Post on 12-May-2018
transcript
Process Pump
RPHmdp
Type Series Booklet
Legal information/Copyright
Type Series Booklet RPHmdp
All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,edited or processed for any other purpose, nor otherwise transmitted, published or made available toa third party without the manufacturer's express written consent.
Subject to technical modification without prior notice.
© KSB Aktiengesellschaft, Frankenthal 05.09.2013
Contents
Mag-drive Pumps ...............................................................................................................................................4
Process Pumps .................................................................................................................................................................4
RPHmdp ..................................................................................................................................................................... 4
Main applications ................................................................................................................................................ 4
Operating data ....................................................................................................................................................4
Designation .......................................................................................................................................................... 4
Design details ....................................................................................................................................................... 4
Bearing life ........................................................................................................................................................... 5
Materials ..............................................................................................................................................................5
Coating and preservation ...................................................................................................................................7
Product benefits .................................................................................................................................................. 7
Acceptance tests / Warranties ............................................................................................................................. 7
Pressure and temperature limits ......................................................................................................................... 7
Sizes ...................................................................................................................................................................... 8
Technical data ...................................................................................................................................................... 9
Selection charts ................................................................................................................................................. 10
RPHmdp, n = 2900 rpm ................................................................................................................................ 10
RPHmdp, n = 1450 rpm ................................................................................................................................ 11
RPHmdp, n = 3500 rpm ................................................................................................................................ 11
RPHmdp, n = 1750 rpm ................................................................................................................................ 12
