Post on 10-Apr-2018
transcript
8/8/2019 Set Up Winvnc
1/37
VNC 4Enterprise Server
User Guide
8/8/2019 Set Up Winvnc
2/37
indexfurther informationusing vnc server 4introduction installation configuration2page
Contents
Introduction 3
What are VNC Server and Viewer? 3
Getting started 3
Installation 4Making a standard installation 4
Service mode registration 4
Configuration 5
Customising VNC Server 4 5
Where maximum security is required 5
Where speed is the most important factor 6
Where the server is being demonstrated to a group 6
Using VNC Server 4 7
Starting and stopping VNC Server 4 7
Starting and stopping in user-mode 7
Connecting to (and from) VNC Server 4 7
Starting and stopping in service-mode 8
Further information 9
Options when installing 10
Using the tray icon 12Connection management 12
Enabling guest login 12
VNC Server Properties 13
Displaying VNC Server Properties 13
Security 14
Connections 16
Inputs 17
Sharing 18
Desktop 19
Capture Method (Hooks) 20
Legacy 21
VNC Extended authentication 22NT Logon authentication 23
Two modes of operation 24
User mode 24
Service mode 24
Listening viewer (server-initiated connection) 25
Access control: Allow, deny or query addresses 26
Calculating a range mask for access control 27
Ordering entries in the access control list 28
Dealing with firewalls 29
Changing VNC ports 29
What is an IP address? 30
What is a Subnet mask? 31
How a subnet mask actually works 31
What is a port? 32
VNC authentication and encryption 33
Windows version support 34
Troubleshooting 35Support 36
Via the web 36
Acknowledgements 36
Index 37
8/8/2019 Set Up Winvnc
3/37
indexfurther informationusing vnc server 4introduction installation configuration3page
Introduction
What are VNC Server and Viewer?VNC offers a deceptively simple service - it allows you to v iew and control a remote system as
though seated next to it, wherever you are.
The compact VNC Server 4 application runs on the system to be controlled. Meanwhile, con-
necting systems can either run the VNC Viewer application or, use a standard web browser todownload and use a Java viewer from the server system.
VNC adapts itself automatically and dynamically to varying conditions, including differing
screen contents and network bandwidths. VNC is also platform-independent and will hap-pily allow a Windows system to control a Linux server, or vice versa.
VNC Server 4 provides main two modes of operation to suit the manner in which the serversystem will be used and accessed. Please see Two modes of operation for details.
Thanks to a comprehensive update VNC now also offers:
Full user and server authentication,
Secure link encryption,
Server screen scaling to fit any window size.
Integrated connection management.
File transfer.
Getting startedThis guide provides information on various aspects of installing,configuring and using VNC Server 4
Installation
Making a standard installation Service mode registration
Configuration
Tips on customising VNC Server 4 for different situations
Using VNC Server 4
Connecting to (and from) the serverHow to start and stop VNC Server 4
Further informationOptions when installingUsing the tray iconVNC Server propertiesNT Logon authenticationTwo modes of operation: User and Service
Listening viewerAccess control: Allow, deny or query addressesFirewallsWhat is an IP address?What is a subnet mask?What is a port?Windows version supportTroubleshootingSupport
VNC breaks the Server screen image
down into constituent parts and trans-
mits them to the Viewer.
Controlling mouse movements and key
press inputs from the Viewer are sent to
the Server.
8/8/2019 Set Up Winvnc
4/37
indexfurther informationusing vnc server 4introduction installation configuration4page
Installation
Making a standard installationVNC was designed from the outset to be efficient and compact in operation and suchqualities also apply to its installation. VNC Server 4 is available as a self-extracting installer
downloaded from the RealVNC website.
To install VNC Server 4
1 Run the downloaded self-extracting installer and follow the on-screen prompts.
For the majority of installations it should be possible to choose all of the default optionsat almost every stage. At certain points you may be asked to enter a password and a validlicense key.
Please refer to the Options when installing section for details about any part of theinstallation procedure.
If you choose all of the default options, then your VNC Server 4 installation will be asfollows:
Operation mode: Service-Mode
Configuration: VNC Authentication
Encryption: Always On
Connection port: 5900
Dormant VNC Server 4 icon within the system tray - this indicates
that the server is running but not currently actively connected
Status: Running and ready to receive connections:
File location: C:\Program Files\RealVNC\VNC4
Service mode registrationDuring installation, if you chose not to Register and configure VNC Server for Service-Modethen VNC Server can subsequently be registered for use in Service-Mode via the Start Menu
option. Once registered, VNC Server will automatically run every time the computer isswitched on, even before any users have logged on.
When it is no longer needed as a system serv ice, you can unregister VNC Server at any time.
To register service mode
1 Click the Windows Startbutton. Choose All Programs(or Programsin non-XP versions).
Select the RealVNCentry, then VNC Server 4 (Serv ice-Mode)and finally select RegisterVNC Service.
VNC Server 4 serv ice mode will be registered within Windows and a confirmation message
should be displayed. When you next boot up the system, VNC Server 4 will automaticallystart as a system serv ice. Alternatively, VNC Server can be started immediately by selecting theStart VNC Service menu item.
To unregister service mode
1 Click the Windows Startbutton. Choose All Programs(or Programsin non-XP versions).Select the RealVNCentry, then VNC Server 4 (Serv ice-Mode)and finally select UnregisterVNC Service.
VNC Server 4 service mode registration will be removed and a confirmation message should
be displayed. Although VNC Server 4 will continue to operate for the moment, when you nextboot up the system, it w ill not automatically start. VNC Server can be stopped immediately byselecting the Stop VNC Service menu item (see below).
To stop the VNC Server 4 immediately, either:
Select the Stop VNC Serviceoption within the same Startmenu folder as mentioned
above, or
Right click on the VNC Server icon in the system tray to display a popup menu. Select
the Close VNC Serveroption.Note that on Windows NT-based systems, to stop the VNC Server you must be logged on asa member of the Administrators security group.
In either case, a confirmationdialog will be displayed:
Click the Yesbutton to proceed.
8/8/2019 Set Up Winvnc
5/37
indexfurther informationusing vnc server 4introduction installation configuration5page
Configuration
Customising VNC Server 4VNC Server 4 operates perfectly well using its default installation options. However, by mak-
ing various changes it is possible to optimise VNC Server operation for particular situations.The types of uses covered in this chapter are:
Where maximum security is required - see below
Where speed is the most important factor
Where the server is being demonstrated to a group
All changes are made using the VNC Server Properties page. See Displaying VNC ServerProperties for details about how to access it.
Where maximum security is requiredThere are numerous VNC Server 4 settings on various tabs that affect security and it is worthensuring that they are all configured correctly when security is of particular issue.
Security tab [see Securityfor all options]
In order to create a secure server system, the most crucial settings to consider are Encryption
and Authentication. The configurations of these two settings conspire to determine the ro-bustness of your server system and its connections.
Wherever possible the Encryption setting should be set to Always On. The only real draw-back here is that users with older legacy viewers will be unable to make a connection (thebest remedy is to upgrade such users to VNC Viewer 4 or above).
With Encryption set to Always On, you can choose to use either type ofAuthentication:VNC Password or NT Logon. The latter is recommended because it uses the native Win-dows security system and allows you to allocate different access rights to users or groups of
users. Note: NT Logon Authentication cannot be used with servers on Windows 95, 98 or Me.
If you must support legacy users, then set Encryption to Prefer On and select VNC Pass-word Authentication. Note that legacy viewers will be authenticated using only the first
eight characters of a password. Also, legacy viewers do not support encryption and will
not authenticate the server. Consider redressing the balance using Access Control(withinthe Connectionstab) to restrict access to specific IP addresses.
If a user will be present at the server system, you may wish to manually approve each con-nection. If so, tick the Prompt local user to accept connections. Exceptions may be made forparticular privileged users by granting them the Connect without querying local userrightin the NT Logon configuration dialog.
Unless you need it, you can prevent users from enabling the guest login by setting Guestlogin accessto None.
Sharing tab [see Sharing for all options] If one remote user should not be observable by another, select the Never treat new connec-
tions as sharedoption.
If the existing user should retain precedence over new users, untick the Non-shared connec-tions replace existing onesoption.
Connections tab [see Connections for all options] Ports- Consider combining the main access port (Accept connections on port) and the Serve
Java viewer...port to use the same number. This will mean that only one port needs to beopened through a firewall. Combining the ports will cause each initial connection to takeup to two seconds longer to complete. See Dealing with firewalls for details.
Disconnect idle clients- Reduce the idle time to help ensure that abandoned connectionsare not abused at the users system.
