Post on 02-Dec-2015
description
transcript
CHASSIS
SERVICE MANUAL
SPECIFICATIONS
CPD-G500
G1
US ModelCanadian Model
AEP ModelChassis No. SCC-L22C-A
S.Hemisphere ModelChassis No. SCC-L22G-A
Equator ModelChassis No. SCC-L22F-A
TRINITRON® COLOR COMPUTER DISPLAY
CRT 0.24 mm aperture grille pitch 21 inches measured diagonally 90-degree deflectionFD Trinitron
Viewable image size Approx. 403.8 × 302.2 mm (w/h) (16 × 12 inches) 19.8" viewing image
ResolutionMaximum Horizontal: 2048 dots
Vertical: 1536 linesRecommended Horizontal: 1600 dots
Vertical: 1200 linesStandard image area Approx. 388 × 291 mm (w/h)
(15 3/8 × 11 1/2 inches) or Approx. 364 × 291 mm (w/h) (14 3/8 × 11 1/2 inches)
Deflection frequency* Horizontal: 30 to 121 kHzVertical: 48 to 160 Hz
AC input voltage/current 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 APower consumption Approx. 145 WDimensions Approx. 497 × 480 × 478 mm (w/h/d)
(19 5/8 × 19 × 18 7/8 inches)Mass Approx. 32 kg (70 lb 9 oz)Plug and Play DDC1/2B/2Bi, GTF**
* Recommended horizontal and vertical timing condition• Horizontal sync width duty should be more than 4.8% of total
horizontal time or 0.8 µs, whichever is larger.• Horizontal blanking width should be more than 2.3 µsec.• Vertical blanking width should be more than 450 µsec.
** If the input signal is Generalized Timing Formula (GTF) compliant, the GTF feature of the monitor will automatically provide an optimal image for the screen.
Design and specifications are subject to change without notice.
CPD-G500
– 2 –
LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part hav-
ing a return to chassis, must not exceed 0.5 mA (500 microam-
peres).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to
use these instruments.
2. A battery-operated AC milliammeter. The Data Precision
245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOMs that are suitable. Nearly all
battery operated digital multimeters that have a 2 V AC
range are suitable. (See Fig. A)
WARNING!!NEVER TURN ON THE POWER IN A CONDITION INWHICH THE DEGAUSS COIL HAS BEEN REMOVED.
SAFETY-RELATED COMPONENT WARNING!!COMPONENTS IDENTIFIED BY SHADING AND MARK¡ ON THE SCHEMATIC DIAGRAMS, EXPLODEDVIEWS AND IN THE PARTS LIST ARE CRITICAL FORSAFE OPERATION. REPLACE THESE COMPONENTSWITH SONY PARTS WHOSE PART NUMBERS AP-PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-MENTS PUBLISHED BY SONY. CIRCUIT ADJUST-MENTS THAT ARE CRITICAL FOR SAFE OPERATIONARE IDENTIFIED IN THIS MANUAL. FOLLOW THESEPROCEDURES WHENEVER CRITICAL COMPONENTSARE REPLACED OR IMPROPER OPERATION IS SUS-PECTED.
AVERTISSEMENT!!NE JAMAIS METTRE SOUS TENSION QUAND LABOBINE DE DEMAGNETISATION EST ENLEVÉE.
ATTENTION AUX COMPOSANTS RELATIFS À LASÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ETUNE MARQUE ¡ SONT CRITIQUES POUR LA SÉCURITÉ.NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LENUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONTL’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DUFONCTIONNEMENT SONT IDENTIFIÉS DANS LEPRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORSDE CHAQUE REMPLACEMENT DE COMPOSANTS CRI-TIQUES, OU LORSQU’UN MAUVAIS FONCTIONNEMENTEST SUSPECTÉ.
After correcting the original service problem, perform the fol-
lowing safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly tran-
sistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values.
Make sure your instruments are accurate; be suspicious of
your HV meter if sets always have low HV.
8. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for AC
Leakage. Check leakage as described below.
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY CHECK-OUT
1.5 kΩ0.15 µFACVoltmeter(0.75 V)
To Exposed MetalParts on Set
Earth Ground
CPD-G500
– 3 –
This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer(s), the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard.
If the 1 (power) indicator is green
1 Remove any plugs from the video input 1 and 2 connectors, or turn off the connected computer(s).
2 Press the 1 (power) button twice to turn the monitor off and then on.
3 Move the control button , for 2 seconds before the monitor enters power saving mode.
If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cables and check the condition of your computer(s).
If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition.
If the 1 (power) indicator is flashing orange
Press the 1 (power) button twice to turn the monitor off and then on.If the 1 (power) indicator lights up green, the monitor is working properly.
If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board.
MENU
RESET INPUT HD15 BNC
1 (power) indicator
MENU
Power saving functionThis monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below.
* “Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency.
** When your computer enters a power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters a power saving mode.
Power mode Power consumption 1 (power) indicator
normal operation
≤ 145 W green
1 standby ≤ 100 W green and orange alternate
2 suspend(sleep)*
≤ 15 W green and orange alternate
3 active off**(deep sleep)*
Approx. 1 W orange
power off 0 W off
DIAGNOSIS
CPD-G500
– 4 –
TIMING SPECIFICATION
MODE AT PRODUCTION MODE 1 MODE 2 MODE 3 MODE 4
RESOLUTION 1600 X 1200 1920 X 1440 1800 X 1440 1800 X 1350
CLOCK 229.500 MHz 297.000 MHz 299.436 MHz 300.000 MHz
— HORIZONTAL —
H-FREQ 106.250 kHz 112.500 kHz 120.740 kHz 120.968 kHz
usec usec usec usec
H. TOTAL 9.412 8.889 8.282 8.267
H. BLK 2.440 2.424 2.271 2.267
H. FP 0.279 0.485 0.668 0.480
H. SYNC 0.837 0.754 0.481 0.667
H. BP 1.325 1.185 1.122 1.120
H. ACTIV 6.972 6.465 6.011 6.000
— VERTICAL —
V. FREQ(HZ) 85.000 Hz 75.000 Hz 80.120 Hz 85.009 Hz
lines lines lines lines
V. TOTAL 1250 1500 1507 1423
V. BLK 50 60 67 73
V. FP 1 1 1 1
V. SYNC 3 3 3 3
V. BP 46 56 63 69
V. ACTIV 1200 1440 1440 1350
— SYNC —
INT(G) NO NO NO NO
EXT(H/V)/POLARITY YES P/P YES P/P YES P/P YES P/P
EXT(CS) /POLARITY NO NO NO NO
INT/NON INT NON INT NON INT NON INT NON INT
99.07.02 VER.
CPD-G500
– 5 –
Note: Hand degauss must be used on stand-by or power-off condition.
This model has an automatic earth magnetism correction function by using an earth
magnetism sensor and a LCC coil. When using a hand degauss while monitor (LCC
coil) is being operated, it sometimes gets magnetized, and the system may not work
properly as a result.
TABLE OF CONTENTS
Section Title Page
1. GENERAL ................................................................. 1-1
2. DISASSEMBLY2-1. Cabinet Removal ............................................... 2-1
2-2. D Board Removal .............................................. 2-1
2-3. G Board Removal .............................................. 2-2
2-4. A Board, I/O Terminal Board Assembly
Removal ............................................................. 2-2
2-5. N Board Removal .............................................. 2-3
2-6. Service Position .................................................. 2-3
2-7. Bezel Assembly, H1 Board Removal ................ 2-4
2-8. Picture Tube Removal ....................................... 2-4
2-9. J Board Removal ............................................... 2-5
2-10. Harness Location ............................................... 2-6
3. SAFETY RELATED ADJUSTMENT ............. 3-1
4. ADJUSTMENTS ..................................................... 4-1
5. DIAGRAMS5-1. Block Diagrams .................................................. 5-1
5-2. Frame Shcematic Diagram ................................. 5-7
5-3. Circuit Boards Location ..................................... 5-9
5-4. Schematic Diagrams and Printed Wiring
Boards ................................................................. 5-9
(1) Schematic Diagram of A Board ........................ 5-11
(2) Schematic Diagrams of H1, J Boards ............... 5-17
(3) Schematic Diagram of D Board ........................ 5-19
(4) Schematic Diagrams of N (a, b, c) Board .. 5-23
(5) Schematic Diagram of G Board ........................ 5-31
5-5. Semiconductors ................................................. 5-35
6. EXPLODED VIEWS6-1. Chassis ............................................................... 6-1
6-2. Picture Tube ...................................................... 6-2
6-3. Packing Materials ............................................... 6-3
7. ELECTRICAL PARTS LIST ............................ 7-1
SECTION 1
GENERAL
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
1-1
4
Precautions
Warning on power connections• Use the supplied power cord. If you use a different power cord,
be sure that it is compatible with your local power supply.For the customers in the U.S.A.If you do not use the appropriate cord, this monitor will not conform to mandatory FCC standards.
• Before disconnecting the power cord, wait at least 30 seconds after turning off the power to allow the static electricity on the screen’s surface to discharge.
