Post on 21-Aug-2018
transcript
INSTALLATION, USE AND MAINTENANCE MANUAL
UK English
Snakky Max
DOC. NO. H 239U 00
EDITION 1 2004-07
DICHIARAZIONE DI CONFORMITA’
DECLARATION OF CONFORMITY
DÉCLARATION DE CONFORMITÉ
KONFORMITÄTSERKLÄRUNG
DECLARACIÓN DE CONFORMIDAD
DECLARAÇÃO DE CONFORMIDADE
VERKLARING VAN OVEREENSTEMMING
INTYG OM ÖVERENSSTÄMMELSE
OVERENSSTEMMELSESERKLÆRING
YHDENMUKAISUUSTODISTUS
Dichiara che la macchina descritta nella targhetta di identificazione, è conforme alle disposizioni legislative delle direttive:89/392, 89/336, 73/23 CEE e successive modifiche ed integrazioni.
Declares that the machine described in the identification plate conforms to the legislative directions of the directives: 89/392, 89/336, 73/23 EEC and further amendments and integrations.
Déclare que l’appareil décrit dans la plaque signalétique satisfait aux prescriptions des directives: 89/392, 89/336, 73/23 CEE et modifications/intégrations suivantes.
Erklärt, daß das im Typenschild beschriebene Gerät den EWG Richtlinien 89/392,89/336, 73/23 sowie den folgenden Änderungen/Ergänzungen entspricht.
Declara que la máquina descripta en la placa de identificación, resulta conforme a las disposiciones legislativas de lasdirectivas: 89/392, 89/336, 73/23 CEE y modificaciones y integraciones sucesivas.
Declara que o distribuidor descrita na chapa de identificação é conforme às disposições legislativas das directivas CEE89/392, 89/336 e 73/23 e sucessivas modificações e integrações.
Verklaart dat de op de identificatieplaat beschreven machine overeenstemt met de bepalingen van de EEG richtlijnen89/392, 89/336 en 73/23 en de daaropvolgende wijzigingen en aanvullingen.
Intygar att maskinen som beskrivs på identifieringsskylten överensstämmer med lagstiftningsföreskrifterna i direktiven:89/392, 89/336, 73/23 CEE och påföljande och kompletteringar.
Det erklæres herved, at automaten angivet på typeskiltet er i overensstemmelse med direktiverne89/392, 89/336 og 73/23 EU og de senere ændringer og tillæg.
Forsikrer under eget ansvar at apparatet som beskrives i identifikasjonsplaten, er i overensstemmelse med vilkårene iEU-direktivene 89/392, 89/336, 73/23 med endringer.
Vahvistaa, että arvokyltissä kuvattu laite vastaa EU-direktiivien 89/392, 89/336, 73/23 sekä niihin myöhemmin tehtyjenmuutosten määräyksiä.
Valbrembo, 03/05/2001
ANTONIO CAVO
C.E.O
1© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
TABLE OF CONTENTS
English
INTRODUCTION PAGE 2IDENTIFICATION OF THE VENDING MACHINE PAGE 2
IN THE EVENT OF FAILURES PAGE 2
TRANSPORT AND STORAGE PAGE 2
USING THE VENDING MACHINE PAGE 3
POSITIONING THE VENDING MACHINE PAGE 3
WARNING FOR INSTALLATION PAGE 3
PRECAUTIONS IN USING THE MACHINE PAGE 3
WARNING FOR SCRAPPING PAGE 3
TECHNICAL SPECIFICATIONS PAGE 4ACCESSORIES PAGE 4
POWER CONSUMPTION PAGE 4
CHANGEABLE COMBINATION LOCK PAGE 5
LOADING AND CLEANING PAGE 6MAIN SWITCH PAGE 6
CONFIGURING THE SPIRALS PAGE 6
HYGIENE AND CLEANING PAGE 7
LOADING PRODUCTS PAGE 7START-UP PAGE 8
NOISE LEVEL PAGE 8
INSTALLATION PAGE 9UNPACKING THE VENDING MACHINE PAGE 9
INSTALLING THE PAYMENT SYSTEM PAGE 9
CONNECTION TO THE POWER SUPPLY PAGE 10
CONTROLS AND INFORMATION PAGE 10INTERNAL COMPONENTS PAGE 11
MAIN SWITCH PAGE 11
DISPENSING COMPARTMENTMANUAL RELEASE PAGE 11
OPERATING MODES PAGE 12USER INTERFACE PAGE 12
DIRECT SELECTIONS PAGE 12
NORMAL OPERATING MODE PAGE 12
FILLER MENU PAGE 12STATISTICS PAGE 13
PRICES BY SINGLE SELECTIONS PAGE 13
CHANGE TUBES CONTROL PAGE 13
SPECIAL SELECTIONS PAGE 13
TEST PAGE 14
GSM PRE-ALARMS PAGE 14
EVADTS TRANSFER PAGE 14
TECHNICIAN MENU PAGE 15PRESENT FAILURES PAGE 16
PROGRAMMING THE PARAMETERS PAGE 17
STATISTICS PAGE 22
TEST PAGE 23
MACHINE INFORMATION PAGE 24
GSM PAGE 24
MAINTENANCE PAGE 25
PRINTED BOARD FUNCTIONSAND INDICATOR LAMPS PAGE 25
CONFIGURING THE BOARD PAGE 25
SOFTWARE UPDATE PAGE 25
CONFIGURING THE TRAYS PAGE 26PRODUCT SPACERS PAGE 26
PRODUCT EJECTOR PAGE 26
REPLACING THE SPIRALS PAGE 26
REMOVING THE TRAYS PAGE 26
CHANGING THE NUMBER OF TRAYS PAGE 27
CHANGING THE TRAY CONFIGURATION PAGE 27
POWER SUPPLY UNIT PAGE 28
ACCESS TO THE COOLING UNIT PAGE 28
PROGRAMMING MENU - SUMMARY PAGE 31
WIRING DIAGRAM PAGE 58
2© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
INTRODUCTION
This technical documentation is part and parcel of thevending machine and must always follow the machinein case it is moved or transfer of ownership, so as toallow consultation by different operators.
Before starting installation and using the machine, it is firstnecessary to carefully read and understand the instruc-tions contained in this manual, as they offer importantinformation on installation safety, operating instructionsand maintenance.
This manual is divided into three chapters.
The first chapter describes the loading and routine main-tenance operations which are carried out in areas of themachine accessible with simple use of the door key,without using any other tools.The second chapter contains the instructions for correctinstallation and all information necessary for optimum useof the machine.The third chapter describes maintenance operationswhich involve the use of tools to access potentially danger-ous areas.
The operations described in the second and thirdchapters must be carried out only by personnel whohave the specific knowledge of the machine function-ing from a point of view of electrical safety and healthregulations.
IDENTIFICATION OF THE VENDINGMACHINE AND ITS CHARACTERISTICS
Each machine is identified by its own serial number,indicated on the rating plate attached inside the cabinet onthe right side.This plate (see figure below) is the only one acknowledgedby the manufacturer as the identification of the apparatus,and carries all the data which readily and safely givetechnical information supplied by the manufacturer. It alsoassists in the spare parts management.
Absorbed power
Operating voltage
Model
Product code
Current
Frequency
Serial number
IN THE EVENT OF FAILURES
In most cases, any technical problems are corrected bysmall repair operations; however, before contacting themanufacturer we recommend that this manual be readcarefully.Should there be serious failures or malfunctions, contactthe following:
NECTA VENDING SOLUTIONS SpAVia Roma 2424030 ValbremboItaly - Tel. +39 - 035606111
TRANSPORT AND STORAGE
To prevent any damage, special care should be takenwhen loading or unloading the vending machine.The machine can be lifted by a motor-driven or manualforklift truck, and the forks are to be placed underneath themachine from the side clearly indicated by the symbol onthe cardboard package.
Do not:
- overturn the vending machine;
- drag the vending machine with ropes or similar;
- lift the vending machine by its sides;
- lift the vending machine with slings or ropes;
- shake the vending machine.
The machine should be stored in a dry room where thetemperature remains between 0°C and 40°C.Avoid stacking machines one on top of the other andalways keep it upright as indicated by the arrows on thepacking.
Refrigeration system class Type and amount of refrigerant
Type
Fig. 1
3© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
USING THE VENDING MACHINE FORPACKAGED PRODUCTS
A different sale price can be set for each product selectionby the machine electronic control. The various functionsare programmed through the selection keypad without anyneed for additional equipment.All models are equipped with variable configuration trays,adding or removing dividers, spirals and ratiomotors; there-fore the machine can be easily suited to specific needs.All trays are preset for the operation of up to 6 selections(maximum setting).The product compartments are equipped with independ-ent motors and spirals; each selection will continue itsoperation autonomously even if the other selections aredisconnected.
POSITIONING THE VENDING MACHINE
The vending machine is not suitable for outdoor installa-tion. It must be positioned in a dry room where the tempera-ture remains between 5°C and 32°C, and not where waterjets are used for cleaning (e.g. in large kitchens, etc.).To ensure correct machine operation we recommendinstalling the air baffle plate / spacer (80 mm) to the backof the machine (see Fig. 2).
Warning!
Incorrect ventilation may compromise the proper func-tioning of the cooling unit.
The machine should be positioned with a maximum incli-nation of 2°.If necessary provide proper levelling by way of the adjust-able feet included.
WARNING FOR INSTALLATION
The machine installation and the following mainte-nance operations should be carried out by qualifiedpersonnel only, who are trained in the correct use ofthe machine according to the standards in force.
The machine is sold without payment system, thereforethe installer of such a system is responsible for anydamage to the machine or to things and persons causedby faulty installation.
The integrity of the machine and compliance with thestandards of the relevant systems must be checked atleast once a year by qualified personnel.
PRECAUTIONS IN USING THE MACHINE
The following precautions will assist in protecting theenvironment:
- use biodegradable products only to clean the machine;
- adequately dispose of all containers of the productsused for loading and cleaning the machine;
- keep the machine away from heat sources;
- regularly check the condition of the door seal to limitany heat dispersion;
- limit as much as possible door opening time duringloading operations to avoid temperature increaseinside the cabinet and subsequent power consumption.
WARNING FOR SCRAPPING
Whenever the machine is to be scrapped, the laws in forceregarding environment protection should be strictly ob-served. More specifically:
- ferrous and plastic materials and the like are to bedisposed of in authorized areas only;
- insulating materials should be recovered by qualifiedcompanies;
- the gas inside the cooling unit, regardless of the type(see the identification plate), should be recovered byqualified companies by means of special equipment.
Fig. 2
1 - Securing holes2 - Spacer3 - Fastening screws
4© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
TECHNICAL SPECIFICATIONS
Power supply voltage 230 V~Power supply frequency 50 Hz
Absorbed power 560 W
Max. operating conditions:
Ambient temperature 32 °C
Relative humidity 65 %
Refrigeration system:
Compressor’s refrigeration output 620 W
Fan-forced evaporator
Programmable defrosting cycle
DIMENSIONS
Height 1830 mm
Width 740 mm
Depth 855 mm
Overall depth with door open 1350 mm
Weight 225 Kg
PAYMENT SYSTEMThe machine is supplied with all electrical prearrangementfor systems with Executive, BDV and MDB protocol, aswell as for installation of 24 V DC validators.Beside the coin mechanism housing, suitable space isprovided for the installation (optional) of the most widelyused payment systems.
SALES PRICES
A different programmable price can be set for each singleselection.
COIN BOXCover and lock are available as an optional feature.
CONTROLS AND SAFETY DEVICES
- Payment system compartment switch
- Timeout for power supply to dispensing motors
- Compressor overheating protection
- Line fuses
- Fuses on transformer primary and secondary windings
ACCESSORIES
A wide range of accessories can be installed on themachine, to vary its performance.The installation kits are supplied with their own installationand test instructions, which must be strictly observed toensure the machine safety.
Installation and the following testing operations mustbe carried out exclusively by personnel who have aspecific knowledge of the machine functions from apoint of view of electrical safety and health regula-tions.
POWER CONSUMPTION
The machine power consumption depends on many fac-tors, such as temperature and ventilation of the roomwhere it is installed, temperature of loaded products,internal temperature of the refrigerated box.Under average conditions, and namely:
- Ambient temperature: °C 20
- Refrigerated box temperature: °C 5
- temperature of loaded products(machine completely empty) °C 20
the following power consumption levels resulted:
- Hourly stand-by power consumption Wh 266
The above power consumption calculated from averagedata should only be taken as an indication.
Fig. 3
5© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
CHANGEABLE COMBINATION LOCK
Some machine models are fitted with a changeable com-bination lock.The lock is supplied with a silver colour key to be used fornormal opening and closing.The lock can be customised by means of a kit, available asaccessory, permitting changing of the lock combination.This kit includes a change key (black) for the current lockcombination as well as the change (gold) and use (silver)keys for the new combination.Sets of change and use keys with other combinations canbe supplied on request.Additional sets of use keys (silver) may be requested,indicating the combination stamped on the keys.Generally, only the use key (silver) is used, while thecombination change keys (gold) can be kept as spares.
Do not use the change key for normal opening, as itmay damage the lock.
Fig. 4
To change combination do as follows:
- open the machine door to avoid forcing the rotation;
- lightly lubricate the inside of the lock with a spray;
- insert the current change key (black) and rotate to thechange position (reference notch at 120°);
- remove the current change key and insert the changekey (gold) with the new combination;
- rotate to the close position (0°) and remove the changekey.
The lock will now have the new combination.
The keys with the old combination cannot be used forthe new combination.
6© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
Chapter 1LOADING AND CLEANING
MAIN SWITCH
When extracting the sliding compartment,a special switch(see Fig. 5) disconnects the power from the machineelectrical system to allow maintenance and cleaning op-erations in full safety.
The only parts that stay energised are those protectedby covers and carrying a plate with the warning “dis-connect the power before removing the cover”.
When dispensing sticks of candies or similar products, it ispossible to set the rotation of the spirals to 180° instead of360° for the 75 mm compartments and use a special righthand spiral fitted with a divider (see Fig. 7), doubling thecapacity of the compartments.