Access control- Where possible define the IP addresses from which connections will be ac-cepted and deny access to all others. See Access control for details.
See also Listening viewer for details about how to avoid opening any new firewall ports byusing the server to initiate connections to each viewer.
Inputs tab [see Inputs for all options] Clipboard updates- To prevent sensitive files or data on the local clipboard being accessible
remotely or vice versa, untick the Accept clipboard updates from clients, the Send clipboardupdates to clients, the Accept files from clientsand the Send files to clientsoptions.
Allow ... events- In situations where users need to view but not interact with the server,you can untick the pointer and keyboard events options. When using NT Logon authenti-cation, you can also untick various rights within the NT Logon configuration dialog.
Desktop tab [see Desktop for all options] When last client disconnects- If the system is to be locally unattended and there is a chance
of it being accessed by passers by, select the Lock workstation option to ensure that thesystem is not left open following a remote session.
Legacy tab [see Legacyfor all options] Ensure that the Only use protocol version 3.3 option is not ticked. This option forces
the server into a compatibility mode that does not support advanced authentication or
encryption features.
8/8/2019 Set Up Winvnc
6/37
indexfurther informationusing vnc server 4introduction installation configuration6page
Where speed is the most important factorThe speed of response is affected by several factors.
Security tab [see Securityfor all options] Encryption - The use of data encryption imposes small performance overheads. Where
the threat of data interception is not a strong issue, the Encryption option could be set to
Prefer Off. VNC Viewers select Let Server Chooseas standard for their encryption setting,so the link will be unencrypted unless a viewer explicitly requests an encrypted session.
Connections tab [see Connections for all options]
Ports- Combining the main access port (Accept connections on port) and the Serve Javaviewer... port to use the same number lengthens the initial connection time by up to two
seconds. Where possible, ensure that these options are set to use different port numbers.
Desktop tab [see Desktop for all options] While connected- All three of the options in this section affect response speed. All should
be ticked to reduce the information needed to be sent to the viewer.
Where the server is being demonstrated to a groupThere are a number of areas where small changes may make VNC Server 4 even more suitablefor demonstration purposes.
Connections tab [see Connections for all options] Disconnect idle clients after- Ensure that the value set here will not affect viewers who are
observing a server demonstration but not necessarily responding to it.
Inputs tab [see Inputs for all options] Accept events- Depending on the type of demonstration, it may be advantageous to pre-
vent the viewers from controlling the system. If so, untick both the Accept pointer eventsfrom clientsand the Accept keyboard events from clientsoptions in order to retain control.
Sharing tab [see Sharing for all options] If multiple viewers must be simultaneously connected, obviously there must be some ele-
ment of sharing. Select the Always treat new connections as sharedoption and, as a pre-caution against certain viewer configurations, untick the Non-shared connections replaceexisting onesoption.
Desktop tab [see Desktop for all options] While connected- Deselecting all three of the options within this section can help to im-
prove performance. However, will the loss of the background pattern or wallpaper detractfrom the demonstration?
Listening viewer
In addition to the above settings, a very useful feature when demonstrating is to use theListening viewerfeature. This allows the server user to initiate connections to one or more
viewers, relieving the users of this task. To achieve this, each VNC viewer application must betold to listen for connection attempts. See Listening viewer for more details.
8/8/2019 Set Up Winvnc
7/37
indexfurther informationusing vnc server 4introduction installation configuration7page
2 Select the RealVNCentry, then VNC Server 4 (User-Mode) and finally select Run VNC
Server.
To stop VNC Server 4
1 Right click on the VNC Server icon in thesystem tray to display a popup menu. Selectthe Close VNC Serveroption.
The VNC Server 4 will remain dormant until an incoming connection request is received,whereupon it will deal w ith the request. In doing this, it will apply all relevant connection,security and operation options, as determined by the settings within the VNC Server Proper-
ties dialog.
Using VNC Server 4
In operation, VNC Server 4 remains almost unnoticed in the background, using minimalsystem resources. Its only visibility is as an icon within the system tray(or notification area) in
the lower right corner of the Windows screen.
Dormant VNC Server 4 icon within the system tray - this indicates
that the server is running but not currently actively connected
Move the mouse cursor over the VNC Server 4 icon to discover the servers
IP address as well as its current operation mode:Serviceor User
Active VNC Server 4 icon within the system tray - this indicates
that the server is running and has at least one active connection
Starting and stopping VNC Server 4If VNC Server 4 has not been configured to start automatically, then you can start it, in eitherits Useror Servicemodes, using the Start menu.
Note: SeeTwo modes of operation for more details about User and Service modes.
Starting and stopping in user-mode
To start VNC Server 4 (user-mode)
1 Click the Windows Startbutton and choose All Programs(or Programsinnon-XP versions).
A confirmation dialog will be displayed:
2 Click the Yesbutton to proceed.
Connecting to (and from) VNC Server 4Once running (in Service- or User- Modes) VNC Server 4 can be accessed either by VNCViewers or any Java-enabled web browser - see the VNC Viewer 4 user guidefor full details.
Additionally, the server system can be made to initiate connections to VNC Viewers that have
been set to listen for such approaches - see Listening viewer (server-initiated connection) fordetails.
8/8/2019 Set Up Winvnc
8/37
indexfurther informationusing vnc server 4introduction installation configuration8page
Starting and stopping in service-mode
To start VNC Server 4 (service-mode)
1 Click the Windows Startbutton and choose All Programs(or Programsin
non-XP versions).
2 Select the RealVNCentry, then VNC Server 4 (Serv ice-Mode)and finally select Start VNCService.
2 Select the RealVNCentry, then VNC Server 4 (Serv ice-Mode)and finally select StopVNC Server. A confirmation dialog will be displayed:
3 Click the Yesbutton to proceed
To stop VNC Server 4 (service-mode)
There are two ways to stop the VNC Server 4 when running in service-mode, either:
Use the VNC Server system tray icon (as per the user-mode instructions), or
Use the Start menu:
1 Click the Windows Startbutton and choose All Programs(or Programsinnon-XP versions).
8/8/2019 Set Up Winvnc
9/37
indexfurther informationusing vnc server 4introduction installation configuration9page
Further information
This section provides detailed information on a range of subjects related to VNC Server 4:
Options when installing An overview of the installation and explanation of the available options.
Using the tray iconA description of features available via the VNC tray icon.
VNC Server Properties Displaying VNC Server Properties
Security Connections Inputs Sharing Desktop Hooks Legacy
NT Logon authentication
Two modes of operationUser mode Service mode
Listening viewer (server-initiated connection)
Access control: Allow, deny or query addresses Calculating a range mask for access control
Ordering the access control list entries
Dealing with firewalls Changing VNC ports
What is an IP address?
What is a subnet mask?
How a subnet mask actually works
What is a port?
Windows versions and limitations
Troubleshooting
Support
8/8/2019 Set Up Winvnc
10/37
indexfurther informationusing vnc server 4introduction installation configuration10page
Options when installingFor the majority of VNC Server 4 installations, simply clicking through with the setupscreens using the Nextbutton will be sufficient. For situations where alternative settings maybe required, this section provides an overview of the setup procedure.
To install VNC Server 4
1 Run the downloaded self-extracting installer.
2 When the setup program begins, click the Nextbutton to acknowledge the welcomescreen:
3 License Agreement page: Read the License Agreement page, select the I accept the agree-
mentoption and click the Nextbutton.
4 Select Destination Location page: Click the Nextbutton to accept the default VNC folderlocation, or use the Browsebutton to select an alternative location.
5 Select components page: Both the VNC Serverand VNC Viewerwill be installed by de-fault. Untick options, as necessary, to prevent their installation. Click the Nextbutton tocontinue.
6 Select Start Menu Folder: Click the Nextbutton to agree RealVNCas the start menu foldername, or use the Browsebutton to locate an alternative. Optionally, tick Dont create a StartMenu folderto avoid adding any VNC entries to the Windows start menu.
7 Select Additional Tasks page: Set the required options and click the Nextbutton:
8 Ready to install page: This page provides a summary of all installation options. Click the
Installbutton to begin creating components within the selected folder.
9 VNC Server Properties page: IfRegisterand configure VNC Server for Service-Mode
was ticked, the VNC Server Propertiespagewill be displayed. You can either make anyrequired configuration changes now or ata later time. See the Configuration section
for details. Click OK.
10 IfRegister and configure VNC Server for Service-Modewas ticked and an existing securekey was not found then you will be
given the option of having one auto-matically generated.
Click OK. A confirmation message
will be given when the key has beengenerated.
continued
Tick to create a VNC Viewer icon
on your Windows desktop.
Tick to create a VNC Viewer icon
within the Quick Launch section
adjacent to the Start button.
