Post on 11-Dec-2021
transcript
www.metrans.com.tr
RHEINHUETTE: SPECIAL MATERIALS FOR SPECIAL APPLICATIONS
As experts in corrosion and wear resistant materials Rheinhütte offers process and media-specific
solutions. Rheinhütte will select the right material for your conveyance requirement and will ensure
minimum wear during long operational life – even when handling difficult media.
PLASTICS
In pump engineering the non-metallic materials which are mainly used, are predominantly fluoropolymers
and polyolefins. The advantage of these materials is their high resistance to acids and alkalis at low to
medium temperatures. To resist external forces these pump types are usually protected by a metal casing.
Mineral casting/ composite material
Polymercarbide
A corrosion- and wear-resistant material that promises significantly longer service life and thus lower life
cycle costs than conventional materials in pump construction, especially in chemically aggressive media.
Fluorpolymere
Polyvinyliden-Fluoride PVDF
PVDF is characterized by its excellent general corrosion resistance, high resistance to stress cracking and
good UV resistance. Its usable temperature range is between -20 °C and 130 °C. The material is especially
suitable for pumping hydrofluoric acid of all concentrations up to boiling point, liquids containing halogen,
nitric acid/hydrofluoric acid pickles and for the evaporation of spent hydrochloric acid.
Perfluoralkoxi PFA
PFA is a perfluorated alkyvinyl ether. Centrifugal pumps lined with PFA can be used up to 180 °C. With a
few exceptions this material has a universal resistance to chemicals.
Polytetrafluorethylene PTFE
PTFE shows an outstandy resistance against nearly all organic and inorganic media over a wide
temperature range. Centrifugal pumps made of PTFE can be used between -50 °C and 180 °C.
Polyolefins
Polypropylene PP
In many applications PP represents an economical alternative to high grade metallic materials. This
material is suitable for pumping salt solutions, almost all dilute alkalis and acids and is also frequently used
in hydrochloric acid pickling solutions. It can be used for working temperatures between 0 °C and 100 °C.
metrans
www.metrans.com.tr
Polyethylen PE 1000 UHMW-PE
Only ultra high molecular weight low pressure polyethylene is used. Its usable temperature range is
between -50 °C and 80 °C. Its general corrosion resistance exceeds that of PP in some cases. Due to its
very good wear resistance, centrifugal pumps made of PE are very often used in media that are both
corrosive and abrasive, such as in flue gas cleaning.
Polyethylene PE 1000 R
PE 1000R is a further development of the standard polyethylene PE 1000 with wear-minimizing additives
for up to 20% higher resistance - for use in highly abrasive suspensions with process-related critical solids
content. The material can be used at temperatures from -20 °C to +80 °C.
METAL
The range of metallic materials encom-passes a wide variety of very different types of material which are
distinguished mainly by their alloy composition, their structure and their manufacturing process. This gives
each material its characteristic properties and allows an optimal material to be selected to suit the
application.
Cast Iron and Cast Steel
Ferritic cast steel 1.0619
High temperature ferritic cast steel, can be used up to 450 °C. For use with low or non-corrosive media,
such as molten sulphur.
Ferritic cast steel 1.7357
High temperature ferritic cast steel, can be used up to 450 °C. The most frequent application is the
pumping of molten salts.
High Alloy Cast Steel V5700 (0.9650)
Particularly wear resistant high alloy cast iron. This material is used for suspensions with an abrasive effect
such as gypsum, carbonates, carbides. sand, ore or metal oxides.
High Alloy Cast Steel
Ferritic stainless steel 1.4136S
Corrosion and erosion resistant high alloy ferritic cast steel. Typical applications are highly concentrated
sulphuric acid up to 180 °C, oleum, fertilizer production, crude and solid phosphoric acid.
Ferritic stainless steel RHRS
Corrosion and erosion resistant high alloy ferritic cast steel. Typical applications are highly concentrated
sulphuric acid up to 225 °C, oleum, fertilizer production, crude and solid phosphoric acid.
metrans
www.metrans.com.tr
Austenitic stainless steel RHSX
Special high-alloyed material with excellent resistance to erosion-corrosion for pumps operating in the
dryer-, intermediate- and end-absorber stage of sulphuric acid plants up to temperatures of 150 °C.
Austenitic stainless steel 1.4306S
High-quality, molybdenum-free material suitable for applications such as pumping of ammonium nitrate
melt, hot nitric acid at medium concentrations and also the vaporization of waste nitric acid.