It is possible to insert a divider in the already installedspirals (see Fig. 7).As standard feature or using special kits, the machine canbe equipped with small compartments, suitable for dis-pensing cans, plastic bottles up to 69 mm dia., 0.2 litreTetra-Paks.The compartments equipped in this way can be recog-nised by the shape of the product support bracket (see Fig.8).Some bottle types can be dispensed without using thesupports.Most bottles can be dispensed without using any specialaccessories, loading the bottles up side down, so that the
CONFIGURING THE SPIRALS
According to the size of the products to be dispensed, eachmachine can be fitted with a variable number of trays(maximum 7), removable partitions and with dispensingspirals of different pitch.The spirals can be housed either in 152 mm compartments(two spirals, right-hand and left-hand, in each productholder) for large size products, or into 75 mm compart-ments (one right-hand spiral in each product holder) forsmall size products.
Fig. 5
1 - Door opening grip2 - Trays3 - Lock4 - Product passage photocells (optional)5 - Product dispensing compartment6 - Main switch7 - Sliding compartment
Fig. 6
1 - Tray2 - Mobile walls3 - Right-hand spiral4 - Left-hand spiral
Fig. 7
1 - 180° rotation spiral2 - DividerA - Spiral pitchB - Maximum product size
7© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
cap slides in the compartment channel.The spirals can be positioned with 22,5 degree steps bypulling them towards the front and rotating them in thedirection of ejection.Normally, the products can be dispensed without anyproblems when the spiral end is in the lower centre posi-tion.The maximum size (see Fig. 6) and the number of prod-ucts, the pitch and the direction of rotation of the spirals areshown in the following table.
The machine is supplied with a table indicating the opti-mum setting for the different product types.The configuration can be changed following the indicationsof the relevant chapter.
HYGIENE AND CLEANING
According to current health and safety regulations, theoperator of vending machines is responsible for theirhygiene and cleaning.The vending machine is not suitable for outdoor installa-tion. It must be positioned in a dry room where the tempera-ture remains between 5°C and 32°C, and not where waterjets are used for cleaning.This vending machine should only be used to sell anddispense packaged products that do not need refrigerationto be preserved.Strictly comply to the producer’s specifications regardingstorage method and expiry date for each product.
Any other use is unsuitable and thus potentially dan-gerous.
It is advisable to use sanitising products (chlorine baseddetergent or similar) to clean all surfaces even if not indirect contact with food.Some parts of the machine can be damaged by strongdetergents.
The manufacturer declines all responsibility for dam-age to persons caused by the non-compliance withcurrent regulations.At least every six months it is necessary to clean theventilation grilles of the cooling system using a vacuumcleaner or compressed air, doing as follows:
- with the vending machine disconnected from thepower supply, remove the front grille, completelyundoing the two screws;
- remove the air intake grille.
- after cleaning the grilles, reassemble everything in thereverse order.
A.mm
B.mm
°N
08 67 6
46 06 7
45 05 8
64 24 01
04 63 11
43 03 31
03 62 51
42 02 91
)°081(42 02 91+91
Under no circumstances should sprayed water beused.
Before any maintenance operation always switch themachine off.
The integrity of the machine and compliance with thestandards of the relevant systems must be checked atleast once a year by qualified personnel.
Fig. 8
1 - Tray groove2 - Product support
Fig. 9
1 - Air-intake grille2 - Front grille
8© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
LOADING PRODUCTS
- Remove one tray at a time, lifting it and pulling it pastthe retaining slide. The upper trays will tilt downwardsto facilitate loading.
Very thin products can be dispensed only using the specialspacer.
Fig. 11
- Load all products starting at the front, without insertingproducts with a temperature above 30°C, ensuring thatall spaces are filled. The bottom of the product mustrest at the bottom of the compartment with the labelfacing the window so that it can be identified.
All products should load easily, do not insert productswhich are too large for the space.
- Push in the trays completely, ensuring that they gopast the retaining slide.
Fig. 12
Fig. 10
The sealed end of bags may be caught under the spiral,preventing the free fall of the product.Fold the seal towards the front of the unit and upwardsbefore inserting the product in the spiral.
More fragile products must be placed on the lowertrays to prevent damage when they drop.
START-UP
Each time the machine is started the number of traysconnected to the system are checked by the electroniccontrols and indicated on the display.Also the number of actually connected compartments ischecked.The display will indicate in a sequence information regard-ing:
- software version
- presence of dispensing detection photocells
- number of trays and compartments
- presence of dispensing compartment lock device
- internal sensor temperature.
NOISE LEVEL
The continuous, weighted equivalent acoustic pressurelevel is below 70 dB.
1 - Product spacer2 - Brackets3 - Adjustment notches
9© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
Chapter 2INSTALLATION
The machine installation and the following mainte-nance operations should be carried out by qualifiedpersonnel only, who are trained in the correct use ofthe machine and are aware of the specific risks of suchoperations.
The machine is not suitable for outdoor installation, itmust be installed in a dry room where the temperatureremains between 5°C and 32°C.
It cannot be positioned where water jets are used forcleaning (e.g. in large kitchens, etc.).
The machine should be positioned with a maximuminclination of 2°.
The relative humidity must not exceed 65%.
UNPACKING THE VENDING MACHINE
After removing the packing, ensure that the machine isintact.If the vending machine is found to be damaged, immedi-ately inform the carrier and do not use the machine.
No packing elements (i.e. plastic bags, polystyrenefoam, nails, etc.) should be left within the reach ofchildren, as they are potentially dangerous.Packing materials must be disposed of in authorisedcontainers and the recyclable ones must be recovered byqualified companies.
If the vending machine had been laid down duringtransport, allow at least one hour before connecting itto the mains.
INSTALLING THE PAYMENT SYSTEM
The machine is sold without payment system, there-fore the installer of such a system has sole responsi-bility for any damage to the machine or to things andpersons caused by incorrect installation.
Install the coin mechanism paying attention, according tothe type used, to:
- choose the most suitable securing holes;
- loosening the fastening screw and adjusting the coinslot chute according to the coin mechanism opening;
- loosen the fastening screws and adjust the selectoropening lever;
- to aid installation the coin mechanism support platecan be lifted and rotated.
Fig. 13
1 - Coin chute fastening screw2 - Coin chute3 - Selector opening cam4 - Selector lever fastening screw5 - Coin mechanism securing holes6 - Coin mechanism compartment door7 - Coin mechanism8 - Coin slot chute9 - Coin return chute
10© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
CONNECTING THE MACHINE TO THEPOWER SUPPLY
The machine is designed to operate under a single-phase230 V~ voltage and is protected by T6.3 A fuses.Before making the connection, ensure that the ratingcorresponds to that of the power grid, and more specifi-cally:
- the supply voltage rating must be within the rangerecommended for the connection points;
- the main switch should be capable of withstanding thepeak load required, and at the same time ensureproper omni polar disconnection from the power gridwith an opening gap of the contacts of at least 3 mm.
The switch, the power outlet and the plug must belocated in an easily accessible position.The electrical safety of the machine is ensured only whenit is correctly earthed according to the safety standards inforce.
This fundamental safety requirement must be dulyverified, and if in doubt the system must be carefullytested by qualified technicians.
The power supply cable is of the type with a fixed plug. Anyreplacement of the power cable (see figure) should bemade by qualified and suitably trained personnel onlyusing cables type HO5 RN - F or HO5 V V-F or H07 RN-F with a 3x1-1.5 mm2 section.
CONTROLS AND INFORMATION
The user controls and information are located on theoutside of the sliding compartment (see Fig. 14).The credit and all function messages are indicated on thedisplay.
Do not use adapters, multiple sockets and/or exten-sions.
THE MANUFACTURER DECLINES ALL RESPONSI-BILITY FOR ANY DAMAGE CAUSED BY NON-COM-PLIANCE WITH THE ABOVE MENTIONED PRECAU-TIONS.
The keypad contains a series of numbered keys. To selecta product, key in the number corresponding to the desiredproduct.Key is used to cancel a selection already made.Keys and are not available to the user; they are usedonly for programming.
Fig. 14
1 - Lift cover2 - Cable clamp3 - Power supply cable
Fig. 1
1 - Door opening grip2 - Advertising spaces3 - Prearrangement for bill accepter4 - Prearrangement for key type payment systems5 - Display6 - Coin slot/return.7 - Selection keypad8 - Lock9 - Direct selection buttons10 - Coin return flap11 - Product flap12 - Removable ventilation grille13 - Glass front
11© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
MAIN SWITCH
The power supply unit (see Fig. 28) is fitted with a micro-switch that, when opening the sliding compartment, dis-connects the power from the machine electrical system,
except from the terminal board supporting the linecable, the line fuses and from the same switch area.
Before removing the cover from these parts (indicatedwith a specific plate) it is necessary to disconnect theexternal switch.
The power supply can be reconnected, if necessary, byinserting the special key supplied with the machine.
All operations which require the machine to be ener-gised with the door open must be carried out byqualified personnel who are aware of the specific risksof such condition.
DISPENSING COMPARTMENTMANUAL RELEASE
Some models are fitted with a lock device in the dispens-ing compartment that is released through electric controlwhen a selection is made (see compartment lock param-eters).Should for any reason be necessary to open the compart-ment without electric power, do as follows:
- remove the last tray;
- remove the anti-theft grille;
- manually operate the lock device.
INTERNAL COMPONENTS
The evaporator assembly mounted on the cabinet shelfcomprises two fans, the evaporator, the air duct and awater retaining tray placed under the evaporator.The C.P.U. board (central processing unit) fitted inside thepayment system compartment controls the different func-tions of the vending machine.
The cooling unit is located in the lower part of the cabinet.When removing all all covers of the ventilation grille, auniform temperature is achieved in the cabinet, se be-tween 5°C and 20°C.With the ventilation grille covers fitted, the temperature inthe cabined is diversified between the upper trays (12-15°C) and the lower trays with the holes on the duct open(5 -7°C).The cooling unit is defrosted automatically every 6 hours.In any case, the timing is programmable.The power supply unit, mounted in the lower section of thecabinet, contains the relay card which activates the com-pressor, the protection fuses and the switch on the pay-ment system door.
Fig. 15
1 - Product dispensing compartment housing2 - Cooling unit condenser3 - Cooling unit evaporator4 - Cold air flow grilles5 - Removable grille cover6 - Tray guides7 - Removable payment system compartment8 - C.P.U. board9 - Coin mechanism support10 - Product passage photocells11 - Power supply unit12 - Payment system compartment door switch
12© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
OPERATING MODES
The machine control software has three different functionlevels, which are:
- normal operation;
- filler menu;
- technician menu.
According to the operating mode, the display and keypadfunctions change as described in the following para-graphs.
USER INTERFACE
The interaction between system and operator happensthrough the following components:
- Liquid crystal display (LCD) 4 lines of 20 characters.
- External keypad configured via software with numerickeys from 0 to 9, having with the following functions inthe in the filler and technician menus:
DIRECT SELECTIONS
The vending machine can be fitted (as standard feature oras optional according to the model) with a 5-button keypadto which allocate a group of selection.After enabling the direct selection function, it will bepossible to allocate a group of selections to each key byspecifying the start and end numbers of the series.The selections, as long as in a sequence, can be also fromdifferent trays. The products are dispensed alternatingfrom each of the spirals that are grouped in a directselection.All selections belonging to the same group must have thesame price.For correct safety management of the selections it isadvisable that also a dispensing detection device beinstalled in the machine.
NORMAL OPERATING MODE
The machine is preset to “Normal operation” mode whenconnected to the power supply and the payment systemdoor is closed (see door switch - Fig. 24).The lighting is switched on and the messages for thecustomer are indicated on the display.
FILLER MENU
The machine is preset to “Filler menu” when pressing themenu access button (located on the CPU board - see Fig.17).The keys “ ” and “ ” scroll through the menu items, whichinclude:
“Statistics” Data reading and display
“Single Prices” Changing the price for oneselection
“Tubes control” Manual refill and release ofchange tubes
“Special selections” Virtual selectionsReturn of virtual priceTwo-motor selectionsPhotocell parameters
“Test” Test selectionMotor testAutotest
“GSM” Resetting pre-alarm counters
“EVADTS” Connection
If a menu is not enabled during programming, a title isdisplayed in the list but it cannot be accessed.
Price button
Key is used to access directly the price/selectioncombination of time band 0, if the function is enabled in the“Programming” menu.
Fig. 16
Numeric keys
1 to 7 are used to select directly a menu item by keying inthe corresponding number shown in the summary tablesincluded in the appendix to this manual.
Next menu key :" " is used to move to the next menu option.In the case of command management it varies the statusof Logical Data where required, or in the case of NumericData it writes the value 0.
Previous menu key :
" " is used to move to the next menu option.In the case of command management it varies the statusof Logical Data where required, or in the case of NumericData it writes the value 8.
Enter key :" " is used to move from a menu to a sub-menu or to entera command.
Exit key :
" " is used to move from a sub-menu to the higher levelmenu, or to exit from the current command.
13© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
STATISTICS
Data on the machine operations is stored in both generalcounters and relative counters, which can be reset withoutlosing total data.
PRINTConnect an RS232 serial printer having a Baud rate of9600, 8 data bit, no parity, 1 stop bit to the serial portlocated on the push button board to print all of thestatistics, and namely:
Total
1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;7 - dispensing compartment lock errors
Relative1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;7 - dispensing compartment lock errorsThe hardcopy printout will also contain the machine infor-mation, and namely:- date/time of print- machine name- software version- operator code- machine code- Installation date.To connect the printer, do as follows:
- press the confirm print button “ ”, displaying themessage “Confirm?”;
- connect the printer before confirming;
- press the confirm button “ ” to start printing.
DISPLAYWhen pressing the confirm button “ ” the data describedin the paragraph “Printing the statistics” is sequentiallydisplayed.
RESETTING THE RELATIVE STATISTICS
Statistics can be reset for relative counters globally (alltypes of data) or selectively for:- selections- failures- coin mechanism data- photocell errors- motor errors- dispensing compartment lock errorsPress the confirm button “ ”, and the message “Con-firm?” starts blinking.Press the confirm button “ ”, the message “Working” isdisplayed for a few seconds and all statistics are reset.