• After the power is turned on, the screen is demagnetized (degaussed) for about 2 seconds. This generates a strong magnetic field around the screen which may affect data stored on magnetic tapes and disks placed near the monitor. Be sure to keep magnetic recording equipment, tapes, and disks away from the monitor.
InstallationDo not install the monitor in the following places:• on surfaces (rugs, blankets, etc.) or near materials (curtains,
draperies, etc.) that may block the ventilation holes• near heat sources such as radiators or air ducts, or in a place
subject to direct sunlight• in a place subject to severe temperature changes• in a place subject to mechanical vibration or shock• on an unstable surface• near equipment which generates magnetism, such as a
transformer or high voltage power lines• near or on an electrically charged metal surface
Maintenance• Clean the screen with a soft cloth. If you use a glass cleaning
liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the screen’s coating.
• Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube.
• Clean the cabinet, panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzene.
TransportationWhen you transport this monitor for repair or shipment, use the original carton and packing materials.
Use of the tilt-swivelThis monitor can be adjusted within the angles shown below. To find the center of the monitor’s turning radius, align the center of the monitor’s screen with the centering dots on the stand.Hold the monitor at the bottom with both hands when you turn it horizontally or vertically. Be careful not to pinch your fingers at the back of the monitor when you tilt the monitor up vertically.
The equipment should be installed near an easily accessible outlet.
Example of plug types
for 100 to 120 V AC for 200 to 240 V AC
90˚
5˚
90˚
15˚
Centering dots
5
US
Identifying parts and controlsSee the pages in parentheses for further details.
1 RESET (reset) button (page 16)This button resets the adjustments to the factory settings.
2 INPUT (input) switch (page 8)This switch selects the HD15 or BNC video input signal.
3 Control button (page 10)The control button is used to display the menu and make adjustments to the monitor, including brightness and contrast adjustments.
4 1 (power) switch and indicator (pages 7, 16, 20)This button turns the monitor on and off. The power indicator lights up in green when the monitor is turned on, and either flashes in green and orange, or lights up in orange when the monitor is in power saving mode.
5 AC IN connector (page 7)This connector provides AC power to the monitor.
6 Video input 1 connector (HD15) (y1) (page 6)This connector inputs RGB video signals (0.700 Vp-p, positive) and sync signals.
* DDC (Display Data Channel) is a standard of VESA.
7 Video input 2 connector (BNC) (y2) (page 6)This connector inputs RGB video signals (0.700 Vp-p, positive) and sync signals.
MENU
RESET INPUT HD15 BNC
MENU
RESET INPUT HD15 BNC
R G B HD VD
(HD15) (BNC)
AC IN
RearFront
rear side
forward side forward side
rear side
Pin No. Signal
1 Red
2 Green(Sync on Green)
3 Blue
4 ID (Ground)
5 DDC Ground*
6 Red Ground
7 Green Ground
8 Blue Ground
9 DDC + 5V*
10 Ground
11 ID (Ground)
12 Bi-Directional Data (SDA)*
13 H. Sync
14 V. Sync
15 Data Clock (SCL)*
5 4 3 2 1678910
1112131415
1-2
6
SetupBefore using your monitor, check that the following accessories are included in your carton:• Power cord (1)• HD15 video signal cable (1)• Macintosh adapter (1)• Windows Monitor Information Disk (1)• Warranty card (1)• Notes on cleaning the screen’s surface (1)• This instruction manual (1)
Step 1:Connect your monitor to your computer
Turn off the monitor and computer before connecting.
Notes• Do not touch the pins of the video signal cable connector as this might
bend the pins.• When connecting the video signal cable, check the alignment of the
HD15 connector. Do not force the connector in the wrong way or the pins might bend.
x Connecting to an IBM PC/AT or compatible computer
x Connecting to a Macintosh or compatible computer
* Connect the supplied Macintosh adapter to the computer before connecting the cable. This adapter is compatible with Macintosh LC, Performa, Quadra, Power Macintosh and Power Macintosh G3 series computers (sold before January, 1999). If you are connecting to a Power Macintosh G3 series that sold after January 1999, you will need a different adapter (not supplied). Macintosh II series and some older versions of PowerBook models may need an adapter with micro switches (not supplied).
x Connecting to the five BNC connectors
* Connect the cables from left to right in the following order: Red-Green-Blue-HD-VD.
NotePlug & Play (DDC) does not apply to the five BNC connectors. If you want to use Plug & Play, connect your computer to the HD15 connector using the supplied video signal cable.
R G B HD VD
(HD15) (BNC)
AC IN
HD15 video signal cable (supplied)
to video output
IBM PC/AT or compatible computer
to HD15
R G B HD VD
(HD15) (BNC)
AC IN
to HD15
Macintosh adapter (supplied)*
Macintosh or compatible computer
to video output
HD15 video signal cable (supplied)
R G B HD VD
(HD15) (BNC)
AC IN
to VIDEO IN R/G/B
to SYNC IN HD/VD
Refer to the preceding examples to connect to your computer. video signal cable
(SMF-400, not supplied)*
7
US
Step 2:Connect the power cordWith the monitor and computer switched off, first connect the power cord to the monitor, then connect it to a power outlet.
Step 3:Turn on the monitor and computer
First turn on the monitor, then turn on the computer.
The installation of your monitor is complete.If necessary, use the monitor’s controls to adjust the picture.
If no picture appears on your screen• Check that the monitor is correctly connected to the computer.• If NO INPUT SIGNAL appears on the screen, try changing the
input signal (page 8), and confirm that your computer’s graphic board is completely seated in the correct bus slot.
• If you are replacing an old monitor with this model and OUT OF SCAN RANGE appears on the screen, reconnect the old monitor. Then adjust the computer’s graphic board so that the horizontal frequency is between 30 – 121 kHz, and the vertical frequency is between 48 – 160 Hz.
For more information about the on-screen messages, see “Trouble symptoms and remedies” on page 18.
For customers using Windows 95/98To maximize the potential of your monitor, install the new model information file from the supplied Windows Monitor Information Disk onto your PC.This monitor complies with the “VESA DDC” Plug & Play standard. If your PC/graphics board complies with DDC, select “Plug & Play Monitor (VESA DDC)” or this monitor’s model name as the monitor type in the “Control Panel” of Windows 95/98. If your PC/graphics board has difficulty communicating with this monitor, load the Windows Monitor Information Disk and select this monitor’s model name as the monitor type.
For customers using Windows NT4.0Monitor setup in Windows NT4.0 is different from Windows 95/98 and does not involve the selection of monitor type. Refer to the Windows NT4.0 instruction manual for further details on adjusting the resolution, refresh rate, and number of colors.
Adjusting the monitor’s resolution and color numberAdjust the monitor’s resolution and color number by referring to your computer’s instruction manual. The color number may vary according to your computer or video board. The color palette setting and the actual number of colors are as follows:• High Color (16 bit) t 65,536 colors• True Color (24 bit) t about 16.77 million colorsIn true color mode (24 bit), speed may be slower.
R G B HD VD
(HD15) (BNC)
AC IN
to AC IN
to a power outletpower cord (supplied)
1-3
8
Selecting the on-screen menu language (LANG)English, French, German, Spanish, Italian, Dutch, Swedish, Russian and Japanese versions of the on-screen menus are available. The default setting is English.
1 Press the center of the control button.See page 10 for more information on using the control button.
2 Move the control button to highlight LANG and press the center of the control button again.
3 Move the control button m/M to select a language.• ENGLISH• FRANÇAIS: French• DEUTSCH: German• ESPAÑOL: Spanish• ITALIANO: Italian• NEDERLANDS: Dutch• SVENSKA: Swedish• : Russian• : Japanese
To close the menuPress the center of the control button once to return to the main MENU, and twice to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds.
To reset to EnglishPress the RESET button while the LANGUAGE menu is displayed on the screen.
Selecting the input signalYou can connect two computers to this monitor using the HD15 and BNC connectors. To select one of the two computers, use the INPUT switch.
Move the INPUT switch.The selected connector appears on the screen for 3 seconds.
“HD15” or “BNC” appears on the screen.
NoteIf no signal is input to the selected connector, NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters the power saving mode. If this happens, switch to the other connector.
MENUMENUMENU
EXIT
CENTER
SIZE
GEOM
SCREEN
COLOR
LANG
CONV
OPTION
OK
MENU
ENGL I SHFRANÇA I SDEUTSCHESPAÑOLI TA L I ANONEDERL ANDSSVENSKA
L ANGUAGE
INPUT HD15 BNC
9
US
Customizing Your MonitorYou can make numerous adjustments to your monitor using the on-screen menu.
Navigating the menuPress the center of the control button to display the main MENU on your screen. See page 10 for more information on using the control button.
Use the control button to select one of the following menus. x Displaying the current input signalThe horizontal and vertical frequencies of the current input signal are displayed in the main MENU. If the signal matches one of this monitor’s factory preset modes, the resolution is also displayed.
