Post on 16-Apr-2017
transcript
SmartPTT – Indoor Location for MOTOTRBO
2
Contents
What is Indoor Tracking?
Benefits
Characteristics
Requirements
Estimote Beacon Configuration
Radio Subscriber Configuration
SmartPTT Radioserver Configuration
SmartPTT Dispatch Client Configuration
3
What is Indoor Tracking
GPS is not available indoors, but location monitoring is often required in places such as:
Mines Airports Bus, Train, and Metro Stations Hospitals Hotels Stadiums School Campuses Museums Warehouses Shopping Malls
Positioning beacons work with the Bluetooth available in the new “e” series MOTOTRBO radios.
4
iBeacon Transmission Sequence
5
Benefits
Employee Safety - In case of an emergency, you will know the location of your employees. This helps minimize response times that could save lives.
Employee Accountability - With an advanced system of rules and alerts, it is possible to configure the route for the patrol of buildings and premises, notifying the dispatcher if there is any deviation from the route.
Easy implementation - data from beacons is transmitted over the radio channel, so no network infrastructure is needed. This ensures a simple and low-cost implementation.
Independent Operation - Proximity beacons operate on batteries, requiring replacement only once every 2 to 3 years depending on configuration.
6
Characteristics
Real-time indoor tracking system for MOTOTRBO subscribers.
Show subscriber movements on 2D (JPEG, PNG, BMP) or 3D (DWG, DXF) maps.
Change easily from one floor to another, in the case of multi-level buildings.
Animation of the route of a subscriber.
Guard patrol route control.
Geo-fences with configurable alarms.
Support for Lone Workers.
7
Required Equipment
8
Required Equipment
• Indoor Positioning option enabled in the SmartPTT license
key
• New generation MOTOTRBO radios, announced in Q1
2016 (“e”-series). The radios should be Bluetooth equipped
and Indoor Tracking support should be enabled.
• Off-the-shelf Bluetooth iBeacons (i.e. Estimote Proximity
Beacons)
9
Estimote Beacon Configuration
10
iBeacons Estimote Configuration
When having multiple beacons to configure, it is necessary to isolate the beacons to know which one is to be configured.
The screens show two ways of identifying the closest beacons.
The iOS app also has a filter to select the closest beacon.
11
iBeacons Estimote Configuration
Name: Configure a unique alias for each beacon (i.e. Room 102)
Owner: The email address of the registered owner of the beacon
AndroidiOS
12
iBeacons Estimote Configuration
UUID is the Universally Unique Identifier andconsists of 32 hexadecimal characters in 5groups (must follow 8-4-4-4-12 format)
Major and Minor IDs can be set to a valuebetween 0 and 65535
Transmit Power (Tx) sets the coverage areaof the beacon
Advertising Interval sets how frequently thebeacon transmits its ID
Remaining Battery Life reflects the currentbattery life based on the Transmit Power andAdvertising interval settings (1-3 years)
AndroidiOS
13
iBeacons Estimote Configuration
Transmission Power (Tx)
The Broadcasting Power sets the transmission rangeof the beacon.
The coverage area (diameter) at Low power is 1 ft.(0.25 m) and at High power is 230 ft. (70 m).
AndroidiOS
14
iBeacons Estimote Configuration
Advertising Interval
The Advertising Interval sets how frequentlythe beacon transmits its ID.
Current Interval shows the time inmilliseconds from a range of 100 msec to10,000 msec.
AndroidiOS
15
MOTOTRBO Radio Configuration
16
Radio Subscriber Configuration
The Subscriber firmware version must be 2.6 or higher.
The Indoor Location Tracking license must be present in the radio.
17
Radio Subscriber Configuration
In the MENU page, check on Indoor Location.
18
Radio Subscriber Configuration
In the Network page, Bluetooth must be enabled.
In Indoor Location enable and add the UUIDs of the Beacons. Reference Slide 12.
19
SmartPTT Radioserver Configuration
20
SmartPTT Radioserver Configuration
Check on the Active check box on the
Indoor Tracking page
Indoor Source: Select the type of
Beacon that will be used.
Minimum RSSI: Received RSSI levels
below this setting will be ignored.
Set List of allowed Beacons: In
areas with other beacons, this list can
limit which beacons the software will
consider valid.
21
SmartPTT Dispatch Client Configuration
22
Dispatcher Configuration
Click Map in the Navigation bar, then
Indoor Tracking, then New.
Navigate to the location with your
floorplan, select the floorplan and click
Open.
In the Beacon Properties box enter the
Beacon Major and Minor IDs (separated
by a period) and the Beacon Name.
Select OK and then place the beacon on
the map in the desired location.
Repeat this until all beacons have been
placed and then click Save As, which
saves the file in an splanx format for use
in SmartPTT.
23
Floor Plan Options
Geofences: This enables the creation of zones of beacons that
are considered an area of interest (i.e. work area, hazardous area)
Routes: If a worker should follow a predetermined route, this sets
the order of the route.
24
Options of the Indoor Tracking Plane
Subscribers on Indoor Map: Specifies which subscriber or subscribers will be displayed on the indoor map.
Subscribers’ Tracks: Enables the dispatcher to run a track animation for a subscriber. Click “Add Track”
Select the desired Subscriber
Specify the time period
Click OK
25
Your Business is Important to Us.
Thank You!
Michael SoulliardWestern North America Sales
786-923-1401michael@smartptt.com
Terry LangEastern North America Sales
786-923-1404terry@smartptt.com
Find us on: