Post on 01-Aug-2016
description
transcript
1
SKILLDENTAREFERENCE BOOK
CALL US ON
01494 448474
FOR PRICES
01494 448474 | sales@skillbond.com | www.skillbond.com
Biggest Bitemark Supporter 2015
2
Application / speed recommendation
Materials / Range of Application Indications of use Cut Speed – rpm
Model plasters / Stone • Wet plaster, bulk material reduction• Dry plaster, bulk material reduction• Working on stone dies
55/80 /8550/51 /80 /8510
Ø 060 -070 10.000Ø 045 -060 10.000Ø 007 -023 15.000 -20.000Ø 023 -060 8.000 -10.000
Precious alloysInlays, Onlays, Crowns, Bridges, combination and Telescope works
• For fine and detailed elaboration, to smoothen surfaces, contour occlusal areas and refine margins
• Active bonding structuring of metal surfaces prior to ceramic, resin or composite application
20/30 /31
40/41
Ø 007 -023 15.000 -30.000
Ø 007 -045 10.000 -12.000
Non Precious alloysCrown & Bridges, combination and telescope works
• For fine and detailed elaboration, to smoothen surfaces, contour occlusal areas and refine margins
• Active bonding structuring of metal surfaces prior to ceramic, resin or composite application
20/30 /31 /70
40/41
Ø 007 -023 15.000 -30.000
Ø 007 -045 10.000 -12.000
Cr Co alloys for partial dentures
• Rough trimming, contouring• Fine elaboration, smoothing of surfaces
1020
Ø 007 -023 15.000 -20.000Ø 023 -080 10.000 -15.000
Titanium / Crowns, Bridges • Trimming, contouring 24/25 /26 Ø 007 -023 15.000 -20.000Ø 023 -060 10.000 -15.000
Metal Ceramics / All CeramicsCrowns, Bridges, Inlays, Onlays, Laminates, Veneers, Facings
• For fine and detailed elaboration, to smoothen surfaces, contour occlusal areas, refine margins and ceramic / metal transition areas
30/31 Ø 007 -045 15.000 -20.000
C & B Acrylics Composite • For fine and detailed elaboration, to smoothen surfaces, contour occlusal areas, refine margins and veneers to metal transitions
30/31 Ø 014 -045 15.000 -20.000
Denture acrylicsand tray materials
• Removing flash
• Rough trimming
50/51 /5570/80 /8510/24 /70
20/70
Ø 023 -070 10.000 -15.000
Ø 007 -023 15.000 -20.000Ø 023 -080 10.000 -15.000Ø 012 -023 15.000 -20.000Ø 023 -060 10.000 -15.000Ø 023 -070 10.000 -15.000
Soft reline materials • Gingiva matrix contouring and fine finishing
• Trimming
75 Ø 023 -070 10.000 -15.000
Call us on 01494 448474 • email sales@skillbond.com • www.skillbond.com
3
plain cut superfine
x-cut superfine
Titanium-nitride coated LCC
x-cut fine
x-cut standard
plain cut standard
x-cut coarse
plain cut coarse
x-cut medium coarse
plain toothing with transverse
x-cut super coarse
plain cut super coarse
diamond cut prism
diamond cut medium
spiral cut fine
spiral cut superfine
special left hand cutters
Investment Trimmers
special ThF trimmers
contouring & fissure shaping
special MT instruments
Fissure finishers
yellow 30
60
31
20
10
70
50
80
51
75
55
85
40
41
24
25
90
24
yellow
red
blue
blue
green
green
black
green
black
black
blue
blue
velvet
velvet
red
velvet
cod
ing
colo
ur
cut
titanium toothing coarse
dry
cera
mic
s
pre
ciou
s al
loys
sem
i-pre
ciou
s al
loys
non-
pre
ciou
s al
loys
tita
nium
com
pos
ites
crow
ns &
bri
dge
s
CrC
o
CrN
i
mod
el c
ast
app
lianc
es
resi
ns
pla
ster
soft
rel
inin
gs
mill
ing
tec
hnic
ther
mof
orm
ing
cont
ouri
ng &
fis
sure
s 26black
Please Note: Using cutters marked with the indentation codes 40 - 85 the grinding movements must be done under constant pressure operating the instrument at the recommended speed.Danger of Injury – soft, timid or hesitant use of large intented instruments causes rock or toss vibration with the possibility of a shaft breakage.
Non-adherence to the maximum permissible speeds increases the risk of accidents.Recommended Speeds
ISO 1/10 mm rpm010 – 023 5.000 – 40.000025 – 045 15.000 – 30.000050 – 080 15.000 – 20.000
Laboratory Cutters
Application recommendations
4
L mm 14,0 16,0 16,0 16,0 17,0 8,0 8,0 4,0 5,5 7,0 5,5 8,0 4,0
1/10 mm 023 023 023 023 023 023 023 016 023 023 023 016 008
Order No. SET284 SET285 SET286 SET287 SET288 SET289 SET290 SET291 SET292 SET293 SET294 SET295 SET296
L mm 4,0 4,0 3,5 3,0 8,0 4,0 3,5 12,0 12,0 12,0 14,0 15,0 13,0
1/10 mm 009 010 014 014 023 023 012 060 060 060 060 060 045
Order No. SET297 SET298 SET299 SET300 SET301 SET302 SET303 SET304 SET305 SET306 SET307 SET308 SET309
L mm 14,0 13,0 14,0 9,0 8,0 9,5 11,5 12,5 11,0 0,8 1,0 1,2 1,4
1/10 mm 040 060 060 040 040 060 031 060 060 010 012 014 016
Order No. SET310 SET311 SET312 SET313 SET314 SET315 SET316 SET317 SET318 SET319 SET320 SET321 SET322
L mm 1,6 2,0 2,3 2,4 2,7 2,8 3,25 3,5 4,5 5,5 7,0 11,5 14,0
1/10 mm 018 023 025 027 029 031 035 040 050 060 080 040 060
Order No. SET323 SET324 SET325 SET326 SET327 SET328 SET329 SET330 SET331 SET332 SET333 SET334 SET335
L mm 5,0 5,0
1/10 mm 023 029
Order No. SET336 SET337L mm 3,5
1/10 mm 060
Order No. SET415
Repair Cutter
Tungsten Carbide Cutters • TC Cutter • Cut 10 • Cross Cut Standard • For coarse abrasion on chrome-colbalt alloys, precious metal alloys, nickel-chrome alloys, casting alloys and acrylics. 1
CALL US ON
01494 448474
FOR PRICES
5
L mm 14,0 16,0 16,0 8,0 8,0 16,0 17,0 8,0 8,0 5,5 8,0 3,5 3,0
1/10 mm 023 023 023 010 012 023 023 023 023 023 016 014 014
Order No. SET338 SET339 SET340 SET341 SET342 SET343 SET344 SET345 SET346 SET347 SET348 SET349 SET350
L mm 8,0 4,0 3,5 12,0 12,0 12,0 14,0 16,0 13,0 14,0 13,0 9,0 8,0
1/10 mm 023 023 012 060 060 060 060 060 045 040 060 040 040
Order No. SET351 SET352 SET353 SET354 SET355 SET356 SET357 SET358 SET359 SET360 SET361 SET362 SET363
L mm 9,5 11,5 11,0 2,0 14,0 3,0 5,0 5,0
1/10 mm 060 031 060 023 060 014 023 029
Order No. SET364 SET365 SET366 SET367 SET368 SET369 SET370 SET371
L mm 14,0 5,5 10,5 10,5 9,0 9,5 14,0 13,5 11,5 5,0 4,0 4,0 4,0
1/10 mm 023 023 023 023 023 023 060 040 040 023 008 009 010
Order No. SET1165 SET737 SET1166 SET1167 SET1168 SET1169 SET1170 SET1171 SET1172 SET1173 SET1174 SET1175 SET742
L mm 8,0 8,0 8,0 4,0 3,5 8,0 13,5 14,0
1/10 mm 023 023 016 008 014 023 040 060
Order No. SET202 SET203 SET204 SET205 SET206 SET207 SET208 SET209
Tungsten Carbide Cutters • TC Cutter • Cut 20 • Cross Cut Fine • Suitable for all dental materials. Smooths the surface and enables accurate operation on any structure.
Tungsten Carbide Cutters • TC Cutter • Cut 24 • Spiral Cut Fine • Ensures an exceptionally fine cutting surface on all alloys - especially titanium, as the special cut pattern avoids clogging.
Tungsten Carbide Cutters • TC Cutter • Cut 25 • Spiral Cut Superfine • Excellent cutting performance and chip removal on tough materials like titanium, non precious alloys, precious alloys, plaster, models, veneer resins and prosthetic repairs.
1
1
1
6
L mm 8,0 8,0 8,0 8,0 13,5
1/10 mm 023 023 016 023 040
Order No. SET210 SET211 SET212 SET213 SET214
L mm 14,0 16,0 16,0 17,0 8,0 8,0 5,5 7,0 5,5 8,0 3,5 3,5 8,0
1/10 mm 023 023 023 023 023 023 023 023 023 016 014 016 023
Order No. SET215 SET216 SET217 SET218 SET219 SET220 SET221 SET222 SET223 SET224 SET225 SET226 SET227
L mm 4,0 13,0 14,0 14,0 11,5 3,0 5,0 5,0
1/10 mm 023 045 040 045 040 014 023 029
Order No. SET228 SET229 SET230 SET231 SET232 SET233 SET234 SET235
L mm 14,0 16,0 16,0 5,5 7,0 5,5
1/10 mm 023 023 023 023 023 023
Order No. SET236 SET237 SET238 SET239 SET240 SET241
L mm 14,0 16,0 16,0 8,0 14,0
1/10 mm 023 023 023 023 045
Order No. SET242 SET243 SET244 SET246 SET248
Tungsten Carbide Cutters • TC Cutter • Cut 26 • Titanium Toothing Coarse • Suitable for titanium and titanium alloys.
Tungsten Carbide Cutters • TC Cutter • Cut 30 • Cross Cut Superfine • For fine finishing of gold, alloys and all versions of resins & composites - due to the special cut also ideally suited for ceramics avoiding occurrence of cracks.
Tungsten Carbide Cutters • TC Cutter • Cut 31 • Superfine Titanium-Nitride Coated • These special titanium-nitride coated cutters offer specific cool-cutting properties eg. for clasp preparation in the shoulder area, shortening of attachments, fine finishing of inlays including ceramic inlays.
Tungsten Carbide Cutters • TC Cutter • Cut 40 • Diamond Cut With Prism Surface • Causes a rough and streaky surface and thus an increased surface retention on the metal framework for ceramic or resin veneers.
1
1
1
7
Tungsten Carbide Cutters • TC Cutter • Cut 51 • Cross Cut Medium Coarse • For bulk reduction on dry plaster.
L mm 16,0 8,0 14,0
1/10 mm 023 023 045
Order No. SET251 SET255 SET256
L mm 12,0 12,0 12,0 14,0 15,0 13,0 13,0 14,0 11,0
1/10 mm 060 060 060 060 060 045 060 070 060
Order No. SET257 SET258 SET259 SET260 SET261 SET262 SET263 SET264 SET265
L mm 12,0 14,0
1/10 mm 060 060
Order No. SET266 SET267
L mm 14,0 13,0 14,0
1/10 mm 060 060 070
Order No. SET268 SET269 SET270
L mm 14,0 16,0 16,0 4,0 4,0 4,0 3,5 14,0
1/10 mm 023 023 023 008 009 010 016 045
Order No. SET271 SET272 SET276 SET277 SET278 SET279 SET281 SET282
L mm 4,0 4,0 4,0 12,0 12,0 12,0 14,0 15,0 13,0 14,0 13,0 14,0 9,5
1/10 mm 008 009 010 060 060 060 060 060 045 040 060 060 060
Order No. SET372 SET373 SET374 SET375 SET376 SET377 SET378 SET379 SET380 SET381 SET382 SET383 SET384
Tungsten Carbide Cutters • TC Cutter • Cut 41 • Diamond Cut For Slightly Rough Surface • Fine, scale-like cutting pattern for aesthetically most demanding veneers
Tungsten Carbide Cutters • TC Cutter • Cut 55 • Cross Cut Super Coarse • For gross reduction oresins and plaster as well as resin-based tray materials.
Tungsten Carbide Cutters • TC Cutter • Cut 60 • Plain Cut Superfine • Smooth cutting pattern on all alloys and composites, reduces re-work - especially suitable on prosthetic appliances for papilla shaping.
Tungsten Carbide Cutters • TC Cutter • Cut 70 • Plain Cut Standard • For all dental materials - the plain cut enables a smooth cutting patter, particularly on resins, and thus reduces re-work.
Tungsten Carbide Cutters • TC Cutter • Cut 50 • Cross Cut Coarse • For efficient reduction of resins including tray materials, as well as plaster.
1
1
1
1
1
1
CALL US ON
01494 448474
FOR PRICES
8
L mm 11,5 12,5 11,0 2,4 2,8 3,4 4,3 5,3 7,0 11,5 14,0
1/10 mm 031 060 060 027 031 040 050 060 080 040 060
Order No. SET385 SET386 SET387 SET388 SET389 SET390 SET391 SET392 SET393 SET394 SET395
L mm 14,0 12,0 14,0 14,0 14,0 9,0
1/10 mm 023 060 045 070 060 040
Order No. SET396 SET397 SET398 SET399 SET400 SET401
L mm 12,0 12,0 12,0 14,0 15,0 13,0 13,0 11,0
1/10 mm 060 060 060 060 060 045 060 060
Order No. SET402 SET403 SET404 SET405 SET406 SET407 SET408 SET409
L mm 14,0 13,0 14,0
1/10 mm 060 060 070
Order No. SET410 SET411 SET412
L mm 14,0
1/10 mm 060
Order No. SET414
Tungsten Carbide Cutters • TC Cutter • Cut 70 • Plain Cut Standard • For all dental materials - the plain cut enables a smooth cutting pattern, particularly on resins, and thus reduces re-work.
Tungsten Carbide Cutters • TC Cutter • Cut 75 • Plain Toothing With Transverse Section • For trimming of soft acrylics / soft relinings.
Tungsten Carbide Cutters • TC Cutter • Cut 80 • Plain Cut Coarse • Rapid and effective trimming of acrylic and plaster.
Tungsten Carbide Cutters • TC Cutter • Cut 85 • Plain Cut Super Coarse • For bulk abrasion on plaster and acrylics.
TC Cutter • Cut 90 • For safe and easy devesting of cast alloys. Its special blade geometry ensures investment is easily removed.
1
1
1
1
1
fine fine standard standard standard Plaster/Acrylic
L mm 16,0 13,0 14,0 13,0 14,0 14,0
1/10 mm 023 045 023 045 060 070
Order No. SET421 SET424 SET420 SET423 SET422 SET425
L mm 9,0 9,0 15,0 9,0
1/10 mm 014 023 023 023
Order No. SET418 SET419 SET416 SET417
3 3 1 1
Fissure burs are ideal for removing excess material on thermo-plastic materials - prevents smearing with soft materials.
Special cutters for left-hand use in 3 types of cut.1
9
L mm 14,0 16,0 16,0 17,0 5,5 8,0 4,0 3,0 13,0 14,0
1/10 mm 023 023 023 023 023 016 010 014 045 040
Order No. SET172 SET173 SET174 SET175 SET176 SET177 SET178 SET179 SET184 SET185
L mm 15,0 12,0 12,0 14,0 14,0
1/10 mm 060 060 060 060 060
Order No. SET183 SET180 SET181 SET182 SET186
L mm 14,0 16,0 16,0 8,0 3,0 13,0 14,0 14,0 14,0
1/10 mm 023 023 023 016 014 045 040 060 060
Order No. SET187 SET188 SET189 SET190 SET191 SET193 SET194 SET192 SET195
L mm 4,0 14,0 13,5
1/10 mm 010 060 040
Order No. SET196 SET198 SET197
L mm 14,0 13,0
1/10 mm 060 045
Order No. SET199 SET200
● Due to the DLC annealing process a special material (DLC) is diffused to a penetration depth of 90 μ into the tungsten carbide structure of the VOLCANO TC Cutters micro-smooth surface of the TC structure
● Especially sharp Cutter edges ensure an exceptionally high level of cutting efficiency – in addition to superior longevity – it simply lasts longer too
● The ultra-smooth surface in turn reduces operating friction facilitates removal of shavings, extremely silent and vibration-free cutter handling precise usage and maximum hardness HV
VOLCANO • Tungsten Carbide Cutters • TC Cutter • Cut 10 • Cross Cut Standard • For coarse abrasion on chrome-cobalt alloys, precious metal alloys, nickel-chrome alloys and acrylics.
VOLCANO • Tungsten Carbide Cutters • TC Cutter • Cut 20 • Cross Cut Fine • Suitable for all dental materials. It smooths the surface and enables accurate operation on any structure.
Advantages of VOLCANO Cutters
VOLCANO • Tungsten Carbide Cutters • TC Cutter • Cut 24 • Spiral Cut Fine • Ensures an exceptionally fine cutting surface on all alloys, especially titanium as the special cut pattern avoids clogging.
VOLCANO • Tungsten Carbide Cutters • TC Cutter • Cut 50 • Cross Cut Coarse • For efficient reduction of resins including tray materials as well as plaster.
1
1
1 1
10
Size 1/10 mm 005 006 007 008 009 010 012 014 016 018 021 023 027
Order No. SET004 SET005 SET006 SET007 SET008 SET009 SET010 SET011 SET012 SET013 SET014 SET015 SET017
Shank: 104 HP
C1Round↻max. 5.000 - 50.000
L mm 0,8 1 1,2 1,4 1,6 1,7
Size 1/10 mm 008 010 012 014 016 018
Order No. SET018 SET020 SET021 SET022 SET023 SET024Shank: 104 HP
C2Inverted Cone
↻max. 5.000 - 50.000
L mm 1,2 1,6
Size 1/10 mm 006 008
Order No. SET067 SET068Shank: 104 HP
L mm 4,4
Size 1/10 mm 014
Order No. SET070Shank: 104 HP
C7Pear
↻max. 5.000 - 50.000
C1Contouring Fissure Bur↻max. 30.000 - 40.000 Ceramics 15.000 - 25.000 Metal
6
6
6
6
C1For accurate preparation of fissures.
TC Burs & Finishers
C7LPear long
↻max. 5.000 - 50.000
6
Size 1/10 mm 002 003 004
Order No. SET001 SET002 SET003Shank: 104 HP
Call us today 01494 448474
11
TC Burs & Finishers
L mm 3,4 4,2 4,2 4,2 4,4 4,4
Size 1/10 mm 008 009 010 012 014 016
Order No. SET025 SET026 SET027 SET028 SET029 SET030Shank: 104 HP
L mm 3,4 4,2 4,2 4,2 4,4 4,4 4,8
Size 1/10 mm 008 009 010 012 014 016 018
Order No. SET035 SET036 SET037 SET038 SET039 SET040 SET041Shank: 104 HP
L mm 4,2 4,4
Size 1/10 mm 010 014
Order No. SET033 SET034Shank: 104 HP
L mm 6,0 6,0
Size 1/10 mm 010 012
Order No. SET031 SET032Shank: 104 HP
L mm 6,0
Size 1/10 mm 012
Order No. SET042Shank: 104 HP
C21Cylinder
↻max. 5.000 - 50.000
C21RCylinder round
↻max. 5.000 - 50.000
C21LCylinder long
↻max. 5.000 - 50.000
C23Tapered Fissure
↻max. 5.000 - 50.000
6
6
6
6
C23LLong Tapered Fissure
↻max. 5.000 - 50.000
6
SKILLDENTA PRICES EXCLUDE VAT & CARRIAGE, VALID FROM 31/05/2016. SUBJECT TO AVAILABILITY - E & OE. IMAGES ARE NOT TO SCALE
CALL US ON
01494 448474
FOR PRICES
12
C23RRound End Tapered Fissure
↻max. 5.000 - 50.000
C31Cylinder
↻max. 5.000 - 50.000
C31LCylinder long
↻max. 5.000 - 50.000
C31RCylinder round
↻max. 5.000 - 50.000
C33Tapered Fissure
↻max. 5.000 - 50.000
C33LTapered Fissure long
↻max. 5.000 - 50.000
6
6
6
6
6
6
L mm 4,2 4,2
Size 1/10 mm 010 012
Order No. SET043 SET044Shank: 104 HP
L mm 3,4 4,2 4,2 4,2 4,4 4,4
Size 1/10 mm 008 009 010 012 014 016
Order No. SET046 SET047 SET048 SET049 SET050 SET051Shank: 104 HP
L mm 6,0 6,0
Size 1/10 mm 010 012
Order No. SET052 SET053Shank: 104 HP
L mm 4,2 4,2 4,4
Size 1/10 mm 010 012 014
Order No. SET054 SET055 SET056Shank: 104 HP
L mm 4,2 4,2 4,2 4,2 4,6 4,6 4,8 4,8 5,3
Size 1/10 mm 008 009 010 012 014 016 018 021 023
Order No. SET057 SET058 SET059 SET060 SET061 SET062 SET063 SET064 SET065Shank: 104 HP
L mm 6,0
Size 1/10 mm 012
Order No. SET066Shank: 104 HP
TC Burs & Finishers
13
TC30Inverted Cone
↻max. HP 50.000
TC30XInverted Cone
↻max. 50.000
TC42Inverted Cone
↻max. 50.000
6
6
6
TC46Flame• 12 Blades
↻max. 300.000
TC246Flame• 12 Blades
↻max. 300.000
6 6
TC42XInverted Cone
↻max. 50.000
6
L mm 0,7 0,8 0,9 1,0 1,2 1,4
Size 1/10 mm 006 008 009 010 012 014
Order No. SET076 SET077 SET078 SET079 SET080 SET081Shank: 104 HP PRICE £27.29 £27.29 £27.29 £27.29 £27.29 £27.29
L mm 0,8 0,9 1,0 1,2 1,4
Size 1/10 mm 008 009 010 012 014
Order No. SET071 SET072 SET073 SET074 SET075Shank: 104 HP
L mm 1,7 3,1
Size 1/10 mm 018 023
Order No. SET084 SET023Shank: 104 HP
L mm 3,5
Size 1/10 mm 012
Order No. SET1155Shank: 104 HP
L mm 3,6 3,6 3,7
Size 1/10 mm 009 010 012
Order No. SET1156 SET1157 SET1158Shank: 104 HP
L mm 1,7 3,1
Size 1/10 mm 018 023
Order No. SET082 SET083Shank: 104 HP
TC Burs & Finishers
SKILLDENTA PRICES EXCLUDE VAT & CARRIAGE, VALID FROM 31/05/2016. SUBJECT TO AVAILABILITY - E & OE. IMAGES ARE NOT TO SCALE
CALL US ON
01494 448474
FOR PRICES
14
RF90Stippling Instrument
↻max. 5.000
Stippling Instruments creating natural looking gingiva matrix surfaces.
SET 743Fine stippling of gingiva matrix in the papilla areas.
6
TC850.3
Ceramic Finishing Bur / 3 - sided
↻max. 150.000 - 200.000 TC850.4
Ceramic Finishing Bur / 4 - sided
↻max. 150.000 - 200.000
TC850.6
Ceramic Finishing Bur / 6 - sided
↻max. FG 150.000 - 200.000, HP 50.000
Ceramic Finishing Bur
6
6
6
SET724 For anatomical shaping and trimming of occlusal contacts.
SET1160 Larger stippling of gingiva matrix in the alveole areas.
Operating Information
• Use only technically perfect, serviced handpieces.• Clean the handpiece chuck regularly.• Instruments must be inserted as far as possible.• Use eye-shield and dust-extraction.• Instruments should reach the operating speed before they are applied to the work piece.• Avoid canting or levering the instrument as this increases the risk of breakage.• Incorrect application leads to inferior results and increases the risk.
Worn Instruments
Fractured and incorrectly shaped blades cause vibrations.
Bent or non-concentric rotary instruments must be disposed of.
Working Pressure
Excessive working pressure must be avoided.Pressure: 0.2 – 0.5 N
In extreme cases, the instrument may even fracture.
Non-adherence to the maximum permissible speeds increases the risk of accidents.See pages 8 / 9.
Recommended Speeds
ISO 1/10 mm rpm010 – 023 5.000 – 40.000025 – 045 15.000 – 30.000050 – 080 15.000 – 20.000
Laboratory Cutters
Type of cuts upmCross cut 5.000 – 10.000Plain cut 3.000 – 5.000Chamfer ground section 6.000Wax cutter 3.000
Milling Technique
Size 1/10 mm 012 014 016
Order No. SET743 SET1159 SET1160Shank: 104 HP
L mm 2,5
Working part: 9° Size 1/10 mm 014
Order No. SET724Shank: 104 HP
L mm 2,5
Working part: 10° Size 1/10 mm 012
Order No. SET1161Shank: 104 HP
L mm 2,5
Working part: 12° Size 1/10 mm 010
Order No. SET1162Shank: 314 FG
Order No. SET086Shank: 104 HP
15
In bevels and adjacent surfaces.For fissures, minor corrections on inside surfaces.Open or deepen the dissectional fissures.
74
Stahlbohrer • Steel burS • InStrumentS en acIer
Steel instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated cutting blade geo-metry and cutter designs ensure a long ser-vice life and high cutting capacity when prepa-ring stone, acrylic, metal and precious metal.
Instruments specifically tailored to the relevant material and technique.
Öffnen oder Vertiefen der HauptfissurenOpen or deepen the dissectional fissuresOuverture et approfondissement des sillons principaux
Für Fissuren, kleine Korrekturen an Innenflä-chenFor fissures, minor corrections on inside sur-facesPour sillions, menues corrections des intrados
In Hohlkehlen und angrenzenden FlächenIn bevels and adjacent surfacesDans les congés creux et sur les surfaces avoisinantes
Instruments en acier pour des travaux de précision
Pour un retrait optimal du matériau et une qua-lité de surface fine.
Grande longévité et capacité de coupe éle-vée pour le traitement du plâtre, de la résine, du métal, et du métal précieux grâce à une denture adaptée optimale et aux formes des fraises.
Instruments spécialement adaptés pour les matériaux et travaux correspondants.
Stahlinstrumente für präzise arbeitsergebnisse
Für optimalen Materialabtrag und feine Ober-flächengüte.
Hohe Standzeiten und Schneidleistungen beim Bearbeiten von Gips, Kunststoff, Metall und Edelmetall durch die optimal abgestimm-ten Verzahnungen und Fräserformen.
Instrumente speziell auf die jeweiligen Werk-stoffe und Arbeiten abgestimmt.
Abrunden scharfer Kanten und Glätten okklu-saler KonturenTake off sharp edges and smoothen occlusal surfacesAdoucissement de bords tranchants et lissage des contours occlusaux
74
Stahlbohrer • Steel burS • InStrumentS en acIer
Steel instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated cutting blade geo-metry and cutter designs ensure a long ser-vice life and high cutting capacity when prepa-ring stone, acrylic, metal and precious metal.
Instruments specifically tailored to the relevant material and technique.
Öffnen oder Vertiefen der HauptfissurenOpen or deepen the dissectional fissuresOuverture et approfondissement des sillons principaux
Für Fissuren, kleine Korrekturen an Innenflä-chenFor fissures, minor corrections on inside sur-facesPour sillions, menues corrections des intrados
In Hohlkehlen und angrenzenden FlächenIn bevels and adjacent surfacesDans les congés creux et sur les surfaces avoisinantes
Instruments en acier pour des travaux de précision
Pour un retrait optimal du matériau et une qua-lité de surface fine.
Grande longévité et capacité de coupe éle-vée pour le traitement du plâtre, de la résine, du métal, et du métal précieux grâce à une denture adaptée optimale et aux formes des fraises.
Instruments spécialement adaptés pour les matériaux et travaux correspondants.
Stahlinstrumente für präzise arbeitsergebnisse
Für optimalen Materialabtrag und feine Ober-flächengüte.
Hohe Standzeiten und Schneidleistungen beim Bearbeiten von Gips, Kunststoff, Metall und Edelmetall durch die optimal abgestimm-ten Verzahnungen und Fräserformen.
Instrumente speziell auf die jeweiligen Werk-stoffe und Arbeiten abgestimmt.
Abrunden scharfer Kanten und Glätten okklu-saler KonturenTake off sharp edges and smoothen occlusal surfacesAdoucissement de bords tranchants et lissage des contours occlusaux
74
Stahlbohrer • Steel burS • InStrumentS en acIer
Steel instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated cutting blade geo-metry and cutter designs ensure a long ser-vice life and high cutting capacity when prepa-ring stone, acrylic, metal and precious metal.
Instruments specifically tailored to the relevant material and technique.
Öffnen oder Vertiefen der HauptfissurenOpen or deepen the dissectional fissuresOuverture et approfondissement des sillons principaux
Für Fissuren, kleine Korrekturen an Innenflä-chenFor fissures, minor corrections on inside sur-facesPour sillions, menues corrections des intrados
In Hohlkehlen und angrenzenden FlächenIn bevels and adjacent surfacesDans les congés creux et sur les surfaces avoisinantes
Instruments en acier pour des travaux de précision
Pour un retrait optimal du matériau et une qua-lité de surface fine.
Grande longévité et capacité de coupe éle-vée pour le traitement du plâtre, de la résine, du métal, et du métal précieux grâce à une denture adaptée optimale et aux formes des fraises.
Instruments spécialement adaptés pour les matériaux et travaux correspondants.
Stahlinstrumente für präzise arbeitsergebnisse
Für optimalen Materialabtrag und feine Ober-flächengüte.
Hohe Standzeiten und Schneidleistungen beim Bearbeiten von Gips, Kunststoff, Metall und Edelmetall durch die optimal abgestimm-ten Verzahnungen und Fräserformen.
Instrumente speziell auf die jeweiligen Werk-stoffe und Arbeiten abgestimmt.
Abrunden scharfer Kanten und Glätten okklu-saler KonturenTake off sharp edges and smoothen occlusal surfacesAdoucissement de bords tranchants et lissage des contours occlusaux
74
Stahlbohrer • Steel burS • InStrumentS en acIer
Steel instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated cutting blade geo-metry and cutter designs ensure a long ser-vice life and high cutting capacity when prepa-ring stone, acrylic, metal and precious metal.
Instruments specifically tailored to the relevant material and technique.
Öffnen oder Vertiefen der HauptfissurenOpen or deepen the dissectional fissuresOuverture et approfondissement des sillons principaux
Für Fissuren, kleine Korrekturen an Innenflä-chenFor fissures, minor corrections on inside sur-facesPour sillions, menues corrections des intrados
In Hohlkehlen und angrenzenden FlächenIn bevels and adjacent surfacesDans les congés creux et sur les surfaces avoisinantes
Instruments en acier pour des travaux de précision
Pour un retrait optimal du matériau et une qua-lité de surface fine.
Grande longévité et capacité de coupe éle-vée pour le traitement du plâtre, de la résine, du métal, et du métal précieux grâce à une denture adaptée optimale et aux formes des fraises.
Instruments spécialement adaptés pour les matériaux et travaux correspondants.
Stahlinstrumente für präzise arbeitsergebnisse
Für optimalen Materialabtrag und feine Ober-flächengüte.
Hohe Standzeiten und Schneidleistungen beim Bearbeiten von Gips, Kunststoff, Metall und Edelmetall durch die optimal abgestimm-ten Verzahnungen und Fräserformen.
Instrumente speziell auf die jeweiligen Werk-stoffe und Arbeiten abgestimmt.
Abrunden scharfer Kanten und Glätten okklu-saler KonturenTake off sharp edges and smoothen occlusal surfacesAdoucissement de bords tranchants et lissage des contours occlusaux
VARIOstar K50/D50 BRUSHLESS HANDPIECE
Rotation speed indicator
Easy to read and continuous
Speed knob
To set desired max speed
Direction switch
To select forward/reverse
Digital speed display
Easy to read
Tool tray
Knee Control
Foot Control
Safety switch
Unlock the max rotation speed
Right hand rotation (+)
Button to increase the max rotation speed
Left hand rotation (–)
Button to reduce the max rotation speed
Speed control
Steel Burs
CALL US ON
01494 448474
FOR PRICES
£740.75SZU040
£729.50SZU039
1676
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
Steel Burs
L mmSize 1/10 mm 005 006 007 008 009 010 012 014 016 018
SHANK Order No. SET087 SET088 SET089 SET090 SET091 SET092 SET093 SET094 SET095 SET096
↻max. 50,000
1Round
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
1Round
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
2Inverted Cone
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
3Wheel
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
21Cylinder
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
L mm
Size 1/10 mm 021 023 025 027 029 031 033 035 037 040
SHANK Order No. SET097 SET098 SET099 SET100 SET101 SET102 SET103 SET104 SET105 SET106
↻max. 30,000 25,000 20,000
L mm
Size 1/10 mm 006 007 008 009 010 012 014 016 018 021 023
SHANK Order No. SET111 SET112 SET113 SET114 SET115 SET116 SET117 SET118 SET119 SET120 SET121
↻max. 50,000 30,000
L mm
Size 1/10 mm 006 007 008 009 010 012 014 016 018 021 023
SHANK Order No. SET140 SET141 SET142 SET143 SET144 SET145 SET146 SET147 SET148 SET149 SET150
↻max. 50,000 30,000
L mm 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Size 1/10 mm 008 008 010 012 014 016 018 021 023
SHANK Order No. SET140 SET141 SET142 SET143 SET144 SET145 SET146 SET147 SET148
↻max. 50,000 30,000
17 77
Stahlbohrer • Steel burS • InStrumentS en acIer
L mm 4,2 4,5 4,8 5,1Grösse • Size • Tailles 1/10 mm 010 012 014 016
US No. 957 958 959 960Shank ISO Order No. HP 310 104 150 001... 207.104... 010 012 014 016
dmax. 50.000
207Zylinder, stirnschneidendCylinder, End CuttingCylindre, coupe frontalep 6
L mm 3,0 3,3 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023
US No. 556 557 558 559 560 561 562 563Shank ISO Order No. HP 310 104 107 002... 36.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
36ZylinderCylinderCylindrep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 169 170 171 172 173Shank ISO Order No. HP 310 104 168 006... 23.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
23KonischTapered FissureConiquep 6
L mm 3,3 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 007 008 009 010 012 014 016 018 021 023
US No. 699 700 701 702 703Shank ISO Order No. HP 310 104 168 002... 38.104... 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
38KonischTapered FissureConiquep 6
Steel Burs
207Cylinder, End Cutting
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
36Cylinder
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
23Tapered Fissure
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
38Tapered Fissure
6
76
Stahlbohrer • Steel burS • InStrumentS en acIer
Grösse • Size • Tailles 1/10 mm 005 006 007 008 009 010 012 014 016 018 US No. ¼ ½ 1 2 3 4 5 6
Shank ISO Order No. HP 310 104 001 001... 1.104... 005 006 007 008 009 010 012 014 016 018
dmax. 50.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 021 023 025 027 029 031 033 035 037 040 US No. 7 8 9 11
Shank ISO Order No. HP 310 104 001 001... 1.104... 021 023 025 027 029 031 033 035 037 040
dmax. 30.000 25.000 20.000
1KugelRoundBoulep 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 33 ½ 34 35 36 37 38 39 40 41
Shank ISO Order No. HP 310 104 010 001... 2.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
2Umgekehrter KegelInverted ConeCône renversép 6
Grösse • Size • Tailles 1/10 mm 006 007 008 009 010 012 014 016 018 021 023 US No. 11 ½ 12 14 16
Shank ISO Order No. HP 310 104 040 001... 3.104... 006 007 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
3RadWheelRouep 6
L mm 3,6 3,9 4,2 4,5 4,8 5,1 5,4 5,7 6,0Grösse • Size • Tailles 1/10 mm 008 009 010 012 014 016 018 021 023
US No. 56 57 58 59 60 61 62 63Shank ISO Order No. HP 310 104 107 006... 21.104... 008 009 010 012 014 016 018 021 023
dmax. 50.000 30.000
21ZylinderCylinderCylindrep 6
L mm 4.2 4.5 4.8 5.1
Size 1/10 mm 010 012 014 016
SHANK Order No. SET107 SET108 SET109 SET100
↻max. 50,000
L mm 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Size 1/10 mm 006 007 008 009 010 012 014 016 018 021 023
SHANK Order No. SET151 SET152 SET153 SET154 SET155 SET156 SET157 SET158 SET159 SET160 SET161
↻max. 50,000 30,000
L mm 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Size 1/10 mm 008 009 010 012 014 016 018 021 023
SHANK Order No. SET131 SET132 SET133 SET134 SET135 SET136 SET137 SET138 SET139
↻max. 50,000 30,000
L mm 3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7 6.0
Size 1/10 mm 007 008 009 010 012 014 016 018 021 023
SHANK Order No. SET162 SET163 SET164 SET165 SET166 SET167 SET168 SET169 SET170 SET171
↻max. 50,000 30,000
SKILLDENTA PRICES EXCLUDE VAT & CARRIAGE, VALID FROM 31/05/2016. SUBJECT TO AVAILABILITY - E & OE. IMAGES ARE NOT TO SCALE
CALL US ON
01494 448474
FOR PRICES
18
Art. No. Description Application
266
266R
354R
3680 / 3681
3780 / 3781
2635
2636
2660
2666
2666 F
2936
2966
2966F
3266
2436
2466
2466 F
2535
2536
2566
2566 F
3870
C33L
3982
4060
7800
7995
Cylindrical Wax Carver
Cylindrical Wax Carver, round
Cylindrical Wax Cutter, round
Parallel Wax Cutter
Tapered Wax Cutter
Parallel Cutter, cross-cut, coarse, round end
Parallel Cutter, cross-cut, round end
Parallel Cutter, plain cut, round end, right
Parallel Cutter, plain cut, round end, left
Parallel cutter plain cut, left twist with chamfer ground section
Parallel Cutter, cross-cut, flat end
Parallel Cutter, plain cut, flat end, left
Parallel Cutter with chamfer ground section, plain cut, flat end, left twist
Parallel Cutter, plain, end-cutting, flat end
Conical Cutter, cross-cut, flat end
Conical Cutter, plain cut, flat end
Cone Cutter, plain cut, flat end
Cone cutter cross cut coarse, round end
Conical Cutter, cross-cut, round end
Conical Cutter, plain cut, round end
Cone cutter plain cut, round end
Channel Cutter
Channel Cutter
Tube Drill
Shoulder Cutter
Twist Drill
Centring Drill
Wax trimming ➫ for milling patterns
Wax trimming ➫ for milling patterns
Wax trimming ➫ for milling patterns
Parallel attachment patterns
Conical attachment patterns – 3.000 rpm
Pre-milling on precious metal attachments
Pre-milling on precious metal attachments – 10.000 rpm
Fine Milling, for dressing
Fine Milling, for dressing
Fine Milling, for dressing
Pre-milling on precious metal attachments
Fine Milling, for dressing
Fine Milling, for dressing and finishing – 6.000 rpm
Fine Milling, for dressing
Conical precious metal crowns – 10.000 rpm
Detto, for dressing
Detto, for dressing
Pre - milling on conical crowns
Conical precious metal crowns – 10.000 rpm
Detto, for dressing
Detto, for dressing
Attachment pattern: channel cutting – 3.000 rpm
Attachment pattern: channel cutting
Smoothing of drilling walls
Counter-boring on concentric attachment shoulder – 3.000 rpm
Hole drilling on attachments – 10.000 rpm
Drill spot marking on attachments – 5.000 rpm
19
Milling Technique
C33LChannel cutter↻ 5.000 - 10.000
1
266RWax trimmer cylindrical round
1
266Wax trimmer cylindrical
1
1 354RWax cutter cylindrical round↻ 3.000
1
2436Cone cutter cross cut, flat end↻ 5.000 - 10.000
1
2466FCone cutter plain cut, chamfer ground section↻ 6.000
1 2535Cone cutter cross cut coarse, round end↻ 5.000 - 10.000
1
2536Cone cutter cross cut, round end↻ 5.000 - 10.000
1 2566Cone cutter plain cut, round end↻ 3.000 - 5.000
1
2466Cone cutter plain cut coarse, flat end↻ 3.000 - 5.000
1
L mm 6,0
Size 1/10 mm 010
Order No. SET1150
Shank:103 HP 2,35mm
L mm 17,0
Size 1/10 mm 023
Order No. SET1096
Shank:123 HP 3,00mm
L mm 17,0
Size 1/10 mm 023
Order No. SET1097
Shank:103 HP 2,35mm
Order No. SET1098
Shank:123 HP 3,00mm
L mm 10,0 15,0
Size 1/10 mm 015 023
Order No. SET1062 SET1063
Shank:103 HP 2,35mm
Order No. SET1064 SET1065
Shank:123 HP 3,00mm
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1129 SET1130 SET1131
Shank:103 HP 2,35mm
Order No. SET1132 – –
Shank:123 HP 3,00mm
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1140 SET1141 SET1142
Shank:103 HP 2,35mm
Order No. SET1143 SET1144 SET1145
Shank:123 HP 3,00mm
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET750 SET751 SET752
Shank:103 HP 2,35mm
Order No. SET1153 SET1154 SET710
Shank:123 HP 3,00mm
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1135 SET1136 SET1137
Shank:103 HP 2,35mm
Order No. SET1138 SET1139 SET709
Shank:123 HP 3,00mm
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1067 SET1068 SET1069
Shank:103 HP 2,35mm
Order No. SET1070 SET1071 SET1072
Shank:123 HP 3,00mm
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1078 SET1079 SET1080
Shank:103 HP 2,35mm
Order No. SET1081 SET1082 SET1083
Shank:123 HP 3,00mm
20
2666 FParallel cutter plain cut, left twist with chamfer ground section ↻ 6.000
2966Parallel cutter plain cut, left twist, flat end↻ 3.000 - 5.000
2936Parallel cutter cross cut, flat end↻ 5.000 - 10.000
2966FParallel cutter, chamfer ground section↻ 6.000
3266Parallel cutter plain cut, left twist, end cutting↻ 3.000 - 5.000
2635Parallel cutter cross cut coarse, round end↻ 5.000 - 10.000
1
2636Parallel cutter cross cut, round end↻ 5.000 - 10.000
1 2660Parallel cutter plain cut, right twist, round end↻ 3.000 - 5.000
1
2666Parallel cutter plain cut, left twist, round end↻ 3.000 - 5.000
1
1 1
1 1
1 1
1 1
1 1
2566FCone cutter plain cut, chamfer ground section↻ 6.000
1
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1073 SET1074 SET1075
Shank:103 HP 2,35mm
Order No. SET1076 SET1077 SET711
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1084 SET1085 SET756
Shank:103 HP 2,35mm
Order No. SET1086 SET1087 SET1088
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1089 SET1090 SET1091
Shank:103 HP 2,35mm
Order No. SET1092 SET1093 SET1094
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1108 SET1109 SET1110
Shank:103 HP 2,35mm
Order No. SET1111 SET1112 SET1113
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1114 SET759 SET1115
Shank:103 HP 2,35mm
Order No. SET1116 – –
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1125 SET1126 SET1127 SET1128
Shank:103 HP 2,35mm
Order No. – SET715 SET716 SET717
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1119 SET1120 SET1121
Shank:103 HP 2,35mm
Order No. – SET1123 SET1124
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1066 SET758 SET757
Shank:103 HP 2,35mm
Order No. SET718 SET719 SET720
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1102 SET1103 SET1104
Shank:103 HP 2,35mm
Order No. SET1105 SET1106 SET1107
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1099 SET1100 SET714
Shank:103 HP 2,35mm
Order No. SET712 SET713 SET1101
Shank:123 HP 3,00mm
21
3780Wax cutter, conical round↻ 3.000
3870Channel Cutter↻ 5.000 - 10.000
7800Twist Drill↻ 5.000 - 10.000
3781Wax cutter tapered↻ 3.000
3680Wax cutter, parallel round↻ 3.000
1 3681Parallel wax cutter↻ 3.000
1
1 1
1
3982Tube Drill ↻ 3.000 - 5.000
1 4060Shoulder Cutter ↻ 3.000 - 5.000
1
1
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1051 SET1052 SET1053
Shank:103 HP 2,35mm
Order No. SET723 SET1054 SET1055
Shank:123 HP 3,00mm
L mm 13,0 13,0 13,0
Size 1/10 mm 023 031 040Winkel Angle 2° 4° 6°
Order No. SET1056 SET1057 SET1058
Shank:103 HP 2,35mm
Order No. SET1059 SET1060 SET1061
Shank:123 HP 3,00mm
L mm 5,0 5,0 5,0
Size 1/10 mm 027 029 032Winkel Angle 2° 4° 6°
Order No. SET1020 SET745 SET1021
Shank:103 HP 2,35mm
Order No. – SET1023 SET1024
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1041 SET1042 SET1043
Shank:103 HP 2,35mm
Order No. SET721 SET1044 SET1045
Shank:123 HP 3,00mm
L mm 7,0 8,0 8,0 8,0 8,0
Size 1/10 mm 007 010 012 015 020
Order No. SET1025 SET1026 SET1027 SET1028 SET1029
Shank:103 HP 2,35mm
Order No. SET1030 SET1031 SET1032 SET1033 SET1034
Shank:123 HP 3,00mm
L mm 7,5 9,0 12,0
Size 1/10 mm 007 010 012
Order No. SET1035 SET1036 SET1037
Shank:103 HP 2,35mm
Order No. SET1038 SET1038 SET1040
Shank:123 HP 3,00mm
L mm 8,0 8,0 9,0 9,0 12,0 12,0
Size 1/10 mm 007 008 009 010 012 015
Order No. SET1000 SET1001 SET1002 SET1003 SET1004 SET1005
Shank:103 HP 2,35mm
Order No. SET1006 SET1007 SET1008 SET1009 SET1010 –
Shank:123 HP 3,00mm
L mm 8,0 10,0 15,0
Size 1/10 mm 010 015 023
Order No. SET1046 SET1047 SET1048
Shank:103 HP 2,35mm
Order No. SET722 SET1049 SET1050
Shank:123 HP 3,00mm
22
Milling Set Order No. SET1151 ( 2,35 mm)Milling Set Order No. SET1152 ( 3,00 mm)
7995Centring Drill↻ 5.000 - 10.000
1
Conus Polisher special polisher for the milling technique on crown cores brown: pre-polishing 5.000 rpmgreen: high-gloss polishing 3.000 rpm
Types of shanks ISO 6360Milling technique103 - Handpiece short 2,35 mm123 - Handpiece short 3,00 mm
32 mm
123 3,00 mm
32 mm
103 2,35 mm
SET1104
Parallel Milling of a metal crown
SET1120
Parallel cutter with chamfer ground section
SET1091
Parallel Milling of a wax crown
6 / 100
L mm 5,0 5,0 5,0 5,0
Size 1/10 mm 009 010 012 014
Order No. SET1012 SET1013 SET1014 SET1015
Shank:103 HP 2,35mm
Order No. SET1016 SET1017 SET1018 SET1019
Shank:123 HP 3,00mm
L mm 12,0 12,0
Size 1/10 mm 140 140
Order No. SET1149 SET1147
CALL US ON
01494 448474
FOR PRICES
23
Occlusal fissuring and contouring
Shape margins and retention grooves on individual trays
Contouring of porcelain and composite veneers
Pre-separating and Contouring
Diamond rotary instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated diamond grit and instrument designs ensure a long service life and high cutting capacity when preparing and separating porcelain, facing composites and model materials.
