Post on 17-Jun-2020
transcript
Design of a net-zero energy
community: Waalwijk
Smitha Sundaram
-2-
Master of Science Thesis EGI-2013-069MSC
EKV963
Design of a net-zero energy community:
Waalwijk
Smitha Sundaram
Approved
Date
Examiner
Torsten Fransson
Supervisor
Amir Vadiei
Local supervisor
Anna Provoost
Commissioner
Contact person
Abstract
The European Union has passed a number of important energy-related resolutions in the past few years; the most important ones being the ‘Energy Performance of Buildings’ Directive (2010) and the ‘Renewable Energy Roadmap for 2020’ (2007). These saw the member states, including the Netherlands, implementing stringent regulations in order to achieve these ambitious goals. In the light of these developments, the onus is on municipalities to initiate and promote projects that address these challenges. Thus, this project is an initiative by the municipality of Waalwijk, along with Casade (a corporation responsible for social housing). The basic goal of this project is to study the energy consumption of Waalwijk, and try to make it a net- zero energy community, while ensuring that the suggestions are practical, socially acceptable and of course, financially viable. In order to do so, the principle of ‘Trias Energetica’ is adopted – that is, reduce the energy consumption as far as possible, supply the reduced energy demand using renewable energy and thirdly, if there is any demand still to be met, supply it by using fossil fuels as efficiently as possible. Firstly, a zone was selected at the centre of the city, to include as many different types of dwellings as possible (based on age and ownership – rented/private/public). Accordingly, a theatre, an office, an apartment building, individual houses built in the 1980s (22 in number) and in the 1940s (130 in number) were taken into consideration. Next, the energy consumption of this zone was determined. This involved approaching the residents with a questionnaire, and collecting data regarding their energy consumption, heating systems, lighting profiles, and so on. Based on the data collected, (and taking averages) the annual energy consumption of the zone was calculated to be 952.8 MWh of electricity and 331,231 m3 of gas. Next, following the Trias Energetica, ways to reduce energy consumption were studied - without making major changes to the structure of the houses. The measures included lighting retrofits, insulation of houses and window retrofits. Based on these suggestions, the annual reduction in electricity for the zone is calculated as 55 MWh and for gas as 105,586 m3. This brings down the annual consumption to 902 MWh of electricity and 225,645 m3 of gas respectively. Ways to supply this energy demand were evaluated, and narrowed down to solar PV and heat pumps. Solar PV for individual houses, the apartment building and the theatre were calculated, and the total
-3-
generation due to solar PV in the zone comes to about 237,472 MWh of electricity. This is 26% of the annual electricity consumption of the zone. Heat pumps were also investigated for the dwellings. Air source heat pumps were evaluated for the houses and the apartment building, while a ground-source heat pump was studied for the theatre. It is found that the heat pumps can supply most of the gas demand of the zone, at the expense of additional electricity usage. This was followed by a financial analysis of the proposed solutions, using basic tools like simple payback, net present value (NPV) and internal rate of return (IRR). Based on the results, it is found that the insulation and window retrofits are highly profitable, contribute considerably to energy savings and pay themselves out within 8 years. The solar PV is also quite cost-effective, and has a maximum payback of 13 years. Heat pumps for the old houses are not as cost-effective (after insulation); since the savings accrued due to reduction in gas consumption is off-set by the additional electricity consumption. That being said, heat pumps require detailed and customized calculations, since their performance is highly specific to the dwelling. A more detailed study of the sizing and installation of heat pumps can lead to improved performance and increase the cost-effectiveness of this technology. Lastly, a brief overview of financial models popularly used for renewable energy projects is presented, with examples. In order to address general problems encountered in such projects, as well as those specific to Waalwijk - such as spilt incentive (due to social housing), public buildings, high upfront cost, lack of awareness and technical know-how – a financial model is suggested for Waalwijk. This is based on the concept of an ESCo (Energy Services Company), to which the project will be sub-contracted from start to finish, for a certain fixed price. The ESCo might even be able to arrange for financing, or the municipality could be the guarantor for the project. In conclusion, based on the above study in a pilot zone, we see that insulation, window and lighting retrofits alone can contribute measurably to energy-efficiency in Waalwijk. Further, Waalwijk could become an almost net-zero energy community as far as gas consumption is concerned. However, electricity generation from renewable sources falls rather short of supplying the entire demand (only 28% can be supplied). This requires other, more centralized options such as wind energy, waste-to-energy, or de-centralized technologies like micro-CHPs and fuel cells, which are yet to become economically viable for small, residential applications. Moreover, energy savings can be increased by catalyzing a change in the behavioural aspect of citizens (who are mostly observed to be above the age of 60, and for whom energy efficiency is not a priority). This requires spreading more awareness by conducting regular meetings with the locals and educating them about the importance of energy savings. This is extremely essential in order to transform a community into a net-zero energy one.
-4-
Acknowledgement
This thesis is in partial fulfillment of my MSc. in Environomical Pathways for Sustainable Energy Systems
(MSc. SELECT) at the Royal Institute of Technology (KTH), Stockholm and the Eindhoven University
of Technology (TU/e) – 2011-2013.
I would like to take this opportunity to extend my gratitude to Mr. Rob Barnhoorn, my technical
supervisor at Stichting KIEN, for his constant guidance, motivation and support throughout this project.
I would also like to personally thank my colleagues at Stichting KIEN – Mr. Adrie van Duijne, Ms. Anna
Provoost and Mr. Koos Kerstholt, for a wonderful working environment and providing me with
assistance in technical as well as administrative issues. In addition, I’d like to thank Mr. Albert Pols, who
initiated this project, along with Stichting KIEN.
I am grateful to Mr. Titus Drijkoningen (Gementee Waalwijk) and Mr. Joost Huijbregts (Casade) for all
their assistance in defining the aims of the project, and also, for helping me obtain as much data, as was
possible. A special thanks to Ms. Margriet Rinja (Gementee Waalwijk), for patiently getting in touch with
the residents, and requesting them to provide information. I would also like to thank Ms. Linda
Dumpleton (Gementee Waalwijk), who kindly agreed to act as my translator during the house visits. I am
also grateful to the residents of Waalwijk who agreed to meet with me and share data.
I would like to express my heartiest thanks to my supervisor, Dr. Amir Vadiei and Course Director, Dr.
Thomas Nordgreen for their valuable inputs during the course of this project.
Finally, my sincerest thanks to my family members for their unwavering support, encouragement and
blessings; I am also immensely grateful to my friend Ramesh Prateek Raju Arumugam, for his invaluable
inputs and keeping my morale up all through this project.
My finest wishes, thank you.
Eindhoven, 2013
-5-
Table of Contents
Abstract ........................................................................................................................................................................... 2
1 Introduction .......................................................................................................................................................... 8
1.1 What is a net-zero energy community? .......................................................................................................... 8
1.2 Waalwijk: an overview ....................................................................................................................................... 8
1.3 Project description and goals ........................................................................................................................... 9
2 Methodology ....................................................................................................................................................... 12
2.1 Trias Energetica ......................................................................................................................................... 12
2.2 Project execution plan .............................................................................................................................. 12
3 Selection of zone and data gathering .............................................................................................................. 13
3.1 Types of buildings covered ...................................................................................................................... 13
3.2 Visiting houses ........................................................................................................................................... 16
3.3 Brief description of houses visited ......................................................................................................... 16
3.4 Observations .............................................................................................................................................. 18
4 Energy consumption of the zone .................................................................................................................... 19
5 Reduction of energy consumption .................................................................................................................. 20
5.1 Lighting retrofits ....................................................................................................................................... 20
5.2 Window retrofits ....................................................................................................................................... 23
5.3 Insulation .................................................................................................................................................... 24
5.4 Total reduction in energy consumption for the zone ......................................................................... 26
6 Energy supply possibilities ................................................................................................................................ 27
6.1 Solar PV ...................................................................................................................................................... 27
6.1.1 Brief working of a solar panel: ....................................................................................................... 28
6.1.2 Types of solar PV configurations .................................................................................................. 28
6.1.3 Designing the solar PV systems for buildings in Waalwijk ....................................................... 29
6.2 Heat pumps ................................................................................................................................................ 35
6.2.1 Working and efficiency of a heat pump ....................................................................................... 36
6.2.2 Types of heat pumps ....................................................................................................................... 37
6.2.3 Heat pumps in Waalwijk ................................................................................................................. 38
7 Financial analysis ................................................................................................................................................ 43
7.1 Methods used to calculate profitability .................................................................................................. 43
7.2 Subsidies ..................................................................................................................................................... 43
7.3 Analysis of the proposed measures ........................................................................................................ 44
8 Financial models ................................................................................................................................................. 46
8.1 Barriers to implementation of RETs ..................................................................................................... 46
8.2 Types of financial models ........................................................................................................................ 47
8.2.1 Integrated Energy Contracting Company (ESCo - IEC): ......................................................... 47
-6-
8.2.2 Loans and mortgages: ...................................................................................................................... 51
8.2.3 Leasing: .............................................................................................................................................. 52
8.2.4 On-bill financing .............................................................................................................................. 55
8.2.5 The proposed financial model for Waalwijk ............................................................................... 56
9 Challenges and future work .............................................................................................................................. 58
10 Conclusion ........................................................................................................................................................... 59
Works Cited .................................................................................................................................................................. 61
Appendix A: List of questions presented for data gathering .............................................................................................. 64
Appendix B: Savings due to lighting retrofits .................................................................................................................... 65
Appendix C: Savings due to window retrofits and insulation ............................................................................................ 68
Appendix D: Solar PV output and inverters selected for houses ....................................................................................... 70
Appendix E: Quote from LENS B.V. for solar PV system on apartment and theatre ................................................... 72
Appendix F: Financial analysis ....................................................................................................................................... 75
List of figures
Figure 1. Location of Waalwijk (source: Google Maps) ......................................................................................... 8
Figure 2. ‘Waalwijk centrum met stadhuis’ (Source: Panaromia)........................................................................... 8
Figure 3. Temperature data for Waalwijk, Netherlands (Source: Norwegian Meteorological Institute)........ 9
Figure 4. Average days with precipitation - Waalwijk, Netherlands (Source: Norwegian Meteorological
Institute) ..................................................................................................................................................... 9
Figure 5. Trias Energetica .......................................................................................................................................... 12
Figure 6. The extent of Waalwijk (Source: Google Maps) .................................................................................... 13
Figure 7. The selected zone (Source: Google Maps) ............................................................................................. 13
Figure 8. The bus station Vredesplein ..................................................................................................................... 14
Figure 9. Engelsestraat ................................................................................................................................................ 14
Figure 10. Towerij ....................................................................................................................................................... 14
Figure 11. Apartment building - Vredesstaete ........................................................................................................ 15
Figure 12. Commercial building on Vredesplein .................................................................................................... 15
Figure 13. De Leest ..................................................................................................................................................... 15
Figure 14. A comparison of power consumed by various kinds of lamps ......................................................... 20
Figure 15. Gas savings for various types of window glazing ............................................................................... 24
Figure 16. Different ways in which heat is lost from a house, and where isolation is carried out ................. 25
Figure 17. List of commercially available insulation materials (Source: Irish Energy Centre) ........................ 25
Figure 18. Setup of a stand-alone rooftop PV system ........................................................................................... 27
Figure 19. Working of a solar cell (Source: Mariadriana Creatore, Eindhoven University of Technology) . 28
Figure 20. Wire sizing - an example ......................................................................................................................... 30
Figure 21. Total inverter sizing output - an example ............................................................................................. 31
Figure 22. Scheme for the apartments, with Herman ........................................................................................... 32
Figure 23. Scheme for the collective meter – sans Herman ................................................................................. 32
Figure 24. Layout of the roof of the apartment building ...................................................................................... 33
Figure 25. Schematic of PV system for the theatre ............................................................................................... 35
Figure 26. Working principle of a heat pump (Source: Save Your Energy) ...................................................... 36
Figure 27. Schematic working and installation of a GSHP ................................................................................. 39
Figure 28. Comparison of different ESCos (Source: Wurtenberger, Blely et al., 2012) ................................... 49
-7-
Figure 29. IEC - financing by client (Adapted from: Wurtenberger, Blely et al., 2012) .................................. 50
Figure 30. IEC - financing by ESCo (Adapted from: Wurtenberger, Blely et al., 2012) ................................. 50
Figure 31. Practical example of IEC contracting - Austria (Source: Bleyl, 2008) ............................................. 51
Figure 32. Simple lease arrangement (Adapted from: Wurtenberger, Blely et al., 2012) ................................. 53
Figure 33. Leasing with the involvement of an ESCo (Adapted from: Wurtenberger, Blely et al., 2012) .... 54
Figure 34. Practical example of a leasing ESCo model - Sittard, the Netherlands (Source: Bleyl, 2010) ...... 54
Figure 35. Principle of on-bill financing (Adapted from: Wurtenberger, Blely et al., 2012) ........................... 55
Figure 36. Proposed financial model for rented houses in Waalwijk.................................................................. 56
Figure 37. Framework for energy-saving behaviour in urban households in China (Source: Yue, Long, et
al.) ................................................................................................................................................................................... 59
List of tables
Table 1. Summary of collected data ......................................................................................................................... 19
Table 2. CFL vs. LED ................................................................................................................................................ 21
Table 3. Lamp usage data for residences/day ......................................................................................................... 21
Table 4. Retrofitting with LEDs ............................................................................................................................... 22
Table 5. Power savings/dwelling due to lighting retrofits .................................................................................... 22
Table 6. List of lamps used in the De Leest ............................................................................................................ 22
Table 7. Savings due to window retrofits ................................................................................................................ 24
Table 8. Gas savings for insulation of different surfaces ...................................................................................... 26
Table 9. Gas savings due to insulation ..................................................................................................................... 26
Table 10. Reduced energy consumption .................................................................................................................. 26
Table 11. Summary of solar PV output for the houses ......................................................................................... 30
Table 12. Proposed PV design for the apartments ................................................................................................ 33
Table 13. PV system design for the theatre ............................................................................................................ 34
Table 14. Specifications of the NIBE F1245 .......................................................................................................... 38
Table 15. Specifications of the NIBE Split (8 kW) ................................................................................................ 40
Table 16. Financial analysis of proposed options for a house ............................................................................. 44
Table 17. Financial analysis of proposed measures for the apartment building................................................ 45
Table 18. Financial analysis of proposed measures for the theatre ..................................................................... 45
Table 19. EPC, ESC and IEC - a comparison ........................................................................................................ 48
-8-
1 Introduction
1.1 What is a net-zero energy community?
A zero-energy community consists of buildings that are net- zero energy; that is, buildings that produce as
much energy as they consume over the course of a year. It may also be that the community as a whole, is
net-zero energy, and not each individual building. A variety of definitions and classifcations are available
for such buildings, as elaborated in [1]. However, in this case, the basic concept of a net-zero energy
dwelling is considered.
1.2 Waalwijk: an overview
Waalwijk is a city in southern Netherlands (Figure 1), and
has a population of about 28,000. It is a densely populated
city, mostly consisting of houses and office buildings. The
nearest railway stations are Den Bosch and Tilburg. The
‘Centrum’ or the city centre houses an old, quaint church,
the old town hall and a modern shopping district (Figure 2).
A portion of the centre of the city is called the
‘Vrijheidsbuurt’ or the ‘freedom area’. This was the area
through which the Allied army forces marched after their
victory in World War II. Most of the houses here are from
that period – that is, they were built before or just after the
war. It is a historical area, which the city of Waalwijk wishes
to preserve.
Figure 1. Location of Waalwijk (source: Google Maps)
Figure 2. ‘Waalwijk centrum met stadhuis’ (Source: Panaromia)
-9-
Climate:
Most of the Netherlands, including Waalwijk, enjoys a temperate climate. This is mostly due to the
proximity of the North Sea and the Atlantic Ocean, which lead to the maritime climatic conditions. Snow
is experienced on very cold days – mostly in January and February. Rain can be expected around the year.
Summers are relatively mild and humid, with temperatures generally below the 30 ° C mark.
1.3 Project description and goals
Background:
Like an increasing number of cities and towns in the Netherlands, Waalwijk has the ambition of becoming
a net zero-energy town. The municipality wishes this idea to be transformed into concrete action, and thus
came about this project to investigate the various ways in which this goal can be achieved. The
Figure 4. Average days with precipitation - Waalwijk, Netherlands (Source: Norwegian Meteorological Institute)
Figure 3. Temperature data for Waalwijk, Netherlands (Source: Norwegian Meteorological Institute)
-10-
municipality of Waalwijk is working alongside Casade (a housing corporation that provides houses on rent
and for sale), on this project.
The impetus for this project can be traced to recent developments in the EU, regarding energy policy. In
2007, as per the EU communication ‘Renewable Energy Road Map – Renewable Energies in the 21st
century: building a more sustainable future’, the European Union passed a resolution that 20% of all
energy produced in the EU should be from renewable resources [2]. This would also positively impact
CO2 emission reductions; it is predicted that it would lead to a reduction of 600-900 Mt of CO2 by 2020
[2]. However, the target for individual countries is different.
The above directive, when applied in the context of the Netherlands, requires that 14% of the energy mix
must come from renewable sources [3]. Moreover, in November 2007, the ‘Climate agreement
municipalities and Dutch government 2007-2011: working together on a climate-proof and sustainable
Netherlands’ was accepted by the Dutch government and various municipalities [4]. As per this
agreement:
i. Target renewable energy to be 20% of the energy mix by 2020
ii. All new houses developed should be energy-neutral by 2020
iii. Energy consumption in existing buildings to be halved
In addition, on 19th May 2010, the ‘Energy Performance of Buildings Directive’ 2010/31/EU (EPBD) was
adopted by the EU (This was a re-cast of the Directive 2002/91/EC of the European Parliament and of
the Council of 16 December 2002, on the energy performance of buildings). Since buildings consume
40% of the total energy in the European Union, this directive defined the steps to be taken by Member
States regarding energy efficiency in buildings [5]. As per Article 3 of this directive, all Member States
must set up a methodology to calculate the energy performance of a building [5]. Article 4 talks about
ensuring minimum energy performance parameters for buildings. In addition, by 31st December 2020, all
new buildings should be nearly-zero energy [5].