PRICES FOR SINGLE SELECTIONS
This function is used to change the sales price for eachselection according to the time band.Key is used to access directly the price/selectioncombination of time band 0, if the function is enabled in the“Programming” menu.
CHANGE TUBES CONTROL
By accessing the “Tube control” function the change tubescan be filled or released manually.Confirm refilling, and the display will indicate“Credit: ——” which is the value of money available inchange the tubes; insert the desired coin into the selectorand the display will indicate the value of money availablein the change tubes.When confirming releasing, it will be possible to decidewhich tube to release. Each time the confirm button “ ” ispressed, a coin is ejected from the active tube.
SPECIAL SELECTIONS
VIRTUAL SELECTIONS
This function is used to define a pair of selections that canbe sold at a price different from the sum of the twoselections, using a single selection number. 5 virtualselections can be programmed (80 to 84).
RETURN OF VIRTUAL PRICEThis function is used to define, in the event of failedsecond dispensing in a virtual selection, not to cash theprice of the second selection (only if an MDB paymentsystem or validator are used). With other payment sys-tems, it can be decided whether or not return the entireamount.
SELECTIONS WITH TWO MOTORS
In order to dispense long products, dividers can be fittedso that two motors are used for each single selection.With this function the operation of two motors can becombined, specifying the selection number of the secondmotor.The first motor number will be the selection number, whilethe selection number of the associated motor will remaindisabled.
Important notice!
After a failure to the motors of these selections, themachine configuration procedure in the “Spiral/Selec-tion” menu must be followed.
14© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
DISPENSING DETECTION
The vending machine can be fitted (as standard feature oras optional according to the model) with a device that, bymeans of photocells, detects the passage of dispensedproducts.This device permits, in the event of failed detection of thedispensed product:
- set a rotation time for the spiral beyond the limit switch,to overcome any jamming;
- return or not the paid amount;
- block further selections for the involved spiral.
TEST
SELECTIONS
This function is used to simulate the normal dispensing ofproducts without inserting any money to check the func-tioning of the spiral rotation by pressing the selectionbuttons.
MOTOR TEST
It activates all motors in a sequence, indicating on thedisplay the number of the involved selection.
AUTOTEST
A function to check, in a semiautomatic manner, thecorrect operation of some devices is implemented in thesoftware.Some checks occur automatically, others need the manualoperation of the monitored component; button “ ” ispressed to go to the next check.
The monitored devices are:
“Keypad”
Press the button requested on the display; if it workscorrectly the request for the next button is presented.
“Temperature”
The value of temperature detected by the probe is dis-played.In the event of disconnection the value -11.0 is displayed. In the event of a short-circuit the value 41.0 is displayed.“ ” to advance.
“Buzzer”
A series of sounds is emitted.
“Compressor”
The compressor is activated/deactivated using the “ ”and “ ” buttons.
“Selections”
All selections are activated in a sequence.
“Coin mechanisms”
Checking that communication with the coin mechanismtakes place correctly and which validator lines are aet asbeing active.
“Photocells”
If the product detection device is present, the light beamreading and interruption are checked.
“Disp compt lock”
If the device for locking the dispensing compartmentopening, use the “ ” and “ ” buttons to lock and unlock thecompartment opening.
“Direct keypad”
If fitted on the machine, the 5 buttons are checkedsequentially.Press the button requested on the display; if it workscorrectly the request for the next button is presented.
GSM PRE-ALARMS
The control software can send, via GSM modem, a signalindicating an “ending product” signal, when there is only acertain (programmable) number of pieces or grams ofpowder of a given product left. With this function thecounters that control the pre-alarms are reset.
EVADTS TRANSFER
When activating this function, the machine awaits theconnection with a device to acquire the EVADTS statis-tics.
15© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
TECHNICIAN MENU
Using the programming procedures described in thissection, it is possible to set all variables regarding ma-chine configuration.The machine is preset to “Technician menu” when press-ing button from the filler menu.
N.B. By pressing again the button from the technicianmenu, the machine will return to “Filler” mode.
The keys “ ” and “ ” scroll through the technician menuitems, which include:
Failures Read FailuresReset failuresMotor errorsMotors statusReset motor errors
Program param. Cash PricesCoin mechanisms
Decimal pointMaster/SlaveBonus
Spirals/select. SpiralsPhotocellsDisp comp lockCold parameters
Display LanguageUser messagesPromotional messagePersonalised stringsDisplay countersContrast control
Cold paramet. TemperatureEnable cold unitEnable Food controlTemperature log
Miscellaneous PasswordEnergy savingMenu maskingFluorescent lamps
switched offStatistics Display Partial
Total
Delete PartialTotal
Display relative PartialTotal
Delete relative PartialTotal
Display at start-up
Print relative PartialTotal
Delete PartialTotal
Test Test selectionsMotor testAutotest
Miscellaneous Machine info Installation dateMachine codeOperator code
Initialising
EVADTS Pass codeSecurity codeConnection
GSM Pin code
Pre-alarms ThresholdsCountersThreshold association
Number in bank
16© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
PRESENT FAILURES
READING
When the “Failure” function is displayed, press the con-firm button “ ” to display the present failures.If no failures are currently present, after pressing theconfirm button “ ” the message “End failures” will bedisplayed.The monitored failures are:
CompressorThe machine is locked if the compressor runs non-stop formore than 24 hours.
Coin mechanism
The machine is locked if it receives a pulse longer than 2seconds on a validator line or the communication with theserial coin mechanism does not take place for more than30 seconds (Executive protocol) or 75 seconds (BDVprotocol).
RAM DataOne or more areas of the RAM contain wrong data whichwas corrected with the default values.The machine will continue to function, but it would beadvisable to initialise as soon as possible.
Probe
The machine is locked after 5 minutes if the internaltemperature sensor is disconnected; the display will indi-cate a temperature of -11° C.The machine is locked after one hour if a sensor shortcircuit is detected; in this case the display will indicate atemperature of +41° C.
Motor errorsWith this function the failed motors are displayed forapproximately 1 second.Scrolling through all failed motors is automatic.
Note:
By restarting the machine any blocked motors are de-tected as not present.
Dispensing compartment lockWhen the function “unlock compartment with dispensing”and the parameter “out of service if open” are active, themachine will lock if the locking device of the dispensingcompartment remains blocked when closed or it does notclose within the programmed time.
Motors status
This function is used to read the last failure that occurredin each spiral, even if the machine configuration has anempty position.A motor can be in one of the following conditions:
- motor functioning;
- motor not present; when the motor is not detected atmachine start-up.
- motor disconnected; when a motor detected at ma-chine start-up is not detected during a selection.
- motor blocked; when the positioning button is notoperated within the “timeout”.
- empty spiral; when, with the dispensing control in-stalled, no dispensed product is detected.
Note:
By restarting the machine any motors with errors aredetected as not present.
RESETBy confirming this function all current failures will be reset.
17© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
PROGRAMMING PARAMETERS
CASH
This set of functions controls all parameters regarding thepayment systems and the sales prices.
SELECTION PRICESFour different prices can be set for each selection accord-ing to the programmed time bands for when the time tableoption is set.For each of the 4 time bands prices (0 to 65,535) can beprogrammed globally (same price for all selections) or forthe single selections.Should the majority of products be sold at the same price,it will be convenient to set the price globally and thenchange the figure of the selections with different prices.
TIME BANDS
Four programmable time bands are provided for sellingproducts at different prices.The time periods are programmable for beginning andend time by hours (00 to 23) and minutes (00 to 59).If the values for start and end of the time band are set to00.00 the time period is disabled.The reference time is kept by an internal clock, program-mable as:day/month/year week-day 1-7and thenhour/minutes/seconds.
COIN MECHANISMS
It is possible to decide which of the payment systemprotocols available are to be enabled for the functions.The available payment systems are:
- Executive
- Validators
- BDV
- MDB
By selecting one of the systems it is possible to control itsfunctions.
EXECUTIVE
The following payments systems are available for theExecutive system:
- Standard
- Price Holding
- Coges
- U-Key
VALIDATORSWhen the “Validat. Lines” (line setting) function of the“technician” menu is displayed, the value of the 6 validatorcoin lines, A to F, can be changed.
BDVThe BDV protocol menus are used for defining the follow-ing functions:
Type of vending
Setting the operating mode for multiple or single dispens-ing. With multiple dispensing, the change is not automati-cally returned after a successful selection, however thecredit is available for further selections. When pressingthe coin return button, the available credit is returned if itsvalue is lower than the maximum change value.
Change controlThis function enables/disables the return of credit if noselections are made.If enabled, this function allows the return of coins even ifthe first selection was not dispensed.If however a selection fails for any reason, the change willbe returned if requested.Maximum creditThis function is used to define the maximum acceptedcredit.Maximum changeIt is possible to set a limit to the total amount of changereturned by the coin mechanism when pressing the coinreturn button or after a single dispensing serving.Any credit exceeding the amount programmed with thisfunction will be cashed.
Accepted coins
It is possible to define which, among the coins recognisedby the validator, are to be accepted.Check the label on the coin mechanism for the correct cointo value matching, indicating the position of the coins.
Not accepted coins
This function programs the rejection of coins when in“exact amount” mode.Check the label on the coin mechanism for the correct cointo value matching, indicating the position of the coins.
Dispensing buttons
This function enables or not the buttons on the coinmechanism used to release the coins in the change returntubes.
Value of “exact amount”
This value defines the combination of empty coin tubes,setting the coin mechanism in “exact amount” mode. Thepossible combinations of empty coin tubes are indicatedbelow.
18© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
For greater simplicity, the combination is described withreference to tubes A, B and C, where tube A receives thelower value coins and tube C the greater value coins.
0 = A or (B and C)1 = A and B and C2 = A and B only3 = A and (B or C)4 = A only5 = A or B (default) only6 = A or B or C7 = A or B only8 = A or C only9 = B and C only10 = B only11 = B or C only12 = C only
C.P.C. device
It dialogues with the coin mechanism if devices areinstalled or removed from the serial interface (C.P.C.-typedevices - the monitoring unit is always enabled by default).
Minimum level of tubes
It brings forward the “Insert exact amount” message forthe user, by adding a number of coins between 0 and 15to the programmed number of coins, to set the “full changetubes” status.
Free Vend VMC
Most payment systems with the BDV protocol control thefree vend function.However, there are some payment systems without suchfunction.In this case, if free selections are to be dispensed, freevending must be enabled with VMC (vending machinecontrol, enabled by default) and the price of the selectionsmust be set to zero.
MDBThe MDB protocol menus are used for defining the follow-ing functions:
Type of vending
Setting the operating mode for multiple or single dispens-ing. With multiple dispensing, the change is not automati-cally returned after a successful selection, however thecredit is available for further selections. When pressingthe coin return button (if the function is enabled), theavailable credit is returned up to the maximum changevalue.
Change controlTo enable/disable the operation of the coin return button.Maximum creditThis function is used to define the maximum acceptedcredit.Maximum changeIt is possible to set a limit to the total amount of changereturned by the coin mechanism when pressing the coinreturn button or after a single dispensing serving.Any credit exceeding the amount programmed with thisfunction will be cashed.
Accepted coins
It is possible to define which, among the coins recognisedby the validator, are to be accepted when the changetubes are full.Check the coin mechanism configuration for the correctcoin to value matching.
Returned coinsIt is possible to define which, among the coins available inthe tubes, are to be used for returning the change. Thisparameter is active only with coin mechanisms that do notautomatically control the choice of tube to be used (Autochanger payout).Check the coin mechanism configuration for the correctcoin to value matching.
Accepted bills
It is possible to define which, among the bills recognisedby the reader, are to be accepted.Check the reader configuration for the correct bill to valuematching.
Minimum level of tubesThis function is used for setting the number of coins (0 to15) to determine the status of full change tubes and the“Insert exact amount” message for the user.
Accepted coins with “exact amount”
It is possible to define which, among the coins recognisedby the validator, are to be accepted when the machine isin the “exact amount” condition.Check the coin mechanism configuration for the correctcoin to value matching.
Accepted bills with “exact amount”It is possible to define which, among the bills recognisedby the accepter, are to be accepted when the machine isin the “exact amount” condition.Check the accepter’s configuration for the correct bill tovalue matching.
COMMON FUNCTIONS
Other menus are available, common to the three protocols,used for defining the following functions:
IMMEDIATE CHANGENormally, the amount of credit inserted for a selection iscashed after the machine sends the message “Selectionsuccessful”.When this function is enabled, disabled by default, thecash message is sent at the beginning of dispensing.
DECIMAL POINT
Press the confirm button “ ” to display the position of thedecimal point, i.e.:
0 decimal point disabled
1 XXX.X
2 XX.XX
3 X.XXX
Press the confirm button “ ”, these values will startblinking and can then be modified as necessary.
19© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
MASTER/SLAVEThe machine control system is pre-arranged for the con-nection in a bank of vending machines using special kits.This permits the use of a single payment system for moremachines.In the event of installation in a bank of machines, it can beconfigured a “Master”, i.e. having control over the secondmachine, or as “Slave”, i.e. leaving the control to the othermachine.Although the machine can be used in either the master orslave functions, it is advisable to use the Snakky asmaster, thus taking advantage of the central push-buttonpanel and the easier opening of the doors.The master/slave function is not enabled by default.To enable the function, it must be defined which machineis master and which one is slave in the software of both theSnakky and the Astro.If an Executive payment system in “Price Holding” modeis set in the master machine, the information must be setalso in the software of the slave machine.The payment system of the slave machine must always bedefined as “validator”.In the event of failed electrical connection, both machineswill display the message “failed communication”.
COMBINED SELECTIONS
A combined selection is intended as the association of twoselections, one from the Snakky and one from the Astro,to the same number (85 to 89) sold at a single price.Since a numeric keypad is required for setting and control-ling the combined selections, the relevant menu is in-cluded only in the software of the Snakky permitting thecombination of a selection from the keypad (10 to 79) witha direct selection (01 to 18).Combined selections can be used either with the Snakkyas master and Astro as slave (recommended configura-tion) or vice versa. If one of the two selections is notavailable, the combined selection is not dispensed. If theimmediate change option is not activated on the mastermachine, and the first selection fails, the whole amount isreturned. If the second selection fails, it will be possible todecide whether to keep or return the entire amount byactivating/deactivating the “Virtual change return” option.
