulated flexible ducts AF012ECO
Insulated flexible ducts AF013ECO/ AF019ECO Aluminum flexible duct, non-insulated M0Aluminum flexible duct, insulated M0izo Semi flexible aluminum duct non - insulated S-FLEX® Flexible PVC duct POLYFLEX HEAVY DUTY Flexible PVC laminated duct COMBIFLEX Duct specifications
Single blade round damper DS/DSX Air-tight single-leaf round damper DSXSSingle-leaf round damper (stainless steel) DSNDuct damper type IRISBack draft damper RSKSingle blade rectangular damper PJMulti blade rectangular damper PWMulti blade damper PWGravity aluminum dampers PSE/PSK
Access door for a rectangular duct RDCleanout hatches KRInspection hatches on rectangular duct FADRound intake / exhauster KWO-ALRound intake / exhauster (CrNi steel) VLAGalvanized steel rectangular air
intake/exhauster CWAnodized aluminum rectangular air
intake / exhauster CWARoof rectangular air intake / exhauster type A WDP-ARoof rectangular air intake / exhauster type B WDP-BRoof air intake KRoof round air intake type C CDORoof circular air exhauster / intake type C WDO-CRoof circular air intake / exhauster type D WDO-D
ROUND DUCTS
FLEXIBLE DUCTS
DAMPERS
VENTILATION EQUIPMENT
– New product
ROUND FITTINGS
Centrum Klima – Products catalogue4
CONTENTS
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
104
106
107
112
113
114
115
116
117
118
119
120
120
120
120
Roof round air intake / exhauster HF/HNRound gravity ventilator WDCRoof base B-I, B-II, B-III PDRectangular roof base type A PD-PRectangular roof bases PD-SRectangular attenuating roof base PD-STRound duct filters OFKCircular duct filters FKOCasette filters FSAI grille (steel mesh) AIRectangular flexible duct connectors KEPCircular flexible connector pipes KEO-KPlenum box SRPlenum box SR-HB40Plenum box SR-SD-BPlenum box SR-SD-CRound connection DSPChimney Root Centrowent CA/CNChimney Root Rotoflex RTNChimney VH
Round acoustic silencers TAOFlexible round silencers TAO S-FLEXRectangular acoustic silencers TAPFlexible acoustic silencer TAE
Pipe clips for round ducts
OPO/OPOX OPO INOX/OPOX INOXMetal band clip CMMetal clip tape CMB/CMCNylon band clip CMNSupressing bands OMAssembly profile – galvanized W 2Assembly profile – galvanized W 105Assembly profile – galvanized W 106Assembly profile – galvanized W 107
Assembly profile – galvanized W 41L suspension profile with shock
absorbing rubber
Z suspension profile with shock
absorbing rubber
R / V suspension profile with shock
absorbing rubber
Ventilation duct clip
Screwed bar handle
Screwed bar
Anchor bush
Shock absorbing rubber RU-25Double screwed thread screw VDFSelf-drilling metal sheet screws
Self-drilling metal sheet screws
PAN-HEADTerminal DCC-14 sheet metal screws
Suspension profile to Akerman ceilings
Vergacol VG tightening mass
Zinc spray alucynk ALZN 600Acetic silicone
Acrylic silicone
PE assembly foam
NN galvanized nut
NK stainless steel nut
LN connecting nut
BB galvanized screw
BK stainless steel screw
WW enlarged galvanized washer
PES gasket
Temperature resistant gasket PESTDUH perforated tape
Type T angle console
Type T angle console (with diagonal bar)
Type B shape base
Self-adhesive nails / nails for welding GSAluminum insulation tape
Reinforced aluminum insulation tape
Universal repair tape
PVC installation tape
PP metalized tape
High temperature tape
120
121
121
122
122
122
123
123
123
124
124
124
125
125
125
126
126
127
127
128
128
128
128
129
129
129
130
130
131
131
132
133
134
134
135
135
136
136
SILENCERS
ASSEMBLY ACCESSORIES
Centrum Klima – Products catalogue 5
CONTENTS
AIR CURTAIN
FANS
137
137
138
138
139
139
140
141
142
142
142
143
143
143
144
144
144
145
146
147
148
149
150
153
DW galvanized duct profiles
H corners for duct profiles
Connectors LKK for ventilation elbow air fin
Stiffening steel cross - KUSStiffening disc DUStiffening galvanized pipe RUOFlange VKPKFlexible connector LEDamper mechanisms with a blockade
Elements for ventilation dampers
Damper mechanisms
Spiro damper mechanism
AC-006 damper mechanism
Damper mechanisms on bases
Damper mechanisms for quick installation
Multi leaf damper bolts
Sleeves
Zinc-plated 12x12 mesh
Thermal insulation adhesive mat MSTRound pipe insulation SLEEVE
LF 2000 welder
Air curtain RM
DJT CIRCULAR DUCT FAN
ON/OFF Actuators TD
TOOLS
ACTUATORS
Proportional actuators TA
Presostat TP33B
Diameter range
Collective package sizes P
Index
Notes
154
155
156
157
158
160
INSULATION MATERIALS
PRODUCTION MATERIALS
PRESOSTAT
TOLERANCE
NOTES
COLLECTIVE PACKAGE DIMENSIONS
ALPHABETICAL INDEXABC
Centrum Klima – Products catalogue6
Round ducts
COIL PIPE RZ
Z wzmacniającymprzetłoczeniemzewnętrznym
D
L
LT
TD
≥ 25
0
With external embossment
Spiral pipes Spiro® are made of thin galvanized steel and their standard length is 3 m. Pipes of 250 mm or more in diameter have external em-bossment. Galvanizing is Z200-275 class, double sided coating has the density of 200-275 g/m2.
DESCRIPTION
m /h3[ [50
50
10
5
1
0,5
0,1
0,05
0,02100
100
200
500 1000 5000 10000
Wy datek powietrza
Stra
ta c
iś ni
enia
p
[Pa]
t
50000
[Pa/m]80
100
125
160
200
250
315
2
400
500
630
800
1000
5
10
1 5
20
V [m/s]
Śr. nominalna [mm]nominal diameter [mm]
air volume
pres
sure
loss
p, [
Pa]
Product characteristic:hot galvanized steelstandard length 3mfrom 250 mm pipes with external reinforcing embossmentindividual pipe lengths available upon requestindividual steel thickness available upon request
•••••
The pipes are manufactureed by modern machine made by SPIRO INTERNATIONAL SA
D(mm)
T(mm)
80 0,5
100 0,5
125 0,5
140 0,5
150 0,5
160 0,5
180 0,5
200 0,5
225 0,5
250 0,5
280 0,5
300 0,5
315 0,5
D(mm)
T(mm)
355 0,5
400 0,5
450 0,5
500 0,6
560 0,6
630 0,6
710 0,7
800 0,7
900 0,9
1000 0,9
1250 0,9
1600 1,2
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue 7
D(mm)
SPIRBOXPipe quantity (3m) in a cage
(pcs.)
SPIRBOX MIXAdditional diameter range
(mm)
100 200 80
125 130 80-100
160 80 80-150
200 48 80-180
250 30 80-224
315 20 -
SPIRBOX - SPIRO SAFE PIPE TRANSPORT SYSTEM
SPIRBOX RZ
SPIRBOX - it is a system of safe transport and mo-bile storage of spiral SPIRO pipes. Pipes are placed in specially designed for this purpose expandable cages. A cage full of pipes can be wholly loaded onto a car with a fork-lift truck and quickly unloaded in the same way. An empty cage can be disassembled, which simplifi es logistics in your company.
Round ducts
2460
1150
1550
1400
945
Centrum Klima – Products catalogue8
COIL PIPE (STAINLESS STEEL) RZN
Spiral pipes are made of stainless steel (1.4301 EN 10088-2) and their standard length is 3 m. Thickness of sheet: 0,5 mm.
DESCRIPTION
Product characteristics:stainless steelstandard length 3mindividual pipe lengths available upon requestindividual steel thickness available upon request
••••
D(mm)
T(mm)
L(m)
100 0,50 3
125 0,50 3
160 0,50 3
200 0,50 3
250 0,50 3
315 0,50 3
The pipes are manufactureed by modern machine made by SPIRO INTERNATIONAL SA
D
L
TT
Round ducts
m /h3[ [50
50
10
5
1
0,5
0,1
0,05
0,02100
100
200
500 1000 5000 10000
Wy datek powietrza
Stra
ta c
iś ni
enia
p
[Pa]
t
50000
[Pa/m]80
100
125
160
200
250
315
2
400
500
630
800
1000
5
10
1 5
20
V [m/s]
Śr. nominalna [mm]nominal diameter [mm]
air volume
pres
sure
loss
p, [
Pa]
Centrum Klima – Products catalogue 9
Round fi ttings
Size(mm)
D(mm)
A(mm)
H(mm)
Weight(kg)
80 78,9 72 40 0,27
100 98,9 90 40 0,35
125 123,9 112 40 0,52
150 148,9 135 40 0,71
160 158,9 144 40 0,83
180 178,9 160 40 1,03
200 198,9 180 40 1,27
250 248,9 225 50 2,30
PackagingItems (Set Package)
B9 B9X
P4 85 85
P2 110 110
P2 60 60
P1 75 75
P1 60 60
P1 45 45
P1 33 33
P1 18 16
90° BEND B9 / B9X
pressedfusion welded (linear weld)reinforced edges (fl anged)gasket (B9X) is positioned by fl anges
••••
PRODUCT CHARACTERISTICS
MATERIAL
galvanized steelEPDM (B9X) rubber gasket
••
Version with gasketB9X
A
H
D
90o
Version B9Z
Version B9MB
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue10
pressedfusion welded (linear weld)reinforced edges (fl anged)gasket (B6X) is positioned by fl anges
••••
MATERIAL PRODUCT CHARACTERISTICS
60° BEND B6 / B6X
galvanized steelEPDM (B6X) rubber gasket
••
Version with gasketB6X
60o
A
H
D
Size(mm)
D(mm)
A(mm)
H(mm)
Weight(kg)
80 78,9 72 40 0,30
100 98,9 90 40 0,40
125 123,9 112 40 0,50
150 148,9 135 40 0,90
160 158,9 144 40 1,00
180 178,9 160 40 1,20
200 198,9 180 40 1,50
Packaging Items B6/B6X(Set Package)
P6 80
P6 40
P6 22
P6 15
P4 20
P4 16
P4 12
Round fi ttings
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue 11
Round fi ttings
Size(mm)
D(mm)
A(mm)
H(mm)
Weight(kg)
80 78,9 72 40 0,19
100 98,9 90 40 0,24
125 123,9 112 40 0,34
150 148,9 135 40 0,44
160 158,9 144 40 0,52
180 178,9 160 40 0,62
200 198,9 180 40 0,77
250 248,9 225 50 1,30
Packaging Items(Set Package)
P6 90
P4 90
P2 100
P1 60
P1 110
P1 80
P1 55
P1 30
45° BEND B4 / B4X
pressedfusion welded (linear weld)reinforced edges (fl anged)gasket (B4X) is positioned by fl anges
••••
PRODUCT CHARACTERISTICS
MATERIAL
galvanized steelEPDM (B4X) rubber gasket
••
Version with gasketB4X
45o
A
H
D
Version B4Z
Version B4MB
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue12
pressedfusion welded (linear weld)reinforced edges (fl anged)gasket (B3X) is positioned by fl anges
••••
MATERIAL PRODUCT CHARACTERISTICS
30° BEND B3 / B3X
galvanized steelEPDM (B3X) rubber gasket
••
Version with gasketB3X
30 o
A
H
D
Size(mm)
D(mm)
A(mm)
H(mm)
Weight(kg)
80 78,9 72 40 0,20
100 98,9 90 40 0,30
125 123,9 112 40 0,30
150 148,9 135 40 0,40
160 158,9 144 40 0,50
180 178,9 160 40 0,60
200 198,9 180 40 0,70
Packaging Items B3/B3X(Set Package)
P12 55
P6 75
P6 40
P6 25
P6 20
P6 16
P4 18
Round fi ttings
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue 13
Round fi ttings
pressedfusion welded (linear weld)reinforced edges (fl anged)gasket (B1X) is positioned by fl anges
••••
PRODUCT CHARACTERISTICS
Size(mm)
D(mm)
A(mm)
H(mm)
Weight(kg)
80 78,9 72 40 0,20
100 98,9 90 40 0,30
125 123,9 112 40 0,30
150 148,9 135 40 0,40
160 158,9 144 40 0,50
180 178,9 160 40 0,60
200 198,9 180 40 0,60
Packaging Items B1/B1X(Set Package)
P12 70
P12 50
P12 28
P12 16
P12 15
P6 25
P6 16
MATERIAL
15° BEND B1 / B1X
galvanized steelrubber gasket EPDM (B1X)
••
Version with gasketB1X
15 o
A
H
D
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue14
segments connected with a lockfusion welded (linear weld)gasket (BSX) is positioned by fl anges
•••
MATERIAL PRODUCT CHARACTERISTICS
SECTIONAL BEND 90° 60° 45° 30° 15° BS / BSX
galvanized steelEPDM (BSX) rubber gasket
••
Version with gasketBSX
R=D
H
H
D
α= 15°, 30°, 45°, 60°, 90°
Round fi ttings
Size(mm)
90° 45° 30° 15°
Pack.(pc.)
ItemsSet
Package(pc.)
Pack.(pc.)
ItemsSet
Package(pc.)
Pack.(pc.)
ItemsSet
Package(pc.)
Pack.(pc.)
ItemsSet
Package(pc.)
225 21/P1 Z 36/P1 Z Z Z Z Z
250 16/P1 54 30/P1 96 40/P1 Z 25/P1 Z
280 Z Z 24/P1 Z Z Z Z Z
300 8/P1 28 16/P1 48 Z Z Z Z
315 8/P1 28 16/P1 48 Z Z Z Z
350 – Z Z Z Z Z Z Z
355 – 21 Z 42 Z Z Z Z
400 – 12 Z 30 Z Z Z Z
D(mm)
H(mm)
BS BSX
225 45 40
250 45 40
280 45 40
300 45 40
315 45 40
350 45 40
355 45 40
400 55 50
450 55 50
500 55 50
560 55 60
630 65 60
710 65 60
800 65 65
900 65 65
1000 65 65
Z - information upon request
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue 15
Round fi ttings
segments connected with a lockreinforced edges (fl anged)
••
PRODUCT CHARACTERISTICS
Dimension(mm)
D(mm)
H(mm)
100 98,9 40
125 123,9 40
160 158,9 40
200 198,9 40
250 248,5 45
315 313,4 45
MATERIAL
SEGMENTED BEND 90° 45° (STAINLESS STEEL) BSN
stainless steel, 1.4301 EN 10088-2 •
R=D
H
H
D
α= 45°, 90°
Centrum Klima – Products catalogue16
pressedsingle elementgasket (RCX) is positioned by fl anges
•••
PRODUCT CHARACTERISTICSMATERIAL
PRESSED REDUCER RC / RCX
galvanized steel EPDM (RCX) rubber gasket
••
Version with gasketRCX
45o
HL2
L
D
D1
Size(mm)
D(mm)
D1(mm)
L(mm)
L2(mm)
H(mm)
Weight(kg) Packaging
Items Set Package
RC RCX
100 80 98,8 78,8 110 55 40 0,11 P12 96 112
125 80 123,8 78,8 122 55 40 0,16 P12 63 63
125 100 123,8 98,8 112 55 45 0,18 P12 63 63
150 100 148,7 98,8 125 55 45 0,20 P12 42 42
150 125 148,7 123,8 122 55 45 0,20 P12 42 42
160 100 158,7 98,8 130 55 45 0,23 P12 35 35
160 125 158,7 123,8 117 55 45 0,21 P12 35 35
200 100 198,6 98,8 150 55 45 0,31 P12 28 28
200 125 198,6 123,8 137 55 45 0,30 P12 24 24
200 150 198,6 148,7 125 55 45 0,28 P12 28 28
200 160 198,6 158,7 120 55 45 0,29 P12 28 28
250 160 248,5 158,7 144 55 45 0,42 P4 30 30
250 200 248,5 198,6 125 55 45 0,38 P4 30 30
315 160 313,4 158,7 177 55 45 0,63 P4 16 16
315 200 313,4 198,6 157 55 45 0,59 P4 16 16
315 250 313,4 248,5 132 55 45 0,52 P4 16 16
355 250 353,4 248,5 200 45 45 1,16 P1 60 60
355 315 353,4 313,4 160 50 50 1,10 P1 66 66
Round fi ttings
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue 17
PRESSED REDUCER RCF/RFCX
pressedsingle elementfl anges are clamped on the gasket (RCFX)
•••
PRODUCT CHARACTERISTICSMATERIAL
galvanized steelEPDM (RCFX) rubber gasket
••
Version with gasketRCFX
45o
HL
D
D1
Size(mm)
D(mm)
D1(mm)
L(mm)
H(mm)
Weight(kg) Packaging
Items Set Package
RCF RCFX
100 80 100,5 78,8 110 40 0,11 P24 45 45
125 80 125,5 78,8 122 40 0,16 P12 72 72
125 100 125,5 98,8 112 45 0,16 P12 72 72
150 100 150,6 98,8 125 45 0,20 P12 48 48
150 125 150,6 123,8 122 45 0,19 P12 48 48
160 100 160,6 98,8 130 45 0,23 P12 35 60
160 125 160,6 123,8 117 45 0,21 P12 35 60
200 100 200,7 98,8 150 45 0,31 P12 28 52
200 125 200,7 123,8 137 45 0,30 P12 28 56
200 150 200,7 148,7 125 45 0,28 P12 28 60
200 160 200,7 158,7 120 45 0,29 P12 28 28
250 160 250,8 158,7 144 45 0,42 P4 30 30
250 200 250,8 198,6 125 45 0,38 P4 30 30
315 160 315,9 158,7 177 45 0,63 P4 18 18
315 200 315,9 198,6 157 45 0,59 P4 20 60
315 250 315,9 248,5 132 45 0,52 P4 18 18
Round fi ttings
Centrum Klima – Products catalogue18
B(mm)
D(mm)
L(mm)
RS RSX
X(mm)
Y(mm)
Items(Set
Package)Pack. X
(mm)Y
(mm)
Items(Set
Package)Pack.
125 80 60 37 40 Z Z 38 43 Z Z
125 100 60 37 40 Z Z 38 43 Z Z
140 80 60 37 40 Z Z 38 43 Z Z
140 100 60 37 40 Z Z 38 43 Z Z
140 125 60 37 40 Z Z 38 43 Z Z
150 80 60 37 40 75 P6 38 43 70 P6
150 100 60 37 40 Z Z 38 43 Z Z
150 125 60 37 40 Z Z 38 43 Z Z
150 140 60 37 40 Z Z 38 43 60 P4
160 80 60 37 40 Z Z 38 43 Z Z
160 100 60 37 40 Z Z 38 43 Z Z
160 125 60 37 40 Z Z 38 43 Z Z
160 140 60 37 40 Z Z 38 43 Z Z
160 150 60 37 40 Z Z 38 43 Z Z
180 80 80 37 40 50 P6 38 43 50 P6
180 100 60 37 40 Z Z 38 43 56 P6
segments are connected with a lockfusion welded (linear weld)gasket (RSX) is positioned by fl anges
•••
MATERIAL PRODUCT CHARACTERISTICS
SYMMETRIC SEGMENTED REDUCER RS / RSX
galvanized steelEPDM (RSX) rubber gasket
••
Version with gasketRSX
Round fi ttings
Part of class C air tightness certifi ced ventilation system.
RS
RSX
B(mm)
D(mm)
L(mm)
RS RSX
X(mm)
Y(mm)
Items(Set
Package)Pack. X
(mm)Y
(mm)
Items(Set
Package)Pack.
180 125 60 37 40 Z Z 38 43 Z Z
180 140 60 37 40 Z Z 38 43 Z Z
180 150 60 37 40 Z Z 38 43 Z Z
180 160 60 37 40 Z Z 38 43 Z Z
200 80 80 37 40 62 P4 38 43 45 P6
200 100 80 37 40 Z Z 38 43 Z Z
200 125 60 37 40 Z Z 38 43 Z Z
200 140 60 37 40 Z Z 38 43 Z Z
200 150 60 37 40 Z Z 38 43 Z Z
200 160 60 37 40 Z Z 38 43 Z Z
200 180 60 37 40 Z Z 38 43 Z Z
225 80 80 37 40 25 P4 38 43 25 P4
225 100 80 37 40 35 P4 38 43 35 P4
225 125 60 37 40 90 P2 38 43 28 P4
225 140 60 37 40 Z Z 38 43 Z Z
225 150 60 37 40 Z Z 38 43 Z Z
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue 19
B(mm)
D(mm)
L(mm)
RS RSX
X(mm)
Y(mm)
Items(Set
Package)Pack. X
(mm)Y
(mm)
Items(Set
Package)Pack.
225 160 60 37 40 Z Z 38 43 Z Z
225 180 60 37 40 Z Z 38 43 Z Z
225 200 60 37 40 Z Z 38 43 Z Z
250 80 80 37 40 25 P4 38 43 84 P2
250 100 80 37 40 35 P4 38 43 72 P2
250 125 80 37 40 Z Z 38 43 Z Z
250 140 80 37 40 Z Z 38 43 Z Z
250 150 80 37 40 80 P2 38 43 Z Z
250 160 80 37 40 Z Z 38 43 Z Z
250 180 60 37 40 Z Z 38 43 Z Z
250 200 60 37 40 Z Z 38 43 Z Z
250 225 60 37 40 Z Z 38 43 Z Z
280 80 100 37 40 Z Z 38 43 Z Z
280 100 100 37 40 Z Z 38 43 Z Z
280 125 100 37 40 Z Z 38 43 Z Z
280 140 80 37 40 Z Z 38 43 Z Z
280 150 80 37 40 Z Z 38 43 Z Z
280 160 80 37 40 Z Z 38 43 Z Z
280 180 80 37 40 Z Z 38 43 Z Z
280 200 60 37 40 Z Z 38 43 Z Z
280 225 60 37 40 Z Z 38 43 Z Z
280 250 60 37 40 Z Z 38 43 Z Z
300 80 100 37 40 45 P2 38 43 45 P2
300 100 100 37 40 80 P2 38 43 80 P2
300 125 100 37 40 45 P2 38 43 45 P2
300 140 100 37 40 Z Z 38 43 Z Z
300 150 80 37 40 50 P2 38 43 50 P2
300 160 80 37 40 44 P2 38 43 44 P2
300 180 80 37 40 Z Z 38 43 Z Z
300 200 60 37 40 50 P2 38 43 Z Z
300 225 60 37 40 50 P2 38 43 50 P2
300 250 60 37 40 48 P2 38 43 48 P2
300 280 60 37 40 Z Z 38 43 Z Z
315 80 100 37 36 45 P2 38 43 45 P2
315 100 100 37 36 45 P2 38 43 80 P2
315 125 100 37 36 45 P2 38 43 45 P2
315 140 100 37 36 Z Z 38 43 Z Z
315 150 100 37 36 50 P2 38 43 50 P2
315 160 100 37 36 Z Z 38 43 Z Z
315 180 80 37 36 Z Z 38 43 Z Z
315 200 80 37 36 Z Z 38 43 Z Z
315 225 60 37 36 55 P2 38 43 55 P2
315 250 60 37 36 Z Z 38 43 Z Z
315 280 60 37 36 Z Z 38 43 Z Z
315 300 60 37 36 56 P2 38 43 48 P2
355 150 100 37 36 50 P1 38 43 50 P1
Round fi ttings
B(mm)
D(mm)
L(mm)
RS RSX
X(mm)
Y(mm)
Items(Set
Package)Pack. X
(mm)Y
(mm)
Items(Set
Package)Pack.