Dimensions and connections ............................................................................................................................12
General assembly drawing with list of components .......................................................................................14
Contents
3
Mag-drive Pumps
Process Pumps
RPHmdp
Main applications
Pump for handling the large variety of crude oil products inrefineries as well as in the chemical and petrochemicalindustry.
▪ Refineries
▪ Chemical industry
▪ Petrochemical industry
Operating data
Operating properties
Characteristic ValueFlow rate Q Up to 300 m3/hHead H Up to 270 mOperating temperature T -40 °C to +300 °C1)
Operating pressure2) p Up to 51 bar (at 20 °C)
(ASME B 16.5 class 300)
for A 216 Grade WCB
Designation
Example: RPHmdp S6 80-280
Key to the designation
Code DescriptionRPHmdp Type seriesS6 Material variant to API 61080 Nominal discharge nozzle diameter [mm]280 Nominal impeller diameter [mm]
Design details
Design
▪ Volute casing pump
▪ Horizontal installation
▪ Back pull-out design
▪ Single-stage
▪ Meets technical requirements to API 610, 11th edition /ISO 13709 / API 685
Pump casing
▪ Volute casing with integrally cast pump feet
▪ Centreline pump feet
▪ Single or double volute, depending on the pump size
▪ Radially split volute casing
▪ Axial inlet nozzle, tangential discharge nozzle pointingvertically upwards
▪ Volute casing with casing wear ring
▪ Casing cover (with casing wear ring, as required)
Optional:
▪ Casing and casing cover heatable/coolable, depending onsize
Impeller type
▪ Closed radial impeller
▪ Impeller with impeller wear ring on the suction side
▪ Sealing gap and balancing holes balance axial forces
Optional:
▪ Inducer to improve the NPSH value
Shaft seal
▪ Magnetic coupling to API 685
Bearings
▪ Uncooled
Drive-end bearing:
▪ Fixed bearing
Roller bearing
▪ Axial movement of the rotor limited to 0.5 mm maximum
▪ Oil bath lubrication
▪ Optional: oil mist lubrication
Pump-end bearing:
▪ Radial bearing
▪ Cylindrical roller bearing
▪ Absorbs radial loads only
▪ Oil bath lubrication
▪ Optional: oil mist lubrication
1) Operating temperatures below -40 °C or above 300 °C on request2) Higher pressures and flange pressure ratings on request
Mag-drive PumpsProcess Pumps
4 RPHmdp
Bearing life
The calculated minimum bearing life is:
▪ 25,000 h to API 610
Materials
Materials
Part No. Description Design
S13) S54)5) S6 S8 A8 C6 D1
102 Volute casing CS 316AUS 12Cr DSS161 Casing cover
(uncooled)CS 316AUS 12Cr DSS
Casing cover(cooled)
CS 316AUS 12Cr DSS
210.02 Shaft6) CS 12Cr+H 4)
4140AS5)12Cr+H 3)4)
4140AS 5)
DSS DSS316AUS5)
12Cr+H 3)4)
12Cr5)
DSS
230 Impeller CI CS 12Cr 316AUS 316AUS 12Cr DSS330 Bearing
bracketCS
411.10 Joint ring AUS/ graphite DSS/graphite
502.01/02 Casing wearring
27Cr 27Cr12Cr+H 4)5)
316AUS 316AUS316AUS+HF4)
12Cr 5)
27Cr12Cr+H4)5)
AUSDSS4)5)
503.01/02 Impeller wearring
12Cr+H 12Cr+H 316AUS 316AUS12Cr5)
12Cr+H AUSDSS4)5)
902.01/920.01 Casing screws/hexagon nut
CrMoV / CrMo 4140AS4)5)
Material variant for pump components
Description Material class Material
Europe Asia AmericasCast components, general CI JS1025 - -
CS A216 Gr WCB A216 Gr WCB A216 Gr WCB316AUS 1.4408
1.4409A743 Gr CF3M A743 Gr CF8M
A743 Gr CF8M
12Cr 1.4008 A743 Gr CA6NM A743 Gr CA6NM27Cr VG434 - -DSS 1.4593
A890 Gr 1BA890 Gr 1B A890 Gr 1B
Pressure-retaining castcomponents
CS A216 Gr WCB A216 Gr WCB A216 Gr WCB316AUS A351 Gr CF3M
A351 Gr CF8MA351 Gr CF3MA351 Gr CF8M
A351 Gr CF8M
12Cr A217 Gr CA15 A487 Gr CA6NM A487 Gr CA6NMDSS 1.4593
A995 Gr 1BA995 Gr 1B A995 Gr 1B
Bar stock(shaft 210.01)
CS C45+N - -CrMo 1.7709 - -316AUS - - A276 Type 3164140AS - - A434 Cl. BB12Cr - - A276 Type 42012Cr+H 1.4021+QT700 A276 Type 410 H&T -DSS 1.4462 AISI 329
1.44621.4462
Bar stock(shaft 210.02)
AUS 1.4539 - -316AUS 1.4571 A 276 Type 316 AISI 316
A276 Type 316