FREE VEND BONUS
This function, compatibly with the national laws, permitsthe dispensing of a free product every certain programma-ble number of sold selections. In any case the freeselection is random within the programmed number. Themachine emits an intermittent sound signal and the dis-play indicates the message “FREE selection”.
SPIRALS/SELECTIONS
This set of functions is used to define the selection controlparameters.
MACHINE CONFIGURATION
This function is used to detect and store the number andposition of the trays and of the selection motors.
VIRTUAL SELECTIONS
This function is used to define a pair of selections that canbe sold at a price different from the sum of the twoselections, using a single selection number. 5 virtualselections can be programmed (80 to 84).
RETURN OF VIRTUAL PRICE
This function is used to define, in the event of failedsecond dispensing in a virtual selection, not to cash theprice of the second selection (only if an MDB paymentsystem or validator are used). With other payment sys-tems, it can be decided whether or not return the entireamount.
SELECTIONS WITH TWO MOTORS
In order to dispense long products, dividers can be fittedso that two motors are used for each single selection.With this function the operation of two motors can becombined, specifying the selection number of the secondmotor.The first motor number will be the selection number, whilethe selection number of the associated motor will remaindisabled.
Important notice!
After a failure to the motors of these selections, themachine configuration procedure in the “Spiral/Selec-tion” menu must be followed.
20© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
ROTATION SELECTIONS
With this function it is possible to create 7 groups of spiralswith the same selection number that are activated byrotation, to increase the autonomy of the same productand make dispensing uniform.The grouped spirals of a single selection must be next toeach other.All selections belonging to the same group must have thesame price.For correct safety management of the selections it isadvisable that also a dispensing detection device beinstalled in the machine.
PRODUCT CODEThis function is used for assigning a 4-digit identificationcode to each selection for processing the statistics.
DIRECT SELECTIONS
The vending machine can be fitted (as standard feature oras optional according to the model) with a 5-button keypadto which allocate a group of selection.After enabling the direct selection function,it will be possible to allocate a group of selections to eachkey by specifying the start and end numbers of the series.The selections, as long as in a sequence, can be also fromdifferent trays. The products are dispensed alternatingfrom each of the spirals that are grouped in a directselection.All selections belonging to the same group must have thesame price.For correct safety management of the selections it isadvisable that also a dispensing detection device beinstalled in the machine.
PHOTOCELL PARAMETERSThe vending machine can be fitted (as standard feature oras optional according to the model) with a device that, bymeans of photocells, detects the passage of dispensedproducts.When this device is installed, the following can be moni-tored:
- Error before dispensing; when at the selection start thephotocell beam is not read.
- Error after dispensing; when the motor fails duringdispensing.
- Error for no product; when the device does not detectthe passage of a product during dispensing.
In these cases the machine can be programmed to:
- set a rotation time for each spiral for settling beyondthe normal rotation;
- return or not the paid amount;
- block further selections for the involved spiral.
DISPENSING COMPARTMENT LOCK PARAMETERS
The dispensing compartment can be fitted (as standardfeature or as optional according to the model) with a lockdevice.This function is used for deciding whether leaving thedispensing compartment “always free” or “unlock it withdispensing”.In “unlock with dispensing” mode the dispensing compart-ment hatch is unlocked only for a certain period of time,programmable at between 1 and 10 minutes, after eachproduct selection. In this case it is possible to enable thefunction that places the vending machine out of service fora certain period of time, programmable at between 1 and10 minutes, if the dispensing compartment hatch staysopen.The machine is placed out of service if the lock device isalways closed during dispensing.
REFRIGERATION PARAMETERS
The operation of the refrigeration system can be pro-grammed for the following functions.
TEMPERATURE
The machine internal temperature during normal opera-tion can be set directly in °C (5° to 20°C, 8°C by default).The temperature differential deviation defined with theprevious function for starting/stopping the cooling unit is2°C.
DEFROSTING
This function allows for a defrosting cycle (switching thecooling unit off, regardless of the temperature) of 20minutes. The time interval between cycles can be pro-grammed from 0 to 99 hours (set to 6 hours by default); thetime interval will be determined according to the relativehumidity and the frequency of door openings.With the timing set to 0 the function is disabled.
ENABLE COLD UNIT
The cooling unit operation can be disabled. The changewill apply when restarting the machine.
FOOD CONTROLThis function is not active in this model.
TEMPERATURE LOG
The internal temperature is stored every 10 minutes.With this function, it is possible to read the date, time andstored temperature.
21© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
DISPLAY
This set of functions is used to manage the messagesindicated on the external display.
LANGUAGE
There is an option of language, selected among theavailable ones, to be used for the messages on thedisplay.
DISPLAYING MESSAGES FOR THE USERIt is possible to choose the kind of information to beindicated on the display during normal operation.The following information can be displayed:
- Internal temperature
- Time
It is possible to choose the language for the displayedmessages.
PROMOTIONAL MESSAGE
EnableWhen in this menu, press the confirm button “ ” to displaythe status of the message (enabled or disabled). Thestatus can then be changed using the “ ” and “ ” buttons.
Setting
The 2-line message can be written using the “ ” and “ ”buttons to scroll through the available characters.Press the confirm button “ ”, the first character will startblinking and can be modified.The message is stored by pressing button “ ”.
CUSTOMISING THE MESSAGESThe machine uses standard messages to give informa-tion to the user during normal operation (e.g. “Ready”,“Take” etc.). When this function is enabled, the messagecan be changed in the same manner as setting thepromotional message. Changes are stored as copies ofthe standard messages.Therefore, if this function is disabled, the standard mes-sages will be displayed again, but the changed messagesare still stored.
DISPLAY THE SELECTION COUNTERS
This function is used to enable/disable the display of thetotal number of sales since the last statistic reset, duringthe start-up phase of the machine.
LCD CONTRAST CONTROLThis function is used for adjusting the display contrastfrom 5% to 99% (default).
MISCELLANEOUS
This set of functions contains some sub-menus, used lessfrequently, which permit control of the functions describedbelow.
PASSWORD
ENABLING THE PASSWORD
This function is used to enable the option of requesting thepassword to access the technician menu; the passwordrequest is disabled by default.
ENTERING THE PASSWORD
It is a 5-digit numeric code which is required to access thetechnician menu.The default value of this code is set to 00000.
DISPLAYING THE FILLER MENU
This function is used to determine the filler menu optionsto be left active or to be disabled (ON/OFF):
- Statistics
- Single selection prices
- Change tubes control
- Special selections
- Test
- GSM connection
- EVADTS
The reference numbers of the menus do not change evenif some are disabled.
22© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
STATISTICS
Data on the machine operations is stored in both generalcounters and relative counters, which can be reset withoutlosing total data.
Connect an RS232 serial printer having a Baud rate of9600, 8 data bit, no parity, 1 stop bit to the serial portlocated on the push button board to print all of thestatistics, and namely:
Total1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;
Relative
1 - counter by single selection;2 - counter by time bands;3 - failure counter;4 - coin mechanism data;5 - photocell errors;6 - motor errors;The hardcopy printout will also contain the machine infor-mation, and namely:- date/time of print- machine name- software version- operator code- machine code- Installation date.To connect the printer, do as follows:
- press the confirm print button “ ”, displaying themessage “Confirm?”;
- connect the printer before confirming;
- press the confirm button “ ” to start printing.
DISPLAY
When pressing the confirm button “ ” the data describedin the paragraph “Printing the statistics” is sequentiallydisplayed.
RESETTING THE STATISTICSStatistics can be reset for counters globally (all types ofdata) or selectively for:
Total
- selections- failures- coin mechanism data- photocell errors;- motor errors;
Relative- selections- failures- coin mechanism data- photocell errors;- motor errors;Press the confirm button “ ”, and the message “Con-firm?” starts blinking.Press the confirm button “ ”, the message “Working” isdisplayed for a few seconds and all statistics are reset.N.B.: when resetting the total statistics also the relativestatistics are reset.
BDV protocol Audit
The information regarding the coin mechanism indicatesthe actual currency of:
Audit 1 Money in the tubesMoney present in the change tube that moment
Audit 2 Money to the tubesMoney sent to the change tubes
Audit 3 Money to the boxMoney sent to the coin box
Audit 4 Return of changeTotal money returned
Audit 5 Dispensed moneyTotal money dispensed manually
Audit 6 ExcessExcess money. Extra amounts paid by the customer thatwere not returned (in the event there was no moneyavailable for return)
Audit 7 Total salesTotal value of sales
Audit 8 Exact changeValue of sales in the “no change” condition.
Audit 9 Mixed dispensingTotal value of dispensing paid differently; for example alsoother types of payment (C.P.C., token).
Audit 10 Manual fillingMoney inserted in the coin mechanism through the manualfilling function.
23© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
MDB protocol AuditAudit 1 Money in the tubesMoney present in the change tubes that moment
Audit 2 Money to the tubesMoney sent to the change tubes
Audit 3 Money to the boxMoney sent to the coin box
Audit 4 Change returnTotal money returned
Audit 5 ExcessExcess money. Extra amounts paid by the customer thatwere not returned (in the event there was no moneyavailable for return)
Audit 6 Release of tubesValue of coins dispensed with the “Tubes control” function
Audit 7 Filling tubesValue of money cashed with the manual loading function
Audit 8 Cash salesValue of total sales with cash money (coins + bills)
Audit 9 Cashed billsValue of cashed bills
Aud. 10 Charge keyValue of money changed into the key
Aud. 11 Sales with keyValue of money cashed for dispensing with key
Audit. 12 Money dispensed manuallyValue of coins dispensed manually with the dispensingbuttons on the coin mechanism.
TEST
SELECTIONSThis function is used to simulate the normal dispensing ofproducts without inserting any money.Check the functioning of the motor rotation by pressing theselection buttons.
MOTOR TEST
It activates all motors in a sequence.
AUTOTESTA function to check, in a semiautomatic manner, thecorrect operation of some devices is implemented in thesoftware.Some checks occur automatically, others need the manualoperation of the monitored component; button “ ” ispressed to go to the next check.The monitored devices are:
“Keypad”
Press the button requested on the display; if it workscorrectly the request for the next button is presented.
“Temperature”The value of temperature detected by the probe is dis-played.In the event of disconnection the value -11.0 is displayed. In the event of a short-circuit the value 41.0 is displayed.“ ” to advance.
“Buzzer”
A series of sounds is emitted.
“Compressor”The compressor is activated/deactivated using the “ ”and “ ” buttons.
“Selections”
All selections are activated in a sequence.
“Coin mechanisms”Checking that communication with the coin mechanismtakes place correctly and which validator lines are set asbeing active.
“Photocells”
If the product detection device is present, the light beamreading and interruption are checked.
“Disp compt lock”If the device for locking the dispensing compartmentopening, use the “ ” and “ ” buttons to lock and unlock thecompartment opening.
“Direct keypad”
If fitted on the machine, the 5 buttons are checkedsequentially.Press the button requested on the display; if it workscorrectly the request for the next button is presented.
24© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
MACHINE INFORMATION
The machine can memorize a series of codes which willidentify it when retrieving statistics.More specifically the following can be stored:
- 6-digit operator code;
- 8-digit vending machine code which identifies themachine.
INSTALLATION DATE
This function is used to store the current date of system,if set correctly, as installation date.The date is printed when retrieving the statistics.
MACHINE CODEWhen the “Machine code” function is displayed the eight-digit numeric code identifying the machine can be changed(from the default 0).
OPERATOR CODE
When the “Operator code” function is displayed the six-digit numeric code identifying groups of machines can bechanged (from the default 0).
INITIALISING
When the “Initialise” function is displayed the vendingmachine can be initialised, selecting the “country” (in-tended as configuration type) and the language, restoringall related default data.This function should be used in the event of a memory dataerror or when the software version is replaced/updated.All statistic information will be reset.Press confirm button “ ”; the country and the language tobe used are requested, then the message “Confirm?” isdisplayed. Press confirm button “ ” a second time and themessage “Working” is displayed for a few seconds.
EVADTS CODES
The EVADTS (European Vending Association Data Trans-fer System) communication protocol has two codes foridentifying the machine and for recognising the datatransfer terminal:
PASS CODE
It is a four-digit alphanumeric code (0-9; A-F) that must bethe same as the one in the data transfer terminal to allowits identification.Press the confirm button “ ” and the code is displayed as“0000” regardless of the actual value; then press thechange button “ ” and the first digit will start blinking.Using the scrolling buttons, its value can be changed(during the change operation the value becomes visible).Press the confirm button “ ” and the next digit startsblinking.Press the confirm key “ ” after changing the fourth digit;the value is stored and the display indicates “0000” again.
SECURITY CODEIt is a further alphanumeric code for reciprocal recognitionbetween machine and EVADTS terminal.Programming works as in the “Pass” code.ConnectionThis function places the machine in wait mode for connec-tion to retrieve data.
EVADTS CONNECTION
When activating this function, the machine awaits theconnection with a device to acquire the EVADTS statis-tics.
GSM
The control software can send, via GSM modem, a signalindicating a machine failure or an “ending product” “pre-alarm”, after dispensing a programmable number of se-lections.The machine is pre-set to handle 7 pre-alarms.The first five can be associated to spirals and the last 2 totrays.
PIN CODEThis function is used for programming the identificationcode that will be sent to the GSM modem (optional) whenswitching the machine on.
SETTING THE THRESHOLDS
This function is used for defining the number of piecesafter which a “ending product” pre-alarm is signalled viamodem.
RESETTING THE COUNTERSWith this function the counters that control the pre-alarmsare reset.