355 160 100 37 36 Z Z 38 43 Z Z
355 180 80 37 36 Z Z 38 43 Z Z
355 200 80 37 36 60 P1 38 43 60 P1
355 225 80 37 36 Z Z 38 43 Z Z
355 250 80 37 36 60 P1 38 43 60 P1
355 280 60 37 36 Z Z 38 43 Z Z
355 300 60 37 36 66 P1 38 43 66 P1
355 315 60 37 36 66 P1 38 43 66 P1
400 160 100 37 36 Z Z 38 50 Z Z
400 180 100 37 36 Z Z 38 50 Z Z
400 200 100 37 36 60 P1 38 50 60 P1
400 225 100 37 36 Z Z 38 50 Z Z
400 250 100 37 36 60 P1 38 50 55 P1
400 280 80 37 36 Z Z 38 50 Z Z
400 300 80 37 36 60 P1 38 50 60 P1
400 315 70 37 36 30 P2 38 50 28 P2
400 355 60 37 36 60 P1 38 50 55 P1
450 160 100 37 36 Z Z 38 50 Z Z
450 180 100 37 36 Z Z 38 50 Z Z
450 200 100 37 36 45 P1 38 50 38 P1
450 225 100 37 36 Z Z 38 50 Z Z
450 250 100 37 36 45 P1 38 50 38 P1
450 280 100 37 36 Z Z 38 50 Z Z
450 300 100 37 36 45 P1 38 50 45 P1
450 315 100 37 36 45 P1 38 50 38 P1
450 355 80 37 36 45 P1 38 50 38 P1
450 400 60 37 36 45 P1 45 50 38 P1
500 160 150 37 36 Z Z 38 50 Z Z
500 180 150 37 36 Z Z 38 50 Z Z
500 200 150 37 36 40 P1 38 50 40 P1
500 225 100 37 36 Z Z 38 50 Z Z
500 250 100 37 36 40 P1 38 50 40 P1
500 280 100 37 36 Z Z 38 50 Z Z
500 300 100 37 36 40 P1 38 50 40 P1
500 315 100 37 36 20 P1 38 50 16 P2
500 355 100 37 36 20 P1 38 50 16 P2
500 400 80 37 36 20 P2 45 50 16 P2
500 450 60 37 36 40 P1 45 50 32 P1
560 160 150 37 46 Z Z 38 50 Z Z
560 180 150 37 46 Z Z 38 50 Z Z
560 200 150 37 46 Z Z 38 50 Z Z
560 225 100 37 46 Z Z 38 50 Z Z
560 250 100 37 46 Z Z 38 50 Z Z
560 280 100 37 46 Z Z 38 50 Z Z
560 300 100 37 46 Z Z 38 50 Z Z
560 315 100 37 46 Z Z 38 50 Z Z
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue20
Round fi ttings
B(mm)
D(mm)
L(mm)
RS RSX
X(mm)
Y(mm)
Items(Set
Package)Pack. X
(mm)Y
(mm)
Items(Set
Package)Pack.
560 355 100 37 46 Z Z 38 50 Z Z
560 400 100 37 46 Z Z 45 50 Z Z
560 450 80 37 46 Z Z 45 50 Z Z
560 500 60 37 46 Z Z 45 50 Z Z
600 400 100 37 46 Z Z 45 50 Z Z
600 450 100 37 46 Z Z 45 50 Z Z
600 500 80 37 46 Z Z 45 50 Z Z
600 560 60 47 46 Z Z 45 50 Z Z
630 180 150 37 46 Z Z 38 50 Z Z
630 200 150 37 46 Z Z 38 50 Z Z
630 225 150 37 46 Z Z 38 50 Z Z
630 250 150 37 46 20 P1 38 50 20 P1
630 280 150 37 46 Z Z 38 50 Z Z
630 300 150 37 46 Z Z 38 50 Z Z
630 315 150 37 46 Z Z 38 50 Z Z
630 355 150 37 46 Z Z 38 50 Z Z
630 400 100 37 46 Z Z 45 50 Z Z
630 450 100 37 46 Z Z 45 50 Z Z
630 500 100 37 46 Z Z 45 50 Z Z
630 560 80 47 46 Z Z 45 50 Z Z
710 355 150 37 60 Z Z 38 68 Z Z
710 400 100 37 60 Z Z 45 68 Z Z
710 450 100 37 60 Z Z 45 68 Z Z
710 500 100 37 60 Z Z 45 68 Z Z
710 560 100 47 60 Z Z 45 68 Z Z
710 600 100 47 60 Z Z 45 68 Z Z
710 630 100 47 60 Z Z 63 68 Z Z
800 355 180 37 60 Z Z 38 78 Z Z
800 400 150 37 60 Z Z 45 78 Z Z
800 450 150 37 60 Z Z 45 78 Z Z
800 500 100 37 60 Z Z 45 78 Z Z
800 560 100 47 60 Z Z 45 78 Z Z
800 600 80 47 60 Z Z 45 78 Z Z
800 630 80 47 60 Z Z 63 78 Z Z
800 710 80 55 60 Z Z 63 78 Z Z
900 500 150 37 65 Z Z 45 78 Z Z
900 560 150 47 65 Z Z 45 78 Z Z
900 600 100 47 65 Z Z 45 78 Z Z
900 630 80 47 65 Z Z 63 78 Z Z
900 710 80 55 65 Z Z 63 78 Z Z
900 800 80 55 65 Z Z 73 78 Z Z
1000 630 150 47 65 Z Z 63 93 Z Z
1000 710 100 55 65 Z Z 63 93 Z Z
1000 800 100 55 65 Z Z 73 93 Z Z
1000 900 80 65 65 Z Z 73 93 Z Z
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue 21
segments are connected with a lockfusion welded (linear weld)
••
PRODUCT CHARACTERISTICSMATERIAL
SYMMETRICAL REDUCERS (STAINLESS STEEL) RSN
stainless steel, 1.4301 EN 10088-2•
RSN
B(mm)
D(mm)
L(mm)
X=Y(mm)
Items(Set Package) Packaging
125 100 60 40 Z Z
160 125 60 40 Z Z
200 160 60 40 Z Z
250 200 60 40 Z Z
315 250 60 40 Z Z
L XY
B D
Round fi ttings
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue22
segments are connected with a lockfusion welded (linear weld)gasket (RNX) is positioned by fl anges
•••
PRODUCT CHARACTERISTICSMATERIAL
ASYMMETRICAL SEGMENTED REDUCER RN / RNX
galvanized steel EPDM (RNX) rubber gasket
••
Version with gasketRNX
L XY
B
D
B (mm)
D (mm)
L (mm)
X=Y (mm)
125 100 100 40
160 100 100 40
160 125 100 40
200 100 100 40
200 125 100 40
200 160 100 40
250 100 150 40
250 125 150 40
250 160 100 40
250 200 100 40
315 100 200 40
315 125 200 40
315 160 150 40
315 200 150 40
B (mm)
D (mm)
L (mm)
X=Y (mm)
315 250 150 40
315 300 150 40
400 160 200 40
400 200 200 40
400 250 150 40
400 315 100 40
450 200 200 40
450 250 200 45
450 300 150 45
450 315 100 45
450 355 100 45
450 400 100 45
500 200 200 45
500 250 200 45
B (mm)
D (mm)
L (mm)
X=Y (mm)
500 315 200 45
500 400 100 45
500 450 100 45
630 315 200 50
630 400 200 50
630 450 200 50
630 500 100 50
800 350 200 50
800 400 200 50
800 450 200 50
800 500 200 50
800 630 200 50
1000 630 200 50
1000 800 200 50
Round fi ttings
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue 23
D(mm)
B(mm)
TS TSX
X(mm)
Y(mm)
L(mm)
h1(mm)
Items(Set Package) Pack. X
(mm)Y
(mm)L
(mm)h1
(mm)Items
(Set Package) Pack.
80 80 30 30 140 56 160 P2 40 40 200 56 160 P2
100 80 30 30 140 66 108 P2 40 40 200 66 108 P2
100 100 30 30 170 68 94 P2 40 40 220 68 60 P2
125 80 35 30 130 79 85 P2 40 40 200 79 85 P2
125 100 35 30 160 81 60 P2 40 40 220 81 50 P2
125 125 35 35 180 81 60 P2 40 40 241 81 44 P2
140 80 35 30 130 86 62 P2 40 40 200 86 56 P2
140 100 35 30 160 88 46 P2 40 40 217 88 42 P2
140 125 35 35 180 88 45 P2 40 40 245 88 41 P2
150 80 35 30 130 91 58 P2 40 40 200 91 52 P2
150 100 35 30 160 93 42 P2 40 40 220 93 39 P2
150 125 35 35 180 93 39 P2 40 40 245 93 39 P2
150 150 35 35 220 97 33 P2 40 40 270 97 28 P2
160 80 35 30 130 96 58 P2 40 40 116 96 58 P2
160 100 35 30 160 98 42 P2 40 40 150 98 42 P2
160 125 35 35 180 98 39 P2 40 40 245 98 25 P2
SYMMETRICAL TEE WITH PRESSED FITTED CONNECTION TS / TSX
the outgoing connection is made of PS branchingfusion welded (linear weld)the outgoing connection is fi tted with bossingsgasket (TSX) is positioned by fl anges
••••
MATERIAL PRODUCT CHARACTERISTICS
galvanized steel EPDM (TSX) rubber gasket
••
Version with gasketTSX
Notice: actual D and B size are 2 mm smaller Z - information upon request
Round fi ttings
Part of class C air tightness certifi ced ventilation system.
TS
TSX
Centrum Klima – Products catalogue24
Round fi ttings
D(mm)
B(mm)
TS TSX
X(mm)
Y(mm)
L(mm)
h1(mm)
Items(Set Package) Pack. X
(mm)Y
(mm)L
(mm)h1
(mm)Items
(Set Package) Pack.
160 150 35 35 220 102 33 P2 40 40 270 102 27 P2
160 160 35 35 230 102 28 P2 40 40 280 102 20 P2
180 80 40 30 120 106 160 P1 40 40 116 106 42 P2
180 100 40 30 150 108 30 P2 40 40 146 108 30 P2
180 125 40 35 170 108 30 P2 40 40 245 108 21 P2
180 150 40 35 210 112 29 P2 40 40 270 112 27 P1
180 160 40 35 220 112 20 P2 40 40 276 112 17 P2
200 80 40 30 120 116 38 P2 40 40 116 116 38 P2
200 100 40 30 150 118 27 P2 40 40 150 118 27 P2
200 125 40 35 170 118 27 P2 40 40 171 118 27 P2
200 150 40 35 220 122 29 P1 40 40 270 122 26 P1
200 160 40 35 220 122 16 P2 40 40 281 122 15 P2
200 200 40 40 280 126 32 P1 40 40 320 126 25 P1
225 80 40 30 130 129 52 P1 40 40 126 129 52 P1
225 100 40 30 150 131 20 P2 40 40 146 131 20 P2
225 125 40 35 170 131 40 P1 40 40 176 131 40 P1
225 150 40 35 210 135 24 P1 40 40 270 135 22 P1
225 160 40 35 220 135 26 P1 40 40 280 135 24 P1
225 200 40 40 280 139 26 P1 40 40 320 139 23 P1
250 80 40 30 130 141 52 P1 40 40 126 141 52 P1
250 100 40 30 150 143 39 P1 40 40 150 143 39 P1
250 125 40 35 170 143 39 P1 40 40 174 143 39 P1
250 150 40 35 220 147 24 P1 40 40 206 147 22 P1
250 160 40 35 220 147 24 P1 40 40 216 147 22 P1
250 200 40 40 280 151 22 P1 40 40 320 151 20 P1
250 250 40 40 340 151 18 P1 40 40 370 151 18 P1
280 80 40 30 130 156 30 P1 40 40 126 156 30 P1
280 100 40 30 150 158 39 P1 40 40 146 158 30 P1
280 125 40 35 170 158 30 P1 40 40 186 158 30 P1
280 150 40 35 210 162 18 P1 40 40 206 162 18 P1
280 160 40 35 230 162 19 P1 40 40 216 162 19 P1
280 200 40 40 280 166 17 P1 40 40 320 166 17 P1
280 250 40 40 330 166 14 P1 40 40 370 166 14 P1
300 80 40 30 130 166 21 P1 40 40 126 166 21 P1
300 100 40 30 150 168 24 P1 40 40 156 168 24 P1
300 125 40 35 170 168 21 P1 40 40 186 168 21 P1
300 150 40 35 210 172 16 P1 40 40 216 172 14 P1
300 160 40 35 220 172 16 P1 40 40 216 172 16 P1
300 200 40 40 280 176 14 P1 40 40 276 176 14 P1
300 250 40 40 340 176 12 P1 40 40 370 176 12 P1
315 80 40 30 130 174 21 P1 40 40 126 174 21 P1
315 100 40 30 150 176 24 P1 40 40 150 176 24 P1
315 125 40 35 170 176 21 P1 40 40 186 176 21 P1
315 150 40 35 220 180 14 P1 14 P1
315 160 40 35 220 180 16 P1 40 40 216 180 16 P1
315 200 40 40 280 184 14 P1 40 40 276 184 14 P1
315 250 40 40 340 184 12 P1 40 40 370 184 12 P1
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue 25
Round fi ttings
D(mm)
B(mm)
TS TSX
X(mm)
Y(mm)
L(mm)
h1(mm)
Items(Set Package) Pack. X
(mm)Y
(mm)L
(mm)h1
(mm)Items
(Set Package) Pack.
315 300 40 40 340 184 9 P1 9 P1
315 315 40 40 420 189 9 P1 40 40 436 189 8 P1
400 100 40 30 150 218 Z Z 50 40 161 218 Z Z
400 150 40 35 210 222 Z Z
400 160 40 35 220 222 Z Z 50 40 206 222 Z Z
400 200 40 40 280 226 Z Z 50 40 266 226 Z Z
400 250 40 40 340 226 Z Z 50 40 306 226 Z Z
400 315 40 40 420 231 Z Z 50 40 389 231 Z Z
450 100 50 30 160 243 Z Z 50 40 156 243 Z Z
450 125 50 40 166 243 Z Z
450 160 50 40 216 247 Z Z
500 100 50 30 160 268 Z Z 50 40 156 268 Z Z
500 125 50 35 185 268 Z Z 50 40 181 268 Z Z
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue26
Round fi ttings
SYMMETRICAL TEE WITH WELD FITTED CONNECTION TS / TSX
the outgoing connection is made of PS branchingfusion welded (linear weld)the outgoing connection is fi tted with bossingsgasket (TSX) is positioned by fl anges
••••
MATERIAL PRODUCT CHARACTERISTICS
galvanized steel EPDM (TSX) rubber gasket
••
Version with gasketTSX
Part of class C air tightness certifi ced ventilation system.
TS
TSX
D(mm)
B(mm)
TS TSX
X(mm)
Y(mm)
L(mm)
h1(mm)
Items(Set Package) Pack. X
(mm)Y
(mm)L
(mm)h1
(mm)Items
(Set Package) Pack.
140 140 35 35 190 95 33 P2 40 40 176 88 33 P2
150 100 35 30 150 105 42 P2
150 140 35 35 190 100 33 P2 40 40 176 93 39 P2
150 150 35 35 200 100 33 P2
160 140 35 35 190 105 33 P2 40 40 176 98 33 P2
180 140 40 35 180 115 29 P2 40 40 176 108 30 P2
180 180 40 40 220 115 35 P1 40 40 216 108 36 P1
200 140 40 35 180 125 29 P1 40 40 176 118 27 P2
200 180 40 40 216 118 34 P1
200 200 40 40 220 125 32 P1
225 140 40 35 190 138 26 P1 40 40 176 131 21 P2
225 180 40 40 230 138 25 P1 40 40 261 131 25 P1
225 200 40 40 250 138 26 P1
225 225 40 40 275 138 22 P1 40 40 261 131 22 P1
250 140 40 35 190 150 24 P1 40 40 181 143 24 P1
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue 27
Round fi ttings
D(mm)
B(mm)
TS TSX
X(mm)
Y(mm)
L(mm)
h1(mm)
Items(Set Package) Pack. X
(mm)Y
(mm)L
(mm)h1
(mm)Items
(Set Package) Pack.
250 150 40 35 220 150 24 P1
250 180 40 40 230 150 22 P1 40 40 216 143 22 P1
250 225 40 40 275 150 18 P1 40 40 256 143 18 P1
250 250 40 40 340 150 18 P1 40 40 370 148 18 P1
280 140 40 35 190 165 18 P1 40 40 176 158 18 P1
280 180 40 40 230 165 17 P1 40 40 216 158 18 P1
280 200 40 40 320 158 17 P1
280 225 40 40 275 165 14 P1 40 40 261 158 14 P1
280 250 40 40 330 165 14 P1
280 280 40 40 330 165 10 P1 40 40 316 163 14 P1
300 100 40 30 150 180 24 P1
300 140 40 35 190 175 16 P1 40 40 176 168 14 P1
300 180 40 40 230 175 14 P1 40 40 216 168 16 P1
300 225 40 40 275 175 12 P1 40 40 261 168 12 P1
300 280 40 40 330 175 10 P1 40 40 316 173 9 P1
300 300 40 40 380 175 10 P1 40 40 366 173 10 P1
315 140 40 35 190 183 14 P1 40 40 176 176 14 P1
315 180 40 40 230 183 21 P1
315 225 40 40 275 183 12 P1 40 40 261 176 12 P1
315 250 40 40 340 183 12 P1 40 40 370 181 12 P1
315 280 40 40 330 183 10 P1 40 40 316 181 10 P1
315 315 40 40 420 183 9 P1 40 40 436 181 8 P1
355 100 40 30 150 208 Z Z 40 40 136 196 Z Z
355 125 40 35 175 203 Z Z 40 40 161 196 Z Z
355 140 40 40 190 203 Z Z 40 40 176 196 Z Z
355 150 40 40 200 203 Z Z 40 40 186 196 Z Z
355 160 40 40 210 203 Z Z 40 40 196 196 Z Z
355 180 40 40 230 203 Z Z 40 40 216 196 Z Z
355 200 40 40 250 203 Z Z
355 225 40 40 275 203 12 P1 40 40 261 196 12 P1
355 250 40 40 300 203 Z Z 40 40 286 201 12 P1
355 280 40 40 330 203 Z Z 40 40 316 201 Z Z
355 300 40 40 350 203 Z Z 40 40 336 201 Z Z
355 315 40 40 365 203 Z Z 40 40 356 201 Z Z
355 355 40 40 405 203 Z Z 40 40 391 201 8 P1
400 125 40 35 175 225 Z Z 50 40 161 218 Z Z
400 140 40 35 190 225 Z Z 50 40 176 218 Z Z
400 150 40 35 200 225 Z Z 50 40 186 218 Z Z
400 160 40 35 210 225 Z Z
400 180 40 40 230 225 Z Z 50 40 216 218 Z Z
400 200 40 40 280 225 Z Z 50 40 266 218 Z Z
400 225 40 40 275 225 Z Z 50 40 261 218 Z Z
400 250 40 40 340 225 Z Z 50 40 306 223 Z Z
400 280 40 40 330 225 Z Z 50 40 316 223 Z Z
400 300 40 40 350 225 Z Z 50 40 336 223 Z Z
400 315 40 40 420 225 Z Z 50 40 386 223 Z Z
400 355 40 40 405 225 Z Z 50 40 391 223 Z Z
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue28
D(mm)
B(mm)
TS TSX
X(mm)
Y(mm)
L(mm)
h1(mm)
Items(Set Package) Pack. X
(mm)Y
(mm)L
(mm)h1
(mm)Items
(Set Package) Pack.
400 400 40 40 450 225 Z Z 50 50 436 223 Z Z
450 125 50 35 175 250 Z Z 50 40 166 243 Z Z
450 140 50 35 190 250 Z Z 50 40 176 243 Z Z
450 150 50 40 186 243 Z Z
450 180 50 40 230 250 Z Z 50 40 216 243 Z Z
450 200 50 40 250 250 Z Z 50 40 236 243 Z Z
450 225 50 40 275 250 Z Z 50 40 261 243 Z Z
450 250 50 40 300 250 Z Z 50 40 286 248 Z Z
450 280 50 40 330 250 Z Z 50 40 316 248 Z Z
450 300 50 40 350 250 Z Z 50 40 336 248 Z Z
450 315 50 40 365 250 Z Z 50 40 351 248 Z Z
450 355 50 40 405 250 Z Z 50 40 391 248 Z Z
450 400 50 40 450 250 Z Z 50 50 436 248 Z Z
450 450 50 50 500 255 Z Z 50 50 486 248 Z Z
500 140 50 35 190 275 Z Z 50 40 176 268 Z Z
500 150 50 40 186 268 Z Z
500 160 50 35 210 275 Z Z 50 40 196 268 Z Z
500 180 50 40 230 275 Z Z 50 40 216 268 Z Z
500 200 50 40 250 275 Z Z 50 40 236 268 Z Z
500 225 50 40 275 275 Z Z 50 40 261 268 Z Z
500 250 50 40 300 275 Z Z 50 40 286 273 Z Z
500 280 50 40 330 275 Z Z 50 40 316 273 Z Z
500 300 50 40 350 275 Z Z 50 40 336 273 Z Z
500 315 50 40 365 275 Z Z 50 40 351 273 Z Z
500 355 50 40 405 275 Z Z 50 40 391 273 Z Z
500 400 50 40 450 275 Z Z 50 50 436 273 Z Z
500 450 50 50 500 280 Z Z 50 50 486 273 Z Z
500 500 50 50 550 280 Z Z 50 50 536 273 Z Z
560 200 60 40 250 305 Z Z 60 40 246 298 Z Z
560 315 60 40 365 305 Z Z 60 40 361 303 Z Z
560 400 60 40 450 305 Z Z 60 50 446 303 Z Z
560 450 60 50 500 310 Z Z 60 50 496 303 Z Z
560 500 60 50 550 310 Z Z 60 50 546 303 Z Z
560 560 60 60 610 310 Z Z 60 60 606 308 Z Z
630 100 60 30 150 345 Z Z 60 40 146 333 Z Z
630 125 60 35 175 340 Z Z 60 40 171 333 Z Z
630 140 60 35 190 340 Z Z 60 40 186 333 Z Z
630 150 60 35 200 340 Z Z 60 40 196 333 Z Z
630 160 60 35 210 340 Z Z 60 40 206 333 Z Z
630 180 60 40 230 340 Z Z 60 40 226 333 Z Z
630 200 60 40 250 340 Z Z 60 40 246 333 Z Z
630 225 60 40 275 340 Z Z 60 40 271 333 Z Z
630 250 60 40 300 340 Z Z 60 40 296 338 Z Z
630 280 60 40 330 340 Z Z 60 40 326 338 Z Z
630 300 60 40 350 340 Z Z 60 40 346 338 Z Z
630 315 60 40 365 340 Z Z 60 40 361 338 Z Z
630 355 60 40 405 340 Z Z 60 40 401 338 Z Z
Round fi ttings
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue 29
D(mm)
B(mm)
TS TSX
X(mm)
Y(mm)
L(mm)
h1(mm)
Items(Set Package) Pack. X
(mm)Y
(mm)L
(mm)h1
(mm)Items
(Set Package) Pack.
