PXD Grounding & Shielding...•IEC 61000-5-2 Ed 1.0 (1997): EMC-Installation and mitigation...

transcript

PXD Grounding & Shielding

Fernando Arteche

MPI - February 2017

1. PXD GROUNDING • PXD ground have been defined in several documents that

have been prepared during the project. – Safety and equipment protection ground

– Detector Performance ground (Noise ground)

• Safety & Equipment protection ground (Installation) – Metal parts that can be energized – should be grounded

– Ground connections - Bonding and straps (size, etc)

– Electrical Laboratory codes and Low Voltage directive • IEC 61000-5-2 Ed 1.0 (1997): EMC-Installation and mitigation

guidelines: Earthing and cabling

• IEC 62305-1 to 4 Ed 1.0 (2006): Protection against lightning

• IEC 60364-5-54 Ed 3.0 (2011): Electrical installations of buildings. Selection and erection of electrical equipment- Earthing arrangements, protective conductors and protective bonding conductors.

• Detector performance ground ……

2 de 11 Grounding Meeting

February, 2017, MPI, Germany

• Cooling blocks is defined as PXD local ground – Cooling blocks (both sides) connected via low impedance

– PXD local ground connected to experiment ground

• PXD electronics ground (each leader) is connected to the cooling blocks (Multipoint ground topology)

• Cooling pipes isolated & grounded

1. PXD GROUNDING

• Local ground implementation : Cooling blocks

– A unique ground structure for all PXD (Stainless steel) • It should guarantee the same potential from DC to hundreds of MHz of all

PXD electronics

* Plots: Tscharlie Ackermann

• Both sides connected together via CF tubes

– Beam pipe connection is not allowed

– Special coating needed to guarantee DC connection

– R < ????? mohm

1. PXD GROUNDING

• Local & detector gorund implementation : electronics gnd connection

– AGND-DGND: Already have a common point at module level

– A connection to local ground and detector ground are needed ????

To detector ground connection

Half block connection

1. PXD GROUNDING

• Local ground implementation : Cooling pipes – CO2 and airflow pipes are electrically isolated

towards the outside via ceramic joint • Inner part is grounded to cooling blocks

– It avoids any noise penetrated to detector electronics

• External part should be grounded to detector – Safety requirement (Belle Il requirements) – No floating metallic pieces

Ceramic joint located around ???? mm from the CB

Local GND Exp GnD

* Plots: Tscharlie Ackermann

1. PXD GROUNDING

2. CABLING • PXD have a complex topology for cabling the sub-detector.

– Voltages & Currents: Signal, Power & slow control cables

• Cables has been changed since last grounding discussion (2014)

• Attention has been paid to the cabling shielding because it may lead to some integration problems.

• Cable shield connection mainly defined by Belle II rules

– Both sides connection will be the preferred option

– Floating shields has to be minimized

– Other options need to be justified

•Infiniband: Data Transmission Shielded & TSP Data, Ctrl, sense

•Kapton: Power, control & Data Power (up to 30V , 2A) Sensing (LV , mA) ?? Data, Ctrl, JTAG

•CAT6 : JTAG Shielded ??

2. CABLING

•Service cable 1 (x2): Power Power Inner Shields External Shields

•LVDS cable (20pin): Power & control Ctrl Power ?? Sensing (LV , mA) JTAG Shielded ??

2. CABLING

•Service cable 2: Power & control Power (up to 30V , 2A)

No inner shields

• JBX is considered the entrance to Vertex volume – It is the last good ground

• Shields connections: – External shields

• 15m long cables – Shield connected to both sides – It protects against electric and magnetic fields

– It decreases the ability of the cable to radiate

• 2m long cable – Shield connected 1 side (JBX side) – Electrostatic protection

– External and inner shields are independent

– Inner Shields • Floating or connected 1 side (JBX side)

– Drain wires not connected

2. CABLING

3. SUMMARY

BACKUP SLIDES

2. PXD GROUNDING • Several issues have been considered in the grounding

definition of PXD systems. Multipoint grounding topology.

Short ground connections

Belle II General Meeting June 18-21, 2014, KEK, Japan

2.2 Grounding topology: Grounding implementation - Straps

Common Belle II SVD-PXD Meeting

February 2012, Vienna, Austria 14 de 18

• Multiple equipment or units must be connected to a signal reference system (SRS) for direct connection bonding straps are required • Bounding straps: impedance highly influenced by inductance L, dependent on geometry resonances must be avoided

Local ground at detector level (HF conection)

Short connections

2. PXD GROUNDING

2. PXD GROUNDING • Standards

PXD Detector

Multipoint ground Topology

1.1 PXD GROUNDING: Topology

2.1 PXD GROUNDING: Topology

3.CABLING

PXD Grounding & Shielding...•IEC 61000-5-2 Ed 1.0 (1997): EMC-Installation and mitigation...

Documents