THRESHOLD ASSOCIATION
This function is used for defining which spirals or trays toassociate to “pre-alarms” for “ending product”.By associating spiral 10 to pre-alarm N. 1 and setting thethreshold to 10 units with the “threshold setting” function,dispensing the tenth product from spiral 10 will generatea pre-alarm N. 1.By associating tray N. 5 to pre-alarm N. 6 and setting thethreshold to 30 units with the “threshold setting” function,dispensing the thirtieth product from tray 5 will generate apre-alarm N. 6.
MACHINE BANK NUMBERThe number in the bank of machines (1 to 7) that identifiesthemachines that have the “slave GSM” function, thereforesending data of the “master” machine via modem.The number 0 identifies the machine that is connecteddirectly to the modem, i.e. the “master GSM”.
25© by NECTA VENDING SOLUTIONS SpA 0407 239 -00
Chapter 3MAINTENANCE
The maintenance operations described in this chaptershould be carried out with the machine energised andtherefore by qualified personnel, who are trained in thecorrect use of the machine and are aware of the specificrisks of such condition.To energize the system with the open door, simply insertthe special key into the switch on the payment systemcompartment door (see Fig. 24).
Inside the machine, the only parts that stay energisedare those protected by covers and carrying a plate withthe warning “Disconnect the power before removingthe protective cover”.
Before removing such covers disconnect the machinefrom the power grid.
The integrity of the machine and compliance with thestandards of the relevant systems must be checked atleast once a year by qualified personnel.
PRINTED BOARD FUNCTIONSAND INDICATOR LAMPS
The C.P.U. (Central Processing Unit) board controls allusers set for the maximum configuration of the spiralcompartment and processes the input signals from thekeypad, the payment system and the cooling unit sensors.The card also houses some LEDs which, during themachine operation, give the following indications:
- Green LED (3): blinks during normal operation of theC.P.U. board;
- Yellow LED (4): glows when 5 V DC are detected;
- Red LED (7): glows when, for any reason, the softwareis reset.
CONFIGURING THE BOARD
This board is preset also for the MDB protocol.The 4 dip-switches for setting the SW2 coin mechanism(see Fig. 17) should be set to OFF for Executive-BDV andto ON for MDB.
SOFTWARE UPDATE
The machine is fitted with a Flash EPROM which can beelectronically updated.By means of a special program and suitable system(UpKey, Personal Computer or similar) the machine man-agement software can be updated without replacing theEPROM.Warning!When downloading the software it is advisable to discon-nect the motor connectors from the CPU board (J1 e J2).
Fig. 17
1 - J14 Coin mechanism power supply2 - J15 Board power supply3 - Green LED: run (DL2)4 - Yellow LED: 5 V DC (DL1)5 - J1 Dispensing compartment connection6 - J2 Spiral motor control7 - Red LED: CPU reset (DL3)8 - J3 Input/output9 - J17 UpKey connection10 - J4 Not used11 - J5 RS23212 - J6 Photocells13 - J7 Can-Bus14 - Button not used15 - J8 Validators16 - J9 Probe17 - J10 LCD display18 - J11 Direct selection keypad19 - J16 Keypad20 - J12 MDB expansion21 - Coin mechanism setting minidips (SW2)22 - J13 Expansion for BDV / EXE
26© by NECTA VENDING SOLUTIONS SpA 0407 239 -00
CONFIGURING THE TRAYS
PRODUCT SPACERS
The spacers are used when loading “narrow” products.The spacers should be fitted to contain products, withoutblocking them, towards the right-hand side of the com-partment, so that they stay upright. According to the typeof products, assess whether it is more convenient to usethe short or long side of the brackets and in which of thefive adjustment notches to connect them.Pull the spacer towards the front to close the space andpush it back to open the space.There must be at least 3 mm between the spacer and theproducts.
Fig. 18
PRODUCT EJECTOR
The ejectors, right-hand and left-hand, must be used forproducts packed in bags, such as potato crisps or similar.As they are hooked at the end of the spiral they push theproducts further out. If necessary slide the ejector alongthe spiral wire to locate the most appropriate positionaccording to the product being dispensed.
REPLACING THE SPIRALS
In order to change the number and the set-up of theproduct holders, proceed as follows:
- Slide out the concerned tray.
- Rotate the spiral in the opposite direction to the ejec-tion rotation, holding the plastic support flange still, toseparate the two parts and fit the other spiral.
- Fit the new spiral assembly proceeding in the oppositedirection, ensuring that the spiral is positioned correctly
Fig. 21
REMOVING THE TRAYS
To replace the trays proceed as follows:
- Slide out the tray to be modified;
- remove the electrical connector from the tray;
- lift the tray to unblock the retaining slide.
- To fit a new tray, proceed in the opposite way.
1 - Product spacer2 - Brackets3 - Adjustment notches
Fig. 19
1 - Spirals2 - Ejectors
Fig. 20
1 - Spiral2 - Plastic flange
27© by NECTA VENDING SOLUTIONS SpA 0407 239 -00
CHANGING THE NUMBER OF TRAYS
The vending machines are supplied with 7 trays.It is however possible to bring the number of trays to 5 or6, proceeding as follows:
- Disconnect the plug from the power supply.
- Remove all trays from the machine.
- Move the guides (see Fig. 22) placed on the sidesupports, except the first ones at the bottom which stayin the same position.
- Remove the pair of guides not used.
- Replace the 5 or 6 trays, ensuring that the connectorsare inserted properly.
- Secure the removed cables, as not to be in the way ofother trays and cables.
- Reprogram the machine.
CHANGING THE TRAY CONFIGURATION
The configuration of the spirals on each tray can bechanged. To go from two selections with single spirals toone selection with double spirals, do as follows:
- Remove the tray to be modified.
- Remove the centre wall, pushing it towards the backand then lifting.
- Remove the spirals, and the flanges, from the twomotors.
- Disconnect the left-hand side motor from the cable andremove it from the tray. In its place, fit the bush and pinbush.
- Install the right-hand and left-hand spirals with thesame pitch onto the new flanges (right and left areidentical), fitted with a cogged wheel, and then connectthe right-hand one to the motor still on the tray and theleft-hand one onto the previously installed bushes. Thetwo cogged wheels must mesh.
- Remove the price labels and the product holders nolonger used, and if necessary update the price labelsstill in use.
- Program the new selections with the desired price.
- Test the modified selections, to be sure of their correctoperation.
Fig. 23
N.B.: The selection numbers are formed by two figures;the first figure refers to the tray number, counting from thetop (1-6), the second figure refers to the spiral number,counting from the left (0-5).The selection number to which the motor is connected willtherefore be formed by the tray number plus the wire codenumber.
Fig. 22
1 - Tray connector2 - Tray guide
1 - Tray2 - Mobile walls3 - Right-hand spiral4 - Left-hand spiral
28© by NECTA VENDING SOLUTIONS SpA 0407 239 -00
POWER SUPPLY UNIT
Fuses, switch and connectors positioned at the front of thepower supply unit have the functions indicated below.
When replacing any fuses the power supply cablemust be disconnected from the mains.
ACCESS TO THE COOLING UNIT
If for any reason the cooling unit need to be accessed fromthe machine, do as follows:
- remove the last tray
- remove the anti-theft grille
- undo the fastening screws from the product dispensingcompartment and remove it
- For reassembly, proceed in the reverse order.
Fig. 24
1 Line fuses2 Transformer primary winding protection fuse3 CPU board power supply connector4 Lamp connector5 Compressor and fan connector6 Transformer secondary winding protection fuse7 Transformer secondary winding protection fuse8 Payment system compartment switch
Fig. 25
1 Anti-intrusion grille2 Dispensing compartment3 Photocell support
Fig. 26
1 Evaporator2 Fan3 Condenser4 Dispensing compartment
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
29
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
With
the
prin
ter
conn
ecte
dpr
int
all d
ata
as d
ispl
ayed
TO
TA
L S
TA
TIS
TIC
S
Prin
t da
ta f
or:
Sel
ectio
nsT
ime
band
sF
ailu
res
Coi
n m
echa
nism
dat
aP
hoto
cell
erro
rsM
otor
err
ors
Prin
ting.
..
Hea
din
g:
Cur
rent
dat
eM
achi
ne m
odel
Sof
twar
e ed
ition
Ope
rato
r co
deM
achi
ne c
ode
Inst
alla
tion
date
RE
LA
TIV
E S
TA
TIS
TIC
S
FILL
>1
Stat
istic
sFI
LL >
1.1
Prin
t sta
tistic
sFI
LL >
1.1.
1Pa
rtial
prin
tout
FILL
>1.
1.1.
1Se
lect
ions
Con
firm
?
Prin
t Sel
ectio
ns
Prin
ting.
..
Prin
t Sel
ectio
ns
FILL
>1.
1.2
Tota
l prin
tout
Con
firm
?
Tota
l prin
tout
Prin
ting.
..
Tota
l prin
tout
FILL
>1.
2Pr
int r
elat
ive
stat
sFI
LL >
1.2.
1Pa
rtial
prin
tout
FILL
>1.
2.1.
1Se
lect
ions
Con
firm
?
Prin
t Sel
ectio
ns
Prin
ting.
..
Prin
t Sel
ectio
ns
FILL
>1.
2.2
Tota
l prin
tout
Con
firm
?
Tota
l prin
tout
Prin
ting.
..
Tota
l prin
tout
FILL
>1.
3D
ispl
ay s
tatis
tics
FILL
>1.
3.1
Dis
play
sel
. cou
nter
FILL
>1.
3.1.
1D
isp.
sin
gle
coun
ter
Dis
play
sal
es b
y si
ngle
sele
ctio
n fo
r ea
ch t
ime
band
and
tota
l
Dis
play
tot
al s
ales
by
sing
lese
lect
ion
TO
TA
L S
TA
TIS
TIC
S
Sele
ctio
n ##
Tim
e ba
nd #
= #
###
FILL
>1.
3.1.
2D
isp.
tota
l cou
nter
Sele
ctio
n ##
Tota
l = #
##
Dis
play
tot
al s
ales
in n
orm
alop
erat
ion
and
test
mod
eFI
LL >
1.3.
2C
ount
. by
time
band
sTi
me
band
0÷4
Cou
nter
=
##
#
FILL
>1.
3.3
Dis
play
failu
res
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
30
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
Mo
nit
ore
d f
ailu
res:
Com
pres
sor
Coi
n m
echa
nism
RA
M d
ata
Pro
beD
ispe
nsin
g co
mpa
rtm
ent
lock
(Foo
d on
ly)
Saf
ety
tem
pera
ture
Com
pres
sor
Cou
nter
=
##
#
FILL
>1.
3.2
Cou
nt. b
y tim
e ba
nds
FILL
>1.
3.3
Dis
play
failu
res
CO
IN M
EC
HA
NIS
M D
AT
A(a
ccor
ding
to
prot
ocol
use
d)
Val
idat
ors
and
Exe
cutiv
eC
ashe
d an
d so
ld
BD
V A
udit
MD
B A
udit
FILL
>1.
3.4.
1Au
dit d
ata
FILL
>1.
3.4
Disp
. coin
mec
h da
ta
FILL
>1.
3.4.
2Di
splay
cas
h co
unte
r
Err.
befo
re d
isp.
Cou
nter
= #
##FI
LL >
1.3.
5D
isp.
pho
t. er
r. cn
t.
Ph
oto
cell
erro
rs:
Bef
ore
disp
ensi
ngA
fter
disp
ensi
ngP
rodu
ct n
ot d
etec
ted
Sele
ct. N
. ##
Cou
nter
= #
##FI
LL >
1.3.
6D
isp.
mot
. err.
cnt
.
Mo
tor
erro
r
FILL
>1.
4D
ispl
ay re
lativ
e st
ats
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
31
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
Fill
er m
enu
- S
um
mar
y
Dis
play
sal
es b
y si
ngle
sele
ctio
n fo
r ea
ch t
ime
band
and
tota
l
Dis
play
tot
al s
ales
by
sing
lese
lect
ion
RE
LA
TIV
E S
TA
TIS
TIC
S
Dis
play
tot
al s
ales
in n
orm
alop
erat
ion
and
test
mod
e
FILL
>1.
4.1
Dis
play
sel
. cou
nter
FILL
>1.
4.1.
1D
isp.
sin
gle
coun
ter
Sele
ctio
n ##
Tim
e ba
nd #
= #
###
FILL
>1.
4.1.
2D
isp.
tota
l cou
nter
Sele
ctio
n ##
Tota
l = #
##
FILL
>1.
4D
ispl
ay re
lativ
e st
ats
FILL
>1.
4.2
Cou
nt. b
y tim
e ba
nds
Tim
e ba
nd 0
÷4C
ount
er =
###
Com
pres
sor
Cou
nter
=
##
#FI
LL >
1.4.
3D
ispl
ay fa
ilure
s
FILL
>1.
4.4.
1Di
sp. c
oin m
ech
coun
terFI
LL >
1.4.
4Di
sp. c
oin m
ech
data
FILL
>1.
4.4.
2Di
splay
cas
h co
unte
r
Mo
nit
ore
d f
ailu
res:
Com
pres
sor
Coi
n m
echa
nism
RA
M d
ata
Pro
be
CO
IN M
EC
HA
NIS
M D
AT
A(a
ccor
ding
to
prot
ocol
use
d)
Val
idat
ors
and
Exe
cutiv
eC
ashe
d an
d so
ld
BD
V A
udit
MD
B A
udit
FILL
>1.
5D
elet
e re
lativ
e st
ats
Err.
befo
re d
isp.
Cou
nter
= #
##FI
LL >
1.4.
5D
isp.
pho
t. er
r. cn
t.
Ph
oto
cell
erro
rs:
Bef
ore
disp
ensi
ngA
fter
disp
ensi
ngP
rodu
ct n
ot d
etec
ted
Sele
ct. N
. ##
Cou
nter
= #
##FI
LL >
1.4.
6D
isp.
mot
. err.
cnt
.
Mo
tor
erro
r
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
32
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
Fill
er m
enu
- S
um
mar
y
Del
ete
data
for
:S
elec
tions
Tim
e ba
nds
Fai
lure
sC
oin
mec
hani
sm d
ata
Pho
toce
ll er
rors
Mot
or e
rror
s
RE
LA
TIV
E S
TA
TIS
TIC
SFI
LL >
1.5.