Tick to perform the necessary
system registration to allow VNC
Server 4 to run as a Windows
service.
Tick to automatically run VNC
Server 4 as a Windows service at
every boot-up.
Tick to configure the necessary
license key. This step needs to
be completed either now or at a
later time before operation can
take place.
8/8/2019 Set Up Winvnc
11/37
indexfurther informationusing vnc server 4introduction installation configuration11page
11 IfVNC Authentication (the default) was
selected, and no VNC password is currentlystored, then you will be prompted to sup-ply one, to be used to authenticate incoming
viewer connections. Enter a new password,enter it again to confirm and click OK.
12 IfInstall a VNC Server licence keywas ticked, anda valid licence key is not currently installed, then
you will be prompted to supply a licence key. Thelicense key will have been emailed to you when youpurchased your VNC Enterprise Edition license.Either copy and paste the supplied license key and
click OKor, if you are evaluating VNC Server 4,click the Trial Licensebutton.
13 Information page: After installation has taken place, a list of acknowledgements and a re-
minder of the end user license agreement will be displayed. Please read through and thenclick the Nextbutton.
14 In the final page, click
the Finish button toconclude the installa-
tion procedure.
8/8/2019 Set Up Winvnc
12/37
indexfurther informationusing vnc server 4introduction installation configuration12page
Using the tray iconVNC server installs an icon in the system tray, located on the right-hand side of the task bar.This has several functions:
If you hover the mouse pointer over the tray icon, it will display the IP address of yourcomputer.
The background colour of the tray icon indicates whether or not there is anyone con-nected to your computer. A black background indicates at least one connection, whereas a
white background indicates no connections. Right-clicking on the tray icon will bring up a menu for
configuring and interacting with the program: Options... opens the options dialog. See VNC Server
Properties for details. If the VNC server is running inService-Mode, then this option will be unavailable un-less you have administrative privileges on the compu-
ter. Add New Clientallows you to make a reverse connec-
tion to a listening viewer. See Listening viewer (server-
initiated connection) for details. Disconnect Clientsdisconnects anyone currently connected to the VNC server. Connections... opens the connection management dialog. Guest Login enables or disables the guest login.
Close VNC Servercloses the VNC server. If the VNC server is running in Service-Mode,then this option will be unavailable unless you have administrative privileges on thecomputer.
About... shows program and version information. Double-clicking on the tray icon is equivalent to the Options... menu item if it is available,
or the About... menu item otherwise.
Connection managementYou can use this dialog to check who is connected to your computer and from where. Thecurrent connections are listed, allowing you to see at a glance the IP address and port numberof each. Click on a connection to see details of the username that was entered when the
connection was made and the current level of access. Click Change... to view or change accesspermissions. Click Disconnectto disconnect that user; other connected users are unaffected.
Enabling guest loginAt times it may be desirable for a user to temporarily allow access to their desktop on a
controlled basis. If VNC Server 4 has been configured to allow it, the user can enable a guestlogin to temporarily allow restricted access to the local desktop. Anyone logging in as guestmust be approved by the local user, even if the server is not otherwise configured to queryconnection attempts.
The guestlogin can be enabled or disabled by any user even if the VNC Server is running inService-Mode. This differs from other VNC Server Properties, which can only be modifiedby users with administrative privileges on the local computer when VNC Server is running in
Service-Mode. If the guestlogin is enabled when VNC Server is closed, it will not be enablednext time it starts up.
8/8/2019 Set Up Winvnc
13/37
indexfurther informationusing vnc server 4introduction installation configuration13page
VNC Server PropertiesThe VNC Server Properties dialog is where the key aspects of operation are configured viaseven tabbed pages which are labelled as follows:
Security
Connections
Inputs
Sharing
Desktop
Capture method (Hooks)
Legacy
During installation the settings contained within this dialog are configured to meet thegeneral requirements of most common installations. However, for assistance on customisingoperation for particular tasks, please see the Configuration section.
Displaying VNC Server PropertiesThe VNC Server Properties dialog can be accessed either from the VNC Server 4 system trayicon, or from the Windows Start button.
To display VNC Server Properties (via the system tray icon)
1 In the lower right hand corner of the Windows task bar, move the mouse pointer over the
VNC icon.
If no icon is visible then VNC Server 4 may not be running, see Starting VNC Server 4for details.
2 Click the right mouse button to reveal a popup menu.3 Use the left mouse button to select Options
The VNC Server Properties window will be displayedwith the Securitytab selected.
To display VNC Server Properties (via the Start menu)
1 Click the Windows Startbutton. Choose All Programs(or Programsin non-XP versions)and then select the RealVNCentry.
2 Choose the Start menu sub-options that are appropriate to the VNC Server mode that wi llbe used, either:
Select VNC Server 4 (Serv ice-Mode)and then choose Configure VNC Service, or Select VNC Server 4 (User-Mode) and then choose Configure User-Mode Settings.
In either case the appropriate VNC Server Properties window will be displayed with theSecuritytab selected.
8/8/2019 Set Up Winvnc
14/37
indexfurther informationusing vnc server 4introduction installation configuration14page
SecurityThe security tab is concerned with twoimportant operational areas: User authenti-cation and Encryption.
No Authentication
When selected, this option will allow viewerapplications to connect with the VNCServer without the need for username or
password. This option can be useful whenthe server system is operating within a com-pletely secure environment such as a LocalArea Network or Virtual Private Network,
to remove the requirement for authentica-tion.[Command line equivalent: UserPasswdVerifier=None]
IMPORTANT: Use this option with extreme caution. Do NOT use it unless the host network isknown to be completely secure.
Note: Encryption can be used even if No authentication is configured.
VNC Password Authentication
When selected, this option will require any viewer application to supply a valid password beforegranting access to the server system. Use the adjacent Configurebutton to create up to four pass-words, each of up to 255 characters. Note: If the Encryption option is not set to Always On thenlegacy viewers will be required to provide only the first eight characters of any password.
[Command line equivalent: UserPasswdVerifier=VncAuth]
Configure
Click this button to create a password of up to 255 characters that you will use to access theVNC Server. There are no imposed minimum requirements for the password, however, youare strongly recommended to use at least six characters and to use a mixture of letters andnumerals. When VNC Server is accessed by older VNC viewers, only the first 8 characters will
of the password will be checked. It is therefore advisable to set the Encryption levelto AlwaysOn, to prevent legacy viewers connecting, for maximum security.
VNC Extended Authentication
Starting with version 4.1.4, the standard VNC Password authentication has been supercededby VNC Extended Authentication. This allows up to four passwords each of up to 255 charac-
ters for a standard user, an admin user, a view-only user and an input-only user. To configurethe admin, view-only and input-only passwords, click the Extended Configuration button toaccess the VNC Extended Authentication dialog.
NT Logon Authentication
This option (not available on Windows 95, 98 or Me installations) links into the internal
security system within Windows NT, 2003 Server and XP. The advantage of this method isthat, using the Windows user configurations, you can grant different permissions for differenttypes of users, e.g. administrators, guests, users, etc.[Command line equivalent: UserPasswdVerifier=NtLogon]
Configure
Click this button to gain access to the Windows permissions for VNC Server dialog. Fromhere you can select existing user groups for the server system and edit their permissions.
Allow Single Sign-On authentication
If single sign-on is enabled in both the VNC server and the VNC viewer, then the viewer willinitially attempt to authenticate the user using his or her login credentials. Only if this fails
is the user prompted for a username and password. The advantage of single sign-on is thatthe user does not have to re-enter his or her password. However, in an environment whereworkstations are regularly left unattended and unlocked, it can introduce a security risk.
IMPORTANT: Under Windows NT 4, if single sign-on is enabled on the server, then only viewersrunning under Windows NT 4 will be able to connect using single sign-on. To connect from otherviewers you must explicitly disable single sign-on in either the server or the viewerthe viewer
will not automatically prompt the user for a username and password in this situation. This isdue to a limitation of Windows NT 4.
Note: The authentication and encryption
settings are very closely related and the overalleffect on security is a product of both settings.
8/8/2019 Set Up Winvnc
15/37
indexfurther informationusing vnc server 4introduction installation configuration15page
Encryption
[Command line equivalents: SecurityTypes=see {entries} below]
This option allows you to determine how encryption will be applied to user connections.There are three choices:
Prefer Off: Creates un-encrypted links unless an incoming VNC Viewer has its settings asPrefer On or Always On, in which case the link would be encrypted. {RA2ne,None,RA2}
Prefer On: Creates encrypted links unless an incoming VNC Viewer has i ts settings as PreferOff , in which case the link would be un-encrypted. {RA2,RA2ne,None}
Always On: Forces all viewer connections to be encrypted. Legacy viewers cannot connect
when this setting is used. {RA2}
In addition to the SecurityTypes parameter values given above, if single sign-on is enabled,then RA2 and RA2ne are replaced with SSPI,RA2 and SSPIne,RA2ne, respectively.