630 400 60 40 450 340 Z Z 60 50 446 338 Z Z
630 450 60 50 500 345 Z Z 60 50 496 338 Z Z
630 500 60 50 550 345 Z Z 60 50 546 338 Z Z
630 560 60 60 610 345 Z Z 60 60 606 343 Z Z
630 630 60 60 680 345 Z Z 60 60 676 343 Z Z
710 315 60 40 365 380 Z Z 60 40 361 378 Z Z
710 400 60 40 450 380 Z Z 60 50 446 378 Z Z
710 500 60 50 550 385 Z Z 60 50 546 378 Z Z
710 630 60 60 680 385 Z Z 60 60 676 383 Z Z
710 710 60 60 760 385 Z Z 60 60 756 383 Z Z
800 315 65 40 365 425 Z Z 65 40 361 423 Z Z
800 400 65 40 450 425 Z Z 65 50 446 423 Z Z
800 450 65 50 500 430 Z Z 65 50 496 423 Z Z
800 500 65 50 546 423 Z Z
800 630 65 60 680 430 Z Z 65 60 676 428 Z Z
800 710 65 60 760 430 Z Z 65 60 756 428 Z Z
800 800 65 65 850 430 Z Z 65 65 846 428 Z Z
Round fi ttings
Notice: actual D and B size are 2 mm smaller Z - information upon request
Centrum Klima – Products catalogue30
Round fi ttings
SYMMETRICAL TEE TSHF/TSHFX
outlet made of entirely pressed upper partsmaller losses of pressuredoes not require silicone gasketsaesthetic looks
••••
MATERIAL PRODUCT CHARACTERISTICS
galvanized steelEPDM (TSHFX) rubber gasket
••
Version with gasketTSHFX
h1
D
LX
B
Y
TSHF
TSHFX
h1
D
LX
B
Y
TSHF/TSHFX
D (mm)
B (mm)
L (mm)
X (mm)
Y (mm)
h1(mm)
Items Set Package Packaging
100 80 85 40 40 62 72 P4
100 100 117 40 40 65 107 P2
125 80 85 40 40 75 96 P2
125 100 117 40 40 78 75 P2
125 125 152 40 40 86 60 P2
160 100 117 40 40 95 52 P2
160 125 152 40 40 103 39 P2
160 160 197 40 40 108 30 P2
200 160 197 40 40 128 24 P2
200 200 237 40 40 128 36 P1
250 250 327 40 40 173 18 P1
315 315 392 40 40 206 10 P1
Centrum Klima – Products catalogue 31
MATERIAL
SYMMETRICAL TEE (STAINLESS STEEL) TSN
stainless steel, 1.4301 EN 10088-2•
TSN
D(mm)
B(mm)
L(mm)
X=Y(mm)
Items Set Package Packaging
100 100 150 30 94 P2
125 100 150 30 60 P2
125 125 170 30 60 P2
160 125 170 30 39 P2
160 160 220 40 28 P2
200 160 220 40 16 P2
200 200 280 40 32 P1
250 200 280 40 22 P1
250 250 350 40 18 P1
315 250 350 40 12 P1
315 315 415 40 9 P1
D
LX
B
Y
Notice: actual D and B size are 2 mm smaller
fusion welded (linear weld)the outgoing connection is fi tted with bossings
••
PRODUCT CHARACTERISTICS
Round fi ttings
Centrum Klima – Products catalogue32
pressedsingle element
••
MATERIAL
PRODUCT CHARACTERISTICS
COLAR SADDLE PS / PSX
galvanized steelEPDM (PSX) rubber gasket
••
Version with gasketPSX
Size(mm)
D1(mm)
D(mm)
H(mm)
B(mm)
R(mm)
Weight(kg) Packaging Items
Set PackageWeight
(kg/package)
80 80 78,8 80 40 30 10 0,10 P24 30 7
100 80 78,8 100 40 30 10 0,10 P12 60 7
125 80 78,8 125 40 30 10 0,10 P12 60 7
150 80 78,8 160 40 30 10 0,09 P12 60 7
160 80 78,8 160 40 30 10 0,09 P12 70 7
180 80 78,8 200 40 30 10 0,09 P12 70 7
200 80 78,8 200 40 30 10 0,09 P12 70 7
225 80 78,8 200 40 30 10 0,09 P12 70 7
250 80 78,8 250 40 30 10 0,09 P24 34 7
280 80 78,8 250 40 30 10 0,09 P12 60 7
300 80 78,8 250 40 30 10 0,09 P12 60 7
315 80 78,8 315 40 30 10 0,09 P12 60 7
355 80 78,8 355 40 30 10 0,09 P12 60 7
400 80 78,8 400 40 30 10 0,09 P12 60 7
D1
B
H
R
D
Round fi ttings
Centrum Klima – Products catalogue 33
Round fi ttings
Size(mm)
D1(mm)
D(mm)
H(mm)
B(mm)
R(mm)
Weight(kg) Packaging Items
Set PackageWeight
(kg/package)
100 100 98,8 100 40 32 12 0,14 P6 75 12
125 100 98,8 125 40 32 12 0,13 P6 80 12
150 100 98,8 160 40 32 12 0,12 P6 90 12
160 100 98,8 160 40 32 12 0,12 P6 90 12
180 100 98,8 200 40 32 12 0,12 P6 90 13
200 100 98,8 200 40 32 12 0,12 P6 90 13
225 100 98,8 200 40 32 12 0,12 P6 100 13
250 100 98,8 250 40 32 12 0,12 P6 90 13
280 100 98,8 250 40 32 12 0,12 P6 100 13
300 100 98,8 315 40 32 12 0,12 P6 100 13
315 100 98,8 315 40 32 12 0,12 P6 100 13
355 100 98,8 315 40 32 12 0,12 P6 100 13
400 100 98,8 400 40 32 12 0,12 P6 100 13
450 100 98,8 450 40 32 12 0,12 P6 100 13
500 100 98,8 500 40 32 12 0,12 P6 100 13
560 100 98,8 500 40 32 12 0,12 P6 100 13
600 100 98,8 500 40 32 12 0,12 P6 100 13
630 100 98,8 500 40 32 12 0,12 P6 100 13
710 100 98,8 710 40 32 12 0,12 P6 100 13
800 100 98,8 800 40 32 12 0,12 P6 100 13
125 125 123,8 125 40 32 12 0,21 P6 40 15
150 125 123,8 160 40 32 12 0,19 P4 65 14
160 125 123,8 160 40 32 12 0,19 P6 50 14
180 125 123,8 200 40 32 12 0,17 P4 75 14
200 125 123,8 200 40 32 12 0,17 P6 52 14
225 125 123,8 250 40 32 12 0,17 P4 75 14
250 125 123,8 250 40 32 12 0,17 P6 50 14
280 125 123,8 250 40 32 12 0,17 P4 75 14
300 125 123,8 315 40 32 12 0,17 P4 80 15
315 125 123,8 315 40 32 12 0,17 P6 54 15
355 125 123,8 315 40 32 12 0,17 P4 80 15
400 125 123,8 315 40 32 12 0,17 P4 80 15
450 125 123,8 500 40 32 12 0,15 P4 100 16
500 125 123,8 500 40 32 12 0,15 P4 100 16
560 125 123,8 500 40 32 12 0,15 P4 100 16
600 125 123,8 500 40 32 12 0,15 P4 100 16
630 125 123,8 500 40 32 12 0,15 P4 100 16
150 150 148,7 150 40 36 16 0,31 P6 25 13
160 150 148,7 150 40 36 16 0,31 P4 36 13
180 150 148,7 200 40 36 16 0,27 P4 72 21
200 150 148,7 200 40 36 16 0,27 P6 30 21
225 150 148,7 250 40 36 16 0,26 P4 72 20
250 150 148,7 250 40 36 16 0,26 P6 35 20
280 150 148,7 315 40 36 16 0,26 P4 72 20
300 150 148,7 315 40 36 16 0,26 P4 72 20
315 150 148,7 315 40 36 16 0,26 P6 35 20
355 150 148,7 315 40 36 16 0,26 P4 72 20
Centrum Klima – Products catalogue34
Size(mm)
D1(mm)
D(mm)
H(mm)
B(mm)
R(mm)
Weight(kg) Packaging Items
Set PackageWeight
(kg/package)
160 160 158,7 160 40 36 16 0,34 P6 20 24
180 160 158,7 200 40 36 16 0,29 P4 63 20
200 160 158,7 200 40 36 16 0,29 P6 25 20
225 160 158,7 250 40 36 16 0,29 P4 62 18
250 160 158,7 250 40 36 16 0,29 P6 25 18
280 160 158,7 315 40 36 16 0,27 P4 66 19
300 160 158,7 315 40 36 16 0,27 P4 66 19
315 160 158,7 315 40 36 16 0,27 P6 25 19
355 160 158,7 400 40 36 16 0,25 P4 66 18
400 160 158,7 400 40 36 16 0,25 P6 30 18
450 160 158,7 450 40 36 16 0,25 P4 66 18
500 160 158,7 500 40 36 16 0,25 P6 30 18
200 200 198,6 200 40 50 20 0,46 P4 32 39
225 200 198,6 250 40 50 20 0,41 P4 32 15
250 200 198,6 250 40 50 20 0,41 P4 32 15
280 200 198,6 315 40 50 20 0,41 P4 32 15
300 200 198,6 315 40 50 20 0,41 P4 32 15
315 200 198,6 315 40 50 20 0,41 P4 32 15
355 200 198,6 400 40 50 20 0,37 P4 38 15
400 200 198,6 400 40 50 20 0,37 P4 42 15
450 200 198,6 450 40 50 20 0,37 P4 38 15
250 250 248,5 250 40 50 20 0,63 P4 15 35
280 250 248,5 315 40 50 20 0,50 P2 55 30
300 250 248,5 315 40 50 20 0,50 P2 55 30
315 250 248,5 315 40 50 20 0,50 P4 15 30
355 250 248,5 400 40 50 20 0,49 P2 56 30
400 250 248,5 400 40 50 20 0,49 P4 18 30
315 315 313,4 315 40 55 25 0,85 P1 42 68
400 315 313,4 400 40 55 25 0,68 P1 40 52
Round fi ttings
Centrum Klima – Products catalogue 35
Round fi ttings
45° BRANCHING FOR ROUND DUCTS PS4/PS4X
DiameterØ (mm)
PS4 PS4X
L [mm] Z [mm] L [mm] Z [mm]
80 70 40 68 40
100 70 40 68 40
125 70 40 68 40
140 70 40 68 40
150 70 40 68 40
160 70 40 68 40
180 70 40 68 40
200 70 40 68 40
225 70 40 68 40
250 70 40 68 40
280 70 40 68 40
300 70 40 68 40
L
Z
Ø
pressedsingle element
••
PRODUCT CHARACTERISTICS
MATERIAL
galvanized steel EPDM (PS4X) rubber gasket
••
Version with gasketPS4X
DiameterØ (mm)
PS4 PS4X
L [mm] Z [mm] L [mm] Z [mm]
315 70 40 68 40
355 70 40 68 40
400 70 40 90 50
450 90 50 90 50
500 90 50 90 50
560 90 60 90 60
600 90 60 90 60
630 90 60 90 60
710 110 60 110 60
800 110 65 110 65
900 110 65 110 65
1000 110 65 110 65
PS4
L
Z
Ø
PS4X
Centrum Klima – Products catalogue36
net mounted by spot weldingbranching connection (linear weld)net drawn, mesh 12x12 mm
•••
MATERIAL
PRODUCT CHARACTERISTICS
BRANCHING WITH NET BUS
galvanized steel•
siatka z oczkami 12x12
AE
ØD
DiameterØ (mm)
E(mm)
A(mm)
Items Set Package Packaging
100 45 95 65 P4
125 45 95 50 P4
150 45 95 30 P4
160 45 95 60 P2
200 45 95 50 P2
225 45 95 Z Z
250 45 95 30 P2
300 45 95 28 P1
315 45 95 28 P1
350 45 95 24 P1
DiameterØ (mm)
E(mm)
A(mm)
Items Set Package Packaging
355 45 95 24 P1
400 45 95 15 P1
450 45 95 9 P1
500 45 95 8 P1
560 65 97 Z Z
630 65 120 4 P1
710 65 120 Z Z
800 70 120 Z Z
900 70 120 Z Z
1000 70 120 Z Z
Z - information upon request
net with 12x12 mesh
Round fi ttings
Centrum Klima – Products catalogue 37
Round fi ttings
MATERIAL
CB/FB
stainless steel•
CB
Nominal diameterØ (mm)
E(mm)
100 40
125 40
150 40
160 40
180 40
200 40
225 40
250 40
280 40
300 40
315 40
355 40
400 40
450 40
500 40
branching connection (linear weld)•
PRODUCT CHARACTERISTICSA
EE
ØD
ØD
FB
CB
BRANCHING OVERLAYING ROUND/RECTANGULARE DUCT
FB
Nominal diameterØ (mm)
A(mm)
E(mm)
80 75 40
100 75 40
125 75 40
150 75 40
160 75 40
180 75 40
200 75 40
225 100 40
250 100 40
280 100 40
300 100 40
315 125 40
355 125 40
400 125 40
450 175 40
500 175 40
CB
FB
Centrum Klima – Products catalogue38
fusion welded (linear welding, spot welding)the gasket is fi tted in the fl anges (TSYX)
••
MATERIAL
PRODUCT CHARACTERISTICS
TWIN BEND TSY / TSYX
galvanized steelEPDM (TSYX) rubber gasket
••
Version with gasketTSYX
40
40
L = 50
D
D1
90°
40
40
D
D1
45°
40
40
L = 50
D
D1
120°
L = 5
0
Notice: actual D1 and D2 size are 2 mm smaller
TSY 90°
D(mm)
D1(mm)
Items Set Package Packaging
100 100 50 P2
125 100 35 P4
160 100 35 P4
125 125 42 P2
160 125 25 P2
200 125 40 P1
150 150 25 P2
160 160 50 P1
200 160 30 P1
200 200 28 P1
250 200 18 P1
TSY 90°
D(mm)
D1(mm)
Items Set Package Packaging
315 200 14 P1
400 200 35 P1
250 250 18 P1
315 250 10 P1
315 315 8 P1
355 355 6 P1
400 400 6 P1
450 450 L L
500 500 L L
560 560 L L
630 630 L L
L - sold by pcs.
Round fi ttings
Centrum Klima – Products catalogue 39
Round fi ttings
fusion welded (linear weld)gasket (VX) is positioned by fl anges
••
PRODUCT CHARACTERISTICSMATERIAL
COUPLING V / VX
galvanized steelEPDM (VX) rubber gasket
••
Version with gasketVX
ØD
H8
H (mm) Items Set Package
D (mm) V VX Weight
(kg) V VX Packaging
80 40 40 0,12 70 70 P12 100 40 40 0,15 112 90 P6 125 40 40 0,19 72 60 P6 140 40 40 0,20 55 86 P6 150 40 40 0,21 50 45 P6 160 40 40 0,23 70 60 P4 180 40 40 0,26 60 50 P4 200 40 40 0,29 54 40 P4 225 40 40 0,33 45 30 P4 250 40 40 0,37 72 55 P2 280 40 40 0,40 50 50 P2 300 40 40 0,43 46 45 P2 315 40 40 0,46 46 36 P2 350 40 40 0,50 55 55 P1 355 40 40 0,50 55 55 P1 400 46 50 0,67 50 50 P1 450 46 50 0,79 24 24 P1 500 46 50 0,88 24 24 P1 560 56 60 0,88 21 21 P1 600 71 60 0,93 17 16 P1 630 71 60 0,95 16 16 P1 710 71 60 1,05 15 15 P1 800 71 65 1,15 10 10 P1 900 71 65 1,60
1000 71 65 1,85 1250 71 65 2,05
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue40
fusion welded (linear weld) •
PRODUCT CHARACTERISTICSMATERIAL
COUPLING (STAINLESS STEEL) VN
stainless steel, 1.4301 EN 10088-2 •
D
H 8
Dimension (mm)
D (mm)
H (mm)
Weight (kg) Packaging Items
Set Package
100 98,8 40 0,15 P6 90
125 123,6 40 0,19 P6 60
160 158,7 40 0,20 P4 60
200 198,6 40 0,29 P4 40
250 248,5 40 0,37 P2 55
315 313,4 40 0,46 P2 40
Round fi ttings
Centrum Klima – Products catalogue 41
Round fi ttings
fusion welded (linear weld)•
MATERIAL PRODUCT CHARACTERISTICS
SLEEVE VF
galvanized steel•
ØD
H8
Tolerance: D ±5mm
D (mm) H (mm) Weight
(kg)Items Set Package Packaging
80 40 0,12 70 P12 100 40 0,16 112 P6 125 40 0,20 72 P6 140 40 0,21 55 P6 150 40 0,22 50 P6 160 40 0,24 70 P4 180 40 0,27 60 P4 200 40 0,30 54 P4 225 40 0,34 45 P4 250 40 0,39 72 P2 280 40 0,42 50 P2 300 40 0,45 46 P2 315 40 0,47 46 P2 350 40 0,58 55 P1 355 40 0,58 55 P1 400 46 0,69 50 P1 450 46 0,79 24 P1 500 46 0,87 24 P1 560 56 0,90 21 P1 600 71 0,93 16 P1 630 71 0,93 16 P1 710 71 1,08 15 P1 800 71 1,21 10 P1 900 71 1,65
1000 71 2,00 1250 71 2,25
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue42
fusion welded (linear weld) •
MATERIAL PRODUCT CHARACTERISTICS
SLEEVE (STAINLESS STEEL) VFN
stainless steel, 1.4301 EN 10088-2 •
D
H 8
Size (mm)
D (mm)
H (mm)
Weight (kg) Packaging Items
Set Package
100 100,5,8 45 0,16 P6 90
125 125,5 45 0,20 P6 60
160 160,6 45 0,24 P4 60
200 200,7 45 0,30 P4 40
250 250,8 45 0,39 P2 55
315 315,9 45 0,47 P2 40
Round fi ttings
Centrum Klima – Products catalogue 43
Round fi ttings
pressed/weldsingle element (D)handle mounted by spot welding (DXH)
•••
PRODUCT CHARACTERISTICS
MATERIAL
DUCT END CAP D / DX / DXH
galvanized steelEPDM (DX, DXH) rubber gasket
••
ØDD
DX
DXH
R
H
H H1
ØD
H H1
ØD
Version with gasket DX
Version with gasket and handle DXH
Pressed
Weld
ØD
D
DX
DXHH
H
ØD
H
ØD
Centrum Klima – Products catalogue44
D (pressed)
D[mm]
H*[mm]
R[mm]
waga[kg]
Items Set Package Packaging
80 20 5 0,04 150 P24
100 20 5 0,08 100 P24
125 20 5 0,09 70 P24
150 20 5 0,14 50 P24
160 20 5 0,14 50 P24
180 20 5 0,2
200 20 5 0,19 30 P24
250 20 5 0,27 20 P24
315 20 5 0,51 20 P24
355 20 5 0,65 15 P24
400 20 5 0,67 15 P24
D (weld)
D[mm]
H**[mm]
450 50
500 65
560 65
600 70
630 70
650 70
710 80
800 80
900 80
1000 100
1120 100
1250 100
DX/DXH (weld)
D[mm]
H**[mm]
450 52
500 65
560 65
600 70
630 70
650 70
710 83
800 83
900 83
1000 103
1120 103
1250 103
*Tolerance: ±5mm
**Tolerance: ±2mm
Round fi ttings
DX/DXH (pressed)
D[mm]
H*[mm]
R[mm]
Items Set Package Packaging
80 55 35 80 P24
100 55 35 110 P12
125 55 35 72 P12
150 55 35 50 P12
160 55 35 40 P12
200 55 35 50 P6
250 55 35 25 P6
315 55 35 25 P6
355 55 35 20 P4
400 55 35 20 P4
Centrum Klima – Products catalogue 45
pressed/weldsingle element (DF)handle mounted by spot welding (DFH)
•••
MATERIAL
PRODUCT CHARACTERISTICS
FITTING END CAP DF / DFH
galvanized steel•
Round fi ttings
Version with handleDFH
Part of class C air tightness certifi ced ventilation system.
ØD
H
ØD
R
R
H
DF
DFH
Pressed
Weld
DFH
ØD
ØDDFH
H
DF/DFH (pressed)
D[mm]
H*[mm]
R[mm]
waga[kg]
Items Set Package Packaging
80 40 4 0,06 75 P24
100 40 4 0,09 55 P24
125 40 4 0,11 80 P12
150 40 4 0,15 55 P12
160 40 4 0,16 45 P12
180 40 4 0,2
200 40 4 0,21 40 P12
250 40 4 0,34 30 P6
315 40 4 0,51 22 P6
355 40 4 0,63 25 P4
400 40 4 0,76 12 P6
*Tolerance: ±5mm
DF/DFH (weld)
D[mm]
H**[mm]
450 50
500 65
560 65
600 70
630 70
650 70
710 80
800 80
900 80
1000 100
1120 100
1250 100
**Tolerance: ±2mm
Centrum Klima – Products catalogue46
pressedsingle elementgasket (VX) is positioned by fl anges
•••
PRODUCT CHARACTERISTICSMATERIAL
STRAIGHT BRANCHING IL / ILX
galvanized steelEPDM (ILX) rubber gasket
••
W
H
ØD
Version with gasketILX
Round fi ttings
Z - information upon request Tolerance ±2mm
ILX
Nominal diameter ØD [mm]
W (mm)
H (mm)
Items Set Package Packaging
80 12 50 100 P12100 12 50 150 P6125 15 47 100 P6140 15 47 70 P6150 15 47 70 P6160 15 47 100 P4180 15 47 50 P6200 15 47 75 P4225 15 47 60 P4250 15 47 50 P4280 15 47 50 P4300 15 47 35 P4315 15 47 40 P4350 15 47 Z Z355 15 47 32 P4400 15 47 45 P2450 15 47 30 P2500 15 62 25 P2560 15 62 25 P2600 15 67 Z Z630 15 67 34 P1710 15 78 Z Z800 15 78 Z Z900 15 78 Z Z
1000 15 98 Z Z1120 15 98 Z Z1250 15 98 Z Z
IL
Nominal diameter ØD [mm]
W (mm)
H (mm)
Items Set Package Packaging
80 12 48 100 P12100 12 48 150 P6125 15 45 100 P6140 15 45 70 P6150 15 45 100 P4160 15 45 100 P4180 15 45 50 P6200 15 45 75 P4225 15 45 60 P4250 15 45 50 P4280 15 45 50 P4300 15 45 45 P4315 15 45 40 P4350 15 45 Z Z355 15 45 32 P4400 15 45 45 P2450 15 45 40 P2500 15 60 60 P1560 15 60 50 P1600 15 60 Z Z630 15 65 40 P1710 15 65 Z Z
800 15 85 Z Z900 15 85 Z Z
1000 15 85 Z Z
Centrum Klima – Products catalogue 47
IL4
Diameter Ø (mm)
L (mm)
W (mm)
Z (mm)
80 60 10 45
100 58 12 45
125 58 12 45
140 58 12 45
150 58 12 45
160 58 12 45
180 58 12 45
200 58 12 45
225 58 12 45
250 58 12 45
280 58 12 45
300 58 12 45
315 58 12 45
355 58 12 45
400 58 12 45
450 88 12 55
500 88 12 55
560 88 12 65
630 88 12 65
used as 45° passing for rectangular ductsfusion welded (linear weld)fl anges are clamped on the gasket (IL4X)
•••
MATERIAL PRODUCT CHARACTERISTICS
45° CYLINDRICAL BRANCHING IL4 / IL4X
galvanized steelEPDM (IL4X) rubber gasket
••
Round fi ttings
Version with gasketIL4X
L
Z
Ø
W
IL4
L
Z
Ø
W
IL4X
IL4X
Diameter Ø (mm)
L (mm)
W (mm)
Z (mm)
80 67 60 40
100 65 58 40
125 65 58 40
140 65 58 40
150 65 58 40
160 65 58 40
180 65 58 40
200 65 58 40
225 65 58 40
250 65 58 40
280 65 58 40
300 65 58 40
315 65 58 40
355 65 58 40
400 65 58 50
450 95 88 50
500 95 88 50
560 95 88 60
630 95 88 60
Centrum Klima – Products catalogue48
pressedsingle element
••
MATERIAL PRODUCT CHARACTERISTICS
PRESSED STRAIGHT BRANCHING ILR / ILRX
galvanized steelEPDM (ILRX) rubber gasket
••
Version with gasketILRX
20±10
H
R
D
D
Size (mm)
D (mm)
H (mm)
R (mm)
Weight (kg)
PackagingItems
Set Package
80 78,8 45 12 0,10 P12 70
100 98,8 45 15 0,14 P12 40
125 123,8 45 20 0,18 P6 50
150 148,8 45 20 0,22 P6 45
160 158,8 45 25 0,27 P4 50
200 198,8 45 25 0,31 P4 50
250 248,8 45 25 0,37 P2 70
315 313,8 45 25 0,47 P2 44
Round fi ttings
Centrum Klima – Products catalogue 49
Z H
ØD
mesh fi xed with spot weldbranching connection (linear weld)drawn metal mesh, openings 12x12 [mm]
•••
MATERIAL PRODUCT CHARACTERISTICS
NET STRAIGHT BRANCHING
galvanized steel•
SO
Round fi ttings
Diameter Ø (mm)
H(mm)
Z(mm)
Items Set Package
Packaging
80 55 40 65 P24
100 55 40 40 P24
125 55 40 63 P12
140 55 40 40 P12
150 55 40 40 P12
160 55 40 35 P12
180 55 40 35 P12
200 55 40 50 P6
225 55 40 35 P6
250 55 40 30 P6
280 55 40 30 P6
300 55 40 25 P6
315 55 40 20 P6
Diameter Ø (mm)
H(mm)
Z(mm)
Items Set Package
Packaging
350 55 40 20 P6
355 55 40 20 P6
400 55 40 20 P4
450 55 40 40 P2
500 65 50 25 P2
560 65 50 25 P2
600 65 50 Z Z
630 80 60 Z Z
710 80 60 Z Z
800 80 60 Z Z
900 80 60 Z Z
1000 80 60 Z Z
Z - information upon request
Centrum Klima – Products catalogue50
ALUMINUM FLEXIBLE DUCT, NON-INSULATED AF012
TYPE AF 012
Spiral lead 24 mm
Diameter range 65-635 mm
Operating temperature range -30/+140 °C
Maximum air speed 30 m/s
Maximum operating Pressure 2500 Pa
Standard length 10 m
Cardboard Package 0,5 m
standard 10 m long ducts fi tted into 0.5 m cardboard boxeslow transportation and storage costeasy assemblyno need to use special tools for cutting or fi xingdoes not emit toxic gases in high temperaturesproduct’s fi re resistance is certifi ed by European certifi catesPolish Hygienic Certifi cate
•
•••••
•
USEPRODUCT ADVANTAGES
This duct has been designed to transport air in both AC and ventilation duct systems. Attenuates system’s vibra-tion. Reduces the need to use fi ttings.
DESIGN
Three-layer laminate with Polyester. Extremely resistant to mechanical damage.The duct is reinforced with a steel wire spiral (lead 24 mm).
Note - duct characteristics on Page 60
Flexible ducts
Centrum Klima – Products catalogue 51
Flexible ducts
ALUMINUM FLEXIBLE DUCT, INSULATED AF013/ AF019
standard 10 m long ducts fi tted into 1 m cardboard boxeslow transportation and storage costeasy assembly no need to use special tools for cutting or fi xingdoes not emit toxic gases in high temperaturesproduct’s fi re resistance is certifi ed by European certifi catesPolish Hygienic Certifi cate
•
•••••
•
USEPRODUCT ADVANTAGES
Flexible duct with thermal insulation and sound attenua-tion are designed especially to transport air in ventilation and AC systems. Thanks to perforation of the internal duct, the noise generated by the assembly is reduced. Reduces systems’ vibrations. Reduces the need to use fi ttings.