1 CENTER (page 11)Selects the CENTER menu to adjust the picture’s centering, size or zoom.
2 SIZE (page 11)Selects the SIZE menu to adjust the picture’s size, centering or zoom.
3 GEOM (page 12)Select the GEOM menu to adjust the picture’s rotation and shape.
4 COLOR (page 13)Select the COLOR menu to adjust the picture’s color temperature. You can use this to match the monitor’s colors to a printed picture’s colors.
5 SCREEN (page 13)Select the SCREEN menu to adjust the picture’s quality. You can adjust the landing and moire cancellation effect.
MENUMENU
EXIT
CENTER
SIZE
GEOM
SCREEN
COLOR
LANG
CONV
OPTION
OKMENU
AUTO
ON
S I ZE / CENTER
AUTO
ON
S I ZE / CENTER
2 6
GEOMETRY
EASY EXPERT s BGR
5 0 0 0 K 6 5 0 0 K 9 3 0 K05 0 K00
I MAGERESTORAT I ON ON
COLOR
L AND I NG
2 6
SCREEN
6 CONV (page 12)Select the CONV menu to adjust the picture’s horizontal and vertical convergence.
7 LANG (page 8)Select LANG to choose the on-screen menu’s language.
8 OPTION (page 15)Select OPTION to adjust the monitor’s options. The options include:• degaussing the screen• changing the on-screen menu
position• locking the controls
9 EXITSelect EXIT to close the menu.
TOPBOT
2 6
CONVERGENCE
ENGL I SHFRANÇA I SDEUTSCHESPAÑOLI TA L I ANONEDERL ANDSSVENSKA
L ANGUAGE
DEGAUSS
ON
OPT ION
MENUMENU
EXIT
CENTER
SIZE
GEOM
SCREEN
COLOR
LANG
CONV
OPTION
OK
68 . 7kHz / 85Hz1024 768
the horizontal and vertical frequencies of the current input signal
the resolution of the current input signal
1-4
10
x Using the control button
1 Display the main MENU.Press the center of the control button to display the main MENU on your screen.
2 Select the menu you want to adjust.Highlight the desired menu by moving the control button towards the rear to go up (M), towards the front to go down (m), and left (<) or right (,) to move sideways.
3 Adjust the menu.Move the control button left (
<
) or right (
,
) to make the adjustment.
4
Close the menu.
Press the center of the control button once to return to the main MENU, and twice to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds.
x
Resetting the adjustments
Press the RESET button. See page 16 for more information on resetting the adjustments.
Adjusting the brightness and contrast
Brightness and contrast adjustments are made using a separate BRIGHTNESS/CONTRAST menu.These settings are stored in memory for the signals from the currently selected input connector.
1
Move the control button in any direction.
The BRIGHTNESS/CONTRAST menu appears on the screen.
2
Move the control button
m
/
M
to adjust the brightness ( ), and
<
/
,
to adjust the contrast (
6
).
If you are using the sRGB mode
If you selected the sRGB mode in the COLOR menu, the following BRIGHTNESS/CONTRAST menu appears on the screen.
For more information about using the sRGB mode, see “Adjusting the color of the picture (COLOR)” on page 13.
The menu automatically disappears after about 3 seconds.
MENU
MENU MENU
REAR
FRONT
MENU
MENU
RESET
2 6 2 6
BR I GHTNESS / CONTRAST
5 6 7 6
s RGB : 5 6 7 6
BR I GHTNESS / CONTRAST
11
US
Automatically sizing and centering the picture (AUTO)You can easily adjust the picture to fill the screen by using the (AUTO) item in the SIZE/CENTER menu.
1 Press the center of the control button.The main MENU appears on the screen.
2 Move the control button to highlight SIZE or CENTER and press the center of the control
button again.The SIZE/CENTER menu appears on the screen.
3 First move the control button m/M
to select (AUTO). Then move the control button
,
.
The picture automatically fills the screen.
Notes
• This function is intended for use with a computer running Windows or similar graphic user interface software that provides a full-screen picture. It may not work properly if the background color is dark or if the input picture does not fill the screen to the edges (such as an MS-DOS prompt).
• Pictures with an aspect ratio of 5:4 (resolution: 1280
×
1024, 1600
×
1280) are displayed at their actual resolution and do not fill the screen to the edges.
• The displayed image moves for a few seconds while this function is performed. This is not a malfunction.
Adjusting the size of the picture (SIZE)
This setting is stored in memory for the current input signal.
1
Press the center of the control button.
The main MENU appears on the screen.
2
Move the control button to highlight SIZE and press the center of the control button again.
The SIZE/CENTER menu appears on the screen.
3
First move the control button
m
/
M
to select for horizontal adjustment, or for vertical adjustment. Then move the control button
<
/
,
to adjust the size.
Adjusting the centering of the picture (CENTER)
This setting is stored in memory for the current input signal.
1
Press the center of the control button.
The main MENU appears on the screen.
2
Move the control button to highlight CENTER and press the center of the control button again.
The SIZE/CENTER menu appears on the screen.
3
First move the control button
m
/
M
to select for horizontal adjustment, or for vertical adjustment. Then move the control button
<
/
,
to adjust the centering.
Enlarging or reducing the picture (ZOOM)
This setting is stored in memory for the current input signal.
1
Press the center of the control button.
The main MENU appears on the screen.
2
Move the control button to highlight SIZE or CENTER and press the center of the control
button again.
The SIZE/CENTER menu appears on the screen.
3
Move the control button
m
/
M
to select (zoom), and move
<
/
,
to enlarge or reduce the picture.
Note
Adjustment stops when either the horizontal or vertical size reaches its maximum or minimum value.
1-5
12
Adjusting the shape of the picture (GEOM)
The GEOM settings allow you to adjust the rotation and shape of the picture.The (rotation) setting is stored in memory for all input signals. All other settings are stored in memory for the current input signal.
1 Press the center of the control button.The main MENU appears on the screen.
2 Move the control button to highlight GEOM and press the center of the control button again.The GEOMETRY menu appears on the screen.
3 First move the control button m/M to select the desired adjustment item. Then move the control button </
,
to make the adjustment.
Adjusting the convergence (CONV)
The CONV settings allow you to adjust the quality of the picture by controlling the convergence. The convergence refers to the alignment of the red, green, and blue color signals.If you see red or blue shadows around letters or lines, adjust the convergence.These settings are stored in memory for all input signals.
1
Press the center of the control button.
The main MENU appears on the screen.
2
Move the control button to highlight CONV and press the center of the control button again.
The CONVERGENCE menu appears on the screen.
3
First move the control button
m
/
M
to select the desired adjustment item. Then move the control button
<
/
,
to make the adjustment.
Select To
rotate the picture
expand or contract the picture sides
shift the picture sides to the left or right
adjust the picture width at the top of the screen
shift the picture to the left or right at the top of the screen
Select To
horizontally shift red or blue shadows
vertically shift red or blue shadows
TOP
V CONVER TOP
vertically shift red or blue shadows at the top of the screen
BOT
V CONVER BOTTOM
vertically shift red or blue shadows at the bottom of the screen
13
US
Adjusting the quality of the picture (SCREEN)The SCREEN settings allow you to adjust the quality of the picture by controlling the moire and landing.• If the color is irregular at the corners of the screen, adjust the
landing.• If elliptical or wavy patterns appear on the screen, cancel the
moire.The CANCEL MOIRE and MOIRE ADJUST settings are stored in memory for the current input signal. All other settings are stored in memory for all input signals.
1 Press the center of the control button.The main MENU appears on the screen.
2 Move the control button to highlight SCREEN and press the center of the control button again.The SCREEN menu appears on the screen.
3 First move the control button m/
M
to select the desired adjustment item. Then move the control button
<
/
,
to make the adjustment.
• Moire is a type of natural interference which produces soft, wavy lines on your screen. It may appear due to interference between the pattern of the picture on the screen and the phosphor pitch pattern of the monitor.
Note
The picture may become fuzzy when CANCEL MOIRE is set to ON.
Adjusting the color of the picture (COLOR)
The COLOR settings allow you to adjust the picture’s color temperature by changing the color level of the white color field. Colors appear reddish if the temperature is low, and bluish if the temperature is high. This adjustment is useful for matching the monitor’s color to a printed picture’s colors.
1
Press the center of the control button.
The main MENU appears on the screen.
2
Move the control button to highlight COLOR and press the center of the control button again.
The COLOR menu appears on the screen.
3
Move the control button
<
/
,
to select the adjustment mode.
There are three types of adjustment modes, EASY, EXPERT and sRGB.
4
First move the control button
m
/
M
to select the desired adjustment item. Then move the control button
<
/
,
to make the adjustment.
Adjust the selected mode according to the following instructions.
EASY mode
1
Move the control button
m
/
M
to select the color temperature row
1
. Then move the control button
<
/
,
to select a color temperature.
The preset color temperatures are 5000K, 6500K, and 9300K. Since the default setting is 9300K, the whites will change from a bluish hue to a reddish hue as the temperature is lowered to 6500K and 5000K.