3) Europe4) Asia5) Americas6) Above 250 °C: CrMo; -10 °C to 250 °C: CS; -40 °C to +300 °C: DSS
Mag-drive PumpsProcess Pumps
RPHmdp 5
Description Material class Material
Europe Asia Americas12Cr - - AISI 420
A276 Type 42012Cr+H 1.4027+QT 1.4024.19
A276 Type 410 H&TAISI 420 Hard
DSS 1.4462 AISI 329 1.4462
1.4462
316AS+HF - A743 Gr CF8M + Colmonoy Coating
-
Screw/bolt/stud 4140AS - A193 Gr B7 A193 Gr B7CrMo 1.7709 - -
Nut 4140AS - A194 Gr 2H A194 Gr 2HCrMo 1.7258 - -
Abbreviations used
Abbreviation MaterialCI Cast ironCS Unalloyed steel316AUS Austenitic stainless steel >2 %
molybdenum12Cr 12 % chrome steel27Cr 27 % chrome steelDSS Duplex stainless steel4140AS 4140 alloyed steel+H Hardened+HF Hard-faced
Table of comparison of materials
Material type Code Material No. Standard Closest ASTM equivalentCast iron GJS–400–15 JS1030 EN 1563 A 536 Grade 60–40–18
GJS–400–18–LT JS1025 EN 1563 A 536GJL–250 JL1040 EN 1561 A 48 Class 30
Cast steel GP240GH+N 1.0619+N EN 10213–2 A 216 Grade WCBCast stainless steel GX5CrNiMo19–11–2 1.4408 EN 10213–4 A 351 Grade CF8M
GX5CrNiMo19–11–2 1.4408 EN 10213 A 743 Grade CF8MGX2CrNiMo19–11–2 1.4409 EN 10213–4 A 351 Grade CF3MGX2CrNiMo19–11–2 1.4409 EN 10213 A 743 Grade CF3MGX3CrNiMoCuN24–6–2–3 1.4593 - -GX2CrNiMoCuN25–6–3–3 1.4517 EN 10213 -
Cast chrome steel GX20Cr 14+QT 1.4027+QT SEW 410 A 743 Grade CA15GX35CrNiMo25–4 VG 434 KSB materials data sheet
Material identificationcode 2800
-
GX7CrNiMo12–1 1.4008 EN 10283 A 743 Grade CA15GX8CrNi12 1.4107 EN 10213–2 A 217 Grade CA15GXZ5CrNi13–4 1.4317 EN 10213–2 A 487 CA6NMGXZ5CrNi13–4 1.4317 EN 10283 A 743 CA6NM
Stainless steel X6CrNiMoTi17–12–2 1.4571 EN 10088 A 276 Type 316TiX2CrNiMoN22–5–3 1.4462 EN 10088 A 182 Grade F51
Chrome steel X20Cr13+QT700 1.4021+QT700 EN 10088 A 276 Type 420X20Cr13 1.4021 EN 10088 AISI 420 HardX15Cr13 1.4024.19 KSB materials data sheet
Material identificationcode 1219
A 276 Type 410
X29CrS13 1.4029 EN 10088 -X12Cr13 1.4006 EN 10088 A 276 Type 410 H&TX5CrNiMo17–12–2 1.4401 EN 10088 A 276 Type 316X4CrNiMoN27–5–2 1.4460 EN 10088 AISI 329X2CrNiMoN17–13–3 1.4429 EN 10088 A 276 Type 316L
Steel which is creep-resistant at elevatedtemperatures
21CrMoV5–7+QT 1.7709+QT EN 10269 A 193 Grade B16P355GH 1.0566 EN 10028–3
Carbon steel C45+N 1.0503+N EN 10083 A 576 Grade 1045
Mag-drive PumpsProcess Pumps
6 RPHmdp
Material type Code Material No. Standard Closest ASTM equivalentC22+N 1.0402+N EN 10083 A 576 Grade 1020
Cast stainless steel,hard-faced
GX5CrNiMo19–11–Colm.6 1.4408–Colm.6 - A 743 Grade CF8M–Colm.6
Coating and preservation
▪ Coating and preservation to KSB standard
Product benefits
▪ Double volute from DN 80 (3 inch) for low radial thrust
▪ Easy to service thanks to back pull-out design
▪ Heatable casing covers optionally available for high-temperature applications
▪ Wide variety of flanges to all standards up to PN 100equivalent (ASME Class 600)
▪ Dimensioned for longer service life than specified by API610, reducing maintenance expenditure and work
▪ Individual adjustment of axial thrust balancing formaximum bearing life
▪ "Low Nss hydraulic systems" (inducer on option) foroptimum selection to API
Acceptance tests / Warranties
▪ Materials testing
– Test report 2.2 on request
– Test report 3.1 on request
▪ Final inspection
– Inspection certificate 3.1 to EN 10204 on request
▪ Hydraulic test
The operating point of each pump is warranted accordingto ISO 9906/2B.
The following acceptance tests may be performed andcertified at extra charge:
– Performance test to ISO 9906
– Performance test to API (API 610)
– NPSH test
▪ Other tests (e.g. vibrations, strength) on request.
▪ Warranty
Warranties are given within the scope of the valid deliveryconditions.
Pressure and temperature limits
Average values – the values of individual pump sizes may behigher or lower than the values indicated. (Contact KSB!)