TYPE AF 013 / AF 019
Internal duct AF012 (Perforated)
Insulation 20 kg/m3 25 mm mineral wool*
External cover Aluminum, Polyester
Diameter range 83-635 mm
Operating temperature range -30/+140 °C
Maximum air speed 30 m/s
Maximum operating Pressure 2000 Pa
Standard length 10 m
Cardboard Package 1 m
Note: duct characteristics on Page 60
AF013 AF019
DESIGN
Internal layer of the AF 013/AF 019 duct is made of slightly perforated AF 012 duct. Insulation material is mineral wool while the external cover is made of three-layer laminate reinforced by carbon fi ber. AF 013 duct has additional steam insulation foil between the internal duct and insulation layer made of Polyester.
* also available with 50 mm insulation
Centrum Klima – Products catalogue52
NOT INSULATED FLEXIBLE DUCTS AF012ECO
TYPE AF 012ECO
Spiral lead 24 mm
Diameter range 83-635 mm
Operating temperature range -30/+140°C
Maximum air speed 30 m/s
Maximum operating Pressure 2500 Pa
Standard length 10 m
Cardboard Package 0,5 m
standard ducts with the length of 10 meters, put very tight in the 0,5 m cardboard boxeslow costs of logistics and transportationeasy assemblyno necessity to use any special tool for cutting or fasteningno emission of the toxic gases in the high tem-peratures
•
•••
•
USEPRODUCT ADVANTAGES
Duct is built of the aluminium laminated with the po-lyester. It was designed especially for the needs of the ventilation and air conditioning market.
DESIGN
Two layers of the aluminium laminated with the po-lyester with the coil made of the spring wire.
Note - duct characteristics on Page 60
Flexible ducts
Centrum Klima – Products catalogue 53
Flexible ducts
INSULATED FLEXIBLE DUCTS AF013ECO AF019ECO
standard ducts with the length of 10 meters, put very tightly in the carton package up to 1 mlow costs of the logistics and transportationeasy assembly, also above the circular or oval ductsno necessity to use any special tool for cutting or fasteningno emission of the toxic gases in the high tempera-tures
•
•••
•
USEPRODUCT ADVANTAGES
AF013ECO/AF019ECO - duct insulated thermally and acousti-cally, designed especially for the needs of the ventilation and air conditioning market. It was created for reducing the noise level in the ventilation system.
TYPE AF013ECO / AF019ECO
Internal duct AF012ECO (perforated)
Insulation 20 kg/m3 glass wool 25 mm*
External cover Aluminium, Polyester
Diameter range 83-635 mm
Operating temperature range -30/+140 °C
Maximum air speed 30 m/s
Maximum operating pressure 2000 Pa
Standard length 10 m
Cardboard package 1 m
DESIGN
Inner layer of the duct AF013ECO/AF019ECO is built with the light perforated duct AF012ECO. Insulation coat is comprised of the glass wool and the outer protection is built with the two-layer coat of the laminated aluminium strengthened with the glass fi bre. AF013ECO duct com-prises additionally the steam-proof inner layer of the polyester foil.
* available also with the insulation of 50 mmNote: duct characteristics on Page 60
Centrum Klima – Products catalogue54
ALUMINUM FLEXIBLE DUCT, NON-INSULATED M0
TYPE M0
Spiral lead 24 mm
Diameter range 65-635 mm
Operating temperature range -30/+250 °C
Maximum air speed 30 m/s
Maximum operating pressure 3000 Pa
Standard length 10 m
Cardboard package 0,5 m
completely non-combustible fl exible aluminum ductthanks to thicker aluminum layer the duct’s stiff -ness and durability are increased as compared to a traditional fl exible ductstandard 10 m long ducts are individually sacked into 0.5 m cardboard boxeslow transportation and storage costeasy assemblyno need to use special tools for cutting or fi xingdoes not emit toxic gases in high temperaturesproduct’s fi re resistance is certifi ed by European certifi catesPolish Hygienic Certifi cate
•
•
•
•••••
•
USEPRODUCT ADVANTAGES
This duct has been designed to transport air in both AC and ventilation duct systems. It can also be used to transport hot air of temperature up to +250°C. Completely non-fl ammable. Attenuates system’s vibration. Reduces the need to use fi ttings.
DESIGN
Two layer aluminum foil glued with non-fl ammable glue. Fused steel wire spiral with 24 mm lead. Total thickness 0,10 mm, total density 230 g/m³.
Note: duct characteristics on Page 60
Flexible ducts
Centrum Klima – Products catalogue 55
Flexible ducts
M0IZO ALUMINUM FLEXIBLE DUCT, INSULATED M0izo
completely non-combustible fl exible aluminum ductinternal layer does not contain any Polyesterthanks to thicker aluminum layer the duct’s stiff -ness, hardness and durability are increased as compared to a traditional fl exible ductstandard 10 m long ducts are individually sacked into 1 m cardboard boxeslow transportation and storage costeasy assemblyno need to use special tools for cutting or fi xingdoes not emit toxic gases in high temperaturesproduct’s fi re resistance is certifi ed by European certifi catesPolish Hygienic Certifi cate Polish Fire Classifi cation (ITB) concerning fi re resistance
•••
•
•••••
••
USEPRODUCT ADVANTAGES
This fl exible and thermally insulated duct has been es-pecially designed for ventilation and AC market. Thanks to its thermal resistance and non combustibility, it can also be used to transport hot air of temperature up to +250°C including distribution of hot air from fi re places. Attenuates system’s vibration. Reduces the need to use fi ttings and provides thermal insulation.
TYPE M0izo
Internal duct MO (non Perforated)
Insulation 20 kg/m3 25 mm mineral wool
External cover reinforced aluminum, Polyester
Diameter range 83-635 mm
Operating temperature range -30/+250 °C
Maximum air speed 30 m/s
Maximum operating pressure 3000 Pa
Standard length 10 m
Cardboard package 1 m
Note: duct characteristics on Page 60
DESIGN
The internal layer of MO duct (insulated) is made of non-perforated MO duct. Two layer aluminum foil glued with non-fl ammable glue. Fused steel wire spiral with 24 mm lead. Insulation material is mineral wool and the external cover is made of multi layer laminated alumi-num reinforced with carbon fi bre.
Centrum Klima – Products catalogue56
SEMI FLEXIBLE ALUMINUM DUCT NON - INSULATED S-FLEX®
TYPE S–FLEX®
Material aluminum
Aluminum tape thickness 0,09 mm
Diameter range 80-630 mm
Operating temperature range -30/+280 °C
Maximum air speed 25 m/s
Maximum operating pressure 2000 Pa
Standard length 3 m
Compresed duct length0,8 m
(at maximum compression 0,6 m)
USE
Semi flexible non-insulated duct. Due to a wide range of possible uses, this product can be used in AC and ventilation systems and for other industrial purposes.
DESIGN
S-Flex is a product used in the construction of ventila-tion and air conditioning installations. Due to its high mechanical durability the product proves indispensible also in the installations of industrial facilities. Perfec-ted technical parameters, high fl exibility and special design enable to install ducts without the necessity to use special tools or fi ttings.
Note: duct characteristics on Page 60
90 mm
S-fl ex® duct by Centrum Klima S.A.
1. Non-durable seam2. Material thickness below 0,10 mm3. 5 compression grooves4. A traditional duct is manufactured from a
narrow 54 mm wide aluminium tape. It means more seams (up to 55 seams on 3 m standard length), making the duct less fl exible, more prone to damages and less compressible.
1. High-quality durable interlock seam2. Aluminium tape thickness 0,09 mm3. 10 compression grooves4. S-Flex duct is manufactured from wide (90mm)
aluminium tape. Thanks to this the number of seams is limited by 40%, the duct is more fl exible and durable and easy to compress.
54 mm
1
2
3
4
Traditional duct
1
2
3
4
Flexible ducts
Centrum Klima – Products catalogue 57
Flexible ducts
P1
P2
* S-Flex semi-fl exible duct is also available in 315 and 400 mm diameters. The product is sold individually upon orders.
P
P2
Code Length(mm)
Width (mm)
Height (mm)
Weight(kg)
Volume (m³)
Packaging/pallet
P1 1200 800 800 4,63 0,770 max 3
P2 600 800 800 2,83 0,380 max 6
Packaging method for S-Flex® for the following diameterslength 3000 mm
Size Box type Number of items /box
Weight(kg/piece.)
Weight(kg/box)Diameter (mm) Length (mm)
80 3000 P1 125 0,366 49
80 3000 P2 54 0,366 23
100 3000 P1 81 0,459 42
100 3000 P2 42 0,459 22
120 3000 P1 53 0,550 33
125 3000 P1 53 0,573 34
130 3000 P1 48 0,594 33
150 3000 P1 38 0,687 30
160 3000 P1 32 0,756 28
180 3000 P1 24 0,825 24
200 3000 P1 20 0,915 23
250 3000 P1 13 1,146 19
315 3000 P1 5 1,400 12
400 3000 P1 3 1,800 5,4
Packaging method for S-Flex® for the following diameterslength 5000 mm
Size Box type Number of items /box
Weight(kg/piece.)
Weight(kg/box)Diameter (mm) Length (mm)
80 5000 P1 72 0,611 48
100 5000 P1 52 0,765 44
120 5000 P1 30 0,910 32
125 5000 P1 30 0,955 33
130 5000 P1 28 0,991 32
150 5000 P1 23 1,145 31
160 5000 P1 20 1,261 30
180 5000 P1 16 1,375 27
200 5000 P1 12 1,525 23
250 5000 P1 9 1,911 22
Centrum Klima – Products catalogue58
FLEXIBLE PVC DUCT POLYFLEX HEAVY DUTY
standard 10 m long ducts are individually sacked into 0.5 m cardboard boxeslow transportation and storage costeasy assemblyno need to use special tools for cutting or fi xingdoes not produce toxic gases in high temperaturessmooth internal surfaceextremely resistant to mechanical damage
•
••••••
USEPRODUCT ADVANTAGES
This duct is designed to be installed in low and medium pressure ventilation and AC systems. Attenuates system’s vibration. Reduces the need to use fi ttings. This duct is characterized by high fl exibility and durability in case of multiple reshaping and relocations.
TYPE POLYFLEX PVC
Spiral lead 24 mm
Diameter range 83-508 mm
Operating temperature range -10/+75 °C
Maximum air speed 30 m/s
Maximum operating pressure 3000 Pa
Standard length 10 m
Cardboard package 0,5 m
Note: duct characteristics on Page 60
DESIGN
80 micrometers thick multilayer reinforced PVC. Fused steel wire spiral with 24 mm lead.80 micrometers thick – black
Flexible ducts
Centrum Klima – Products catalogue 59
Flexible ducts
FLEXIBLE PVC LAMINATED DUCT COMBIFLEX
TYPE COMBIFLEX PVC
Spiral lead 24 mm
Diameter range 80-630 mm
Operating temperature range -10/+140 °C
Maximum air speed 30 m/s
Maximum operating pressure 3000 Pa
Standard length 10 m
Cardboard package 0,75 m
Note: duct characteristics on Page 60
high mechanical durability and resistance to high temperaturesstandard 10 m long ducts are individually sacked into 0.75 m cardboard boxeslow transportation and storage costeasy assemblyno need to use special tools for cutting or fi xingPolish Hygienic Certifi cate
•
•
••••
USEPRODUCT ADVANTAGES
COMBIFLEX duct is designed to transport air in duct sys-tems. Thanks to the internal aluminum coating, COMBIFLEX is resistant to high temperatures. The external PVC coating ensures mechanical durability. This duct is characterized by high fl exibility and durability in case of multiple reshap-ing and relocations.
DESIGN
Multilayer aluminum and polyester laminate with additional 70 micrometers thick PVC coating. Fused steel wire spiral with 24 mm lead.
Centrum Klima – Products catalogue60
50
0,3
0,40,50,6
0,8
1,01,0
1,5
2,0
3,0
4,0
5,06,0
8,0
10
15
20
30
40
50
60
80
100
15 20 30 40 50 100 150 200 300 400 500 1000 1500 2000 5000l/s
m /h3
Wydatek powietrza q
Stra
ta c
iśni
enia
Pa/
m
Śr. n
omin
alna
[mm
]
100 200 300 500 1000 2000 5000 10000 18000
630
550
500
450
400
35528020016012580
315250180140100
Pręd
kość
m/s
3,0
3,5
4,0
5,0
6,0
7,0
8,0
10
15
DUCT SPECIFICATIONS
AF 012, AF 013, AF 019, AF 012ECO, AF 013ECO, AF 019ECO, S–FLEX®, POLYFLEX PVC, COMBIFLEX PVC, M0, M0 izo
Pres
sure
loss
Pa/
m
Linear pressure lost chart
r=d/210080
504030
20
15
108
543
2
13Prędkość m/s
Stra
ta c
iśni
enia
Pa
4 5 6 7 8 9 10 12 14 15
r=d
r=1,5d
r=2d
Pres
sure
loss
Pa
Speed m/s
Air volume q
Nom
inal
dia
met
er (m
m)
Local pressure lost on bends and elbows - chart
Length AF 013 L=2000 (mm)
dB (A)Reduction of the
noise level through the ducts walls
Noise silencing
Frequency (Hz) 1/3 okt. 1/1 okt 1/3 okt. 1/1 okt
100 16,1 31,6
125 19,7 18,4 28,5 29,1
160 21,0 27,9
200 18,8 29,1
250 17,5 15,2 31,6 31,5
315 12,3 37,3
400 13,9 38,4
500 11,1 10,8 39,0 38,9
630 8,8 39,3
800 9,5 39,2
1000 9,0 9,3 41,0 40,9
1250 9,3 43,6
1600 10,3 44,3
2000 11,1 11,1 48,2 46,7
2500 12,2 49,5
3150 13,9 43,9
4000 17,6 16,3 35,4 32,8
5000 19,3 29,1
Boxes on pallet (pc)
Dimeter AF 012/AF 012ECO
AF 019/AF 019ECO
AF 013/AF 013ECO M0 M0 izo COMBIFLEX
80 300 90 90 300 90 300
102 280 48 48 240 48 240
127 204 44 44 170 44 170
152 130 30 30 130 30 130
162 130 27 27 130 27 130
178 88 27 27 77 27 77
203 88 24 24 77 24 77
229 54 14 14 54 14 54
254 54 14 14 54 14 54
280 35 12 12 35 12 35
305 35 12 12 35 12 35
315 35 12 12 35 12 35
356 30 12 12 30 12 30
406 24 8 8 25 8 25
457 16 4 4 16 4 16
508 8 3 3 8 3 8
560 8 3 3 8 3 8
635 8 3 3 8 3 8
Flexible ducts
m3/h
Centrum Klima – Products catalogue 61
MATERIAL
SINGLE BLADE ROUND DAMPER
galvanized steelEPDM (DSX) rubber gasket
••
DS / DSX
D
LE
Version with gasketDSX
Dampers
branching connection fusion welded (linear weld)possibility of with diff erent types of mechanism
•••
PRODUCT CHARACTERISTICS
Damper with mechanism MPJ *
* version with gasket
Damper with mechanism SPIRO *
Damper for actuators *
Part of class C air tightness certifi ced ventilation system.
DS
D [mm]
SP MPJ Items Set Package
Packaging D [mm]
for actuators
L [mm] E [mm] L [mm] E [mm] L [mm] E [mm]
80 90 40 110 30 60 P6 80 220 40100 90 40 110 30 40 P6 100 220 40125 90 40 110 30 27 P6 125 220 40140 90 40 110 30 Z Z 140 220 40150 90 40 110 30 30 P4 150 220 40160 90 40 110 30 24 P4 160 220 40180 90 40 110 30 20 P4 180 220 40200 90 40 110 30 36 P2 200 220 40225 80 45 110 30 30 P2 225 220 40250 130 45 140 40 36 P1 250 220 40280 130 45 140 40 32 P1 280 220 40300 130 45 140 40 25 P1 300 220 40315 130 45 140 40 25 P1 315 220 40350 130 45 140 40 Z Z 350 220 40355 130 45 140 40 20 P1 355 220 40400 130 45 120 50 15 P1 400 200 50450 120 50 120 50 10 P1 450 200 50500 120 50 120 50 Z Z 500 200 50
Z - information upon request Tolerance ±5mm
Centrum Klima – Products catalogue62
Dampers
DS
D [mm]
SP MPJ Items Set Package
Packaging D [mm]
for actuators
L [mm] E [mm] L [mm] E [mm] L [mm] E [mm]
560 100 60 100 60 Z Z 560 180 60600 100 60 100 60 Z Z 600 180 60630 100 60 100 60 Z Z 630 180 60710 130 60 130 60 Z Z 710 180 60800 120 65 120 65 Z Z 800 170 65900 170 65 170 65 Z Z 900 220 65
1000 170 65 170 65 Z Z 1000 220 651250 170 65 170 65 Z Z 1250 220 65
DSX
D [mm]
SP MPJ Items Set Package
Packaging D [mm]
for actuators
L [mm] E [mm] L [mm] E [mm] L [mm] E [mm]
80 90 40 110 30 60 P6 80 220 40100 90 40 110 30 40 P6 100 220 40125 90 40 110 30 27 P6 125 220 40140 90 40 110 30 Z Z 140 220 40150 90 40 110 30 30 P4 150 220 40160 90 40 110 30 24 P4 160 220 40180 90 40 110 30 20 P4 180 220 40200 90 40 110 30 36 P2 200 220 40225 90 40 110 30 30 P1 225 220 40250 140 40 140 40 36 P1 250 220 40280 140 40 140 40 32 P1 280 220 40300 140 40 140 40 25 P1 300 220 40315 140 40 140 40 25 P1 315 220 40350 140 40 140 40 Z Z 350 220 40355 140 40 140 40 20 P1 355 220 40400 120 50 120 50 15 P1 400 200 50450 120 50 120 50 10 P1 450 200 50500 120 50 120 50 Z Z 500 200 50560 100 60 100 60 Z Z 560 180 60600 100 60 100 60 Z Z 600 180 60630 100 60 100 60 Z Z 630 180 60710 130 60 130 60 Z Z 710 180 60800 120 65 120 65 Z Z 800 170 65900 170 65 170 65 Z Z 900 220 65
1000 170 65 170 65 Z Z 1000 220 651250 170 65 170 65 Z Z 1250 220 65
Centrum Klima – Products catalogue 63
AIR-TIGHT SINGLE-LEAF ROUND DAMPER DSXS
welded (linear weld)•
MATERIAL PRODUCT CHARACTERISTICS
galvanized steelEPDM rubber gasketrubber gasket for air-tight dampers
•••
Z - information upon request
D [mm]
SP for actuators Items Set Package
PackagingL [mm] E [mm] L [mm] E [mm]
80 90 40 220 40 60 P6
100 90 40 220 40 40 P6
125 90 40 220 40 27 P6
150 90 40 220 40 30 P4
160 90 40 220 40 24 P4
180 90 40 220 40 36 P4
200 90 40 220 40 36 P2
225 90 40 210 45 60 P1
250 140 40 210 45 50 P1
280 140 40 210 45 40 P1
300 140 40 210 45 32 P1
315 140 40 210 45 32 P1
355 140 40 210 45 24 P1
400 120 50 210 45 15 P1
450 120 50 190 55 10 P1
500 120 50 190 55 Z Z
560 100 60 170 65 Z Z
630 100 60 170 65 Z Z
710 130 60 170 65 Z Z
800 120 65 170 65 Z Z
900 170 65 170 65 Z Z
1000 170 65 170 65 Z Z Tolerance ±5mm
Dampers
Part of class C air tightness certifi ced ventilation system.
Centrum Klima – Products catalogue64
welded (linear weld) •
MATERIAL PRODUCT CHARACTERISTICS
SINGLE-LEAF ROUND DAMPER (STAINLESS STEEL)
stainless steel, 1.4301 EN 10088-2 •
D(mm)
L(mm)
E(mm)
Items Set Package
Packaging
100 90 40 40 P6
125 90 40 27 P6
160 90 40 36 P4
200 90 40 36 P2
250 140 40 50 P1
315 140 40 32 P1
DSN
Tolerance ±2mm
Dampers
Centrum Klima – Products catalogue 65
Dampers
DESCRIPTION
DUCT DAMPER TYPE IRIS IRIS
With the IRIS damper the intensity of air fl ow may be continuously adjusted. Adjustment is done with a handle located on the damper which changes the diameter of the opening in the damping orifice. The damper is supplied with two endings which may be used to connect instrumentation measuring the intensity of air fl ow. The damper is also supplied with a gasket which tightens the connection with the system.
øD
Type Ød (mm) ØD (mm) L (mm) A (mm) B (mm)
100 99 165 110 30 32
125 124 210 110 30 42
160 159 230 110 30 35
200 199 285 110 30 42
250 249 335 135 40 42
315 314 410 135 40 47
400 398 525 190 60 62
AA
B
L
70
ød
Centrum Klima – Products catalogue66
IRIS SPECIFICATIONS
100
30
6 200
40
100 150
200
10
100
10
100
100
5015
50
30
300
30
30
300
20
200
20
20
200
40
400
40
40
400
50
500
50
50
500
70
300
1000
[l/s]
[l/s]
[l/s]
[l/s]
[l/s]
Q
Q
Q
Q
Q
500
200
20
500
200
[m3/h]
[m3/h]
[m3/h]
[m3/h]
[l/s]
[l/s]
Q
Q
[m3/h]
[m3/h][m3/h]
50
500
50
50
500
100
1000
100
100
1000
40
400
40
400
400
300
300
30
300
300
200
2000
200
200
2000
100
300 500
1000
3000
)aP(
Pt
)aP(
Pt
)aP(
Pt
)aP(
Pt
)aP(
Pt
Measureopening
Measureopening
Measureopening
Measure
ƒ
opening
Measureopening
[Pa]
[Pa]
[Pa]
[Pa]
[Pa]
dB(A)
dB(A)
dB(A)
dB(A)
dB(A)
IRIS 125
IRIS 200
IRIS 100
IRIS 160
IRIS 250
300
300
300
300
300
200
200
200
200
200
100
100
100
100
100
30
30
30
30
30
40
40
40
40
40
10
10
10
10
10
20
20
20
20
20
50
50
50
50
50
1
1
1
1
1
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
6
78
78
78
78
78
45
50
55
45
5055
45
5550
45
5055
45
50 55 60
40
40
40
40
40
35
35
35
35
35
30
30
30
30
30
25
25
25
25
25
1000
1000100
100
1500300
300
200
200
400 500
500
70
2000
2000
9000
500
500
1000
3000
400
5000
300
0002
00053000
1000
)aP(
Pt
)aP(
Pt
Measureopening
Measureopening
[Pa]
[Pa]
dB(A)
dB(A)
IRIS 315
IRIS 400
300
300
200
200
100
100
30
30
40
40
10
10
20
20
50
50
1
1
2
2
3
3
4
4
5
5
6
6
78
78
45
50
55
60
455055 6065
40
40
35
35
30
30
25
25
Dampers
Centrum Klima – Products catalogue 67
Dampers
BACK DRAFT DAMPER RSK
the blade is equipped with a closing springmay be installed in any position
••
PRODUCT CHARACTERISTICS
galvanized steel•
Size A(mm)
L(mm)
B(mm)
C(mm)
100 99 88 38 38
125 124 88 38 38
150 149 88 38 38
160 159 88 38 38
200 199 88 38 38
250 249 128 59 59
315 314 128 59 59
355 354 197 75 75
400 399 197 75 75
D
LØ AB C
DESCRIPTIONMATERIAL
PRESSURE LOST DIAGRAM
100
80
60
40
20
0000200202 30
p(Pa)
Ø80
Ø10
0
Ø12
5
Ø16
0
Ø20
0
Ø25
0
Ø31
5
0003003 000500505 0001001 [m³/h]
Back draft damper for round ducts is made of galvani-zed steel. The damper’s blades (oscillating) are closed by a spring which allows for assembly in any position. Used to allow fl ow of air in one direction only.
Centrum Klima – Products catalogue68
Standard length of the dampers:L = 200 mm, H = do 250 mmL = 250 mm, H = 250 ÷ 500L = 300 mm, H = 510 ÷ 710L = 400 mm, H = 711 ÷ 1000L = 500 mm, H = 1001 ÷ 1300L = 600 mm, H = 1301 ÷ 1600L = 700 mm, H = 1601 ÷ 2000
SINGLE BLADE RECTANGULAR DAMPER PJ
the damper’s frame is made of shapes and a cornersize of the shapes and corner depends on the damper’s sectionas standard manufactured with MPJ mechanism, possible manufacturing with KS mechanism or for actuator
•
•
•
MATERIAL
PRODUCT CHARACTERISTICS
galvanized steel•
LB
H
H (mm) 300 – 2000
B (mm) 300 – 1400
Dampers
Centrum Klima – Products catalogue 69
Dampers
MULTI BLADE RECTANGULAR DAMPER PW
driving mechanism is completely covered inside the side shapethe dampers are produced in manually powered (R) or actuator powered version (E)the multi blade damper with B ≥1400 mm is produced as diviled damper B < 3000 mmdue to transportation limits, one of the dimen-sions (B or H) cannot exceed 2000 mmoperating temperature range:
– 20°C ÷ + 80°C standard – 35°C ÷ + 140°C high temperature
•
•
•
•
•
MATERIAL
DESCRIPTION
aluminum coveraluminum louver slatsdriving cogs made of PA material
This damper is also available in high temperature version with frame (PWT).