2
If necessary, fine tune the color temperature.Move the control button
m
/
M
to select the color temperature row
2
. Then move the control button
<
/
,
to fine tune the color temperature.
If you fine tune the color temperature, the new color settings are stored in memory for each of the three color temperatures and item
1
of the on-screen menu changes as follows.• [5000K]
t
[ 1]• [6500K]
t
[ 2]• [9300K]
t
[ 3]
Select To
LANDING
reduce any color irregularities in the screen’s top left corner to a minimum.
LANDING
reduce any color irregularities in the screen’s top right corner to a minimum.
LANDING
reduce any color irregularities in the screen’s bottom left corner to a minimum.
LANDING
reduce any color irregularities in the screen’s bottom right corner to a minimum.
CANCEL MOIRE*
turn the moire cancellation function ON or OFF.
(MOIRE ADJUST) appears in the menu when you select ON.
MOIRE ADJUST
adjust the degree of moire cancellation until the moire is at a minimum.
Example of moire
EASY EXPERT s BGR
5 0 0 0 K 6 5 0 0 K 9 3 0 K05 0 K00
I MAGERESTORAT I ON ON
COLOR
(continued)
1-6
14
EXPERT modeYou can make additional adjustments to the color in greater detail by selecting the EXPERT mode.
1 Move the control button m/M to select the color temperature row 1. Then move the control button </, to select a color temperature.
2 Move the control button m
/
M
to select the adjustment item
2
. Then move the control button
<
/
,
to adjust the BIAS (black level).
This adjusts the dark areas of an image.
3
Move the control button
m
/
M
to select the adjustment item
3
. Then move the control button
<
/
,
to adjust the GAIN (white level).
This adjusts the light areas of an image.
You can adjust the R (red), G (green), B (blue) component of the input signal when making changes to items
2
and
3
.
If you fine tune the color temperature, the new color settings are stored in memory for each of the three color temperatures and item
1
of the on-screen menu change as follows.• [5000K]
t
[ 1]• [6500K]
t
[ 2]• [9300K]
t
[ 3]
Setting the color temperature for each of the video input connectors
You can set the fine tuning of the color temperature in EASY or EXPERT mode for each of the video input connectors (HD15 and BNC).
1
Select the same adjustment mode and color temperature in the COLOR menu for both HD15 and BNC.
2
Fine tune the color temperature in each menu for HD15 and BNC.
The settings are stored in memory for each of the HD15 and BNC connectors.
For information on how to select the connector, see page 8.
sRGB mode
The sRGB color setting is an industry standard color space protocol designed to correlate the displayed and printed colors of sRGB compliant computer products. To adjust the colors to the sRGB profile, simply select the sRGB mode in the COLOR menu. However, in order to display the sRGB colors correctly (
γ
=2.2, 6500K), you must set your computer to the sRGB profile and adjust the brightness ( ) and contrast (
6
) to the numbers shown in the menu. For information on how to change the brightness ( ) and contrast (
6
), see page 10.
Note
Your computer and other connected products (such as a printer), must be sRGB compliant.
EASY EXPERT s BGR
5 0 0 0 K 6 5 0 0 K 9 3 0 K0R B I AS 05G B I AS 05B B I AS 05R GA I N 05G GA I N 05B GA I N 05
COLOR
EASY EXPERT s BGR
: 5 6 : 7 6 FOR s BGR
I MAGERESTORAT I ON ON
COLOR
15
US
Restoring the color from the EASY or sRGB menusThe colors of most display monitors tend to gradually lose brilliance over several years of service. The IMAGE RESTORATION feature found in the EASY and sRGB menus allows you to restore the color to the original factory quality levels. The explanation below explains how to restore the monitor’s color from the EASY menu.
1 Move the control button </, to select EASY or sRGB mode.
2 First move the control button m/M
to select (IMAGE RESTORATION). Then move the control button
,
.
The picture disappears while the color is being restored (about 2 seconds). After the color is restored, the picture reappears on the screen again.
Notes
• Before using this feature, the monitor must be in normal operation mode (green power indicator on) for at least 30 minutes. If the monitor goes into power saving mode, you must return the monitor to normal operation mode and wait for 30 minutes for the monitor to be ready. You may need to adjust your computer’s power saving settings to keep the monitor in normal operation mode for the full 30 minutes. If the monitor is not ready, the following message will appear.
• The monitor may gradually lose its ability to perform this function due to the natural aging of the picture tube.
Additional settings (OPTION)
You can manually degauss (demagnetize) the monitor, change the menu position, and lock the controls.
1
Press the center of the control button.
The main MENU appears on the screen.
2
Move the control button to highlight OPTION and press the center of the control button again.
The OPTION menu appears on the screen.
3
Move the control button
m
/
M
to select the desired adjustment item.
Adjust the selected item according to the following instructions.
Degaussing the screen
The monitor is automatically demagnetized (degaussed) when the power is turned on.
To manually degauss the monitor, first move the control button
m
/
M
to select (DEGAUSS). Then move the control button
,
.
The screen is degaussed for about 2 seconds. If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result.
Changing the menu’s position
Change the menu’s position if it is blocking an image on the screen.
To change the menu’s on-screen position, first move the control button
m
/
M
to select (OSD H POSITION) for horizontal adjustment, or (OSD V POSITION) for vertical adjustment. Then move the control button
<
/
,
to shift the on-screen menu.
Locking the controls
To protect adjustment data by locking the controls, first move the control button
m
/
M
to select (CONTROL LOCK). Then move the control button
,
, to select ON.
Only the
1
(power) switch, EXIT, and (CONTROL LOCK) of the OPTION menu will operate. If any other items are selected, the mark appears on the screen.
To cancel the control lock
Repeat the procedure above and set (CONTROL LOCK) to OFF.
EASY EXPERT s BGR
5 0 0 0 K 6 5 0 0 K 9 3 0 K05 0 K00
I MAGERESTORAT I ON
AVA I L AB L EAF TER WARM UP
COLOR
1-7
16
Resetting the adjustmentsThis monitor has the following three reset methods. Use the RESET button to reset the adjustments.
Resetting a single adjustment itemUse the control button to select the adjustment item you want to reset, and press the RESET button.
Resetting all of the adjustment data for the current input signalPress the RESET button when no menu is displayed on the screen. Note that the following items are not reset by this method:• on-screen menu language (page 8)• adjustment mode in the COLOR menu (EASY, EXPERT,
sRGB) (page 13)• on-screen menu position (page 15)• control lock (page 15)
Resetting all of the adjustment data for all input signalsPress and hold the RESET button for more than two seconds.
NoteThe RESET button does not function when (CONTROL LOCK) is set to ON.
Technical Features
Preset and user modesWhen the monitor receives an input signal, it automatically matches the signal to one of the factory preset modes stored in the monitor’s memory to provide a high quality picture at the center of the screen. (See Appendix for a list of the factory preset modes.) For input signals that do not match one of the factory preset modes, the digital Multiscan technology of this monitor ensures that a clear picture appears on the screen for any timing in the monitor’s frequency range (horizontal: 30 – 121 kHz, vertical: 48 – 160 Hz). If the picture is adjusted, the adjustment data is stored as a user mode and automatically recalled whenever the same input signal is received.
Note for Windows usersFor Windows users, check your video board manual or the utility program which comes with your graphic board and select the highest available refresh rate to maximize monitor performance.
Power saving function
This monitor meets the power-saving guidelines set by VESA,
E
NERGY
S
TAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below.
* “Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency.
** When your computer enters a power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters a power saving mode.
RESET
Power mode Power consumption
1
(power) indicator
normal operation
≤
145 W green
1 standby
≤
100 W green and orange alternate
2 suspend(sleep)*
≤
15 W green and orange alternate
3 active off**(deep sleep)*
Approx. 1 W orange
power off 0 W off
17
US
TroubleshootingBefore contacting technical support, refer to this section.
If thin lines appear on your screen (damper wires)The lines you are experiencing on your screen are normal for the Trinitron monitor and are not a malfunction. These are shadows from the damper wires used to stabilize the aperture grille and are most noticeable when the screen’s background is light (usually white). The aperture grille is the essential element that makes a Trinitron picture tube unique by allowing more light to reach the screen, resulting in a brighter, more detailed picture.
On-screen messagesIf there is something wrong with the input signal, one of the following messages appears on the screen.
If NO INPUT SIGNAL appears on the screen
If OUT OF SCAN RANGE appears on the screen
For more information, see “Trouble symptoms and remedies” on page 18.
1
The selected connector
This message shows the currently selected connector (HD15 or BNC).
2
The input signal conditionNO INPUT SINGAL
This indicates that no signal is input, or that no signal is input from the selected connector.
Damper wires
MON I TOR I S WORK I NGHD1 5 :NO I NPUT S I GNA L
WH I TEREDGREENB LUE
I NFORMAT I ON
1
The selected connector and the frequencies of the current input signal
This message shows the currently selected connector (HD15 or BNC). If the monitor recognizes the frequencies of the current input signal, the horizontal and vertical frequencies are also displayed.