In the light of the above developments (and preceding events), on January 1st 2008, the Netherlands put in
place the ‘Energy Performance Certificate’ for existing buildings. As per this system, an ‘Energy class’
ranging from A-G is assigned to a building, based on certain parameters – A being the most efficient, and
G being the least [6]. The EPC also provides suggestions on what steps can be taken by the building to
become more efficient. This system is required to be implemented for all buildings - public, private as well
as those that come under social housing. Moreover, all property transactions must include a declaration of
the EPC class [6].
Waalwijk: Towards net-zero energy:
With the above background, the local municipality has a target of Waalwijk becoming a net-zero energy
city, and wishes to ensure that buildings in Waalwijk are as energy-efficient as possible. In order to achieve
this ambitious goal, this project was launched in collaboration with Casade, the housing agency. Casade is
currently in the process of certifying its buildings by the EPC method and also wishes to study how to
make its buildings more energy-efficient. Moreover, rising energy costs are a concern for their tenants,
since energy bills are not part of the rent, and are to be paid by the tenants themselves. This may lead to a
loss of clients in future.
Thus, one of the main objectives of this project was to study as many kinds of buildings as possible –
rented, private, public, commercial, etc. This would ensure that the outcomes of this project can be
applied to as many other buildings as possible.
-11-
Aims and outcomes:
i. A study of the energy consumption of the buildings in the selected zone of Waalwijk
ii. A practical, real-time net-zero energy design, along with maximum reduction in energy
consumption, for the selected zone
iii. Potential sources of renewable energy evaluated in the context of Waalwijk, by making wise use of
available resources
iv. Financial analysis of the proposed options, along with ease of implementation and social
acceptability
v. A final zero-energy model/framework that can be implemented in all houses and buildings of
Waalwijk
vi. Recommendations for future work, if any
The municipality of Waalwijk requires that the recommendations given are realistic and can be
implemented by the municipality and residents. Thus, as far as possible, attempts have been made to
approach professionals/companies that provide services in the field of energy-efficiency and renewable
energy. Data/quotes have been obtained from them, along with costs, which are specific to each case. In
addition to giving a realistic estimate of costs, this would also make it easier for the municipality to enlist
their services at a later date.
It has been noted that the economic aspect of such projects is a major barrier to their realization [7]. Such
projects involve a number of parties (authorities, planners, corporations, citizens, service providers), each
with a different agenda and set of limitations. The main question of who will provide the money and how
much, is often a major hurdle. Thus, one of the important requirements of this project was to study the
various financial models and mechanisms that can be applied to such endeavors. Based on the analysis, a
potential financing model is to be suggested for this project.
-12-
2 Methodology
In this chapter, the methodology followed to execute the assigned task shall be discussed.
2.1 Trias Energetica
This is a concept most popularly use in the building industry to design low-energy buildings.
The concept of ‘Trias Energetica’ was introduced by Lysen (1996) [8]. It was a strategy for sustainable
energy supply, and had the following three main points:
i. A continuing improvement of energy efficiency;
ii. A bigger use of sustainable energy sources;
iii. A cleaner use of the remaining fossil fuels.
This was further structured and refined by Duijvestein (1997) especially for buildings, as follows [8]:
i. Use less energy by taking energy saving technologies;
ii. Use sustainable energy sources as much as possible;
iii. When there is still an energy demand left, then use fossil fuels as efficiently as possible.
2.2 Project execution plan
Thus, based on the above principle and certain practical aspects, the project execution plan is as follows:
i. Selection of a zone. This is based on various criteria, such as types of buildings (rented, private,
public, age of building), residential/non-residential, ease of applicability of energy-efficiency
measures, etc;
ii. Data collection (energy consumption, behavioural aspects, residents’ views) by visits;
iii. In case of lack of data, suitable assumptions to be made (wherever possible);
iv. Based on (iii) and (iv), calculate the actual energy consumption of the zone;
v. Reduction of energy consumption as far as possible;
vi. Supply of reduced energy demand by available renewable sources;
vii. Financial analysis of the proposed measures
viii. Analysis of existing financial models and a proposal for Waalwijk
Figure 5. Trias Energetica
-13-
3 Selection of zone and data gathering
3.1 Types of buildings covered
As explained earlier, one of the aims of the project is to study as many kinds of buildings as possible. This
means the selected zone should include a good mix of private as well as rented houses; individual houses
and apartments; residential and non-residential buildings and buildings constructed at different times.
Based on the requirements, and ease of execution, a zone was selected at the centre of the city. The
location and perimeter of the zone is indicated in Figure 6 and Figure 7.
Figure 7. The selected zone (Source: Google Maps)
Figure 6. The extent of Waalwijk (Source: Google Maps)
-14-
The streets taken into consideration are as follows:
Vredesplein
Victoriestraat
Engelsestraat
Poolsestraat
Schotsestraat
Canadesestraat
Putstraat
Touwerij
The buildings considered initially were (source: Google Maps):
i. The bus station: This was chosen since it has a good roof area that can be utilized for the production of electricity.
ii. The houses on Victoriestraat, Engelsestraat,
Poolsestraat, Schotsestraat, Canadesestraat
and Putstraat. These houses were built just
after the war in the 40s, and have historical
significance. They would like to be maintained
in the current condition, but being old, their
energy profile needs to be improved. The
analysis of at least two-three houses here
(rented and private) can be applied to the rest
of the similar houses.
iii. Towerij: This street has houses that were built in
the 80s and 90s. This adds to the mix of
buildings considered.
Figure 8. The bus station Vredesplein
Figure 9. Engelsestraat
Figure 10. Towerij
-15-
iv. Modern apartments at 51, Vredesplein: These
apartments (called Vredesstaete) are quite
new, and can represent the newest residential
area. One apartment in this block shall be
considered.
v. Commercial building on Vredesplein: This
building (28, 34 Vredesplein), on one side of
the bus station, has offices and the building is
fairly new.
vi. The theatre on Vredesplein: The theatre,
called Leest, represents the public/commercial
part of the city.
Figure 11. Apartment building - Vredesstaete
Figure 12. Commercial building on Vredesplein
Figure 13. De Leest
-16-
3.2 Visiting houses
The next step was getting in touch with residents and visiting them. This turned out to be a long
procedure, since it involved approaching the local citizens’ committee and requesting them to discuss the
aims of this project with the residents. Thus, a brief description of the project (in Dutch) was presented to
the local committee. Based on this, five residents agreed to share information. In addition, the theatre De
Leest and the Casade office were also studied. The list was as follows:
- One apartment from the new building on Vredesplein (Vredesstaete)
- One private house on Touwerij (built in the 80s)
- One rented house on Poolsestraat (1940s)
- One private house on Engelsestraat (1940s)
- One rented house on Victoriestraat (1940s)
- De Leest
- The Casade office (part of the apartment building Vredesstaete)
A list of questions was presented to the resident at these meetings. It requested basic information like gas
and energy consumption, details of the heating systems, etc. The complete list is part of Appendix A.
Several attempts were made to collect information from the offices in the commercial building,
Vredesplein. However, they were not very successful. The building consists of offices of 5-6 different
companies, for which there was no focal point of contact. Thus, this building was not considered in the
actual analysis.
Also, though the bus station was initially considered, the municipality was doubtful whether it would be
possible to make modifications in the roof. This is because the bus station is public property, and making
any changes in it would require approval and permissions from a number of parties. Hence, this structure
was also not included in the actual analysis.
3.3 Brief description of houses visited
1) Modern apartment - Vredesplein:
As mentioned earlier, this is an apartment in the fairly new building on Vredesplein, which also houses the
Casade office. The building was built in 2004, and has 21 apartments. The flat is occupied by an elderly
couple. Since the building is new, it is well insulated with polyurethane sheets, and has double-glazed
windows. The heating system consists of regular radiators on the walls, supplied by a combi-kettle HR gas
heater (brand – AGPO). The lighting in the house consists mainly of CFLs and halogens (in the kitchen).
The energy consumption and other details are listed in Table 1 (Page 19) for all the houses.
2) Individual house on Touwerij:
This corner house was built in the 1980s, and is newer than most houses in the ‘Vrijheidsbuurt’. The house
is privately owned, and is occupied by a couple. Having been built after the 1970s, the house is well
insulated, with rockwool in the walls and polyurethane sheets for roof insulation. The windows are plain
double-glazed. The heater is a regular Vaillant boiler, and the rooms are heated by radiators. The lighting
in the house consisted mainly of incandescent lamps, and a few halogen lamps in the kitchen.
-17-
3) Individual house on Poolsestraat:
This is house owned by Casade, and was built just after World War II, in the late 1940s. Being old, there is
no insulation whatsoever in this house, which explains the relatively high gas bills. However, in this
particular house, the residents have isolated the roof at their own cost. The windows are all simple
double-glazed, and the heating system consists of a regular Valliant HR boiler and radiators. The lighting
consists of a mix of halogens and incandescent bulbs; there were no energy-saving lamps in use. The
couple lives alone in the house, since their two children had just moved out the previous year.
4) Individual house on Engelsestraat:
This is a two-storey house privately owned and built just after the war. Again, there is no insulation in this
house, and hence the gas bill is rather high for a house of that size. The house is occupied by just one
gentleman, whose wife had just passed away the previous year. She had been ill for some time, and
needed an oxygen pump that worked on electricity. This led to a large energy bill. The windows are plain
double-glazed, and the heater is a regular HR boiler, with radiators for distribution. There is also a pool
with a pump, which draws quite a bit of electricity. The lights in the house are all mostly halogen lamps
and a few incandescent ones.
5) Individual house on Victoriestraat:
This ‘two-under-one roof’ house is rented out by Casade, and houses six bedrooms. There is only an old
lady living alone (her parents and siblings used to live here with her before), and she is mostly confined
only to the ground floor of the house. As expected, the house has no insulation whatsoever, and is
extremely cold and draughty in the winter. The energy bills are quite high, even though there is only
person in the house. The windows on the ground floor are double-glazed, but the ones on the upper
floors are single-glazed. The house is not centrally heated, but has a ‘gas kachel’ or a gas stove in each
room. This accounts for the high energy bill. The lights are a mixture of CFLs and halogen lamps.
6) The theatre – ‘De Leest’:
‘De Leest’ is a public theatre, and the land is rented out by the municipality of Waalwijk. It sits in the
middle of Vredesplein, and has a huge open square in front, and the bus station behind. The theatre has a
large foyer, with a glass façade and a revolving door at the entrance. The foyer has a cafeteria, and a
number of tables where customers can eat and relax over drinks. There are toilets and a shower for men
and women. To the left of the foyer is the theatre with the stage and seats for the audience. The theatre
uses a number of high-wattage, powerful stage lights. The theatre room is mechanically ventilated, with
vents below the seats to control the incoming air, and a common vent to remove the outgoing air. The
controls are outside the room, and the challenge is to maintain a perfect balance between the temperature
in the room and the oxygen level. There are a few meeting and office rooms on the first floor, and the
central heating and cooling machinery on the floor above that. The lighting in the rest of the theatre
consists primarily of TLs, halogens, spot lamps and CFLs. There is a vast flat roof, of approximately 800
m2.
-18-
7) Commercial offices:
Initially, we considered two offices, one being the Casade office, which is in the same building as the
apartments, and the other one, being Vredesplein 28. As mentioned, there was no data available about
Vredesplein 28. The Casade office is a standard commercial space, well-insulated, with energy-efficient
lighting. The energy consumption has been tabulated in Table 1 .
3.4 Observations
A few key observations were made on these visits:
- Most of the residents are above the age of 40, without children (or with children, who have moved
out)
- The windows in most houses are plain double-glazed.
- Every house is quite different in terms of area, lighting, and electricity consumption.
- The heating system is mostly standard – HR boilers and wall radiators. However, one old house still
utilizes the old gas stove for heating. This is highly localized heating, and since the house is very old,
with no insulation, a lot of heat is lost.
- Most of the old houses (rented or owned) are not isolated.
- In houses that do have CFLs, the residents complain that these lamps take too long to light up, and
are not very convenient.
-19-
4 Energy consumption of the zone
Based on the visits, a summary of the gas and electricity consumption, along with other data, is tabulated
below:
Table 1. Summary of collected data
House type Street Year of constru
ction
Area (m2)
Number of houses
of this type
Electricity (kWh)
Gas (m3)
Efficient lighting
Insulation
Windows
Apartment Vredesplein 2004 90 21 3000 700 Yes Yes Double-glazed (HR+)
Individual house
Touwerij
Post 1970s
60 22 4000 1130 No Yes Double-glazed
Individual house
Poolsestraat Pre-1950 44
130
5036 2000 No No Double-glazed
Individual house
Engelsestraat Pre-1950 40 10,000 2400 No No Double-glazed
Individual house
Victoriestraat Pre-1950 45 7956 3206 Yes No Mixed
Casade office
Vredesplein 2004 NA 1 151,800 7500 Yes Yes Double-glazed (HR+)
De Leest, (theatre)
Vredesplein 1996 NA 1 224,594 24,171 Partly Yes
Double-glazed (HR+)
As seen from the table above, there is a wide variation in the electricity and gas consumptions of the old,
individual houses. Thus, in order to calculate the energy consumption of the entire zone, average
electricity and gas consumptions are assumed for each of these old houses. The values are:
- 5000 kWh of electricity
- 2000 m3 of gas
It is to be noted here that these values are not representative of the entire city of Waalwijk. They have
been assumed as an average for this particular zone of Waalwijk.
Also, had the sample size been larger – that is, had more houses been visited, it would have probably
resulted in a slightly different value for the average energy consumption.
For the apartments, the theatre, the Casade office and the houses on Touwerij, the energy consumption
considered is as per the data provided.
With this assumption, the total consumption of the zone comes to 952.8 MWh of electricity and 331,231
m3 of gas.
-20-
5 Reduction of energy consumption
Based on the Trias Energetica, the first step is to study methods to reduce energy consumption. This
generally involves using the passive design strategy - minimizing energy use and maximising solar
potential. There are a number of ways in which this can be done – lighting retrofits, window retrofits,
better insulation, improved heating systems, improving the façade, orientation, shading and so on [9]. For
example, if the windows are oriented to the south (for dwellings in the northern hemisphere), this
maximizes the solar gain, thus reducing the energy to be supplied to heat the room. Consequently,
however, this might lead to overheating in summer [10].
However, for existing buildings, it is rather difficult to make changes in the orientation and façade of the
building. Moreover, since most of the houses in this project are old and have some historic significance, it
would not be easy to make sweeping changes in the façade and structure of the house.
Considering these factors, the following three measures have been identified as the most feasible energy
saving options:
i. Lighting retrofits
ii. Window retrofits
iii. Insulation
We shall now see what the savings with each of these measures shall be:
5.1 Lighting retrofits
Lighting retrofits refer to the replacement of old, inefficient lighting with newer and more efficient ones
[11]. Switching to energy-efficient lighting is one of the first and most effective ways of cutting down on
energy consumption. Generally, most houses use incandescent or halogen lamps that are extremely
inefficient, since they guzzle a lot of energy to fulfill our basic lighting requirements. These energy-
efficient lamps provide the same lighting output while consuming less watts and thus lowering the power
consumption [12].
It has been shown in [13], LEDs are currently the best energy-saving lamps available, followed by CFLs.
Though the initial costs for these are higher than others, they do result in savings over their lifetime due to
reduced energy consumption [14].
Given below is an illustrative comparison of the performance of various kinds of lamps. It gives an
indication of the power consumed by various lamps giving the same output in lumens [15] [16].
Figure 14. A comparison of power consumed by various kinds of lamps
-21-
Figure 14 shows that for the same lumen output (level of illumination), the LED and CFL consumed
much less energy compared to a traditional halogen or incandescent.
Between CFLs and LEDs, CFLs are preferred due to lower cost and a warmer light output. However,
there are other factors that need to be assessed as well. The following table shows how LEDs and CFLs
fare on major points [14] [17]:
Table 2. CFL vs. LED
Parameter CFL LED
Higher initial investment 4-5 * CFL
Longer Lifetime 10,000 hrs 50,000 hrs
Mercury content √ None
Disposal issues √ None
Start-up/warm-up time required √ None
Higher savings √
Based on the above comparison, it is recommended that we replace the old lamps with LEDs. Though the
investment cost is higher than that of CFLs, their prices have been falling rapidly as newer technology is
coming up [18].
In the case of Waalwijk, based on the data collected, we take average values for the number of lamps used
by the residents. We also assume that the lamps in the bedrooms and stairs are used not more than 2
hours/day, and hence for the sake of simplicity, can be omitted from the calculations. The lamps in the
living room and kitchen are used the most, for an average of 5 hours/day. The table below gives an
overview of the lamp usage characteristics of the individual houses and apartment block:
Table 3. Lamp usage data for residences/day
Lighting Apartment Houses
Incandescent Wattage - 40
Number of lamps 6
Halogen Wattage 50 20 10
Number of lamps 2 3 4
CFL Wattage 8
Number of lamps 9
Now, we replace the old lamps in the apartments and houses with LEDs. This is done by checking which
LED wattage will give the same output in lumens as the incandescent and halogen lamps. Thus, the old
lamps are replaced as shown in Table 4 and the savings are calculated in Table 5:
-22-
Table 4. Retrofitting with LEDs
Type of dwelling Halogen wattage
(W)
Replacement LED
wattage (W)
Incandescent
wattage (W)
Replacement LED
wattage (W)
Apartment 50 7 - -
20 4 - -
Individual house 10 4 40 9
Using our assumption of 5 hours of usage/day per lamp, we get the following figures:
Table 5. Power savings/dwelling due to lighting retrofits
Dwelling Current power
consumption (kWh)
New power
consumption (kWh)
Savings (kWh)
Apartment 292 47.45 244.55
Individual house 511 127.75 383.25
For the 130 houses and 21 apartments, this results in a savings of 55 MWh for the zone. Detailed
calculations are available in Appendix B.