Generate Keys
Click this button to create new RSA keys that are used as the basis for link encryption. Thisoperation normally needs to be carried out once only during installation.
Guest login access
[Command line equivalent: GuestAccess=see below]
When set to None (guest login disabled), {GuestAccess=0} the local user cannot enable theguest login (see Enabling guest login). Otherwise, the user can temporarily allow access to the
desktop with either View-only {GuestAccess=v}or Interactive {GuestAccess=d}permissions.The guest login differs from standard user logins in that all connections must be explicitlyapproved by the local user, even if the query connect feature is not enabled. This can be over-ridden by editing the GuestAccess value in the registry. For example, setting {GuestAccess=f}
will give guest users all access rights, including bypassing the query connect dialog (notrecommended).
Prompt local user to accept connections
[Command line equivalent: QueryConnect=true/false]
When ticked, when a VNC viewer connects, a confirma-tion dialog is displayed on the server system indicating the
user name supplied by the viewer and the IP address fromwhich the connection originates. If no response is given(by the server user) within ten seconds, the connection is
rejected. If a second viewer attempts to make access duringthis time, then it will be immediately rejected.
When querying of connections is enabled, the server userhas the option of allowing the viewer user to connect with the permissions they would nor-mally have, refusing the connection completely, or allowing the connection to go ahead withviewer-only access to the desktop.
Only prompt when there is a user logged on
[Command line equivalent: QueryOnlyIfLoggedOn=true/false]
When ticked, if a local user is logged on to the server system, they will be prompted to acceptor reject incoming connections. With no local user logged on, connections are permitted asnormal, subject to the other connection criteria.
8/8/2019 Set Up Winvnc
16/37
indexfurther informationusing vnc server 4introduction installation configuration16page
ConnectionsThis tab determines key connection detailsrelating to the IP ports used, the IP addressesfrom which viewer connections will be ac-
cepted and also the idle disconnection time.
Serving Java separately
This is useful in situations where the number of open ports needs to be minimised forsecurity. You can configure a central VNC Server to serve the Java applet to browsers, which(once loaded) can then contact alternative VNC Servers. Thus, only one central port at 5800
is required, rather than one per server. The browsers used must have a Java Virtual Machine(JVM) that supports signed applets. Currently the Opera and Firefox browsers are known tobe capable, as is Internet Explorer with Suns JVM installed..
Access control
This area allows you to restrict access from incoming viewers according to their originat-
ing/source IP addresses. Addresses can be specifically accepted or rejected on any scale from asingle address right up to small or large scale subnets of addresses.
Only accept connections from the local machine
When ticked, this option will cause the access control settings (if any) to be ignored andmake the VNC Server 4 system inaccessible via all network interfaces except the local loop-back interface.
[Command line equivalent: LocalHost=true/false]
Access address area
The access address area is where specific addresses or ranges of addresses are declared and setto be Allowed(denoted by a + prefix), Denied(denoted by a prefix) or Queried(denoted bya ? prefix).
Each entry in the list comprises an action (+, -, ?), followed by an address pattern. Addresspatterns consist of an IP address or address prefix, followed by a subnet-style mask. The maskis used to determine how much of the IP address prefix must match the originating address
of an incoming connection for the rule to apply to that connection. As standard, the list isempty except for a single Allow All entry (+0.0.0.0/0.0.0.0), which matches all possible IPaddresses of connections and Allows them. If none of the specified rules apply to an incom-ing connection then the connection will be automatically rejected, for security.
Consider the following example entries:
Accept connections on port
This option indicates the port through whichviewer clients will be served. The standard
setting of 5900 is expected by VNC viewerapplications; however, if this port clasheswith another local network service, then itcan be changed to use any other vacant port
number. Please note, however, if you alter thisnumber, then the viewer user(s) will needto specify the non-standard port number as
part of the network address when logging-in.Please see VNC Viewer documentation - Making a connection for more details.[Command line equivalent: PortNumber=(port number)]
Disconnect idle clients after (seconds)
This option is similar to a screen-saver timeout, with the difference that when the specified
number of seconds has elapsed without any input from a particular viewer, the viewers con-nection will be closed. After the set period of time has elapsed since the last user interaction,VNC Server 4 will terminate the connection in order to conserve resources. As standard thisoption is set to 3600 seconds, or 1 hour. To prevent any connection timeouts, set this option
to 0 (zero).[Command line equivalent: IdleTimeout=(seconds)]
Serve Java viewer via HTTP on port
This option determines the port through which VNC Server 4 will provide the Java viewerapplet to Java-enabled browsers, when requested. As standard, the port number presented
here is 100 lower than the current main port address and will change accordingly wheneverthe main port is changed. If necessary, you can manually alter the Java viewer port number.You may wish, for example, to have the Java viewer served on the same port through which theserver accepts VNC connections in order to simplify firewall configuration (connections can
take up to 2 seconds longer when this is done). The Java Viewer can be disabled by untickingthe check box, if it is not required or if the Java Viewer is to be provided by a separate server.[Command line equivalent: HTTPPortNumber=(port number)]
The first entry includes access from a single specific address of
192.168.0.1
The second entry causes an access from the specific address
192.168.0.3 to be queried (the local user of the server system will need
to approve the connection within ten seconds, otherwise it is refused).
The third entry provides access from any machine situated in the192.168.4 subnet.
The fourth entry denies access from any other IP address.
Note the original +(include all) entry has been removed.
Please see Ordering entries in the access control list for details about editing Access Controlentries.To exclude a particular address or range of addresses, create a Deny rule and place itbeforeany Allow rules.
[Command line equivalent: Hosts=[[, [...]]]]
8/8/2019 Set Up Winvnc
17/37
indexfurther informationusing vnc server 4introduction installation configuration17page
Send clipboard updates to clients
When ticked, any text added to the clipboard of the server system will be made availableto the clipboard of any viewer user who i s logged-in at the time. Disabling this option can
be useful in preventing private server information from being leaked via the clipboard byuntrusted viewer users.[Command line equivalent: SendCutText=true/false]
Allow input events to affect the screen-saver
When ticked, this option allows the mouse and/or keyboard activity from the incoming
viewer system to interrupt the screen-saver (if present) on the server system. This is a systemoption, implemented within later Windows versions and is not available under earlier releases(such as Windows NT).[There is no equivalent command line option.]
Share files with clients
When ticked, the viewer user can put files from their system onto the clipboard of the server,and vice versa. These files can then be pasted into a directory on the server. Note that theVNC Viewer must support file transfer and have it enabled for this to work.
[Command line equivalent: ShareFiles=true/false]
Disable local inputs while server is in use
When ticked, this option ignores any input from the servers own locally connected keyboardand/or mouse while remote VNC sessions are active. Note that the desktop remains visible.[Command line equivalent: DisableLocalInputs=true/false]
InputsThis tab determines the level of control thatincoming viewer applications (clients) cangain over the server system.
Accept pointer events from clients
When ticked, the viewer user is permitted to control the server using their mouse. In com-bination with the Accept keyboard events from clients and Accept clipboard updates fromclients options, disabling this control is useful for making the server a view only system.
[Command line equivalent: AcceptPointerEvents=true/false]
Accept keyboard events from clients
When ticked, the viewer user is permitted to control the server using their keyboard. Incombination with the Accept pointer events from clients and Accept clipboard updates fromclients options, disabling this control is useful for making the server a view only system.
[Command line equivalent: AcceptKeyEvents=true/false]
Accept clipboard updates from clients
When ticked, the viewer user can copy text from their system to the clipboard of the server. Incombination with the Accept pointer events from clients and Accept keyboard events fromclients options, disabling this control is useful for making the server a view only system.
[Command line equivalent: AcceptCutText=true/false]
8/8/2019 Set Up Winvnc
18/37
indexfurther informationusing vnc server 4introduction installation configuration18page
SharingThe options within this tab determine exactlyhow VNC Server 4 should behave when twoor more viewers are connected to the server
system.
When viewers connect, they request eithershared or non-shared connections to the
server. Such requests come into effect whenanother user is also viewing the same server.
The settings within this tab determine ex-actly how the server should respond to suchrequests.