Austenitic stainless steel 1.4361
Low carbon silicon alloy material for pumping strongly oxidising media. Particularly suitable for hot highly
concentrated nitric acid, e.g. 98% HNO3.
Austenitic stainless steel 1.4408
Austenitic chromium nickel molybdenum steel with a good general resistance to corrosion. These
materials are suitable for pumping almost all organic liquids, 50% caustic soda up to 90 °C, KTL paint, pure
phosphoric acid, dry chlorine, liquid sulphur, PTA and many other media.
Austenitic stainless steel 1.4581
Austenitic chromium nickel molybdenum steel with a good general resistance to corrosion. These
materials are suitable for pumping almost all organic liquids, 50% caustic soda up to 90 °C, KTL paint, pure
phosphoric acid, dry chlorine, liquid sulphur, PTA and many other media.
Semi-austenitic 1.4463
Semi-austenitic, easily welded material with an increased strength and a good general resistance to
corrosion. Due to its good welding properties and wear resistance it is frequently used for jacketed pumps
for handling melts containing solids, such as pitch and tar.
Duplex 1.4517
Duplex (semi-austenitic), molybdenum and copper alloyed material with a high resistance to pitting and
stress corrosion. This material is one of the super duplex steels. lt can be used with crude phosphoric acid,
containing solids at up to 100 °C, hot sea water, many solutions containing chloride, FGD suspensions and
sulphuric acid at all concentrations at low temperatures.
Fully austenitic special stainless steel R3020
Fully austenitic special stainless steel with a high chromium and nickel content. High resistance to pitting,
stress corrosion and intercrystalline corrosion. Suitable for 70% caustic soda up to 200 °C, sulphuric acid at
all concentrations at low and medium temperatures, sulphuric acid pickling solutions, in certain areas of
the manufacture of phosphoric acid, for pumping solutions with a high chloride content and in spin baths.
metrans
www.metrans.com.tr
High austenitic stainless steel 1.4529S
High-quality, fully austenitic cast material with high resistance in chloride-rich, acidic and solid media. Use
in REA absorber and quencher liquids, for acidic and chloride-containing gypsum sludge, in phosphoric
acid production, in evaporation and crystallization processes as well as in hot sea water.
Higher austenitic stainless steel 1.4652S
Higher austenitic cast material with very high corrosion resistance. Especially in very corrosive phosphoric
acid with solids this material is perfectly suitable.
Silicon Iron Alloys
SIGUSS
Highly corrosion resistant chromium alloy silicon cast iron with a good resistance to wear and increased
chemical resistance. This material is chemically resistant to H2SO4 at all concentrations up to boiling
point, therefore for all sulphuric acid applications including the evaporation of waste sulphuric acid, Siguss
is virtually indispensable.
Nickel Based Materials
Alloy C1 (2.4686)
Highly resistant nickel-base alloy for special applications such as liquids containing high chloride,
hydrochloric acid, FGD liquids, very heavily contaminated phosphoric acid, hypochlorites and solutions
with oxidising chlorides.
Alloy C22 (2.4602)
Highly resistant nickel-base alloy for special applications such as liquids containing high chloride,
hydrochloric acid, FGD liquids, very heavily contaminated phosphoric acid, hypochlorites and solutions
with oxidising chlorides.
Alloy B1 (2.4685)
Highly resistant nickel-base alloy for special applications such as liquids containing high chloride,
hydrochloric acid, FGD liquids, very heavily contaminated phosphoric acid, hypochlorites and solutions
with oxidising chlorides.
Pure Metals
Titan (3.7031)
Titanium is especially resistant to heavily oxidising and chloride containing media. The material is
preferred for use in chloralkali-electrolysis, for pumping bleaching solutions containing chlorine and in the
manufacture of acetic acid.
Titan Pd (3.7032)
Titanium alloyed with palladium. This improves the corrosion resistance in reducing media, e.g. in
solutions of iron chloride or aluminium chloride containing hydrochloric acid.
metrans
www.metrans.com.tr
Nickel (RH Ni 98)
Nickel is mainly used for pumping molten alkalis, for the evaporation of alkalis and for pumping highly
refined alkalis which must not be contaminated with iron ions.
Ceramics
Pumps made of ceramic materials are particularly suitable for media which are highly abrasive and at the
same time corrosive, where pumps made from metallic materials and plastics may have a relatively short
operational life.
Metrans Makina is the only authorized Rheinhütte distributor and service provider in Turkey.
metrans