Instruments specifically tailored to the relevant material and technique.
Diamond Intruments
Occlusal fissuring and contouring.
Pre-separating and contouring.
Shape margins and retention grooves on individual trays.
Contouring of porcelain and composite veneers.
Occlusal fissuring and contouring
Shape margins and retention grooves on individual trays
Contouring of porcelain and composite veneers
Pre-separating and Contouring
Diamond rotary instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated diamond grit and instrument designs ensure a long service life and high cutting capacity when preparing and separating porcelain, facing composites and model materials.
Instruments specifically tailored to the relevant material and technique.
Occlusal fissuring and contouring
Shape margins and retention grooves on individual trays
Contouring of porcelain and composite veneers
Pre-separating and Contouring
Diamond rotary instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated diamond grit and instrument designs ensure a long service life and high cutting capacity when preparing and separating porcelain, facing composites and model materials.
Instruments specifically tailored to the relevant material and technique.
Occlusal fissuring and contouring
Shape margins and retention grooves on individual trays
Contouring of porcelain and composite veneers
Pre-separating and Contouring
Diamond rotary instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated diamond grit and instrument designs ensure a long service life and high cutting capacity when preparing and separating porcelain, facing composites and model materials.
Instruments specifically tailored to the relevant material and technique.
Occlusal fissuring and contouring
Shape margins and retention grooves on individual trays
Contouring of porcelain and composite veneers
Pre-separating and Contouring
Diamond rotary instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated diamond grit and instrument designs ensure a long service life and high cutting capacity when preparing and separating porcelain, facing composites and model materials.
Instruments specifically tailored to the relevant material and technique.
Occlusal fissuring and contouring
Shape margins and retention grooves on individual trays
Contouring of porcelain and composite veneers
Pre-separating and Contouring
Diamond rotary instruments for precise preparation
Optimum material reduction and a high-quality surface finish.
The optimally coordinated diamond grit and instrument designs ensure a long service life and high cutting capacity when preparing and separating porcelain, facing composites and model materials.
Instruments specifically tailored to the relevant material and technique.
Dentalfarm HP45 Multifunction Bench top brush micromotor
Bench-top micromotor featuring a compact, heavy-duty control unit and ergonomic 35.000rpm handpiece.
Bench-top micromotor featuring a compact, heavy-duty control unit and ergonomic 45.000rpm handpiece.
Dentalfarm HP35 On-OffBench top brush micromotor
£273.75SCI657
£195.00SCI656
DENTALFARM BENCH TOP MICROMOTORS
2480
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
801Round
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
HP Diamonds
805Inverted Cone
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
807Inverted Cone
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
808Inverted Cone
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
809Inverted Cone with collar
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
812Inverted Cone, side-coated
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
818Wheel
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
825Knife Edge
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
L mm
Size 1/10 mm 009 010 012 014 016 018 021 023 029 035
Order No. SET426 SET427 SET428 SET429 SET430 SET431 SET432 SET433 SET434 SET435
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0
Size 1/10 mm 012 014 016 018 021 023 040 050
Order No. SET437 SET438 SET439 SET440 SET441 SET442 SET443 SET444
L mm 4,0 5,0 6,0
Size 1/10 mm 016 018 023
Order No. SET447 SET448 SET449
L mm 0,7 0,8
Size 1/10 mm 018 023
Order No. SET453 SET454
L mm 3,5
Size 1/10 mm 023
Order No. SET456
L mm 1,0
Size 1/10 mm 033
Order No. SET462
L mm 1,5 2,0
Size 1/10 mm 025 050
Order No. SET458 SET460
L mm 0,8 0,9 1,1 1,5
Size 1/10 mm 018 025 040 050
Order No. SET467 SET468 SET469 SET470
CALL US ON
01494 448474
FOR PRICES
25
81
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 12,5Shank ISO Order No. HP • 806 104 238 544... 5830.104... 070
830
BirnePearPoire
p 3
L mm 4,0 4,0 4,0 4,0 5,0 6,0Shank ISO Order No.HP 806 104 109 524... 835.104... 008 010 012 016 021 025
835
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 9,0Shank ISO Order No. HP 806 104 184 524... 848A.104... 040
848A
Konus flach, seitenbelegtFlat End Taper, side-coatedCône, bout plat, diamanté sur les faces travaillantes
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 111 524... 837.104... 016 018
837
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 8,0 9,0 7,0Shank ISO Order No. HP 806 104 111 524... 840.104... 033 040 050
840
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 15,0Shank ISO Order No. HP • 806 104 158 534... 6842KR.104... 023
842KR
Zylinder, Kante rundRound Edge CylinderCylindre, bord arrondi
p 3L mm 12,0
Shank ISO Order No. HP 806 104 143 524... 842R.104... 018
• 806 104 143 534... 6842R.104... 018
842R
Zylinder rundRound End CylinderCylindre, bout arrondi
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 172 524... 847.104... 025 033
847
Konus flachFlat End TaperCône, bout plat
p 3
L mm 4,0 4,0 5,0Shank ISO Order No. HP 806 104 170 524... 845.104... 008 010 018
845
Konus flachFlat End TaperCône, bout plat
p 3
81
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 12,5Shank ISO Order No. HP • 806 104 238 544... 5830.104... 070
830
BirnePearPoire
p 3
L mm 4,0 4,0 4,0 4,0 5,0 6,0Shank ISO Order No.HP 806 104 109 524... 835.104... 008 010 012 016 021 025
835
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 9,0Shank ISO Order No. HP 806 104 184 524... 848A.104... 040
848A
Konus flach, seitenbelegtFlat End Taper, side-coatedCône, bout plat, diamanté sur les faces travaillantes
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 111 524... 837.104... 016 018
837
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 8,0 9,0 7,0Shank ISO Order No. HP 806 104 111 524... 840.104... 033 040 050
840
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 15,0Shank ISO Order No. HP • 806 104 158 534... 6842KR.104... 023
842KR
Zylinder, Kante rundRound Edge CylinderCylindre, bord arrondi
p 3L mm 12,0
Shank ISO Order No. HP 806 104 143 524... 842R.104... 018
• 806 104 143 534... 6842R.104... 018
842R
Zylinder rundRound End CylinderCylindre, bout arrondi
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 172 524... 847.104... 025 033
847
Konus flachFlat End TaperCône, bout plat
p 3
L mm 4,0 4,0 5,0Shank ISO Order No. HP 806 104 170 524... 845.104... 008 010 018
845
Konus flachFlat End TaperCône, bout plat
p 3
L mm 12.5
Order No. SET472PRICE £36.31
L mm 4.0 4.0 5.0
Order No. SET... 489 490 494PRICE £5.95 £5.95 £6.57
830Pear
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
835Flat End Cylinder
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
837Flat End Cylinder
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
845Flat End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
848AFlat End Taper, side-coated
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
847Flat End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
840Flat End Cylinder
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
81
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 12,5Shank ISO Order No. HP • 806 104 238 544... 5830.104... 070
830
BirnePearPoire
p 3
L mm 4,0 4,0 4,0 4,0 5,0 6,0Shank ISO Order No.HP 806 104 109 524... 835.104... 008 010 012 016 021 025
835
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 9,0Shank ISO Order No. HP 806 104 184 524... 848A.104... 040
848A
Konus flach, seitenbelegtFlat End Taper, side-coatedCône, bout plat, diamanté sur les faces travaillantes
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 111 524... 837.104... 016 018
837
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 8,0 9,0 7,0Shank ISO Order No. HP 806 104 111 524... 840.104... 033 040 050
840
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 15,0Shank ISO Order No. HP • 806 104 158 534... 6842KR.104... 023
842KR
Zylinder, Kante rundRound Edge CylinderCylindre, bord arrondi
p 3L mm 12,0
Shank ISO Order No. HP 806 104 143 524... 842R.104... 018
• 806 104 143 534... 6842R.104... 018
842R
Zylinder rundRound End CylinderCylindre, bout arrondi
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 172 524... 847.104... 025 033
847
Konus flachFlat End TaperCône, bout plat
p 3
L mm 4,0 4,0 5,0Shank ISO Order No. HP 806 104 170 524... 845.104... 008 010 018
845
Konus flachFlat End TaperCône, bout plat
p 3
81
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 12,5Shank ISO Order No. HP • 806 104 238 544... 5830.104... 070
830
BirnePearPoire
p 3
L mm 4,0 4,0 4,0 4,0 5,0 6,0Shank ISO Order No.HP 806 104 109 524... 835.104... 008 010 012 016 021 025
835
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 9,0Shank ISO Order No. HP 806 104 184 524... 848A.104... 040
848A
Konus flach, seitenbelegtFlat End Taper, side-coatedCône, bout plat, diamanté sur les faces travaillantes
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 111 524... 837.104... 016 018
837
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 8,0 9,0 7,0Shank ISO Order No. HP 806 104 111 524... 840.104... 033 040 050
840
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 15,0Shank ISO Order No. HP • 806 104 158 534... 6842KR.104... 023
842KR
Zylinder, Kante rundRound Edge CylinderCylindre, bord arrondi
p 3L mm 12,0
Shank ISO Order No. HP 806 104 143 524... 842R.104... 018
• 806 104 143 534... 6842R.104... 018
842R
Zylinder rundRound End CylinderCylindre, bout arrondi
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 172 524... 847.104... 025 033
847
Konus flachFlat End TaperCône, bout plat
p 3
L mm 4,0 4,0 5,0Shank ISO Order No. HP 806 104 170 524... 845.104... 008 010 018
845
Konus flachFlat End TaperCône, bout plat
p 3
81
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 12,5Shank ISO Order No. HP • 806 104 238 544... 5830.104... 070
830
BirnePearPoire
p 3
L mm 4,0 4,0 4,0 4,0 5,0 6,0Shank ISO Order No.HP 806 104 109 524... 835.104... 008 010 012 016 021 025
835
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 9,0Shank ISO Order No. HP 806 104 184 524... 848A.104... 040
848A
Konus flach, seitenbelegtFlat End Taper, side-coatedCône, bout plat, diamanté sur les faces travaillantes
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 111 524... 837.104... 016 018
837
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 8,0 9,0 7,0Shank ISO Order No. HP 806 104 111 524... 840.104... 033 040 050
840
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 15,0Shank ISO Order No. HP • 806 104 158 534... 6842KR.104... 023
842KR
Zylinder, Kante rundRound Edge CylinderCylindre, bord arrondi
p 3L mm 12,0
Shank ISO Order No. HP 806 104 143 524... 842R.104... 018
• 806 104 143 534... 6842R.104... 018
842R
Zylinder rundRound End CylinderCylindre, bout arrondi
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 172 524... 847.104... 025 033
847
Konus flachFlat End TaperCône, bout plat
p 3
L mm 4,0 4,0 5,0Shank ISO Order No. HP 806 104 170 524... 845.104... 008 010 018
845
Konus flachFlat End TaperCône, bout plat
p 3
81
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 12,5Shank ISO Order No. HP • 806 104 238 544... 5830.104... 070
830
BirnePearPoire
p 3
L mm 4,0 4,0 4,0 4,0 5,0 6,0Shank ISO Order No.HP 806 104 109 524... 835.104... 008 010 012 016 021 025
835
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 9,0Shank ISO Order No. HP 806 104 184 524... 848A.104... 040
848A
Konus flach, seitenbelegtFlat End Taper, side-coatedCône, bout plat, diamanté sur les faces travaillantes
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 111 524... 837.104... 016 018
837
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 8,0 9,0 7,0Shank ISO Order No. HP 806 104 111 524... 840.104... 033 040 050
840
Zylinder flachFlat End CylinderCylindre, bout plat
p 3
L mm 15,0Shank ISO Order No. HP • 806 104 158 534... 6842KR.104... 023
842KR
Zylinder, Kante rundRound Edge CylinderCylindre, bord arrondi
p 3L mm 12,0
Shank ISO Order No. HP 806 104 143 524... 842R.104... 018
• 806 104 143 534... 6842R.104... 018
842R
Zylinder rundRound End CylinderCylindre, bout arrondi
p 3
L mm 7,0 8,0Shank ISO Order No. HP 806 104 172 524... 847.104... 025 033
847
Konus flachFlat End TaperCône, bout plat
p 3
L mm 4,0 4,0 5,0Shank ISO Order No. HP 806 104 170 524... 845.104... 008 010 018
845
Konus flachFlat End TaperCône, bout plat
p 3
842RRound Edge Cylinder
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
HP Diamonds
L mm 4,0 4,0 4,0 4,0
Size 1/10 mm 008 010 012 014
Order No. SET473 SET475 SET476 SET478
L mm 12,5
Size 1/10 mm 070
Order No. SET472
L mm 7,0 8,0
Size 1/10 mm 016 018
Order No. SET481 SET482
L mm 12,0
Size 1/10 mm 018
Order No. SET487
L mm 4,0 4,0 4,0
Size 1/10 mm 008 010 018
Order No. SET489 SET490 SET491
L mm 9,0
Size 1/10 mm 040
Order No. SET499
L mm 7,0 8,0
Size 1/10 mm 025 033
Order No. SET495 SET496
L mm 8,0 8,0 7,0
Size 1/10 mm 033 040 050
Order No. SET483 SET484 SET485
2682
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 10,0 9,0Shank ISO Order No. HP 806 104 173 524... 848.104... 018 040
• 806 104 173 534... 6848.104... 018
848
Konus flachFlat End TaperCône, bout plat
p 3
L mm 15,0Shank ISO Order No. HP • 806 104 175 534... 6848L.104... 023
• 806 104 175 544... 5848L.104... 023
848L
Konus langTaper longCône, long
p 3
L mm 4,0Shank ISO Order No. HP 806 104 196 524... 849.104... 009
849
Konus rundRound End TaperCône, bout arrondi
p 3
L mm 10,0 10,0 9,0Shank ISO Order No. HP 806 104 199 524... 850.104... 014 025 040
• 806 104 199 534... 6850.104... 025
850
Konus rundRound End TaperCône, bout arrondi
p 3
L mm 4,0 6,0 7,0Shank ISO Order No. HP 806 104 164 524... 852.104... 010 023 037
852
Konus SpitzeX-mas TreeCône, pointu
p 3
L mm 8,0Shank ISO Order No. HP 806 104 172 524... 854.104... 050
854
Konus flachFlat End TaperCône, bout plat
p 3
L mm 9,0 9,0Shank ISO Order No. HP 806 104 198 524... 854R.104... 033 040
854R
Konus rundRound End TaperCône, bout arrondi
p 3
L mm 7,0 12,0 8,0 14,0Shank ISO Order No. HP 806 104 198 524... 856.104... 016 025
• 806 104 198 534... 6856.104... 023 040• 806 104 198 544... 5856.104... 023 040
856
Konus rundRound End TaperCône, bout arrondi
p 3
L mm 8,0 8,0Shank ISO Order No. HP • 806 104 165 514... 8858.104... 016
806 104 165 524... 858.104... 012 016
858
Konus SpitzeNeedleCône, pointu
p 3
L mm 10,0Shank ISO Order No. HP • 806 104 166 514... 8859.104... 018
806 104 166 524... 859.104... 018
859
Konus SpitzeNeedleCône, pointu
p 3
L mm 10.0 9.0
Order No. SET...
£
L mm 10.0 9.0
Size 1/10 mm 018 040
SHANK SET... 497 498HP PRICE £13.52 £27.14
848Flat End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
849Round End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
852Xmas Tree
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
854RRound End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
858Needle
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
859Needle
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
856Round End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
854Flat End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
850Round End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
848LTaper Long
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
HP Diamonds
L mm 10,0 9,0
Size 1/10 mm 018 040
Order No. SET497 SET498
L mm 15,0
Size 1/10 mm 023
Order No. SET500
L mm 4,0
Size 1/10 mm 009
Order No. SET501
L mm 10,0 10,0 9,0
Size 1/10 mm 014 025 040
Order No. SET505 SET506 SET507
L mm 4,0 6,0 7,0
Size 1/10 mm 010 023 037
Order No. SET508 SET509 SET510
L mm 9,0 9,0
Size 1/10 mm 033 040
Order No. SET513 SET514
L mm 8,0 8,0
Size 1/10 mm 012 016
Order No. SET519 SET520
L mm 10,0
Size 1/10 mm 018
Order No. SET521
L mm 7,0 12,0 8,0 14,0
Size 1/10 mm 016 023 025 040
Order No. SET515 SET516 SET517 SET518
L mm 8,0
Size 1/10 mm 050
Order No. SET512
27 83
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
L mm 4,0 5,0 5,0Shank ISO Order No. HP 806 104 247 524... 860.104... 010 012 016
860
FlammeFlameFlamme
p 3
L mm 12,5Shank ISO Order No. HP • 806 104 251 544... 5860.104... 060
860
FlammeFlameFlamme
p 3
L mm 10,0 10,0Shank ISO Order No. HP 806 104 250 524... 863.104... 012 016
• 806 104 250 534... 6863.104... 012 016
863FlammeFlameFlamme
p 3
L mm 7,0 7,0 9,0Shank ISO Order No. HP 806 104 141 524... 881.104... 016 025 040
881Zylinder rundRound End Cylinder, Cylindre, bout arrondi
p 3
L mm 6,0Shank ISO Order No. HP 806 104 248 524... 861.104... 014
861FlammeFlameFlamme
p 3
L mm 14,0Shank ISO Order No. HP • 806 104 274 544... 5862.104... 060
862FlammeFlameFlamme
p 3
L mm 2,0Shank ISO Order No. HP 806 104 068 524... 909.104... 050
909RadRound WheelRoue
p 3
L mm 3,5Shank ISO Order No. HP 806 104 245 524... 890.104... 016
890FlammeFlameFlamme
p 3
L mm 5,0Shank ISO Order No. HP 806 104 257 524... 368.104... 023
368KnospePointed BudBouton pointu
p 3
L mm 1,8 2,5Shank ISO Order No. HP 806 104 257 524... 366.104... 012 016
366KnospePointed BudBouton pointu
p 3
L mm 12,0Shank ISO Order No. HP • 806 104 263 544... 5369.104... 070
369Konus rundRound End TaperCône, bout arrondi
p 3
Turbo DIAMANTeN • Turbo DIAMoNDs • DIAMANTs Turbo
L mm 15,0Shank ISO Order No. HP • 806 104 175 544... T5848L.104... 023
T848LKonus langTaper longCône long
p 3
L mm 12,0Shank ISO Order No. HP • 806 104 200 544... T5856.104... 023
T856Konus rundRound End TaperCône, bout arrondi
p 3
L mm 5.0
Order No. SET541PRICE £10.81
860Flame
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
861Flame
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
863Flame
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
890Flame
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
366Pointed Bud
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
369Round End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
T848LTaper Long
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
T856Round End Taper
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
368Pointed Bud
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
909Round Wheel
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
881Round Cut Cylinder
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
860Flame
3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
Turbo Diamonds
HP Diamonds
L mm 4,0 5,0
Size 1/10 mm 010 012
Order No. SET522 SET523
L mm 12,5
Size 1/10 mm 060
Order No. SET526
L mm 6,0
Size 1/10 mm 014
Order No. SET527
L mm 10,0 10,0
Size 1/10 mm 012 016
Order No. SET529 SET530
L mm 3,5
Size 1/10 mm 016
Order No. SET535
L mm 1,8 2,5
Size 1/10 mm 012 016
Order No. SET539 SET540
L mm 12,0
Size 1/10 mm 070
Order No. SET542
L mm 15,0
Size 1/10 mm 023
Order No. SET544
L mm 12,0
Size 1/10 mm 023
Order No. SET545
L mm 5,0
Size 1/10 mm 023
Order No. SET541
L mm 2,0
Size 1/10 mm 050
Order No. SET538
L mm 7,0 7,0 9,0
Size 1/10 mm 016 025 040
Order No. SET532 SET533 SET534
2886
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
Die natur-Diamanten der White-TIGER Dia-mantinstru mente sind durch ein patentiertes LLD – Herstellungsverfahren mehrschich-tig und dauerhaft auf dem rostfreien Schaft gebunden.
Die hohe Qualität dieser Diamant-Instru-mente bietet dem Anwender viele Vorteile gegenüber dem Arbeiten mit Standard - Dia-mantinstrumenten und führt zu optimalsten Ergebnissen.
hohe schleifleistung (1)
Durch das patentierte LLD - Bonding sowie die mehrschichtige Diamantierung ergibt sich ein schnellerer Abtransport der Schleifsub-stanz (hohe Schleifleistung) und damit auch ein kühles Schleifen.
glattes schliffbild (2)
Durch den raschen Abtransport der Schleif-substanz wird ein optimaler, vibrationsfrei-er Rundlauf der White-TIGER Instrumente erreicht (glattes Schliffbild).
The natural diamonds of the White-TIGER diamond instruments are multi-layered and permanently bonded to the stainless steel shank using a patented LLD manufacturing process.
The high quality of these diamond instru-ments offers the user many advantages compared to working with standard diamond instruments and leads to optimal results.
high cutting performance (1)
With the patented LLD bond and multi-layered diamond veneer, the tooth structure is reduced faster (high cutting performance), thus ensuring minimum heat generation when cutting.
smooth cut (2)
Conveying the debris away from the surface rapidly enables White-TIGER instruments to rotate concentrically and vibration-free (smooth cut).
Les particules de diamant naturel des instru-ments White-TIGER sont liées durable-ment et par couches multiples à la tige en acier inoxydable au moyen du procédé de fabrication breveté LLD. La grande quali-té de ces instruments diamantés permet à l’utilisateur de bénéficier de nombreux avan-tages par rapport au travail entrepris à l’aide d’instruments diamantés standards et condu-it à obtenir les résultats les plus optimaux.
fort pouvoir abrasif (1)
Le procédé de liaison breveté LLD ainsi que la diamantation multicouches ont pour effet une évacuation très rapide de la substance abrasée (fort pouvoir abrasif) et par consé-quent, un meulage s’effectuant à une tempé-rature plus basse.
etat lisse, surface abrasée (2)
Du fait de l’évacuation rapide de la sub-stance abrasée, la concentricité de l’instrument White-TIGER reste optimale et exempte de vibrations (état lisse de la sur-face abrasée).
höchste standzeit (3)
Durch das patentierte LLD-Bonding können die Diamantkörner nicht mehr herausgelöst werden. Dadurch erhöht sich die Standzeit der White-TIGER Diamantinstrumente um ein Mehrfaches. Bei Standard-Diamant-instru-menten lösen sich die Diamantkörner früh-zeitig aus der Bindung, was nur eine kurze Standzeit der Instrumente ergibt.
Anwendung
In der Keramik-/ Zirkonoxid Vollkeramik-BearbeitungKeramik- und Kunststoff-VerblendtechnikFeinbearbeitung von Vollkeramik undKompositenOkklusale Adjustierung auf Zirkonoxid -VollkeramikAufpassen von gesinterten Zirkonoxidge-rüsten und KronenAbtragen von Druckstellen an ZirkonoxidMaterialienOkklusales Konturieren und Fissuren-gestaltung
AnwendungshinwiseDas Beschleifen der Keramik-/ ZirkonoxidVollkeramik erfolgt unter Wasserkühlung mit der Laborturbine.nur mit leichtem Arbeitsdruck arbeiten Dre-zahlangaben einhalten.