1D
elet
e pa
rtial
FILL
>1.
5.1.
1D
elet
e se
lect
ions
Con
firm
?
Del
ete
sele
ctio
ns
Wor
king
...
Del
ete
sele
ctio
ns
FILL
>1.
5.2
Del
ete
tota
lC
onfir
m?
Del
ete
sele
ctio
ns
Wor
king
...
Del
ete
sele
ctio
ns
FILL
>1.
5D
elet
e re
lativ
e st
ats
FILL
>2
Sing
le p
rices
Opt
ion
of c
hang
ing
sale
spr
ice
for
each
sel
ectio
n in
4tim
e ba
nds
FILL
>2.
1Pr
ice
band
#Se
lect
ion
Pric
e
##
##
BD
V o
nly
Man
ual c
hang
e tu
be r
efill
Man
ual t
ube
rele
asin
gR
elea
se tu
bes
Tube
A ÷
X
FILL
>3Tu
be c
ontro
lFi
ll tu
bes
Cre
dit:#
####
FILL
>3.1
Fill
tube
s
FILL
>4Sp
ecia
l sel
ectio
ns
FILL
>3.2
Rel
ease
tube
sR
elea
se tu
bes
Wor
king
...
Ent
er n
umer
icva
lue
10
####
#
Sele
ctio
n 1
0Pr
ice
Ent
er n
umer
icva
lue
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
33
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
Fill
er m
enu
- S
um
mar
y
FILL
>4Sp
ecia
l sel
ectio
nsFI
LL>4
.1Vi
rtual
sel
ectio
ns
FILL
>4.2
Virtu
al p
rice
chan
geO
N/O
FF
Virtu
al p
rice
chan
ge
FILL
>4.
3Tw
o-m
otor
sel
ectio
n
FILL
>4.
4Ph
otoc
ell p
aram
eter
sFI
LL >
4.4.
1Se
ttlin
g tim
e
FILL
>4.
4.2
Mon
ey re
turn
FILL
>4.
4.3
Empt
y se
l. co
ntro
l
Sele
ct. n
r.Ti
me
(s/1
00)
=
VIR
TU
AL S
EL
EC
TIO
NS
Set
ting
two
sele
ctio
ns (
10 t
o79
) in
a v
irtua
l one
(80
to 8
4)
##
ON
/OFF
Mon
ey re
turn
ON
/OFF
Empt
y se
l. co
ntro
l
FILL
>5Te
st
##
Sele
ctio
n
nn
+
00nn
Sel
ectio
ns 1
0 to
79
mm
num
ber
of c
ombi
ned
mot
orif
mm
= n
n th
e co
mbi
natio
nbe
twee
n th
e tw
o se
lect
ions
isca
ncel
led
Sele
ctio
n
nn
nn
+
mm
Sele
ctio
n nr
.##
Sele
ct. #
# +
####
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
34
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
Fill
er m
enu
- S
um
mar
y
FILL
>5
Test
FILL
>5.
1Te
st s
elec
tion
FILL
>5.
2M
otor
test
FILL
>5.
3Au
tote
st
Wai
t ple
ase
Sele
ctio
n nr
.##
Con
firm
?
Keyp
ad te
st
Sele
ctio
n nr
.##
Wai
t ple
ase
The
sel
ectio
n nu
mbe
rch
ange
s au
tom
atic
ally
Keyp
ad te
stPr
ess
1 bu
tton
#
Whe
n pr
essi
ng t
he b
utto
n,th
e ne
xt b
utto
n is
pre
sent
edau
tom
atic
ally
Con
firm
?
Tem
pera
ture
test
Tem
pera
ture
test
Tem
p. =
12.
2 °C
Con
firm
?
Buzz
er te
stBu
zzer
test
Wor
king
...
Em
issi
on o
f a
serie
s of
soun
ds
Con
firm
?
Com
pres
sor t
est
Com
pres
sor t
est
ON
/OFF
OF
F
ON
Con
firm
?
Sele
ctio
n te
st
Wai
t ple
ase
Sele
ctio
n nr
.##
All
sele
ctio
ns a
re a
ctiv
ated
ina
sequ
ence
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
35
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
Con
firm
?
Coi
n m
ech
test
Failu
re li
st
Coi
n m
ech
test
WIT
H E
XE
CU
TIV
E, B
DV
OR
MD
B C
OIN
ME
CH
AN
ISM
S
If th
e co
in m
echa
nism
com
mun
icat
es it
dis
play
s "O
K"
AL
TE
RN
AT
IVE
LY
WIT
H A
VA
LID
AT
OR
Con
firm
?
Coi
n m
ech
test
Coi
n m
ech
test
Coi
n m
ech
test
Valid
. lin
e #
Line
tw
o re
mai
ns f
orap
prox
imat
ely
2 se
cond
s
Con
firm
?
Phot
ocel
l tes
tW
ITH P
HO
TO
CE
LL
S
DIS
CO
NN
EC
TE
D
AL
TE
RN
AT
IVE
LY
Phot
ocel
l tes
tAb
sent
Con
firm
?
Phot
ocel
l tes
t
Failu
re li
st
Phot
ocel
l tes
tIf
the
light
bea
m is
inte
rrup
ted
with
in2.
5 se
cond
s it
disp
lays
"O
K"
or Err
or n
o pr
oduc
tIf
a fa
ilure
is p
rese
nt:
Err
or a
fter
disp
ensi
ngE
rror
bef
ore
disp
ensi
ng
WIT
H P
HO
TO
CE
LL
S
© by NECTA VENDING SOLUTIONS SpA 0407 239 - 00
36
Fill
er m
enu
- S
um
mar
y
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-
1)
NE
XT
FU
NC
TIO
N/
INC
RE
AS
E D
AT
A U
NIT
(+
1)
DIR
EC
T A
CC
ES
S T
O C
HA
NG
EP
RIC
E O
F T
IME
BA
ND
0
Con
firm
?
Dis
p. c
omp'
t loc
k
ON
/OFF
Dis
p. c
omp'
t loc
kW
ith d
ispe
nsin
g co
mpa
rtm
ent
lock
pre
sent
Con
firm
?
Dire
ct k
eypa
d te
stD
irect
key
pad
test
Pres
s 1
butto
n#
Whe
n pr
essi
ng t
he b
utto
n,th
e ne
xt b
utto
n is
pre
sent
edau
tom
atic
ally
Con
nect
ion
FILL
>7.1
FILL
>7EV
ADTS
Wai
t ple
ase
FILL
>7.1
FILL
>1St
atis
tics
Sele
ctio
n 1
0Pr
ice
=
Sele
ctio
nPr
ice
=
###
#
Ent
er n
umer
ic v
alue
10
####
FILL
>6G
SMR
eset
pre
-ala
rmco
unte
rsC
onfir
m?
Del
ete
tota
l
Wor
king
...
Del
ete
tota
l
Res
ettin
g pr
e-al
arm
cou
nter
s
Aw
aitin
g th
e co
nnec
tion
with
EV
AD
TS
dev
ice
© by NECTA VENDING SOLUTIONS SpA
37
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
Tim
e sc
rolli
ng o
f pr
esen
tfa
ilure
s
Pos
sibl
e m
otor
con
ditio
ns:
- O
K-
Blo
cked
- D
isco
nnec
ted
- N
ot f
unct
ioni
ng-
Not
pre
sent
- E
mpt
y se
lect
ion
TEC
H >
1F
ailu
res
TEC
H >
1.1
Rea
d fa
ilure
s
TEC
H >
1.2
Res
et f
ailu
res
TEC
H >
2P
rogr
. pa
ram
eter
s
Mo
nit
ore
d f
ailu
res:
Co
mp
ress
or
Coi
n m
echa
nism
RA
M d
ata
Pro
beD
ispe
nsin
g co
mpa
rtm
ent
lock
(Foo
d on
ly)
Saf
ety
tem
pera
ture
Res
et f
ailu
res
Don
e!
TEC
H >
1.4
Mot
or s
tatu
sM
otor
nr.
##
TEC
H >
1.8
Res
et m
ot.
err.
Res
et m
ot.
err.
Failu
re n
ame
Con
firm
?
DIS
PLA
YIN
G FA
ILU
RE
S
TEC
H >
1.3
Mot
or e
rror
s
TEC
H >
1.1
End
of
failu
res
Tim
e sc
rolli
ng o
f pr
esen
tfa
ilure
sFa
ilure
nam
e
Mot
or e
rror
s
© by NECTA VENDING SOLUTIONS SpA
38
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
2.1
Cas
hTE
CH
>2
Pro
gr.
para
met
ers
TEC
H >
2.1.
1.1
Sin
gle
pric
esTE
CH
>2.
1.1
Pric
esTE
CH
>2.
1.1.
1.1
Pric
e ba
nd #
TEC
H >
2.1.
1.2
Glo
bal p
rices
TEC
H >
2.1.
1.2.
1P
rice
band
#4
time
band
s pl
us b
and
0(n
o tim
e ba
nd s
et)
avai
labl
ew
ith d
iffer
ent
pric
es f
or e
ach
sele
ctio
n
TEC
H >
2.1.
1.3
Tim
e ba
nds
Opt
ion
of c
hang
ing
sale
spr
ice
for
each
sel
ectio
n in
4tim
e ba
nds
Sel
ectio
nPr
ice
#
###
Ent
er n
umer
icva
lue
10
####
Sel
ectio
n
10P
rice
####
Pric
e ba
nd #
Pric
e
© by NECTA VENDING SOLUTIONS SpA
39
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
2.1.
1.3
Tim
e ba
nds
X +
1
X -
1
TEC
H >
2.1.
1.3.
1S
et d
ate
and
time
Dat
e: d
d/m
m/y
y d#
Yea
r##
X +
1
X -
1
Tim
e: h
h/m
m/s
sTi
me:
##
X +
1
X -
1
TEC
H >
2.1.
1.3.
2Ti
me
band
1-4
Sta
rt: h
h/m
mE
nd:
hh/
##
CLO
CK
Whe
n co
nfirm
ing
the
blin
king
valu
es,
day,
mon
th,
year
and
wee
k da
y ar
e en
tere
d on
e af
ter
the
othe
r. W
hen
conf
irmin
g th
ew
eek
day
hour
and
min
utes
are
disp
laye
d, t
hat
can
then
be
chan
ged
and
conf
irmed
.
TIM
E B
AN
DS
Whe
n co
nfirm
ing
the
blin
king
valu
es,
hour
and
min
ute
for
star
t an
d en
d of
tim
e ba
nd a
reen
tere
d on
e af
ter
the
othe
r.W
hen
star
t an
d en
d of
tim
eba
nd a
re s
et t
o 00
.00
the
band
sar
e no
t ac
tivat
ed.
© by NECTA VENDING SOLUTIONS SpA
40
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
AV
AIL
AB
LE C
OIN
ME
CH
AN
ISM
S
Val
idat
ors
Exe
cutiv
eB
DV
MD
B
TY
PE O
F V
EN
DIN
G
CH
AN
GE W
ITH
OU
T VE
ND
TEC
H >
2.1.
2.1
Set
coi
n m
ech
TEC
H >
2.1.
2C
oin
mec
hani
sms
Coi
n m
ech
type
Coin
mec
h nam
e
Type
of
Ven
ding
Type
of
Ven
ding
Max
imum
cre
dit
Val
ue =
###
##V
alue
=
Max
imum
cha
nge
Val
ue =
###
##V
alue
=
####
####
Sin
gle/
Mul
ti
Cha
nge
butto
nON
Cha
nge
butto
n O
N
Exe
cutiv
e
Pro
toco
lE
XE
CU
TIV
E PR
OTO
CO
LS
Sta
ndar
dP
rice
Hol
ding
Co
ge
sU
Ke
yS
ida
ALT
ER
NA
TIV
ELY
BD
V/M
DB
Val
idat
ors
Exe
cutiv
e
A to
F
Val
idat
orLi
neLi
neV
alue
####S
ET
TIN
G TH
E V
AL
UE O
F
VA
LID
ATO
R LI
NE
S
ON
XX
XX
+ 1
XX
XX
- 1
ON
OF
F
XX
XX
+ 1
XX
XX
- 1
XX
XX
+ 1
XX
XX
- 1
© by NECTA VENDING SOLUTIONS SpA
41
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
Coi
ns 1
to
16
Yes
Coi
n #
Acc
epte
d co
ins
Coi
ns 1
Coi
ns 1
to
16
Yes
Coi
n #
Acc
epte
d ch
ange
Coi
ns 1
Dis
p. b
utto
nsON
But
ton
0 =
A o
r (B
and
C)
1 =
A a
nd B
and
C2
= A
and
B o
nly
3 =
A a
nd (
B o
r C
)4
= A
onl
y5
= A
or B
onl
y (d
efau
lt)6
= A
or
B o
r C
7 =
A o
r B
onl
y8
= A
or
C o
nly
9 =
B a
nd C
onl
y10
= B
onl
y11
= B
or
C o
nly
12 =
C o
nly
Com
bina
tion
1-12
Eq.
exa
ct c
hang
eC
ombi
natio
n#
C.P
.C.
devi
ceON
C.P
.C.
unit
Ena
ble
Dis
able
ON
OF
F
Ena
ble
Dis
able
ON
OF
F
Ena
ble
Dis
able
Yes
No
Ena
ble
Dis
able
Yes
No
© by NECTA VENDING SOLUTIONS SpA
42
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
Exa
ct c
hang
e
Free
ven
d V
MC
But
ton
Val
ue =
####
Val
ue =
###
##
TEC
H >
2.1.
2.2
Imm
edia
te c
hang
eON
Imm
edia
te c
hang
e
TEC
H >
2.1.
3D
ecim
al p
oint
2#
Poi
nt p
osit.