Mag-drive PumpsProcess Pumps
RPHmdp 7
Fluid temperature t [°C]
Perm
issi
ble
pu
mp
pre
ssu
re p
[b
ar]
0
10
20
30
40
50
60
70
80
90
100
110
120
-50 0 50 100 150 200 250 300 350 400 450
A487 Gr. CA6NM
A351 Gr. CF3M / CF8M
A 216 Gr. WCB
A351 Gr. 1B
A217 Gr. CA15
A
Pressure and temperature limits of pump
A Pressure limit of the magnetic coupling7)
Sizes
Nominal impeller diameters available
Nominaldiameter ofthedischargenozzle
Nominal impeller diameter
180 181 230 231 280 281 360 361 450
25 ✘ - ✘ - - - - - -40 ✘ ✘ ✘ ✘ ✘ ✘ - ✘ -50 ✘ - ✘ - ✘ - ✘ - ✘80 ✘ - ✘8) - ✘8) - ✘8) - ✘8)
100 ✘ - ✘8) - ✘8) - ✘8) - ✘8)
Suitable bearing brackets
Nominaldiameter ofthe dischargenozzle
Nominal impeller diameter
180 181 230 231 280 281 360 361 450
25 M01 - M01 - - - - - -40 M01 M01 M01 M01 M01 M01 - M01/M02 -50 - - - - M01/M02 - M02 - M0280 - - - 8) - M028) - M028) - M028)
100 M01/M02 - M028) - M028) - M028) - M028)
7) Higher pressures on request8) Casing with double volute
Mag-drive PumpsProcess Pumps
8 RPHmdp
Technical data
Bearing brackets M01-M02Si
ze
Bea
rin
g b
rack
et
Impeller Shaft diameter Drive
At bearings
At
cou
plin
g
P/n
val
ue
Max. drive power at
Imp
elle
r o
utl
etw
idth
Imp
elle
r in
let
dia
met
er Imp
elle
rd
iam
eter
Pum
p e
nd
Dri
ve e
nd
n =
145
0 rp
m
n =
175
0 rp
m
n =
290
0 rp
m
n =
350
0 rp
m
Max. Min.
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [kW] [kW] [kW] [kW]
25-180 M01 / M02 6 48 179 120 55 45 32 0,0226 32,77 39,55 65,54 79,1025-230 6 48 224 180 55 45 32 0,0226 32,77 39,55 65,54 79,1040-180 6 58 180 130 55 45 32 0,0226 32,77 39,55 65,54 79,1040-230 6,2 57 224 1 55 45 32 0,0226 32,77 39,55 65,54 79,1040-181 7,8 75 180 130 55 45 32 0,0334 48,43 58,45 96,86 116,9040-231 7,7 75 230 180 55 45 32 0,0334 48,43 58,45 96,86 116,9040-280 7,5 61 278 220 55 45 32 0,0334 48,43 58,45 96,86 116,9040-281 7,7 71 278 230 55 45 32 0,0334 48,43 58,45 96,86 116,9040-361 7,9 69 343 280 55 45 32 0,0334 48,43 58,45 96,86 116,9050-180 10,9 88 180 140 55 45 32 0,0334 48,43 58,45 96,86 116,9050-230 10 95 230 180 65 55 42 0,0675 97,88 118,13 195,75 236,2550-280 9,6 93 286 230 65 55 42 0,0675 97,88 118,13 195,75 236,2550-360 9,6 88 343 280 65 55 42 0,0675 97,88 118,13 195,75 236,2550-450 10 87 430 340 65 55 42 0,0675 97,88 118,13 195,75 236,2580-180 17 110 190 140 65 55 42 0,0675 97,88 118,13 195,75 236,2580-230 14 113 235 190 65 55 42 0,0675 97,88 118,13 195,75 236,2580-280 12,5 110 286 230 65 55 42 0,0675 97,88 118,13 195,75 236,2580-360 11,5 111 350 280 65 55 42 0,0675 97,88 118,13 195,75 236,2580-450 M02 12 110 430 350 80 75 60 0,2141 311,32 375,73 622,63 751,45100-180 M01 / M02 28 133 190 150 65 55 42 0,0675 97,88 118,13 195,75 236,25100-230 22,3 128 235 190 65 55 42 0,0675 97,88 118,13 195,75 236,25100-280 17,8 130 295 230 65 55 42 0,0675 97,88 118,13 195,75 236,25100-360 M02 15,5 136 355 295 80 75 60 0,2141 311,32 375,73 622,63 751,45100-450 M02 14,5 140 440 355 80 75 60 0,2141 311,32 375,73 622,63 751,45