Maximum life-span (3)
The LLD bond ensures that diamond particles no longer come loose. This increases the life span of the White-TIGER diamond instru-ments several times over. Using standard diamond instruments the diamond particles come loose much sooner from the bond resul-ting in a short life span of the instruments.
Application
Preparing porcelain/ zirconia all-porcelainPorcelain and composite facingsFine contouring of all-porcelain and compo-sitesOcclusal adjustments on zirconia all-porcelainFitting sintered zirconia frameworks and crownsRemoving high spots on zirconia restorationsContouring occlusal surfaces and preparing fissures
Instructions for usePorcelain / zirconia all-porcelain should be prepared with a laboratory turbine using water coolant.Use only minimum pressure when preparing and adhere to the recommended rpm.
extraordinaire durabilité (3)
Du fait de la liaison LLD brevetée, les particules de diamant ne peuvent plus se décoller. La durabilité des instruments White-TIGER est ainsi très fortement augmentée. Avec les instruments standards, les particules de diamant se détachent prématurément du liant ce qui a pour conséquence une faible durée de vie de ces instruments.
utilisationTraitement de la céramique / tout-céramique en oxyde de zirconiumTechnique de recouvrement avec de la céra-mique et de la résineTraitement précis du tout-céramique et des compositesAjustage occlusal du tout-céramique en oxyde de zirconiumAjustement d´armatures en oxyde de zirconi-um fritté et de couronnesElimination de points de pression sur les matériaux en oxyde de zirconiumContour occlusal et réalisation de fissures
recommandation pour l’utilisationLe fraisage de la céramique/tout-céramique en oxyde de zirconium se réalise sous irrigati-on d´eau avec une turbine de laboratoire.Travailler seulement avec une légère pression, respecter le nombre de tours.
conventionaldiamonds
WhiteTIger
cutting life
cutti
ng e
ffici
ency
llD - Bonding
Multilayer - Bonding
1 2 386
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
Die natur-Diamanten der White-TIGER Dia-mantinstru mente sind durch ein patentiertes LLD – Herstellungsverfahren mehrschich-tig und dauerhaft auf dem rostfreien Schaft gebunden.
Die hohe Qualität dieser Diamant-Instru-mente bietet dem Anwender viele Vorteile gegenüber dem Arbeiten mit Standard - Dia-mantinstrumenten und führt zu optimalsten Ergebnissen.
hohe schleifleistung (1)
Durch das patentierte LLD - Bonding sowie die mehrschichtige Diamantierung ergibt sich ein schnellerer Abtransport der Schleifsub-stanz (hohe Schleifleistung) und damit auch ein kühles Schleifen.
glattes schliffbild (2)
Durch den raschen Abtransport der Schleif-substanz wird ein optimaler, vibrationsfrei-er Rundlauf der White-TIGER Instrumente erreicht (glattes Schliffbild).
The natural diamonds of the White-TIGER diamond instruments are multi-layered and permanently bonded to the stainless steel shank using a patented LLD manufacturing process.
The high quality of these diamond instru-ments offers the user many advantages compared to working with standard diamond instruments and leads to optimal results.
high cutting performance (1)
With the patented LLD bond and multi-layered diamond veneer, the tooth structure is reduced faster (high cutting performance), thus ensuring minimum heat generation when cutting.
smooth cut (2)
Conveying the debris away from the surface rapidly enables White-TIGER instruments to rotate concentrically and vibration-free (smooth cut).
Les particules de diamant naturel des instru-ments White-TIGER sont liées durable-ment et par couches multiples à la tige en acier inoxydable au moyen du procédé de fabrication breveté LLD. La grande quali-té de ces instruments diamantés permet à l’utilisateur de bénéficier de nombreux avan-tages par rapport au travail entrepris à l’aide d’instruments diamantés standards et condu-it à obtenir les résultats les plus optimaux.
fort pouvoir abrasif (1)
Le procédé de liaison breveté LLD ainsi que la diamantation multicouches ont pour effet une évacuation très rapide de la substance abrasée (fort pouvoir abrasif) et par consé-quent, un meulage s’effectuant à une tempé-rature plus basse.
etat lisse, surface abrasée (2)
Du fait de l’évacuation rapide de la sub-stance abrasée, la concentricité de l’instrument White-TIGER reste optimale et exempte de vibrations (état lisse de la sur-face abrasée).
höchste standzeit (3)
Durch das patentierte LLD-Bonding können die Diamantkörner nicht mehr herausgelöst werden. Dadurch erhöht sich die Standzeit der White-TIGER Diamantinstrumente um ein Mehrfaches. Bei Standard-Diamant-instru-menten lösen sich die Diamantkörner früh-zeitig aus der Bindung, was nur eine kurze Standzeit der Instrumente ergibt.
Anwendung
In der Keramik-/ Zirkonoxid Vollkeramik-BearbeitungKeramik- und Kunststoff-VerblendtechnikFeinbearbeitung von Vollkeramik undKompositenOkklusale Adjustierung auf Zirkonoxid -VollkeramikAufpassen von gesinterten Zirkonoxidge-rüsten und KronenAbtragen von Druckstellen an ZirkonoxidMaterialienOkklusales Konturieren und Fissuren-gestaltung
AnwendungshinwiseDas Beschleifen der Keramik-/ ZirkonoxidVollkeramik erfolgt unter Wasserkühlung mit der Laborturbine.nur mit leichtem Arbeitsdruck arbeiten Dre-zahlangaben einhalten.
Maximum life-span (3)
The LLD bond ensures that diamond particles no longer come loose. This increases the life span of the White-TIGER diamond instru-ments several times over. Using standard diamond instruments the diamond particles come loose much sooner from the bond resul-ting in a short life span of the instruments.
Application
Preparing porcelain/ zirconia all-porcelainPorcelain and composite facingsFine contouring of all-porcelain and compo-sitesOcclusal adjustments on zirconia all-porcelainFitting sintered zirconia frameworks and crownsRemoving high spots on zirconia restorationsContouring occlusal surfaces and preparing fissures
Instructions for usePorcelain / zirconia all-porcelain should be prepared with a laboratory turbine using water coolant.Use only minimum pressure when preparing and adhere to the recommended rpm.
extraordinaire durabilité (3)
Du fait de la liaison LLD brevetée, les particules de diamant ne peuvent plus se décoller. La durabilité des instruments White-TIGER est ainsi très fortement augmentée. Avec les instruments standards, les particules de diamant se détachent prématurément du liant ce qui a pour conséquence une faible durée de vie de ces instruments.
utilisationTraitement de la céramique / tout-céramique en oxyde de zirconiumTechnique de recouvrement avec de la céra-mique et de la résineTraitement précis du tout-céramique et des compositesAjustage occlusal du tout-céramique en oxyde de zirconiumAjustement d´armatures en oxyde de zirconi-um fritté et de couronnesElimination de points de pression sur les matériaux en oxyde de zirconiumContour occlusal et réalisation de fissures
recommandation pour l’utilisationLe fraisage de la céramique/tout-céramique en oxyde de zirconium se réalise sous irrigati-on d´eau avec une turbine de laboratoire.Travailler seulement avec une légère pression, respecter le nombre de tours.
conventionaldiamonds
WhiteTIger
cutting life
cutti
ng e
ffici
ency
llD - Bonding
Multilayer - Bonding
1 2 3
86
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
Die natur-Diamanten der White-TIGER Dia-mantinstru mente sind durch ein patentiertes LLD – Herstellungsverfahren mehrschich-tig und dauerhaft auf dem rostfreien Schaft gebunden.
Die hohe Qualität dieser Diamant-Instru-mente bietet dem Anwender viele Vorteile gegenüber dem Arbeiten mit Standard - Dia-mantinstrumenten und führt zu optimalsten Ergebnissen.
hohe schleifleistung (1)
Durch das patentierte LLD - Bonding sowie die mehrschichtige Diamantierung ergibt sich ein schnellerer Abtransport der Schleifsub-stanz (hohe Schleifleistung) und damit auch ein kühles Schleifen.
glattes schliffbild (2)
Durch den raschen Abtransport der Schleif-substanz wird ein optimaler, vibrationsfrei-er Rundlauf der White-TIGER Instrumente erreicht (glattes Schliffbild).
The natural diamonds of the White-TIGER diamond instruments are multi-layered and permanently bonded to the stainless steel shank using a patented LLD manufacturing process.
The high quality of these diamond instru-ments offers the user many advantages compared to working with standard diamond instruments and leads to optimal results.
high cutting performance (1)
With the patented LLD bond and multi-layered diamond veneer, the tooth structure is reduced faster (high cutting performance), thus ensuring minimum heat generation when cutting.
smooth cut (2)
Conveying the debris away from the surface rapidly enables White-TIGER instruments to rotate concentrically and vibration-free (smooth cut).
Les particules de diamant naturel des instru-ments White-TIGER sont liées durable-ment et par couches multiples à la tige en acier inoxydable au moyen du procédé de fabrication breveté LLD. La grande quali-té de ces instruments diamantés permet à l’utilisateur de bénéficier de nombreux avan-tages par rapport au travail entrepris à l’aide d’instruments diamantés standards et condu-it à obtenir les résultats les plus optimaux.
fort pouvoir abrasif (1)
Le procédé de liaison breveté LLD ainsi que la diamantation multicouches ont pour effet une évacuation très rapide de la substance abrasée (fort pouvoir abrasif) et par consé-quent, un meulage s’effectuant à une tempé-rature plus basse.
etat lisse, surface abrasée (2)
Du fait de l’évacuation rapide de la sub-stance abrasée, la concentricité de l’instrument White-TIGER reste optimale et exempte de vibrations (état lisse de la sur-face abrasée).
höchste standzeit (3)
Durch das patentierte LLD-Bonding können die Diamantkörner nicht mehr herausgelöst werden. Dadurch erhöht sich die Standzeit der White-TIGER Diamantinstrumente um ein Mehrfaches. Bei Standard-Diamant-instru-menten lösen sich die Diamantkörner früh-zeitig aus der Bindung, was nur eine kurze Standzeit der Instrumente ergibt.
Anwendung
In der Keramik-/ Zirkonoxid Vollkeramik-BearbeitungKeramik- und Kunststoff-VerblendtechnikFeinbearbeitung von Vollkeramik undKompositenOkklusale Adjustierung auf Zirkonoxid -VollkeramikAufpassen von gesinterten Zirkonoxidge-rüsten und KronenAbtragen von Druckstellen an ZirkonoxidMaterialienOkklusales Konturieren und Fissuren-gestaltung
AnwendungshinwiseDas Beschleifen der Keramik-/ ZirkonoxidVollkeramik erfolgt unter Wasserkühlung mit der Laborturbine.nur mit leichtem Arbeitsdruck arbeiten Dre-zahlangaben einhalten.
Maximum life-span (3)
The LLD bond ensures that diamond particles no longer come loose. This increases the life span of the White-TIGER diamond instru-ments several times over. Using standard diamond instruments the diamond particles come loose much sooner from the bond resul-ting in a short life span of the instruments.
Application
Preparing porcelain/ zirconia all-porcelainPorcelain and composite facingsFine contouring of all-porcelain and compo-sitesOcclusal adjustments on zirconia all-porcelainFitting sintered zirconia frameworks and crownsRemoving high spots on zirconia restorationsContouring occlusal surfaces and preparing fissures
Instructions for usePorcelain / zirconia all-porcelain should be prepared with a laboratory turbine using water coolant.Use only minimum pressure when preparing and adhere to the recommended rpm.
extraordinaire durabilité (3)
Du fait de la liaison LLD brevetée, les particules de diamant ne peuvent plus se décoller. La durabilité des instruments White-TIGER est ainsi très fortement augmentée. Avec les instruments standards, les particules de diamant se détachent prématurément du liant ce qui a pour conséquence une faible durée de vie de ces instruments.
utilisationTraitement de la céramique / tout-céramique en oxyde de zirconiumTechnique de recouvrement avec de la céra-mique et de la résineTraitement précis du tout-céramique et des compositesAjustage occlusal du tout-céramique en oxyde de zirconiumAjustement d´armatures en oxyde de zirconi-um fritté et de couronnesElimination de points de pression sur les matériaux en oxyde de zirconiumContour occlusal et réalisation de fissures
recommandation pour l’utilisationLe fraisage de la céramique/tout-céramique en oxyde de zirconium se réalise sous irrigati-on d´eau avec une turbine de laboratoire.Travailler seulement avec une légère pression, respecter le nombre de tours.
conventionaldiamonds
WhiteTIger
cutting life
cutti
ng e
ffici
ency
llD - Bonding
Multilayer - Bonding
1 2 3
White Tiger Diamonds
VARIOstar K50/D50 BRUSHLESS HANDPIECE
Rotation speed indicator
Easy to read and continuous
Speed knob
To set desired max speed
Direction switch
To select forward/reverse
Digital speed display
Easy to read
Tool tray
Knee Control
Safety switch
Unlock the max rotation speed
Right hand rotation (+)
Button to increase the max rotation speed
Left hand rotation (–)
Button to reduce the max rotation speed
Speed control
86
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
Die natur-Diamanten der White-TIGER Dia-mantinstru mente sind durch ein patentiertes LLD – Herstellungsverfahren mehrschich-tig und dauerhaft auf dem rostfreien Schaft gebunden.
Die hohe Qualität dieser Diamant-Instru-mente bietet dem Anwender viele Vorteile gegenüber dem Arbeiten mit Standard - Dia-mantinstrumenten und führt zu optimalsten Ergebnissen.
hohe schleifleistung (1)
Durch das patentierte LLD - Bonding sowie die mehrschichtige Diamantierung ergibt sich ein schnellerer Abtransport der Schleifsub-stanz (hohe Schleifleistung) und damit auch ein kühles Schleifen.
glattes schliffbild (2)
Durch den raschen Abtransport der Schleif-substanz wird ein optimaler, vibrationsfrei-er Rundlauf der White-TIGER Instrumente erreicht (glattes Schliffbild).
The natural diamonds of the White-TIGER diamond instruments are multi-layered and permanently bonded to the stainless steel shank using a patented LLD manufacturing process.
The high quality of these diamond instru-ments offers the user many advantages compared to working with standard diamond instruments and leads to optimal results.
high cutting performance (1)
With the patented LLD bond and multi-layered diamond veneer, the tooth structure is reduced faster (high cutting performance), thus ensuring minimum heat generation when cutting.
smooth cut (2)
Conveying the debris away from the surface rapidly enables White-TIGER instruments to rotate concentrically and vibration-free (smooth cut).
Les particules de diamant naturel des instru-ments White-TIGER sont liées durable-ment et par couches multiples à la tige en acier inoxydable au moyen du procédé de fabrication breveté LLD. La grande quali-té de ces instruments diamantés permet à l’utilisateur de bénéficier de nombreux avan-tages par rapport au travail entrepris à l’aide d’instruments diamantés standards et condu-it à obtenir les résultats les plus optimaux.
fort pouvoir abrasif (1)
Le procédé de liaison breveté LLD ainsi que la diamantation multicouches ont pour effet une évacuation très rapide de la substance abrasée (fort pouvoir abrasif) et par consé-quent, un meulage s’effectuant à une tempé-rature plus basse.
etat lisse, surface abrasée (2)
Du fait de l’évacuation rapide de la sub-stance abrasée, la concentricité de l’instrument White-TIGER reste optimale et exempte de vibrations (état lisse de la sur-face abrasée).
höchste standzeit (3)
Durch das patentierte LLD-Bonding können die Diamantkörner nicht mehr herausgelöst werden. Dadurch erhöht sich die Standzeit der White-TIGER Diamantinstrumente um ein Mehrfaches. Bei Standard-Diamant-instru-menten lösen sich die Diamantkörner früh-zeitig aus der Bindung, was nur eine kurze Standzeit der Instrumente ergibt.
Anwendung
In der Keramik-/ Zirkonoxid Vollkeramik-BearbeitungKeramik- und Kunststoff-VerblendtechnikFeinbearbeitung von Vollkeramik undKompositenOkklusale Adjustierung auf Zirkonoxid -VollkeramikAufpassen von gesinterten Zirkonoxidge-rüsten und KronenAbtragen von Druckstellen an ZirkonoxidMaterialienOkklusales Konturieren und Fissuren-gestaltung
AnwendungshinwiseDas Beschleifen der Keramik-/ ZirkonoxidVollkeramik erfolgt unter Wasserkühlung mit der Laborturbine.nur mit leichtem Arbeitsdruck arbeiten Dre-zahlangaben einhalten.
Maximum life-span (3)
The LLD bond ensures that diamond particles no longer come loose. This increases the life span of the White-TIGER diamond instru-ments several times over. Using standard diamond instruments the diamond particles come loose much sooner from the bond resul-ting in a short life span of the instruments.
Application
Preparing porcelain/ zirconia all-porcelainPorcelain and composite facingsFine contouring of all-porcelain and compo-sitesOcclusal adjustments on zirconia all-porcelainFitting sintered zirconia frameworks and crownsRemoving high spots on zirconia restorationsContouring occlusal surfaces and preparing fissures
Instructions for usePorcelain / zirconia all-porcelain should be prepared with a laboratory turbine using water coolant.Use only minimum pressure when preparing and adhere to the recommended rpm.
extraordinaire durabilité (3)
Du fait de la liaison LLD brevetée, les particules de diamant ne peuvent plus se décoller. La durabilité des instruments White-TIGER est ainsi très fortement augmentée. Avec les instruments standards, les particules de diamant se détachent prématurément du liant ce qui a pour conséquence une faible durée de vie de ces instruments.
utilisationTraitement de la céramique / tout-céramique en oxyde de zirconiumTechnique de recouvrement avec de la céra-mique et de la résineTraitement précis du tout-céramique et des compositesAjustage occlusal du tout-céramique en oxyde de zirconiumAjustement d´armatures en oxyde de zirconi-um fritté et de couronnesElimination de points de pression sur les matériaux en oxyde de zirconiumContour occlusal et réalisation de fissures
recommandation pour l’utilisationLe fraisage de la céramique/tout-céramique en oxyde de zirconium se réalise sous irrigati-on d´eau avec une turbine de laboratoire.Travailler seulement avec une légère pression, respecter le nombre de tours.
conventionaldiamonds
WhiteTIger
cutting lifecu
tting
effi
cien
cy
llD - Bonding
Multilayer - Bonding
1 2 3
CALL US ON
01494 448474
FOR PRICES
Foot Control £740.75SZU040
£729.50SZU039
29 87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W368Pointed Bud
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W369Egg Shape/Football
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W830LPear Long
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W801Round
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W846KRRound Edge Taper
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W878KTorpedo Tapered
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W881Round End Cylinder
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W879KTorpedo Tapered
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
W863Flame
↻opt. 160.000 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
White Tiger Diamonds
L mm 5,5
Size 1/10 mm 020
Order No. SET1222
Shank
L mm
Size 1/10 mm 014 021 023
Order No. SET1229 SET1230 SET1231
Shank: FG
L mm 6,0 6,0
Size 1/10 mm 016 023
Order No. SET1244 SET1245
Shank: FG
L mm 8,0
Size 1/10 mm 014
Order No. SET1279
Shank: FG
L mm 8,0 8,0 8,0 8,0 8,0
Size 1/10 mm 014 016 018 020 022
Order No. SET1252SET1253SET1254SET1255SET1256
Shank: FG
L mm 10,0 10,0 10,0 10,0
Size 1/10 mm 012 014 016 018
Order No. SET1267SET1268SET1269SET1270
Shank: FG
L mm 10,0 10,0
Size 1/10 mm 012 016
Order No. SET1246 SET1247
Shank: FG
L mm 4,0 5,0 5,0
Size 1/10 mm 012 014 016
Order No. SET1238 SET1239 SET1240
Shank: FG
L mm 4,2
Size 1/10 mm 023
Order No. SET1226
Shank: FG
For laboratory turbine with water cooling• Blue Ring Standard - 126µm ISO No. 524• Red Ring Fine - 40µm ISO No. 514• Green Ring Coarse - 151µm ISO No. 534
30
90
suPerflexIn superfeiner, feiner und standard Diamant-körnung, zum Fein- sowie Vorseparieren und Konturieren von Keramik.
In superfine, fine and standard diamond grit, for fine and pre-separating and contouring of ceramics.
En grain diamanté extra fin, fin et standard, pour la pré-séparation, séparation fine et le contourage des céramiques.
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
ulTrAflexEine ultradünne Diamantscheibe mit extrafei-ner Diamantkörnung zum Separieren und Kon-turieren von Keramik- und Kunststoffverblen-dungen im Front- und Seitenzahnbereich.
An ultrathin Diamond Disc with extrafine dia-mond grit for separation and contouring of por-celain and composite veneers on anterior and posterior teeth.
Un disque diamanté ultra mince avec des grains diamantés extra-fin, pour séparer et contourer les incrustations cosmétiques réa-lisées en céramique ou en résine, au niveau des blocs antérieurs et postérieurs.
cAD/cAM zrO2 restorationDiamantscheibe zum Heraustrennen von Kro-nen- und Brücken aus HiP-ZrO2-Gerüsten.
Diamond disc for separating crowns and bridges from HiP ZrO2 framework.
Disque diamanté pour sectionner les jonc-tions retenant les couronnes et les bridges aux armatures en HiP ZrO2.
suPerflexIn feiner und standard Diamantkörnung, fein zum Separieren und Konturieren, standard zum Vorschleifen, Vortrennen und Konturieren von Keramik.
In fine and standard diamond grit, fine for separating and contouring, standard for pre-cutting,separating and contouring of ceramics.
En grain diamanté fin pour séparer et contou-rer, standard pour dégrossir, pré-séparer et contourer les céramiques.
366
p 1
L mm 0,09Size 1/10 mm 220Order No. ● 366.504.220HPISO No. 806 104... 366 504 220
dmax. 20.000
L
L
L mm 0,09Size 1/10 mm 220Order No. ● 367.504.220HPISO No. 806 104... 367 504 220
dmax 20.000
367
p 1
L
L
317
p 1
L mm 0,15 0,25Size 1/10 mm 220 220Order No. ● 317.514.220HP ● 317.524.220HPISO No. 806 104... 317 514 220 317 524 220
dmax. 20.000 20.000
L
L
350
p 1
L mm 0,15 0,25 0,15 0,25Size 1/10 mm 190 190 220 220Order No. ● 350.514.190HP ● 350.524.190HP ● 350.514.220HP ● 350.524.220HPISO No. 806 104... 350 514 190 350 524 190 350 514 220 350 524 220
dmax. 20.000 20.000 15.000 15.000
L
L
351
p 1
L mm 0,10 0,15Size 1/10 mm 220 220Order No. ● 351.514.220HP ● 351.524.220HPISO No. 806 104... 351 514 220 351 524 220
dmax. 15.000 15.000
L
L
353
p 1
L mm 0,12 0,15 0,25Size 1/10 mm 220 220 220Order No. ● 353.504.220HP ● 353.514.220HP ● 353.524.220HPISO No. 806 104... 353 504 220 353 514 220 353 524 220
dmax. 15.000 15.000 15.000
L
L
327
p 1
L mm 0,13 0,13Size 1/10 mm 80 100Order No. ● 327.514.080HP ● 327.514.100HPISO No. 806 104... 327 514 080 327 514 100
dopt. 20.000 20.000
L mm 0.09
Size 1/10 mm • 220
Order No. SET639
↻max. 20,000
L mm 0,15 0,25
Size 1/10 mm • 220 • 220
Order No. SET690 SET691
↻max. 20,000 20,000
L mm 0,15 0,25 0,15 0,25
Size 1/10 mm • 190 • 190 • 220 • 220
Order No. SET651 SET653 SET652 SET654
↻max. 20,000 20,000 15,000 15,000
L mm 0,10 0,15
Size 1/10 mm • 220 • 220
Order No. SET656 SET657
↻max. 15,000 15,000
L mm 0,12 0,15 0,25
Size 1/10 mm • 220 • 220 • 220
Order No. SET660 SET661 SET662
↻max. 15,000 15,000 15,000
366
317
350
353
351
367ULTRAFLEX
SUPERFLEX
SUPERFLEX
Diamond Discs
L mm 0.09
Size 1/10 mm • 220
Order No. SET640
↻max. 20,000
Email us today sales@skillbond.com
CALL US ON
01494 448474
FOR PRICES
31 91
358
p 1
L
356
p 1
L
355
p 1
L
355
p 1
L
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
L mm 0,12 0,12Size 1/10 mm 190 220Order No. ● 355.504.190HP ● 355.504.220HPISO No. 806 104... 355 504 190 355 504 220
dmax. 20.000 15.000
suPerflexIn superfeiner, feiner und stan-dard Diamantkörnung, superfein zum feinst Separieren, fein und standard zum Vorseparieren und groben Vortrennen von Keramik.