In the case of the theatre, The TL (florescent) lamps used are the energy-efficient T8 ones, and do not need
to be replaced with anything else. The spot lamps and other halide lamps are specific to the application,
and cannot be replaced easily. Table 6 lists the lamp details for the theatre.
Table 6. List of lamps used in the De Leest
Type of lamp Wattage Number
TL (Tube light) 58 138
TL (Tube light) 36 53
TL (Tube light) 18 14
CFL (Spaar lamp) 13 83
CFL (Spaar lamp) 18 27
CFL (Spaar lamp) 9 58
Spot lamp 50 15
Spot lamp 100 53
Spot lamp 40 7
Spot lamp 50 10
Spot lamp 100 21
Hqi 400w 400 20
Hpi 75w 75 24
-23-
5.2 Window retrofits
Retrofitting windows means upgrading the existing windows to those that have better insulating
properties. Windows are the one of the major sources of heat leakage from a building [19], since they are
of a different material than the rest of the building envelope and act as thermal bridges. A thermal bridge
is defined as ‘a building element where a significant change in the thermal resistance occurs compared to that of the envelope,
due to the presence of materials with a higher thermal conductivity, as well as to the change in the geometry of the fabric, as in
the case of the junction between roofs, floors, ceilings and walls’ [20]. This means that there is a sudden increase in
the heat loss due to an increase in thermal conductivity of the window, compared to the rest of the
building envelope. Consequently, larger the window area, higher is the heat loss.
The main factor determining the effectiveness of a window in terms of heat loss prevention is the U-value
or the thermal conductivity. This is a measure of the heat transmission through the window - higher the
U-value, more the heat loss [21]. Consequently, we must aim to keep the U-value of the windows as low
as possible.
Window specifications generally involve two U-values: one for the glass and one for the frame [22]. This is
applicable when the entire frame, along with the glass is replaced. This is because the frame is of a
different material – and also contributes to the loss of heat. However, in this case, we shall consider only
replacing the window panes (glass).
As seen from Table 1 (Page 19), the window panes in Waalwijk are mostly plain double-glazed (U-value =
2.8 W/m2K). In fact, some houses have double-glazed windows only in the living room and single-glazed
windows in the bedrooms. This results in quite a significant heat loss from the house.
Thus, we investigate the benefits of replacing these double-glazed windows with more efficient ones. We
study the potential savings in gas when different kinds of windows are used.
In the Netherlands, double-glazing windows are classified as HR, HR+, HR++ and so on. The difference
between these windows is the gas in the space between the layers of glass, and the low emissivity coating,
which increases the insulation and thermal properties of the glass [23].
We now calculate the energy savings with each type of available glass. The assumptions made in this
calculation are as follows:
- Average dimensions of a window: 1.75*0.75
- Number of windows/house: 8
- Total window area: 10.5 m2
- Total annual hours of heating required: 1638 hours
- The indoor temperature is set at 21 °C, while the ambient temperature would vary as per the
season
The basic formula used to calculate transmission loss is as follows [9]:
(Equation 1)
Using average temperature data for Waalwijk as per Figure 3, we calculate the transmission loss with each
kind of window. Detailed calculations are in Appendix C. The results are tabulated below in Table 7:
-24-
Table 7. Savings due to window retrofits
Type of glass U-value
(W/m2K)
Transmission
loss
(MWh/year)
Transmission
loss (m3/year)
Gas savings
(m3/year)
Gas savings
per year in
m3/(m2
window area)
Current double-
glazed glass 2.8 0.64 60
HR 2 0.46 42.86 17 1.6
HR+ 1.6 0.37 34.28 26 2.4
HR++ 1.2 0.27 25.71 34 3.3
HR+++ 1 0.23 21.43 39 3.7
HR3 (triple
glazed) 0.7 0.16 15 45 4.3
Thus, from the above table, we see that as the U-value decreases, the heat loss due to transmission also
reduces. Graphically, this can be represented as:
Figure 15. Gas savings for various types of window glazing
Thus, we see that by upgrading to an HR+ window with U=1.6 (W/m2K), one can save up to 2.4m3
gas/m2 of window area. For one house, this translates to a savings of 26 m3 of gas annually. For the entire
zone, this leads to a savings of 3343 m3/year.
5.3 Insulation
Waalwijk has a good mix of old and new houses, and the major difference between them, are that the old
houses are not at all well isolated. Most houses built in the late 1940s and early 1950s have no isolation
whatsoever, while one resident we met had carried out roof isolation. The houses built in the 1980s, the
apartment block and the commercial buildings have been isolated.
Figure 16 shows the various ways in which heat is lost from the building envelope.
0.0
2.0
4.0
6.0
HR HR+ HR++ HR+++ HR3 (triple glazed) A
nn
ual
gas
savi
ng
s (m
3/
m2)
Type of glazing
-25-
Figure 16. Different ways in which heat is lost from a house, and where isolation is carried out
As in the case of window retrofits, the effectiveness of insulation is measured by the U-value of the
insulation material. A wide variety of insulation materials are available commercially, each different in U-
values, thermal and physical properties and costs. Figure 17 provides a detailed list of such materials [24].
Figure 17. List of commercially available insulation materials (Source: Irish Energy Centre)
-26-
Since the savings by insulation depends largely on the installation, a professional in this field was
approached. Pluimers B.V., an experienced insulation installer was asked to quote for this project. The
company was asked to quote what would be the savings in gas would be after isolation. This value is for a
standard house, and can vary depending on the number of persons living in the house, their behaviour,
and so on. Given below are the values provided by the supplier:
Table 8. Gas savings for insulation of different surfaces
Type of insulation Annual gas saving (per m2)
Floor insulation (without floor heating) 6m3
Floor insulation (with floor heating) 8m3
Insulation of Cavity walls 9m3
Roof insulation 5m3
The above data was used to calculate the savings for an average old house in Waalwijk. For the
dimensions of an average house, drawings of 107 rented houses in this area have been provided by
Casade. Based on average values from these drawings, savings have been calculated as indicated in Table 9
below:
Table 9. Gas savings due to insulation
Thickness
(m)
Area (m2) Gas savings
(m3 /m2)
Savings
(m3 gas
/house)
Total
number
of houses
Total
savings
(m3 gas)
Floor isolation - 42.7 6 256.2 130 33,306
Cavity wall isolation 0.05 58.65 9 527.85 130 68,620
Roof isolation
41 5 205.2 130 26,676
Total 128,602
Thus, the total gas savings is 128,602 m3 per year for the entire zone. Detailed calculations can be found in
Appendix C.
5.4 Total reduction in energy consumption for the zone
Based on the electricity savings due to lighting retrofits, and gas savings due to upgradation of window
panes and insulation, the total reduction in consumption is tabulated as below:
Table 10. Reduced energy consumption
Electricity
(MWh/year) Gas (m3/year)
Old 957 331,231
New 902 225,645
Savings 55 105,586
From the data presented above, we see that good insulation by itself, will lead to a considerable reduction
in the gas consumption of the zone. Efficient lighting can also contribute measurably to electricity savings.
-27-
6 Energy supply possibilities
Having reduced the energy consumption as far as possible, we shall now explore ways in which the rest of
the demand can be supplied renewably. Since Waalwijk is a densely-populated city, dominated by
residential and commercial buildings, options to supply this energy are few. The major sources of
electricity generation were evaluated and ruled out:
- Wind energy: Wind turbines need adequate open space for installation. It is a long term project, which
cannot be implemented on a building level. Moreover, 5 wind turbines (1.5 MW each) have been
installed at the entrance of Waalwijk along the A59 highway, by the energy company Eneco. There are
plans to install 12 more wind turbines in Waalwijk [25].
- Biogas: To produce biogas, there needs to be a constant, cheap supply of agricultural/animal waste
products as feed. This is difficult in the case of Waalwijk, since it is a city. Also, like wind energy, this is
a large-scale project, which is difficult to implement on a local, building level. Moreover, the hygiene
requirements for such projects (disposal of the digested waste) are an important factor to be taken into
account [26], and complicate the implementation of such projects on a small scale.
- Fuel cells: Fuel cell systems are now making an entry in the commercial market – particularly, the
BlueGen fuel cell –driven co-generation machine. The BlueGen runs on natural gas, is extremely silent,
and can produce 60% electricity. However, the price/unit is €39,995 [27] - too steep for residential use.
Thus, based on the above analysis, it was decided that the following technologies would be more suited to
the buildings in Waalwijk:
i. Solar PV
ii. Heat pumps
6.1 Solar PV
Solar panels are one of the most popular methods of generating electricity locally. They do not require
much maintenance, and can be installed on practically any rooftop. The following picture depicts how the
solar panels can be used on an individual house in Waalwijk, if not connected to the grid:
Figure 18. Setup of a stand-alone rooftop PV system
-28-
6.1.1 Brief working of a solar panel:
Solar panels work on the principle of the photovoltaic effect. Certain materials (called semi-conductors),
produce electricity when exposed to sunlight. Usually, two layers of different kinds of semi-conductors (p-
type and n-type) are sandwiched together to form a PN junction, which is the basic component of a solar
panel. When light hits the solar panel, some photons from the sunlight are absorbed. The energy from
these absorbed photons is transferred to the electrons in the semi-conducting material. These electrons get
excited, and start to flow through the panel, and into the external circuit. This flow of electrons
constitutes the photo-voltaic current, as depicted in Figure 19.
6.1.2 Types of solar PV configurations
Solar PV systems can be of the following main types [28]:
1) Stand-alone: These PV systems are not connected to the grid. They have a battery back-up to store the excess electricity generated during the day, to be used at night. 2) Grid-tie: These kinds of systems are gaining popularity in Europe and North America, thanks to attractive financial schemes such as the ‘feed-in tariff’1 program. In this case, the PV output is connected to the grid, and the excess electricity generated is given back to the grid. Generally, the electricity generated during the day is used by the house, and electricity is drawn from grid at night. There is no battery back-up in this case. 3) Grid-tie with power backup: In this configuration, the PV panels are connected to the grid, and have a battery backup. The PV panels charge the battery bank, and the house runs on the electricity from the battery. When the battery runs out, electricity is taken from the grid automatically, while the PV recharges the battery. However, in this case, the feed-in tariff will not be applicable. 4) Grid failover: This system is designed such that the PV panels will supply energy in case the grid fails.
Thus, the electricity from the solar PV will be used only when there is grid failure. The drawback with this
system is that the PV panels are not used to their full potential.
Factors affecting solar PV output:
1 Feed-in tariff: This is a financial incentive used by governments to encourage investment in renewable energy systems. By this scheme, the installer is paid a premium price for the electricity he/she sells back to the grid (produced by renewable energy). [51]
Figure 19. Working of a solar cell (Source: Mariadriana Creatore, Eindhoven University of Technology)
-29-
1) Orientation: The correct orientation for maximum solar gain is the south (for the northern hemisphere). The angle of the PV panel from the true south is called the azimuth angle. Mono-crystalline PV panels have an efficiency of 96% when oriented south,, compared to about 82% when they are oriented east or west. 2) Irradiance (kWh/m2/day): Irradiance is the solar energy available at a certain location, per day. It varies seasonally, and increases as we go towards the equator. 3) Inclination (degrees): The inclination of the solar panels from the horizontal also affects their output.
The angle changes every season, but generally inclinations of 45 to 60° are considered optimal.
6.1.3 Designing the solar PV systems for buildings in Waalwijk
The solar PV system design was split, based on the type of building, as follows:
i. Individual houses
ii. Apartment building
iii. Theatre
i. Individual houses
The solar PV design for the houses is a grid-tie system. There are no specific regulations that need to be
followed; any roof that has potential to produce solar electricity, can install panels. The following steps
were taken to evaluate the solar potential:
- A study of the houses in the area on which PV panels could be installed was carried out. As it happens,
these were not many, since the orientation of most houses in this zone is not suitable for installation of
PV. The total number of houses facing the correct direction is 47.
- Next, an estimate was made as to how many panels can be placed on each house. This was the limiting
factor for the output from each house, and depends on the roof area, possibility of shading and
orientation. The number of panels ranges from 6 to a maximum of 12 on each house.
- This was followed by selection of a PV panel. The panels selected were the Yingli Solar YL230-250P-
29b. This panel has a Wp of 250 W at STC. Its dimensions are 1.65 m x 0.99 m = 1.6 m2, and an
output of 181 W at NOTC.
- Next, the solar irradiance for Waalwijk was calculated from [29]. The nearest location for which
radiation data was available was Tilburg. For PV panels mounted at an angle of 60° and 45°, the value
of solar irradiance is calculated for a day for each month of the year. This is summed up for the year.
Then, the loss in efficiency due to high temperature (Vtemp)2 and reflection losses (Vref)3 is calculated, by
multiplying by their respective factors. The, the inverter and generation losses (electrical losses) are
found, and multiplied. Lastly, the peak power of the module (Ppeak – in kW) is multiplied, and the total
annual for one solar panel is calculated [30]. The detailed calculation can be found in Appendix D. The
formula is:
(Equation 2)
2 Vtemp is the temperature correction factor. This accounts for the loss in the output of the solar panel, due to a rise in temperature. It is calculated for each month, and the irradiation/month is corrected [52]. 3 Vref is the correction factor due to reflection of sunlight at the module surface. This is a constant taken as 0.95.
-30-
- Thus, the total output for a zone comes to 100.703 MWh. The figures are presented in Table 11:
Table 11. Summary of solar PV output for the houses
Street No. of
houses
No. of
panels/
house
Inclination Total
panel
area
(m2)
Total power
of the
system/hou
se (Wp)
Output from
one house
(kWh/year)
Total
number of
panels in
the zone
Total output
(KWh/year)
Touwerij 14 8 60 179.2 2 1706 112 23,889
Victoriestraat 22 12 45 422 3 2483 264 54,632
Schotsestraat 8 10 60 128 2.5 2133 80 17,064
Poolsestraat 2 6 60 19.2 1.5 1280 12 2560
1 12 60 19.2 3.6 2560 12 2560
Total 100.704 MWh
Thus, the total output from the individual houses is 100.704 MWh.
- The next step is to select the inverter. Firstly, an inverter is chosen, based on the maximum output of the solar panels. Then, depending on the temperature conditions in Waalwijk, the maximum and minimum voltages of the system are calculated. This is to verify whether the chosen inverter is appropriate. The Sunny Boy range of inverters is one of the most popular series of inverters for residential use. The Sunny Design Web sizing software was used to calculate the optimum inverter and wire size, for each condition. The inverter chosen for each situation is detailed in Appendix C.
- Then, the arrangement of the array is calculated in conjunction with the type of inverter. Since the number of panels is few, the panels are all sized in a single string, that is, they are connected in series. This is to optimize the output of the inverter.
- The wire sizing is also calculated using the software. Since all the sizes are not very different, the max cable cross-section comes to 2.5 mm2, and a length of 30 m. An example output is shown in the snapshots below.
Figure 20. Wire sizing - an example
-31-
Figure 21. Total inverter sizing output - an example
ii. Apartment building:
A solar PV system on a roof of an apartment building would generally yield a large output. It would
involve the installation of a collective meter for all the panels, which would send the output back to the
grid. The building as a whole, would thus produce (and consume) greater than 5000 kWh, making it a
large consumer. Hence, as per Dutch regulation, the generated electricity has to be sold back to the grid at
a fixed price (€ 0.102 per kWh) that is lower than rate for which it is bought from the energy company (€
0.23 per kWh) [31]. This makes it an unfavourable option (economically) for apartment buildings. If the
same rate is to be paid for the solar power generated (€ 0.23 per kWh), then each apartment has to be
connected to its own set of panels, which would make the process of installing and connecting panels to
each apartment cumbersome. In this scenario, LENS B.V., a professional solar PV design company, offers
an elegant solution, especially for apartment buildings.
This company designs and installs collective solar panels for an apartment building, on the common roof,
and splits the output for each apartment, according to the requirements of each apartment. For this
purpose, they use a patented software program called Herman, which splits the output after the inverter
converts the DC power to AC power. Thus, each apartment gets its designated power supply, without any
interruption. If any resident chooses not to be part of this scheme, then that apartment will not get any of
the solar power generated. Moreover, if any resident is on vacation, or will not need the energy for a while,
-32-
they can transfer it to other residents. This solves the problem of not gaining full advantage of a solar
installation, as well as that of some residents not wanting to be part of the agreement. More information
can be obtained from [31].
The following schematic (Figure 22) details the installation of the system:
In addition to the output sent to the apartments, there can also be a collective meter, which would supply
all the common electricity requirements of the building, like the elevators, the lobby lights, pumps, etc.
This set of panels can be installed separately, and connected to the collective meter. Since there is no
splitting involved, the Herman is not required to be connected in this case. Figure 23 shows the details:
The option for the collective meter depends on the availability of space and whether the residents wish to
have a collective meter.
Figure 23. Scheme for the collective meter – sans Herman
Figure 22. Scheme for the apartments, with Herman
-33-
The proposal by LENS offers three options, based on the space available. The following picture shows
the layout of the roof the apartment building. Roofs 2 and 3 belong to the apartments, while roof 1
belongs to the Casade office.