Mag-drive PumpsProcess Pumps
RPHmdp 9
Selection charts
RPHmdp, n = 2900 rpm
KE1316.4052/6
5 10 20 30 40 50 100 200 300 400 500 1000 2000 3000 4000 5000US.gpm
4 5 10 20 30 40 50 100 200 300 400 500 1000 2000 3000 4000IM.gpm
0.3 0.4 0.5 1 2 3 4 5 10 20 30 40 50 100 200 300l/s
1 2 3 4 5 10 20 30 40 50 100 200 300 400 500 1000Q[m /h]3
40
50
100
200
300
400
500
ft
20
30
40
50
100
200
300
12
H[m]
100-180
100-230
100-280
100-230B
100-180B
100-360A
100-280B
80-230
100-360C
80-180
80-230B
80-180B
50-230
50-180
100-450
80-360
80-28050-280
80-45050-450
50-360
40-361
40-28140-280
40-23140-230
40-18140-180
25-230
25-180
Mag-drive PumpsProcess Pumps
10 RPHmdp
RPHmdp, n = 1450 rpm
5
4 5
25-230
25-18040-180
40-230
40-280
40-231
40-181
40-281
40-361
50-450
50-360
50-280
50-230
50-18080-180B
80-230B
80-230
100-450
100-360A100-360C
100-280B
100-230100-230B
100-180B
100-180
80-280
80-180
80-360
80-450
10
10
ft
10
20
20
20
30
30
30
40
40
50
50
100
100
200
200
300
300
400
400
500
500
1000
1000 2000 3000 4000
20
20
10
10Q[m3/h]
5
5
4
4
3
3
2
2
l/s1
1
0.50.40.3
30
30
40
40
40
50
50
50
100
100
100
200
200
200200
50
40
30
20
10
5
4H
[m]3
100
300
300
300
400
400
400
500
500
500
1000
1000
2000
2000
3000
3000
4000
4000
US-gpm
IM-gpm
10000
10000
20000
RPHmdp, n = 3500 rpm
KE1316.4062/4
5 10 20 30 40 50 100 200 300 400 500 1000 2000 3000 4000 5000US.gpm
4 5 10 20 30 40 50 100 200 300 400 500 1000 2000 3000 4000IM.gpm
0.3 0.4 0.5 1 2 3 4 5 10 20 30 40 50 100 200 300l/s
1 2 3 4 5 10 20 30 40 50 100 200 300 400 500 1000Q[m /h]3
100
200
300
400
500
ft
20
30
40
50
100
200
300
H[m]
100-180
100-230
100-280B
100-230B
80-230
100-180B
80-230B
80-180
80-180B
100-280
100-360A100-360C
80-360
80-280
50-360
50-280
50-230
50-18040-181
40-361
40-281
40-280
40-231
40-230
40-180
25-230
25-180
Mag-drive PumpsProcess Pumps
RPHmdp 11
RPHmdp, n = 1750 rpm
5
4 5
25-230
25-180 40-180
40-230
40-280
40-231
40-181
40-281
40-361
50-450
50-360
50-280
50-230
50-180
80-180B
80-230B
80-230
100-450
100-360C 100-360A
100-280B
100-230
100-230B
100-230
100-280
100-180B
80-280
80-230
80-180
80-360
80-450
10
ft
10
20
20
20
30
30
30
40
40
50
50
100
100
200
200
300
300
400
400
500
500
1000
1000 2000 3000 4000 6000
20
20
10
10Q[m3/h]
5
5
4
4
3
3
2
2
l/s1
1
0.50.40.3
30
30
40
40
40
50
50
50
100
100
100
200
200
200
200
300
50
40
30
20
10
5
4
H
[m]
100
300
300
300
400
400
400
500
500
500
1000
1000
2000
2000
3000
3000
4000
4000
US-gpm
IM-gpm
10000
10000
20000
20000
Dimensions and connections
Dimensions
Pump dimensions
4) Extended shaft on requestI Middle of pump footII Middle of DN1, shaft
Pump dimensions
Size Bearingbracket
Weight[kg]
Pump dimensions
DN1 DN2 a c c’ e f f’ g1 h2 m1 n1 n3 n6 r
25-180 M01/M02 116 40 25 120 736 771 105 616 651 40 230 130 420 320 0 18525-230 M01/M02 131 40 25 120 736 771 125 616 651 40 255 130 460 360 0 20540-180 M01/M02 122 50 40 130 746 781 105 616 651 40 250 130 420 320 0 18840-181 M01/M02 136 50 40 130 750 785 110 620 655 40 250 130 420 320 0 198