In superfine, fine and standard diamond grit. Superfine for very finely separating, fine and stan-dard for initially separating and contouring porcelain.
En grain diamanté très fin, fin et standard, en très fin pour sépa-rer précisément, en fin et stan-dard pour pré-séparer et dégros-sir les céramiques.
L mm 0,15 0,15 0,15 0,25 0,25Size 1/10 mm 160 190 220 190 220Order No. ● 355.514.160HP ● 355.514.190HP ● 355.514.220HP ● 355.524.190HP ● 355.524.220HPISO No. 806 104... 355 514 160 355 514 190 355 514 220 355 524 190 355 524 220
dmax. 20.000 20.000 15.000 20.000 15.000
L
L
L mm 0,10 0,10Size 1/10 mm 190 220Order No. ● 356.514.190HP ● 356.514.220HPISO No. 806 104... 356 514 190 356 514 220
dmax. 20.000 15.000
L
357
p 1
L
L mm 0,10 0,10Size 1/10 mm 190 220Order No. ● 357.514.190HP ● 357.514.220HPISO No. 806 104... 357 514 190 357 514 220
dmax 20.000 15.000
L
L mm 0,15 0,25 0,15 0,25Size 1/10 mm 190 190 220 220Order No. ● 358.514.190HP ● 358.524.190HP ● 358.514.220HP ● 358.524.220HPISO No. 806 104... 358 514 190 358 524 190 358 514 220 358 524 220
dmax. 20.000 20.000 15.000 15.000
suPerflexIn feiner und standard Diamant-körnung, zum Vorseparieren und Konturieren von Keramik.
In fine and standard diamond grit for pre-separating and contouring of ceramics.
En grain diamanté fin et stan-dard, pour la pre-séparation et le contourage des céramiques.
L
363
p 1
L
L mm 0,10Size 1/10 mm 100Order No. ● 363.514.100HPISO No. 806 104... 363 514 100
dmax. 20.000
L
361
p 1
L
L mm 0,15 0,15Size 1/10 mm 080 100Order No. ● 361.514.080HP ● 361.514.100HPISO No. 806 104... 361 514 080 361 514 100
dmax. 20.000 20.000
L
suPerflexIn feiner Diamantkörnung, zum Abrunden von Approximalflä-chen, zum Separieren von Kera-mik.
In fine diamond grit, to rounden off proximal areas, for separating of ceramics.
En grain diamanté fin, pour arrondir les faces proximales, pour séparer les céramiques.
355.524.220hP
355
355
356
358
361 363
357
•
SUPERFLEX
SUPERFLEX
SUPERFLEX
Diamond Discs
L mm 0,12 0,12
Size 1/10 mm • 190 • 220
Order No. SET663 SET664
↻max. 20,000 15,000
L mm 0,15 0,15 0,15 0,25 0,25
Size 1/10 mm • 160 • 190 • 220 • 190 • 220
Order No. SET665 SET666 SET667 SET668 SET669
↻max. 20,000 15,000 15,000 20,000 15,000
L mm 0,10 0,10
Size 1/10 mm • 190 • 220
Order No. SET670 SET671
↻max. 20,000 15,000
L mm 0,15 0,25 0,15 0,25
Size 1/10 mm • 190 • 190 • 220 • 220
Order No. SET677 SET679 SET678 SET680
↻max. 20,000 20,000 15,000 15,000
L mm 0,15 0,15
Size 1/10 mm • 080 • 100
Order No. SET681 SET682
↻max. 20,000 20,000
L mm 0,10
Size 1/10 mm • 100
Order No. SET683
↻max. 20,000
L mm 0,10 0,10
Size 1/10 mm • 190 • 220
Order No. SET673 SET674
↻max. 20,000 15,000
3292
605
p 1
L
405
p 1
L
396
p 1
L
393
p 1
L
L mm 0,15Size 1/10 mm 220Order No. ● 393.514.220HPISO No. 806 104... 393 514 220
dmax. 15.000
suPerflexScheibe mit ovaler Perforation in feiner Diamantkör-nung, zum Separieren und Konturieren von Keramik. Vorteile: weiches Arbeiten bei hohem Materialabtrag, hohe Flexibilität, gute Durchsicht
Disc with oval shaped perforations with fine diamond grit, for the separation and contouring of ceramics. Advantages: soft work at high levels of material remo-val, high flexibility, provides good visibility
Disque en grain diamanté fin, avec perforation ovale, pour séparer et contourer les céramiques. Avantages: travail agréable, fort pouvoir abrasif, gran-de flexibilité, bonne visibilité
L mm 0,15Size 1/10 mm 220Order No. ● 396.514.220HPISO No. 806 104... 396 514 220
dmax. 15.000
suPerflexScheibe mit Bogenperforation in feiner Diamantkör-nung, zum feinen Separieren und Konturieren von Keramik. Vorteile: hohe Abtragsleistung, hohe Flexibi-lität, gute Durchsicht, vermeidet Schleiffacetten
Disc with arch-shaped perforations with fine diamond grit, for separation and contouring of ceramics. Advantages: high removal capacity, high flexibility, provides good visibility, avoids grinding-facets
Disque avec perforation arqué en grain diamanté fin, pour séparer et contourer les céramiques. Avantages: fort pouvoir abrasif, grande flexibilité, bonne visibilité, évite des traces de meulage
L mm 0,15 0,25Size 1/10 mm 220 220Order No. ● 405.514.220HP ● 405.524.220HPISO No. 806 104... 405 514 220 405 524 220
dmax. 15.000 15.000
suPerflexIn feiner Diamantkörnung zum feinsten Separieren von Keramik.
In fine diamond grit for finest separation of ceramics.
En grain diamanté fin pour une séparation ultra fine et précise des céramiques.
DIAMANT-NeTzscheIBeZum Separieren und Konturieren von Keramik, Kunst-stoff und Modellgips. Flexibel, mit optimaler Durch-sicht, hohem Materialabtrag und guter Spanabfuhr.
DIAMOND OPeN-MesheD DIscFor separating and contouring of ceramics, acrylics and plaster. Flexible, with excellent vision, highest material reduction and smooth grinding performance.
DIsQue DIAMANTé perforéConçu pour séparer et contourer la céramique, les acryliques et les plâtres. Flexible, avec une excellente visibilité sur le champ de travail, fort pouvoir abrasif, dégagement efficace des matériaux.
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
L
L
L
L mm 0,15 0,25Size 1/10 mm 220 220Order No. ● 605.514.220HP ● 605.524.220HPISO No. 806 104... 605 514 220 605 524 220
dmax. 15.000 15.000
suPerflexPerforierte Diamantscheibe in feiner und standard Diamantkörnung, zum feinen und groben Separieren und Konturieren von Keramik mit guter Durchsicht.
Perforated Diamond Disc with fine and standard diamond grit, for fine and coarse separation and contouring of ceramics.
Disque perforé en grain diamanté fin et standard, pour la séparation fine et grossière et le contourage des céramiques, bonne visibilité.
L
400
p 1
L
L mm 0,15 0,15Size 1/10 mm 220 190Order No. ● 400.514.220HP ● 400.514.190HPISO No. 806 104... 400 514 220 400 514 190
dmax. 15.000 20.000
L
393
396
400
405
605
SUPERFLEX
SUPERFLEX
SUPERFLEX
SUPERFLEX
DIAMOND OPEN-MESHED DISC
Diamond Discs
L mm 0,15
Size 1/10 mm • 220
Order No. SET692
↻max. 15,000
L mm 0,15
Size 1/10 mm • 220
Order No. SET693
↻max. 15,000
L mm 0,15
Size 1/10 mm • 220
Order No. SET650
↻max. 15,000
L mm 0,15 0,25
Size 1/10 mm • 220 • 220
Order No. SET684 SET685
↻max. 15,000 15,000
L mm 0,15 0,25
Size 1/10 mm • 220 • 220
Order No. SET686 SET687
↻max. 15,000 15,000
33 93
365
p 1
L
705
p 1
L
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
L mm 0,15 0,15Size 1/10 mm 190 220Order No. ● 705.514.190HP ● 705.514.220HPISO No. 806 104... 705 514 190 705 514 220
dmax 20.000 15.000
suPerflexGezahnte Diamantscheibe in feiner Dia-mantkörnung, zum Separieren von Keramik, Gips, Kunststoffe, extraharte Verblend-kunststoffe, Trennen von Kunststoffen.
Serrated Diamond Disc with fine diamond grit, for separating ceramics, plaster, acry-lics, resin veneers.
Disque cranté en grain diamanté fin, pour séparer les céramiques, le plâtre, les acryli-ques et les résines pour incrustations.
L
321
p 1
L
L mm 0,20 0,30 0,20 0,30Size 1/10 mm 190 190 220 220Order No. ● 321.514.190HP ● 321.524.190HP ● 321.514.220HP ● 321.524.220HPISO No. 806 104... 321 514 190 321 524 190 321 514 220 321 524 220
dmax. 20.000 20.000 15.000 15.000
flexIn feiner und standard Diamantkörnung, zum Vorseparieren und Konturieren von Keramik.
In fine and standard diamond grit for pre-separating and contouring of ceramics.
En grain diamanté fin et standard, pour la pre-séparation et le contourage des céra-miques.
L
335
p 1
L
L mm 0,30Size 1/10 mm 220Order No. ● 335.524.220HPISO No. 806 104... 335 524 220
dmax. 15.000
flexPerforierte Diamantscheibe in standard Diamantkörnung, zum groben Vorschleifen, Vortrennen und Konturieren von Keramik.
Perforated Diamond Disc in standard dia-mond grit for rough pre-cutting, separating and contouring of ceramics.
Disque perforé en grain diamanté standard, pour le dégrossissage, la séparation et le contourage des céramiques.
L
345
p 1
L
L mm 0,20 0,20 0,30Size 1/10 mm 190 220 220Order No. ● 345.514.190HP ● 345.514.220HP ● 345.524.220HPISO No. 806 104... 345 514 190 345 514 220 345 524 220
dmax. 20.000 15.000 15.000
flexIn feiner und standard Diamantkörnung, zum Trennen und Konturieren von Keramik.
In fine and standard diamond grit for sepa-rating and contouring of ceramics.
En grain diamanté fin et standard, pour séparer et contourer les céramiques.
L
flexDiamantscheibe für schnelles Gips-Tren-nen. Die spezielle Segmentierung der Scheibe transportiert den Schleifstaub ab, so dass keine Verkantung erfolgen kann.
Diamond Disc for a quick and smooth plaster sectioning. The special serrated edges increase the evacuation of the plaster dust to avoid any clogging.
Disque diamanté conçu pour séparer le plâtre. Le disque cranté permet une coupe plus rapide et guidée. Grâce à la ségmen-tation du disque, l’évacuation des pous-sières est plus efficace et empèche ainsi un bloquage du disque.
L mm 0,35 0,35Size 1/10 mm 300 450Order No. ● 365.524.300HP ● 365.524.450HPISO No. 806 104... 365 524 300 365 524 450
dmax. 10.000 10.000
L
↶↶↶↶705
321
335
345
365
SUPERFLEX
FLEX
FLEX
FLEX
FLEX
Diamond Discs
L mm 0,15 0,15
Size 1/10 mm • 190 • 220
Order No. SET688 SET689
↻max. 20,000 15,000
L mm 0,30
Size 1/10 mm • 220
Order No. SET700
↻max. 15,000
L mm 0,20 0,20 0,30
Size 1/10 mm • 190 • 220 • 220
Order No. SET701 SET702 SET703
↻max. 20,000 15,000 15,000
L mm 0,35 0,35
Size 1/10 mm • 300 • 450
Order No. SET705 SET706
↻max. 10,000 10,000
L mm 0,20 0,30 0,20 0,30
Size 1/10 mm • 190 • 190 • 220 • 220
Order No. SET688 SET689 SET696 SET698
↻max. 20,000 20,000 15,000 15,000
34
94
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
suPerflex TurBOIn superfeiner und feiner Diamantkörnung für Keramik, Composites, Kunststoffe, die Spirale ermöglicht einen schnellen, optimalen Abtrans-port des Schleifgutes, zum Konturieren, zum Trennen von Zahnkränzen an Sägemodellen.
In superfine and fine diamond grit for ceramics, composites and acrylics. The spiral cut enables effortless permanent removal of residue for con-touring and separating of saw-cut models.
En grain diamanté fin et extra fin pour céra-miques, composites et acryliques. La spirale permet un dégagement efficace des copeaux d’usinages, pour séparer et contourer des modèles de scie.
Trennscheibe 378mit beidseitiger Diamant-Vollbelegung zum Separieren und Trennen von Press-Muffeln. Eine spezielle Segmentierung verhindert ein Verklem-men oder Einhaken der Scheibe.
cut-off disc 378coated on both sides for separating and cutting off press moulds. Provided with segmentation wich preventing jamming or catching of the disc.
Disque à tronçonner 378entiere ment diamantés sur les deux faces pour séparer et sectionnner les moules de pressage. Avec une segmentation pour d‘éviter ainsi un blocage ou un accrochage du disque.
flex TurBOIn standard Diamantkörnung, die Spirale ermög-licht einen schnellen und optimalen Abtransport des Schleifgutes, zum Separieren von Kunststoff und Keramik, kein Verschmieren.
In standard diamond grit, the spiral cut enables a quick and optimum removal of residue for sepa-rating of acrylics and ceramics, no smearing.
En grain diamanté standard, la spirale assure un dégagement efficace des copeaux d’usinages, pour la séparation des acryliques et des céra-miques, ne colore pas la matière.
505
p 1
L
L mm 0,12 0,12 0,12Size 1/10 mm 160 190 220Order No. ● 505.504.160HP ● 505.504.190HP ● 505.504.220HPISO No. 806 104... 505 504 160 505 504 190 505 504 220
dmax. 20.000 20.000 20.000
L
505
p 1
L
L
L mm 0,15 0,15Size 1/10 mm 190 220Order No. ● 505.514.190HP ● 505.514.220HPISO No. 806 104... 505 514 190 505 514 220
dmax. 20.000 20.000
362
p 1
L
L mm 0,30 0,30Size 1/10 mm 080 100Order No. ● 362.524.080HP ● 362.524.100HPISO No. 806 104... 362 524 080 362 524 100
dmax. 25.000 25.000
L
378
p 1
L mm 0,35Size 1/10 mm 450Order No. ● 378.524.450HPISO No. 806 104... 378 524 450
dmax. 10.000
L
↶↶
FLEX TURBO362
94
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
suPerflex TurBOIn superfeiner und feiner Diamantkörnung für Keramik, Composites, Kunststoffe, die Spirale ermöglicht einen schnellen, optimalen Abtrans-port des Schleifgutes, zum Konturieren, zum Trennen von Zahnkränzen an Sägemodellen.
In superfine and fine diamond grit for ceramics, composites and acrylics. The spiral cut enables effortless permanent removal of residue for con-touring and separating of saw-cut models.
En grain diamanté fin et extra fin pour céra-miques, composites et acryliques. La spirale permet un dégagement efficace des copeaux d’usinages, pour séparer et contourer des modèles de scie.
Trennscheibe 378mit beidseitiger Diamant-Vollbelegung zum Separieren und Trennen von Press-Muffeln. Eine spezielle Segmentierung verhindert ein Verklem-men oder Einhaken der Scheibe.
cut-off disc 378coated on both sides for separating and cutting off press moulds. Provided with segmentation wich preventing jamming or catching of the disc.
Disque à tronçonner 378entiere ment diamantés sur les deux faces pour séparer et sectionnner les moules de pressage. Avec une segmentation pour d‘éviter ainsi un blocage ou un accrochage du disque.
flex TurBOIn standard Diamantkörnung, die Spirale ermög-licht einen schnellen und optimalen Abtransport des Schleifgutes, zum Separieren von Kunststoff und Keramik, kein Verschmieren.
In standard diamond grit, the spiral cut enables a quick and optimum removal of residue for sepa-rating of acrylics and ceramics, no smearing.
En grain diamanté standard, la spirale assure un dégagement efficace des copeaux d’usinages, pour la séparation des acryliques et des céra-miques, ne colore pas la matière.
505
p 1
L
L mm 0,12 0,12 0,12Size 1/10 mm 160 190 220Order No. ● 505.504.160HP ● 505.504.190HP ● 505.504.220HPISO No. 806 104... 505 504 160 505 504 190 505 504 220
dmax. 20.000 20.000 20.000
L
505
p 1
L
L
L mm 0,15 0,15Size 1/10 mm 190 220Order No. ● 505.514.190HP ● 505.514.220HPISO No. 806 104... 505 514 190 505 514 220
dmax. 20.000 20.000
362
p 1
L
L mm 0,30 0,30Size 1/10 mm 080 100Order No. ● 362.524.080HP ● 362.524.100HPISO No. 806 104... 362 524 080 362 524 100
dmax. 25.000 25.000
L
378
p 1
L mm 0,35Size 1/10 mm 450Order No. ● 378.524.450HPISO No. 806 104... 378 524 450
dmax. 10.000
L
↶↶
505
505
SUPERFLEX TURBO
95
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
DiamantscheibenDiamond DiscsDisques Diamants
opt. d
≤ 180 dopt. 25 000 min-1
≥ 180 dopt. 20 000 min-1
≥ 220 dopt. 15 000 min-1
≥ 300 dopt. 10 000 min-1
MulticutUniversal Diamantscheibe mit mehrschich-tiger, galvanisch durchsetzter Randdia-mantierung für hohe Standzeit und höchste Schnittleistung.
Hergestellt durch Galvanoforming (Galvano-plastik / Elektroforming) bietet die MultiCut Diamantscheibe einzigartige Eigenschaften.
Die mehrschichtige, galvanisch durchsetzte Randdiamantierung garantiert ein Schleifver-halten, ähnlich einer Sinterdiamantscheibe, aber flexibel.
MulticutUniversal diamond disc with a multilayered, electroformed diamond coating on the rim for a long service life and maximum cutting capacity.
The MultiCut diamond disc, manufactured by electroforming, has unique properties.
The multilayered, electroformed diamond coating on the rim ensures a cutting perfor-mance similar to that of a sintered diamond disc, but with a higher degree of flexibility.
MulticutDisque diamanté universel avec un grain dia-manté marginal en plusieurs couches, infilt-ré par galvano pour une grande longévité et une capacité de coupe la plus élevée.
Fabriqué par galvanoforming (galvano-plastie/electroforming), le disque diamanté MultiCut offre des propriétés exceptionnelles.
Le grain diamanté marginal en plusieurs couches et infiltré par galvano garantit une coupe similaire à un disque diamanté par frit-tage, tout en étant souple.
eigenschaftenIm Vergleich mit einer Standart Diamant-scheibe zeichnet sich die MultiCut Universal-scheibe dadurch aus, dass die Randdiaman-tierung durch und durch mit naturdiamanten belegt ist.
Eine Spezialbindung garantiert optimale Schleifergebnisse.
• Mehrschichtige Diamantierung für Kanten und Flächenschliff
• Hohe Abtrag- und Schnittleistung
• Arbeiten ohne Streifenbildung
• Flexible, hohe Scheiben-Stabilität
• Hohe Standzeit
PropertiesUnlike standard diamond discs, the MultiCut universal disc features a diamond-coated rim completely impregnated with natural dia-monds.
Special bonding ensures optimum cutting.
• Multilayered diamond coating for grinding edges and large areas
• High removal and cutting capacity
• Prepare without striations
• Flexible, highly stable disc
• Long service life
PropriétésComparativement à un disque diamanté standard, le disque universel MultiCut se distingue de par la présence d´un grain dia-manté marginal de part et d´autre, avec un diamantage naturel.
Une liaison spéciale garantit des résultats de fraisage optimaux.
• Grain diamanté en plusieurs couches pour le fraisage des bords et des surfaces.
• Retrait important et capacité de coupe élevée.
• Préparation sans laisser de marque
• Flexibilité et stabilité des disques élevée
• Haute durabilité
AnwendungenIm Dentallabor zum:
• Trennen • Vorschleifen
• Separieren • Konturieren
von:
• Keramik • Zirkonoxid
• Edelmetall- und Chrom-Kobalt Legierungen
• Composite
ApplicationsUsed in the dental laboratory for:
• Cutting off • Pretrimming
• Separating • Contouring
of:
• Porcelain • Zirconia
• Precious metal and CrCo alloys
• Composites
utilisationsAu laboratoire de prothèse pour:
• Couper • Préparer
• Séparer • Contourer
de:
• La céramique • De l´oxyde de zirconium
• Des métaux précieux et des alliages cobalt- chrome
• Des composites
AnwendungshinweiseMit leichtem Arbeitsdruck arbeiten
Drehzahlempfehlung 10.000 upm
Instructions for useApply only minimum pressure when prepa-ring.Recommended motor speed 10.000 rpm.
conseils d´utilisationTravailler avec une légère pression.Vitesse de rotation recommandée:10.000 tours/mn.
Mehrschichtig, galvanisch durchsetzte Randdiamantierung.
Multilayered, electroformed diamond coating on the rim
Grain diamanté marginal, en plusieurs couches, infiltré par galvano.
354
p 1
L
L mm 0,30Size 1/10 mm 220Order No. ● ● ● 354.524.220HPISO No. 806 104... 354 524 220
dmax. 15.000
L
354
95
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
DiamantscheibenDiamond DiscsDisques Diamants
opt. d
≤ 180 dopt. 25 000 min-1
≥ 180 dopt. 20 000 min-1
≥ 220 dopt. 15 000 min-1
≥ 300 dopt. 10 000 min-1
MulticutUniversal Diamantscheibe mit mehrschich-tiger, galvanisch durchsetzter Randdia-mantierung für hohe Standzeit und höchste Schnittleistung.
Hergestellt durch Galvanoforming (Galvano-plastik / Elektroforming) bietet die MultiCut Diamantscheibe einzigartige Eigenschaften.
Die mehrschichtige, galvanisch durchsetzte Randdiamantierung garantiert ein Schleifver-halten, ähnlich einer Sinterdiamantscheibe, aber flexibel.
MulticutUniversal diamond disc with a multilayered, electroformed diamond coating on the rim for a long service life and maximum cutting capacity.
The MultiCut diamond disc, manufactured by electroforming, has unique properties.
The multilayered, electroformed diamond coating on the rim ensures a cutting perfor-mance similar to that of a sintered diamond disc, but with a higher degree of flexibility.
MulticutDisque diamanté universel avec un grain dia-manté marginal en plusieurs couches, infilt-ré par galvano pour une grande longévité et une capacité de coupe la plus élevée.
Fabriqué par galvanoforming (galvano-plastie/electroforming), le disque diamanté MultiCut offre des propriétés exceptionnelles.