•••
B30
20
L=115 mm
110
mm
H
H (mm) 300 – 2000
B (mm) 300 – 1400
MATERIAL
aluminum (cover + louver)PA material (driving cogs)rubber (gaskets, louver)
•••
Split damperB 1400>
Single manual mechanism or actuator motor 210 mm < H < 1612 mm
Double manual mechanism or two actuator motors 1612 mm < H < 3214 mm
Centrum Klima – Products catalogue70
MULTI BLADE DAMPER PW
ASSEMBLY DRAWING
PS 110
PS 100
PS 120(pod siłownik)
BKP 7
PS 130
KL 7R
S 06
CPS 93
CPS 93
6A12T
(actuator powered)
Dampers
Centrum Klima – Products catalogue 71
Dampers
AUTOMATIC ALUMINUM DAMPERS PSE / PSK
Automatic dampers are produced in duct version or wall version. Wall version of the damper operates as an exhauster and the duct damper serves as a control damper. The louvers are equipped with attenuating gaskets which prevents their edges from hitting against one another during standard operation. Thanks to that, the louvers do not make additional noise during op-eration.The dampers are entirely made of aluminum shapes (light and resistant to environment). Max. operating temperature: +80°C.
MATERIAL
DESCRIPTION
shape – aluminiumlouver – aluminiumlouver drives –plasticattenuating gasket
NOTES: Aluminum prevents the occurrence of corro-sion. Aluminum shapes and louvers guarantee low weight of the elements.
••••
wall version PSE
* duct version - PSK
X
H
B
L
B
H
x
H (mm) 300 – 2000
B (mm) 300 – 1400It is possible to produce any damper which fi ts into the dimensions (B and H) given above.
PSK
PSE
B: -20 H: -20
x= 52 L=57
ASSEMBLY DRAWING*
LouverSide shape
Gasket
Mechanism frame
M5x25 screw UP/DOWN shape
Centrum Klima – Products catalogue72
suitable for high, medium and low pressure applicationscomprehensive size rangeeff ective progressive action camlocksthermally and acoustically insulatedfast and simple to installcomplete with sealing gaskets“safe-edge” radiused tabs on frame.
•
••••••
PRODUCT CHARACTERISTICS
ACCESS DOOR FOR A RECTANGULAR DUCT RD
A
B25
The range of RD series access door is designed to provide rapid access to smoke, fi re and volume control dampers or other equipment mounted inside ductwork or associated plant. All door panels are of double skin construction completely enclosing the 25mm thick high density insulation.
DESCRIPTION
Type Nominal size A × B [mm]
Duct opening size [mm]
RD 15 150 × 150 120 × 120
RD 20 200 × 200 170 × 170
RD 21 200 × 125 170 × 95
RD 25 250 × 250 220 × 220
RD 30 300 × 300 270 × 270
RD 31 300 × 150 270 × 120
RD 32 300 × 200 270 × 170
RD 35 350 × 350 320 × 320
RD 40 400 × 400 370 × 370
RD 42 400 × 200 370 × 170
RD 425 400 × 250 370 × 220
RD 43 450 × 300 420 × 270
RD 44 400 × 300 370 × 270
RD 45 450 × 450 420 × 420
RD 50 500 × 500 470 × 470
RD 63 600 × 300 570 × 270
RD 64 600 × 400 570 × 370
RD 65 600 × 450 570 × 420
RD 66 600 × 600 570 × 570
Ventilation equipment
Centrum Klima – Products catalogue 73
Ventilation equipment
MATERIAL
CLEANOUT HATCHES KR
galvanized steelrubber gasket
••
D
A
B
D(mm)
A(mm)
B(mm)
100 180 80
125 180 80
160 250 150
200 250 150
250 250 150
315 250 150
355 250 150
400 250 150
adapted to assembly on round ductseasily accessible inspection hatch for cleaning the ducts, etc.easy assemblya sizer is included in the set, which allows cutting the appropriate opening in the round duct
••
••
PRODUCT CHARACTERISTICS
D(mm)
A(mm)
B(mm)
400 400 300
450 400 300
500 400 300
560 400 300
630 400 300
710 400 300
800 400 300
Centrum Klima – Products catalogue74
INSPECTION HATCHES ON RECTANGULAR DUCT FAD
adapted to assembly on rectangular ductseasily accessible inspection hatch for cleaning the ducts, etc.easy installation
••
•
MATERIAL
PRODUCT CHARACTERISTICS
galvanized steelrubber gasket
••
A
B
A(mm)
B(mm)
180 80
200 100
300 150
300 200
400 300
500 300
500 400
600 450
Ventilation equipment
Centrum Klima – Products catalogue 75
Ventilation equipment
ROUND INTAKE / EXHAUSTER KWO-AL
KWO-AL may work as intake or exhaustermade by aluminum - no corrosionnot paintedinternal security net
••••
MATERIAL
PRODUCT CHARACTERISTICS
aluminum•
H
5
Ød
ØD
Ød (mm)
ØD (mm)
H (mm)
Weight (g)
80 96 15 100
100 125 20 235
125 150 20 325
160 185 20 390
200 225 20 580
250 275 20 970
315 350 20 1895
400 435 35 3000
500 540 40 4500
Centrum Klima – Products catalogue76
ROUND INTAKE / EXHAUSTER (CrNi steel) VLA
VLA may work as intake or exhaustermade by CrNi steel - no corrosionnot paintedcover secure against weather’s conditionshigh quality and new designfast and easy assembling
••••••
MATERIAL
PRODUCT CHARACTERISTICS
CrNi steel•
A
C
B
TYPE ØD (mm)
ØA (mm)
ØB (mm)
C (mm)
VLA-100 100 97 133 52
VLA-125 125 120 165 52
VLA-150 150 145 192 62
VLA-160 160 155 192 62
VLA-200 200 195 253 62
Ventilation equipment
Centrum Klima – Products catalogue 77
Ventilation equipment
X
H
B
L
suitable for powder painting•
MATERIAL
PRODUCT CHARACTERISTICS
GALVANIZED STEEL RECTANGULAR AIR INTAKE/EXHAUSTER CW
galvanized steelsteel shapes system
••
B x H size of the air intake assembly hole
B: -20mm H: -20mm X=40mm L=62mm
H (mm) 300 – 2000
B (mm) 150 – 4000Min. height of the air intake H = 150 mmMax. size of the air intake H x B = 2000 mm x 4000 mm
68 mm
ASSEMBLY DRAWING
80
80
62
16
4068
66,8 85
BR 40 BR 40/62
LP 66 LP 88
Centrum Klima – Products catalogue78
X
H
B
L
MATERIAL
ANODIZED ALUMINUM RECTANGULAR AIR INTAKE / EXHAUSTER CWA
anodized aluminumaluminum shapes system
••
AZ-GRP-GR050-BA
P-GR050-PA
P-GR050-SD
P-GR050-BA
P-GR050-SS
B x H size assembly hole
B: -20mm H: -20mm X=52mm L=57mm
H (mm) 100 – 2000
B (mm) 300 – 4000Mini. height of the air intake H = 100 mmMax. size of the air intake H x B = 2000 mm x 6000 mm
62
ASSEMBLY DRAWING
Ventilation equipment
Centrum Klima – Products catalogue 79
Ventilation equipment
ROOF RECTANGULAR AIR INTAKE / EXHAUSTER TYPE A WDP-A
MATERIAL
galvanized steel•
H2
H1
H3
AxB
A1xB1
inlets are additionally protected with steel meshwe also produce elements in intermediate dimen-sions
••
PRODUCT CHARACTERISTICS
Tolerance ±5 mm
Size AxB (mm)
A1 (mm)
B1 (mm)
H1 (mm)
H2 (mm)
H3 (mm)
250x250 375 375 95 75 300
250x400 375 600 170 90 300
250x630 375 945 234 115 300
400x400 600 600 170 110 300
400x630 600 945 259 140 300
630x630 945 945 259 160 300
630x1000 945 1500 350 200 300
630x1600 945 2400 550 290 300
1000x1000 1500 1500 350 240 300
1000x1600 1500 2400 570 330 300
1200x1200 1800 1800 430 320 300
1200x1600 1800 2400 570 370 300
Centrum Klima – Products catalogue80
ROOF RECTANGULAR AIR INTAKE / EXHAUSTER TYPE B WDP-B
MATERIAL
galvanized steel•
HH
1
H2
20AxB
A xB1 1
side louvers of the air intake are made of steel shapes (LP66).inlets are additionally protected with steel meshwe also produce elements in intermediate sizes
•
••
PRODUCT CHARACTERISTICS
Tolerance ±5 mm
Ventilation equipment
Size AxB (mm)
A1 (mm)
B1 (mm)
H (mm)
H1 (mm)
H2 (mm)
250x250 340 340 520 300 35
250x400 340 490 580 300 35
250x630 340 720 635 300 60
400x400 490 490 640 300 35
400x630 490 720 695 300 60
630x630 720 720 725 300 60
630x1000 720 1090 815 300 90
630x1600 720 1690 940 300 105
1000x1000 1090 1090 870 300 90
1000x1600 1090 1690 995 300 105
1200x1200 1290 1290 990 300 100
1200x1600 1290 1690 1050 300 105
Centrum Klima – Products catalogue 81
Ventilation equipment
ROOF AIR INTAKE K
MATERIAL
galvanized steel• outlet additionally secured with perforated steel as standard manufactured with female coupling possible manufacturing with male coupling or with VKPK fl ange
•••
PRODUCT CHARACTERISTICS
Tolerance +5 mmØd – diameter of female coupling
Ød
h
h 1
ØD
Diameter Ød (mm)
Diameter ØD (mm)
h (mm)
h1 (mm)
Items Set Package Packaging
100 200 264 59 40 P2
125 225 267 52 36 P2
150 250 265 45 18 P2
160 260 270 45 18 P2
180 285 270 47 16 P2
200 315 273 49 15 P2
250 400 291 81 12 P1
315 500 303 90 9 P1
355 550 325 110 8 P1
400 600 344 131 5 P1
450 650 370 170 4 P1
500 700 400 210 4 P1
Centrum Klima – Products catalogue82
ROOF ROUND AIR INTAKE TYPE C CDO
MATERIAL
galvanized steel•
H2
H1
H
ØD
ØD1
Ø D Ø D1 (mm)
H (mm)
H1 (mm)
H2 (mm)
100 200 210 60 50
125 250 210 70 50
160 320 225 75 55
200 400 240 75 60
225 450 270 90 70
250 500 390 100 75
315 630 390 125 95
355 710 435 145 105
400 800 480 160 120
450 900 540 180 135
500 1000 600 200 150
560 1120 690 230 170
630 1260 750 250 190
710 1420 870 290 220
800 1600 960 320 240
900 1800 1080 360 270
1000 2000 1200 400 300
inlets are additionally protected with steel meshwe also produce elements in intermediate dimen-sionsbase is made on VKPK fl angepossible manufacturing with male coupling
••
••
PRODUCT CHARACTERISTICS
Ventilation equipment
Tolerance ØD1, H, H1 i H2: ±5 mm
Centrum Klima – Products catalogue 83
ROOF CIRCULAR AIR EXHAUSTER / INTAKE TYPE C WDO-C
MATERIAL
galvanized steel•
H1
H2
H
ØD
ØD2
ØD1
Ø D (mm)
Ø D1 (mm)
Ø D2 (mm)
H (mm)
H1 (mm)
H2 (mm)
100 125 200 175 50 50
125 156 250 220 50 50
160 200 320 260 55 60
200 250 400 340 60 60
225 280 450 380 70 70
250 312 500 425 75 75
315 393 630 530 95 100
355 446 710 600 105 110
400 500 800 680 120 120
450 560 900 765 135 135
500 625 1000 850 150 150
560 705 1120 960 170 170
630 786 1260 1070 190 190
710 893 1420 1220 220 220
800 1000 1600 1360 240 240
900 1125 1800 1530 270 270
1000 1250 2000 1700 300 300
used as an ending of ventilation systemsappropriate design protects the system from weather conditionsbase is made on VKPK fl angepossible manufacturing with male coupling
••
••
PRODUCT CHARACTERISTICS
Ventilation equipment
Centrum Klima – Products catalogue84
ROOF CIRCULAR AIR INTAKE / EXHAUSTER TYPE D WDO-D
MATERIAL
galvanized steel•
ØD
ØD1
H
Ø D (mm)
Ø D1 (mm)
H (mm)
200 250 600
250 325 750
315 410 945
355 460 1050
400 520 1200
450 580 1350
500 650 1500
560 730 1650
630 820 1890
710 930 2130
800 1040 2400
inlet is additionally protected with steel mesh with 12 x 12 mm openingsbase is made on VKPK fl angepossible manufacturing with male coupling
•
••
PRODUCT CHARACTERISTICS
Ventilation equipment
Tolerance D1, H: ±5 mm
Centrum Klima – Products catalogue 85
ROOF ROUND AIR INTAKE / EXHAUSTER HF/HN
MATERIAL
galvanized steel•
ØDL 1
H
ØA
siatkaocynkowana
Ø D (mm)
L1 (mm)
H (mm)
Ø A (mm)
pipe diameter (external) (mm)
100 115 345 180 14
125 115 360 225 14
140 115 400 240 18
150 115 430 260 18
160 115 460 280 18
180 115 495 310 18
200 115 525 345 18
225 115 565 375 18
250 115 610 410 20
280 115 660 470 20
300 115 715 530 20
315 115 740 550 20
355 115 810 600 24
400 115 1000 675 24
450 115 1070 770 24
500 115 1120 845 24
560 115 1125 965 24
600 115 1230 1070 24
630 115 1335 1175 24
710 115 1440 1255 24
800 115 1540 1340 24
inlet is additionally protected with steel mesh with 12 x 12 mm openingsHF - made with VKPK fl ange,HN - made with round branching. water drainage pipepossible manufacturing with male coupling
•
••••
PRODUCT CHARACTERISTICS
galvanized mesh
Ventilation equipment
Tolerance ØA, H, L1 ± 5 mm
HN
Centrum Klima – Products catalogue86
ROUND GRAVITY VENTILATOR WDC
MATERIAL
galvanized steel•
H
H1
D1
D
Ø D (mm)
Ø D1 (mm)
H (mm)
H1 (mm)
80 160 220 130
100 200 285 160
125 250 345 175
140 280 290 195
150 300 320 210
160 320 340 190
180 360 380 222
200 400 430 252
225 450 480 276
250 500 550 300
280 560 590 315
300 600 645 330
315 630 700 394
355 710 750 435
400 800 880 480
450 900 930 520
500 1000 1000 590
560 1120 1180 675
630 1260 1270 760
710 1420 1530 850
800 1600 1550 940
900 1800 1650 1070
1000 2000 1950 1200
made on VKPK fl angepossible manufacturing with male coupling
••
PRODUCT CHARACTERISTICS
Ventilation equipment
Centrum Klima – Products catalogue 87
ROOF BASE B-I, B-II, B-III PD
MATERIAL
galvanized steel•
H
B-I B-II
B-III
L
PJ
D
D
B
K
A
40
L
D
Ø D (mm)
H (mm)
A (mm)
K (mm)
Ø B (mm)
100 100 356 310 160
125 100 366 320 170
160 90 426 380 200
200 115 476 430 250
250 125 536 490 310
315 145 616 570 395
400 145 726 680 500
500 180 846 800 625
630 215 1006 960 785
800 265 1226 1180 1000
base is made on VKPK fl ange
PD-B III - manufactured with actuator driven damper.
•
PRODUCT CHARACTERISTICSL = 1000 mm B - II
L = 300 mm B - I
L = 1000 mm + PJ B - III
PJ - the size depends on the diameter of the damper
Ventilation equipment
Centrum Klima – Products catalogue88
RECTANGULAR ROOF BASE TYPE A PD-P
DESCRIPTION
dimension L depends on the roof structurestandard length L = 1000 mm
••
L
H
40
AxB
A3xB3
A2xB2
Dimension AxB (mm)
A2 (mm)
B2 (mm)
A3 (mm)
B3 (mm)
H (mm)
250x250 500 500 450 450 120
250x400 500 650 450 600 135
250x630 520 900 470 850 135
400x400 650 650 600 600 120
400x630 670 900 620 850 135
630x630 920 920 870 870 150
630x1000 950 1320 900 1270 170
630x1600 980 1950 930 1900 195
1000x1000 1350 1350 1300 1300 190
1000x1600 1380 1980 1330 1930 215
1200x1200 1550 1550 1500 1500 190
1200x1600 1580 1980 1530 1930 215
Ventilation equipment
Tolerance ±5 mm
Centrum Klima – Products catalogue 89
RECTANGULAR ROOF BASES PD-S
MATERIAL
galvanized steelattenuating mineral wool
••
F
H
E
D
G
gwint M
TYPE D (mm)
E(mm)
F (mm)
G (mm)
H (mm) thread
190/225 245 294 571 258 300 M6
310/311 330 395 657 345 300 M6
355/400 450 555 817 505 300 M10
450/499/500 535 625 877 565 300 M10
560/630 750 895 1147 835 300 M10
710 840 985 1300 925 300 M10
800/900 1050 1205 1540 1145 300 M10
PD-S roof bases are made of galvanized steel, which ensures their corrosion resistancethe bases are adapted to assemble of the following ventilators:
•
•
PRODUCT CHARACTERISTICS
thread M
DESIGN / USE
Roof bases serve as bearers for roof ventilators, air intakes or roof exhausters.
Systemair DVS DHS DVSI DVN DVNI DVC
Rosenberg DV DH DVS DVWN DVWNS DV-G
Ventilation equipment
Centrum Klima – Products catalogue90
RECTANGULAR ATTENUATING ROOF BASE PD-ST
MATERIAL
galvanized steelsound attenuating mineral wool
••
F
H
E
gwint M
H2
H1
G
TYPE D (mm)
E(mm)
F (mm)
H (mm)
H1 (mm)
H2 (mm) thread
190/225 245 294 571 600 150 150 M6
280/310 330 395 657 700 150 180 M6
355/400 450 555 817 900 200 250 M10
450/500 535 625 877 900 200 250 M10
560/630 750 895 1200 1070 200 250 M10
710 840 985 1300 1160 200 250 M10
800/900 1050 1205 1740 930 200 250 M10
attenuating roof base for roof ventilators is to be used in case of higher acoustic requirementssound attenuation with frequency of 250 HZ is 8 dB on the averagethe sound attenuating material is resistant to wear up to 20 m/sec.the bases are adapted to operate with the follow-ing ventilators:
•
•
•
•
PRODUCT CHARACTERISTICS
thread M
MARKINGSDimension L – basic version 600 mm. It is possi-ble to produce a straight connector of any length (dimension L) according to the customer’s needs.
Rosenberg DV DH DVS DVWN DVWNS DV-G
Ventilation equipment
DESIGN / USE
Roof bases serve as bearers for roof ventilators, air intakes or roof exhausters.
Centrum Klima – Products catalogue 91
ROUND DUCT FILTERS OFK
DESCRIPTION
OFK round duct fi lter is used for initial fi ltration of fl owing air in round duct systems. Filtering element is a EU4 class inset secured with a galvanized net. Cover is made from galvanized steel with gaskets on both ends. Construction ensures easy and fast assembly.
TYPE ØD (mm)
L (mm)
E (mm)
OFK 100 100 120 40
OFK 125 125 120 40
OFK 160 160 120 40
OFK 200 200 120 40
OFK 250 250 120 40
OFK 315 315 120 40
OFK 355 355 120 40
OFK 400 400 140 50
OFK 500 500 140 50
Ventilation equipment
ØD
LE E
Tolerance + 5 mm
Centrum Klima – Products catalogue92
CIRCULAR DUCT FILTERS FKO
DESCRIPTION
AxA
B
EØD
p (Pa)
150
100
50
00 1 2 3 4 5 6 7m/s
Prędkość przepływu
Stra
ta c
iśni
enia
Airflow speed
Pre
ssur
e lo
ss
Ventilation equipment
Duct filters are designed to be installed in round duct systems with standard diameters (100 – 400 mm). External cover is made of steel, assembly connector pipes have rubber gaskets and the filter cartridge (EU3 class) are based on a profiled steel net. The filter is used for initial filtration of the air intake.
TYPE A (mm)
B (mm)
ØD (mm)
E (mm)
FKO 100 180 180 100 40
FKO 125 180 180 125 40
FKO 140 180 180 140 40
FKO 150 210 180 150 40
FKO 160 210 180 160 40
FKO 180 250 180 180 40
FKO 200 250 180 200 40
FKO 225 300 180 225 40
FKO 250 300 180 250 70
FKO 300 360 180 300 70
FKO 315 360 180 315 70
FKO 355 410 180 355 70
FKO 400 460 180 400 70
FKO 450 510 180 450 70
Centrum Klima – Products catalogue 93
CASETTE FILTERS FS
DESIGN / USE
The drawer filter is used for initial air processing (fil-tering). The internal filter cartridge is made of EU3 class material and is based on galvanized mesh.
The filter is made of galvanized steel. The filter’s cover has a handle. It is possible to produce grawer duct filters within the dimensions given below:
H (mm) 200 – 1250
B (mm) 200 – 1250
Ventilation equipment
Blacha ocynk
B
G
H
Siatka 12 x 12 mm
Tkanina filtracyjna EU3
Ramka P20/P30
Rączka z blachy ocynk, mocowana na nity
G size according on the length side
Length (mm) ≤ 1000 > 1000
G (mm) 100 120
Border size P20 P30
Galvanized steel
12 x 12 mm mesh
Filtering fabric EU3
Galvanized steel handle fixed with rivets
Frame P20/P30
Centrum Klima – Products catalogue94
AI GRILLE (STEEL MESH) AI
H
B
25 mm
MATERIAL
galvanized steel•
steel mesh is fi xed with spot weldspulled steel wire mesh, openings 12 x 12 mmstandard frame width is 25 mm
It is possible to produce meshes with individually given dimensions.
•••
PRODUCT CHARACTERISTICS
H (mm) 300 – 2000
B (mm) 300 – 2000
Ventilation equipment
Centrum Klima – Products catalogue 95
RECTANGULAR FLEXIBLE DUCT CONNECTORS KEP
MATERIAL
flexible connector LEprofilecorner
•••
L A
A (mm)
B (mm)
L (mm)
160 160 155
200 160 155
200 200 155
250 160 155
250 200 155
250 250 155
315 160 155
315 200 155
315 250 155
315 315 155
400 160 155
400 200 155
400 250 155
400 315 155
400 400 155
500 200 155
Intermediate dimensions are available upon request.
A (mm)
B (mm)
L (mm)
500 250 155
500 315 155
500 400 155
500 500 155
630 250 155
630 315 155
630 400 155
630 500 155
630 630 155
800 315 155
800 400 155
800 500 155
800 630 155
800 800 155
1000 400 155
1000 500 155
A (mm)
B (mm)
L (mm)
1000 630 155
1000 800 155
1000 1000 155
1250 500 155
1250 630 155
1250 800 155
1250 1000 155
1250 1250 155
Ventilation equipment
USE
Flexible rectangular connectors are used in ventila-tion systems to eliminate vibrations transmitted by the devices.
They are also installed to compensate thermal elon-gations.
Centrum Klima – Products catalogue96
Flexible round connectors are used in ventilation systems to eliminate vibrations transmitted on the assembly by the devices.