Use clients preferred sharing setting
When selected, VNC Server 4 will defer to the Shared connection setting of the secondincoming viewer. If the second viewer is set to share, then it will be permitted to make the
connection, if not it will either be rejected or w ill replace the existing viewer, depending uponthe setting of the Non-shared connections replace existing ones option..[Command line equivalent: AlwaysShared=false, NeverShared=false]
Non-shared connections replace existing ones
This option will determine the outcome when a connection is non-shared, either by viewer
choice or when the Never treat new connections as shared option is selected. In such cases, ifthis option is ticked, then the existing user is disconnected. If this option is unticked, then thenew user is rejected.[Command line equivalent: DisconnectClients=true/false]
Always treat new connections as shared
When selected, all incoming connections are treated as shared and so no existing users will bedisconnected nor will new users be turned away.
[Command line equivalent: AlwaysShared=true,NeverShared=false]
Never treat new connections as shared
When selected, all incoming connections will treated as non-shared. When a second incom-ing connection attempt is made, it will either be rejected or the existing user will be discon-nected, depending upon the setting of the Non-shared connections replace existing ones
option.[Command line equivalent: NeverShared=true, AlwaysShared=false]
8/8/2019 Set Up Winvnc
19/37
indexfurther informationusing vnc server 4introduction installation configuration19page
DesktopThis tab provides opportunities to fine tuneperformance by reducing unnecessary desk-top effects and also allows you to determine
how the server system should be left after ithas been accessed.
When last client disconnects
Do nothing
When selected, there will be no change to the operation of the server once there are no moreVNC viewers connected to it.[Command line equivalent: DisconnectAction=None]
Lock workstation
When selected, after the last VNC viewer has disconnected, the server system will be tempo-
rarily locked and returned to its log-in screen. This option can help to avoid un-authorisedaccess where the system is left unattended and other people are in i ts vicinity.[Command line equivalent: DisconnectAction=Lock]
Logoff user
When selected, after the last VNC viewer has disconnected, the current user session of the
server system will be ended and the system returned to its initial log-in screen. This optionis useful to ensure that the server system never remains logged-on after a VNC session. Thisoption can help to avoid un-authorised access where the system is left unattended and otherpeople are in its vicinity.
[Command line equivalent: DisconnectAction=Logoff]
While connected
Remove wallpaper
When ticked, the wallpaper image (if used) on the server system will be removed and re-placed with a plain background whenever a VNC viewer is connected. This option will alsoattempt to disable Windows Active Desktop, if it is use. This can help to reduce transmitteddata and hence improve overall performance.
[Command line equivalent: RemoveWallpaper=true/false]
Remove background pattern
When ticked, the background pattern (if used) on the server system will be removed andreplaced with a plain background whenever a VNC viewer is connected. This can help toreduce transmitted data and hence improve overall performance.
[Command line equivalent: RemovePattern=true/false]
Disable user interface effects
When ticked, any visual user interface effects, such as animated drop-down boxes, will bedisabled whenever a VNC viewer is connected. This can help to reduce transmitted data andhence improve overall performance.
[Command line equivalent: DisableEffects=true/false]
8/8/2019 Set Up Winvnc
20/37
indexfurther informationusing vnc server 4introduction installation configuration20page
Capture Method (Hooks)This tab concerns the various methods thatVNC Server 4 can employ to keep track ofchanges to the desktop so that they may be
transmitted to the current VNC viewer(s).
Poll for changes to the desktop
When selected, this option polls the Windows display system for changes to the entiredesktop. This method is slower than the Use VNC Hooks... and Use VNC Mirror... options.However, it can be useful in cases where the other two methods encounter timing/compat-
ibility problems or cannot track an application that interfaces directly with the graphics card,such as with some DirectX applications.[Command line equivalent: CaptureMethod=poll]
[Command line equivalent (prior to v4.1): UseHooks=false]
Use VNC hooks to track graphical updates
When selected, this option employs the standard VNC hooks technique to monitor changesto the local desktop. VNC hooks allow VNC Server 4 to monitor the messages sent to on-screen windows in order to ascertain when their content may have changed. This method is
very successful; however, it can miss certain types of update or conversely can also mistakenlyreport areas as having changed when in fact they have not. For these reasons, you are recom-mended to use this method in conjunction with Poll console windows for updates option.[Command line equivalent: CaptureMethod==hooks]
[Command line equivalent (prior to v4.1): UseHooks=true]
Poll console windows for updates
When ticked, this option will track the visible parts of console windows and poll those areas
for changes. This option is best used in close combination with the Use VNC hooks to trackgraphical changes option because the rate of polling can be reduced, which helps to increase
performance.[Command line equivalent: PollConsoleWindows=true/false]
Use VNC Mirror driver to track changes
When selected, this option takes advantage of a Windows facility that mirrors all primary dis-play graphical updates to a secondary driver, such as VNC. This produces a fast and accurate
update method, however, it operates at a low system level and could encounter problems onsome systems. This option is disabled unless you have the VNC Mirror Driver installed.[Command line equivalent: CaptureMethod=mirror]
Capture alpha-blended windows
When ticked, this option tracks newer semi-transparent windows, as well as standard win-dows, including certain menus and tool tips. This method places higher requirements on theserver and can induce cursor flicker.[Command line equivalent: UseCaptureBlt=true/false]
Note: This tab is titled Hooks within VNCversions prior to v4.1.
8/8/2019 Set Up Winvnc
21/37
indexfurther informationusing vnc server 4introduction installation configuration21page
LegacyThis tab contains options that are usefulwhen migrating from an older version ofVNC Server and where existing users are still
using older viewers.
Import VNC 3.3 Settings
When selected, this option will attempt to overwrite the current VNC Server 4 settings with
those of a previous WinVNC 3.3 installation that was installed on the same system. The exactsettings that will be imported depend upon the current VNC Server 4 operation mode thatyou are using:
User-Mode VNC Server 4: Will attempt to approximate your personal VNC 3.3 settings.
Service-Mode VNC Server 4: Will attempt to match the default settings from the local system.
VNC Server 4 will warn you when it cannot match existing settings or if they are no longerrelevant.
It is not possible to run both WinVNC 3.3 and VNC Server 4 simultaneously on the same
port. Therefore, once the settings have been imported, you must either:
Separately uninstall the WinVNC 3.3 service, or
Configure one of the VNC Servers to operate on a different port number Please refer toChanging VNC Ports for further details.
Only use protocol version 3.3
When ticked, the VNC Server 4 will restrict its operation to use only the version 3.3 protocol.This option is only provided to allow compatibility with some poorly-behaved third-party
viewer software, which reports incorrect protocol version numbers or assumes the presenceof non-standard features.
Warning: Use this option with caution as the advanced VNC Server security features such as
encryption and NT Logon authentication must be disabled completely in order to support olderviewers.[Command line equivalent: Protocol3.3=true/false]
8/8/2019 Set Up Winvnc
22/37
indexfurther informationusing vnc server 4introduction installation configuration22page
VNC Extended authenticationOlder versions of VNC support VNC Password authentication, which has a single passwordto control access to the desktop. Current versions still support this method of authentication,but it has been extended to provide four different virtual users, each with a distinct pass-
word. Access to the desktop can be granted in a more controlled way using the following usernames:
userhas default access, meaning that anyone connecting as usercan view and interact
with the desktop using the keyboard and the mouse and can access the remote clip-board. However, if the QueryConnect feature is enabled, the local user can refuse the
connection. If no username is specified when a connection is made, useris substitutedas the default.
admin has full access, meaning that anyone connecting as admin has all access rightsdescribed above, but the local user is not queried to approve the connection, even if the
QueryConnect feature is enabled.
viewonlyhas permission to view the desktop, but cannot interact with it. Mouse andkeyboard input is disabled, and access to the remote clipboard is denied. As with user,
the local user can refuse the connection if QueryConnect is enabled.
inputonlyhas permission to interact with the desktop, but cannot view it. Mouse andkeyboard input and access to the remote clipboard is enabled, but the VNC Viewer win-
dow will remain blank. As with userand viewonly, the local user can refuse the connec-tion if QueryConnect is enabled. The inputonlyuser is included mostly for complete-ness; in most situations it is not useful.
Each password can be up to 255 characters in length. There are no imposed minimumrequirements for the passwords, however, you are strongly recommended to use at least sixcharacters and to use a mixture of letters and numerals.
Legacy viewers
VNC Enterprise Edition provides support for legacy VNC viewers if VNC Extended authen-
tication is enabled. Legacy viewers do not allow a username to be entered, so they can onlyauthenticate as user. It is important to note that legacy viewers do not support passwordslonger than 8 characters. If the user password is longer than this, only the first 8 characters
will be checked. For maximum security, you can prevent legacy viewers from connecting bysetting the encryption level to Always On.