2
The input signal conditionOUT OF SCAN RANGE
This indicates that the input signal is not supported by the monitor’s specifications.
3
The remedies
CHANGE SIGNAL TIMING appears on the screen. If you are replacing an old monitor with this monitor, reconnect the old monitor. Then adjust the computer’s graphic board so that the horizontal frequency is between 30 - 121 kHz, and the vertical frequency is between 48 - 160 Hz.
MON I TOR I S WORK I NGBNC : 1 3 0 . 0 k H z / H57
OUT OF SCAN RANGE
CHANGE S I GNA L T I M I NG
WH I TEREDGREENB LUE
I NFORMAT I ON
z
1-8
18
Trouble symptoms and remediesIf the problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual.Use the self-diagnosis function (page 20) if the following recommendations do not resolve the problem.
Symptom Check these items
No picture
If the 1 (power) indicator is not lit • Check that the power cord is properly connected.• Check that the 1 (power) switch is in the “on” position.
If the NO INPUT SIGNAL message appears on the screen, or if the 1 (power) indicator is either orange or alternating between green and orange
• Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets. If you are using the five BNC connectors, connect them in the correct order (from left to right: Red-Green-Blue-HD-VD) (page 6).
• Check that the INPUT switch setting is correct (page 8).• Check that the HD15 video input connector’s pins are not bent or pushed in.
xProblems caused by the connected computer or other equipment• The computer is in power saving mode. Try pressing any key on the computer keyboard.• Check that the computer’s power is “on.”• Check that the graphic board is completely seated in the proper bus slot.
If the OUT OF SCAN RANGE message appears on the screen
xProblems caused by the connected computer or other equipment• Check that the video frequency range is within that specified for the monitor. If you
replaced an old monitor with this monitor, reconnect the old monitor and adjust the frequency range to the following.Horizontal: 30 – 121 kHzVertical: 48 – 160 Hz
If no message is displayed and the 1 (power) indicator is green or flashing orange
• Use the Self-diagnosis function (page 20).
If using Windows 95/98 • If you replaced an old monitor with this monitor, reconnect the old monitor and do the following. Install the Windows Monitor Information Disk (page 7) and select this monitor (“CPD-G500/G500J”) from among the Sony monitors in the Windows 95/98 monitor selection screen. If you choose to select “Plug and Play,” connect the monitor to the computer with the HD15 video signal cable. You cannot use the five BNC connectors.
If using a Macintosh system • Check that the Macintosh adapter and the video signal cable are properly connected (page 6).
Picture flickers, bounces, oscillates, or is scrambled
• Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors, laser printers, electric fans, fluorescent lighting, or televisions.
• Move the monitor away from power lines or place a magnetic shield near the monitor.• Try plugging the monitor into a different AC outlet, preferably on a different circuit.• Try turning the monitor 90°
to the left or right.
x
Problems caused by the connected computer or other equipment
• Check your graphics board manual for the proper monitor setting.• Confirm that the graphics mode (VESA, Macintosh 21" Color, etc.) and the frequency of
the input signal are supported by this monitor (Appendix). Even if the frequency is within the proper range, some video boards may have a sync pulse that is too narrow for the monitor to sync correctly.
• Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture.
Picture is fuzzy
• Adjust the brightness and contrast (page 10).• Degauss the monitor* (page 15).• If CANCEL MOIRE is ON, the picture may become fuzzy. Decrease the moire
cancellation effect or set CANCEL MOIRE to OFF (page 13).
19
US
* If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard, but this is not a malfunction.
Displaying this monitor’s name, serial number, and date of manufacture.While the monitor is receiving a video signal, press and hold the center of the control button for more than five seconds to display this monitor’s information box.
If the problem persists, call your authorized Sony dealer and give the following information.• Model name: CPD-G500• Serial number• Name and specifications of your computer and graphics board.
Picture is ghosting • Eliminate the use of video cable extensions and/or video switch boxes.• Check that all plugs are firmly seated in their sockets.
Picture is not centered or sized properly
• Perform the (AUTO) function (page 11).• Adjust the size (page 11) or centering (page 11). Note that some video modes do not fill
the screen to the edges.
Edges of the image are curved • Adjust the geometry (page 12).
Wavy or elliptical pattern (moire) is visible
• Set CANCEL MOIRE to ON and adjust the degree of moire cancellation until the moire is at a minimum (page 13).
xProblems caused by the connected computer or other equipment• Change your desktop pattern.
Color is not uniform
• Degauss the monitor* (page 15). If you place equipment that generates a magnetic field, such as a speaker, near the monitor, or if you change the direction the monitor faces, color may lose uniformity.
• Adjust the landing (page 13).
White does not look white
• Adjust the color temperature (page 13).• Check that the five BNC connectors are connected in the correct order (from left to right:
Red-Green-Blue-HD-VD) (page 6).
Letters and lines show red or blue shadows at the edges
• Adjust the convergence (page 12).
Monitor buttons do not operate( appears on the screen)
• If the control lock is set to ON, set it to OFF (page 15).
COLOR RETURN function does not operate
• Before using this function, the monitor must be in normal operation mode (green power indicator on) for at least 30 minutes. For more information on using the IMAGE RESTORATION function, see page 15.
• Adjust the computer’s power saving settings to keep the monitor in normal operation mode for more than 30 minutes.
• The monitor may gradually lose its ability to perform this function due to the natural aging of the picture tube.
A hum is heard right after the power is turned on
• This is the sound of the auto-degauss cycle. When the power is turned on, the monitor is automatically degaussed for two seconds.
Symptom Check these items
EASY EXPERT s BGR
5 0 0 0 K 6 5 0 0 K 9 3 0 K05 0 K00
I MAGERESTORAT I ON
AVA I L AB L EAF TER WARM UP
COLOR
MENU
SER NO : 1234567MODEL : CPD G500
MANUFACTURED : 1999-52
INFORMATION
Example
b
1-9
20
Self-diagnosis functionThis monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer(s), the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard.
If the 1 (power) indicator is green
1 Remove any plugs from the video input 1 and 2 connectors, or turn off the connected computer(s).
2 Press the 1 (power) button twice to turn the monitor off and then on.
3 Move the control button , for 2 seconds before the monitor enters power saving mode.
If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cables and check the condition of your computer(s).
If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition.
If the
1
(power) indicator is flashing orange
Press the
1
(power) button twice to turn the monitor off and then on.
If the
1
(power) indicator lights up green, the monitor is working properly.
If the
1
(power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the
1
(power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board.
Specifications
CRT 0.24 mm aperture grille pitch 21 inches measured diagonally 90-degree deflectionFD Trinitron
Viewable image size Approx. 403.8
×
302.2 mm (w/h) (16
×
12 inches) 19.8" viewing image
ResolutionMaximum Horizontal: 2048 dots
Vertical: 1536 linesRecommended Horizontal: 1600 dots
Vertical: 1200 linesStandard image area Approx. 388
×
291 mm (w/h) (15
3
/
8
×
11
1
/
2
inches) or Approx. 364
×
291 mm (w/h) (14
3
/
8
×
11
1
/
2
inches)Deflection frequency* Horizontal: 30 to 121 kHz
Vertical: 48 to 160 HzAC input voltage/current 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 APower consumption Approx. 145 WDimensions Approx. 497
×
480
×
478 mm (w/h/d) (19
5
/
8
×
19
×
18
7
/
8
inches)Mass Approx. 32 kg (70 lb 9 oz)Plug and Play DDC1/2B/2Bi, GTF**Supplied accessories See page 6
* Recommended horizontal and vertical timing condition• Horizontal sync width duty should be more than 4.8% of total
horizontal time or 0.8 µs, whichever is larger.• Horizontal blanking width should be more than 2.3 µsec.• Vertical blanking width should be more than 450 µsec.
** If the input signal is Generalized Timing Formula (GTF) compliant, the GTF feature of the monitor will automatically provide an optimal image for the screen.
Design and specifications are subject to change without notice.
MENU
RESET INPUT HD15 BNC
1 (power) indicator
MENU
CPD-G500
Top cover
Video shield
5
7
3
2
1
Two claws
2 Two clawsBezel assembly Bezel assembly
Cabinet
Cabinet
Cabinet
Three screws(+ BVTT 4 x 8)
6
Four screws(+ BVTT 4 x 8)
4
Two screws(+ BVTP 4 x 16)
Push in the tip of a screwdriverabout 5mm to unlock the claw.
A
B
Three screws(+ BVTT 4 x 8)
Two screws(+ BVTP 3 x 12)
D board
Screw(+ P 3.5 x 20)
Open the D block in the directionof the arrow . and remove ofthe arrow .
Two hooks
5
A
B
CN504
CN505
GND
1
2
3 4
2-1. CABINET REMOVAL
SECTION 2
DISASSEMBLY
2-2. D BOARD REMOVAL
2-1
CPD-G500
A
B
Three screws(+ BVTT 4 x 8)
Two hooks
Four screws(+BVTP 3 x 8)
G shield
G boardCN602
CN654CN653CN652
CN650
GND
GND
Open the G block in the directionof the arrow . and remove ofthe arrow .