Le grain diamanté marginal en plusieurs couches et infiltré par galvano garantit une coupe similaire à un disque diamanté par frit-tage, tout en étant souple.
eigenschaftenIm Vergleich mit einer Standart Diamant-scheibe zeichnet sich die MultiCut Universal-scheibe dadurch aus, dass die Randdiaman-tierung durch und durch mit naturdiamanten belegt ist.
Eine Spezialbindung garantiert optimale Schleifergebnisse.
• Mehrschichtige Diamantierung für Kanten und Flächenschliff
• Hohe Abtrag- und Schnittleistung
• Arbeiten ohne Streifenbildung
• Flexible, hohe Scheiben-Stabilität
• Hohe Standzeit
PropertiesUnlike standard diamond discs, the MultiCut universal disc features a diamond-coated rim completely impregnated with natural dia-monds.
Special bonding ensures optimum cutting.
• Multilayered diamond coating for grinding edges and large areas
• High removal and cutting capacity
• Prepare without striations
• Flexible, highly stable disc
• Long service life
PropriétésComparativement à un disque diamanté standard, le disque universel MultiCut se distingue de par la présence d´un grain dia-manté marginal de part et d´autre, avec un diamantage naturel.
Une liaison spéciale garantit des résultats de fraisage optimaux.
• Grain diamanté en plusieurs couches pour le fraisage des bords et des surfaces.
• Retrait important et capacité de coupe élevée.
• Préparation sans laisser de marque
• Flexibilité et stabilité des disques élevée
• Haute durabilité
AnwendungenIm Dentallabor zum:
• Trennen • Vorschleifen
• Separieren • Konturieren
von:
• Keramik • Zirkonoxid
• Edelmetall- und Chrom-Kobalt Legierungen
• Composite
ApplicationsUsed in the dental laboratory for:
• Cutting off • Pretrimming
• Separating • Contouring
of:
• Porcelain • Zirconia
• Precious metal and CrCo alloys
• Composites
utilisationsAu laboratoire de prothèse pour:
• Couper • Préparer
• Séparer • Contourer
de:
• La céramique • De l´oxyde de zirconium
• Des métaux précieux et des alliages cobalt- chrome
• Des composites
AnwendungshinweiseMit leichtem Arbeitsdruck arbeiten
Drehzahlempfehlung 10.000 upm
Instructions for useApply only minimum pressure when prepa-ring.Recommended motor speed 10.000 rpm.
conseils d´utilisationTravailler avec une légère pression.Vitesse de rotation recommandée:10.000 tours/mn.
Mehrschichtig, galvanisch durchsetzte Randdiamantierung.
Multilayered, electroformed diamond coating on the rim
Grain diamanté marginal, en plusieurs couches, infiltré par galvano.
354
p 1
L
L mm 0,30Size 1/10 mm 220Order No. ● ● ● 354.524.220HPISO No. 806 104... 354 524 220
dmax. 15.000
L
95
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
DiamantscheibenDiamond DiscsDisques Diamants
opt. d
≤ 180 dopt. 25 000 min-1
≥ 180 dopt. 20 000 min-1
≥ 220 dopt. 15 000 min-1
≥ 300 dopt. 10 000 min-1
MulticutUniversal Diamantscheibe mit mehrschich-tiger, galvanisch durchsetzter Randdia-mantierung für hohe Standzeit und höchste Schnittleistung.
Hergestellt durch Galvanoforming (Galvano-plastik / Elektroforming) bietet die MultiCut Diamantscheibe einzigartige Eigenschaften.
Die mehrschichtige, galvanisch durchsetzte Randdiamantierung garantiert ein Schleifver-halten, ähnlich einer Sinterdiamantscheibe, aber flexibel.
MulticutUniversal diamond disc with a multilayered, electroformed diamond coating on the rim for a long service life and maximum cutting capacity.
The MultiCut diamond disc, manufactured by electroforming, has unique properties.
The multilayered, electroformed diamond coating on the rim ensures a cutting perfor-mance similar to that of a sintered diamond disc, but with a higher degree of flexibility.
MulticutDisque diamanté universel avec un grain dia-manté marginal en plusieurs couches, infilt-ré par galvano pour une grande longévité et une capacité de coupe la plus élevée.
Fabriqué par galvanoforming (galvano-plastie/electroforming), le disque diamanté MultiCut offre des propriétés exceptionnelles.
Le grain diamanté marginal en plusieurs couches et infiltré par galvano garantit une coupe similaire à un disque diamanté par frit-tage, tout en étant souple.
eigenschaftenIm Vergleich mit einer Standart Diamant-scheibe zeichnet sich die MultiCut Universal-scheibe dadurch aus, dass die Randdiaman-tierung durch und durch mit naturdiamanten belegt ist.
Eine Spezialbindung garantiert optimale Schleifergebnisse.
• Mehrschichtige Diamantierung für Kanten und Flächenschliff
• Hohe Abtrag- und Schnittleistung
• Arbeiten ohne Streifenbildung
• Flexible, hohe Scheiben-Stabilität
• Hohe Standzeit
PropertiesUnlike standard diamond discs, the MultiCut universal disc features a diamond-coated rim completely impregnated with natural dia-monds.
Special bonding ensures optimum cutting.
• Multilayered diamond coating for grinding edges and large areas
• High removal and cutting capacity
• Prepare without striations
• Flexible, highly stable disc
• Long service life
PropriétésComparativement à un disque diamanté standard, le disque universel MultiCut se distingue de par la présence d´un grain dia-manté marginal de part et d´autre, avec un diamantage naturel.
Une liaison spéciale garantit des résultats de fraisage optimaux.
• Grain diamanté en plusieurs couches pour le fraisage des bords et des surfaces.
• Retrait important et capacité de coupe élevée.
• Préparation sans laisser de marque
• Flexibilité et stabilité des disques élevée
• Haute durabilité
AnwendungenIm Dentallabor zum:
• Trennen • Vorschleifen
• Separieren • Konturieren
von:
• Keramik • Zirkonoxid
• Edelmetall- und Chrom-Kobalt Legierungen
• Composite
ApplicationsUsed in the dental laboratory for:
• Cutting off • Pretrimming
• Separating • Contouring
of:
• Porcelain • Zirconia
• Precious metal and CrCo alloys
• Composites
utilisationsAu laboratoire de prothèse pour:
• Couper • Préparer
• Séparer • Contourer
de:
• La céramique • De l´oxyde de zirconium
• Des métaux précieux et des alliages cobalt- chrome
• Des composites
AnwendungshinweiseMit leichtem Arbeitsdruck arbeiten
Drehzahlempfehlung 10.000 upm
Instructions for useApply only minimum pressure when prepa-ring.Recommended motor speed 10.000 rpm.
conseils d´utilisationTravailler avec une légère pression.Vitesse de rotation recommandée:10.000 tours/mn.
Mehrschichtig, galvanisch durchsetzte Randdiamantierung.
Multilayered, electroformed diamond coating on the rim
Grain diamanté marginal, en plusieurs couches, infiltré par galvano.
354
p 1
L
L mm 0,30Size 1/10 mm 220Order No. ● ● ● 354.524.220HPISO No. 806 104... 354 524 220
dmax. 15.000
L
MultiCut
94
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
suPerflex TurBOIn superfeiner und feiner Diamantkörnung für Keramik, Composites, Kunststoffe, die Spirale ermöglicht einen schnellen, optimalen Abtrans-port des Schleifgutes, zum Konturieren, zum Trennen von Zahnkränzen an Sägemodellen.
In superfine and fine diamond grit for ceramics, composites and acrylics. The spiral cut enables effortless permanent removal of residue for con-touring and separating of saw-cut models.
En grain diamanté fin et extra fin pour céra-miques, composites et acryliques. La spirale permet un dégagement efficace des copeaux d’usinages, pour séparer et contourer des modèles de scie.
Trennscheibe 378mit beidseitiger Diamant-Vollbelegung zum Separieren und Trennen von Press-Muffeln. Eine spezielle Segmentierung verhindert ein Verklem-men oder Einhaken der Scheibe.
cut-off disc 378coated on both sides for separating and cutting off press moulds. Provided with segmentation wich preventing jamming or catching of the disc.
Disque à tronçonner 378entiere ment diamantés sur les deux faces pour séparer et sectionnner les moules de pressage. Avec une segmentation pour d‘éviter ainsi un blocage ou un accrochage du disque.
flex TurBOIn standard Diamantkörnung, die Spirale ermög-licht einen schnellen und optimalen Abtransport des Schleifgutes, zum Separieren von Kunststoff und Keramik, kein Verschmieren.
In standard diamond grit, the spiral cut enables a quick and optimum removal of residue for sepa-rating of acrylics and ceramics, no smearing.
En grain diamanté standard, la spirale assure un dégagement efficace des copeaux d’usinages, pour la séparation des acryliques et des céra-miques, ne colore pas la matière.
505
p 1
L
L mm 0,12 0,12 0,12Size 1/10 mm 160 190 220Order No. ● 505.504.160HP ● 505.504.190HP ● 505.504.220HPISO No. 806 104... 505 504 160 505 504 190 505 504 220
dmax. 20.000 20.000 20.000
L
505
p 1
L
L
L mm 0,15 0,15Size 1/10 mm 190 220Order No. ● 505.514.190HP ● 505.514.220HPISO No. 806 104... 505 514 190 505 514 220
dmax. 20.000 20.000
362
p 1
L
L mm 0,30 0,30Size 1/10 mm 080 100Order No. ● 362.524.080HP ● 362.524.100HPISO No. 806 104... 362 524 080 362 524 100
dmax. 25.000 25.000
L
378
p 1
L mm 0,35Size 1/10 mm 450Order No. ● 378.524.450HPISO No. 806 104... 378 524 450
dmax. 10.000
L
↶↶95
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
DiamantscheibenDiamond DiscsDisques Diamants
opt. d
≤ 180 dopt. 25 000 min-1
≥ 180 dopt. 20 000 min-1
≥ 220 dopt. 15 000 min-1
≥ 300 dopt. 10 000 min-1
MulticutUniversal Diamantscheibe mit mehrschich-tiger, galvanisch durchsetzter Randdia-mantierung für hohe Standzeit und höchste Schnittleistung.
Hergestellt durch Galvanoforming (Galvano-plastik / Elektroforming) bietet die MultiCut Diamantscheibe einzigartige Eigenschaften.
Die mehrschichtige, galvanisch durchsetzte Randdiamantierung garantiert ein Schleifver-halten, ähnlich einer Sinterdiamantscheibe, aber flexibel.
MulticutUniversal diamond disc with a multilayered, electroformed diamond coating on the rim for a long service life and maximum cutting capacity.
The MultiCut diamond disc, manufactured by electroforming, has unique properties.
The multilayered, electroformed diamond coating on the rim ensures a cutting perfor-mance similar to that of a sintered diamond disc, but with a higher degree of flexibility.
MulticutDisque diamanté universel avec un grain dia-manté marginal en plusieurs couches, infilt-ré par galvano pour une grande longévité et une capacité de coupe la plus élevée.
Fabriqué par galvanoforming (galvano-plastie/electroforming), le disque diamanté MultiCut offre des propriétés exceptionnelles.
Le grain diamanté marginal en plusieurs couches et infiltré par galvano garantit une coupe similaire à un disque diamanté par frit-tage, tout en étant souple.
eigenschaftenIm Vergleich mit einer Standart Diamant-scheibe zeichnet sich die MultiCut Universal-scheibe dadurch aus, dass die Randdiaman-tierung durch und durch mit naturdiamanten belegt ist.
Eine Spezialbindung garantiert optimale Schleifergebnisse.
• Mehrschichtige Diamantierung für Kanten und Flächenschliff
• Hohe Abtrag- und Schnittleistung
• Arbeiten ohne Streifenbildung
• Flexible, hohe Scheiben-Stabilität
• Hohe Standzeit
PropertiesUnlike standard diamond discs, the MultiCut universal disc features a diamond-coated rim completely impregnated with natural dia-monds.
Special bonding ensures optimum cutting.
• Multilayered diamond coating for grinding edges and large areas
• High removal and cutting capacity
• Prepare without striations
• Flexible, highly stable disc
• Long service life
PropriétésComparativement à un disque diamanté standard, le disque universel MultiCut se distingue de par la présence d´un grain dia-manté marginal de part et d´autre, avec un diamantage naturel.
Une liaison spéciale garantit des résultats de fraisage optimaux.
• Grain diamanté en plusieurs couches pour le fraisage des bords et des surfaces.
• Retrait important et capacité de coupe élevée.
• Préparation sans laisser de marque
• Flexibilité et stabilité des disques élevée
• Haute durabilité
AnwendungenIm Dentallabor zum:
• Trennen • Vorschleifen
• Separieren • Konturieren
von:
• Keramik • Zirkonoxid
• Edelmetall- und Chrom-Kobalt Legierungen
• Composite
ApplicationsUsed in the dental laboratory for:
• Cutting off • Pretrimming
• Separating • Contouring
of:
• Porcelain • Zirconia
• Precious metal and CrCo alloys
• Composites
utilisationsAu laboratoire de prothèse pour:
• Couper • Préparer
• Séparer • Contourer
de:
• La céramique • De l´oxyde de zirconium
• Des métaux précieux et des alliages cobalt- chrome
• Des composites
AnwendungshinweiseMit leichtem Arbeitsdruck arbeiten
Drehzahlempfehlung 10.000 upm
Instructions for useApply only minimum pressure when prepa-ring.Recommended motor speed 10.000 rpm.
conseils d´utilisationTravailler avec une légère pression.Vitesse de rotation recommandée:10.000 tours/mn.
Mehrschichtig, galvanisch durchsetzte Randdiamantierung.
Multilayered, electroformed diamond coating on the rim
Grain diamanté marginal, en plusieurs couches, infiltré par galvano.
354
p 1
L
L mm 0,30Size 1/10 mm 220Order No. ● ● ● 354.524.220HPISO No. 806 104... 354 524 220
dmax. 15.000
L
Diamond Discs
L mm 0,12 0,12 0,12
Size 1/10 mm • 160 • 190 • 220
Order No. SET643 SET644 SET645
↻max. 20,000 20,000 20,000
L mm 0,15 0,15
Size 1/10 mm • 190 • 220
Order No. SET646 SET647
↻max. 20,000 20,000
L mm 0,30 0,30
Size 1/10 mm • 080 • 100
Order No. SET641 SET642
↻max. 25,000 25,000
L mm 0,30
Size 1/10 mm ••• 220
Order No. SET649
↻max. 15,000
95
DIAMANTscheIBeN • DIAMOND DIscs • DIsques DIAMANTs
DiamantscheibenDiamond DiscsDisques Diamants
opt. d
≤ 180 dopt. 25 000 min-1
≥ 180 dopt. 20 000 min-1
≥ 220 dopt. 15 000 min-1
≥ 300 dopt. 10 000 min-1
MulticutUniversal Diamantscheibe mit mehrschich-tiger, galvanisch durchsetzter Randdia-mantierung für hohe Standzeit und höchste Schnittleistung.
Hergestellt durch Galvanoforming (Galvano-plastik / Elektroforming) bietet die MultiCut Diamantscheibe einzigartige Eigenschaften.
Die mehrschichtige, galvanisch durchsetzte Randdiamantierung garantiert ein Schleifver-halten, ähnlich einer Sinterdiamantscheibe, aber flexibel.
MulticutUniversal diamond disc with a multilayered, electroformed diamond coating on the rim for a long service life and maximum cutting capacity.
The MultiCut diamond disc, manufactured by electroforming, has unique properties.
The multilayered, electroformed diamond coating on the rim ensures a cutting perfor-mance similar to that of a sintered diamond disc, but with a higher degree of flexibility.
MulticutDisque diamanté universel avec un grain dia-manté marginal en plusieurs couches, infilt-ré par galvano pour une grande longévité et une capacité de coupe la plus élevée.
Fabriqué par galvanoforming (galvano-plastie/electroforming), le disque diamanté MultiCut offre des propriétés exceptionnelles.
Le grain diamanté marginal en plusieurs couches et infiltré par galvano garantit une coupe similaire à un disque diamanté par frit-tage, tout en étant souple.
eigenschaftenIm Vergleich mit einer Standart Diamant-scheibe zeichnet sich die MultiCut Universal-scheibe dadurch aus, dass die Randdiaman-tierung durch und durch mit naturdiamanten belegt ist.
Eine Spezialbindung garantiert optimale Schleifergebnisse.
• Mehrschichtige Diamantierung für Kanten und Flächenschliff
• Hohe Abtrag- und Schnittleistung
• Arbeiten ohne Streifenbildung
• Flexible, hohe Scheiben-Stabilität
• Hohe Standzeit
PropertiesUnlike standard diamond discs, the MultiCut universal disc features a diamond-coated rim completely impregnated with natural dia-monds.
Special bonding ensures optimum cutting.
• Multilayered diamond coating for grinding edges and large areas
• High removal and cutting capacity
• Prepare without striations
• Flexible, highly stable disc
• Long service life
PropriétésComparativement à un disque diamanté standard, le disque universel MultiCut se distingue de par la présence d´un grain dia-manté marginal de part et d´autre, avec un diamantage naturel.
Une liaison spéciale garantit des résultats de fraisage optimaux.
• Grain diamanté en plusieurs couches pour le fraisage des bords et des surfaces.
• Retrait important et capacité de coupe élevée.
• Préparation sans laisser de marque
• Flexibilité et stabilité des disques élevée
• Haute durabilité
AnwendungenIm Dentallabor zum:
• Trennen • Vorschleifen
• Separieren • Konturieren
von:
• Keramik • Zirkonoxid
• Edelmetall- und Chrom-Kobalt Legierungen
• Composite
ApplicationsUsed in the dental laboratory for:
• Cutting off • Pretrimming
• Separating • Contouring
of:
• Porcelain • Zirconia
• Precious metal and CrCo alloys
• Composites
utilisationsAu laboratoire de prothèse pour:
• Couper • Préparer
• Séparer • Contourer
de:
• La céramique • De l´oxyde de zirconium
• Des métaux précieux et des alliages cobalt- chrome
• Des composites
AnwendungshinweiseMit leichtem Arbeitsdruck arbeiten
Drehzahlempfehlung 10.000 upm
Instructions for useApply only minimum pressure when prepa-ring.Recommended motor speed 10.000 rpm.
conseils d´utilisationTravailler avec une légère pression.Vitesse de rotation recommandée:10.000 tours/mn.
Mehrschichtig, galvanisch durchsetzte Randdiamantierung.
Multilayered, electroformed diamond coating on the rim
Grain diamanté marginal, en plusieurs couches, infiltré par galvano.
354
p 1
L
L mm 0,30Size 1/10 mm 220Order No. ● ● ● 354.524.220HPISO No. 806 104... 354 524 220
dmax. 15.000
L
35
96
sINTer-DIAMANTeN • sINTereD DIAMONDs • DIAMANTs DANs lA MAsse
Formgebung und GrobsubstanzreduktionShaping and bulk substance reductionFaconnage et grande réduction
Ausarbeiten von ModellgussTrimming cobalt chrome.Traitement de la coulée des modèles
Konturieren von Keramik und VollkeramikContouring of porcelain and composite veneersContourer les incrustations en céramique ou en résine
Okklusale Fissurengestaltung und KonturierungOcclusal fissuring and contouringFaconnage des sillions occlusales et contourage
sinterdiamantenImmer neue Werkstoffe erfordern verbesserte Instrumente zur Bearbeitung. Dabei sollte ein solches Instrument möglichst universell für viele Materialien einsetzbar sein. Sinterdiamanten bie-ten in der Zahntechnik Zeit- und Kostenvorteile bei jeder Anwendung.
Im Gegensatz zu galvanischen Schleifern, die nur mit einer Diamantschicht belegt sind, bestehen Sinterdiamanten durch und durch aus Diamanten, die von einer Metallverbindung gehalten werden. Die für Sinterdiamanten verwendete Diamant-qualität und die Spezial-Metallbindung garantieren ideale Schleifergebnisse.
Diamants dans la masseL’évolution des divers matériaux nécessite des instruments toujours plus performants pour leur usinage. Il est important qu’un tel instrument puisse être appliqué pour les matériaux les plus divers possible. Les instruments diamantés par frittage offre des avantages en terme de coûts et temps de préparation, au laboratoire de prothèse.
Contrairement aux instruments diamantés par galvanoplastie qui ne comporte qu’une couche de diamants, les instruments diamantés par frit-tage sont diamantés dans la masse. Les grains diamantés sont réalisés avec un liant métallique, compatible avec les céramiques. La qualité des grains diamantés utilisés pour les instruments diamantés par frittage, ainsi que le liant métal-lique spécial, garantissent d’excellents résultats.
sintered Diamondsnew materials necessitate improved and upda-ted instruments. It is equally important for these instruments to be as universal as possible for use. Sintered Diamond Instruments are cost-effective and time-saving and can be used for all kinds of applications in the Dental Laboratory.
Whilst galvanic grinders are only covered with a diamond coating, Sintered Diamonds consist of diamonds throughout, with a metal bond for firm hold. The high quality diamond grit and finest special metal bond used for the manufacture of Sintered Diamond Instruments are providing an absolute guarantee for achieving ultimate grinding results.
96
sINTer-DIAMANTeN • sINTereD DIAMONDs • DIAMANTs DANs lA MAsse
Formgebung und GrobsubstanzreduktionShaping and bulk substance reductionFaconnage et grande réduction
Ausarbeiten von ModellgussTrimming cobalt chrome.Traitement de la coulée des modèles
Konturieren von Keramik und VollkeramikContouring of porcelain and composite veneersContourer les incrustations en céramique ou en résine
Okklusale Fissurengestaltung und KonturierungOcclusal fissuring and contouringFaconnage des sillions occlusales et contourage
sinterdiamantenImmer neue Werkstoffe erfordern verbesserte Instrumente zur Bearbeitung. Dabei sollte ein solches Instrument möglichst universell für viele Materialien einsetzbar sein. Sinterdiamanten bie-ten in der Zahntechnik Zeit- und Kostenvorteile bei jeder Anwendung.
Im Gegensatz zu galvanischen Schleifern, die nur mit einer Diamantschicht belegt sind, bestehen Sinterdiamanten durch und durch aus Diamanten, die von einer Metallverbindung gehalten werden. Die für Sinterdiamanten verwendete Diamant-qualität und die Spezial-Metallbindung garantieren ideale Schleifergebnisse.
Diamants dans la masseL’évolution des divers matériaux nécessite des instruments toujours plus performants pour leur usinage. Il est important qu’un tel instrument puisse être appliqué pour les matériaux les plus divers possible. Les instruments diamantés par frittage offre des avantages en terme de coûts et temps de préparation, au laboratoire de prothèse.
Contrairement aux instruments diamantés par galvanoplastie qui ne comporte qu’une couche de diamants, les instruments diamantés par frit-tage sont diamantés dans la masse. Les grains diamantés sont réalisés avec un liant métallique, compatible avec les céramiques. La qualité des grains diamantés utilisés pour les instruments diamantés par frittage, ainsi que le liant métal-lique spécial, garantissent d’excellents résultats.
sintered Diamondsnew materials necessitate improved and upda-ted instruments. It is equally important for these instruments to be as universal as possible for use. Sintered Diamond Instruments are cost-effective and time-saving and can be used for all kinds of applications in the Dental Laboratory.
Whilst galvanic grinders are only covered with a diamond coating, Sintered Diamonds consist of diamonds throughout, with a metal bond for firm hold. The high quality diamond grit and finest special metal bond used for the manufacture of Sintered Diamond Instruments are providing an absolute guarantee for achieving ultimate grinding results.