Mag-drive PumpsProcess Pumps
12 RPHmdp
Size Bearingbracket
Weight[kg]
Pump dimensions
DN1 DN2 a c c’ e f f’ g1 h2 m1 n1 n3 n6 r
40-230 M01/M02 138 50 40 130 746 781 130 616 651 40 265 136 460 360 0 21540-231 M01/M02 158 50 40 140 760 795 135 620 655 40 265 146 460 360 0 22040-280 M01/M02 197 50 40 140 760 795 160 620 655 40 290 146 540 440 0 23840-281 M01/M02 195 50 40 140 760 795 160 620 655 40 290 150 540 440 0 24840-361 M01/M02 249 50 40 150 770 805 195 620 655 40 305 150 640 540 0 27550-180 M01/M02 153 80 50 150 770 805 120 620 655 50 265 150 470 360 0 22050-230 M01/M02 240 80 50 155 885 915 140 730 760 50 265 150 510 400 0 23050-280 M01/M02 289 80 50 170 900 930 170 730 760 50 290 150 550 440 0 25550-360 M01/M02 347 80 50 170 900 930 200 730 760 50 310 150 650 540 0 28550-450 M01/M02 441 80 50 180 910 940 245 730 760 50 365 150 750 640 0 32580-180 M01/M02 242 100 80 175 920 950 140 745 775 60 290 170 510 400 0 23580-230 M01/M02 264 100 80 170 900 930 160 730 760 60 290 170 550 440 20 26580-280 M01/M02 317 100 80 180 910 940 180 730 760 60 300 170 590 480 20 29080-360 M01/M02 361 100 80 190 920 950 210 730 760 60 310 170 650 540 15 32580-450 M02 547 100 80 200 1040 1082 260 840 882 60 370 170 760 650 20 375100-180 M01/M02 289 150 100 185 930 960 170 745 775 70 325 190 590 480 25 275100-230 M01/M02 303 150 100 170 900 930 175 730 760 70 325 170 590 480 30 285100-280 M01/M02 345 150 100 170 900 930 200 730 760 70 335 190 650 540 30 315100-360 M02 477 150 100 200 1040 1082 225 840 882 70 355 190 730 590 25 340100-450 M02 576 150 100 210 1050 1092 270 840 882 70 385 190 860 720 30 395
Dimensions of shaft end and foot bolts
Size Bearingbracket
Shaft end Foot bolts
d1 l l' t u y i1 m2 n2 s1
25-180 M01/M02 32 80 115 35 10 140 30 60 380 17,525-230 M01/M02 32 80 115 35 10 140 30 60 420 17,540-180 M01/M02 32 80 115 35 10 140 30 60 380 17,540-181 M01/M02 32 80 115 35 10 140 30 60 380 17,540-230 M01/M02 32 80 115 35 10 140 30 60 420 17,540-231 M01/M02 32 80 115 35 10 140 30 60 420 17,540-280 M01/M02 32 80 115 35 10 140 35 70 500 17,540-281 M01/M02 32 80 115 35 10 140 35 70 500 17,540-361 M01/M02 32 80 115 35 10 140 35 70 600 17,550-180 M01/M02 32 80 115 35 10 140 35 70 420 2250-230 M01/M02 42 110 140 45 12 140 35 70 460 2250-280 M01/M02 42 110 140 45 12 140 35 70 500 2250-360 M01/M02 42 110 140 45 12 140 45 90 600 2250-450 M01/M02 42 110 140 45 12 140 45 90 700 2280-180 M01/M02 42 110 140 45 12 140 45 90 460 2280-230 M01/M02 42 110 140 45 12 140 45 90 500 2280-280 M01/M02 42 110 140 45 12 140 45 90 540 2280-360 M01/M02 42 110 140 45 12 140 45 90 600 2280-450 M02 60 140 182 64 12 180 45 90 710 22100-180 M01/M02 42 110 140 45 12 140 50 100 540 26100-230 M01/M02 42 110 140 45 12 140 50 100 540 26100-280 M01/M02 42 110 140 45 12 140 50 100 600 26100-360 M02 60 140 140 64 18 180 55 110 670 26100-450 M02 60 140 182 64 18 180 55 110 800 26