A
BTwo printed circuit board holders
2
1
Two screws(+ BVTP 3 x 8)
7
AC inlet (3P)8
5
3
4
6
A board (2/2)
Four screws(+BVTT 4 x 8)
1
Two screws(HD15)
4
I/O terminal board assembly5
3
A board (1/2)
A board (1/2)
A board (1/2)
Screw lock
2
When installing I/O terminalboard assembly, be sure to applyscrew lock on 2 spots after screws (HD15) are fixed.
2-3. G BOARD REMOVAL
2-4. A BOARD, I/O TERMINAL BOARD ASSEMBLY REMOVAL
2-2
CPD-G500
N board
Printed circuit board holder1
2
CN010CN011
CN001
CN007
CN002
CN5002CN5001
CN5003
D board (Refer to 2-2.)
CN602
Rear shieldD,G boards
G board(Refer to 2-3.) AC inlet (3P)
CAUTION : SHORT
If the claw is hooked,opening and closingthe board is impossible.Do not try to do it by force.
If the claw is hooked,opening and closingthe board is impossible.Do not try to do it by force.
2-5. N BOARD REMOVAL
2-6. SERVICE POSITION
2-3
CPD-G500
CN801
9
10
8
7
6
Open the D block.(Refer to 2-2.)
GND
CN5CN4
A board
Open the G block.(Refer to 2-3.)
Neck assembly
Deflection yoke
Picture tube
Three connectors
Anode cap(See page 2-5.)
1
2
3
4
5
Four screws (Tapping screw 5)
Bezel assembly
4
5
8
6
7
Four screws(Tapping screw 5)
H1 board
Two screws(+ BVTP 4 x 16)
Bezel assembly
2
Before removing the bezel assembly, secure the picture tube by attaching two screws to the picture tube shield at the positions shown with an arrow (diagonal two places) to prevent the picture tube from falling. (Usethe screws +BVTT 4 x 8 that fix top cover.)
1
3
Input selection
CN801
Picture tube shield
Two H printed circuit board brackets
Menu button
2-7. BEZEL ASSEMBLY, H1 BOARD REMOVAL
2-8. PICTURE TUBE REMOVAL
2-4
CPD-G500
c
Anode Button
b
a
CN891
CN601
GND
3
4
5
2
J board
Claw
Two hooks
Remove the picture tube.(Refer to 2-8.)
1
Two screws(+BVTT 4 x 8)
4pin
4pin
2pin
Picture tube shieldcomplete assembly.
2-9. J BOARD REMOVAL
2-5
3 When one side of the rubber cap isseparated from the anode button, theanode-cap can be removed by turningup the rubber cap and pulling up it in thedirection of the arrow c.• HOW TO HANDLE AN ANODE-CAP
1 Don’t scratch the surface of anode-caps with shartp shapedmaterial!
2 Don’t press the rubber hardly not to damage inside of anode-caps!A material fitting called as shatter-hook terminal is built in therubber.
3 Don’t turn the foot of rubber over hardly!The shatter-hook terminal will stick out or damage the rubber.
• REMOVAL OF ANODE-CAPNOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after
removing the anode.
• REMOVING PROCEDURES
1 Turn up one side of the rubber cap inthe direction indicated by the arrow a.
2 Using a thumb pull up the rubber capfirmly in the direction indicated by thearrow b.
CPD-G500
CN801
CN
891
CN5
CN5001
CN601
CN603
CN602
CN5003
CN5002 CN002
CN001
CN509
CN506
CN502
CN505
CN501
CN508
CN4
CN
007
CN
011
CN
010
CN402
CN405
CN407
CN408
CN
403
CN
406
CN
504
FBT
CN651
G boardN board
AC inlet
A board
I/O terminal board assembly
D board
Rear shield
Picture tube
J board H1 board
CN650
CN652
CN653
CN654
4pin
4pin
2-6
2-10. HARNESS LOCATION
CPD-G500
HV RegulatorCircuit Check
HV ProtectorCircuit Check
Beam CurrentProtector CircuitCheck
When replacing or repairing the shown below table, thefollowing operational checks must be performed as a
safety precaution against X-rays emissions from the unit.
SECTION 3
SAFETY RELATED ADJUSTMENT
3-1
Part Replaced ([)
RV901HV ADJ
* Confirm one minute later turning on the power.
a) HV Regulator Circuit Check
1) Enter black crosshatch signal (black on white back-ground), and check that high voltage is in the speci-
fied range.
[Specification]: 27.00 ±0.10 kV2) Check that the voltage of D912 cathode on the D
board is 27.0 V or more.
b) HV Protector Circuit Check
1) Enter black crosshatch signal (black on white back-
ground).
2) Apply the specified voltage to the D912 cathode onthe D board, and check that high voltage is 0.1 kV or
less.
[Specification]: 31.90 +0.00/–0.05 V
c) Beam Current Protector Circuit Check
(1st Protector): D Board
1) Apply 4.5 V DC to CN504 0 pin on the D board,and check high voltage value.
2) Connect constant current source to a section between
T902 (FBT) !¡ pin and !™ pin (GND) on the Dboard, and check that high voltage checked in 1)
lowers by 1.50 kV or more when the specified cur-
rent flows to the !¡ pin.[Specification]: 2.00 +0.00/–0.01 mA
d) Beam Current Protector Circuit Check
(2nd Protector): D Board
1) Connect constant current source to a section between
T902 (FBT) !¡ pin and !™ pin (GND) on the D
board, and check that the voltage of CN504 0 pinbecomes 0 V or less when the specified current flows
to the !¡ pin.
[Specification]: 1.70 +0.00/–0.01 mA
e) Beam Current Protector Circuit Check
: G Board
1) Apply 264 V AC.2) Enter about 5 V to CN650 4 pin on the G board, and
check that the output voltage of CN653 2 pin is
about 15 V.3) Enter about 0±0.2 V to CN654 4 pin, and check that
the output voltage of CN653 2 pin becomes 1.0 V
or less.
f) Beam Current Protector Circuit Check
: N Board
1) Check that the protector operates, when the voltage
of CN010 !§ pin on the N board is lowered to 0 V orless (for more than 2 seconds).
Part Replaced (])
D Board C920, IC901, R923R924, R929, R945,RV901, T902(FBT)• Mounted D Board
D Board C922, C925, C926,D912, D914, D915,D921, Q907, Q908,R921, R922, R932,R937, R939, T902(FBT)• Mounted D Board
D Board C910, C921, C933,D901, D902, D913,IC503, IC901, R901,R920, R928, R930,R931, R940, R941,T902(FBT)• Mounted D Board
G Board IC652• Mounted G Board
N Board IC001, R031, R032• Mounted N Board
CPD-G500SECTION 4
ADJUSTMENTS
• Landing Rough Adjustment1. Enter the full white signal. (or the full black dots signal).2. Adjust the contrast to the maximum.3. Make the screen monogreen.Note: Off the outputs from R ch and B ch of SG.4. Reverse the DY, and adjust coarsely the purity magnet so
that a green raster positions in the center of screen.5. Adjust the tilt of DY, and fix lightly with a clamp.Note: “TILT” = “128”.
• Landing Fine Adjustment1. Put the set inside the Helmholtz coil. (“LCC SW” = “12”)2. Input the single green signal and set the “CONTRAST”=
“255”.Note: After the W/B adjustment with 9300K, measure an aver-
age of ΣIk when a full white signal is entered in the CONTMAX/BRT CENT status. Then make adjustment so thatthe specified screen can be attained after aging for 2 hourswith Ik equivalent to 30% of the average value.
3. Demagnetize the metal part of the chassis with the hand de-gausser and coil degausser, and the CRT surface with thehand degausser.Input AC 230V to AC IN, turn on and off the power to per-form auto degaussing. (Perform auto degaussing by setting“FUNCTION SW”=1. Return to the original value afteruse.)Demagnetize the CRT surface with the hand degausseragain.
Note:(1) Hand degauss must be used on stand-by or power-off condi-
tion.This model has an automatic earth magnetism correctionfunction by using an earth magnetism sensor and a LCC coil.When using a hand degauss while monitor (LCC coil) is be-ing operated, it sometimes gets magnetized, and the systemmay not work properly as a result.
(2) Adjust in a non-magnetic field.(3) If adjusting in a magnetic fields, add the shift from the non-
magnetic field in your estimation.4. Attach the wobbling coil to the designated part of the CRT
neck.5. Attach the sensor of the landing adjustment unit on the CRT
surface.
± 6 ± 6 ± 6
± 6 ± 6 ± 6
± 6 ± 6 ± 6
<Specifications>Adjust so that the green is withinthe specification given right.4 corner adjust target : within ± 1
The red and blue must be withinthe specification given right withrespect to the green.
A difference between red and bluemust be within the specificationgiven right.
