Post on 13-Sep-2020
transcript
Same Look. Same Installation.
New Technology.It’s all about efficiency. The MagForce™ High Efficiency
Motor System offers a 90% motor efficiency rating,
which is up to 12% higher than traditional submersible
motor designs. With permanent magnet technology,
you can now offer an investment payback of less
than 2 years in most long- or continuous-run
applications*. They get a trusted product,
you become their solution provider.
*Results based on field trial data.
franklinwater.com
GROUNDBREAKING EFFICIENCY90% efficiency rating is 10-12% greater than standard induction motor construction. Typical high-duty rate systems can have a payback* of 1 to 2 years. * Field trial data.
SIMPLIFIED INVENTORY MANAGEMENTThree motor sizes cover pump horsepowers ranging from 7.5 to 60. Fewer SKUs simplify your inventory.
SMALLER FOOTPRINTLighter and easier to handle than standard induction motors and, like all submersible motor systems, provides a smaller above ground footprint when compared to line shaft turbines.
HORSEPOWER BOOSTCapable of a 13.6% horsepower boost achieved by increasing the motor’s shaft speed to a true 60 hertz, 3600 rpm**. This allows increased pump output in terms of water volume and total dynamic head pressure without having to pull the system from the well.** Not to exceed the PM motor’s max amp rating.
FEATURES & BENEFITS
A PACKAGED DEALWhen ordered, the motor is shipped with a customized variable frequency drive panel that is preprogrammed for use with a transducer-controlled pump system. This allows simple startup, compatibility with a variety of application types, and is guaranteed to optimize performance and maximize system life. The drive control panel also features real-time monitoring, protection, and customizable application-specific programming software as needed to cover all customer requirements.
SLASH ELECTRICITY CONSUMPTIONSince the motor has rare earth magnets, there is less electrical energy loss, which translates into greater power output per dollar spent on power input. This saves operational costs every time the motor is run; the more it is used, the more can be saved.
FULLY SUPPORTEDComes fully supported by the industry’s leading Technical Support professionals and Field Service Engineers.
= Unique to the Franklin Electric Experience
0 $2,500 $5,000 $7,500 $10,000 $12,500 $15,000 $17,500 $20,000 $22,500 $25,000
7.5
10
15
20
25
30
40
50
60
MOT
OR H
ORSE
POW
ER
COST SAVINGS OVER TIME
$1,970
$3,415
$4,730 $7,883
$4,989 $8,315
$5,759 $9,599
$7,716 $12,861
$12,596 $20,993
$14,313
$14,350$4,783
$4,199
$1,920
$1,663
$1,577
$1,138
$657
$2,572
$4,771 $23,856
$23,916
$5,691
$3,283 89% EFFICIENT (vs. 80% for Induction Motor)
92% EFFICIENT (vs. 81% Ind.)
91% EFFICIENT (vs. 82% Ind.)
91% EFFICIENT (vs. 83% Ind.)
91% EFFICIENT (vs. 83% Ind.)
91% EFFICIENCT (vs. 79% Ind.)
92% EFFICIENT (vs. 83% Ind.)
92% EFFICIENT(vs. 84% Ind.)
92% EFFICIENT(vs. 82% Ind.)
After 1 Year
After 3 Years
After 5 Years
KEY
OPERATION COST SAVINGS
The MagForce™ Permanent Magnet Motor System is the smarter choice over line shaft turbine systems and standard submersible induction motors. Here’s why…
• Unlike turbine systems, no line shaft, bearings, or pedestal is needed
• Compact motor provides reduced bearing loads and increased reliability
• Obtain the same HP and pump output in a simplified, compact package
• Results in lower installation and maintenance costs
Shaft
Shaft Bearing
ElectricalSupply
Pump
Motor
Inlet
Impellers
Motor
Housing
Mounting
Drive Shaft
Shaft
Shaft Bearing
ElectricalSupply
Pump
Motor
Inlet
Impellers
Motor
Housing
Mounting
Drive Shaft
LINE SHAFT TURBINEMAGFORCE™ VS
* Based on electric costs of $0.10 USD/kwh running at 100% duty.** Efficiencies generated by Franklin Electric lab tested date.
MOTOR TYPE MagForce™ Line Shaft Submersible Induction
SIZE
COST
NOISE
MAINTENANCE
EFFICIENCY
PERFORMANCE
GOOD: BETTER: BEST:
A SMARTER CHOICE
Mi9046 04-19
POWER DENSITY
Obtain the same HP and pump output in a simplified, compact package. Compare the physical size of the MagForce™ and standard submersible induction systems in the chart below:
Motor MagForce™ Induction
HP Length Weight Length Weight7.5
25" 105 lbs24.2" 108 lbs
10 25.4" 116 lbs15 28" 129 lbs20
31.2" 126 lbs30.6" 145 lbs
25 33.1" 156 lbs30 35.7" 174 lbs40
39.8" 156 lbs40.8" 202 lbs
50 55.3" 300 lbs60 61.3" 330 lbs
Eric McElroy | Co-Owner of Irrigation Pumps and Power, Inc.
I just thought it was a no-brainer to get these out in the field. The most intriguing part is the fact that it’s 10–12 percent more efficient. Energy savings you will attain should pay for itself within a year.”
IDEAL FOR LONG-RUN APPLICATIONS
• Groundwater remediation
• Drainage water level control
• Municipal/Utility water supply
• Construction site dewatering
• High volume and industrial livestock operations
• Mine site dewatering and tank level control
• Well supply geothermal HVAC systems
• Pivot irrigation systems
“
Mi9046 04-19