Enabling VNC Extended authentication
To enable VNC Extended authentication, set the authentication mechanism to VNC Pass-word Authentication and then click the Configurebutton. This allows you to set the user
password. To set the admin, viewonlyor inputonlypasswords, click the Extended Configurationbutton. Select the users you want to enable and click the corresponding Set Passwordbuttonto set the password.
8/8/2019 Set Up Winvnc
23/37
indexfurther informationusing vnc server 4introduction installation configuration23page
NT Logon authenticationVNC Server 4 offers the ability to authenticate users via the native security system of Win-dows (not 95, 98 or Me) and allows you to grant different access rights to particular users orgroups.
Two main steps need to be completed via the Security tab:
Select the NT Logon Authentication option, and
Click the Access Controlbutton to configure suitable user/group rights.
To configure NT Logon user/group permissions
1 Display the Security tab within theVNC Server properties dialog.
2 Click the Access Controlbutton to display the permissions dialog:
The available access rights for users or groups via incoming VNC Viewer connections are asfollows:
View display contentsAllow the remote user to see the contents of the VNC Server desktop.
Send pointer events / Send keyboard events
Allow the remote user to interact with applications running in the VNC Server desktop.
Send and receive clipboard contents
Allow the clipboard contents to be synchronised between the viewer and server. Send and receive files
Allow file transfer (via clipboard copy and paste) between the viewer and server.
Default accessAllow the default level of access (View display contents, Send pointer & keyboard events,Send and receive clipboard contents, Send and receive files). When new access rights whichare enabled by default become available, users and groups previously configured with
Default access will automatically have access to them.
Connect without accept/reject promptAllow the remote user to connect without a local user having manually accepted the
connection. This allows the QueryConnect feature to be bypassed by particular users orgroups, for emergency access to servers.
Full accessGrant all available access rights. When new access rights become available, users with Fullaccess will automatically have access to them, regardless of whether they are granted bydefault.
The default access rights granted to users and groups are as follows:
Full access Members of the local Administrators group.
Members of the local or domain VNC Admins group, if available.
Default access Members of the local or domain VNC Users group, if available.
View display contents Members of the local or domain VNC View-only group, if avail-able.
NT Logon Session Logging
In addition to the default logging of connection attempts by VNC Server, the NtLogonauthentication method independently logs successfully authenticated sessions. Sessions log
events are stored in the Application Event Log of the machine that authenticated the session.
If a VNC connection is made using local user account credentials then the session will belogged in the host computers event log.
If a VNC connection is made using domain-based credentials then the session will belogged with one of the domains controllers.
Existing user or group names are displayed within the dialog. New users or groups can beadded to the list using the Add... button. The procedure for adding new users/groups is a
standard Windows function and is beyond the scope of this user guide.
8/8/2019 Set Up Winvnc
24/37
indexfurther informationusing vnc server 4introduction installation configuration24page
Two modes of operationVNC Server 4 offers two levels of operation so that you can match it to suit your needs. Thetwo levels are: User modeand Service mode. When you install VNC Server 4, both modes willbe available and you can choose which one to use. The differences between the two modes are
as follows:
User mode Runs as a normal application, according to the current users rights on the system.
Is not available when the user logs out or when the system is locked.
VNC Server can be configured independently by each system user who wishes to run it.
The NT logon authentication method is not supported in User mode under operatingsystems older than Windows XP.
Best used when:
You are a single user who requires occasional help from a remote third party, need to
infrequently share work or need to control your system from elsewhere.
Service mode Is available as soon as the system has finished starting up, and continues to be available
even when you have logged out or the system is locked.
Configured with a single set of system-wide options that apply regardless of which user (ifany) is logged in at the time.
Best used when:
Multiple local users of a system need to regularly offer remote access to their machine.
The system needs to be accessed by a central administrator.
System sharing/control is required out of hours when local users are normally loggedoff.
8/8/2019 Set Up Winvnc
25/37
indexfurther informationusing vnc server 4introduction installation configuration25page
Listening viewer (server-initiated connection)In certain circumstances it can be preferable for the VNC server to initiate connections to one
or more viewers, rather than the other way round. For instance:
Firewalls can often cause problems for incoming connections to server systems. When theserver initiates the connection to a viewer, this problem is overcome. The firewall must,
however, allow outgoing connections through port 5500. Also, if the viewer system isbehind its own firewall, then that must allow incoming connections, also at port 5500.
Where VNC is used in a classroom or presentation environment, the tutor/presenter can
make his server initiate connections to each of the viewer systems. In this way greater
overall control is retained and this method obviates the need to provide server connectioninformation to each user.
To create a listening viewer connection
Two main stages need to occur:
1 Set the VNC Viewer on each users system to listen.
On each VNC Viewer system:
i Click the Windows Startbutton.
ii Choose All Programs(or Programsin non-XP versions). Select the RealVNCentry, then
VNC Viewer 4and finally select Run Listening VNC Viewer.
(Alternatively, if starting VNC Viewer from a command line, add the switch -listen)
2 Prompt the VNC Server 4 to add a new client and enter the viewers IP address.
On the VNC Server 4 system:
i Right click on the VNC icon in the system tray.
ii From the popup menu, click the Add New Clientoption.
iiiIn the resulting popup dialog, enter the IP address
of the viewer system and click OK.No username or password are required.
Providing the correct address is entered and there are
no firewall issues with the viewer system, the VNCViewer will display the servers screen exactly as if ithad initiated the connection in the usual manner.
To end a listening viewer connection
Listening viewer connections can be terminated by either party, either:
From the viewer: Close the viewer window.
From the server: Right click on the VNC Server 4 icon in the system tray and select the
Disconnect Clientsoption.
8/8/2019 Set Up Winvnc
26/37
indexfurther informationusing vnc server 4introduction installation configuration26page
Access control: Allow, deny or query addresses
5 Select the Allow, Denyor Queryoptions, as necessary.
Note: The order of entries within the access control list is critical to the correct operation ofVNC Server 4. SeeOrdering the access control list entriesfor details.
6 Click the OKbutton to add the selected address to the list within the Connections tab.
7 Click the Applybutton in the lower right corner of the VNC Server Properties window.
Note: The + entry in the Access Control list means accept all addresses. If you wish to allow
only those addresses that you specify, then you must remove the + from the list. You shouldalso add the entry -0.0.0.0/0.0.0.0 (usually at the end of the list) to ensure that no other ad-
dresses can gain access.
You can now:
Add another address
Use the Move Up and Move Down buttons to adjust the order
Delete an unwanted entryThe Host IP address pattern dialog will be displayed.
4 In the edit area, enter or edit the required IP address followed by a / and then the range
mask see Calculating a range mask for access control for details.
Note: If you do not enter a range mask after the IP address, VNC Server 4 will assume thatyou intend to define a single address and automatically insert the necessary 255.255.255.255
for you.
VNC Server 4 provides the opportunity to specifically control connection requests from par-ticular IP addresses, or ranges of addresses. For each specified IP address or range, you can:
Allow connection attempts from such addresses will be accepted (with the correct pass-
word, if set),
Deny connection attempts from such an address will be rejected immediately.
Query connection attempts will be announced to the local server user, who will need to
confirm acceptance (within ten seconds), otherwise the connection will be rejected.
Each entry requires an action (Allow, Deny, Query) and apattern. Patterns consist of an IPaddress or prefix, and a range mask (similar in form and function to a Subnet Mask) describ-ing which parts of the supplied IP address must match and these are entered via the Connec-tions tab within the VNC Server Properties dialog.
To add or edit IP address ranges
1 Display the VNC Server Properties dialog (see To display VNC Server Properties).
2 Select the Connections tab
3 Either add or edit an entry:
Add a new entry: Click the Addbutton.
Edit an existing entry: Highlight the entry in the Access Control listand click the Editbutton.
8/8/2019 Set Up Winvnc
27/37
indexfurther informationusing vnc server 4introduction installation configuration27page
Calculating a range mask for access controlA range mask is used to define the number of IP addresses that will be given special treat-ment (either to be: allowed, deniedor queried) when attempting to connect with the VNCServer 4. The range mask operates in a similar manner to a standard subnet mask because
it informs the system (in this case the VNC Server 4) which sections of an IP address aresignificant, and which are not.
To understand the range mask, you need to view it in binary form. Thus, a typical range mask
of255.255.255.224looks like this when converted to binary:
11111111.11111111.11111111.11100000
The ones indicate the parts of a corresponding IP address that will be examined, whereas thezeroes mark the parts of the IP address that form the range and will be ignored. Hence, themore zeroes there are (and accordingly, the fewer ones), the larger the address range that will
be encompassed.
Note: A range mask of 255.255.255.255 examines the whole of the IP address and so defines asingle location.
Consider the IP address 192.168.8.22combined with a range mask of255.255.255.252. Onceapplied, the result is as follows:
11000000.10101000.00001000.00010110 IP address(decimal equivalent: 192.168.8.22)
11111111.11111111.11111111.11111100 Range mask(decimal equivalent: 255.255.255.252)
11000000.10101000.00001000.000101xx Result(xx values will be ignored)
11000000.10101000.00001000.00010100 lowest address in the range: 192.168.8.20
11000000.10101000.00001000.00010111 highest address in the range: 192.168.8.23
Thus, due to the two zeroes on the right hand side of the range mask, the values of the equiv-alent bits in the IP address are ignored. This means that addresses running from 192.168.8.20
(where these two bits are both zero) through to 192.168.8.23 (where these two bits are bothone) will all be treated in the same manner. This is the range that VNC Server 4 would allow,deny or query, as instructed.
If the range mask (for the same IP address) was changed to 255.255.248.0, then the third octetwould also be affected, as follows:
11000000.10101000.00001000.00010110 IP address(decimal equivalent: 192.168.8.22)
11111111.11111111.11111000.00000000 Range mask(decimal equivalent: 255.255.248.0)11000000.10101000.00001xxx.xxxxxxxx Result(xx values will be ignored)
11000000.10101000.00001000.00000000 lowest address in the range: 192.168.8.0
11000000.10101000.00001111.11111111 highest address in the range: 192.168.15.255
The following is a list of all valid octet numbers that can be used within a range mask. Thesevalues can be used at any of the four positions in the mask. However, if there is a zero at any
position (in binary) of any octet, then everything to the right of that zero, must also be a zero.
Mask value Binary Addresses encompassed
255 11111111 1 address
254 11111110 2 addresses
252 11111100 4 addresses
248 11111000 8 addresses240 11110000 16 addresses
224 11100000 32 addresses
192 11000000 64 addresses
128 10000000 128 addresses
0 00000000 256 addresses
In reality, the range that needs to be defined may not align itself neatly with even binaryboundaries. In such cases it may be necessary to use two or more entries, each with smallerranges to accomplish the task accurately. For example, to allow the range 192.168.8.19to
192.168.8.37, you would need the following entries:
IP address/Range mask
+192.168.8.19/255.255.255.255 defines 1 address
+192.168.8.20/255.255.255.252 defines 4 addresses
+192.168.8.24/255.255.255.248 defines 8 addresses
+192.168.8.32/255.255.255.252 defines 4 addresses
+192.168.8.36/255.255.255.254 defines 2 addresses
General tips
There should be no zeroes to the left of a one while i t is technically possible to mix onesand zeroes in a mask, it produces erratic results and should be avoided.
The stated IP address for each range can be from anywhere within the range, i.e. the stated
IP address does not have to be the first one; it could be the last or be from the middle of
the range.
8/8/2019 Set Up Winvnc
28/37
indexfurther informationusing vnc server 4introduction installation configuration28page
Ordering entries in the access control listWhen there are multiple entries within the Access Control list, the order of those entriesbecomes important due to the manner in which VNC Server 4 checks the list:
As a new access request is received from a viewer, VNC Server 4 will compare the incomingIP address with the Access Control list. Starting at the top of the list, it proceeds down-wards until the IP address of the incoming system matches an entry.
When a match is found, the action for that entry (+ Allow, Denyor ? Query) is carriedout.
Checks for this IP address will then cease, regardless of other matches further down the
list.
Therefore, it is vital to order the list correctly, particularly where an address might be cov-ered twice, for instance:
-192.168.1.0/255.255.255.0 Deny subnet 192.168.1.*
+192.168.1.24/255.255.255.255 Allow host 192.168.1.24
In this instance, a request to connect from a VNC viewer at 192.168.1.24 would be de-nied, even though it is specifically allowed in the second line in the list. This is because itmatches the criteria of the first line where the whole of the 192.168.1.* subnet is denied.
Swapping the order of the two lines would solve this particular problem.
To adjust the order of access control list entries
1 Display the VNC Server Properties window (see Displaying VNC Server Properties)
2 Select the Connectionstab.
3 Click the required entry in the Access Controllist to highlight it.
4 As appropriate, click either the Move Up or Move Down buttons to adjust its positionwithin the list.
5 Click the Applybutton in the lower right corner of the VNC Server Properties window.
To delete an access control list entry1 Display the VNC Server Properties window (see Displaying VNC Server Properties)
2 Select the Connectionstab.
3 Click the required entry in the Access Controllist to highlight it.
4 Click the Removebutton.
5 Click the Applybutton in the lower right corner of the VNC Server Properties window.
8/8/2019 Set Up Winvnc
29/37
indexfurther informationusing vnc server 4introduction installation configuration29page
Dealing with firewallsA common cause of VNC operational failures are related to firewalls. One of the key func-tions of a network firewall is to block the use of most port numbers by incoming networktraffic in order to prevent access by unauthorised or malicious users. Therefore, unless an ex-
ception is made for the specific ports used by VNC, any attempt to connect to a VNC Serversituated behind a firewall will be denied. There are a number of options available to you inthese situations:
Adjust the firewall rules to allow incoming traffic via the ports required by VNC,i.e. Port5900 and port 5800.
IMPORTANT: Firewall rule changes should be carried out only by an experienced operator.Incorrect configuration could leave a network open to attack. The exact details for changingrules alter between differing firewall types and are beyond the scope of this guide.
Place the VNC Server system outside the firewall and use its security to al low only au-
thorised users.
IMPORTANT: When placing the VNC Server externally to a firewall, i.e. with open access to
an outer network, such as the Internet, it is vital that full s ecurity features are employed, bothwithin VNC Server 4 and also for the operating system upon which the server is running. SeetheConfiguration section more details.
Set VNC viewers to listen and initiate connections from the VNC Server 4.
This removes the need to make the server accessible from outside the firewall. SeeListening
viewerfor details. Use Windows Firewall (Windows XP Service-Pack 2 and newer)
Recent versions of Windows XP include a built-in firewall. From Service Pack 2 onwards, the
firewall can be easily configured to allow particular applications to open whichever ports theyrequire. By adding an Application Exception to the Windows Firewall for the VNC Server,both User- and Service- mode servers can be made accessible remotely without the need forport numbers to be specified explicitly. The VNC server is able to detect Windows Firewall and
configure it automatically when the VNC Server Properties dialog is dismissed.
Changing VNC ports The VNC port Default setting: 5900 This is the main port through which the VNC con-
nection is channelled. This port is set as standard to 5900, which is where the VNC Viewerapplications will expect to find it.
The Java Viewer port Default setting: 5800 This port is used to serve the Java viewerapplet to requesting Web browsers. This port number is automatically set to be 100lessthan the main VNC port. However, you can adjust it to use any vacant port number, oreven to use the same port as is used for VNC connections.
To change port numbers
1 Display the VNC Server Properties window (see To display VNC Server Properties).
2 Select the Connectionstab.
3 Edit the required port number:
Edit this value to determine the main port used for viewer
connections. Remember, if this is set to any value other
than 5900, incoming viewers will need to specify the new
number. See VNC Viewer documentation - Making a con-
nection for details.
When you change the Accept connections
on port: entry, the Serve Java viewer viaHTTP on port: option will adjust itself toretain the same spacing, as currently exists,
between it and the main port number. Forinstance, if the main port is changed from5900 to 5950, then the Java port will ac-cordingly change from 5800 to 5850.
Note: To reduce the number of ports that areopen within a firewall, it is possible to s et theAccept connections on por t: and Serve Java
viewer via HTTP on port: to use the same
port number. The disadvantage of doing thisis that it will add a slight delay when con-
necting to the VNC Server 4. The perfor-mance of VNC Server 4 will not otherwisebe affected.
4 Click the Apply button in the lower right corner of the VNC Server Properties window.
Edit this value to select the port used to send the Java
viewer to browsers. Ensure that the check-box is also
ticked.
8/8/2019 Set Up Winvnc
30/37
indexfurther informationusing vnc server 4introduction installation configuration30page
What is an IP address?An IP addressis a unique identity given to every device connected to a network of any size:from a two system link up at home, to every system on the Internet.
IP addresses are written as four decimal numbers separated by full stops, such as 192.168.0.4This is called dotted decimal notation and is used as a means of concealing the equivalent realaddress that is actually used by computers and networking equipment. The bare truth is thatevery IP address is really a pattern of 32 ones and zeroes.