0 ± 3 0 ± 7.5 0 ± 3
0 ± 3 0 ± 7.5 0 ± 3
0 ± 3 0 ± 7.5 0 ± 3
(µm)
(µm)
10 10 10
10 7 10
10 10 10
(µm)
* Adjustment and measurement should be made at the pointsone inch inside the fluorescent screen.
7. For the up/down swing, swing the DY and insert a wedge sothat the up and down pins are equal at the top and bottom.Adjust the H.TRP VR of DY so that the horizontal trapezoidis equal at the left and right. Insert the wedge firmly so thatthe DY does not shake.
8. Check the landing of each corner, and if it does not satisfythe specification, adjust the landing of four corners using“LCC LT“, “LCC LB”, “LCC RT” and “LCC RB”.However, the register adjustment must be limited within thefollowing range.
“LCC NS” 128 ± 15“LCC LT”, “LCC LB”, “LCC RT”, “LCC RB”
128 ± 40After adjustment, save the service data.
9. Remove the sensor and wobbling coil.10. Switch the signal to R.G.B., and check that each color is
pure.11. Check that the DY is not tilting, and fix the purity Mg with a
white pen. Fix wedges with RTV.
4-1
6. Adjust the DY position and purity, and the DY tilt, and land-ing of the center and 4 corners with the landing checker.After adjustment, set “LCC SW” to “13”.• Write terrestrial magnetism sensor reading VX and VY to
“LCC VX” and LCC VY” respectively. Adjust the land-ing by moving “LCC NS”, “LCC LT”, “LCC LB”, “LCCRT” and “LCC RB”. However, the register adjustmentmust be limited within the following range.“LCC NS” 128 ± 15“LCC LT”, “LCC LB”, “LCC RT”, “LCC RB”
128 ± 40Save the service data.
Note: Hand degauss must be used on stand-by or power-off condition.This model has an automatic earth magnetism correction function by using an earth magnetism sensorand a LCC coil. When using a hand degauss while monitor (LCC coil) is being operated, it sometimesgets magnetized, and the system may not work properly as a result.
CPD-G500
4-2
Connect the communication cable of the computer to the connector located on the D board. Run the service software and then followthe instruction.
IBM AT Computeras a Jig
1-690-391-211 A-1500-819-AInterface Unit
2
*The parts above ( ) are necessary for DAS adjustment.1 3
D-sub(9 Pin [female])
mini Din(8Pin)
4 Pin
3-702-691-01Connector Attachment
3
To BUS CONNECTOR
4 Pin 4 Pin
• Convergence Rough Adjustment(1) Receive an image of the white crosshatch signals (white
lines on black).(2) Place the protrusions of the 6-fold poles magnet attached to
the CRT neck upon each other.(3) Make rough adjustment of the H and V direction conver-
gence by using 4-fold poles magnet.
• White Balance Adjustment Specification1. 9300K
x=0.283 ± 0.005y=0.298 ± 0.005
(All White)2. 6500K
x=0.313 ± 0.005y=0.329 ± 0.005
(All White)3. 5000K
x=0.346 ± 0.005y=0.359 ± 0.005
(All White)
• Vertical and Horizontal Position and SizeSpecification
• Focus adjustmentAdjust the focus volume 1 and 2 for the optimum focus.
• Convergence Specification
B
a
a 2.0 mmb 2.0 mm
a
b
b
A
MODE
A
B
4 : 3
388
291
5 : 4
364
291
B
AA 0.20 mm
B
60kHz 60kHz>
0.24 mm
0.24 mm
0.28 mm
VfH
* Set so that the protruding parts ofthe 2 magnet rings agree witheach other.
XBVXCV
B
RB
R
RB
BR
R BB R
TLV
TLH
YBHYCH
R BR B
H-TRP YBH
TLH
APH
XCVXBV
YCH
Purity
4-pole magnet
6-pole magnet
2-pole magnet
Focus 1
Focus 2
FBT
5-1 5-2
SECTION 5
DIAGRAMS5-1. BLOCK DIAGRAMS
HD
21
19
18
17
16
20
12
7
6
2
4
13
14
8
9
10
HOST GND 1
DDC SCL 1
DDC +5V 1
VS1
HS/VS1
DDC SDA 1
INPUT SEL
G. SYNC DET
SYNC ON G
CLP
C. BLK
SCL
SDA
H. SYNC
V. SYNC
HFBP
B
A
TO N BOARDCN001
CTO N BOARDCN010
TO N BOARDCN002
16
18
20
24
25
22
23
14
12
10
8
7
6
5
4
3
2
1
STBY+5V
RXD
TXD
+15V
+15V
–15V
–15V
HDF
VDF
ABL
HV DET
S0
H CENT
S6
HSPBAL
HLINBAL
H SIZE
H SHAPE
HDF
VDF
ABL DET
HV DET
S0
H CENT
S6
HSPBAL
HLIN
H SIZE
HSP
5
3
1
35
32
29
23
21
19
26
27
28
11
9
7
BIN2
GIN2
RIN2
ROUT
GOUT
BOUT
41
38
33
12
8
2
2
6
11
ROUT
GOUT
BOUT
14
6
4
ROUT
GOUT
BOUT
RIN
GIN
BIN
RIN
GIN
BIN
R DET IN
G DET IN
B DET IN
D/A4
D/A3
D/A2
CLP
C. BLK
SCL
SDA
BIN1
GIN1
RIN118
14
25
INPUT SW
G. DET
SYNC SEP OUT
2
4
6
BIN2
GIN2
RIN2
CN402
5BNC
R
IC407
CN403
INPUT1(HD15)
CN504
CN401HD15
5
4
3
2
1
1015
914
813
712
611
H DRVQ502, 503
H OUTQ509
H OUT, BUFFQ515, 520
T501HDT
IC404OSD
H CENTQ514
IC501PIN CONTROL
IC503AMP
IC502H CENT OUT
T502HCT
+12V
T503HST
L505HOC
OUT
HFBP
TH DET
VDF
V RET
V SHAPE V+
V–
V–
V+
HDF
S0-4, S6
S5
HV DET
+220V
+220V
+220V
+12V
PIN OUTQ508
H DRVQ701-705
S CAP CHANGEQ501, 506, 507,
510-513, 517, 525
HL OUTQ516, 518
RELAY DRVQ519
V DRVQ706, 707
T701DFT
HV DETQ907, 908
HV DRVQ903, 904
HV OUTQ906
HV REG SWQ905
T901HRC
T902 FBT
HV HV
FC FC
RV901
HV ADJ
FV FV
IC401INPUT SELECT
IC402RGB DRIVE
IC403RGB AMP
4 9 13 1
18 19 20 21 15 16 17
12 11 10
17
6
514
11
12
7
3
5
7
26
25
24
4
3
5
6
7
5
3
1
24
4 5
81
2 5
2 5
2 1
3
39
1
5
14
3
6
7
8
14
13
15
14
13
ROUT
GOUT
BOUT
GND
RCI
GCI
BCI
PWM1
XT1
XT0
H. SYNC
V. SYNC
HFBP
SCL
SDASCL
SDA
VS
Hfly
RIN
GIN
BIN
IC406CUTOFF AMP
X4018MHz
G2 CONTQ406, 407, 410
IC405 (1/2)
+–
PWM
2
PWM
3
PWM
4
BUFFERQ101,Q201,Q301
9
1
2
4
6
8
HEATER
STBY+5V
1W+5V
+80V
+220V
+12V
5V
5V-2
+80V
+220V
+12V
PS401 1A
CN405
G2
1 G2
CN406
5
3
1
7
KR
KG
KB
HEATER+
CN407
5
3
1
7
KR
KG
KB
HEATER+
FV FC HV