Table 12 gives a summary of the quote provided by LENS. B.V.:
Table 12. Proposed PV design for the apartments
Solar PV system
Option 1: Solar network on roof
(with ‘Herman’)
Option 2: Solar network on roof 2
& 3, with special construction on
roof 3 (with Herman)
Number of connected
houses
16 21 20 21
Number of solar panels 208 208 260 260
Total maximal output in
Wp 52,000 52,000 65,000 65,000
Total power yield in kWh 45,812 45,812 57,265 57,265
Revenue per kWh € 0.232 € 0.232 € 0.232 € 0.232
For each connected
household
All-in investment € 6025 € 4505 € 6513 € 6186
Power in the first year kWh 2863 2182 2863 2727
Revenue for the first year € 624 € 468 € 624 € 593
Option 1 proposes solar panels on roofs 2 and 3 with either 16 or 21 houses connected; this design can
accommodate 208 panels, which give an annual output of 45,812 kWh.
Option 2 suggests installing solar panels on roofs 2 and 3, with a special construction on the roofs, to
optimize the available space. This would be able to accommodate 260 panels, with an annual output of
57,265 kWh.
Figure 24. Layout of the roof of the apartment building
-34-
There is also an option 3 is for the collective meter – with separate panels to be installed on roof 2. This
would accommodate 51 panels, with an annual output of 11,207 kWh. This can only be combined with
option 1, due to space constraints. Other details of the quote can be referred to in Appendix E.
It must be noted that the above design does not consider supplying the Casade office. This is because,
firstly, there is not enough roof space available to install enough solar panels to supply the energy demand
of the Casade office as well as the apartments. Secondly, the Casade office being a large consumer has a
fuse rating of 3 x 160 Amps, which makes it ineligible to feed electricity back to the grid. However, they
could install PV panels only for their consumption (off-grid system). Thirdly, and most importantly, being
a large consumer of electricity, the office pays only about 9 cents/kWh of electricity. It is cheaper for
them to buy electricity in bulk from the energy company than to produce their own energy. Thus, overall,
manufacturing electricity for large consumers does not always make economic sense. This is also the case
for the theatre.
Thus, the total annual output from the solar PV system (excluding the optional collective meter) on the
apartment building is 57,265 kWh.
iii. Theatre – De Leest:
The solar PV design for the theatre was also quoted by LENS B.V. The conditions for the theatre are very
similar to that of the Casade office. The theatre is a large consumer with an industrial connection of 3x
210 Amps. This limits the profitability of the PV design. There are two ways of approaching this:
a) The theatre consumes all the energy produced for its own activities, and does not send anything back to
the grid. This would mean that it would save only as much as it pays currently for electricity. this is the
proposal suggested by LENS B.V.
b) Alternatively, the energy company can be contacted for a better compensation to send electricity back
to the grid. This requires close collaboration with the company (Enexis, in this case), as it can provide a
good deal on the electricity sent back to the grid. This would require a measurement company to assess
the output and enable the network operator to use the data.
The proposal put forward by LENS B.V. is as below:
Table 13. PV system design for the theatre
Solar PV system Collective meter
Connection 1
Number of solar panels 276
Total maximal output in Wp 69,000
Total power yield in kWh 61,272
Revenue per kWh € 0.106
-35-
A schematic of the suggested system is as follows. Note that since there is no splitting required, there is no
Herman used in this case.
The electricity generated by solar PV on the theatre is 61,272 kWh/year. Please refer to Appendix E for
details.
Thus, the total electricity generation potential by solar PV in the zone is:
Building Electricity production by solar
(kWh )
Individual houses 100,704
Apartment building 57,265
Theatre 61,272
Total 219,241
We see that the total production by solar PV is 219,241 kWh, compared to the demand of 902,000 kWh.
This represents 25% of the total electricity demand.
6.2 Heat pumps
Heat pumps are one of the most popular renewable energy technologies in use today. They supply heating
and cooling to a building, thus eliminating the need to use natural gas. Practically, it might not always be
possible to completely eliminate traditional gas boilers, but they can serve as back-up on extremely cold
days. Of course, heat pumps need energy to run, which is supplied by electricity. Also, the house must be
insulated well enough, so that the heat pump works as efficiently as possible.
Figure 25. Schematic of PV system for the theatre
-36-
6.2.1 Working and efficiency of a heat pump
A heat pump is a device that draws heat from a particular location and transfers it to another [32]. It runs
on electricity, and transfers the heat with the help of a refrigerant. The working of a heat pump (to heat) is
similar to that of a refrigerator or an air-conditioner, which cool. Figure 26 describes the working
principle of a heat pump.
Heating cycle: The refrigerant (a fluid with a low boiling point) absorbs heat from the outside/ground
(depending on the type of heat pump). The fluid evaporates, and the vapour passes through the
compressor, where it gets compressed to a higher pressure. The compressed vapour then goes on to the
condenser. Here, the vapour gives out the heat absorbed from the source, to a medium (water or air), and
in the process, changes to a liquid. This high-pressure liquid then passes through an expansion valve,
which reduces the pressure on the liquid. Thus, the refrigerant returns to its original liquid state and the
process continues.
Cooling cycle: In this cycle, the process is reversed – that is, the refrigerant absorbs heat from the inside of
the room/house, and dumps it outside. The components of the system remain the same, only the
direction of the fluid changes. Thus, the same heat pump can be used for heating as well as cooling.
The efficiency of a heat pump is usually determined by a factor, called the Coefficient of Performance
(COP). It is defined as:
(Equation 3)
The higher the COP, the more efficient is the heat pump in converting the input energy into useful
output. If the COP of a pump is 4, it means that the heat pump gives out 4 times more energy than it
uses. For example, if the heat pump uses 1000 kWh of electricity with a COP of 4, it means it delivers
4000 kWh of heat. This can be converted to m3 to find how much of gas is saved.
Figure 26. Working principle of a heat pump (Source: Save Your Energy)
-37-
There are also other terms to express heat pump performance like the Heating seasonal performance
factor (HSPF), which determines the heating efficiency and the Seasonal energy efficiency ratio (SEER),
which measures the cooling efficiency of a heat pump.
The ‘thermal balance point’ is the temperature at which the heat that is lost by a house is fully supplied by
the heat pump. Thus, the heat pump is running at an optimum point, and there is no need for back up
heating [32].
There is also the ‘economic balance point’ – the temperature at which the expenditure to run the heat
pump, is the same as that required to run the alternate/auxiliary heating system [32]. Below this point, it is
not economically viable to operate the heat pump. Both these points are extremely essential in
determining the most optimal design of a heat pump.
6.2.2 Types of heat pumps
There are two major groups of heat pumps, based on the source of heat: Air-source heat pumps and
ground-source heat pumps. We shall discuss these further:
(a) Air source heat pumps (ASHP):
As the name suggests, the source of the heat for the pump is the outside atmosphere. Even on the coldest
winter days, the air does contain some heat that can be utilized. Since the refrigerant has a low boiling
point, it absorbs the little heat present in the air, and evaporates. This evaporated refrigerant then cools in
the condenser, and transfers its heat to a medium. The medium could be air or water depending on the
terminal system. Generally, air-to-water heat pumps are used when there is already a water terminal system
in place – such as radiators, floor heating, wall heating, etc. Air-to-air heat pumps are used when the area
to be heated is small, or when there is a central air heating system in place.
The efficiency of the ASHP depends to a large extent on the outside temperature. As the temperature
outside falls, the rate of heat loss from the house increases. This means the ASHP has to do more work to
maintain the same internal temperature, while the source temperature is falling. More work means a lower
COP, and hence this reduces the efficiency of the ASHP.
(b) Ground-source heat pumps:
These heat pumps draw their heat from the ground. Usually, as we go below the ground level, the warmth
increases (in winter, and vice-versa in summer). This property is utilized by the ground source heat pump.
The process involves sending water through pipes installed to a certain depth in the ground. The water
draws heat from the soil, and transfers it to refrigerant. The refrigerant then continues the process in the
same way as the air source heat pump.
Sometimes, the water that is pumped underground is not the same as the one that transfers heat to the
refrigerant. This is called a closed-loop system – when the water that is drawn from the ground is different
from the circuit that delivers the heat to the refrigerant. The water that is sent underground transfers heat
to the other circuit (which sometime contains an anti-freeze solution) via a small heat exchanger, after
which heat is given to the fluid.
Ground-source heat pumps are generally more efficient, since the temperature below ground is quite
stable, compared to that of the air. However, the initial investment for these kinds of pumps is also higher,
since it involves drilling and laying of underground pipes.
-38-
6.2.3 Heat pumps in Waalwijk
Having obtained an overview of the working of heat pumps, we now see how they can be applied to
Waalwijk.
Heat pumps were proposed for the individual houses, the apartment building as well as the theater. Since
the design is complicated, it was decided to approach an expert in this field. Thus the manufacturer NIBE
(a member of the Dutch Heat Pump Association) was contacted in this regard. NIBE is a Swedish
company, which has been forefront in the manufacture and installation of heat pumps for a number of
years. They have considerable experience in designing heat pumps for the coldest of environments, and
have also executed a number of community projects.
i. Individual houses:
In order to give an approximate quote for the heat pump, NIBE requested certain basic information such
as the gas consumption, area of the house, and the year in which it was built. As mentioned earlier, it was
assumed that each house has a gas consumption of 2000 m3/year and 45 m2 of ground area. With an 80%
efficiency of insulation and window retrofits, the heat demand/house comes down to 1188 m3/year.
For the house described above, NIBE used their internal software sizing program called VPDIM, to size
the heat pump. Based on the profile, two models were proposed – an air source heat pump (ASHP) and a
ground source heat pump (GSHP).
(a) GSHP:
The 5 kW GSHP could be either the NIBE F1145 or the NIBE F1245. Both have the same capacity, but
the main difference is that the F1245 comes with an integrated immersion heater. Both can fulfill the
entire heat demand of the house.
Specifications: The technical specifications of the F1245 are as follows [33]. Details can be obtained in
from the brochure online as indicated in [33]:
Table 14. Specifications of the NIBE F1245
Size 5 kW
Net weight 305 kg
Refrigerant R407C
COP at 35°C 4.44
COP at 50 °C 3.13
How water tank capacity 180 liters
Immersion heater (max) 9 kW
Source of heat:
The NIBE GSHPs can use four different sources as heat [33] – they are:
1) Using a ground probe (rock): This involves drilling a hole (vertically) in the lower sub-soil, to a
depth of 90-200 m, through which water or anti-freeze circulates. This system is suitable for all
kinds of buildings and houses, since it requires little space.
-39-
2) Using a surface collector (surface soil): This utilizes the heat of the sun stored in the upper layer of
the soil. A hose of length 205-400 m is installed horizontally, at a depth of about 100 cm. anti-
freeze is circulated in the hose, which absorbs the heat from the soil.
3) Using available ground water: Any building that has access to ground water can use it as a hat
source. The installation includes two wells, one to draw water from, and the other to return it.
4) Using lake water: Water form lakes can also be used as a source of heat. Pipes can be installed at the
bottom of the lake to draw the water out.
In the case of Waalwijk, options 1 and 2 are most suitable. Option 2 would incur lesser costs, since the
depth to be drilled is not much. However, the performance in case of option 1 would be better, since the
temperature at a depth of 90 m would be higher than that at 100 cm.
Figure 27 shows a simplified installation diagram for the F1245 (adapted from [33]):
The above installations scheme will hold true for almost any other heat pump. The major differences will
be the source of the heat and storage of hot water.
Immersion
heater
Heating medium
(water) return
Shut off valves
Hot water
Probe/surface
collector
Reversing valve
Charge coils for
DHW
Heating cylinder and storage
Compressor
Evaporator Condenser Expansion
valve
Brine supply
Brine return
Cold water
Refrigerant
circuit
Heating medium
supply – to radiators
Figure 27. Schematic working and installation of a GSHP
-40-
The energy savings are calculated as below:
- Based on the sizing provided by NIBE, the electricity required to run the heat pump (with a COP of 4)
to supply this heat demand, is 2400 kWh/year (heating only)
- Thus, the electricity cost for the heat pump is €552
- The gas saved is 1188 m3, which translates to €772
- Thus, the savings is €220/year
(b) ASHP:
The ASHP suggested is the NIBE Split with the indoor unit ACVM 270 and the outdoor unit AMS 10-8.
The NIBE Split ASHP would be the best option, if drilling is not possible or not preferred by the
resident.
ASHPs have an outdoor unit and an indoor unit, which have to be within 12 meters of each other, for
optimal performance [34]. In the heating mode, the outdoor unit acts as the evaporator, while the indoor
unit contains the condenser and the compressor. Some ASHPs have the entire system installed as a block,
indoors. In this case, as mentioned, there is an outdoor as well as an indoor unit.
The installation of ASHPs is generally quite simple – the two units need to be connected up, and some
values need to be set. These heat pumps can also be easily connected to the existing heating system (gas
boilers) for back-up. Moreover, if required, they can also be hooked up to solar panels to provide the
electricity needed to run them.
The technical specifications of the NIBE split (8-10 kW) are as tabulated below. Refer to [34] for details:
Table 15. Specifications of the NIBE Split (8 kW)
Size 8 kW
Net weight 305 kg
Refrigerant R407C
COP at 35°C 4.44
COP at 50 °C 3.13
How water tank capacity 180 liters
Immersion heater (max) 9 kW
The working and installation of an ASHP is more or less similar to that of a GSHP, as shown in Figure
27, except that there are two units involved. The flows of the various fluid circuits remain the same.
The energy savings with the NIBE Split are as follows:
- Electricity required to run the heat pump (with a COP of 3.5) to supply the total heat demand, is 2616
kWh/year (heating only)
- Thus, the electricity cost for the heat pump is €601
- The gas saved is 1188 m3, which translates to €772
- Thus, the savings is €170/year
-41-
As can be seen in both cases, the savings is not considerable to make it a profitable proposition, though
the initial investment for an ASHP is less than that for a GSHP. This was discussed with NIBE, and the
following factors were identified as potential reasons:
- Heat pump designs are highly specific to a house, and must be sized for a particular building load. A
heat pump is sized for based on heat loss data which depends on numerous factors like area,
occupancy, set design temperature, insulation etc.
- An over-sized heat pump will be inefficient and lead to higher running costs. Moreover, it would
reduce the compressor life cycle [35]. Similarly, an under-sized heat pump would be ineffective and not
heat the house properly, since the heat demand would be too much to deliver. It would also lead to
frequent de-frosting4 in ASHPs.
- Thus, in order to calculate the exact savings that can be achieved by using a heat pump, a detailed
technical and site analysis is required to be done. This can only be done at a later stage, not in the initial
phase of a project.
- The figures are quite conservative, and only indicative of whether a heat pump is suitable and which
kind of heat pump can be used.
ii. Apartments
The apartment building is a different case, since the layout of a building is very different from that of an
individual house. Based on the data collected, we see that the average annual gas consumption of an
apartment is 700 m3, which makes the total annual gas demand of the building 14,700 m3. For this
building, NIBE again suggests two options: a central GSHP and a central ASHP.
(a) Central GSHP:
This option has two central GSHPs. Each HP has a capacity of 80 kW. 98% of the heat demand would be
supplied by the heat pumps (two 40 kW each), while 2% would be supplied by the gas boilers. The savings
are calculated as:
- Model number: F1345
- Annul electricity consumption of heat pump to deliver this heat– 30,600 kWh
- Electricity costs: €6732
- Gas boilers deliver 2500 kWh of heat : 294 m3 of gas = €175/year
- Total energy costs: €6907
- Gas saved: 686 m3/year = €490/house
- For 21 houses, this gives a savings of €10,290
- Total savings: €3383/year
Details are available at [36].
4 ASHPs go through a de-frosting cycle from time to time in the heating mode. When the ambient temperature goes near or below the freezing temperature, moisture in the air condenses and freezes on the heat pump. This reduces the efficiency of the heat pump, and in order to remove this, the heat pump switches to cooling mode which heats the coils, and gets rid of the frost/ice. Frequent de-frost cycles affect the performance of a heat pump adversely [32].
-42-
(b) Central ASHP:
This option has four central ASHPs. Each HP has a capacity of 20 kW. Again, 98% of the heat demand
would be supplied by the heat pumps, while 2% would be supplied by the gas boilers. In this case
however, the energy saved is 20% less than that GSHP. Details of this model are available at [37]. The
savings are calculated as:
- Model number: F2300
- Annul electricity consumption of heat pump to deliver this heat– 36,720 kWh
- Electricity costs: €8078
- Gas boilers deliver 2500 kWh of heat : 294 m3 of gas = €175/year
- Total energy costs: €8253
- Gas saved: 686 m3/year = €490/house
- For 21 houses, this gives a savings of €10,290
- Total savings: €2036/year
iii. Theatre
The theatre has an annual gas consumption of 24,171 m3. This is a large amount that can only be supplied
by a ground source heat pump. NIBE proposes two 60 kW F1345 ground source heat pumps, with the
boiler as backup for peak load. Details of the model can be obtained at [36].
Calculations:
- Model: F1325
- Gas savings: 16,187 m3/year = €10,522
- Electricity required for GSHP : 22,400 kWh = €4,928
- Gas required for regular boilers at peak: 7984 m3/year = €5189
- Total annual savings: €5905
Points to be noted about heat pumps in Waalwijk:
- The ground source heat pump for the theatre and apartment has a variable investment, which depends
largely on the drilling costs. This varies widely form case to case, and depends on the ground
conditions, the depth to be drilled, the kind of soil, and so on.
- Gas boilers are still required as back up in the apartment and the theatre. This should be avoided as far
as possible for the houses, since there is still a connection charge to be paid/year for the gas.
- As mentioned earlier, the performance of the heat pumps can be optimized for best performance if it
is sized correctly as per the heat loss from each house.