At the inception of the Internet in the 1960s and 1970s, even by wi ldest estimates, no one everexpected they would need more than the seemingly inexhaustible 4.2 billion unique address
patterns that are afforded by 32 ones and zeroes. However, two factors conspired to prove thisto be wrong: Firstly, the amazing proliferation and expansion of the Internet; and secondly,the rather inefficient way in which those addresses were originally handed out to organisa-tions and companies. The result was that by the early 1990s, it was already apparent that at
the projected growth rates, the reserve of 4.2 billion addresses would soon all be gone.
In order to prolong the current stocks of numbers, the allocation of addresses was greatlytightened and the idea ofpublicandprivateaddresses was introduced. In the opening sen-
tence here, it was stated that an IP address is a unique identity - this no longer strictly true.
Of the 4.2 billion possible addresses, almost all of them are still used as uniquepublicad-dresses. However, in the revised plan, three groups of addresses were held aside for use as
privateaddresses:
10.0.0.0 to 10.255.255.255 172.16.0.0 to 172.31.255.255
192.168.0.0 to 192.168.255.255
To avoid confusion, these rangesare never used as public addresses.
Now, when xyz company needs to connect their many internal computers to the Internet,they might only be given a single public address, say80.42.0.252. They would then connect aGatewaysystem to the Internet and give i t that unique public address. Situated on the otherside of that gateway would be the companys local network and every system in that local net-
work would receive a private IP address. For small local networks, the most common privateaddress range is that which starts at 192.168.0.0.
Every computer in the local network (or subnet) will use their number that is unique to them
within the local network. However, the public identity for all of those local systems, as they
pass information out across the Internet, will always be that of the gateway: 80.42.0.252. Itis the job of the gateway to translate addresses between the local and wider networks. The
gateway must ensure that messages and data are sent through to the correct locations withoutthe private addresses ever leaking out. Assisting with this task are the subnet mask and portnumbers. In this way, there are now many systems using similar private IP addresses, how-ever, because those numbers only ever exist in local domains, there is never any confusion.
Of course, most people never see an IP address. To make network addresses even more mem-orable than the dotted decimal notations (which in turn are used to the hide the true binary
values), they are usually converted into named addresses. Such conversions are handled bythe Domain Name System and your browser uses it every time you visit a web site.
No two devices on the Internet are permitted to have the same identity, how-ever, IP addresses are running out. Hence, public and private addresses were
introduced to alleviate the problem.
The systems in the xyz company appear to have the same private addresses as
those in the abc limited local network. However, there is no ambiguity because
to the outside world, they use the public addresses of their gateways. Their
gateways handle all of the address translation and ensure that the private
addresses never leak out onto the wider Internet.
8/8/2019 Set Up Winvnc
31/37
indexfurther informationusing vnc server 4introduction installation configuration31page
What is a Subnet mask?The very short answer is: A subnet mask helps to determine whether another device is withinthe same part of the network or elsewhere.
For the longer answer you need to consider, in basic terms, a typical local network consistingof several, or several hundred, systems connected together. Messages and data flow aroundevery part of the local network and are then picked up by the systems to which they are ad-dressed. Because all this information needs to go around the whole local network, there are
great performance (and security) advantages to splitting local networks into smaller collec-tions of systems, which are called subnets. A key part of making different subnets cooperate
efficiently is the subnet maskthat is given to every device along with their unique IP address.A subnet mask is expressed in the same way as an IP address in that it has four decimal num-bers separated by dots. A common subnet mask is 255.255.255.0
When System A (IP address 192.168.2.122and subnet mask 255.255.255.0) wants to send
information to System B (IP address 192.168.2.235), it must first check whether they are bothin the same part of the network (in the same subnet). To do this System A first performs acomparison between its own IP address and its own subnet mask:
How a subnet mask actually worksIn the subnet mask explanation opposite, the example given is 255.255.255.0. This is a com-
monly used subnet mask and is useful as an example because it helps to simplify matters.However, in reality a subnet mask might look like this:
255.255.255.224
This only starts to make sense when you look at the subnet mask in its binary form:
11111111.11111111.11111111.11100000
The portions covered from left to right by ones mark the Network ID (the location of thewhole subnet), while the zeroes on the right show that just the last four bits of the devices IPaddress are used as the Host ID (the devices position within the subnet).
The calculation that the devices carry out is known as a bitwise AND. Basically, when youstack up the IP Address and the subnet mask (both in binary), wherever the equivalent posi-tions in both rows have a one, the end result is one. Where either of them have a zero, the
result is zero. If you take the previous Device A example, but now use the new subnet maskmentioned above, the results are as follows:
11000000.10101000.10000000.01100110 IP address(decimal equivalent: 192.168.128.102)
11111111.11111111.11111111.11100000 Subnet mask(decimal equivalent: 255.255.255.224
11000000.10101000.10000000.01100000 Result(decimal equivalent: 192.168.128.96)
Using this method you can see that only the last four bits are affected and this means thatany of the other IP addresses from the same subnet: 192.168.128.96 through to 192.168.2.127would produce the same result.
Using the new subnet mask on the Device B address from the previous example would pro-duce the following result:
11000000.10101000.10000000.11011011 IP address(decimal equivalent: 192.168.128.219)
11111111.11111111.11111111.11100000 Subnet mask(decimal equivalent: 255.255.255.224
11000000.10101000.10000000.11000000 Result(decimal equivalent: 192.168.128.192)
192.168.128.96 =192.168.128.192 ? Hence, the two devices now lie in different subnets and the information would need to travelvia a gateway/router.
The parts corresponding to 255s in the subnet mask
indicate the Network ID (which defines the identity of
the subnet).
The part corresponding to 0 in the mask shows the Host
ID (which defines a systems position within the subnet).
Only the Network ID parts are required when determin-
ing whether the two addresses belong to the same
subnet. Therefore, the Host ID portion is reduced to zero
because it is not needed for this calculation.
The sending system then repeats the subnet mask comparison, but this time w ith the destina-
tion address:
192.168.128.102 System A address
255.255.255.000 Subnet mask
192.168.128.000 Result
192.168.128.219 System B address
255.255.255.000 Subnet mask
192.168.128.000 Result
The results of the two subnet mask calculations can then themselves be compared:
192.168.128.0 = 192.168.128.0 ? If the two results are equal, then the two addresses lie within the same subnet.
If the two results are not equal, then the destination device is wi thin a different subnet, in
which case, the sender will mark the information to go via the gateway system onto a dif-ferent network or subnet.
8/8/2019 Set Up Winvnc
32/37
indexfurther informationusing vnc server 4introduction installation configuration32page
What is a port?Not to be confused with a physical port (such as a USB port or a printer port) to which youconnect devices, a Portin this context could be more accurately described as a service contactpoint. It provides an indication of where to locate an appropriate known service that can deal
with the kind of data being transmitted.
Imagine the problem that exists for networking equipment. A disparate mixture of messagesand information are continually flowing from system to system, via gateways and routers, and
each needs to find the correct destination. In this process, the IP address plays a critical rolein making sure that the right items arrive at the right places, however, the unsung hero is defi-
nitely the port number. While the IP address directs the postman to the correct building, itsthe port number that gets the package through the door of the correct apartment. Withoutthe port number, there would be piles of unclaimed packages filling the foyer.
Every application that sends or receives information across a network uses a port number.
In many cases they are fixed numbers that are always used by particular applications, andbecause they are not often changed, they are not normally mentioned. For instance, if yousend an email (via the most common method), then your message will be marked with portnumber 25. Whenever you browse the Web, the information will always be denoted with port
number 80and VNC applications almost always send and receive using port number 5900.The systems at the receiving end then know to route messages marked as port 25to the emailserver, port 80to the web server, port 5900to the VNC server and so on.
You should not normally need to change the VNC port number within VNC Server 4, how-
ever, if you do then all viewers must declare the new port number when addressing the serversystem. For instance, if the port number was changed to 5950, then to reach a server at IP
address 192.168.0.2, the VNC Viewer user would need to enter:
192.168.0.2::5950 (note the double colons)
Port numbers can range from 0 to 65,535 and are generally divided into three ranges:
0 to 1023 are well known ports
1024 to 49151 are registered ports
49152 to 65535 are dynamic and/or private ports
A list of valid port numbers and their uses is maintained by the Internet Assigned Numbers
Authority and can be viewed at http://www.iana.org/assignments/port-numbers.
8/8/2019 Set Up Winvnc
33/37
indexfurther informationusing vnc server 4introduction installation configuration33page
VNC authentication and encryption
VNC user and server authentication
Open network connections pose a number of security challenges and the VNC system hasnow been updated to provide robust solutions. In addition to the possibility of attackersattempting to gain server access, there is also the chance that false servers can be spoofedto mimic real ones and lure users into disclosing important information. To defend against
server attackers, VNC provides secure password protection. To defeat server spoofers, VNCServers are now required to prove their authenticity by providing a uni