Shaping and bulk substance reduction.
Trimming colbalt chrome.
96
sINTer-DIAMANTeN • sINTereD DIAMONDs • DIAMANTs DANs lA MAsse
Formgebung und GrobsubstanzreduktionShaping and bulk substance reductionFaconnage et grande réduction
Ausarbeiten von ModellgussTrimming cobalt chrome.Traitement de la coulée des modèles
Konturieren von Keramik und VollkeramikContouring of porcelain and composite veneersContourer les incrustations en céramique ou en résine
Okklusale Fissurengestaltung und KonturierungOcclusal fissuring and contouringFaconnage des sillions occlusales et contourage
sinterdiamantenImmer neue Werkstoffe erfordern verbesserte Instrumente zur Bearbeitung. Dabei sollte ein solches Instrument möglichst universell für viele Materialien einsetzbar sein. Sinterdiamanten bie-ten in der Zahntechnik Zeit- und Kostenvorteile bei jeder Anwendung.
Im Gegensatz zu galvanischen Schleifern, die nur mit einer Diamantschicht belegt sind, bestehen Sinterdiamanten durch und durch aus Diamanten, die von einer Metallverbindung gehalten werden. Die für Sinterdiamanten verwendete Diamant-qualität und die Spezial-Metallbindung garantieren ideale Schleifergebnisse.
Diamants dans la masseL’évolution des divers matériaux nécessite des instruments toujours plus performants pour leur usinage. Il est important qu’un tel instrument puisse être appliqué pour les matériaux les plus divers possible. Les instruments diamantés par frittage offre des avantages en terme de coûts et temps de préparation, au laboratoire de prothèse.
Contrairement aux instruments diamantés par galvanoplastie qui ne comporte qu’une couche de diamants, les instruments diamantés par frit-tage sont diamantés dans la masse. Les grains diamantés sont réalisés avec un liant métallique, compatible avec les céramiques. La qualité des grains diamantés utilisés pour les instruments diamantés par frittage, ainsi que le liant métal-lique spécial, garantissent d’excellents résultats.
sintered Diamondsnew materials necessitate improved and upda-ted instruments. It is equally important for these instruments to be as universal as possible for use. Sintered Diamond Instruments are cost-effective and time-saving and can be used for all kinds of applications in the Dental Laboratory.
Whilst galvanic grinders are only covered with a diamond coating, Sintered Diamonds consist of diamonds throughout, with a metal bond for firm hold. The high quality diamond grit and finest special metal bond used for the manufacture of Sintered Diamond Instruments are providing an absolute guarantee for achieving ultimate grinding results.
96
sINTer-DIAMANTeN • sINTereD DIAMONDs • DIAMANTs DANs lA MAsse
Formgebung und GrobsubstanzreduktionShaping and bulk substance reductionFaconnage et grande réduction
Ausarbeiten von ModellgussTrimming cobalt chrome.Traitement de la coulée des modèles
Konturieren von Keramik und VollkeramikContouring of porcelain and composite veneersContourer les incrustations en céramique ou en résine
Okklusale Fissurengestaltung und KonturierungOcclusal fissuring and contouringFaconnage des sillions occlusales et contourage
sinterdiamantenImmer neue Werkstoffe erfordern verbesserte Instrumente zur Bearbeitung. Dabei sollte ein solches Instrument möglichst universell für viele Materialien einsetzbar sein. Sinterdiamanten bie-ten in der Zahntechnik Zeit- und Kostenvorteile bei jeder Anwendung.
Im Gegensatz zu galvanischen Schleifern, die nur mit einer Diamantschicht belegt sind, bestehen Sinterdiamanten durch und durch aus Diamanten, die von einer Metallverbindung gehalten werden. Die für Sinterdiamanten verwendete Diamant-qualität und die Spezial-Metallbindung garantieren ideale Schleifergebnisse.
Diamants dans la masseL’évolution des divers matériaux nécessite des instruments toujours plus performants pour leur usinage. Il est important qu’un tel instrument puisse être appliqué pour les matériaux les plus divers possible. Les instruments diamantés par frittage offre des avantages en terme de coûts et temps de préparation, au laboratoire de prothèse.
Contrairement aux instruments diamantés par galvanoplastie qui ne comporte qu’une couche de diamants, les instruments diamantés par frit-tage sont diamantés dans la masse. Les grains diamantés sont réalisés avec un liant métallique, compatible avec les céramiques. La qualité des grains diamantés utilisés pour les instruments diamantés par frittage, ainsi que le liant métal-lique spécial, garantissent d’excellents résultats.
sintered Diamondsnew materials necessitate improved and upda-ted instruments. It is equally important for these instruments to be as universal as possible for use. Sintered Diamond Instruments are cost-effective and time-saving and can be used for all kinds of applications in the Dental Laboratory.
Whilst galvanic grinders are only covered with a diamond coating, Sintered Diamonds consist of diamonds throughout, with a metal bond for firm hold. The high quality diamond grit and finest special metal bond used for the manufacture of Sintered Diamond Instruments are providing an absolute guarantee for achieving ultimate grinding results.
101
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Nr. 9900sO
Nr. 5000sO
Nr. 5100sO
5110 – 90510751095111510651085105
Seite / Page
5025 5022
5028 5008
5024 5009
5110 5107
5109 5111
5106
5108 5105
5025 – 9050225028500850245009
Seite / Page
5106 – 905332 – 915117 – 905211 – 915115 – 905209 – 91
Seite / Page
5106 5332
5117 5211
5115 5209
101
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Nr. 9900sO
Nr. 5000sO
Nr. 5100sO
5110 – 90510751095111510651085105
Seite / Page
5025 5022
5028 5008
5024 5009
5110 5107
5109 5111
5106
5108 5105
5025 – 9050225028500850245009
Seite / Page
5106 – 905332 – 915117 – 905211 – 915115 – 905209 – 91
Seite / Page
5106 5332
5117 5211
5115 5209
100
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Indikation− Hartmetall-gebundene Sinterdiamanten zur
optimalen Bearbeitung von Keramiken und nE-Metallen
standard-sortiment Nr. 9900sO7 Formen, mittlerer Körnung
− Sinterdiamenten sind besonders wirtschaft-liche, sichere und effiziente Instrumente
− die spezielle Bindung setzt ständig neue Diamanten frei und ermöglicht dadurch das permanent scharfe Schleifen
− der Schaft aus Spezialstahl erlaubt vibra-tionsfreies Arbeiten
− Standard-Sortiment enthält die gängigsten Formen in Standardausführung zur Ausar-beitung aller nE-, Chrom-Kobalt-, Titan- und Gold-Legierungen
Indications− TC-bonded Sintered Diamonds are ideal
instruments for surface treatment of ceramics and nP metals
standard-Assortment Nr. 9900sO7 shapes in medium grit
− Sintered Diamonds are highly economical, safe and efficient instruments
− the special diamond-impregnated metal bond continuously releases diamond par-ticles and therefore permanently ensures sharp cutting properties
− shafts are made of a special steel which allows vibration-free handling
− standard assortment contains most popular shapes for utilisation on nP, chrome-cobalt, and titanium alloys-and precious alloys
Indication− Instruments diamantés par frittage à liant
carbure, pour le façonnage optimal des céramiques et des alliages nP
Assortiment standard No 9900sO7 formes, grain moyen
− Les instruments diamantés par frittage sont des instruments particulièrement écono-miques, sûrs et efficaces
− Le système de liaison spécial libère con-stamment des nouvelles particules de dia-mant, ainsi l’effet abrasif est toujours parfait
− La tige en acier spécial permet un travail sans aucune vibration
− L’assortiment standard comprend les formes les plus courantes du type standard pour le travail de tous les alliages, nP, chrome-cobalt, titane et précieux
Keramik-sortiment Nr. 5000sO6 Formen, feiner Körnung
− feine Körnung in der Hartmetallbindung sichert glatten Schliff
− dadurch wenig nacharbeit und geringe Verlet-zungsgefahr für die Keramikoberfläche
− Kelchformen behalten eine permanent scharfe Kante, die sich ideal für Fissuren- und Struk-turgestaltung eignet
ceramics Assortment Nr.5000sO6 shapes in fine grit
− the fine grit of TC-bonded diamonds ensures smooth cutting properties
− therefore, hardly any rework is necessary and the ceramic surface remains undamaged
− cone-shaped instruments permanently retain shapes edges and are, therefore, perfectly sui-table for fissure and structure creation
Assortiment céramique No 5000sO6 formes, grain fin
− Le grain fin pris dans le liant carbure garantit l’obtention d’une surface lisse après meulage
− Ainsi, peu de retouches sont nécessaires et il y a peu de risque de détériorer la surface des céramiques
− Les formes en cône renversé gardent en per-manence une arrête vive idéalement adaptée pour le façonnage de sillons et des reliefs
Ne-sortiment Nr. 5100sO6 Formen, 3 Körnungen
− die unterschiedlichen Diamantkörnungen des Sortiments sind mit Farbringen versehen
− sie ermöglichen die optimale Bearbeitung jeder nE-Legierung, von der groben Vorarbeit bis zum Feinschliff
− die verschiedenen Formen erlauben sowohl die Bearbeitung von grazilen Bereichen wie die abrasive, grossflächige Ausarbeitung
− die Hartmetallbidung garantiert eine lange Standzeit auf jeder Legierung
NP Assortment No 5100sO6 shapes in 3 grit versions
− these colour-coded sintered diamonds are custom-selected in a variance of grits
− this caters for the entire task range of nP allo-ys, starting from pre-grinding to fine precision work
− various shapes in turn allow all steps from gross reduction right up to treatment of the most delicate areas
− the TC-bond guarantees excellent durability on any alloy
Assortiment NP No 5100sO6 formes, 3 grains différents
− Les grains de tailles différentes des particu-les de diamant composant l’assor-timent sont signalés à l’aide d’anneaux colorés
− Ces divers grains permettent un usinage opti-mal, allant du dégrossissage à la finition, de tous les alliages nP
− Les formes différentes permettent d’usiner tout aussi bien les zones les plus menues que de larges surfaces
− La liaison carbure garantit une grande durée de vie quel que soit l’alliage usineé
Technische Details− Drehzahlempfehlung für alle nE-Metalle &
Keramiken – unbedingt drucklos arbeiten− max. 25.000 upm− zur Erhaltung der Schleifleistung ist der Sin-
terdiamant immer mit dem Reinigungsstein no 9920 abzuziehen
Technical Details− speed recommendation on all nP alloys and
ceramics - pressure-free application impera-tive
− 25.000 rpm max.− always use a dressing stone to retain cutting properties of sintered diamonds - fig.
no 9920 refers
Détails techniques− Vitesses de rotation conseillées pour tous
les métaux nP et les céramiques - travaillez toujours en n’exerçant aucune pression
− Max. 25’000 trs/min.− Pour conserver son pouvoir abrasif, l’instru-
ment diamanté par frittage doit toujours être passé sur une pierre de nettoyage - voir fig.
no 9920
101
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Nr. 9900sO
Nr. 5000sO
Nr. 5100sO
5110 – 90510751095111510651085105
Seite / Page
5025 5022
5028 5008
5024 5009
5110 5107
5109 5111
5106
5108 5105
5025 – 9050225028500850245009
Seite / Page
5106 – 905332 – 915117 – 905211 – 915115 – 905209 – 91
Seite / Page
5106 5332
5117 5211
5115 5209
101
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Nr. 9900sO
Nr. 5000sO
Nr. 5100sO
5110 – 90510751095111510651085105
Seite / Page
5025 5022
5028 5008
5024 5009
5110 5107
5109 5111
5106
5108 5105
5025 – 9050225028500850245009
Seite / Page
5106 – 905332 – 915117 – 905211 – 915115 – 905209 – 91
Seite / Page
5106 5332
5117 5211
5115 5209
101
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Nr. 9900sO
Nr. 5000sO
Nr. 5100sO
5110 – 90510751095111510651085105
Seite / Page
5025 5022
5028 5008
5024 5009
5110 5107
5109 5111
5106
5108 5105
5025 – 9050225028500850245009
Seite / Page
5106 – 905332 – 915117 – 905211 – 915115 – 905209 – 91
Seite / Page
5106 5332
5117 5211
5115 5209
101
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Nr. 9900sO
Nr. 5000sO
Nr. 5100sO
5110 – 90510751095111510651085105
Seite / Page
5025 5022
5028 5008
5024 5009
5110 5107
5109 5111
5106
5108 5105
5025 – 9050225028500850245009
Seite / Page
5106 – 905332 – 915117 – 905211 – 915115 – 905209 – 91
Seite / Page
5106 5332
5117 5211
5115 5209
100
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Indikation− Hartmetall-gebundene Sinterdiamanten zur
optimalen Bearbeitung von Keramiken und nE-Metallen
standard-sortiment Nr. 9900sO7 Formen, mittlerer Körnung
− Sinterdiamenten sind besonders wirtschaft-liche, sichere und effiziente Instrumente
− die spezielle Bindung setzt ständig neue Diamanten frei und ermöglicht dadurch das permanent scharfe Schleifen
− der Schaft aus Spezialstahl erlaubt vibra-tionsfreies Arbeiten
− Standard-Sortiment enthält die gängigsten Formen in Standardausführung zur Ausar-beitung aller nE-, Chrom-Kobalt-, Titan- und Gold-Legierungen
Indications− TC-bonded Sintered Diamonds are ideal
instruments for surface treatment of ceramics and nP metals
standard-Assortment Nr. 9900sO7 shapes in medium grit
− Sintered Diamonds are highly economical, safe and efficient instruments
− the special diamond-impregnated metal bond continuously releases diamond par-ticles and therefore permanently ensures sharp cutting properties
− shafts are made of a special steel which allows vibration-free handling
− standard assortment contains most popular shapes for utilisation on nP, chrome-cobalt, and titanium alloys-and precious alloys
Indication− Instruments diamantés par frittage à liant
carbure, pour le façonnage optimal des céramiques et des alliages nP
Assortiment standard No 9900sO7 formes, grain moyen
− Les instruments diamantés par frittage sont des instruments particulièrement écono-miques, sûrs et efficaces
− Le système de liaison spécial libère con-stamment des nouvelles particules de dia-mant, ainsi l’effet abrasif est toujours parfait
− La tige en acier spécial permet un travail sans aucune vibration
− L’assortiment standard comprend les formes les plus courantes du type standard pour le travail de tous les alliages, nP, chrome-cobalt, titane et précieux
Keramik-sortiment Nr. 5000sO6 Formen, feiner Körnung
− feine Körnung in der Hartmetallbindung sichert glatten Schliff
− dadurch wenig nacharbeit und geringe Verlet-zungsgefahr für die Keramikoberfläche
− Kelchformen behalten eine permanent scharfe Kante, die sich ideal für Fissuren- und Struk-turgestaltung eignet
ceramics Assortment Nr.5000sO6 shapes in fine grit
− the fine grit of TC-bonded diamonds ensures smooth cutting properties
− therefore, hardly any rework is necessary and the ceramic surface remains undamaged
− cone-shaped instruments permanently retain shapes edges and are, therefore, perfectly sui-table for fissure and structure creation
Assortiment céramique No 5000sO6 formes, grain fin
− Le grain fin pris dans le liant carbure garantit l’obtention d’une surface lisse après meulage
− Ainsi, peu de retouches sont nécessaires et il y a peu de risque de détériorer la surface des céramiques
− Les formes en cône renversé gardent en per-manence une arrête vive idéalement adaptée pour le façonnage de sillons et des reliefs
Ne-sortiment Nr. 5100sO6 Formen, 3 Körnungen
− die unterschiedlichen Diamantkörnungen des Sortiments sind mit Farbringen versehen
− sie ermöglichen die optimale Bearbeitung jeder nE-Legierung, von der groben Vorarbeit bis zum Feinschliff
− die verschiedenen Formen erlauben sowohl die Bearbeitung von grazilen Bereichen wie die abrasive, grossflächige Ausarbeitung
− die Hartmetallbidung garantiert eine lange Standzeit auf jeder Legierung
NP Assortment No 5100sO6 shapes in 3 grit versions
− these colour-coded sintered diamonds are custom-selected in a variance of grits
− this caters for the entire task range of nP allo-ys, starting from pre-grinding to fine precision work
− various shapes in turn allow all steps from gross reduction right up to treatment of the most delicate areas
− the TC-bond guarantees excellent durability on any alloy
Assortiment NP No 5100sO6 formes, 3 grains différents
− Les grains de tailles différentes des particu-les de diamant composant l’assor-timent sont signalés à l’aide d’anneaux colorés
− Ces divers grains permettent un usinage opti-mal, allant du dégrossissage à la finition, de tous les alliages nP
− Les formes différentes permettent d’usiner tout aussi bien les zones les plus menues que de larges surfaces
− La liaison carbure garantit une grande durée de vie quel que soit l’alliage usineé
Technische Details− Drehzahlempfehlung für alle nE-Metalle &
Keramiken – unbedingt drucklos arbeiten− max. 25.000 upm− zur Erhaltung der Schleifleistung ist der Sin-
terdiamant immer mit dem Reinigungsstein no 9920 abzuziehen
Technical Details− speed recommendation on all nP alloys and
ceramics - pressure-free application impera-tive
− 25.000 rpm max.− always use a dressing stone to retain cutting properties of sintered diamonds - fig.
no 9920 refers
Détails techniques− Vitesses de rotation conseillées pour tous
les métaux nP et les céramiques - travaillez toujours en n’exerçant aucune pression
− Max. 25’000 trs/min.− Pour conserver son pouvoir abrasif, l’instru-
ment diamanté par frittage doit toujours être passé sur une pierre de nettoyage - voir fig.
no 9920
100
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
Indikation− Hartmetall-gebundene Sinterdiamanten zur
optimalen Bearbeitung von Keramiken und nE-Metallen
standard-sortiment Nr. 9900sO7 Formen, mittlerer Körnung
− Sinterdiamenten sind besonders wirtschaft-liche, sichere und effiziente Instrumente
− die spezielle Bindung setzt ständig neue Diamanten frei und ermöglicht dadurch das permanent scharfe Schleifen
− der Schaft aus Spezialstahl erlaubt vibra-tionsfreies Arbeiten
− Standard-Sortiment enthält die gängigsten Formen in Standardausführung zur Ausar-beitung aller nE-, Chrom-Kobalt-, Titan- und Gold-Legierungen
Indications− TC-bonded Sintered Diamonds are ideal
instruments for surface treatment of ceramics and nP metals
standard-Assortment Nr. 9900sO7 shapes in medium grit
− Sintered Diamonds are highly economical, safe and efficient instruments
− the special diamond-impregnated metal bond continuously releases diamond par-ticles and therefore permanently ensures sharp cutting properties
− shafts are made of a special steel which allows vibration-free handling
− standard assortment contains most popular shapes for utilisation on nP, chrome-cobalt, and titanium alloys-and precious alloys
Indication− Instruments diamantés par frittage à liant
carbure, pour le façonnage optimal des céramiques et des alliages nP
Assortiment standard No 9900sO7 formes, grain moyen
− Les instruments diamantés par frittage sont des instruments particulièrement écono-miques, sûrs et efficaces
− Le système de liaison spécial libère con-stamment des nouvelles particules de dia-mant, ainsi l’effet abrasif est toujours parfait
− La tige en acier spécial permet un travail sans aucune vibration
− L’assortiment standard comprend les formes les plus courantes du type standard pour le travail de tous les alliages, nP, chrome-cobalt, titane et précieux
Keramik-sortiment Nr. 5000sO6 Formen, feiner Körnung
− feine Körnung in der Hartmetallbindung sichert glatten Schliff
− dadurch wenig nacharbeit und geringe Verlet-zungsgefahr für die Keramikoberfläche
− Kelchformen behalten eine permanent scharfe Kante, die sich ideal für Fissuren- und Struk-turgestaltung eignet
ceramics Assortment Nr.5000sO6 shapes in fine grit
− the fine grit of TC-bonded diamonds ensures smooth cutting properties
− therefore, hardly any rework is necessary and the ceramic surface remains undamaged
− cone-shaped instruments permanently retain shapes edges and are, therefore, perfectly sui-table for fissure and structure creation
Assortiment céramique No 5000sO6 formes, grain fin
− Le grain fin pris dans le liant carbure garantit l’obtention d’une surface lisse après meulage
− Ainsi, peu de retouches sont nécessaires et il y a peu de risque de détériorer la surface des céramiques
− Les formes en cône renversé gardent en per-manence une arrête vive idéalement adaptée pour le façonnage de sillons et des reliefs
Ne-sortiment Nr. 5100sO6 Formen, 3 Körnungen
− die unterschiedlichen Diamantkörnungen des Sortiments sind mit Farbringen versehen
− sie ermöglichen die optimale Bearbeitung jeder nE-Legierung, von der groben Vorarbeit bis zum Feinschliff
− die verschiedenen Formen erlauben sowohl die Bearbeitung von grazilen Bereichen wie die abrasive, grossflächige Ausarbeitung
− die Hartmetallbidung garantiert eine lange Standzeit auf jeder Legierung
NP Assortment No 5100sO6 shapes in 3 grit versions
− these colour-coded sintered diamonds are custom-selected in a variance of grits
− this caters for the entire task range of nP allo-ys, starting from pre-grinding to fine precision work
− various shapes in turn allow all steps from gross reduction right up to treatment of the most delicate areas
− the TC-bond guarantees excellent durability on any alloy
Assortiment NP No 5100sO6 formes, 3 grains différents
− Les grains de tailles différentes des particu-les de diamant composant l’assor-timent sont signalés à l’aide d’anneaux colorés
− Ces divers grains permettent un usinage opti-mal, allant du dégrossissage à la finition, de tous les alliages nP
− Les formes différentes permettent d’usiner tout aussi bien les zones les plus menues que de larges surfaces
− La liaison carbure garantit une grande durée de vie quel que soit l’alliage usineé
Technische Details− Drehzahlempfehlung für alle nE-Metalle &
Keramiken – unbedingt drucklos arbeiten− max. 25.000 upm− zur Erhaltung der Schleifleistung ist der Sin-
terdiamant immer mit dem Reinigungsstein no 9920 abzuziehen
Technical Details− speed recommendation on all nP alloys and
ceramics - pressure-free application impera-tive
− 25.000 rpm max.− always use a dressing stone to retain cutting properties of sintered diamonds - fig.
no 9920 refers
Détails techniques− Vitesses de rotation conseillées pour tous
les métaux nP et les céramiques - travaillez toujours en n’exerçant aucune pression
− Max. 25’000 trs/min.− Pour conserver son pouvoir abrasif, l’instru-
ment diamanté par frittage doit toujours être passé sur une pierre de nettoyage - voir fig.