= #
New
pos
it. =
X +
1
X -
1
Imm
edia
te c
hang
e at
disp
ensi
ng s
tart
Cho
ices
are
:
No
Mas
ter
Ma
ste
r A
stro
Mas
ter
Sfe
raM
aste
r S
fera
2M
ast
er
Sn
akk
y M
ax
Ma
ste
r S
na
kky
Ma
x 2
No
Sla
veS
lave
Ast
roS
lave
Sfe
raS
lave
Sfe
ra 2
Sla
ve S
na
kky
Ma
xS
lave
Sn
akk
y M
ax
2
If an
Exe
cutiv
e P
rice
Hol
ding
syst
em i
s se
t on
the
mas
ter,
it m
ust
be s
et a
lso
on t
hesl
ave
ON
OF
F
TE
CH
>2.1
.4.2
Sla
ve P
r. H
old. O
FF
TE
CH
>2.1
.4.1
No
Mas
ter
TE
CH
>2.1
.4M
aste
r/Sla
ve
TE
CH
>2.1
.4.2
Sla
ve P
r. H
old.
OF
F
Sla
ve 1 No
Sla
ve
Sla
ve 2 N
o S
lave
Dec
imal
poi
nt 0
to
3
XX
XX
+ 1
XX
XX
- 1
Ena
ble
Dis
able
ON
OF
F
Ena
ble
Dis
able
ON
OF
F
ON
© by NECTA VENDING SOLUTIONS SpA
43
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H>2
.1.4
.3C
ombi
ned
sele
ctio
ns
Com
bine
d se
lect
ions
85 t
o 89
1st
com
bine
d se
lect
ion
Sn
akk
y10
to
79
2nd
com
bine
d se
lect
ion
Ast
ro01
to
18o
rS
lave
101
0 to
079
Sla
ve 2
910
to 9
76
##Se
lect
. nr
. 80
Sel.
+
##
Sele
ct.
nr.
Sel.
##
+ ##
##
Sele
ct.
nr.
80Se
l.
##
+ #
#
TEC
H>2
.1.4
.4R
eset
Sna
kky
SLTE
CH
>2.1
.4.4
Res
et S
nakk
y SL
Whe
n sw
itchi
ng o
n on
e of
the
tw
opo
ssib
le s
lave
mac
hine
s, i
ts d
ata
is r
eset
.A
t th
e en
d em
issi
on o
f a
soun
dsi
gnal
.
TEC
H>2
.1.4
.5M
onito
rTE
CH
>2.1
.4.5
Mon
itor
Whe
n sw
itchi
ng o
n on
e of
the
tw
opo
ssib
le s
lave
mac
hine
s, t
hefo
llow
ing
is d
ispl
ayed
:-
softw
are
editi
on-
type
of
slav
e (X
X, 0
XX
, 9X
X)
- pr
esen
ce o
f ph
otoc
ells
- nu
mbe
r of
tra
ys a
nd c
ompa
rtm
ents
- pr
esen
ce o
f lo
ck d
evic
e-
inte
rnal
tem
pera
ture
TEC
H >
2.1.
5Fr
ee v
end
bonu
sTE
CH
>2.
1.5.
1En
able
bon
usO
NO
FF
ON
Bonu
s fre
quen
cyon
e ev
ery
###
S.
#
If O
N t
he a
vera
ge n
umbe
r of
sele
ctio
ns (
0001
to
9999
) be
twee
ntw
o bo
nuse
s is
req
uest
ed
TEC
H >
2.2
Sele
ct./s
pira
ls
© by NECTA VENDING SOLUTIONS SpA
44
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
2.2
Sele
ct./s
pira
lsTE
CH
>2.
2.1
Spira
l pa
ram
eter
sTE
CH
>2.
2.1.
1M
achi
ne c
onfig
.M
achi
ne c
onfig
.C
onfir
m?
TEC
H>
2.2.
1.2
Virtu
al s
elec
tions
Sele
ctio
n nr
.##
Sele
ct.
## +
TEC
H>
2.2.
1.3
Virtu
al p
rice
chan
geO
N/O
FF
Virtu
al p
rice
chan
ge
VIR
TUA
L SE
LEC
TIO
NS
Set
ting
two
sele
ctio
ns (
10 t
o79
) in
a v
irtua
l on
e (8
0 to
84)
##
TEC
H>
2.2.
1.4
Two-
mot
or s
elec
tion
Sele
ctio
n
nn
+
00
nnS
elec
tions
10
to 7
9
mm
num
ber
of c
ombi
ned
mot
orif
mm
= n
n th
e co
mbi
natio
nbe
twee
n th
e tw
o se
lect
ions
isca
ncel
led
Sele
ctio
n
n
n
nn
+
mm
© by NECTA VENDING SOLUTIONS SpA
45
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H>
2.2.
1.6
Prod
uct
code
#Se
lect
ion
n
nC
ode:
###
Sele
ctio
n
Cod
e:
#
###
nnS
elec
tions
10
to 7
9
TEC
H >
2.2.
1.7
Dire
ct s
elec
tions
TEC
H >
2.2.
1.7.
1En
able
dir.
sel
.
TEC
H >
2.2.
1.7.
2Se
t di
r. se
l.
ON
/OFF
Enab
le d
ir. s
el. #
Dir.
sel
. N
r. 1
Sel.
##+
##
Dir.
sel
. N
r.=
sel.
nr.
##
Dire
ct s
elec
tions
1 to
5
Min
imum
and
max
imum
num
ber
of s
elec
tions
corr
espo
ndin
g to
the
dire
ctse
lect
ion
(10
to 7
9)
TEC
H>
2.2.
1.5
Rot
atio
n se
lect
ion
##Se
lect
ion
from
##
to
Gro
up N
r.
ON
/OFF
:
##
##
nG
roup
s 1
to 7
Min
imum
and
max
imum
num
ber
of s
elec
tions
corr
espo
ndin
g to
the
gro
upof
rot
atio
n se
lect
ions
© by NECTA VENDING SOLUTIONS SpA
46
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H>2
.2.3
Com
pt.
lock
par
am.
TEC
H>
2.2.
3.1
Ope
ratin
g m
ode
TEC
H>
2.2
.3.2
Unl
ock
time
TEC
H>
2.2.
3.3
Tim
e ou
t of
ser
vice
Mod
e
Alw
ays
unlo
cked
Unl
ocke
d up
on d
ispe
nsin
gfo
r ##
min
utes
Unloc
k on d
isp. ##
01 t
o 10
min
utes
Unl
ock
time
Dur
atio
n:
Tim
e ou
t of
ser
vice
Dur
atio
n:
##
UN
LOC
K D
ISP
EN
SIN
G
CO
MP
AR
TME
NT
01 t
o 10
min
utes
TEC
H>
2.2.
3.4
Out
of
serv
ice
if op
enO
N/O
FF
Out
of
serv
ice
if op
enO
ut o
f se
rvic
e if
the
com
part
men
t fa
ils w
hen
open
TEC
H>2
.2.2
Phot
ocel
l pa
ram
eter
sTE
CH
> 2.
2.2.
1Se
ttlin
g tim
e
TEC
H>
2.2
.2.2
Mon
ey r
etur
n
TEC
H>
2.2.
2.3
Empt
y se
l. co
ntro
l
ON
/OFF
Mon
ey r
etur
n
ON
/OFF
Empt
y se
l. co
ntro
l
Sele
ct.
nr.
Tim
e (s
/100
) =
####
© by NECTA VENDING SOLUTIONS SpA
47
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
2.3.
1Te
mpe
ratu
re
TEC
H >
2.3.
3En
able
col
d un
it
TEC
H >
2.3
Col
d pa
ram
eter
s
Ope
ratin
g te
mpe
ratu
re5°
to
20°C
.8°
C b
y de
faul
t
Inte
rnal
tem
pera
ture
Tem
p. °
C =
##
TEC
H >
2.3.
2D
efro
stin
g
Def
rost
ing
inte
rval
0 to
99
hour
s6
hour
s by
def
ault
Def
rost
ing
inte
r.D
efr.
inte
r. =
##
ON
/OFF
Enab
le c
old
unit
Fo
od
mo
del
s2°
to
20°C
.8°
C b
y de
faul
t
TEC
H >
2.3.
4En
able
Foo
d co
ntro
lO
N/O
FF
Enab
le F
ood
cont
rol
Enab
le t
ray
##O
N/O
FF
TEC
H >
2.3.
5Te
mpe
ratu
re l
ogSa
mpl
e ##
###
.##.
##
##.#
# ##
Tra
ys 4
to
6
0 to
143
sam
ples
.R
eadi
ng o
fda
tetim
ete
mpe
ratu
re
© by NECTA VENDING SOLUTIONS SpA
48
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
2.4
Dis
play
TEC
H >
2.4.
1La
ngua
geLa
ngua
ge Lang
uage
Italia
nE
nglis
hF
ren
chS
pani
shP
ortu
gues
eF
lem
ish
AV
AIL
AB
LE LA
NG
UA
GE
S
TEC
H >
2.4.
2U
ser
disp
lay
No
mes
sage
sIn
tern
al t
empe
ratu
reT
ime
PO
SS
IBLE
ME
SS
AG
ES
TEC
H >
2.4.
3Pr
omo.
mes
sage
Use
r di
spla
y
Mes
sage
En.
prom
o. m
essa
ge
ON
/OFF
TEC
H >
2.4.
3.2
Prog
. pr
omo.
mes
sage
Le
tter
scro
lling
in
ase
quen
ce (
20 c
hara
cter
spe
r 4
lines
)
Nex
t le
tter
Nex
t m
essa
ge
CH
AN
GE 2
-LIN
E U
SE
R
ME
SS
AG
E
TEC
H >
2.4.
4Pe
rson
alis
ed s
tring
s
TEC
H >
2.4.
3.1
En.
prom
o. m
essa
ge
Cha
nge
line
1
Line
1
Cha
nge
line
2
Line
2
TEC
H >
2.3
Col
d pa
ram
eter
s
© by NECTA VENDING SOLUTIONS SpA
49
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
2.4.
4Pe
rson
alis
ed s
tring
sEn
able
per
s. s
tring
s
TEC
H >
2.4.
4.2
Prog
. pe
rs.
strin
gs
Le
tter
scro
lling
in
ase
quen
ce (
20 c
hara
cter
spe
r 4
lines
)
Nex
t le
tter
Nex
t st
ring
(1 t
o 30
)
CH
AN
GE ST
RIN
GS
TEC
H >
2.4.
5D
ispl
ay c
ount
er
TEC
H >
2.4.
4.1
Enab
le p
ers.
stri
ngs
Cha
nge
strin
g 1
Line
1
ON
/OFF
Dis
play
cou
nter
ON
/OFF
TEC
H >
2.4.
6C
ontra
st c
ontro
lC
ontra
st c
ontro
lK
= (5
- 99
)
Dis
play
ing
the
gene
ral
coun
ter
upon
sw
itchi
ng o
nth
e m
achi
ne
##
Ent
er t
he p
erce
ntag
e va
lue
from
the
key
pad
TEC
H >
2.5
Mis
cella
neou
s
© by NECTA VENDING SOLUTIONS SpA
50
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
2.5.
1Se
t pa
ssw
ord
ON
/OFF
Set
pass
wor
dTE
CH
>2.
5M
isce
llane
ous
Set
pass
wor
dPa
ssw
ord:
###
##
TEC
H >
2.5.
2En
ergy
Sav
ing
Ener
gy S
avin
gX
+ 1
X - 1
Ener
gy S
av.
Para
m.
Tim
e ba
nd 1
-4St
art:
hh/m
mEn
d: h
h/##
ON
/OFF
TEC
H >
2.5.
2.1
Ener
gy S
avin
g
Whe
n co
nfirm
ing
the
blin
king
valu
es,
hour
and
min
ute
for
star
t an
d en
d of
tim
e ba
nd a
reen
tere
d on
e af
ter
the
othe
r.W
hen
star
t an
d en
d of
tim
eba
nd a
re s
et t
o 00
.00
the
band
s ar
e no
t ac
tivat
ed.
5-di
git
num
ber
to a
cces
s th
ete
chni
cian
men
u
IF O
N
TEC
H >
3St
atis
tics
FILL
ER M
EN
U
TEC
H >
2.5.
3M
aski
ng f
iller
men
uM
enu
nam
e
ON
/OFF
Sta
tistic
sS
ingl
e pr
ices
BD
V t
ube
cont
rol
Spe
cial
sel
ectio
nsT
est
EV
AD
TS
con
nect
ion
TEC
H >
2.5.
4N
eon
out
of s
ervi
ceN
eon
out
of s
ervi
ce
ON
/OFF
If O
N,
exte
rnal
lig
htin
g is
switc
hed
off
with
ven
ding
mac
hine
out
of
serv
ice
© by NECTA VENDING SOLUTIONS SpA
51
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
3St
atis
tics
TEC
H >
3.1
Dis
play
sta
tistic
sTE
CH
>3.
1.1
Dis
play
sel
. co
unte
rTE
CH
>3.
1.1.
1D
isp.
sin
gle
coun
ter
Dis
play
sal
es b
y si
ngle
sele
ctio
n fo
r ea
ch t
ime
band
and
tot
al
Dis
play
tot
al s
ales
by
sing
le s
elec
tion
TOTA
L STA
TIS
TIC
SSe
lect
ion
##Ti
me
band
# =
###
#
TEC
H >
3.1
.1.2
Dis
p. to
tal c
ount
erSe
lect
ion
##To
tal =
###
Del
ete
data
for
:S
elec
tions
Tim
e ba
nds
Fai
lure
sC
oin
mec
hani
sm d
ata
Pho
toce
ll er
rors
Mot
or e
rror
s
DE
LETE
STA
TIS
TIC
STE
CH
>3.
2.1
Del
ete
parti
alTE
CH
>3.
2.1.
1D
elet
e se
lect
ions
Con
firm
?
Del
. se
l. co
unte
r
Wor
king
...
Del
. se
l. co
unte
r
TEC
H >
3.2.
2D
elet
e to
tal
Con
firm
?
Del
ete
sele
ctio
ns
Wor
king
...
Del
ete
sele
ctio
ns
TEC
H >
3.2
Del
ete
stat
istic
s
TEC
H >
3.3
Dis
play
rel
ativ
e st
ats
© by NECTA VENDING SOLUTIONS SpA
52
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
Dis
play
sal
es b
y si
ngle
sele
ctio
n fo
r ea
ch t
ime
band
and
tota
l
Dis
play
tot
al s
ales
by
sing
lese
lect
ion
RE
LATI
VE ST
ATI
STI
CS
TOTA
L SA
LES
by t
ime
band
in t
est
mod
efr
ee
TEC
H >
3.3.