-43-
7 Financial analysis
In this chapter, the investment needed for the above mentioned measures shall be calculated, along with
an estimate of their feasibility. This is also called a cost benefit analysis (CBA).
7.1 Methods used to calculate profitability
In order to evaluate how each measure fares, the following tools are used:
i. Simple payback time: Payback time is the time required to recover the investment, taking into account
various factors like the revenues and the recurring costs. However, this does not account for inflation
or the market interest rate. The payback depends a great deal on the regulations which determine how
much profit can be made.
ii. Net present value (NPV): The NPV is also known as the ‘time value’ of money. In modern economics,
it is assumed that the value of money reduces over time. This means that 100 Euros invested today will
not have the same value after 10 years – it would have reduced in value. This value depends on the rate
of inflation. Thus, investments are evaluated taking into account interest rates and inflation – this is
also called the discounted cash flow [36].
In this method, the total cash flow from non-financial operations (subsidies, other earnings) is
calculated over the lifetime of the project. If the total cash flow is greater than zero over the lifetime,
then it is considered a profitable venture.
iii. Internal rate of return (IRR): the IRR is the rate of profitability of the project. It is the interest rate at
which the sum of the NPV over the life of the project is zero. The IRR should be greater than the
market rate of interest.
Each technology is evaluated separately, for each kind of building. This is done for the following reasons:
- Easier to make a comparison of viability of a certain technology, for different buildings
- Calculating an overall investment for a particular building will not give a clear reflection of which
measure contributes to a better return on investment
- Separate paybacks will indicate which measures can be improved or eliminated altogether.
7.2 Subsidies
A note must be made here regarding subsidies. Investment subsidies for solar PV were made available by
the Ministry of Economic Affairs, under the ‘Subsidieregeling Zonnepanelen’ scheme for the years 2012-
2013. By this scheme, residential PV systems with a minimum capacity of 0.601 kWp and a maximum of
3.5 kWp are eligible for a subsidy of 15% of the purchase costs or a maximum of €650, whichever is less
[37]. The budget for this scheme was €50,882,000 for the period of two years. As of today, however, the
number of applications has exceeded the available grant [37]. Additionally, a new scheme for renewable
energy techologies was introduced by the Ministry of Economic Affairs in 2013, called the ‘Stimulering
Duurzame Energieproductie’ or SDE+ (2013). This scheme sets a feed-in tariff for energy generated by
various renewable energy technologies [38]. However, only solar PV systems which have a capacity greater
than 15 kWp are eligible for this scheme.
Though heat pumps and insulation count as renewable energy and energy efficiency measures, there is no
investment subsidy available for them. They can receive loans at lower rates or tax deductions (this will be
discussed further in Chapter 8). Hence, no subsidies have been taken into account in the calculations.
-44-
7.3 Analysis of the proposed measures
The cases considered are:
i. A house
- Window retrofits and insulation
- Air source heat pump
- Solar panels (6 panels)
- Solar panels (12 panels)
Two separate cases of the solar panels have been considered since the number of panels is not the same
for each house. Using the minimum and maximum values will give an idea of the range of the payback
period for the solar panels.
ii. Apartment building
- Solar PV
- Ground source heat pump (more profitable)
iii. Theatre
- Solar PV
- Ground source heat pump
The data considered/assumed in the calculations are as follows:
- Market rate of interest (i) = 4% [39]
- Inflation (p) = 2.9% [40]
- Real rate of interest (r) = 1.07% 5
- Lifetime: 30 years
The values of the payback times, NPV and IRR for each proposed option are tabulated henceforth.
Detailed calculations and quotes can be referred to in Appendix F.
i. A house
Table 16. Financial analysis of proposed options for a house
For 1 house Window
replacement and
isolation
Heat pumps Solar PV (6
panels)
Solar PV (12
panels) ASHP GSHP
Investment (€) 4513 8060 2500 4800
Savings/year (€) 612 170 220 294 568
Payback (years) 8 >30 >30 13 11
NPV ( In € after 30
years)
11,123 - - 6,512 48,390
IRR 13.23% - - 6.63% 9%
Viable √ x x √ √
Applicable houses 33 97 97 2 23
5 The real rate of interest
- 1
-45-
ii. Apartment building 6:
Table 17. Financial analysis of proposed measures for the apartment building
Heat pump
Solar PV ASHP GSHP
Investment (€) 45,000 60,000 129,904
Savings/year (€)
(€)
2037 3385 12,455
Payback (years) 25 19 9
NPV( In € after 30 years) 1934 23,930 -
IRR 1.36% 3.31% -
Viable x √ √
iii. Theatre
Table 18. Financial analysis of proposed measures for the theatre
GSHP Solar PV
Investment (€) 75,000 118,527
Savings/year(€) 5,905 6,521
Payback (years) 14 14.6
NPV 39,275 -
IRR 5.92% -
Viable √ √
From the above tables, the following conclusions can be drawn:
- Insulation and window retrofits prove to be the most effective energy-efficiency measures.
Ensuring that a house is well-insulated and has high quality windows can result in
considerable savings.
- Solar panels (orientation and location permitting), can be quite profitable as well. With
subsidies, the profitability can go even higher, resulting in shorter payback times. Moreover,
solar panels for public buildings can be higher, based on negotiations with the energy
company.
- Prima facie, heat pumps do not seem to be a viable investment. This is due to the fact that
the savings in gas are off-set by the electricity costs of running the heat pump. thus, as
mentioned earlier, perhaps sizing the heat pump correctly will bring down the electricity
consumption, and thus boost savings.
6 Since the quotes for the solar PV for the apartment building and theatre sent by LENS B.V were of a preliminary nature, a basic financial analysis was done by the company. NPV and IRR calculations were not part of the quote.
-46-
8 Financial models
The previous chapter talks about the investment needed for large projects like this one. Here, the various
financial models that exist for renewable energy technology (RET) are analysed and discussed. Further,
based on previous examples of such projects, a financial model has been suggested for Waalwijk.
8.1 Barriers to implementation of RETs
Barriers to the implementation of RETs are multiple and have been documented and researched
extensively; they can broadly be classified (with examples) as [7]:
i. Market failures – Highly controlled market sector, restricted access to technology
ii. Market distortions – Taxes on RETs, favoring conventional energy
iii. Economic and financial barriers – High discount rates & paybacks, high investment costs, lack of
access to capital
iv. Institutional – Lack of institutions to disseminate information, lack of a regulatory framework, lack of
involvement of stakeholders in making decisions
v. Technical - Lack of codes and standards, system constraints, lack of entrepreneurs
vi. Social, cultural and behavioural – Lack of consumer and social acceptance for some RETs
Out of the numerous barriers listed above, those that have been identified as being most relevant to
Waalwijk are as follows:
i. High upfront cost and lack of capital
ii. Split incentive
iii. Low priority and lack of awareness
iv. Risks
Amongst the above, the problem of split incentive is the biggest hurdle for Waalwijk, as far as social
housing is concerned. The ‘split incentive’ refers to the situation where the investment is made by one
party, while the benefits are reaped by another. A classic example is that of rented houses. Since these
houses are owned by landlords or the housing corporation, only they are legally allowed to make major
modifications such as upgrading the building envelope or investing in a particular RET. However, if such
measures are taken, the benefits of these measures will be enjoyed by the tenant, since he/she will pay a
lower energy bill (energy bills are paid by the tenants themselves). Also, as per Dutch law, there is a ceiling
on the maximum rent that can be charged by social housing corporations. This makes the
landlord/housing corporation difficult for them to gain any sort of profit from such measures, which is
why it is rare to find old, rented houses that are as energy-efficient as the newer houses.
In addition, the barrier of high upfront cost is very much relevant to Waalwijk, as it is with most cases.
RETs generally require large investment costs, and have long payback times (greater than 10 years) [36] .
This is compounded by the fact that most RETs are still considered novel, and are perceived to be risky.
Though this is usually more applicable to large-scale energy projects, at a private level as well, people are
not very forthcoming to invest in RETs.
-47-
Low priority given to energy efficiency and savings is another major cause of RETs not taking off. The
chosen zone of Waalwijk mostly consists of middle-ages and elderly couples, whose children do not reside
with them. They spend most of their time indoors, with a lot of electricity consumption thanks to the
television, lights and other appliances. Also, being old, they want their houses to be as warm as possible.
This was noticed during visits to the houses in the zone – the living room temperatures were quite high,
and the houses were barely ventilated. The residents tried to keep their houses as warm as possible, since
the houses are not insulated and lose a lot of energy. Thus, for them comfort takes precedence over
energy savings.
However, it must also be noted that energy efficiency measures can have a ‘rebound effect’ – that is,
increased consumption due to the fact that energy efficiency measures have reduced the overall
expenditure of energy. This shall be discussed in detail in Chapter 10.
8.2 Types of financial models
Financial models for RETs are a method or a procedure of trying to address the barriers mentioned
above. They are generally policy instruments that can help communities overcome the most commonly
encountered barriers, and invest in RETs. Some are fairly common, such as loans, tax exemptions, while
there are also lesser-known ones such as leasing and ESCOs.
The following models have been identified as either being most common in the Netherlands, or as having
potential to be a sound financial model for RETs:
i. ESCOs
ii. Loans and mortgages
iii. Leasing
iv. On-bill financing
8.2.1 Integrated Energy Contracting Company (ESCo - IEC):
‘An Energy Service Company (ESCO) implements a customized service package (consisting of e.g. design, installation, (co-
)financing, operation & maintenance, optimization, fuel purchase, user motivation). It guarantees for the outcome and all-
inclusive costs of the services and takes over commercial as well as technical and operational risks over the project term of 10-
15 years’. [41]
An IEC ESCo is a company that acts as a general contractor for all renewable energy services. It takes
over the entire project of purchasing, installing and maintaining the energy-efficiency measures and RETs,
from start to end, and delivers the required output (heat and electricity) for a fixed price. Thus, the
building owner or client can outsource all activities related to the RET to the ESCo. This financial model
is now increasing in popularity, especially in Germany and Austria. [42]
The cost of procurement of energy (like gas, electricity, wood) is also included in the ESCo’s scope, and is
included in the fixed price to be paid by the client to the ESCo. Of course, the primary assumption is that,
in the long run, the savings due to the installation of the RETs and energy-efficiency measures will be
more than the fixed amount to be paid to the ESCo.
-48-
Additionally, it is also possible for the ESCo to arrange for capital. Of course, not all ESCos can do so,
but as they gain experience and execute more and more projects, banks will be more willing to finance
such projects, with the ESCo acting as the guarantor.
If it is not possible for the ESCo to gain finance, then the client would have to arrange for the capital (and
also repay it), and hand it over to the ESCo. The ESCo would be responsible for purchasing and installing
the equipment, and ensure savings for the client.
An overview of types of ESCos:
ESCos, used in the context of this report, are of the Integrated Energy Contracting (IEC) type. However,
traditionally, ESCOs are of two types:
- Energy Performance Contracting (EPC)
- Energy Savings Contracting (ESC)
It is only in the recent past that the newer model of an IEC has been piloted in Austria and Germany [42].
Let us now see what the major differences between these three models are [42]:
Table 19. EPC, ESC and IEC - a comparison
EPC ESC IEC
Business model
Procurement and
installation of only
energy efficiency
measures
Procurement,
installation and
maintenance of
renewable energy
technology
Procurement and
installation of energy
efficiency, as well as
renewable energy
measures
Measures
Insulation, window and
lighting retrofits,
upgradation of air-
conditioning services,
energy management
systems
Bio-gas/pellets/wood
chips CHPs, micro-
CHPs, solar PV, solar
thermal, geothermal
and heat pumps
Measures covered by
both EPC and ESC
Payment A certain percentage of
savings achieved
Price based on new
consumption (variable),
service cost (flat
rate)and capital cost (if
applicable)
Price based on new
consumption
(variable), service cost
(flat rate)and capital
cost (if applicable)
Energy
purchasing
responsibility
Client ESCo
ESCo
Savings
measured in
Nega-watt hours (NWh)
Mega-watt hours
(MWh)
NWh + MWh
-49-
The following figure gives a graphical representation of the models:
Figure 28. Comparison of different ESCos (Source: Wurtenberger, Blely et al., 2012)
-50-
Integrated energy Contracting (IEC) ESCos:
In this report, we shall be focusing on the applicability of an IEC ESCo. Figure 29 and Figure 30 show
how IEC arrangements can work [42]:
Most IEC projects are variations of the above model, as proposed by the
Practical example of an IEC project in the Austria: [43]
- Client: Landesimmobiliengesellschaft Steiermark (LIG) – State Real Estate company, Styria
- Location: The Retzhof (building complex with a mixture of different kinds of dwellings)
- Measures were a mix of energy efficiency (insulation and installation of a high-efficiency
boiler) and renewable energy measures (CHP)
- Project implemented in 2008 and was successful
- Figure 31 shows the agreement and flow of funds:
Loan All-inclusive fee
Principal + interest
Energy services
Client (building owner)
RET
ESCO Bank
Figure 29. IEC - financing by client (Adapted from: Wurtenberger, Blely et al., 2012)
Energy services
Repayment of loan
Service fees
Loan or lease
Client (building owner)
RET
Bank
ESCo
Figure 30. IEC - financing by ESCo (Adapted from: Wurtenberger, Blely et al., 2012)
-51-
Advantages of an IEC ESCo:
- IEC ESCo – ideal solution for social housing as well as private housing - Owners/ tenants pay for the output and results, not the input - Technical as well as financial risks outsourced - Capital can be arranged/facilitated by ESCo - Project tailored to the building owner’s needs - Onus on the ESCo to reduce input costs and increase output
Disadvantages of an IEC ESCo:
- Finance not always possible to be arranged by ESCo - Needs more initiative and incentives - Government impetus needed - Large projects preferred
8.2.2 Loans and mortgages:
Loans are an arrangement, whereby a financial institution, such a bank, lends money to an individual or an
organisation. The money is to be paid back within a certain time period, during which interest must also
be paid on the principal amount. This interest is calculated based on the rate offered by the bank, which
will slightly differ from bank to bank. Thus, the total money to be paid back to the bank includes the
principal and the interest.
‘A mortgage is a pledge of property to secure a payment of debt’ as defined in [44]. The debt is the loan that is given
to the owner of the property.
Examples of loan and mortgage schemes:
(a) Green Loans scheme [45]:
Green Loans is part of ALFAM Consumer Credit, a financial company in the Netherlands. It disburses
loans to private individuals for various energy-saving as well as renewable energy-generating measures, at
low rates. These loans are of two types:
Figure 31. Practical example of IEC contracting - Austria (Source: Bleyl, 2008)
-52-
- Green Loans EcoLening : This loan is for energy- efficiency measures like insulation, window retrofits,
waste heat recovery
- GreenLoans Lening – This type of loan covers solar PV, solar water heating and heat pumps
Other important points are:
- Loan amounts range from €5000 to €50,000;
- Borrowing rates ranging from 5.5 – 6.2%;
- Tax benefits are applicable;
- Conditions applicable are: Private home owner with a steady income, not self-employed and between
the ages of 20 to 70
(b) Green Funds scheme [46]:
The Green Scheme was launched in 1995, by the Dutch government, to stimulate private investment in
renewable energy. Following are the main features:
- By investing in this scheme, investors do not have to incur the 1.2% capital gains tax that is usually
charged on all investments. This is applicable for investments up to €55,000;
- The tax on the earnings from investing in the Green Funds is lower than usual – at a rate of 0.7%;
- The banks then lend money to individuals wishing to undertake renewable energy projects at a rate that
is 1% lower than the market rate.
8.2.3 Leasing:
‘Leasing is a temporary financing contract between a party (the ‘lessor’, such as a bank) - that provides an asset (such as a
renewable energy technology) to another party, the ‘lessee’, (such as a building owner) which wants to use the asset for a certain
period’ [42].
Leasing is similar to renting, in the sense that periodic payments are to be made, called the lease amount,
and the object leased is not owned 100% by the lessee. There are major differences – the most important
one being the question of ownership. In the case of leases, there are two kinds of ownership - the legal
ownership and the economic ownership. Legal ownership indicated whom the asset finally belongs to,
and all decisions regarding the asset are taken by the legal owner. Economic ownership involves taking
advantage of economic benefits such as tax deductions; but it also includes incurring associated financial
risks. Thus, the economic owner can show the asset in his/her balance sheet [41].
Types of leases:
There are two main types of leases which can be applied to RETs, depending on the ownership:
(a) Operational lease: In this type of lease, the lessor (the bank) has the economic ownership, while the
legal ownership is usually the lessee. Sometimes, at the end of the lease period, the economic
ownership can be transferred to the lessee [42].
(b) Financial lease: Here, the economic owner is the lessee.
-53-
Advantages of leasing [42] [41]:
- No high upfront investment required
- Only lease payment to be made from time to time
- Can take advantage of subsidies and tax deductions
- Leasing can be more flexible than a loan (shorter depreciation schemes and shorter terms)
- All kinds of building can be covered
Disadvantages of leasing [42] [41]:
- Leasing is not very common in case of RETs, compared to renting and selling;
- A major reason for this is that most leases are based on the condition that the equipment should not
be integrated with the building. It should be possible to un-assemble the equipment and re-assemble
them elsewhere, if required;
- Most RETs and energy efficiency measures are difficult to remove and re-install elsewhere. The only
notable exceptions are solar panels and ASHPs;
- It is observed that financial institutions are not generally in favour of leases, as it increases the
complexity of the arrangement, as compared to simple loans or renting
Leases and ESCOs:
- Leases can also be taken by ESCos, as part of the contract with the client;
- Since the equipment will be supplied by the bank/institute, the ESCo does not have to arrange for the
capital;
- ESCos usually prefer to have an operational lease, since the administrative obligations such as
accounting and other financial hassles can be avoided.