MATERIAL USE
CIRCULAR FLEXIBLE CONNECTOR PIPES KEO-K
fl exible connector XEV-50 35/60/35, KEV-25 45/70/45, EEV-25 70/100/70VKPK fl angedimension L is depends on width of connector
•
••
Flexible connectors without VKPK fl ange
ØDp
ØD2L
ØD
n ØDo
D (mm)
Dp(mm)
D2(mm)
Do(mm)
Quantity of holes (n)
80 110 130 7 4
100 130 150 7 4
110 140 160 7 4
125 155 175 7 4
140 170 190 7 8
150 181 200 9 8
160 195 220 9 8
180 215 240 9 8
200 235 260 9 8
225 260 285 9 8
250 285 310 9 8
280 315 340 9 8
315 350 375 9 12
355 390 415 9 12
400 445 460 9 12
450 495 530 9 12
500 545 580 9 16
560 605 640 12 16
630 680 720 12 16
710 760 800 12 20
800 860 900 12 20
Ventilation equipment
Centrum Klima – Products catalogue 97
MATERIAL
PLENUM BOX SR
galvanized steel•
Ød
AxA
140
End cap
H
30
Size Grill size (mm) AxA (mm) H (mm) Ød (mm)
0 190 x 190 150 210 123
1 245 x 245 204 240 158
2 301 x 301 260 240 158
3 357 x 357 316 300 158
4 412 x 412 372 300 198
5 469 x 469 428 350 198
6 498 x 498 457 350 248
7 598 x 598 557 400 248
8 623 x 623 582 400 248
Box without a damper and insulation code: SRBox with a damper code: SR+PBox with insulation* code: SR+IBox with a damper and insulation* code: SR+I+P
* MST MATS - synthetic rubber foam
Upon request:Insulation Industrial Batts Black 80/15 Rockwool
PRODUCT CHARACTERISTICS
connections (spot embossments)built-in damper with SR+P mechanism individual size available upon request
•
Typical box dimensions:
Ventilation equipment
Centrum Klima – Products catalogue98
MATERIAL
PLENUM BOX
galvanized steel•
Air diffuser size (mm)
A x A (mm)
H (mm)
Ød (mm)
295 x 295 153 x 153 240 123
370 x 370 232 x 232 300 158
445 x 445 308 x 308 350 198
520 x 520 384 x 384 350 248
595 x 595 455 x 455 400 248
SR-HB40
Ød
AxA
140
End capH
30
Box without a damper and insulation code: SR-HB40Box with a damper code: SR-HB40+PBox with insulation* code: SR-HB40+IBox with a damper and insulation* code: SR-HB40+I+P
* MST MATS - synthetic rubber foam
Upon request:Insulation Industrial Batts Black 80/15 Rockwool
PRODUCT CHARACTERISTICS
connections (spot embossments)built-in damper with SR+P mechanismindividual size available upon request
•••
PLENUM BOX DEDICATED VORTEX DIFFUSER HB40.
HB40 plenum box
Ventilation equipment
Centrum Klima – Products catalogue 99
MATERIAL
PLENUM BOX SR-SD-B
galvanized steel•
AxA
140
End capCrossbar
with nut M6
A1xA1
H
30
Ød
40
Type diffuser
AxA (mm)
A1xA1 (mm)
H (mm)
Ød (mm)
SD-B 300 265 x 265 295 x 295 250 160
SD-B 400 347 x 347 377 x 377 300 200
SD-B 500 447 x 447 477 x 477 350 250
SD-B 600 540 x 540 570 x 570 400 250
Box without a damper and insulation code: SR-SD-BBox with a damper code: SR-SD-B+PBox with insulation* code: SR-SD-B+IBox with a damper and insulation* code: SR-SD-B+I+P
* MST MATS - synthetic rubber foam
Upon request:Insulation Industrial Batts Black 80/15 Rockwool
PRODUCT CHARACTERISTICS
connections (spot embossments)built-in damper with SR+P mechanism individual sizes available upon request
•
Typical box dimensions:
PLENUM BOX DEDICATED VORTEX DIFFUSER SD-B.
Ventilation equipment
Centrum Klima – Products catalogue100
MATERIAL
PLENUM BOX
galvanized steel•
SR-SD-C
Box without a damper and insulation code: SR-SD-CBox with a damper code: SR-SD-C+PBox with insulation* code: SR-SD-C+IBox with a damper and insulation* code: SR-SD-C+I+P
* MST MATS - synthetic rubber foam
Upon request:Insulation Industrial Batts Black 80/15 Rockwool
PRODUCT CHARACTERISTICS
connections (spot embossments)built-in damper with SR+P mechanism individual sizes available upon request
•
PLENUM BOX DEDICATED VORTEX DIFFUSER SD-C.
AxA
140
End capCrossbar
with nut M6
A1xA1
H
30
Ød
40
Diffusertype
AxA (mm)
A1xA1 (mm)
H (mm)
Ød (mm)
SD-C 300 285 x 285 315 x 315 250 160
SD-C 400 367 x 367 397 x 397 300 200
SD-C 500 455 x 455 485 x 485 300 200
SD-C 60024 slots 560 x 560 590 x 590 320 250
SD-C 60048 slots 580 x 580 590 x 590 320 250
Typical box sizes:
Ventilation equipment
Centrum Klima – Products catalogue 101
DESCRIPTION
ROUND CONNECTION DSP
made of galvanized steelenables fast and easy installation of the DS air valve in the ceilingallows for connection of the air valve with ventila-tion and air conditioning systems
••
•
A
H1
D
Air outlet size (mm)
D connection size (mm)
H1 connection size (mm)
Size of the base A (mm)
160 159 140 257
200 199 140 307
250 249 140 357
300 315 140 407
350 349 140 457
Ventilation equipment
Centrum Klima – Products catalogue102
DESCRIPTION
CHIMNEY ROOT CENTROWENT
Rotary chimney cowl Centrowent is a device, which in a dynamic way, uses force of the wind to increase chimney draught. The turbine always rotates in the same direction no matter for the wind strength or its direction. It is to be mounted on gravitation based ventilation chimney duct endings.
CA / CN
CHARACTERISTICS
no corrosion – collar made of zinc-plated steellight weight – aluminum or stainless steel fan rotorquiet operation – rotor bearingseasy cleaning – rotor fi xed to axle with screwlogistics – each extension in separate boxCA - rotor made of aluminumCN - rotor and fl ange made of stainless steel
••
•••••
Ventilation equipment
D1
D
H
Version of the base
Centrum Klima – Products catalogue 103
Ventilation equipment
Chimney root, coupling
Diameter (mm) Ø130 Ø150 Ø160 Ø200 Ø250 Ø300 Ø315 Ø400 Ø450 Ø500
D (mm) 130 150 160 200 250 300 315 400 450 500
H (mm) 193 217 222 283 365 412 433 540 540 650
D1 (mm) 195 225 240 300 360 430 452 550 610 675
Chimney root, coupling, split
Diameter (mm) Ø130 Ø150 Ø160 Ø200 Ø250 Ø300 Ø315 Ø400 Ø450 Ø500
D (mm) 130 150 160 200 250 300 315 400 450 500
H (mm) 313 337 342 409 475 532 553 640 660 720
D1 (mm) 195 225 240 300 360 430 452 550 610 675
Chimney root with flange
Diameter (mm) Ø130 Ø150 Ø160 Ø200 Ø250 Ø300 Ø315 Ø400 Ø450 Ø500
D (mm) 130 150 160 200 250 300 315 400 450 500
d (mm) 190 210 220 260 310 360 375 460 510 560
H (mm) 193 217 222 283 365 412 433 540 540 650
D1 (mm) 195 225 240 300 360 430 452 550 610 675
Chimney root with base
Diameter (mm) Ø130 Ø150 Ø160 Ø200 Ø250 Ø300 Ø315 Ø400 Ø450 Ø500
D (mm) 130 150 160 200 250 300 315 400 450 500
A (mm) 333 333 333 333 390 440 460 540 590 640
H (mm) 193 217 222 283 365 412 433 540 540 650
D1 (mm) 195 225 240 300 360 430 452 550 610 675
Centrum Klima – Products catalogue104
Ventilation equipment
DESCRIPTION
CHIMNEY ROOTS ROTOFLEX
Rotating Chimney Root Rotofl ex is designed for supporting the air exhaustion in chimneys in smoke or fume ducts by creating underpressure. Roots top is always pointing the wind direction.
RTN
CHARACTERISTICS
RTN - rotor and fl ange made of stainless steel No corrosion - collar made of zinc-plated steelQuiet operation - rotor bearingsLogistics - each extension in separate box
•••
Chimney root, coupling, split
Diameter (mm) Ø130 Ø150 Ø180 Ø200 Ø250 Ø300 Ø350
D (mm) 130 150 180 200 250 300 350
H (mm) 438 486 579 604 672 787 880
L (mm) 150 173 208 231 263 316 364
“PŁETWA” VERSION
Centrum Klima – Products catalogue 105
Ventilation equipment
Chimney root with flange
Diameter (mm) Ø130 Ø150 Ø180 Ø200 Ø250 Ø300 Ø350
D (mm) 130 150 180 200 250 300 350
d (mm) 190 210 240 260 310 360 410
H (mm) 350 406 499 524 592 707 800
L (mm) 150 173 208 231 263 316 364
Chimney root with base
Diameter (mm) Ø130 Ø150 Ø180 Ø200 Ø250 Ø300 Ø350
D (mm) 130 150 180 200 250 300 350
A (mm) 333 333 333 333 333 390 450
H (mm) 350 406 499 524 592 707 800
L (mm) 150 173 208 231 263 316 364
Chimney root, coupling, split
Diameter (mm) Ø130 Ø150 Ø180 Ø200 Ø250 Ø300 Ø350
D (mm) 130 150 180 200 250 300 350
H (mm) 516 576 607 724 822 967 1090
L (mm) 172 179 230 264 305 366 422
“KOGUT” VERSION
Chimney root with flange
Diameter (mm) Ø130 Ø150 Ø180 Ø200 Ø250 Ø300 Ø350
D (mm) 130 150 180 200 250 300 350
d (mm) 190 210 240 260 310 360 410
H (mm) 438 496 607 724 644 896 1010
L (mm) 172 179 230 264 305 366 422
Chimney root with base
Diameter (mm) Ø130 Ø150 Ø180 Ø200 Ø250 Ø300 Ø350
D (mm) 130 150 180 200 250 300 350
A (mm) 333 333 333 333 333 390 450
H (mm) 438 496 607 724 644 896 1010
L (mm) 172 179 230 264 305 366 422
Centrum Klima – Products catalogue106
Ventilation equipment
CHIMNEY VH
PRODUCT CHARACTERISTICS
manufactured with male coupling (possible manufacturing with female coupling) inlet is protected with steel mesh with 12 x 12 mm openings
•
•
galvanized steel•
MATERIAL
ØD
Ød
HØ d (mm) Ø D (mm) H (mm)
80 180 175
100 180 175
125 225 180
140 290 190
150 290 190
160 290 190
180 360 240
200 360 240
225 405 245
250 450 250
280 570 265
300 570 265
315 570 265
355 720 345
400 720 355
450 810 370
500 900 430
560 1080 485
600 1080 485
630 1135 495
710 1280 510
800 1440 535
Centrum Klima – Products catalogue 107
L 60
ØD
ØD1
The external cover is made of a spirally coiled pipe. The attenuating layer is made of mineral wool and is separated from the duct system with fi bre wire cloth and perforated galvanized steel.
USE
DESIGN
ROUND ACOUSTIC SILENCERS
Round silencers are designed to suppress the noise in duct ventilation and HVAC systems.
ØD1 (mm)ØD (mm)
Isolation 50 mm Isolation 100 mm
80 180 300
100 200 315
125 225 315
140 250 355
150 250 355
160 250 355
180 280 400
200 315 400
225 315 400
250 355 450
TAO
Standard silencer lengths:L = 600, 900, 1000, 1200 (mm)
Silencers
ØD1 (mm)ØD (mm)
Isolation 50 mm Isolation 100 mm
280 400 500
315 400 500
355 450 560
400 500 630
450 560 630
500 630 710
560 630 800
630 710 800
710 800 900
800 900 1000
Centrum Klima – Products catalogue108
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 100/50/1200 7 11 23 42 49 50 50 36
TAO 100/50/1000 5 10 18 32 48 50 50 30
TAO 100/50/900 5 10 17 31 43 50 47 28
TAO 100/50/600 5 8 12 23 35 48 40 210
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 100/50/1200 TAO 100/50/1000
TAO 100/50/900 TAO 100/50/600
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 125/50/1200 4 9 18 33 47 50 49 26
TAO 125/50/1000 3 7 15 26 45 50 45 22
TAO 125/50/900 3 7 14 20 40 50 42 20
TAO 125/50/600 2 4 9 19 33 43 35 130
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 125/50/1200 TAO 125/50/1000
TAO 125/50/900 TAO 125/50/600
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 160/50/1200 4 7 14 26 40 45 34 16
TAO 160/50/1000 3 6 12 20 37 43 29 13
TAO 160/50/900 3 5 11 19 34 40 26 12
TAO 160/50/600 2 4 7 15 28 34 17 80
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 160/50/1200 TAO 160/50/1000
TAO 160/50/900 TAO 160/50/600
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 200/50/1200 2 5 12 22 38 35 23 12
TAO 200/50/1000 2 4 10 18 32 33 21 11
TAO 200/50/900 3 4 9 18 31 30 20 11
TAO 200/50/600 1 3 7 14 25 23 16 100
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 200/50/1200 TAO 200/50/1000
TAO 200/50/900 TAO 200/50/600
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 250/50/1200 1 3 10 21 33 26 17 9
TAO 250/50/1000 1 3 8 17 27 22 14 7
TAO 250/50/900 1 3 7 16 24 20 12 6
TAO 250/50/600 1 2 5 12 16 13 8 40
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 250/50/1200 TAO 250/50/1000
TAO 250/50/900 TAO 250/50/600
Silencers
Centrum Klima – Products catalogue 109
Silencers
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 315/50/1200 1 3 8 17 27 21 11 6
TAO 315/50/1000 1 2 6 16 22 17 9 5
TAO 315/50/900 1 2 6 15 20 15 8 5
TAO 315/50/600 0 1 4 11 14 10 5 3
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 315/100/1200 3 8 19 32 34 19 5 1
TAO 315/100/1000 2 7 16 27 31 16 4 1
TAO 315/100/900 2 6 14 24 28 14 4 1
TAO 315/100/600 1 4 10 16 19 9 3 10
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 315/100/1200 TAO 315/100/1000TAO 315/100/900 TAO 315/100/600
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 400/50/1200 0 2 6 15 22 7 7 4
TAO 400/50/1000 0 2 5 14 19 6 5 3
TAO 400/50/900 0 1 5 13 17 6 5 3
TAO 400/50/600 0 1 3 10 12 5 3 1 0
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 400/50/1200 TAO 400/50/1000
TAO 400/50/900 TAO 400/50/600
TypeAttenuation [dB]
63 125 250 500 1000 2000 4000 8000
TAO 400/100/1200 3 6 15 27 23 8 5 3
TAO 400/100/1000 3 5 13 23 19 7 4 3
TAO 400/100/900 3 4 12 21 17 6 4 2
TAO 400/100/600 2 3 8 16 11 5 3 10
10
20
30
40
50
60
63 125 250 500 1000 2000 4000 8000[Hz]
[dB]
TAO 400/100/1200 TAO 400/100/1000TAO 400/100/900 TAO 400/100/600
63 125 250 500 1000 2000 4000 8000
TAO 315/50/1200 TAO 315/50/1000TAO 315/50/900 TAO 315/50/600
[dB]
[Hz]
0
10
20
30
40
50
60
Centrum Klima – Products catalogue110
TypeTotal pressure loss [Pa]
Total pressure loss coefficient2
[m/s]4
[m/s]6
[m/s]8
[m/s]10
[m/s]
TAO 100/50/1200 1 4 8 15 23 0,39
TAO 100/50/1000 1 3 7 12 19 0,32
TAO 100/50/900 1 3 6 11 17 0,29
TAO 100/50/600 0 2 4 7 12 0,19
0
5
10
15
20
25
2 4 6 8 10[m/s]
[Pa]
TAO 100/50/1200 TAO 100/50/1000
TAO 100/50/900 TAO 100/50/600
TypeTotal pressure loss [Pa]
Total pressure loss coefficient2
[m/s]4
[m/s]6
[m/s]8
[m/s]10
[m/s]
TAO 125/50/1200 1 3 6 11 18 0,29
TAO 125/50/1000 1 2 5 9 15 0,24
TAO 125/50/900 1 2 5 8 13 0,22
TAO 125/50/600 0 1 3 6 9 0,15
0
5
10
15
20
25
2 4 6 8 10[m/s]
[Pa]
TAO 125/50/1200 TAO 125/50/1000
TAO 125/50/900 TAO 125/50/600
TypeTotal pressure loss [Pa]
Total pressure loss coefficient2
[m/s]4
[m/s]6
[m/s]8
[m/s]10
[m/s]
TAO 160/50/1200 1 2 5 8 13 0,22
TAO 160/50/1000 0 2 4 7 11 0,18
TAO 160/50/900 0 2 3 6 10 0,16
TAO 160/50/600 0 1 2 4 6 0,110
5
10
15
20
25
2 4 6 8 10[m/s]
[Pa]
TAO 160/50/1200 TAO 160/50/1000
TAO 160/50/900 TAO 160/50/600
TypeTotal pressure loss [Pa]
Total pressure loss coefficient2
[m/s]4
[m/s]6
[m/s]8
[m/s]10
[m/s]
TAO 200/50/1200 0 2 4 6 10 0,16
TAO 200/50/1000 0 1 3 5 8 0,14
TAO 200/50/900 0 1 3 5 7 0,12
TAO 200/50/600 0 1 2 3 5 0,08
0
5
10
15
20
25
2 4 6 8 10[m/s]
[Pa]
TAO 200/50/1200 TAO 200/50/1000
TAO 200/50/900 TAO 200/50/600
TypeTotal pressure loss [Pa]
Total pressure loss coefficient2
[m/s]4
[m/s]6
[m/s]8
[m/s]10
[m/s]
TAO 250/50/1200 0 1 3 5 7 0,12
TAO 250/50/1000 0 1 2 4 6 0,10
TAO 250/50/900 0 1 2 4 6 0,09
TAO 250/50/600 0 1 1 2 4 0,060
5
10
15
20
25
2 4 6 8 10[m/s]
[Pa]
TAO 250/50/1200 TAO 250/50/1000
TAO 250/50/900 TAO 250/50/600
Silencers
Centrum Klima – Products catalogue 111
Silencers
TypeTotal pressure loss [Pa]
Total pressure loss coefficient2
[m/s]4
[m/s]6
[m/s]8
[m/s]10
[m/s]
TAO 315/50/1200 0 1 2 4 6 0,09
TAO 315/50/1000 0 1 2 3 5 0,08
TAO 315/50/900 0 1 1 3 4 0,07
TAO 315/50/600 0 0 1 2 3 0,05
0
5
10
15
20
25
2 4 6 8 10[m/s]
[Pa]
TAO 315/50/1200 TAO 315/50/1000
TAO 315/50/900 TAO 315/50/600
TypeTotal pressure loss [Pa]
Total pressure loss coefficient2
[m/s]4
[m/s]6
[m/s]8
[m/s]10
[m/s]
TAO 400/50/1200 0 1 1 3 4 0,07
TAO 400/50/1000 0 1 1 2 3 0,06
TAO 400/50/900 0 0 1 2 3 0,05
TAO 400/50/600 0 0 1 1 2 0,03
0
5
10
15
20
25
2 4 6 8 10[m/s]
[Pa]
TAO 400/50/1200 TAO 400/50/1000
TAO 400/50/900 TAO 400/50/600
Centrum Klima – Products catalogue112
FLEXIBLE ROUND SILENCERS TAO S-FLEX
USE
Round acoustic attenuators are designed to suppress noise in ventilation and air conditioning duct systems.
DESIGN
External cover made of semi-flexible aluminum duct S-Flex®. Damping layer of mineral wool secured with perforated aluminum duct.
L 60
ØD
ØD1
Standard attenuator lengths:L = 600, 900, 1000, 1200, 1500 [mm]
ØD1 (mm)ØD (mm)
Isolation 50 mm Isolation 100 mm
80 180 315
100 200 315
120 250 315
125 250 315
130 250 315
150 250 315
160 250 400
180 315 400
200 315 400
250 400 -
315 400 -
Silencers
Centrum Klima – Products catalogue 113
Silencers
RECTANGULAR ACOUSTIC SILENCERS TAP
H
S/2D S
B
L
B (mm) 150-200 300-400 450-600 750-800 900-1000 1050-1200 1350-1400 1500-1600
H (mm) Quantity walls
300
4501 2 3 4 5 6 7 8
600
900
USE
Panel sound silencers are used to suppress the noi-se in duct ventilation and HVAC systems
The external cover is made of galvanized steel. Con-necting fl anges are made of DW duct shapes and H corners. Thanks to that, the silencer is rigid enough and can be easily installed in a duct system. DW20 shapes are used for side dimensions up to 1000 mm while for larger dimensions DW30 shapes are used. Slotted lever frames are made of galvanized steel and are fi lled with sound attenuating material - mineral wool. The fi bre wire cloth, which tightly covers the external side of the slotted levers, prevents the mineral wool from penetrating into the duct system. The use of high quality attenuating materials and correct assembly of the product ensure high attenuation levels.
DESIGN
D (mm) 100, 200
S (mm) 100
ASSEMBLY DRAWING
1. Sound attenuating panels are covered with fibre wire clothon both sides
2. internal panels of the silencer (slotted levers),3. cover
It is possible to produce meshes with individually given sizes.
STANDARD SILENCER LENGTHS L= 600, 1000, 1200, 1500 mm
Centrum Klima – Products catalogue114
50
0,3
0,40,50,6
0,8
1,01,0
1,5
2,0
3,0
4,0
5,06,0
8,0
10
15
20
30
40
50
60
80
100
15 20 30 40 50 100 150 200 300 400 500 1000 1500 2000 5000l/s
m /h3
Wydatek powietrza q
Stra
ta c
iśni
enia
Pa/
m
Śr. n
omin
alna
[mm
]
100 200 300 500 1000 2000 5000 10000 18000
630
550
500
450
400
35528020016012580
315250180140100
Pręd
kość
m/s
3,0
3,5
4,0
5,0
6,0
7,0
8,0
10
15
FLEXIBLE ACOUSTIC SILENCER TAE
TYPE TAE
Diameter range 83-508 mm
Operating temperature range -30/+140 °C
Maximum air speed 30 m/s
Maximum operating pressure 2500 Pa
Standard length 1 m
Cardboard package 0.5 m
standard 1 m long silencers sacked into 0.5 m card-board boxeslow transportation and storage costeasy assembly no need to use special tools for cutting or fi xingdoes not produce toxic gases in high temperatures
•
••••
USEPRODUCT ADVANTAGES
The fl exible silencer is designed to be used in duct AC and ventilation systems. Attenuates noise and system vibrations. Reduces the need to use fi ttings.
DESIGN
The external cover is made of multi layer perfo-rated flexible aluminum duct. The silencer is in-sulated with 25 mm thick mineral wool layer with density of 20 kg/m³. The external layer is made of alu-minum-Polyester laminate reinforced with fi bre wire. The product has properly prepared endings which make its assembly in a duct system easier.The silencer is installed with fi xing clips.
Linear resistance graph
Pres
sure
loss
Pa/
m
Air volume q
Nom
inal
dia
met
er (m
m)
25
20
15
10
5
063 125 250 500 1000 2000 4000 8000
Tłumik długości 1 metra
częstotliwość (Hz)
Tłum
ieni
e dB
(A)
1 meter long silencer
Frequency Hz
Atte
nuat
ion
dB (A
)
Silencers
Centrum Klima – Products catalogue 115
PIPE CLIPS FOR ROUND DUCTS OPO/OPOX OPO INOX/OPOX INOX
USE
Pipe clips are used to hang round duct networks (SPIRO type or B I). It ensures fast assembly thanks to an easy system of locking and tightening. Version with a gasket prevents the transmission of vibrations from the system to the building’s structure. The acid resistant steel version may be used in systems with higher anti corrosion requirements.
Nominal diameter D
(mm) Pcs./box Nut
80 60 M8/M10100 60 M8/M10125 60 M8/M10150 60 M8/M10160 60 M8/M10180 30 M8/M10200 60/30 M8/M10225 30 M8/M10
shaped galvanized steel or acid resistant steelavailable with EPDM rubber shock absorber which Prevents the transmission of vibrations (OPOX)supplied with M8 or M10 nut which serves as the threaded bar handle (Ø80 - Ø400)on request it is available in acid resistant version (INOX).
••
•
•
DESIGN
Nominal diameter D
(mm) Pcs./box Nut
250 30 M8/M10280 30 M8/M10300 20 M8/M10315 30 M8/M10355 20 M8/M10400 20 M8/M10450 10 -500 10 -
Nominal diameter D
(mm) Pcs./box Nut
560 10 -630 10 -710 10 -800 10 -900 Z -
1000 Z -1120 Z -1250 Z -
Assembly accessories
A
R
Detail A (2:1)10
20
2
9
M10
M6x20
M8
ø13,4
19,5
M8 and M10 thread according ISO-metricMaximal load: 8000NMaximal torque: 20Nm
B
Section Rubber
A
23
20
M6x20R(without rubber)
20
9
B
M10M8
M8 and M10 thread according ISO-metricMaximal load: 8000NMaximal torque: 20Nm
Detail A (2:1)
10
ø13,4
19,5
3
24,5
11,5
R
ø11
3
3
25
Section Rubber
R
24,5
11,5
ø11
OPO Ø80 - Ø400 OPO Ø450 - Ø1250
OPOX Ø80 - Ø400 OPOX Ø450 - Ø1250
Centrum Klima – Products catalogue116
DESIGN/USE
METAL BAND CLIP CM
CM metal band clips are made of 9 mm wide stain-less steel tape. Their properly shaped edges prevent damaging the ducts during assembly. May be used with any type of fl exible ducts. The band clip is in-stalled with a special, fast opening and closing CMC fastener.