1D
ispl
ay s
el.
coun
ter
TEC
H >
3.3.
1.1
Dis
p. s
ingl
e co
unte
rTE
CH
>3.
3.1.
1Se
lect
ion
##Se
lect
ion
##Ti
me
band
# =
###
#
TEC
H >
3.3.
1.2
Dis
p. to
tal c
ount
erSe
lect
ion
##To
tal =
###
TEC
H >
3.3
Dis
play
rel
ativ
e st
ats
TEC
H >
3.3.
2C
ount
. by
tim
e ba
nds
Tim
e ba
nd 0
÷4C
ount
er =
##
#
Com
pres
sor
Cou
nter
=
###
TEC
H >
3.3.
3D
ispl
ay f
ailu
res
TEC
H >
3.3.
4.1
Disp
. Aud
it da
taTE
CH
>3.
3.4
Disp
. coin
mec
h da
ta
TEC
H >
3.3.
4.2
Disp
lay c
ash
coun
ter
Mo
nit
ore
d f
ailu
res:
Co
mp
ress
or
Coi
n m
echa
nism
RA
M d
ata
Pro
be
CO
IN M
EC
HA
NIS
M D
AT
A(a
ccor
ding
to
prot
ocol
use
d)
Val
idat
ors
and
Exe
cutiv
eC
ashe
d an
d so
ld
BD
V A
udit
MD
B A
udit
TEC
H >
3.4
Del
ete
rela
tive
stat
s
Err.
befo
re d
isp.
Cou
nter
= #
##TE
CH
>3.
3.5
Dis
p. p
hot.
err.
cnt.
Ph
oto
cell
erro
rs:
Bef
ore
disp
ensi
ngA
fter
disp
ensi
ngP
rodu
ct n
ot d
etec
ted
Sele
ct.
N.
##C
ount
er =
###
TEC
H >
3.3.
6D
isp.
mot
. er
r. cn
t.
Mo
tor
erro
r
© by NECTA VENDING SOLUTIONS SpA
53
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
Del
ete
data
for
:S
elec
tions
Tim
e ba
nds
Fai
lure
sC
oin
mec
hani
sm d
ata
Pho
toce
ll er
rors
Mot
or e
rror
s
RE
LATI
VE ST
ATI
STI
CS
TEC
H >
3.4.
1D
elet
e pa
rtial
TEC
H >
3.4.
1.1
Del
. se
l. co
unte
rC
onfir
m?
Del
. se
l. co
unte
r
Wor
king
...
Del
. se
l. co
unte
r
TEC
H >
3.4.
2D
elet
e to
tal
Con
firm
?
Del
ete
sele
ctio
ns
Wor
king
...
Del
ete
sele
ctio
ns
TEC
H >
3.4
Del
ete
rela
tive
stat
s
TEC
H>3
.5D
isp.
cnt
. at s
tart
ON
/OFF
Dis
p. c
nt. a
t sta
rtT
he n
umbe
r of
sel
ectio
nsm
ade
are
indi
cate
d on
the
disp
lay
at m
achi
ne s
tart
-up
TOTA
L STA
TIS
TIC
S
Prin
t da
ta f
or:
Sel
ectio
nsT
ime
band
sF
ailu
res
Coi
n m
echa
nism
dat
aP
hoto
cell
erro
rsM
otor
err
ors
Hea
din
g:
Cur
rent
dat
eM
achi
ne m
odel
Sof
twar
e ed
ition
Ope
rato
r co
deM
achi
ne c
ode
Inst
alla
tion
date
RE
LATI
VE ST
ATI
STI
CS
TEC
H >
3.6.
1Pa
rtial
prin
tout
TEC
H >
3.6.
1.1
Sele
ctio
nsC
onfir
m?
Prin
t Se
lect
ions
Prin
ting.
..
Prin
t Se
lect
ions
TEC
H >
3.6.
2To
tal p
rinto
utC
onfir
m?
Tota
l prin
tout
Prin
ting.
..
Tota
l prin
tout
TEC
H >
3.7
Prin
t re
lativ
e st
ats
TEC
H >
3.6
Prin
t st
atis
tics
TEC
H >
3.7.
2To
tal p
rinto
utC
onfir
m?
Tota
l prin
tout
Prin
ting.
..
Tota
l prin
tout
Prin
ting.
..
Prin
t Se
lect
ions
Prin
ting.
..
Con
firm
?
Prin
t se
l. co
unte
rTE
CH
>3.
7.1.
1Pr
int
sel.
coun
ter
TEC
H >
3.7.
1Pa
rtial
prin
tout
TEC
H >
4Te
st
© by NECTA VENDING SOLUTIONS SpA
54
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
4Te
stTE
CH
>4.
1Te
st s
elec
tion
TEC
H >
4.2
Mot
or te
stW
ait
plea
se
Sele
ctio
n nr
.##
Sele
ctio
n nr
.##
Wai
t pl
ease
The
sel
ectio
n nu
mbe
rch
ange
s au
tom
atic
ally
TEC
H >
4.3
Auto
test
Con
firm
?
Keyp
ad t
est
Keyp
ad t
est
Pres
s 1
butto
n#
Whe
n pr
essi
ng t
he b
utto
n,th
e ne
xt b
utto
n is
pre
sent
edau
tom
atic
ally
Con
firm
?
Tem
pera
ture
tes
tTe
mpe
ratu
re t
est
Tem
p. =
12.
2 °C
Con
firm
?
Buzz
er t
est
Buzz
er t
est
Wor
king
...
Em
issi
on o
f a
serie
s of
sou
nd
s
Con
firm
?
Com
pres
sor
test
Com
pres
sor
test
ON
/OFF
OFF
ON
Con
firm
?
Sele
ctio
n te
st
Wai
t pl
ease
Sele
ctio
n nr
.##
All
sele
ctio
ns a
re a
ctiv
ated
in a
seq
uenc
e
© by NECTA VENDING SOLUTIONS SpA
55
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
Con
firm
?
Coi
n m
ech
test
Failu
re l
ist
Coi
n m
ech
test
WIT
H E
XE
CU
TIV
E O
R
BD
V C
OIN
ME
CH
AN
ISM
S
If th
e co
in m
echa
nism
com
mun
icat
es i
t di
spla
ys "
OK
"
ALT
ER
NA
TIV
ELY
WIT
H A
VALI
DA
TOR
Con
firm
?
Coi
n m
ech
test
Coi
n m
ech
test Act
ivat
ing
a lin
e of
the
valid
ator
A t
o F
Coi
n m
ech
test
Valid
. lin
e #
Line
tw
o re
mai
ns f
orap
prox
imat
ely
2 se
cond
s
Con
firm
?
Phot
ocel
l tes
tW
ITH PH
OTO
CE
LLS
DIS
CO
NN
EC
TED
ALT
ER
NA
TIV
ELY
Phot
ocel
l tes
tAb
sent
Con
firm
?
Phot
ocel
l tes
t
Failu
re l
ist
Phot
ocel
l tes
tIf
the
light
bea
m i
s in
terr
upte
dw
ithin
2.5
sec
onds
it
disp
lays
"O
K"
or
Err
or n
o pr
oduc
tIf
a fa
ilure
is
pres
ent:
Err
or a
fter
disp
ensi
ngE
rror
bef
ore
disp
ensi
ng
WIT
H PH
OTO
CE
LLS
Con
firm
?
Dis
p. c
omp'
t lo
ckD
isp.
com
p't
lock
ON
/OFF
With
dis
pens
ing
com
part
men
tlo
ck p
rese
nt
Con
firm
?
Dire
ct k
eypa
d te
stD
irect
key
pad
test
Pres
s 1
butto
n#
Whe
n pr
essi
ng t
he b
utto
n, t
he n
ext
butto
n is
pre
sent
ed a
utom
atic
ally
© by NECTA VENDING SOLUTIONS SpA
56
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H >
5M
isce
llane
ous
TEC
H >
5.1
Mac
hine
inf
oTE
CH
5.1
.1In
stal
latio
n da
teD
ate:
##/#
#/##
d
#C
onfir
m?
TEC
H>5
.1.2
Prog
. m
achi
ne c
ode
TEC
H>5
.2In
itial
ise
DB
Initi
alis
e D
BIn
itial
ise
DB
Wor
king
...
Whe
n co
nfirm
ing,
the
curr
ent
date
will
be
set
asth
e in
stal
latio
n da
te
8-di
git
num
ber
iden
tifyi
ng t
hem
achi
ne
TEC
H>5
.1.3
Prog
. op
erat
or c
ode
Prog
. m
achi
ne c
ode
Cod
e:=
. ##
+##
##
Prog
. op
erat
or c
ode
Cod
e:=
. ##
+##
##
6-di
git
num
ber
to i
dent
ifygr
oups
of
vend
ing
mac
hine
s
Con
firm
?
Star
t
Init
ialis
e d
atab
ases
Cou
ntry Co
untry
nam
e
Lang
uage La
ngua
ge
Co
un
trie
s:Ita
lyG
reat
Brit
ain
Fra
nce
- S
pain
Bra
zil
- P
olan
dB
elgi
um
Lan
gu
ages
:Ita
lian
Eng
lish
Fre
nch
- S
pani
shP
ortu
gues
eF
lem
ish
TEC
H>5
.3EV
ADTS
TEC
H>5
.3.1
Pass
Cod
ePa
ss C
ode
Cod
e##
####
TEC
H>5
.3.2
Secu
rity
Cod
eSe
curit
y C
ode
Cod
e##
####
TEC
H>5
.3.3
Con
nect
ion
Wai
t pl
ease
TEC
H>6
GS
M
© by NECTA VENDING SOLUTIONS SpA
57
Tec
hn
icia
n m
enu
- S
um
mar
y
0407 239 - 00
CO
NF
IRM
DA
TA
/C
ON
FIR
M F
UN
CT
ION
DE
LET
E D
AT
A/
EX
IT F
UN
CT
ION
PR
EV
IOU
S F
UN
CT
ION
/D
EC
RE
AS
E D
AT
A U
NIT
(-1
)N
EX
T F
UN
CT
ION
/IN
CR
EA
SE
DA
TA
UN
IT (
+1)
TEC
H>6
GS
MTE
CH
>6.
1PI
N
TEC
H>6
.2G
SM p
re-a
larm
s
Pin
cod
e as
sign
ed t
o th
em
odem
Num
ber
of p
rodu
cts
afte
rw
hich
an
"end
ing
prod
uct"
pre-
alar
m i
s se
nt
TEC
H>6
.2.2
Rese
t pr
e-ala
rm c
ount
.
Prod
uct
nam
eN
r. =
####
Res
ettin
g co
unt
of d
ispe
nsed
pro
du
cts
Set
thre
shol
ds
Prod
uct n
ame
TEC
H>6
.3N
umbe
r in
Ban
k
TEC
H>1
Failu
res
TEC
H >
6.1
Pin
=##
####
TEC
H>6
.2.1
Set
thre
shol
ds
Rese
t pr
e-ala
rm c
ount
.
Lang
uage
Rese
t pr
e-ala
rm c
ount
.
Con
firm
?
TEC
H>6
.2.3
Thre
shol
d as
soci
atio
nPr
e-al
arm
Sele
ctio
n #
##
##
Pre-
alar
m 6
Tra
y
Ass
ocia
tion
of t
hres
hold
s to
5 se
lect
ions
and
2 t
rays
##
Pre-
alar
m 1
Sele
ctio
n
#
TEC
H>6
.3N
r. in
Ban
k
1 to
7 i
dent
ifyin
gS
lave
GS
M0
iden
tifyi
ngM
ast
er
GS
M
© by NECTA VENDING SOLUTIONS SpA 0407 239-00
58
INITIALS DESCRIPTION
WIRING DIAGRAM LEGEND
INITIALS DESCRIPTION
CCB CAN BUS CONNECTOR
CF FILTER CONDENSER
CM0-9 VENDING MOTOR CAM
CMV DISPENSING COMPARTMENT MOTOR CAM
D DIODE
EX CONNECTOR FOR EXECUTIVE COIN MECH
FA RADIO INTERFERENCE SUPPRESSOR
FD PHOTODIODE
FT PHOTOTRANSISTOR
IP DOOR SWITCH
ISA OPEN HATCH SWITCH
LCD LIQUID CRYSTAL DISPLAY
M1-... RELEASE MOTOR
MBV DISPENSING COMPARTMENT LOCK MOTOR
MDB CONNECTOR FOR MDB COIN MECH
MIP PROGRAMMING ACCESS MICROSWITCH
MS1 HATCH MOTOR MICROSWITCH
MUR COMPRESSOR
MVT FAN
NTC1-. TEMPERATURE PROBE
PIP PROGRAMMING ACCESS BUTTON
R ANTI-CONDENSATION HEATING ELEMENT
RS232 SERIAL PORT
RT BALLAST
SOR OUT/R BOARD
SP PUSH-BUTTON BOARD
ST STARTER
SUC C.P.U. BOARD
TR TRANSFORMER
TX.... DELAYED FUSE (X=COURRENT)
© by NECTA VENDING SOLUTIONS SpA NOTE
SnakkyLux
sx41900
SnakkyMax
sx41900
SnakkyLux
Sx42000
SnakkyMax
Sx42000
© by NECTA VENDING SOLUTIONS SpA NOTE
© by NECTA VENDING SOLUTIONS SpA NOTE
© by NECTA VENDING SOLUTIONS SpA NOTE
EDITION 2004 07 CODE: H 239U 00
The Manufacturer reserves the right to modify, without prior notice, the characteristics of the equipment described in thispublication; and further declines to accept any responsibility for any inaccuracies contained in this publication which can beascribed to printing and/or transcription errors.All instructions, drawings, tables and information contained in this publication are confidential and can neither be repro-duced completely or in part, nor be transmitted to third parties without the written permit of the Manufacturer, who has thesole ownership.