Examples of lease arrangements [42]:
(a) Simple lease between a building owner and a bank:
Periodic lease payments
Equipment/or capital
for lease
Client (building owner)
RET
Installer
Financial institution
(bank)
Figure 32. Simple lease arrangement (Adapted from: Wurtenberger, Blely et al., 2012)
-54-
(b) Leasing with an ESCo involved:
Practical example of a leasing ESCo model [47]:
- Client: City Hall of Sittard (the Netherlands)
- Essent as ESCo - Financing through ESCo, financial lease by ING Bank - Government subsidy - ESCo as general contractor, 15 year period - Problems: inefficient, outdated lighting, faulty cooling system, high energy expenditure - Savings : Heat = 293 MWh/a, electricity = 150 MWh/a - Extra savings – 50%/50% to ESCo and client
Service fee Periodic lease
payments
Equipment/or capital
for lease
Client (building owner)
RET
ESCO
Financial institution
(bank)
Figure 33. Leasing with the involvement of an ESCo (Adapted from: Wurtenberger, Blely et al., 2012)
Figure 34. Practical example of a leasing ESCo model - Sittard, the Netherlands (Source: Bleyl, 2010)
-55-
8.2.4 On-bill financing
On-bill financing is a relatively new concept of financing renewable energy projects. It is mostly prevalent
in the United States of America and Canada.
Concept of on-bill financing: [42]
- Utility companies invest in the renewable energy and energy efficiency measures for their customers;
- The cost for the measures must be repaid by the customer, as a part of the energy bill;
- The savings accrued must of course, be considerable compared to extra cost;
- The loan (as the payment is referred to) is on the electricity meter, and can be transferred to the next
resident/tenant
Advantages of on-bill financing:
- High investment cost is avoided, since the utility pays for the technology - Interest cost is usually lower than normal rates - Since the loan is based on the electricity meter, it gets transferred to the next person renting/buying
the house - Applicable to all kinds of buildings, which is a big advantage for a municipality - Utility guarantees performance, since it is responsible for energy savings - It is an opportunity for the utility to maintain/expand its customer count - Utility can ensure energy saving obligations (if applicable)
Disadvantages of on-bill financing:
- It has not yet implemented been in the Netherlands so far - Generally, this kind of financing is provided for projects with paybacks <10 years - Utilities might be reluctant to start a venture like this, since it involves high capital cost - The legal implications of issues like defaulting on loan payments, and wishing to change utilities are
still to be sorted out.
Periodic loan payments (on the
meter)
Client (building
owner/tenant)
Installer
Utility company
Figure 35. Principle of on-bill financing (Adapted from: Wurtenberger, Blely et al., 2012)
Service fee
Installation
Equipment/or capital
for equipment RET
-56-
8.2.5 The proposed financial model for Waalwijk
Based on the analysis in the earlier, a proposal for financing such a large scale renovation project in
Waalwijk has been detailed below. This model involves an ESCo, for obvious reasons such as ease of
implementation, outsourcing all technical aspects and a guaranteed savings. The contractual relationships
have been adapted on the two ESCo examples cited earlier.
Figure 36 shows the outline of this model:
The model would work as follows:
- The ESCo would arrange for 60 % of the capital from a bank at a low rate, with the municipality
acting as the guarantor;
- Casade, being the owner of the rented houses, would act as the co-financer, and put up the remaining
40% of the capital;
- The ESCo would be responsible for the complete project, including analysis, purchase of equipment,
installation and maintenance, over the lifetime of the project;
- The ESCo would charge the service fee (as explained in Table 19), based on agreed values from the
tenant – this would exclude the gas used for cooking (which would be paid directly to the utility);
- This payment is to be paid by whoever occupies the house; hence, Casade would also have to be part
of the understanding;
- The ESCo would be responsible for repayment of the loan over the lifetime.
Advantages of the proposal:
- The problem of split incentive can be addressed here, since Casade would make part of the
investment, and the tenant would be responsible for paying the ESCo;
- The ratio of investment is variable, and is to be agreed on by the concerned parties;
- The ESCo is the sole point of contact for the tenants for all issues related to the RETs and energy
efficiency measures;
- The ESCo also has to guarantee savings
Figure 36. Proposed financial model for rented houses in Waalwijk
-57-
Challenges:
- Finding an ESCo that is ready to undertake a large-scale project as this one;
- Convincing the tenants of the benefits of the project, against the additional cost to be incurred;
- Brokering an agreement between the ESCo, the tenants and Casade;
- Ensuring the ESCo meets its obligations.
The above model would also be applicable for the private houses and the theatre. In these cases, however,
there would be no co-financing – the ESCo would include the loan repayment in the agreed service fee.
-58-
9 Challenges and future work
The preceding chapters detail the energy scenario in the selected zone of Waalwijk, and discuss the
possible measures that can be implemented. However, since this was a time-bound project, with some
data not readily available, not all possibilities could be evaluated. This section mentions the challenges and
constraints faced, which can be remedied while furthering this project in the future.
Challenges:
- Data gathering from residents: Convincing residents to co-operate and provide access to data was
challenging. The process to get in touch with them took a long time;
- Lack of availability of data from commercial building: Several attempts were made to contact the
commercial building personnel; however, there was no initiative to direct us to the correct people.
- Inability to use public property as potential locations to generate power: There were a few public areas
like the bus station and an open parking lot in the zone, which could have been evaluated as well.
However, getting the approval of such changes would require a number of permissions, which would
take time, since it would mean getting all the parties to give their opinion;
- Contacting suppliers and manufacturers: Since the project demanded a real-time evaluation (as far as
was possible) of the measures to be taken, companies had to be contacted for quotes. This took time,
as most companies were either unwilling to quote or had other priorities. This time must be estimated
correctly;
- Availability of seasonal load profiles: Micro-CHPs were to be evaluated for the theatre – however,
load profiles were not available in order to estimate the potential. This option could also be analysed
for houses, provided average load profiles are made available for these houses.
The purpose of this report is to analyse how Waalwijk should proceed towards becoming a net-zero
energy city. The following steps can be used as a template to achieve this:
- Step 1: Ensure that insulation, window retrofits and lighting retrofits are installed in a pilot house and
study the change in energy consumption;
- Step 2: Renewable energy integration: Study the change in consumption. If the result is positive,
evaluate other technologies, like micro-CHPs, and other centralized sources of power generation such
as wind, a collective solar installation on open land, and biomass gasifier. Install the most suitable one.
- Step 3: Heat pumps to be evaluated in detail for the pilot houses;
- Step 4: Explore open public areas and commercial buildings as potential energy generation zones.
-59-
10 Conclusion
In conclusion, the findings of this exercise indicate that with respect to the measures suggested, the
chosen zone of Waalwijk does have potential to become a net-zero energy city; not wholly, but partially.
Energy efficiency measures show great promise. Making sure the houses are well insulated, and with good
quality windows, can reduce gas consumption by almost 40-50%. Lighting retrofits also have great
potential for electricity savings. The greater the number of lamps in a house, greater the savings.
Electricity generation from the de-centralized source of roof-top solar PV is limited – about 25% of the
total consumption of the zone. Heat can be supplied renewably almost completely (greater than 95%),
with some reservations regarding the economic viability of heat pumps.
However, factors other than those related to technology, also need to be considered. One major aspect
that decides the fate of such projects is the behaviour of the residents. How the residents respond to the
concept of energy savings and energy efficiency depends on a wide variety of reasons, as explained in [48].
Figure 37 shows the various factors, as documented in a research project bases in China:
For example, it has been noted in [49] and also practically on visits to the houses in Waalwijk, that the
behaviour of old people regarding thermal comfort and energy is different from that of younger people,
since they are more sensitive to temperature changes. This affects their energy consumption. In contrast,
energy usage (not behaviour) varies with the income level as well. More purchasing power means use of
electrical appliances that are efficient, which can reduce the consumption [50].
Numerous contradictions also abound when it comes to energy conservation and social behaviour. Most
commonly reported is the ‘rebound effect’. The rebound effect refers to a situation (for example), where
installation of energy efficiency measures (to check excess consumption) instead leads to higher
consumption. This is because the resident feels satisfied that he/she has taken energy conservation steps,
Figure 37. Framework for energy-saving behaviour in urban households in China (Source: Yue, Long, et al.)
-60-
and takes the liberty of using the saved utility even more that he/she did earlier. The savings in income
due to the implementation of such measures is used to pay for increased usage. This negates the point of
installing energy efficiency measures. This point is also noted in [49] – that energy efficiency measures
such as better insulation and heating systems in houses occupied by old people, lead to higher energy costs
than before. This is due to the fact that the upgrading the energy performance results in them using it
more liberally than before, to ensure more comfort.
Thus, the behaviour of the residents in the zone will also have to undergo a change, while implementing
such projects. Steps are already being taken in this direction by Casade – Casade offers free energy-related
advice to its tenants. Energy consultants advise interested tenants of the potential savings that can be
achieved by making small changes in their lifestyle and energy consumption behaviour. Changes include
turning the thermostat down by a couple of degrees in winter, using less water while showering, running
the washing machine & tumble dryer fewer times per week and avoiding putting the television &
computer on standby mode. Tenants are encouraged to make these changes and provide feedback on
energy expenditure after a certain period.
In summary, projects of this magnitude need efforts from all directions and aspects (technical, financial,
social and political) to make them successful. The municipality needs to work in close collaboration with
all the stakeholders in such a project – the residents, tenants, the employees of buildings, other authorities
and technology providers, to ensure that it meets its net-zero energy goal.
-61-
Works Cited
[1] S. Pless and P. Torcellini, "Net-zero energy buildings: A Classification System based on Renewable Energy
Supply Options," National Renewable Energy Laboratory, Colorado, June 2010.
[2] C. o. T. E. Communities, "Renewable Energy Road Map – Renewable Energies in the 21st century: building a
more sustainable future," Brussels, 2007.
[3] G. o. t. Netherlands, "Energy in the future," 2013. [Online]. Available:
http://www.government.nl/issues/energy/energy-in-the-future. [Accessed 10 August 2013].
[4] N. E. a. C. C. NL Agency, "Dutch Climate Policy: Local challenge supported by the national government,"
May 2010. [Online]. Available:
http://www.rwsleefomgeving.nl/publish/pages/92202/engelstalige_brochure_flok.pdf. [Accessed 10 August
2013].
[5] E. Commission, "DIRECTIVE 2010/31/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL on the energy performance of buildings," Official Journal of the European Union, 2010.
[6] N. Betlem, "Implementation of the EPBD in the Netherlands," Ministry of the Interrior and Kingdom
Relations, The Netherlands, 2010.
[7] J. Painuly, "Barriers to renewable energy penetration; a framework for analysis," Renewable Energy, vol. 24, pp.
73-89, 2001.
[8] H. Brouwers and A. Entrop, "New Triplet Visions on Sustainable Building," in The 2005 World Sustainable
Building Conference, Tokyo, 2005.
[9] M. Loomans, Passive design - Course notes: 7S815 Design of sustainable energy systems for the built environment,
Eindhoven: Eindhoven University of Technology, 2012.
[10] M. Loomans, Reader - Passive design strategies, Eindhoven: Eindhoven University of Technology, 2012.
[11] T. Mahlia, M. Said, H. Masjuki and M. Tamjis, "Cost-benefit analysis and emission reduction of lighting
retrofits in residential sector," Energy and Buildings, vol. 37, no. 2005, pp. 573-578, 2004.
[12] C. Washburn and L. Mueller, "CFL and LED Bulbs: Lighting for the Future," July 2010. [Online]. Available:
http://extension.usu.edu/files/publications/publication/FC_Energy_2010-02pr.pdf. [Accessed 10 August
2013].
[13] N. Khan and N. Abbas, "Comparative study of energy saving light sources," Renewable and Sustainable Energy
Reviews, vol. 15, pp. 296-309, 2011.
[14] U. D. o. Energy, "Energysavers.gov," December 2011. [Online]. Available:
http://energy.gov/sites/prod/files/2013/06/f2/energy_savers.pdf. [Accessed 10 August 2013].
[15] G. Lighting, "Lighting the future," September 2011. [Online]. Available:
http://www.gelighting.com/LightingWeb/de/images/Guide_to_changing_to_energy_efficient_lamps_Broc
hure_EN_tcm343-12666.pdf. [Accessed January 2013].
[16] G. Lighting, "Energy Saving on a new level," January 2011. [Online]. Available:
http://www.gelighting.com/LightingWeb/emea/images/LED_Retrofit_Lamps_Brochure_EN_tcm181-
12768.pdf. [Accessed January 2013].
-62-
[17] Eartheasy, "LED Light Bulbs: Comparison Charts," Eartheasy - Solutions for Sustainable Living, 2012.
[Online]. Available: http://eartheasy.com/live_led_bulbs_comparison.html. [Accessed February 2013].
[18] M. C. White, "Light Switch: Why You’ll Start Using LED Bulbs This Year," TIME Business and Money, 25
April 2013. [Online]. Available: http://business.time.com/2013/04/25/light-switch-why-youll-start-using-led-
bulbs-this-year/. [Accessed May 2013].
[19] B. Kiss and L. Neij, "The importance of learning when supporting emergent technologies for energy
efficiency—A case study on policy intervention for learning for the development of energy efficient windows
in Sweden," Energy Policy, vol. 39, pp. 6514-6524, (2011).
[20] G. Evola, G. Margani and L. Marletta, "Energy and cost evaluation of thermal bridge correction in
Mediterranean climate," Energy and Buildings, vol. 43, pp. 2385-2393, 2011.
[21] D. D. Chiras, "Energy-Efficient Design and Construction," in The Solar House: Passive Heating and Cooling,
Canada, Chelsea Green Publishing Company, 2002, pp. 81-82.
[22] C. Binggeli, "Thermal Comfort: Heating and Cooling Systems," in Building Systems for Interior Designers, New
Jersey, John Wiley & Sons, Inc., 2010, pp. 188-189.
[23] M. Centraal, "Dubbel glas en HR-glas," [Online]. Available: http://www.milieucentraal.nl/thema's/thema-
1/energie-besparen/isoleren-en-besparen/dubbel-glas-en-hr-glas/. [Accessed May 2013].
[24] I. E. Centre, "What is a U-value?," [Online]. Available: http://www.completehome.ie/files/whatisauvalue.pdf.
[Accessed May 2013].
[25] G. Courant, "Politiek achter meer windmolens bij Waalwijk," 5 November 2012. [Online]. Available:
http://groenecourant.nl/windenergie/politiek-achter-meer-windmolens-bij-waalwijk/. [Accessed 12 August
2013].
[26] S. Gebrezgabher, M. Meuwissen, B. Prins and A. Oude Lansink, "Economic analysis of anaerobic digestion—
A case of Green power biogas plant in The Netherlands," NJAS - Wageningen Journal of Life Sciences, vol. 57, no.
2, pp. 109-115, 2010.
[27] BlueGeneration, "BlueGen," 2011. [Online]. Available: http://www.bluegeneration.nl/?page_id=195.
[Accessed 15 May 2013].
[28] M. Boxwell, "The four configurations for solar power," in Solar Electricity Handbook: A Simple, Practical Guide to
Solar Energy, Warwickshire, Greenstream Publishing, 2011, pp. 15-17.
[29] G. Publishing, "Solar Electricty Handbook- Solar Calculator," 2013. [Online]. Available:
http://solarelectricityhandbook.com/solar-irradiance.html. [Accessed 22 May 2013].
[30] H. Harberlin, in Photovoltaics System Design and Practice, West Sussex, John Wiley & Sons, 2012.
[31] L. B.V, "Herman de Zonnestroom Verdeler," [Online]. Available:
http://www.zonnestroomverdeler.nl/nl_NL/.
[32] N. R. C. O. o. E. Efficiency, "Heating and Cooling with a Heat Pump," EnerGuide, Gatineau, 2004.
[33] NIBE, "NIBE F1245 Ground Source Heat Pump," NIBE Energy Systems AB, Markaryd, 2012.
[34] NIBE, "NIBE Split Air/water heat pump," NIBE Energy Systems, Markaryd, 2009.
[35] T. M.-g. P. -. E. R. D. F. a. E. Social, "Air Source Heat Pumps: Insulation, Heat Loss & Design," Dundee
College, Dundee, 2013.
-63-
[36] H. Romijn, Investment decisions for energy projects, Eindhoven: Eindhoven University of Technology., 2011.
[37] A. NL, "Subsidieregeling Zonnepanelen," Ministerie van Economische Zaken, 11 June 2012. [Online].
Available: http://www.agentschapnl.nl/programmas-regelingen/subsidieregeling-zonnepanelen. [Accessed July
2013].
[38] A. NL, "SDE+ 2013," February 2013. [Online]. Available:
https://www.agentschapnl.nl/sites/default/files/Digitale%20brochure%20SDE+%202013%20(kleurenversie)
%20def%20incl%20monitoring.pdf. [Accessed July 2013].
[39] S. Bank, "'Hypotheekrente vergelijken'," July 2013. [Online]. Available:
https://www.snsbank.nl/particulier/hypotheken/hypotheekrente.html?adtype=SEA.hypotheken.2013-
Generiek-Hypotheek%20Informatie-Rentevormen&adrecip=google. [Accessed August 2013].
[40] S. Netherlands, "Statistics Netherlands Press Release," 8 May 2013. [Online]. Available: http://www.cbs.nl/en-
GB/menu/themas/prijzen/publicaties/artikelen/archief/2013/2013-045-pb.htm. [Accessed June 2013].
[41] J. Bleyl and D. Schinnerl, "Opportunity Cost Tool, Comparison and Evaluation of Financing Options for
Energy-Contracting Projects," Graz Energy Agency, Graz, 2008.