D
Size range (mm) Items/box
CM 60 – 110 50
CM 60 – 135 50
CM 60 – 165 50
CM 60 – 215 50
CM 60 – 270 50
CM 60 – 325 50
Assembly accessories
Centrum Klima – Products catalogue 117
CMC fasteners are used to make clip bands on any diameter duct using CMB tape. This solution helps you to avoid the need for having many diameter bands in your warehouse. Special design of the CMC fastener allows for quick locking or unlocking, which makes assembly of the band on a duct a lot easier.
Box – 50 pcs.
DESIGN/USE CLIP FASTENER FOR CMC BANDS
METAL CLIP TAPE
CMB is a 9 mm wide stainless steel tape. It is rolled and 30 meters long. Its properly shaped edges prevent damaging the ducts during assembly. The tape is unrolled from handy plastic packages. It enables the user to install a clip band on any di-ameter thanks to the CMC fastener. The rolled CMB metal tape is an economic, convenient and fast way to create clip bands. The details of the band are described on the package.
Box – 50 pcs.
TYPE CMB
Material stainless steel
Width 9 mm
Roll box 30 m
CMB / CMC
Assembly accessories
Centrum Klima – Products catalogue118
DESIGN/USE
NYLON BAND CLIP CMN
CMN nylon band clips are an economic alternative for metal bands when installing fl exible ducts. Thanks to their design and easy use, they are easy to install, make the work much faster and hold the duct securely on the connector pipe. Nylon bands can be used within the temperature range: - 55°C to + 100°C. They are available in lengths ranging from 550 mm to 1188 mm. If other lengths are required, the bands can be easily connected without using any tools. To tighten the nylon bands securely, it is recommended to use DIT-2 clamp.
Box – 100 pcs.
Maximum length (mm)
550 800 920 1188
Assembly accessories
Centrum Klima – Products catalogue 119
Assembly accessories
DESCRIPTION
SUPRESSING BANDS
Supressing bands for fan installation in round ducts.
Type Diameter[mm]
OM 100 100
OM 125 125
OM 150 150
OM 160 160
OM 200 200
OM 250 250
OM 315 315
OM 355 355
OM 400 400
OM 500 500
OM
Centrum Klima – Products catalogue120
ASSEMBLY PROFILE – GALVANIZED
14 mm
22 mm
14 mm
14 mm
14 mm
W 105 PROFILE
W 2 PROFILE
W 106 PROFILE
W 107 PROFILE
W 41 PROFILE
Metal thickness: 2,0 mmSize: 20x35 mmLength: 2 m, 5 mWeight: 1,08 kg/m
Metal thickness: 1,5 mmSize: 20x30 mmLength: 2 m, 5 mWeight: 0,87 kg/m
Metal thickness: 1,7 mmSize: 30x30 mmLength: 2 m, 5 mWeight: 1,34 kg/m
Metal thickness: 1,7 mmSize: 43x30 mmLength: 2 m, 5 mWeight: 1,71 kg/m
Metal thickness: 2,5 mmSize: 41x41 mmLength: 5 mWeight: 2,67 kg/m
50
30
5
11 43 ±0,5
30 +0,5
14 +1 ==
50
30
5
1130 20 ±0,5
35 +0,5
14 +1 ==
50
30
5
11 20 ±0,5
30 +0,5
14 +1 ==
1450
30
5
11 30 ±0,5
30 +0,5
14 +1 ==
35
20
11
22 ±0,5
41 ±0,5
41 +0,5
Assembly accessories
Centrum Klima – Products catalogue 121
Assembly accessories
Z SUSPENSION PROFILE WITH SHOCK ABSORBING RUBBER
DESCRIPTION
For assembly of rectangular ventilation ducts with the use of M8 and M10 threaded bars and self-drilling screws. Material –2 mm thick steel tape.Material – stainless steel tape.The rubber shock absorber prevents the transmis-sion of vibrations from the system to the building’s structure.Box – 100 pcs.
16
6 x Ø4,5
35
35
30Ø15
60
thickness sheet 2 mm
9
6 x Ø4,5
35
30Ø15
95
gr. blachy 2 mm
L SUSPENSION PROFILE WITH SHOCK ABSORBING RUBBER
DESCRIPTION
For assembly of rectangular ventilation ducts with the use of M8 and M10 threaded bars and self-drilling screws. Material – 2 mm thick steel tape. Material – stainless steel tape.The rubber shock absorber prevents the transmission of vibrations from the system to the building’s structure.Box – 100 pcs.
thickness sheet 2mm
Centrum Klima – Products catalogue122
SCREWED BAR HANDLE
Type B (mm) C (mm) D (mm) M (mm)Maximum
load (kg)
DWK - M6 48 42 M6 10 112
DWK - M8 38 35 M8 10 112
DWK - M10 45 42 M10 10 245
M D
C
B
NS
Material – steel tape. Material – stainless steel M8, M10. 50 pcs.
VENTILATION DUCT CLIP
B
A
C
DESCRIPTION
A = 32 mm; B = 19 mm; C = 13 mmM8x25mm screw DW 40 and other systems.Thickness - 2,5 and 3 mmMaterial – steel tape. Material – 2,5 mm thick stainless steel tape. 500 pcs.
R / V SUSPENSION PROFILE WITH SHOCK ABSORBING RUBBER
DESCRIPTION
For assembly of round ventillation ducts with the use of M8 and M10 threaded bars and self-drilling screws. Material – 2 mm thick steel tape. Material – stainless steel tape. The rubber shock absorber prevents the transmission of vibrations from the system to the building’s structure.Box – 100 pcs.
TYPE V
TYPE R
105
45°
20 Ø8,5
Ø6,5
30
50
50
45° 30
zawiesie typu R(blacha trapezowa)
zawiesie typu L zawiesie typu Z
Hanger round channel Hanger rectangular channel
thickness sheet 2 mm
thickness sheet 2 mm
suspension L suspension Z
trapezodialscheet
Assembly accessories
Centrum Klima – Products catalogue 123
Assembly accessories
SCREWED BAR
ANCHOR BUSH
SHOCK ABSORBING RUBBER RU-25
DESCRIPTION
M 6M 8M 10– length 2 m– galvanized
DESCRIPTION
dividable galvanized steel M 6 x 24 mmM 8 x 30 mmM10 x 40 mm
spreading brass sleeveM8 x 27
•
•
DESCRIPTION
For assembly shape of W 2, W 105, W 106 and W 107 systems.
EP 27
M 8M 10– length 2 m– stainless steel
Centrum Klima – Products catalogue124
DOUBLE SCREWED THREAD SCREW VDF
DESCRIPTION
For direct assembly of suspension profi les on the walls and ceilings.Material – galvanized steel
SELF-DRILLING METAL SHEET SCREWS
DESCRIPTION
For quick assembly of suspension profi les, metal sheet connections and connecting shapes in ventilation systems. Hexagonal head 7 mmGalvanized steel - 4,2 x 13 mm; 4,2 x 16 mm; 4,2 x 25 mm; 4,8 x 16 mm;Stainless steel - 4,2 x 13 mm; 4,2 x 16 mm;1000 pcs.
SELF-DRILLING METAL SHEET SCREWS PAN-HEAD
DESCRIPTION
For quick assembly of suspension profi les, metal sheet connections and connecting shapes in ventilation systems. Rectangular hole in round head4,2 x 13 mm; 4,2 x 16 mm; 4,2 x 25 mm; 4,2 x 42 mm1000 pcs.
Assembly accessories
Centrum Klima – Products catalogue 125
Assembly accessories
SUSPENSION PROFILE TO AKERMAN CEILINGS
DESCRIPTION
Galvanized- for assembly in suspended ceilingsThread – M8Total length – 125 mmThread length – 85 mm
TERMINAL DCC-14 SHEET METAL SCREWS
DESCRIPTION
The magnetic tip can be used as a socket wrench together with an automatic screwdriver for hexagonal head 7 mm sheet metal screws. Size 7 mm
PAN-HEAD
VERGACOL VG TIGHTENING MASS
DESCRIPTION
Special tightening mass for seams, connections of steel elements and repair works. Thick mass in zinc-like colour which remains elastic after hardening.
310 ml packagetightens and connects metal surfaces (steel, galva-nized metals, aluminum, stainless steel, etc.)adhesion force after 5 days - minimum 25 kg/cm²resistant to temperatures from -30°C to +120°Cresistant to most chemical substancesstable adhesion to metal surfaces after hardening
Box - 24 pcs
••
••••
Centrum Klima – Products catalogue126
ZINC SPRAY ALUCYNK ALZN 600
APPLICATION
permanent protection of metal surfaces from corrosion spotting of damaged galvanized elements repair of cut, heat sealed and welded elements applying corrections following galvanization, heat sealing and welding.
••••
ADVANTAGES
phigh zinc and aluminium content 99% excellent resistance to abrasion excellent covering power highly effi cient and economical resistant to high temperatures short drying time
••••••
PROPERTIES
drying time - the surface is resistant to touching after 2-3 minutes, complete drying time 30 minproduced using acrylic resins silver colour
•
••
INDICATIONS ON PROCESSING
clean up and remove fats from the surface to be painted remove remains of rust through rubbing down remove old varnish coatings mix the product thoroughly by shaking it for ca. 1 minute
•
•••
ACETIC SILICONE
DESCRIPTION
Single-component non-shrinkable silicone sealant char-acterized by high elasticity, setting with air moisture, resistance to changing weather conditions and UV ra-diation.
Box - 15 pcs.
Packaging - 500 ml, 12pcs./box
Assembly accessories
Centrum Klima – Products catalogue 127
Assembly accessories
ACRYLIC SILICONE
DESCRIPTION
Dispersive, water-thinnable acrylic tightening mass, which provides plastic-fl exible easy to paint welds after hardening. Resistant to weather conditions, to be used both outdoors and indoors. Very adhesive to most materials.– 310 ml package– resistant to temperatures from -30°C to +80°C– to be used in temperatures from +5°C to +35°C– can be painted after 24h– attested by Polish National Institute of Hygiene (PZH), technical approval of Building Research Institute (ITB)
Box - 15 pcs.
PE ASSEMBLY FOAM
DESCRIPTION
Single component polyurethane foam is designed for assembly, tightening and attenuation. It is characterized by good adhesion to most materials.Hardened foam is resistant to high and low temperatures.
750 ml packageyellowstructure after hardening dense foam with even and fi necellular structure similar to solid materials operating ground temperature from 0°Cthermal resistance from -50°C to +90°Ccombustibility B3 (DIN4102)skin formation time 10-14 mincomplete hardening time 24hattested by Polish National Institute of Hygiene (PZH), technical approval of Building Research Institute (ITB)
Box - 12 pcs
•••••••••••
Centrum Klima – Products catalogue128
NN GALVANIZED NUT
Type Thread Pack. (pcs.)
Weight (kg)
NN06 M6 4000 8
NN08 M8 2000 9
NN10 M10 1500 15
LN CONNECTING NUT
Type Description
LN630 M6, lenght 30 mm
LN830 M8, lenght 30 mm
LN1030 M10, lenght 30 mm
NK STAINLESS STEEL NUT
Type Thread Pack. (pcs.)
NK08 M8 2000
BB GALVANIZED SCREW
Type Size Pack. (pcs.) Weight (kg)
BB0625 M6x25 500 3,5
BB0825 M8x25 300 3,75
BB1025 M10x25 200 4
Assembly accessories
Centrum Klima – Products catalogue 129
Assembly accessories
BK STAINLESS STEEL SCREW
Type Description Pack. (pcs.)
BK0825 M8x25 300
WW ENLARGED GALVANIZED WASHER
Type Size Pack. (pcs.) Weight (kg)
WW06 M6 4000 14
WW08 M8 4000 28
WW10 M10 3000 19
PES GASKET
DESCRIPTION
For tightening rectangular ventilation ducts.Material – polyethylene foam with closed cells, physical reticulation. Dark grey. Operating Temperature Range: -80°C … +110°CBreadth 10 mm x thickness 4 mm, package 100 mBreadth 15 mm x thickness 4 mm, package 60 mBreadth 40 mm x thickness 4 mm, package 20 mBreadth 12 mm x thickness 6 mm, package 50 m Breadth 10 mm x thickness 7 mm, package 50 m
Centrum Klima – Products catalogue130
TEMPERATURE RESISTANT GASKETS PEST
DESCRIPTION
The gasket is made from ceramic fi ber which ensures its hight tempertaure resitance as well as lack of any fumes by contact with fi re.Glue placed on one side of the gasket ensures easy assembly.Gasket is a perfect choice for ventilation ducts with high fi re and smoke safety requirements.
Width 10 mm x thickness 4 mm, package 10 m.Width 10 mm x thickness 5 mm, package 10 m.Width 10 mm x thickness 6 mm, package 10 m.
Adhesive acrylic dispersion, solvent-free
Adhesive carrier nonwoven web
Liner siliconized PE-foil
Colour white
Density 200 - 300 kg/m3
Fiber diameter 3,2 μm
Tensile strength ≥ 350 kPa
Classification temperature(maximum service temperature)
1100 °C
Melting point > 1330 °C
DUH PERFORATED TAPE
DESCRIPTION
For hanging spirally coiled pipes in duct system networks.Material perforated galvanized steel tape0,6 x 17 mm – 25 mb0,6 x 25 mm – 25 mb
Box - 10 pcs.Width 28 mmRoll - 25 m
Assembly accessories
Centrum Klima – Products catalogue 131
Assembly accessories
TYPE T ANGLE CONSOLE
USE
To be fi xed on walls, fl oors and ceilings as an assembly profi le.
profi
l noś
ny F
T
L
4
2
132
50
25
30
203011
11
30
90
5
FT L(mm)
30 420
30 510
30 690
DESIGN
Welded structure based on a rectangular base. Galvanized surface.
L
L/2
4
50
40
30°
11H
FT 30x30x2
FT 30x30x1.5L1
40
20
20 15
30
50
5
11
FT L(mm)
L1(mm)
H(mm)
30 510 330 280
30 690 432 329
TYPE T ANGLE CONSOLE (WITH DIAGONAL BAR)
USE
To be fixed on walls, floors and ceilings as an assembly profi le. Thanks to the diagonal support bar it can carry huge loads.
DESIGN
Welded structure based on a rectangular base. Gal-vanized surface.
Centrum Klima – Products catalogue132
TYPE B SHAPE BASE
USE
To be fi xed on walls, fl oors and ceilings as an assembly profi le.
125
455
125 9022/15
DESIGN
Welded structure based on a rectangular base. Galvanized surface.
Assembly accessories
Centrum Klima – Products catalogue 133
Assembly accessories
Fix the nails when the air temperature is minimum 10 °C. It is recommended to use 10 to 12 self-adhe-sive nails per square meter.Procedure:
clean, dry and degrease the surface where the nails are to be fi xedremove the paper and stick the nailscover the nails with insulationinstall the EC pressing blades and, if necessary, protect the nail tip with EP nylon hood
•
•••
USE
HOW TO USE
SELF-ADHESIVE NAILS / NAILS FOR WELDING
Self-adhesive nails are used for mechanical fi xing of insulation materials on smooth surfaces of ventilation ducts.To be used within temperature range from -40°C to +80°C (for a short time up to 100°C).
GS
SAH self-adhesive nailsteel pins, diameter 2,7 mmself-adhesive, galvanized steel base (50/50 mm)solid, synthetic resin rubber glue made of compact cells fi lled with polyurethane foamlength 19-165 mm
•••
•
TECHNICAL DATA
SELF-ADHESIVE NAILS
USE
Welding nails are used for mechanical fi xing of in-sulation materials on smooth surfaces of ventilation ducts. To be used within temperature range from -40°C to +80°C (for a short time up to 100°C).
The nails are fi xed with LF2000 transformator weld-er. They are heated in that way to ensure enough durability but avoid damaging the zinc coating.
HOW TO USE
nail surface is knurled which prevents the blade from slidingEC pressing bladesgalvanized steel elastic bladesexternal diameter 30 or 40 mm. Protective EP nylon hoodplastic hood protecting the nail tip
•
•••
•
NAILS FOR WELDING
Centrum Klima – Products catalogue134
Single sided self-adhesive aluminum insulation tape. Used in production and assembly of AC and ventila-tion devices, dust removing systems as well as heat engineering. To be applied on the insulation bends and forks, on material and mineral wool or glas wool segment connections. Ensures a coherent aluminum insulation layer which prevents water from pen-etrating the system. Hardly combustible according to DIN 4102-1-B1 standard.
Carrier aluminum, thickness: 0,03 mmTotal thickness 0,075 mmGlue: acryl Temperature range: -30°C; +120°CPeel adhesion: 20 N/25mmTensile strength: 37,5 N/25mm
DESCRIPTION
ALUMINUM INSULATION TAPE
Width(mm)
Length(m)
Packaging(pcs)
100 50 12
75 50 16
50 50 24
Single sided self-adhesive aluminum tape reinforced with 5x5 mm carbon fi bre net, laminated with polyeth-ylene. Higher mechanical durability as compared to plain tape. Widely used in technical assemblys.
Carrier aluminum, thickness: 0,03 mmTotal thickness 0,15 mmGlue: acryl Temperature range: -20°C;+80°CPeel adhesion: 25 N/25mm
DESCRIPTION
REINFORCED ALUMINUM INSULATION TAPE
Width(mm)
Length(m)
Packaging(pcs)
100 50 12
75 50 16
50 50 24
Assembly accessories
Centrum Klima – Products catalogue 135
Assembly accessories
Single sided self adhesive tape is perfect for connecting insulations in AC and ventilation systems. It is perfect for all types of repairs. Very good adhesive properties.
Carrier Polyethylene laminated with polyeste-cotton fabric.Total thickness: 0,22 mmGlue: acryl Temperature range: 0°C; +80°CPeel Adhesion: >1.5 N/25mmTensile Strength: 8 N/cm
DESCRIPTION
UNIVERSAL REPAIR TAPE
Width(mm)
Length(m)
Packaging(pcs)
50 50 48
Soft tape made of vinyl polychlorade is designed for pipes and ducts (ventilation and heating) less exposed to weather conditions. It is elastic, which allows for relatively smooth surface after applying the tape.
Carrier Polyethylene laminated with polyeste-cotton fabric. Total thickness 0,08 mmGlue: acryl Temperature range: -15°C;+80°CPeel adhesion: 4,9 N/25mmTensile strength: 88,25 N/25mm
DESCRIPTION
PVC INSTALLATION TAPE
Width(mm)
Length(m)
Packaging(pcs)
50 50 24
Centrum Klima – Products catalogue136
Single sided self adhesive tape with aluminum dust.Used to steam tighten AC or central heating systems. Due to its good adhesive properties and low side pen-etration by water and solvents, it is also widely used in other branches.
Carrier aluminum dusted polypropylene.Total thickness: 0,05 mmGlue: acryl Temperature range: -20°C;+80°CPeel adhesion: 25 N/25mm
DESCRIPTION
PP METALIZED TAPE
Width(mm)
Length(m)
Packaging(pcs)
75 50 64
50 50 96
Single sided aluminum self adhesive tape resistant to temperatures up to 150°C. Used for assembly of AC units, ventilation devices and fi re places.
Carrier aluminum, thickness: 0,05 mmTotal thickness 0,08 mmGlue: acryl Temperature range: -50°C;+150°C
DESCRIPTION
HIGH TEMPERATURE TAPE
Width(mm)
Length(m)
Packaging(pcs)
75 50 16
50 50 24
50 45 24
Assembly accessories
Centrum Klima – Products catalogue 137
DW GALVANIZED DUCT PROFILES, H CORNERS FOR DUCT PROFILES
Production materials
DW 20
DW 30
DW 40
2776
20
27
30
103
30
40
123
H 20
H 30
H 40
● NOTE. The off er available sealing profi les
DW 20 - PROFILE - Metal thickness: 0.6 mm; Length: 5 m
H 20 - CORNER - Metal thickness: 2 mm
DW 30 - PROFILE - Metal thickness: 0.7 mm; Length: 5 m
H 30 - CORNER - Metal thickness: 2,5 mm
DW 40 - PROFILE - Metal thickness: 1 mm; Length: 5 m
H 40 - CORNER - Metal thickness: 3 mm
Centrum Klima – Products catalogue138
CONNECTORS LKK FOR VENTILATION ELBOW AIR FIN
Production materials
18
14DESCRIPTION
This connector allows the user to install air fins with 0.4-1.13 mm sheet metal in ventilation segmented fittings. Made of galvanized steel. Supplied with a rubber gasket which makes the connection air tight.
Packaging - 100 pieces
STIFFENING STEEL CROSS - KUS
45⁰
L
D
DESCRIPTION
Designed for cross connection of big diameters stiff ening pipes. Made of 3 mm galvanized steel, which guarantees resistance to high temperatures necessary e.g. for smoke removing duct systems.L = 70mm, D = 22m
Packaging - 1 piece
Centrum Klima – Products catalogue 139
STIFFENING DISC DU
DESCRIPTION
Diameter D=74 mm Used for stiff ening of big dia-meter rectangular ducts. Prevents deformation of the duct where the stiff ening is installed.Made of 1-1.3 mm thick galvanized steel. Embossing for nut.
Packaging - 1 piece
Ø20 D
STIFFENING GALVANIZED PIPE RUO
DESCRIPTION
Galvanized metal pipe designed for stiff ening big diameter rectangular ducts. Wall thickness ca. 2 mm
16 mm x 6 mb
Production materials
Centrum Klima – Products catalogue140
FLANGE VKPK
n x ød1
ød
øDDETAIL A
DETAIL A
b
s
d 1
a1a
DESCRIPTION
Galvanized steel fl anges are used to produce roof bases, air intakes, roof exhaust vents, etc.
Internal diameter D (mm)
Diameter deviation
(mm)
Thickness S (mm)
Spacing holes D (mm)
Flange width
b (mm)
Flange length on larger diameter
a (mm)
Flange length on smaller diameter a1 (mm)
Outlet diameter
hole d1 (mm)
Number of holes n (pcs)
80 , + 0,50 1-1,5 110 25 11 7 7 4
100 , + 0,50 1-1,5 130 25 11 7 7 4
110 , + 0,50 1-1,5 140 25 11 7 7 4
125 , + 0,50 1-1,5 155 25 18 7 7 4
140 , + 0,50 1-1,5 170 25 18 7 7 8
150 , + 0,50 1-1,5 181 25 20 7 9 8
160 , + 1,00 1-1,5 195 30 20 10 9 8
180 , + 1,00 1-1,5 215 30 20 10 9 8
200 , + 1,00 1-1,5 235 30 21 9 9 8
225 , + 1,00 1-1,5 260 30 20 10 9 8
250 , + 1,00 1-1,5 285 30 20 10 9 8
280 , + 1,00 1-1,5 315 30 20 10 9 8
315 , + 1,00 1-1,5 350 30 20 10 9 12
355 , + 1,00 1-1,5 390 30 20 10 9 12
400 , + 1,00 1-1,5 445 30 20 10 9 12
450 , + 1,00 1-1,5 495 40 20 10 9 12
500 , + 1,00 1-1,5 545 40 20 10 9 16
560 , + 1,00 1,5 605 40 30 11 12 16
630 , + 1,00 1,5 680 45 30 11 12 16
710 , + 1,00 1,5 760 45 30 11 12 20
800 , + 1,00 1,5 860 50 30 11 12 20
Production materials
Centrum Klima – Products catalogue 141
Technical data:
Standard
dimensions
Metal Fabric Metal
35 mm 60 mm 35 mm
45 mm 60 mm 45 mm
70 mm 100 mm 70 mm
Standard
lengths
25 m, packed in separate
cardboard boxes
30,5 m, packed in separate
cardboard boxes
50 m, packed in separate
cardboard boxes
Metal
thickness0.4 mm, galvanized
Technical data:
Standard fabric material PVC* Silicone* Polyurethane*
Coverage Polyester Carbon fibre Carbon fibre
Coating Hardly combustible PVC Silikon Polyurethane
Color Grey — Grey aluminium
Operating temperatures range -40/+80°C
-30/+250°C
momentarily 350°C
class M1
-30/+130°C
400°C for 2 hours
class M0
* other materials are available upon order
Flexible connector
Typ Packaging
XEV-50 PVC 35/60/35 50 m
KEV-50 PVC 45/60/45 50 m
KEV-100 PVC 45/60/45 30,5 m
EEV-100 PVC 70/100/70 30,5 m
XSI-25 SILICONE 35/60/35 25 m
JSI-25 SILICONE 45/75/45 25 m
ESI-100 SILICONE 70/100/70 30,5 m
JPL-100 POLYURETHANE 45/75/45 30,5 m
EPL-100 POLYURETHANE 70/100/70 30,5 m
FLEXIBLE CONNECTOR LE
DESCRIPTION
The fl exible connector is used to prevent trans-mission of vibrations and noise along the duct system. Diff erent types of connections are available (metal or fi bre) so that the user could choose the best solution for installation, fi re protection and economy.
PROPERTIES:
prevents transmission of vibrations and noise along the duct systemair tightcan be used in round rectangular and oval duct systemseasy to use and prefabricate
•
••
•
Production materials
Centrum Klima – Products catalogue142
Damper mechanism with a blockade
KL71/2” damper mechanism with
a blockade for rectangular bolt
KL7/RDamper mechanism with a blockade for round bolt
Damper mechanism
KS385
3/8” Mechanism,
KP7L bolt with springs, KP9L
rectangular bolt
KS385/set
3/8” Mechanism K4,
KP9S rectangular bolt, BKP14
plastic sleeves
KS12
1/2” Mechanism,
KP10R round bolt,
KP10S rectangular bolt
KS12/set
1/2” Mechanism K5,
KP10S rectangular bolt, BKP30
plastic sleeves
KS385
KS12/set
DAMPER MECHANISMS WITH A BLOCKADE
ELEMENTS FOR VENTILATION DAMPERS
DAMPER MECHANISMS
Damper mechanism
KS145
1/4” damper mechanism,
KP6 bolt with a spring,
KP8S square bolt
KSR 195
3/8” damper mechanism,
KP7 bolt with a spring,
KP9S square bolt
KSR195/set
3/8” damper mechanism KR3,
KP9S square bolt,
BKP14 plastic sleeves
Production materials
Centrum Klima – Products catalogue 143
SPIRO DAMPER MECHANISM
DESCRIPTION
Mechanism made of galvanized steel. It is adjusted with the bar located directly above the mechanism’s rotation axis. The set includes bolts, pins and plastic bearing washers. Two screws blocking the damper’s knob in the right position guarantee that the setting will not change.
AC-006 DAMPER MECHANISM
Damper mechanism on a base
MPJ large1/4” damper mechanism
on 2” base
DESCRIPTION
Mechanism for multi-leaf dampers AC-006. In the set you shall fi nd body made from powder-painted steel in black color, aluminum pin and handle form nickled steel. Precise regulation is possible because of a handle supporting the given angle of current setting.
DAMPER MECHANISMS ON BASES
Production materials
Centrum Klima – Products catalogue144
Damper mechanisms for quick installation
RS-356
Damper mechanism (set):
RP1 lever, RB50 bolt with a spring (2 pieces),
RP3 washer,
RP2 wing nut
Multi leaf damper bolts
BKP6 1/2” round bolt, 6” long
BKP71/2” round bolt, 1/2” square bolt,
6” long
DAMPER MECHANISMS FOR QUICK INSTALLATION
MULTI LEAF DAMPER BOLTS
Brass sleeves
BKP10 1/2” brass sleeve
BKP9 7/16” brass sleeve
Plastic sleeves
BKP14 3/8” plastic sleeve
BKP30 1/2” plastic sleeve
SLEEVES
Production materials
Centrum Klima – Products catalogue 145
ZINC-PLATED 12X12 MESH
Zinc-plated 12x12 mesh
Mesh size 12x12 mm
WIR dia. 1,05
Size 1,5 x 30 m (45 m2)
Aplicable:
DESCRIPTION
The mesh is made of zinc-covered 1,05 mm steel wire. It is sold in rolls to make handling and storage easy. Each roll contains 45 m2 (1,5 m x30 m).
INTENDED USE
Zinc-plated mesh can be used extensively by manufacturers of ventilation accessories, such as air intakes and exhausters, diff users, grilles, chimney accessories, etc.
Production materials
Centrum Klima – Products catalogue146
DESCRIPTION
THERMAL INSULATION ADHESIVE MAT MST
Self-adhesive thermal insulation mats MST are made of synthetic rubber foam and rolled into 1 m wide rolls. The mats are used for thermal insula-tion and protection against condensate water of large diameter pipes, tanks and all types of fi xtures in cooling, air conditioning, ventilation, heating, sanitary and special installations.
MST
CHARACTERISTICS
Density: 70÷90 kg/m3
Heat conductivity (W/mK):λ=0,031 (-20°C); λ =0,034 (0°C); λ =0,038 (+40°C)Thermal resistance: -50°C ÷ +110°CSteam dispersion resistance factor:µ > 4500Water absorption: < 5%
Thickness (mm)
Width (m)
Packaging (m2/roll)
6 1 10
9 1 10
13 1 10
19 1 10
Insulation materials
Centrum Klima – Products catalogue 147
ROUND PIPE INSULATION SLEEVE
low transportation and storage costeasy assemblyno need to use special tools for cutting or fi xingPolish Hygiene Certifi cate
••••
USEPRODUCT ADVANTAGES
This insulation is meant to be used with round pipes, for example SPIRO type.
Type Sleeve
Diameter range 80-630 mm
Operating temperature range -30/+140 °C
Insulation thickness 25 mm
Standard length 10 m
Cardboard package roll
DESIGN
Insulated with 25 mm thick mineral wool layer. The external layer is made of aluminum-Polyester laminate reinforced with fi bre wire.
Insulation materials
Centrum Klima – Products catalogue148
USE
WELDER LF 2000
LF 2000 welder is a portable tool for making ventil-lation duct insulations. Its weight (4.5 kg) and size (30 cm long) make it a perfect tool for construction works.
TYPE LF 2000
Voltage 220V 50/60Hz
Operating power 7.5-12 A
Weight 4,5 kg
Power cord 3 m
DESIGN/HOW TO USE
LF 200 is a transformator welder for insulation nails.The regulated power of nail heating ensures enough durability but prevents any damage to the zinc coat-ing.A single work cycle dutration is limited with a built-in safety timer which prevents overheating and ensures the optimum welding time.
PRODUCT ADVANTAGES
Made of very robust palstic and ergonomically de-signed welder ensure easy work and access to nail welding locations.The cover has special holes which prevent over-heating during a constant woking cycle.
•
•
Tools
Centrum Klima – Products catalogue 149
DESCRIPTION
AIR CURTAIN RM
the high and low air speed setting meets the need of multiple applicationsadopted un-electrifi ed surface PTC heater, super safety, fast temperature rising, automatic temper-ature control, creating comfortable air curtainstrong and fast heat generating, stable perform-ance, low electricity consumption, normally start-ing under -18° environmentmicroprocessor control, normal or heating air can be chosen separatelyPTC heater is with over-heated protector, eff ective-ly protecting and energy saving under normal usedelay turnoff protecting device automatically performing when turning off heating air operating state, effi ciently extending product lifemultiple body specifi cations:900mm, 1200mm, 1500mm
•
•
•
•
•
•
•
TYPE Power (kW)
Amp/phase (A)
Motor power (W)
Outlet temperature
(°C)
Air speed (m/s)
Air flow (m3/h)
Noise (dB(A))
Dimensions W×H×D
(mm)
Weight (kg)
RM125-09 3,0 27 165 40-50 6÷7 912 55 900×221×183 15,5
RM125-12 4,5 33 215 40-50 6÷7 1280 57 1200×221×183 19,5
RM125-15 6,0 41 255 40-50 6÷7 1670 59 1500×221×183 23,5
Air curtain
Centrum Klima – Products catalogue150
DESCRIPTION
CIRCULAR DUCT FAN
Circular Duct Fan is our newly develiped series with advanced technology absorbed from oversea and domestic. With standard size, the inlet and outlet at the same diameter could be directly connected with the duct by saving cost in designing. The new design of housing together with high-effi cient centrifugal impeller and high-performance external rotor motor make our duct fan superior to others at the aspects of bulk, weight, vibration, noise, durability, effi ciency and safety. It’s widely used at hotel, auditoriums, supermarkets, stations, airports and other public occasions.
DJT
STRUCTURE
Housing: formed and tooled by quality deep-stretch cold-rolling steel with plastic injection and strong rusty resistance surface. Computerized fl u-id-channel design, it makes high effi ciency for the impeller. The outlet and inlet at the same diam-eter and standard design make it easy to install, maintain and clean.Specifi cations available are: 100 mm, 125 mm, 150 mm, 160 mm, 200 mm, 250 mm and 315 mm.lmpeller diameters: 190 mm, 220 mm, 250 mm, 280 mm and 315 mm are available. Backward-curved impeller matches well with the housing to maximize the airfl ow, effi ciency and minimize the noise level.External Rotor Motor: adopted by single-phrase asynchronous external rotor motor. The impel-ler and motor are directly pressed so that impel-ler could be driven by motor for small duct fan’s cubage, stable performance, high effi ciency and durability. Connecting box: adopted by fi re-resistant fi ber PVC. Quality fi re-proof, safety for usage and easy to disassemble.
•
•
•
•
•
Fans
Centrum Klima – Products catalogue 151
ModelRating
Voltage/Frequency V/Hz
Current (A)
Power (W)
Rotation (rpm)
Air volume (CMH)
Noise (dB)
Insulation Class
DJT10-25B 230/50 0,35 77 2420 248 <55 F
DJT12-35B 230/50 0,42 88 2400 360 <55 F
DJT15-45B 230/50 0,40 88 2470 450 <57 F
DJT16-45B 230/50 0,60 127 2510 580 <59 F
DJT20-46B 230/50 0,81 178 2550 1030 <61 F
DJT25-66B 230/50 0,85 181 2610 1180 <63 F
DJT31-66B 230/50 0,83 163 2650 1500 <65 F
MODEL A (mm)
B (mm)
C (mm)
D (mm)
E (mm)
DJT10-25B 100 242 20 186,00 15
DJT12-35B 125 243 25 189,00 22
DJT15-45B 150 271 20 193,00 20
DJT16-45B 160 345 27 228,00 27
DJT20-46B 200 345 27 228,00 29
DJT25-66B 250 345 27 228,00 29
DJT31-66B 315 400 27 259,00 29
340320300280260240220200180160140120100 80 60 40 20
0 25 50 75 100 125 150 175 200 225 250
DJT10-25B (100mm) DJT12-35B (125mm)
Air flow (m3/h)
Stat
ic p
ress
ure
(Pa)
340320300280260240220200180160140120100 80 60 40 20
0 50 100 150 200 250 300 350 400
Air flow (m3/h)
Stat
ic p
ress
ure
(Pa)
Fans
Centrum Klima – Products catalogue152
340320300280260240220200180160140120100 80 60 40 20 0
0 50 100 150 200 250 300 350 400 450
DJT15-45B (150mm)
Air flow (m3/h)
Stat
ic p
ress
ure
(Pa)
DJT16-25B (160mm)400
375
350
325
300
275
250
225
200
175
150
125
100
75
500 50 100 150 200 250 300 350 400 450 500 550 600
Air flow (m3/h)
Stat
ic p
ress
ure
(Pa)
520
480
440
400
360
320
280
240
200
160
120
80
40
0 150 300 450 600 750 900 1050
DJT20-46B (200mm)
Air flow (m3/h)
Stat
ic p
ress
ure
(Pa)
500
450
400
350
300
250
200
150
100
50
0
0 150 300 450 600 750 900 1050 1200 1350 1500
DJT31-66B (315mm)
Air flow (m3/h)
Stat
ic p
ress
ure
(Pa)
600
550
500
450
400
350
300
250
200
150
100
50
0
-500 200 400 600 800 1000 1200
DJT25-66B (250mm)
Air flow (m3/h)
Stat
ic p
ress
ure
(Pa)
Fans
Centrum Klima – Products catalogue 153
AC/DC powermoment range 4 - 6 - 10 Nmautomatic overload protectionprotection class IP54operating temperature (-10°C ÷ 55°C)operating humidity (0% ÷ 90%)maximum noise level 40 dB(A)connection size Ø (8 ÷ 18 mm) □ (6 ÷ 14 mm)
••••••••
DESCRIPTION CHARACTERISTICS
ON/OFF ACTUATORS
Dependable ON/OFF actuators powered by direct or alternating current.
TD
Type Moment (Nm)
Power supply (V) Signal
Nominalpower (VA)
Restingpower (VA)
Time (s)
Rotation angle(°)
TD04-24 4 24 (AC) 1 30 ÷ 120
TD04-230 4 230 (AC/DC) 2,5 30 ÷ 120
TD06-24 6 24 (AC) 1 30 ÷ 120
TD06-230 6 230 (AC/DC) 2,5 30 ÷ 150
TD10-24 10 24 (AC) 1 30 ÷ 150
TD10-230 10 230 (AC/DC) 2,5 30 ÷ 150
3 &
2
PUN
KTOW
Y
4 ÷ 5
0 ÷ 93
Actuators
Centrum Klima – Products catalogue154
Actuators
AC/DC powermoment range 4 - 6 - 10 Nmautomatic overload protectionprotection class IP54operating temperature (-10°C ÷ 55°C)operating humidity (0% ÷ 90%)maximum noise level 40 dB(A)connection size Ø (8 ÷ 18 mm) □ (6 ÷ 14 mm)
••••••••
DESCRIPTION CHARACTERISTICS
PROPORTIONAL ACTUATORS
Dependable proportional actuators powered by direct or alternating current.
TA
Type Moment (Nm)
Power supply (V) Signal
Nominalpower (VA)
Restingpower (VA)
Time (s)
Rotation angle(°)
TA04-24 4 4 ÷ 5 60 ÷ 110
TA06-24 6 5 ÷ 8 30 ÷ 150
TA10-24 10 5 ÷ 8 30 ÷ 150
DC0(2)-10V
0 ÷ 95
24 (AC/DC)
1 - 2,5
Centrum Klima – Products catalogue 155
Presostat
PRESOSTAT TP33B
MEASUTING RANGE
(Pa)
Operating temperature(°C)
Protection level
Output contact parameters
Weight(g)
Dimensions(mm)
30 ÷ 300 od -15 do +60 (overpressure 100 Pa) IP54 250V 2A,
switch contact 100 Ø 81 x 53
fi lter stuck alarmair fl ow control in ventilating ductsair control in gas burnermaximum air fl ow control in systems with variable air volume
••••
USE TYPICAL APPLICATIONS INCLUDE
TP33B pressure controls may be used for detec-tion of pressure (diversifi ed) and air fl ow in pipes and ducts.
NOTE
TP33B pressure controls are designed to be able to block or detect non diversifi ed pressure. If critical or high values are to be maintained in a given environment, a single device should not be used as both operating and protective device. In case of such applications, an additional control device with alarm contacts should be connected, which will signal the operation of the control device.
Centrum Klima – Products catalogue156
DIAMETER RANGE
Diameter range for ducts Diameter range for fittings
D nom (mm)
D tol. (mm)
min.-max.
D nom (mm)
D tol. (mm)
min.-max.
80 80,0 – 80,5 80 78,6 – 79,5
100 100,0 – 100,5 100 98,6 – 99,5
125 125,0 – 125,5 125 123,6 – 124,5
150 150,0 – 150,6 140 138,6 – 139,5
160 160,0 – 160,6 150 148,5 – 149,5
180 180,0 – 180,7 160 158,5 – 159,5
200 200,0 – 200,7 180 178,5 – 179,5
224 224,0 – 224,8 200 198,4 – 199,5
250 250,0 – 250,8 224 222,4 – 223,5
280 280,0 – 280,9 250 248,3 – 249,5
300 300,0 – 300,9 280 278,3 – 279,5
315 315,0 – 315,9 300 298,2 – 299,5
355 355,0 – 356,0 315 313,2 – 314,5
400 400,0 – 401,0 355 353,2 – 354,5
450 450,0 – 451,1 400 398,1 – 399,5
500 500,0 – 501,1 450 448,1 – 449,5
560 560,0 – 561,2 500 497,9 – 499,3
630 630,0 – 631,2 560 557,9 – 559,3
710 710,0 – 711,5 630 627,8 – 629,3
800 800,0 – 801,6 710 707,1 – 709,3
900 900,0 – 902,0 800 798,0 – 799,3
1000 1000,0 – 1002,0 900 897,9 – 899,3
1250 1250,0 – 1252,5 1000 997,9 – 999,3
1600 1600,0 – 1603,3 1250 1247,8 – 1249,3
1600 1597,1 – 1599,1
Centrum Klima – Products catalogue 157
COLLECTIVE PACKAGE SIZES P
Code Lenght (mm)
Witht (mm)
Height(mm)
Weight (kg)
Volume (m3) Box/Pallet
P1 1200 800 800 4,63 0,770 1
P2 600 800 800 2,83 0,380 2
P4 600 400 800 1,34 0,190 4
P6 400 400 800 1,04 0,130 6
P12 400 400 400 0,71 0,064 12
P24 400 400 200 0,52 0,032 24
P1
P6
P2
P12
P4
P24
Centrum Klima – Products catalogue158
AAF012 - not insulated fl exible ducts ....................................50
AF012ECO - not insulated fl exible ducts ..............................52
AF013 - insulated fl exible ducts ......................................... 51
AF013ECO - insulated fl exible ducts ...................................53
AF019 - insulated fl exible ducts ......................................... 51
AF019ECO - insulated fl exible ducts ...................................53
AI - grille (steel mesh) ...................................................... 94
BB9/B9X/B9Z/B9MB - bend 90° .......................................... 9
B6/B6X - bend 60° ...........................................................10
B4/B4X/B4Z/B4MB - bend 45° ..........................................11
B3/B3X - bend 30° ........................................................... 12
B1/B1X - bend 15° ............................................................. 13
BB - galvanized screw ..................................................... 128
BK - stainless steel screw ................................................ 129
BS/BSX - sectional bend 90°, 60°, 45°, 30°, 15° ................. 14
BSN - segmented bend 90°, 45° (stainless steel) ................ 15
BUS - branching with net ................................................. 36
CCA/CN - chimney root Centrowent .................................... 102
CB - branching overl aying round duct ................................37
CDO - Roof round air intake type C .................................... 82
CM - metal band clip ........................................................116
CMB - metal clip tape ......................................................117
CMC - metal clip tape .......................................................117
CMN - nylon band clip ......................................................118
COMBIFLEX - fl exible PVC laminated duct ...........................59
CW - galvanized steel rectangular air intake/exhauster .......77
CWA - Anodized aluminum rectangular
air intake/exhauster .............................................. 78
DD/DX/DXH - duct end cap ..................................................43
DF/DFH - fi tting end cap ....................................................45
DJT - circular duct fan ...................................................... 150
DS/DSX - single blade round damper .................................61
DSN - single-leaf round damper (stainless steel) ................ 64
DSP - round connection ...................................................101
DSXS - air-tight single-leaf round damper ......................... 63
DU - stiff ening disc ......................................................... 139
DUH - perforated tape ..................................................... 130
DW 20/DW 30/DW 40 - galvanized duct profi les ............... 137
FFAD - inspection hatches on rectangular duct ........... 74
FB - branching overl aying rectangulare duct .............37FKO - circular duct fi lters ......................................... 92FS - casette fi lters ................................................... 93
GGS - self-adhesive nails / nails for welding .............. 133
HH 20/H 30/H 40 - corners for duct profi les .............. 137HF/HN - roof round air intake/exhauster .................. 85
IIL/ILX - straight branching ...................................... 46IL4/IL4X - 45° cylindrical branching ......................... 47ILR/ILRX - pressed straight branching ....................... 48IRIS - duct damper .................................................. 65
KK - roof air intake .....................................................81KEO-K - circular fl exible connector pipes .................. 96KEP - rectangular fl exible duct connectors ................ 95KWO-AL - round intake/exhauster .............................75KR - Cleanout hatches ............................................. 73KUS - stiff ening steel cross .................................... 138
LL - suspension profi le with shock absorbing rubber ....121LE - fl exible connector ............................................ 141LF 2000 - welder ...................................................148LKK - connectors for ventilation elbow air fi n ........... 138LN - connecting nut ...............................................128
NNK - stainless steel nut ..........................................128NN - galvanized nut ...............................................128
MM0 - not insulated fl exible ducts ............................. 54M0izo - insulated fl exible ducts ................................55MST - thermal insulation adhesive mat ...................146
OOFK - round duct fi lters ............................................91OM - supressing bands .......................................... 119OPO/OPOX - pipe clips for round ducts ....................115
PPD - roof base B-I, B-II, B-III ..................................... 87
ABC Index
Centrum Klima – Products catalogue 159
ABCIndex
PD-P - rectangular roof base type A .......................... 88PD-S - rectangular roof bases .................................. 89PD-ST - rectangular attenuating roof base ................ 90PES - gasket .......................................................... 129PEST - temperature resistant gasket ....................... 130PJ - single blade rectangular damper ....................... 68POLYFLEX HEAVY DUTY - fl exible PVC duct ................. 58PS/PSX - colar saddle ............................................. 32PS4/PS4X - 45° branching for round ducts ................35PSE/PSK - Automatic aluminum dampers .................. 71PW - multi blade rectangular damper ....................... 69
RR / V suspension profi le with shock
absorbing rubber .......................................... 122RC/RCX - pressed reducer ........................................16RCF/RCFX - pressed reducer ..................................... 17RD - access door for a rectangular duct .................... 72RM - air curtain ..................................................... 149RN/RNX - asymmetrical segmented reducer ............. 22RS/RSX - symmetric segmented reducer ...................18RSK - back draft damper ......................................... 67RSN - symmetrical reducer (stainless steel) ...............21RTN - chimney roots Rotofl ex ..................................104RUO - stiff ening galvanized pipe ............................. 139RZ - coil pipe ............................................................ 6RZN - coil pipe (stainless steel) .................................. 8
SS-FLEX - semi fl exible aluminum duct non insulated ... 56SLEEVE - round pipe insulation ............................... 147SO - net straight branching ..................................... 49SR - plenum box ..................................................... 97SR-HB40 - plenum box ............................................ 98SR-SD-B - plenum box ............................................. 99SR-SD-C - plenum box ............................................100
TTA - proportional actuators .................................... 154TAE - fl exible acoustic silencer ................................ 114TAO - round acoustic silencers ................................ 107TAO S-FLEX - fl exible round silencers ...................... 112TAP - rectangular acoustic silencers .........................113TD - ON/OFF actuators ........................................... 153TP33B - presostat .................................................. 155TS/TSX - symmetric pipe–tee .................................. 23TSHF/TSHFX - symmetrical tee ................................. 30TSN - symmetrical tee (stainless steel) ......................31TSY/TSYX - twin bend ............................................. 38
VV/VX - coupling ...................................................... 39VF - sleeve ..............................................................41VFN - sleeve (stainless steel) ................................... 42VH - chimney .........................................................106VKPK - fl ange ........................................................140VLA - round intake/exhauster (CrNi steel) ................ 76VN - coupling (stainless steel) ................................. 40
WW 2/W 105/W 106/W 107/W 41 - assembly profi le - galvanized ............120WDC - round gravity ventilator ................................. 86WDO-C - roof circular air exhauster/intake type C ..... 83WDO-D - roof circular air intake/exhauster type D ..... 84WDP-A - roof rectangular air intake/exhauster type A .. 79WDP-B - roof rectangular air intake/exhauster type B .. 80WW - enlarged galvanized washer .......................... 129
ZZ - suspension profi le with shock absorbing rubber ...121
LOCATION MAPOutline map of Warsaw with access routesto Centrum Klima’s office and warehouse.
Poznańska
Świerkowa
Świerkow
a
Ogrodni
cza
Sochaczewska
Sochaczewska
PiotrkówekDuży
Poznańska
Giełda Bronisze
Wieruchów
Bronisze
Poznań
Warszawa
Stare Babice
WieruchówPoland05-850 Ożarów Mazowiecki, 144 Sochaczewska street phone: +48 22 250 50 50
fax: +48 22 250 50 60
Monday - Friday: 8 am - 4 pmSaturday: 8 am - 2 pm
Fundusze Europejskie – dla rozwoju innowacyjnej gospodarkiInwestujemy w waszą przyszłość
Obecnie realizujemy projekt współfinansowany przez Unię Europejską z Europejskiego Funduszu Rozwoju RegionalnegoPOIG.6.1 Etap II
1. Products, technical details and prices were included herein only for information purposes. They may change, for instance due to product upgrade, without prior notice and should not be understood as Centrum Klima’s direct off er. The company may not be held responsible for potential mistakes or inaccuracies which may arise herein.
2. The products and prices expressed herein do not include VAT and are not a business off er in the meaning of commercial law regulations. Centrum Klima reserves the right to alter the prices without any form of notifi cation.
3. All dimensions are expressed in millimetres unless stated otherwise.
Okladka_ANG_2012.06_grzbiet.indd2 2 2013-01-31 13:31:15
Your climate solution center
www.centrumklima.plwww.centrumklima.pl
POLAND05-820 Piastów, 4 Noakowskiego streettel. +48 22 753 71 72fax +48 22 753 42 80
POLAND02-237 Warsaw, 7B Instalatorów streettel. +48 22 868 25 28fax +48 22 886 48 87
Centrum Klima S.A.
Products catalogue
Distributor
Centrum Klima S.A. Wieruchów05-850 Ożarów Mazowiecki, 144 Sochaczewska streetphone: +48 22 250 50 50fax: +48 22 250 50 60
klient@centrumklima.pl www.centrumklima.co.uk www.centrumklima.co.uk
Okladka_ANG_2012.06_grzbiet.indd1 1 2013-01-31 13:31:14