no 9920
Sintered Diamonds
3698
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
L mm 2,5 10,0 10,0 10,0 8,0 6,0 4,0 2,0 1,5Grösse/Size/Taille 1/10 mm 037 037 037 037 037 016 018 031 027Order No. ● 5002HP ● 5005HP ● 5008HP ● 5009HP ● 5022HP ● 5023HP ● 5024HP ● 5025HP ● 5026HPISO No. 807 104... 012 513 037 112 513 037 250 513 037 172 513 037 161 513 037 248 513 016 110 513 018 023 513 031 023 513 027
50FeinFineFine
d 20.000 - 25.000p 1
L mm 2,0 3,0 10,0 4,0Grösse/Size/Taille 1/10 mm 022 020 037 050Order No. ● 5027HP ● 5028HP ● 5029HP ● 5030HPISO No. 807 104... 023 513 022 488 513 020 225 513 037 030 513 050
50FeinFineFine
d 20.000 - 25.000p 1
L mm 2,5 4,0 10,0 10,0 10,0 10,0 10,0Grösse/Size/Taille 1/10 mm 037 037 050 037 050 037 037 037Order No. 5101HP 5102HP 5103HP 5105HP 5106HP 5107HP 5108HP 5109HPISO No. 807 104... 001 523 037 012 523 037 013 523 050 112 523 037 112 523 050 142 523 037 250 523 037 172 523 037
51Standard
d 20.000 - 25.000p 1
L mm 0,5 8,0 9,0 10,0 5,0 12,0 12,0 6,0Grösse/Size/Taille 1/10 mm 080 023 023 037 080 050 050 016Order No. 5114RA 5115HP 5117HP 5118HP 5119HP 5120HP 5121HP 5123HPISO No. 807 104... 161 523 023 141 523 023 199 523 037 030 523 080 274 523 050 143 523 050 272 523 016ISO No. 807 204... 370 523 080
51Standard
d 20.000 - 25.000p 1
L mm 10,0 10,0 0,6 0,6 0,25Grösse/Size/Taille 1/10 mm 050 050 080 220 220Order No. 5110HP 5111HP 5112HP 5113HP 5122HPISO No. 807 104... 174 523 050 199 523 050 370 523 080 345 523 220 345 523 220
dmax. 20.000 20.000
51Standard
d 20.000 - 25.000p 1
50Fine
↻ 20.000 - 25.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
50Fine
↻ 20.000 - 25.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
51Standard
↻ 20.000 - 25.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
51Standard
↻ 20.000 - 25.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
51Standard
↻ 20.000 - 25.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
Sintered Diamonds
L mm 2,5 10,0 10,0 10,0 8,0 6,0 4,0 2,0 1,5
1/10 mm • 037 • 037 • 037 • 037 • 037 • 016 • 018 • 031 • 027
Order No. SET573 SET574 SET575 SET576 SET577 SET578 SET579 SET580 SET581
L mm 2,0 3,0 10,0 4,0
1/10 mm • 022 • 020 • 037 • 050
Order No. SET582 SET583 SET584 SET585
L mm 2,5 4,0 10,0 10,0 10,0 10,0 10,0
1/10 mm 037 037 050 037 050 037 037 037
Order No. SET586 SET587 SET588 SET590 SET591 SET592 SET593 SET594
L mm 0,5 8,0 9,0 10,0 5,0 12,0 12,0 6,0
1/10 mm 080 023 023 037 080 050 050 016
Order No. SET599 SET600 SET602 SET603 SET604 SET605 SET606 SET1310
L mm 10,0 10,0 0,6 0,6 0,25
1/10 mm 050 050 080 220 220
Order No. SET595 SET596 SET597 SET598 SET607↻max. 20,000 20,000
37 99
sINTer DIAMANTeN • sINTereD DIAMONDs • INsTruMeNTs DIAMATés pAr frITTAge
L mm 10,0 10,0 10,0 10,0 10,0 10,0Grösse/Size/Taille 1/10 mm 037 050 037 037 050 037Order No. ● 5205HP ● 5206HP ● 5208HP ● 5209HP ● 5211HP ● 5218HPISO No. 807 104... 112 542 037 112 542 050 250 542 037 172 542 037 199 542 050 199 542 037
52GrobCoarseGros
d 20.000 - 25.000p 1
L mm 12,0 12,0Grösse/Size/Taille 1/10 mm 050 050Order No. ● 5331HP ● 5332HPISO No. 807 104... 274 543 050 143 543 050
53SupergrobSuper-coarseSuper-gros
d 20.000 - 25.000p 1
DsB 321
p 1
L
L mm 0,30 0,30Size 1/10 mm 300 400Order No. DSB321.524.300HP DSB321.524.400HPISO No. 807 104... 321 524 300 321 524 400
dmax. 10.000 10.000
sINTer DIAMANTscheIBeRandgesinterte Gips Diamantscheibe für Säge-stümpfe zum Trennen von Zahnkränzen bei Gipsmodellen
sINTereD DIAMOND DIscPlaster diamond disc with sintered rim for dies, tooth arch separation on plaster models
DIsQue DIAMANTé DANs lA MAsseDisque diamanté pour plâtre, avec bord diamanté dans la masse, pour dies, pour la séparation des arcades dentaires dans les modèles en plâtre
L
51225113
p 1
L
L mm 0,25 0,6Size 1/10 mm 220 220Order No. 5122HP 5113HPISO No. 807 104... 345 523 220 345 523 220
dmax. 20.000 20.000
sINTer DIAMANTscheIBeFür Keramik, Edelmetalle, Chrom-Kobalt, Abtren-nen von Gusskanälen
sINTereD DIAMOND DIscfor ceramics, precious metals, chrome-cobalt alloys, cutting of sprues
DIsQue DIAMANTé DANs lA MAssePour céramique, métaux précieux et chrome-cobalt, pour tronçonner les tiges de coulées
52Coarse
↻ 20.000 - 25.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
53Super-Coarse
↻ 20.000 - 25.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
51225133
DSB 321
Sintered Diamonds
L mm 10,0 10,0 10,0 10,0 10,0 10,0
1/10 mm • 037 • 050 • 037 • 037 • 050 • 037
Order No. SET608 SET609 SET610 SET611 SET612 SET613
L mm 12,0 12,0
1/10 mm • 050 • 050
Order No. SET614 SET615
L mm 0,25 0,6
1/10 mm 220 220
Order No. SET607 SET598↻max. 20,000 20,000
L mm 0,30 0,30
1/10 mm 300 400
Order No. SET637 SET638↻max. 10,000 10,000
SKILLDENTA PRICES EXCLUDE VAT & CARRIAGE, VALID FROM 31/05/2016. SUBJECT TO AVAILABILITY - E & OE. IMAGES ARE NOT TO SCALE
CALL US ON
01494 448474
FOR PRICES
3889
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.09089
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.090 89
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.090
89
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.090
490Hollow Grinder
↻ 10.000 - 15.000 1
89
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.090
DIACRYLIC Grinder
↻ 15.000 1
89
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.090
DUO DIACRYLIC Grinder
↻ 15.000 1
89
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.090
Hollow Diamond GrinderIdeal for removing large areas of acrylic with its high cutting capacity and minimum heat generation.
For pretrimming orthodontic and denture acrylics and preparing customised impressi-on trays and soft denture liners.
Instructions for use:Use only minimum pressure when preparing. Adhere to the recommended rpm.
DIACRYLIC GrinderMultifunctional diamond rotary instrument for rapid, accurate preparation of denture acry-lics.
The special head designs are suitable for preparing sublingual rolls, papilla contours, denture peripheries as well as labial and buc-cal frena.
DIACRYLIC Grinder SetFor rapid, accurate preparation of orthodontic and denture acrylics as well as customised impression trays and soft denture liners.
For removing irregularities on the fitting sur-faces of dentures and preparing slender labi-al and buccal frena.
DUO DIACRYLIC GrinderFor pretrimming orthodontic and denture acrylics and preparing customised impressi-on trays and soft denture liners.
Special diamond coating with chip removal channels ensures removal of large areas of acrylic with maximum cutting capacity and minimum heat generation.
DUO DIACRYLIC Grinder SetSpecial diamond coating with chip removal channels ensures removal of large areas of acrylic with maximum cutting capacity and minimum heat generation for a high-quality surface finish.
Ideal for rapid, accurate preparation.
Diamond Grinder
L mm 20,0 20,0
Size 1/10 mm 090 110
Order No. SET559 SET560Shank: HP
L mm 10,0 15,0 15,0 18,0 9,0
Size 1/10 mm 065 065 075 055 055
Order No. SET553 SET554 SET555 SET556 SET557Shank: HP
L mm 15,0 13,0 17,0 6.5 19,0 14,0
Size 1/10 mm 085 085 090 060 065 065
Order No. SET549 SET546 SET547 SET548 SET550 SET551Shank: HP
39
SET561SET570
12,016,0085085
F SET562
19,0065
F SET563075
F SET564
12,0075
F SET565
12,0065
F SET566
10,0055
F SET567
10,0055
F SET568 104 HP
Order No. standard Order No. fine
Shank
RUBYNIT
standard fine
Size
Size
1/10 mm L mm
L mm
13,0050 033
F
8,0
SET569 104 HP
Order No. standard Order No. fine
Shank
standard fine
SET561
Smooth grinding of palatinal denture surfaces
SET571
10,0040
SET572
£6.60 £6.60 £6.60 £6.60 £6.60 £6.60 £6.60 £6.60
£6.60 £5.48 £5.48
SET561SET570
12,016,0085085
F SET562
19,0065
F SET563075
F SET564
12,0075
F SET565
12,0065
F SET566
10,0055
F SET567
10,0055
F SET568 104 HP
Order No. standard Order No. fine
Shank
RUBYNIT
standard fine
Size
Size
1/10 mm L mm
L mm
13,0050 033
F
8,0
SET569 104 HP
Order No. standard Order No. fine
Shank
standard fine
SET561
Smooth grinding of palatinal denture surfaces
SET571
10,0040
SET572
£6.60 £6.60 £6.60 £6.60 £6.60 £6.60 £6.60 £6.60
£6.60 £5.48 £5.48
89
DIAMANT TrIMMer • DIAMoND grINDer • frAIses DIAMANTees
L mm 18,0 20,0Size 1/10 mm 090 110
Shank Order No. 490.104.090 490.104.110HP ISO No. 806 104... 490 544 090 490 544 110
490Hohlschleifer • Hollow Grinder •Instrument Creux
d 10.000 - 15.000p 1
490.104.090
L mm 10,0 15,0 15,0 18,0 9,0Size 1/10 mm 065 065 075 055 055
Shank Order No. DG410.104.065 DG420.104.065 DG430.104.075 DG440.104.055 DG450.104.055HP ISO No. 806 104... 410 544 065 420 544 065 430 544 075 440 544 055 450 544 055
DIACRYLIC Grinder
d 15.000p 1
L mm 15,0 13,0 17,0 6,5 19,0 14,0Size 1/10 mm 085 085 090 060 065 065
Shank Order No. DDG860.104.085 DDG369.104.085 DDG405.104.090 DDG840.104.060 DDG893.104.065 DDG894.104.065HP ISO No. 806 104... 860 544 085 369 544 085 405 544 090 840 544 060 893 544 065 894 544 065
DUO DIACRYLIC Grinder
d 15.000p 1
Duo Diacrylic Grinder Set No. DDG800SO
DIACRYLIC Grinder Set No. DG400SO
DG420.104.065
DG410.104.065
DDG894.104.065
DG450.104.055
DD405.104.090
SET561SET570
12,016,0085085
F SET562
19,0065
F SET563075
F SET564
12,0075
F SET565
12,0065
F SET566
10,0055
F SET567
10,0055
F SET568 104 HP
Order No. standard Order No. fine
Shank
RUBYNIT
standard fine
Size
Size
1/10 mm L mm
L mm
13,0050 033
F
8,0
SET569 104 HP
Order No. standard Order No. fine
Shank
standard fine
SET561
Smooth grinding of palatinal denture surfaces
SET571
10,0040
SET572
£6.60 £6.60 £6.60 £6.60 £6.60 £6.60 £6.60 £6.60
£6.60 £5.48 £5.48
Rubynit
L mm 16,0 12,0 19,0 12,0 12,0 10,0 10,0
Size 1/10 mm 085 085 065 075 075 065 055 055
Standard Order No. Standard SET561 SET562 SET563 SET564 SET565 SET566 SET567 SET568Fine Order No. Fine SET570 – – – – – – –
L mm 13,0 8,0 10,0
Size 1/10 mm 050 033 040
Standard Order No. Standard SET569 – –Fine Order No. Fine – SET571 SET572
40102
L mm 3,0 3,5 6,0 1,0Shank Size 1/10 140 180 180 220
HP Order No. 9001.140HP 9002.180HP 9003.180HP 9004.220HP• ↻ opt. 3.000 • G9002.180HP
SuperMax
↻ 15.000p 1
• green ring coarse
supermax
Sintered diamond with organic bonder, for grinding of ceramics and metals, enables rough trimming without heat build - up in the restoration. Suitable for rough trimming and pressable porcelain sprues.
Pressure - free application imperative.
Porcelain- / Pressable porcelain- / All - porcelain restorations, zrO²For rough trimming (SuperMax) and initial contouring (CeraPro) without heat build - up
Advantages
- cool, vibration-free cutting and therefore lowsurface temperature without streak formati-on
- highly efficient abrasive properties, self-cleansing, self-sharpening, low dust genera-tion
- distinct time saving caused by reducedrework results in an unsurpassed price-per-formance-ratio
Application
- ceramics, all porcelain, ZrO²- porcelain-fused alloys- chrome-cobalt-alloys- titanium- gold and all types of soft alloys
L mm 18,0 3,5 2,5 1,5Shank Size 1/10 060 220 220 220
HP Order No. 9005.060HP 9006.220HP 9007.220HP 9009.220HP
SuperMax
↻ 15.000p 1
cerAPrO Abrasive trimmer with natural diamond grit. Ideal for initial contouring and preparing without heat build in the restoration. Suitable for preparing larger vestibular and oral sur-faces.
CeraProd opt. 12.000d 10.000 - 15.000d 5.000 *p 1
L mm 13,0 11,0 3,0 7,0 7,0 2,0 8,0Size 1/10 mm 050 040 150 120 035 050 040Order No. 8001.050HP 8002.040HP 8003.150HP 8004.120HP 8005.035HP 8006.050HP 8007.040HPISO No. 805 104... 107 524 050 173 524 040 372 524 150 024 524 120 248 524 035 010 524 050 198 524 040Order No. • G8001.050HP • G8002.040HPISO No. 805 104... 107 534 050 173 534 040
d 5.000● Grüner Ring grob / green ring coarse / bague verte gros grain
* *
ceraTec
For preparing high-performance zirconia with very high degrees of hardness >900 MPa. shapes, ball and torpedo:The ball shape is used for preparing occlusal surfaces and guarantees an optimal view of the trimming surface during preparation. The torpedo shape can be used for finishing even difficult interproximal spaces with bridges and complicated, undulating preparation margins.
CeraTecd opt. 10.000d 10.000 - 12.000d opt. 5.000 *p 1
L mm 11,0 7,0 2,0 8,0 11,0 4,0 2,0Size 1/10 mm 040 035 050 040 035 040 220Order No. 952.040HP 955.035HP 956.050HP 957.040HP 958.035HP 959.040HP 960.220HPISO No. 805 104... 173 514 040 248 514 035 010 514 050 198 514 040 161 514 035 001 514 040 303 514 220
*
ceraTec ApplicationPressable-ceramic for fabricating inlays, onlays, veneers and single crowns.Pressable-ceramic for overpressing alloys. Metal-ceramics: High or low-fusingPorcelain for veneering dental alloys.
SuperMax
↻ 15.000
1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
SuperMax
↻ 15.000
1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
SuperMax
CERAPRO
CeraTec
CeraTec↻ opt 10.000↻ opt 10.000 - 12.000↻ opt 5.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
CeraPro↻ opt 12.000↻ opt 10.000 - 15.000↻ opt 5.000 1
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
80
hP DIAMANTeN • hP DIAMONDs • DIAMANTs PM
801.104.023
L mmShank ISO Order No. HP 806 104 001 524... 801.104... 009 010 012 014 016 018 021 023 029 035
• 806 104 001 534... 6801.104... 035
801
KugelRoundBoule
p 3
L mm 1,5 1,5 1,5 1,5 2,0 2,0 1,5 2,0Shank ISO Order No. HP 806 104 010 524... 805.104... 012 014 016 018 021 023 040 050
805
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 3,5Shank ISO Order No. HP 806 104 019 524... 809.104... 023
809
Umgekehrter Kegel mit AnsatzInverted Cone with CollarCône renversé avec col
p 3
L mm 4,0 5,0 6,0Shank ISO Order No. HP 806 104 225 524... 807.104... 016 018 023
807
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 0,7 0,8Shank ISO Order No. HP 806 104 014 524... 808.104... 018 023
808
Umgekehrter KegelInverted ConeCône renversé
p 3
L mm 1,5 2,0Shank ISO Order No. HP 806 104 022 524... 812.104... 025 050
812
Umgekehrter Kegel, seitenbelegtInverted Cone, side-coatedCône renversé, diamanté sur les faces travaillantes
p 3
L mm 1,0Shank ISO Order No. HP 806 104 041 524... 818.104... 033
818
RadWheelRoue
p 3
L mm 0,8 0,9 1,1 1,5Shank ISO Order No. HP 806 104 304 524... 825.104... 018 025 040 050
825
LinseKnife EdgeLentille
p 3
87
WhITe TIger DIAMANTeN • DIAMONDs WhITe TIger • DIAMANTs WhITe TIger
für Laborturbine mit Wasserkühlungfor laboratory turbine with water coolingpour turbine de laboratoir avec refroidissment de l’eau
● Blauer Ring standard • blue ring standard • bague bleue standard – 126μm ISO No. 524 ● Roter Ring fein • red ring fine • bague rouge grain fin – 40μm ISO No. 514 ● Grüner Ring grob • green ring coarse • bague verte gros grain – 151μm ISO No. 534
Shank L mm 5,5 5,0ISO Order No.
FG • W806 314 257 524... W 368.314... 020• W806 314 257 514... FW 368.314... 020• W806 314 257 534... GW 368.314... 020 023
W368KnospePointed BudBouton
p 3 d opt. 160.000
Shank L mm ISO Order No.
FG • W806 314 001 524... W 801.314... 014 021 023• W806 314 001 514... FW 801.314... 014 021• W806 314 001 534... GW 801.314... 014 021 023
W801KugelRoundBoule
p 3 d opt. 160.000
W846KRKonus Kante rundRound Edge TaperCône, bord arrondi
p 3 d opt. 160.000
Shank L mm 6,0 6,0ISO Order No.
FG • W806 314 545 524... W 846KR.314... 016 023
Shank L mm 8,0 8,0ISO Order No.
FG • W806 314 141 524... W 881.314... 014• W806 314 141 514... FW 881.314... 014• W806 314 141 534... GW 881.314... 014 016
W881Zylinder rundRound End CylinderCylindre, bout arrondi
p 3 d opt. 160.000
Shank L mm 4,2ISO Order No.
FG • W806 314 277 524... W 379.314... 023• W806 314 277 514... FW 379.314... 023• W806 314 277 534... GW 379.314... 023
W379EiformEgg Shape / FootballBouton
p 3 d opt. 160.000
Shank L mm 4,0 5,0 5,0ISO Order No.
FG • W806 314 239 524... W 830L.314... 012 014 016• W806 314 239 514... FW 830L.314... 012 014 016• W806 314 239 534... GW 830L.314... 012 014 016
W830LBirne langPear longPoire, long
p 3 d opt. 160.000
W863FlammeFlameFlamme
p 3 d opt. 160.000
Shank L mm 10,0 10,0ISO Order No.
FG • W806 314 250 524... W 863.314... 012 016• W806 314 250 514... FW 863.314... 012 016• W806 314 250 534... GW 863.314... 012 016
W879KTorpedo konischTorpedo taperedCône allongé, à biseau
p 3 d opt. 160.000
Shank L mm 10,0 10,0 10,0 10,0ISO Order No.
FG • W806 314 299 524... W 879K.314... 012 014 016 018• W806 314 299 514... FW 879K.314... 012 014 016 018• W806 314 299 534... GW 879K.314... 012 014 016 018
Shank L mm 8,0 8,0 8,0 8,0 8,0ISO Order No.
FG • W806 314 298 524... W 878K.314... 014 016 018 020 022• W806 314 298 514... FW 878K.314... 014 016 018 020 022• W806 314 298 534... GW 878K.314... 014 016 018 020 022
W878KTorpedo konischTorpedo taperedCône, allongé, à biseau
p 3 d opt. 160.000
SuperMax
L mm 3,0 3,5 6,0Shank Size 1/10 mm 140 180 180 220
Order No. SET620 SET621 SET622 SET623
L mm 18,0 3,5 2,5 1,5Shank Size 1/10 mm 060 220 220 220
Order No. SET624 SET625 SET626 SET805
L mm 13,0 11,0 3,0 7,0 7,0 2,0 8,0
Size 1/10 mm 060 220 220 220
Order No. SET631 SET632 SET633 SET634 SET776 SET775 SET443
Order No. Green Ring Coarse SET635 SET636 – – – – –*↻5.000 *↻5.000
L mm 11,0 7,0 2,0 8,0 11,0 4,0
Size 1/10 mm 040 035 050 040 035 040
Order No. SET799 SET800 SET801 SET802 SET796 SET804
102
L mm 3,0 3,5 6,0 1,0Shank Size 1/10 140 180 180 220
HP Order No. 9001.140HP 9002.180HP 9003.180HP 9004.220HP• ↻ opt. 3.000 • G9002.180HP
SuperMax
↻ 15.000p 1
• green ring coarse
supermax
Sintered diamond with organic bonder, for grinding of ceramics and metals, enables rough trimming without heat build - up in the restoration. Suitable for rough trimming and pressable porcelain sprues.
Pressure - free application imperative.
Porcelain- / Pressable porcelain- / All - porcelain restorations, zrO²For rough trimming (SuperMax) and initial contouring (CeraPro) without heat build - up
Advantages
- cool, vibration-free cutting and therefore lowsurface temperature without streak formati-on
- highly efficient abrasive properties, self-cleansing, self-sharpening, low dust genera-tion
- distinct time saving caused by reducedrework results in an unsurpassed price-per-formance-ratio
Application
- ceramics, all porcelain, ZrO²- porcelain-fused alloys- chrome-cobalt-alloys- titanium- gold and all types of soft alloys
L mm 18,0 3,5 2,5 1,5Shank Size 1/10 060 220 220 220
HP Order No. 9005.060HP 9006.220HP 9007.220HP 9009.220HP
SuperMax
↻ 15.000p 1
cerAPrO Abrasive trimmer with natural diamond grit. Ideal for initial contouring and preparing without heat build in the restoration. Suitable for preparing larger vestibular and oral sur-faces.
CeraProd opt. 12.000d 10.000 - 15.000d 5.000 *p 1
L mm 13,0 11,0 3,0 7,0 7,0 2,0 8,0Size 1/10 mm 050 040 150 120 035 050 040Order No. 8001.050HP 8002.040HP 8003.150HP 8004.120HP 8005.035HP 8006.050HP 8007.040HPISO No. 805 104... 107 524 050 173 524 040 372 524 150 024 524 120 248 524 035 010 524 050 198 524 040Order No. • G8001.050HP • G8002.040HPISO No. 805 104... 107 534 050 173 534 040
d 5.000● Grüner Ring grob / green ring coarse / bague verte gros grain
* *
ceraTec
For preparing high-performance zirconia with very high degrees of hardness >900 MPa. shapes, ball and torpedo:The ball shape is used for preparing occlusal surfaces and guarantees an optimal view of the trimming surface during preparation. The torpedo shape can be used for finishing even difficult interproximal spaces with bridges and complicated, undulating preparation margins.
CeraTecd opt. 10.000d 10.000 - 12.000d opt. 5.000 *p 1
L mm 11,0 7,0 2,0 8,0 11,0 4,0 2,0Size 1/10 mm 040 035 050 040 035 040 220Order No. 952.040HP 955.035HP 956.050HP 957.040HP 958.035HP 959.040HP 960.220HPISO No. 805 104... 173 514 040 248 514 035 010 514 050 198 514 040 161 514 035 001 514 040 303 514 220
*
ceraTec ApplicationPressable-ceramic for fabricating inlays, onlays, veneers and single crowns.Pressable-ceramic for overpressing alloys. Metal-ceramics: High or low-fusingPorcelain for veneering dental alloys.