Post on 30-Dec-2019
transcript
SACE Tmax XT
ABB
XT2 - XT4
Ekip Din Rail Cartridge - XT2 - XT4Ekip Din Rail Cartridge - XT2 - XT4
Doc. N.° 1SDH002009A1503 - ECN000090389 - Rev. A
XT2 XT4
A
B
C
DIN RailCartiridge
one module
1
DIN RailCartiridge
1
11
1
2
SACE Tmax XT | ABB
3
4
SACE Tmax XT | ABB
Mandatory Ekip Supply
5
6
SACE Tmax XT | ABB
C
To be connected in presence of Ekip COM
7
8
SACE Tmax XT | ABB
Connect to Ekip COM if present
9
10
SACE Tmax XT | ABB
XT2 - XT4 F
XT2 - XT4 F
2,0 ÷ 2,2lb in
0,22 ÷ 0,25Nm
See cable marking
11
12
SACE Tmax XT | ABB
XT2 - XT4 W
XT2 - XT4 W
OPTIONAL
See 1SDH000713R0601
13
14
SACE Tmax XT | ABB
XT2 - XT4 W
XT2 - XT4 W
15
16
SACE Tmax XT | ABB
"CLACK"
Eki
p D
IN R
ail
Ca
rtrid
ge
Ba
sic
V5
Ekip DIN Rail Cartridge Basic
* M)
75
XCT1 K2 K1 W3 W4
Eki
p D
IN R
ail
Ca
rtrid
ge
Ekip DIN Rail Cartridge
* M)
76
XCT2 1 41 4
IN ALTERNATIVA TRA DI LORO
AS IN ALTERNATIVE TO EACH OTHER
K2 K1 W3 W4
17
18
Guida EN 50022 secondo norme DIN 43880EN 50022 guide according to DIN 43880 standardProfilschiene EN 50022 gemäß DIN 43880Glissière EN 50022 selon normes DIN 43880Guia EN 50022 segun normas DIN 43880Guida EN 50022 secondo norme DIN 43880
63 (2.48")
90 (3
.548")
90 (3
.548")
106.2 (4.18") 64.5 (2.54")
2 SLOT 4 SLOT
Ekip Supply +
1 external module
Ekip Supply +
3 external modules
SACE Tmax XT | ABB
19
© Copyright 2013-2018 ABB. All rights reserved. www.abb.com ABB
1
2
3
- Fornire alimentazione all’Ekip Supply- Abilitare il bus locale, da Display -> Impostazioni -> Moduli -> Local bus -> ON- Verificare l’accensione dei led sul modulo (1), sull’Ekip Supply (2) e sullo sganciatore (3)- Se il led dei moduli lampeggia in modo asincrono rispetto a quello dello sganciatore, consultare il manuale dell’interruttore.
- Supply power to the Ekip Supply- Enable the local bus, by Display -> Settings -> Modules -> Local bus -> ON- Check that the leds are lit on the module (1), on the Ekip Supply (2) and on the release (3)- If the led of the modules flashes asynchronously in relation to that of the release, consult the circuit-breaker manual.
- Ekip Supply mit Speisung versorgen- Aktivieren Sie den lokalen Bus, mit Anzeige -> Einstellungen -> Module -> Local Bus -> ON- Prüfen, ob die led auf dem Modul (1), auf Ekip Supply (2) und dem Auslöser (3) an sind.- Wenn die led von Modulen asynchron im Bezug zu der des Auslösers aufblinkt, im Handbuch des Leistungsschalters nachlesen.
- Fournir l'alimentation à l’Ekip Supply- Activer le bus local, par affichage -> Paramètres -> Modules -> bus local -> ON- Vérifier l'allumage des voyants sur le module (1), sur l’Ekip Supply (2) et sur le déclencheur (3)- Si le voyant de les modules clignote de manière asynchrone par rapport à celui du déclencheur, consulter le manuel du disjoncteur.
- Dar alimentación al Ekip Supply- Habilitar el autobús local, por Pantalla -> Configuración -> Módulos -> bus local -> ON- Verificar el encendido de los led en el módulo (1), en el Ekip Supply (2) y en el relé (3)- Si el led del los módulos parpadea en modo asíncrono respecto al led del relé, consultar el manual del interruptor.
- Fornire alimentazione all’Ekip Supply- Abilitare il bus locale, da Display -> Impostazioni -> Moduli -> Local bus -> ON- Verificare l’accensione dei led sul modulo (1), sull’Ekip Supply (2) e sullo sganciatore (3)- Se il led dei moduli lampeggia in modo asincrono rispetto a quello dello sganciatore, consultare il manuale dell’interruttore.