Connections
Connection types
Connection ≤ DN 50 ≥ DN 80 Description1M NPT 1/2-14 NPT 1/2-14 Pressure gauge5B NPT 1/2-14 NPT 1/2-14 Vent6B DN15 ASME B16.5 Fluid drain7E.1/A.1 NPT 1/2-14 NPT 1/2-14 Cooling liquid IN/OUT12A.1 NPT 1/2-14 NPT 1/2-14 Circulation liquid IN/OUT12A.2 NPT 1/2-14 NPT 1/2-14 Circulation liquid IN/OUT13B NPT 1/2-14 NPT 1/2-14 Oil drain13D NPT 1/2-14 NPT 1/2-14 Vent plug638 NPT 3/8-18 NPT 3/8-18 Constant level oiler
Mag-drive PumpsProcess Pumps
RPHmdp 13
General assembly drawing with list of components
562.01 412.02
344
391.01 818.01 914.04 920.05 914.03900.03931.03 562.03
360.02400.02 322
411.01 562.02314.01 818.02 314.02 931.02 82-15 145 412.01 423.02 913.01
940.01210
423.01
360.01400.01
902.03920.03
330 320506.01 920.01
931.01 901.01
902.01920.01 914.01
902.02920.02 523.01
940.02 901.02940.03
102
502.02904.02
230
502.01904.01
940.04
922.01
503.01904.03
503.02904.04
724.01
902.04920.04
411.02
512
161 506.02
914.02
General assembly drawing
List of components
Part No. Comprising Description102 102 Volute Casing
502.01 Casing wear ring904.01 Grub screw411.01 /.02 Joint ring724.01 Blind flange920.01/.04 Hexagon nut902.01/.04 Stud
145 145 Adapter914.03 Socket head cap screw901.03 Hexagon head bolt931.03 Lock washer
161 161 Casing cover502.02 Casing wear ring412.01/.02 O-ring562.02 Parallel pin902.02 Stud920.02 Hexagon nut904.02 Grub screw
210.01 210.01 Shaft, drive-end940.01 Key920.01 Hexagon nut931.01 Lock washer940.02 Key
210.02 210.02 Shaft, pump-end562.01 Parallel pin
Mag-drive PumpsProcess Pumps
14 RPHmdp
Part No. Comprising Description940.03/.04 Key931.02 Lock washer920.05 Hexagon nut922.01 Impeller nut
230 230 Impeller503.01/.02 Impeller wear ring904.03/.04 Grub screw
330 330 Bearing bracket6429) Oil level sight glass913.02 Vent plug6389) Constant level oiler
7209) Fitting
916.469) Plug322 Cylindrical roller bearing506.01/.02 Retaining ring320 Deep-groove ball bearing
344 344 Bearing bracket lantern512 Wear ring902.03 Stud920.03 Hexagon nut562.02 Parallel pin
360.01 360.01 Bearing cover, external901.01 Hexagon head bolt400.01 Gasket423.01 Labyrinth ring
360.02 360.02 Bearing cover, internal901.02 Hexagon head bolt400.02 Gasket423.02 Labyrinth ring
82-15 82-15 Containment shroud82-19 82-19 Magnetic element
818.01 Inner rotor818.02 Outer rotor
847 847 Magnetic coupling99-11 99-11 Bearing
391.01 Bearring ring carrier314.01/.02 Thrust bearing523.01 Shaft sleeve914.01/.02/.04 Socket head cap screw
9) not shown in drawing
Mag-drive PumpsProcess Pumps
RPHmdp 15
1316
.57/
01-EN
04.0
9.20
13
KSB Pumps and Valves (Pty.) Ltd Cor. North Reef & Activia Roads, Activia Park: 1401 Germiston (Johannesburg)Republic of South AfricaTel. +27 (11) 876 5600Fax +27 (11) 822 2013E-Mail: sales@ksbpumps.co.za