[42] L. Wurtenberger, J. Bleyl, M. Menkveld, P. Vethman and X. van Tilburg, "Business models for renewable
energy in the built environment," Energy Research Centre, Petten, 2012.
[43] Bleyl-Androschin and Jan, "A new ESCo model to combine Energy Efficiency and Renewable Energy supply
in large buildings and Industry," Grazer Energieagentur GmbH, Graz, 2009.
[44] K. Sasidharan and A. Mathews, "Asset-Based Corporate Financial Services," in Financial Services and System, New
Delhi, Tata McGraw-Hill, 2008, p. 121.
[45] G. Loans, "Onze groene leningen," 2013. [Online]. Available: http://www.greenloans.nl/304/Groene-
Leningen.html. [Accessed July 2013].
[46] E. -. E.-i. A. Plan, "Promoting investment in sustainability: Green Funds," European Commission, 13
November 2012. [Online]. Available: http://ec.europa.eu/environment/ecoap/about-eco-
innovation/business-fundings/netherlands/13112012-promoting-investment-in-sustainability-green-
funds_en.htm. [Accessed June 2013].
[47] Bleyl-Androschin and Jan, "Competitive Energy Services," International Energy Agency, Graz, 2010.
[48] Y. Ting, L. Ruyin and C. Hong, "Factors influencing energy-saving behavior of urban households in Jiangsu
Province," Energy Policy, 2013.
[49] N. Hamza and R. Gilroy, "The challenge to UK energy policy:An ageing population perspective on energy,"
Energy Policy, vol. 39, pp. 782-789, 2011.
[50] K. Vringer, T. Aalbers and K. Blok, "Household energy requirement and value patterns," Energy Policy, vol. 35,
pp. 553-566, 2007.
[51] I. E. Agency, "Cross-country overview - Good Practices," in Energy Policlies of IEA countries, Paris, OECD
Publishing, 2005, p. 63.
[52] E. U. o. Technology, System Integration - Course 5EE40, Eindhoven: Electrical Energy Systems, 2012.
-64-
Appendix A: List of questions presented for data gathering
1) Energy consumption (electricity and gas) per month. If not, could you provide an approximate value of
the amount of electricity and gas consumed in the last year?
2) Lighting
- Approximate number and kind of lamps
- Rating/wattage of lamps
3) Is the house insulated? What is the type of insulation used in the house?
4) Kind of windows in the house – regular windows, double-glazed or triple-glazed windows?
5) What is heating system in the house? Specifications and capacity of boiler in use? Is there a special
cooling system?
6) How many people live in the house?
7) What is the area of the house? (In m2) Also the volume, if available (in m3)
8) What is the fuse rating of the incoming electrical power?
-65-
Appendix B: Savings due to lighting retrofits
Total savings for the zone:
Apartment House
Halogen LED replacement Incandescent Halogen
LED
replacement
Wattage (W) 50 20 7 4 40 10 9 4
Number of lamps 2 3 2 3 6 4 6 4
Hours of usage (hrs) 1825 1825 1825 1825 1825 1825 1825 1825
Current consumption
/lamp(kWh) 91.25 36.5 12.775 7.3 73 18.25 16.425 7.3
Total consumption 182.5 109.5 25.55 21.9 438 73 98.55 29.2
Cost(€/year) 40.15 24.09 5.621 4.818 96.36 16.06 21.681 6.424
Total cost 64.24 10.439 112.42 28.105
Savings/house/year
(€/year) 53.80 84.32
Savings for the
zone/year (€/year) 6994.13 10960.95
Electricity
savings/dwelling/year
(kWh) 244.55 383.25
Electricity savings for
all apartments and
houses in the
zone/year (kWh)
5135.55 49822.50
Total electricity
savings for the
zone/year 54,958 (kWh) ~ 55 MWh
-66-
Calculation of payback period and cumulative profits over the lifetime of the lamp:
Apartment
Year Initial
investment Recurring
costs Revenues Total cash
flow Cumulative cash flow
0 -100 -100
1 0 53.801 53.801 -46.199
2 0 53.801 53.801 7.602
3 0 53.801 53.801 61.403
4 0 53.801 53.801 115.204
5 0 53.801 53.801 169.005
6 0 53.801 53.801 222.806
7 0 53.801 53.801 276.607
8 0 53.801 53.801 330.408
9 0 53.801 53.801 384.209
10 0 53.801 53.801 438.01
11 0 53.801 53.801 491.811
12 0 53.801 53.801 545.612
13 0 53.801 53.801 599.413
14 0 53.801 53.801 653.214
15 0 53.801 53.801 707.015
16 0 53.801 53.801 760.816
17 0 53.801 53.801 814.617
18 0 53.801 53.801 868.418
19 0 53.801 53.801 922.219
20 0 53.801 53.801 976.02
Payback = 2 years
-67-
House
Year Initial
investment Recurring
costs Revenues
Total cash flow
Cumulative cash flow
0 -230 -230
1 0 84 84 -146
2 0 84 84 -61
3 0 84 84 23
4 0 84 84 107
5 0 84 84 192
6 0 84 84 276
7 0 84 84 360
8 0 84 84 445
9 0 84 84 529
10 0 84 84 613
11 0 84 84 697
12 0 84 84 782
13 0 84 84 866
14 0 84 84 950
15 0 84 84 1035
16 0 84 84 1119
17 0 84 84 1203
18 0 84 84 1288
19 0 84 84 1372
20 0 84 84 1456
Payback = 3 years
-68-
Appendix C: Savings due to window retrofits and insulation
U-values of various window coatings: Data:
Kind of window
coating
U-value (W/m2K) Average dimensions
of windows: 1.75m *0.75 m
Current double-glazed
windows 2.8 Number of
windows 8
HR 2 Total window area 10.5 m2
HR+ 1.6 Number of days
heating is required 273
HR++ 1.2 Hours/day 6
HR+++ 1 Total annual hours
of heating 1638 hrs
HR3 (triple glazed) 0.7
Formula: Transmission loss = U*A*(Ti-Ta) (W)
Average heat loss for each kind of window glazing in a year:
Month Jan Feb Mar Apr May Sep Oct Nov Dec Average heat
loss (kWh)
Temperature
outside - Ta (°C)
2.9 3.1 5.9 8.4 12.8 14.3 10.3 6.2 4
Internal temp -
Ti (°C)
21 21 21 21 21 21 21 21 21
Double glazed 532 526 444 370 241 197 315 435 500 648
HR 380 376 317 265 172 141 225 311 357 463
HR+ 304 301 254 212 138 113 180 249 286 370
HR++ 228 226 190 159 103 84 135 186 214 278
HR+++ 190 188 159 132 86 70 112 155 179 231
HR3 (triple
glazed)
133 132 111 93 60 49 79 109 125 162
-69-
Gas savings/year due to window retrofits:
Type of
window
U-
value
Transmission
loss
(MWh/year)
Transmission
loss (m3/year)
Gas
savings
(m3/year)
Gas
savings per
year in
(m3/m2)
Cost savings
(€/year)
Current
double-
glazed
windows
2.8 0.64 60.00
HR 2 0.46 42.86 17 1.6 11
HR+ 1.6 0.37 34.28 26 2.4 17
HR++ 1.2 0.27 25.71 34 3.3 22
HR+++ 1 0.23 21.43 39 3.7 25
HR3 (triple
glazed) 0.7 0.16 15.00 45 4.3 29
Gas savings/year due to insulation:
Surface to be insulated
Thickness (m) Area (m2)
Wall dimensions
Gas savings m3 /m2
Savings m3 gas /house
Total number of
houses
Total savings (m3 gas)
Floor - 42.7 6 256.2 130 33306
Cavity wall 0.05 58.65
9 527.85 130 68620.5
Roof 41.04 5 205.2 130 26676
Total 989.25 128,602.50
-70-
Appendix D: Solar PV output and inverters selected for houses
Annual output from one solar PV panel oriented due south (0° azimuth and at 60º inclination)
Month
Vinc (Angle -60°
(KWh/m2/day) Vtemp Vref
Generation losses factor
Inverter efficiency
Peak power (kWp)
No of days in
the month
Output from one
panel (kW)
Jan 1.29 1.02 0.95 0.90 0.97 0.25 31 8.46
Feb 2.11 1.02 0.95 0.90 0.97 0.25 27 12.05
Mar 3.04 0.95 0.95 0.90 0.97 0.25 31 18.56
Apr 4.01 0.88 0.95 0.90 0.97 0.25 30 21.95
May 4.88 0.87 0.95 0.90 0.97 0.25 31 27.29
Jun 4.74 0.87 0.95 0.90 0.97 0.25 30 25.65
Jul 4.71 0.86 0.95 0.90 0.97 0.25 31 26.04
Aug 4.49 0.86 0.95 0.90 0.97 0.25 31 24.82
Sep 3.35 0.89 0.95 0.90 0.97 0.25 30 18.55
Oct 2.31 0.98 0.95 0.90 0.97 0.25 31 14.55
Nov 1.42 1 0.95 0.90 0.97 0.25 30 8.83
Dec 1 1.02 0.95 0.90 0.97 0.25 31 6.56
Annual output 213.30
Annual output from one solar PV panel oriented due south (0° azimuth and at 45º inclination)
Month
Vinc (Angle -45°
(KWh/m2/day) Vtemp Vref
Generation losses factor
Inverter efficiency
Peak power (kWp)
No of days in
the month
Output from one
panel (kW)
Jan 1.4 1.02 0.95 0.9 0.97 0.25 31 9.18
Feb 2.21 1.02 0.95 0.9 0.97 0.25 27 12.62
Mar 3.04 0.95 0.95 0.9 0.97 0.25 31 18.56
Apr 3.84 0.88 0.95 0.9 0.97 0.25 30 21.02
May 4.5 0.87 0.95 0.9 0.97 0.25 31 25.16
Jun 4.3 0.87 0.95 0.9 0.97 0.25 30 23.27
Jul 4.3 0.86 0.95 0.9 0.97 0.25 31 23.77
Aug 4.24 0.86 0.95 0.9 0.97 0.25 31 23.44
Sep 3.3 0.89 0.95 0.9 0.97 0.25 30 18.27
Oct 2.4 0.98 0.95 0.9 0.97 0.25 31 15.12
Nov 1.52 1 0.95 0.9 0.97 0.25 30 9.45
Dec 1.08 1.02 0.95 0.9 0.97 0.25 31 7.08
Annual output (kWh) 206.94
-71-
Inverters required:
Street No. of houses No of
panels/house Peak power
(kWp) SMA Inverter
model
Touwerij 14 8 2 1 x SB 1600TL-
10
Victoriestraat 22 12 3 1 x SB 3000TL-
21
Schotsestraat 8 10 2.5 1 x SB 2100TL
Poolsestraat 1 6 1.5 1 x SB 1200
Poolsestraat 1 12 3.6
1 x SB 3000TL-21
Poolsestraat 1 6 1.5 1 x SB 1200
-72-
Appendix E: Quote from LENS B.V. for solar PV system on apartment and
theatre
Offer for the Herman system for apartment building:
Price list for the Herman system:
-73-
Price list for collective meter on apartment:
Installation requirements:
Guarantees and other costs for apartment:
-74-
LENS offer for theatre:
Price list for theatre:
Appendix F: Financial analysis
(1) For insulation and window retrofits:
Year Investment
costs (€)
Recurring
costs Revenues
Total cash
flows
Cumulative
cash flows (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
CF (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
CF
NPV IRR
0 -4514
-4514
-4514
-4514
1
0 612.00 612.00 -3901.55 1.01 0.99 605.53 1.13 0.88 540.49
2
0 612.00 612.00 -3289.55 1.02 0.98 599.12 1.28 0.78 477.34
3
0 612.00 612.00 -2677.55 1.03 0.97 592.79 1.45 0.69 421.57
4
0 612.00 612.00 -2065.55 1.04 0.96 586.52 1.64 0.61 372.31
5
0 612.00 612.00 -1453.55 1.05 0.95 580.31 1.86 0.54 328.81
6
0 612.00 612.00 -841.55 1.07 0.94 574.17 2.11 0.47 290.39
7
0 612.00 612.00 -229.55 1.08 0.93 568.10 2.39 0.42 256.46
8
0 612.00 612.00 382.45 1.09 0.92 562.09 2.70 0.37 226.50
9
0 612.00 612.00 994.45 1.10 0.91 556.15 3.06 0.33 200.03
10
0 612.00 612.00 1606.45 1.11 0.90 550.26 3.46 0.29 176.66
11
0 612.00 612.00 2218.45 1.12 0.89 544.44 3.92 0.25 156.02
12
0 612.00 612.00 2830.45 1.14 0.88 538.69 4.44 0.23 137.79
13
0 612.00 612.00 3442.45 1.15 0.87 532.99 5.03 0.20 121.69
14
0 612.00 612.00 4054.45 1.16 0.86 527.35 5.69 0.18 107.47
15
0 612.00 612.00 4666.45 1.17 0.85 521.77 6.45 0.16 94.91
-76-
16
0 612.00 612.00 5278.45 1.19 0.84 516.25 7.30 0.14 83.82
17
0 612.00 612.00 5890.45 1.20 0.83 510.79 8.27 0.12 74.03
18
0 612.00 612.00 6502.45 1.21 0.83 505.39 9.36 0.11 65.38
19
0 612.00 612.00 7114.45 1.22 0.82 500.05 10.60 0.09 57.74
20
0 612.00 612.00 7726.45 1.24 0.81 494.76 12.00 0.08 50.99
21
0 612.00 612.00 8338.45 1.25 0.80 489.52 13.59 0.07 45.04
22
0 612.00 612.00 8950.45 1.26 0.79 484.35 15.39 0.06 39.77
23
0 612.00 612.00 9562.45 1.28 0.78 479.22 17.42 0.06 35.13
24
0 612.00 612.00 10174.45 1.29 0.77 474.15 19.73 0.05 31.02
25
0 612.00 612.00 10786.45 1.30 0.77 469.14 22.34 0.04 27.40
26
0 612.00 612.00 11398.45 1.32 0.76 464.18 25.29 0.04 24.20
27
0 612.00 612.00 12010.45 1.33 0.75 459.27 28.64 0.03 21.37
28
0 612.00 612.00 12622.45 1.35 0.74 454.41 32.43 0.03 18.87
29
0 612.00 612.00 13234.45 1.36 0.73 449.60 36.72 0.03 16.67
30
0 612.00 612.00 13846.45 1.38 0.73 444.85 41.58 0.02 14.72
NPV 11,123
1
IRR 0.1323
Payback = 8 years NPV after 30 years = € 11,123 IRR = 13.23%
-77-
2) ASHP for houses:
Year Investment
costs
Recurring
costs Revenues
Total cash
flows
Cumulative
cash flows (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
CF
NPV
0 -8060
-8060
1 -8060
1
-100 170.00 70.00 -7990.00 1.01 0.99 -7905
2
-100 170.00 70.00 -7920.00 1.02 0.98 -7753
3
-100 170.00 70.00 -7850.00 1.03 0.97 -7604
4
-100 170.00 70.00 -7780.00 1.04 0.96 -7456
5
-100 170.00 70.00 -7710.00 1.05 0.95 -7311
6
-100 170.00 70.00 -7640.00 1.07 0.94 -7168
7
-100 170.00 70.00 -7570.00 1.08 0.93 -7027
8
-100 170.00 70.00 -7500.00 1.09 0.92 -6888
9
-100 170.00 70.00 -7430.00 1.10 0.91 -6752
10
-100 170.00 70.00 -7360.00 1.11 0.90 -6618
11
-100 170.00 70.00 -7290.00 1.12 0.89 -6485
12
-100 170.00 70.00 -7220.00 1.14 0.88 -6355
13
-100 170.00 70.00 -7150.00 1.15 0.87 -6227
14
-100 170.00 70.00 -7080.00 1.16 0.86 -6101
15
-100 170.00 70.00 -7010.00 1.17 0.85 -5977
16
-100 170.00 70.00 -6940.00 1.19 0.84 -5854
17
-100 170.00 70.00 -6870.00 1.20 0.83 -5734
18
-100 170.00 70.00 -6800.00 1.21 0.83 -5615
19
-100 170.00 70.00 -6730.00 1.22 0.82 -5499
20
-100 170.00 70.00 -6660.00 1.24 0.81 -5384
21
-100 170.00 70.00 -6590.00 1.25 0.80 -5271
22
-100 170.00 70.00 -6520.00 1.26 0.79 -5160
23
-100 170.00 70.00 -6450.00 1.28 0.78 -5051
24
-100 170.00 70.00 -6380.00 1.29 0.77 -4943
25
-100 170.00 70.00 -6310.00 1.30 0.77 -4837
-78-
26
-100 170.00 70.00 -6240.00 1.32 0.76 -4733
27
-100 170.00 70.00 -6170.00 1.33 0.75 -4630
28
-100 170.00 70.00 -6100.00 1.35 0.74 -4529
29
-100 170.00 70.00 -6030.00 1.36 0.73 -4430
30
-100 170.00 70.00 -5960.00 1.38 0.73 -4332
NPV -187,689
Payback = > 30 years
(3) Solar PV for house (6 panels):
Year Investment
costs
Recurring
costs Revenues
Total
cash
flows
Cumulative
cash flows (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
cash flow (1+i)^n
Discount
rate
(1/(1+i)^n)
NPV IRR
0 -2500
-2500
1 -2500
1 -2500
1
-100 294.00 194.00 -2306.00 1.01 0.99 -2282 1 1 182
2
-100 294.00 194.00 -2112.00 1.02 0.98 -2068 1 1 171
3
-100 294.00 194.00 -1918.00 1.03 0.97 -1858 1 1 160
4
-100 294.00 194.00 -1724.00 1.04 0.96 -1652 1 1 150
5
-100 294.00 194.00 -1530.00 1.05 0.95 -1451 1 1 141
6
-100 294.00 194.00 -1336.00 1.07 0.94 -1253 1 1 132
7
-100 294.00 194.00 -1142.00 1.08 0.93 -1060 2 1 124
8
-100 294.00 194.00 -948.00 1.09 0.92 -871 2 1 116
9
-100 294.00 194.00 -754.00 1.10 0.91 -685 2 1 109
10
-100 294.00 194.00 -560.00 1.11 0.90 -504 2 1 102
11
-100 294.00 194.00 -366.00 1.12 0.89 -326 2 0 96
12
-100 294.00 194.00 -172.00 1.14 0.88 -151 2 0 90
13
-100 294.00 194.00 22.00 1.15 0.87 19 2 0 84
-79-
14
-100 294.00 194.00 216.00 1.16 0.86 186 2 0 79
15
-100 294.00 194.00 410.00 1.17 0.85 350 3 0 74
16
-100 294.00 194.00 604.00 1.19 0.84 510 3 0 69
17
-100 294.00 194.00 798.00 1.20 0.83 666 3 0 65
18
-100 294.00 194.00 992.00 1.21 0.83 819 3 0 61
19
-100 294.00 194.00 1186.00 1.22 0.82 969 3 0 57
20
-100 294.00 194.00 1380.00 1.24 0.81 1116 4 0 54
21
-100 294.00 194.00 1574.00 1.25 0.80 1259 4 0 50
22
-100 294.00 194.00 1768.00 1.26 0.79 1399 4 0 47
23
-100 294.00 194.00 1962.00 1.28 0.78 1536 4 0 44
24
-100 294.00 194.00 2156.00 1.29 0.77 1670 5 0 42
25
-100 294.00 194.00 2350.00 1.30 0.77 1801 5 0 39
26
-100 294.00 194.00 2544.00 1.32 0.76 1930 5 0 37
27
-100 294.00 194.00 2738.00 1.33 0.75 2055 6 0 34
28
-100 294.00 194.00 2932.00 1.35 0.74 2177 6 0 32
29
-100 294.00 194.00 3126.00 1.36 0.73 2297 6 0 30
30
-100 294.00 194.00 3320.00 1.38 0.73 2413 7 0 28
NPV 6511.777
-0.394
IRR 0.0663
Payback = 13 years
NPV after 30 years = €6512
IRR = 6.63%
-80-
(4) Solar PV for house (12 panels):
Year Investment
costs
Recurring
costs Revenues
Total
cash
flows
Cumulative
cash flows (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
cash flow (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
cash flow
0 -4800
-4800
1 -4800
1 -4800
1
-100 568.00 468.00 -4332.00 1.01 0.99 -4286.18 1.09 0.92 429.28
2
-100 568.00 468.00 -3864.00 1.02 0.98 -3782.69 1.19 0.84 393.76
3
-100 568.00 468.00 -3396.00 1.03 0.97 -3289.38 1.30 0.77 361.18
4
-100 568.00 468.00 -2928.00 1.04 0.96 -2806.07 1.41 0.71 331.30
5
-100 568.00 468.00 -2460.00 1.05 0.95 -2332.63 1.54 0.65 303.89
6
-100 568.00 468.00 -1992.00 1.07 0.94 -1868.88 1.68 0.60 278.75
7
-100 568.00 468.00 -1524.00 1.08 0.93 -1414.68 1.83 0.55 255.68
8
-100 568.00 468.00 -1056.00 1.09 0.92 -969.88 2.00 0.50 234.53
9
-100 568.00 468.00 -588.00 1.10 0.91 -534.34 2.18 0.46 215.12
10
-100 568.00 468.00 -120.00 1.11 0.90 -107.90 2.37 0.42 197.33
11
-100 568.00 468.00 348.00 1.12 0.89 309.59 2.59 0.39 181.00
12
-100 568.00 468.00 816.00 1.14 0.88 718.25 2.82 0.35 166.02
13
-100 568.00 468.00 1284.00 1.15 0.87 1118.23 3.07 0.33 152.29
14
-100 568.00 468.00 1752.00 1.16 0.86 1509.67 3.35 0.30 139.69
15
-100 568.00 468.00 2220.00 1.17 0.85 1892.71 3.65 0.27 128.13
16
-100 568.00 468.00 2688.00 1.19 0.84 2267.47 3.98 0.25 117.53
17
-100 568.00 468.00 3156.00 1.20 0.83 2634.10 4.34 0.23 107.81
18
-100 568.00 468.00 3624.00 1.21 0.83 2992.71 4.73 0.21 98.89
19
-100 568.00 468.00 4092.00 1.22 0.82 3343.45 5.16 0.19 90.70
20
-100 568.00 468.00 4560.00 1.24 0.81 3686.43 5.63 0.18 83.20
21
-100 568.00 468.00 5028.00 1.25 0.80 4021.78 6.13 0.16 76.32
-81-
22
-100 568.00 468.00 5496.00 1.26 0.79 4349.62 6.69 0.15 70.00
23
-100 568.00 468.00 5964.00 1.28 0.78 4670.08 7.29 0.14 64.21
24
-100 568.00 468.00 6432.00 1.29 0.77 4983.28 7.95 0.13 58.90
25
-100 568.00 468.00 6900.00 1.30 0.77 5289.32 8.66 0.12 54.02
26
-100 568.00 468.00 7368.00 1.32 0.76 5588.34 9.44 0.11 49.55
27
-100 568.00 468.00 7836.00 1.33 0.75 5880.43 10.30 0.10 45.45
28
-100 568.00 468.00 8304.00 1.35 0.74 6165.73 11.22 0.09 41.69
29
-100 568.00 468.00 8772.00 1.36 0.73 6444.33 12.24 0.08 38.24
30
-100 568.00 468.00 9240.00 1.38 0.73 6716.35 13.34 0.07 35.08
NPV 48,389.21
-0.44
IRR 0.0902
Payback = 11 years NPV after 30 years = €48,390 IRR = 9.02%
(5) GSHP for apartment building:
Year Investment
costs
Recurring
costs Revenues
Total
cash
flows
Cumulative
cash flows (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
CF (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
CF
NPV IRR
0 -60000
-60000
-60000
-60000
1
-200 3385.00 3185.00 -56815.00 1.01 0.99 3151.31 1.03 0.97 3082.95
2
-200 3385.00 3185.00 -53630.00 1.02 0.98 3117.98 1.07 0.94 2984.18
3
-200 3385.00 3185.00 -50445.00 1.03 0.97 3085.00 1.10 0.91 2888.57
4
-200 3385.00 3185.00 -47260.00 1.04 0.96 3052.37 1.14 0.88 2796.02
5
-200 3385.00 3185.00 -44075.00 1.05 0.95 3020.09 1.18 0.85 2706.44
6
-200 3385.00 3185.00 -40890.00 1.07 0.94 2988.14 1.22 0.82 2619.72
7
-200 3385.00 3185.00 -37705.00 1.08 0.93 2956.54 1.26 0.80 2535.79
8
-200 3385.00 3185.00 -34520.00 1.09 0.92 2925.27 1.30 0.77 2454.54
-82-
9
-200 3385.00 3185.00 -31335.00 1.10 0.91 2894.33 1.34 0.75 2375.90
10
-200 3385.00 3185.00 -28150.00 1.11 0.90 2863.71 1.38 0.72 2299.78
11
-200 3385.00 3185.00 -24965.00 1.12 0.89 2833.43 1.43 0.70 2226.09
12
-200 3385.00 3185.00 -21780.00 1.14 0.88 2803.46 1.48 0.68 2154.77
13
-200 3385.00 3185.00 -18595.00 1.15 0.87 2773.80 1.53 0.65 2085.73
14
-200 3385.00 3185.00 -15410.00 1.16 0.86 2744.47 1.58 0.63 2018.91
15
-200 3385.00 3185.00 -12225.00 1.17 0.85 2715.44 1.63 0.61 1954.22
16
-200 3385.00 3185.00 -9040.00 1.19 0.84 2686.72 1.68 0.59 1891.61
17
-200 3385.00 3185.00 -5855.00 1.20 0.83 2658.30 1.74 0.57 1831.00
18
-200 3385.00 3185.00 -2670.00 1.21 0.83 2630.18 1.80 0.56 1772.34
19
-200 3385.00 3185.00 515.00 1.22 0.82 2602.36 1.86 0.54 1715.55
20
-200 3385.00 3185.00 3700.00 1.24 0.81 2574.84 1.92 0.52 1660.59
21
-200 3385.00 3185.00 6885.00 1.25 0.80 2547.61 1.98 0.50 1607.38
22
-200 3385.00 3185.00 10070.00 1.26 0.79 2520.66 2.05 0.49 1555.88
23
-200 3385.00 3185.00 13255.00 1.28 0.78 2494.00 2.11 0.47 1506.04
24
-200 3385.00 3185.00 16440.00 1.29 0.77 2467.62 2.18 0.46 1457.78
25
-200 3385.00 3185.00 19625.00 1.30 0.77 2441.52 2.26 0.44 1411.08
26
-200 3385.00 3185.00 22810.00 1.32 0.76 2415.70 2.33 0.43 1365.87
27
-200 3385.00 3185.00 25995.00 1.33 0.75 2390.15 2.41 0.42 1322.10
28
-200 3385.00 3185.00 29180.00 1.35 0.74 2364.87 2.49 0.40 1279.74
29
-200 3385.00 3185.00 32365.00 1.36 0.73 2339.85 2.57 0.39 1238.74
30
-200 3385.00 3185.00 35550.00 1.38 0.73 2315.10 2.66 0.38 1199.05
NPV 21,375
-2
IRR 0.0331
Payback = 19 years NPV after 30 years = €21,375 IRR = 3.31%
(6) ASHP for apartment building:
Year Investment
costs
Recurring
costs Revenues
Total cash
flows
Cumulative
cash flows (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
CF (1+i)^n
Discount
rate
(1/(1+i)^n)
Discounted
CF
NPV IRR
0 -45000
-45000
-45000.0
-45000
1
-200 2037.00 1837.00 -43163.00 1.01069 0.99 1817.6 1.01361 0.99 1812.3341
2
-200 2037.00 1837.00 -41326.00 1.021494 0.98 1798.3 1.02741 0.97 1787.9995
3
-200 2037.00 1837.00 -39489.00 1.032414 0.97 1779.3 1.04139 0.96 1763.9915
4
-200 2037.00 1837.00 -37652.00 1.043451 0.96 1760.5 1.05556 0.95 1740.306
5
-200 2037.00 1837.00 -35815.00 1.054605 0.95 1741.9 1.06993 0.93 1716.9384
6
-200 2037.00 1837.00 -33978.00 1.065879 0.94 1723.5 1.08449 0.92 1693.8847
7
-200 2037.00 1837.00 -32141.00 1.077273 0.93 1705.2 1.09925 0.91 1671.1404
8
-200 2037.00 1837.00 -30304.00 1.088789 0.92 1687.2 1.11421 0.90 1648.7016
9
-200 2037.00 1837.00 -28467.00 1.100428 0.91 1669.4 1.12937 0.89 1626.5641
10
-200 2037.00 1837.00 -26630.00 1.112192 0.90 1651.7 1.14475 0.87 1604.7238
11
-200 2037.00 1837.00 -24793.00 1.124081 0.89 1634.2 1.16033 0.86 1583.1768
12
-200 2037.00 1837.00 -22956.00 1.136097 0.88 1616.9 1.17612 0.85 1561.919
13
-200 2037.00 1837.00 -21119.00 1.148242 0.87 1599.8 1.19212 0.84 1540.9468
14
-200 2037.00 1837.00 -19282.00 1.160517 0.86 1582.9 1.20835 0.83 1520.2561
15
-200 2037.00 1837.00 -17445.00 1.172923 0.85 1566.2 1.22479 0.82 1499.8432
16
-200 2037.00 1837.00 -15608.00 1.185461 0.84 1549.6 1.24146 0.81 1479.7044
17
-200 2037.00 1837.00 -13771.00 1.198134 0.83 1533.2 1.25836 0.79 1459.8361
18
-200 2037.00 1837.00 -11934.00 1.210942 0.83 1517.0 1.27549 0.78 1440.2345
19
-200 2037.00 1837.00 -10097.00 1.223887 0.82 1501.0 1.29285 0.77 1420.8961
20
-200 2037.00 1837.00 -8260.00 1.23697 0.81 1485.1 1.31044 0.76 1401.8173
21
-200 2037.00 1837.00 -6423.00 1.250194 0.80 1469.4 1.32828 0.75 1382.9948
-84-
22
-200 2037.00 1837.00 -4586.00 1.263558 0.79 1453.8 1.34635 0.74 1364.425
23
-200 2037.00 1837.00 -2749.00 1.277066 0.78 1438.5 1.36468 0.73 1346.1045
24
-200 2037.00 1837.00 -912.00 1.290717 0.77 1423.2 1.38325 0.72 1328.03
25
-200 2037.00 1837.00 925.00 1.304515 0.77 1408.2 1.40208 0.71 1310.1982
26
-200 2037.00 1837.00 2762.00 1.31846 0.76 1393.3 1.42116 0.70 1292.6058
27
-200 2037.00 1837.00 4599.00 1.332555 0.75 1378.6 1.4405 0.69 1275.2497
28
-200 2037.00 1837.00 6436.00 1.3468 0.74 1364.0 1.46011 0.68 1258.1266
29
-200 2037.00 1837.00 8273.00 1.361197 0.73 1349.5 1.47998 0.68 1241.2334
30
-200 2037.00 1837.00 10110.00 1.375748 0.73 1335.3 1.50012 0.67 1224.567
NPV 1934
-1
IRR 0.01361
Payback = 25 years NPV after 30 years = € 1934 IRR = 1.36% (7) GSHP for theatre:
Year Investmen
t costs Recurring costs
Revenues Total cash flows
Cumulative cash flows
(1+i)^n
Discount rate
(1/(1+i)^n)
Discounted cash flow
(1+i)^n
Discount rate
(1/(1+i)^n)
Discounted cash flow
0 -75000
-75000
1 -75000
1 -75000
1
-500 5904.56 5404.56 -69595.44 1.01 0.99 -68859.33 1.06 0.94 5,102.30
2
-500 5904.56 5404.56 -64190.88 1.02 0.98 -62840.17 1.12 0.89 4,816.95
3
-500 5904.56 5404.56 -58786.31 1.03 0.97 -56940.64 1.19 0.84 4,547.55
4
-500 5904.56 5404.56 -53381.75 1.04 0.96 -51158.87 1.26 0.79 4,293.22
5
-500 5904.56 5404.56 -47977.19 1.05 0.95 -45493.04 1.33 0.75 4,053.11
6
-500 5904.56 5404.56 -42572.63 1.07 0.94 -39941.35 1.41 0.71 3,826.43
7
-500 5904.56 5404.56 -37168.07 1.08 0.93 -34502.00 1.50 0.67 3,612.43
8
-500 5904.56 5404.56 -31763.51 1.09 0.92 -29173.24 1.58 0.63 3,410.40
9
-500 5904.56 5404.56 -26358.94 1.10 0.91 -23953.35 1.68 0.60 3,219.67
-85-
10
-500 5904.56 5404.56 -20954.38 1.11 0.90 -18840.62 1.78 0.56 3,039.60
11
-500 5904.56 5404.56 -15549.82 1.12 0.89 -13833.36 1.88 0.53 2,869.61
12
-500 5904.56 5404.56 -10145.26 1.14 0.88 -8929.92 1.99 0.50 2,709.12
13
-500 5904.56 5404.56 -4740.70 1.15 0.87 -4128.66 2.11 0.47 2,557.61
14
-500 5904.56 5404.56 663.86 1.16 0.86 572.04 2.24 0.45 2,414.57
15
-500 5904.56 5404.56 6068.43 1.17 0.85 5173.76 2.37 0.42 2,279.53
16
-500 5904.56 5404.56 11472.99 1.19 0.84 9678.08 2.51 0.40 2,152.04
17
-500 5904.56 5404.56 16877.55 1.20 0.83 14086.53 2.66 0.38 2,031.68
18
-500 5904.56 5404.56 22282.11 1.21 0.83 18400.64 2.82 0.35 1,918.06
19
-500 5904.56 5404.56 27686.67 1.22 0.82 22621.92 2.98 0.34 1,810.79
20
-500 5904.56 5404.56 33091.24 1.24 0.81 26751.84 3.16 0.32 1,709.52
21
-500 5904.56 5404.56 38495.80 1.25 0.80 30791.87 3.35 0.30 1,613.91
22
-500 5904.56 5404.56 43900.36 1.26 0.79 34743.44 3.55 0.28 1,523.65
23
-500 5904.56 5404.56 49304.92 1.28 0.78 38607.98 3.76 0.27 1,438.43
24
-500 5904.56 5404.56 54709.48 1.29 0.77 42386.88 3.98 0.25 1,357.99
25
-500 5904.56 5404.56 60114.04 1.30 0.77 46081.52 4.22 0.24 1,282.04
26
-500 5904.56 5404.56 65518.61 1.32 0.76 49693.27 4.47 0.22 1,210.34
27
-500 5904.56 5404.56 70923.17 1.33 0.75 53223.46 4.73 0.21 1,142.65
28
-500 5904.56 5404.56 76327.73 1.35 0.74 56673.41 5.01 0.20 1,078.74
29
-500 5904.56 5404.56 81732.29 1.36 0.73 60044.43 5.31 0.19 1,018.41
30
-500 5904.56 5404.56 87136.85 1.38 0.73 63337.79 5.62 0.18 961.46
NPV 39274.31
1.79
IRR 0.05924
Payback = 14 years NPV after 30 years = € 39,274 IRR = 5.92%