CN408V901
PICTURE TUBE
1 G2
CN506
E
TO G BOARDCN652
A (VIDEO AMP, RGB OUT)
D (DEFLECTION)
DTO N BOARDCN011
20
18
16
14
12
10
25
24
23
22
21
19
8
6
3
1
4
STBY+5V
1W+5V
ECO SW
PWR SW
DGUS SW
HTR SW
TH DET
S4
S3
S5
S2
S1
HFBP
HD
V RET
VSHAPE
+12V
TH DET
S4
S3
S5
S2
S1
HFBP
HD
V RET
VSHAPE
CN505
2
3
4
STBY+5V
RXD
TXD
CN503
ECS
2
4
1
6
+15V
–15V
+12V
+80V
CN501
CN508
F
TO G BOARDCN653
1
2
3
4
5
6
STBY+5V
1W+5V
ECO SW
PWR SW
DGUS SW
HTR SW
CN502
+80V
–15V
+15V
+12V
HTO G BOARDCN650
5
4
3
2
1
+220V
+220V
H CENT L
H CENT N
H CENT H
HDIN
PWMOUT
ERRIN
O2
O3HLIN
O4
–4
+1 O1
ABL
ABL
DET
HSP
H S
IZE
S5-1
–3
H SENT H
H SENT L
H SENT N
H SENT H
H C
ENT
HSP
BAL
VCC
VEE
+VIN
–VIN
GTO G BOARDCN654
PIN DRVQ504, 505
GAIN SWQ526
Q523
PIN AMPQ524
TH DETQ521, 522
2
1
6
5
17
14
16
15
11
11
15
14
5 7
112
T505HLC
4 1
23
5
2
14
10
12
3
11
5
4
2
3
5
PWMOUT
+
HVD
HDIN
ERROUT
–
IC901HV CONTROL
ABL
OUT VCC
–
+
OUT
IC701V DY OUT
RY501
V. DY
R. DY
S5
2
3
9
10
5
6
V. DY C
V. DY H
H. DY H
H. DY H
H. DY C
H. DY C
CN509
S5
B-SS3484 <J..> -BD1-EPS05
RIK
GIK
BIK DRIFT CORRECT
Q401
S5-1
INPUT2(BNC)
CONNECTOR PANEL
GBHDVD
OSD
R
OSD
G
OSD
B
OSD
BLK
V-D
ET
25
21
30
22
23
D/A5
CLP
BLK
SCL
SDA
VCC KICKQ402
5V
RO
UT
GO
UT
BOU
T
FBLK AV
17
8
5-3 5-4
4
3
2
6
5
1
20
18
16
10
15
9
8
14
13
12
21
46
47
104
103
29
53
51
108
69
41
42
98
156
152
157
153
149
140
148
131
DDC+5V 1
DDC SCL 1
DDC SDA 1
HS/CS 1
VS 1
HOST GND 1
CLP
C. BLK
SYNC ON G
INPUT SEL
G. SYNC DET
SCL
SDA
H. SYNC
V. SYNC
HFBP
ABL (NC)
UBI1
UBI2
UIN2
UIN1
P52/INT2
UOUT3
UOUT1
UIN5
P91
SCL2
SDA2
UOUT7
UPWM21
UPWM19
UPWM22
UPWM20
UPWM18
UPWM13
UPWM17
UPWM9
83
84
39
38
40
33
34
AIN7
AIN8
SDA1
SCL1
P82
P90
RESET
3
4
76
13
77
19
8
P10/A0
P11/A1
AIN1
P40/D0
AIN2
P46/D6
P15/A5
89
71
128
86
138
126
144
136
133
45
44
AIN12
DAC0
UPWM8
AIN10
UPWM12
UPWM7
UPWM15
UPWM11
UPWM10
TXD
RXD
LED0
LED1
KEYDET
INPUT SW
ENV
59
58
60
56
55
88
15, 94
95
93
92
25
35
34
33
29
27
13
9
5
8
4
PA4
PA3
PA5
PA2
PA1
AIN11
P42/D2, P93
P94
P92
INT1
AFC FIL
BSHPLVL
DVSHAPE
VDC
HPHASE
HFREQ
HPLL
AFC SW
VSH
FBP
VSAWRST
HD DUTY
REG9V
HS
HD
VSHAPE
5
18
124
99
120
117
122
114
111
90
96
67
109
66
P12/A2
P45/D5
UPWM6
UOUT8
UPWM4
UPWM3
UPWM5
UPWM2
UPWM1
AIN13
P95
UOUT5
UIN6
UOUT463
XTB
54
61PA0
PA6
VSP
HD
HSO
UT
ECO
SW
SOG
DET
VSO
SD
HFB
P
64XTD
2
1
4
106
107
31
HS/CS 2
VS 2
HOST GND 2
UIN3
UIN4
P54/INT4
16
12
14
18
20
22
23
24
25
6
8
1
2
3
4
10
19
21
ABL
HDF
VDF
HV DET
H CENT
HSPBAL
HLINBAL
HSIZE
HSHAPE
TXD
RXD
+15V
+15V
–15V
–15V
STBY+5V
S0
S6
2
3
4
5
7
1
12
14
16
23
10
18
20
25
22
6
8
S4
S3
S5
S2
S1
TH DET
PWR SW
DGUS SW
HTR SW
VRET
ECO SW
HFBP
HD
VSHAPE
+12V
STBY+5V
1W+5V
CN002
IC001CPU/DSP
CN001
CN010
Q009
IC006
AIN0
Q010
Q012
Nµ-COM, V.CONV, H. CONV,LCC, GEO MAGNETIC SENSOR
+–
A
B
C
D
CN011
ECO SW
HFBP
HD
VSP
+12V
STBY+5V
1W+5V
+15V
+15V
STBY+5V
SOG DET
D SCL
D SDA
HSOUT
VS OSD
HFBP
HS1
VC1
HS2
VC2
VS1
SDA1
SCL1
DET
1
VCLK
SCL
SDA
VS1
SCL1
SDA1
X00124.756MHz
TO D BOARDCN505
TO D BOARDCN504
TO A BOARDCN403
TO CONNECTORPANEL
7575
6
+12V
7 6 5
6
78
+–
+–
+–
+–
+–
+–
+–
+–
3
4
1
2
7
8
5
6
LCC-LB (+)
LCC-LB (–)
LCC-LT (+)
LCC-LT (–)
LCC-RB (+)
LCC-RB (–)
LCC-RT (+)
LCC-RT (–)
1
2
LCC-NS (+)
LCC-NS (–)
B-SS3484 <J..> -BD2-EPS05
CN5002IC5301 (2/2)
4
32
IC5301 (1/2)
6
78
IC5101 (2/2)
4
32
IC5101 (1/2)
6
78
IC5201 (2/2)
4
32
IC5201 (1/2)
6
78
IC5401 (2/2)
4
32
IC5401 (1/2)
CN5003
I TO H BOARDCN801
LCC-LB
LCC-LT
LCC-RB
LCC-RT
5
6
3
4
1
2
ROTATION (+)
ROTATION (–)
H CONV (+)
H CONV (–)
V CONV (+)
V CONV (–)
CN5001
6
7
1
2
3
4
8
1W+5V
STBY+5V
LED0
LED1
KEY DET
INPUT SW
ENV DRI
LED0
LED1
KEY DET
INPUT SW
ENV
CN007
ROTATION
LCC-NS
H. CONV
V. CONV
1CLR
2CLR
1CK
2CK
HC1
VC1
HC2
VC2
1Q
2Q
P41/D114
GS5001GEOSENSOR
IC003EEP ROM
SWQ008
HD SWQ011
CURRENT MILLERQ001-003
ECO SWQ007
ACTIVE OFF DETQ004-006
IC004ECO DET
IC005ECO DET
IC010H. V. OSC, AFC,
H. DRV, V. SHAPE
+15V
IC002WDT
5
6
7
SDA
SCL
WC
3
8CK
RESET
IC011ROM
1W+5V
STBY+5V
30
15
6
21
14
1
13
5
9
3
11
1
13
5
9
3
11
1CLR
2CLR
1CK
2CK
1Q
2Q
5-5 5-6
1
3
AC L OUT
AC L IN
CN891
1
3
AC L OUT
AC L IN
CN603 TH601
D610RECT
RY602
1
3
AC L
AC N
CN602 F6016.3A T601AC INLET
RY603
1
4
DGC
DGC
CN601
POWER
S891
J (POWER SW)
H1 (USER CONTROL)
G (POWER SUPPLY)
DGC
12
43
L410AFC
T621PRT
T620PIT
PS6502.0A
IC654+12V REG
D652
D650
VCC
DR
AIN
L SE
N
AC S
EN CATHODE
GND
1
8
2
7 3
6
1
2
7
6
3
4
5
8
53
3
3
4 2
1
1
4
2
1
2 5
1
9
3
10
7
4
3
2
1 12
1 3
11
10
9
8
7
6
5
4 1
5
63
VCC SWQ610LED DRV
Q801, 802
LED DRVQ803, 804
T630SRT
REG SWQ621
PROTECTQ670
IC650+220V SHUNT REG 1
2
3
4
5
H CENT H
H CENT N
H CENT L
+220V
+220V
CN654
6
4
1
2
+80V
–15V
+12V
+15V
CN653
4
6
8
9
1
2
+80V
+220V
+12V
HEATER
SYBY+5V
1W+5V
CN652
2
1
3
6
4
5
1W+5V
STBY+5V
ECO SW
HTR SW
PWR SW
DGUS SW
CN650
PROTECTORPOWER SWQ650-654,
667
Q603REG OUTSTART UP
VCC SWQ631-633
HEATER SWQ671
RELAY DRVQ691
IC630REG
REG SWQ630
IC6531W+5V REG
IC652STBY+5V REG
IC651HEATER REG
VCC OUT
CTL
VCC OUT
CTL
VADJ
1
2
2
4
1
4
1
5
2
IN OUT
IN OUT
PH630
IC680
3
4 2
1
PH620
6
7
1
2
4
3
8
1W+5V
STBY+5V
LED0
LED1
INPUT SW
KEY DET
ENV DRI
1W+5V
STBY+5V
STBY+5V
STBY+5V
STBY+5V
S811
S812S801
D801
GR
TH801
ITO N BOARDCN007
GTO D BOARDCN508
F
E
TO D BOARDCN501
TO A BOARDCN405
H
TO D BOARDCN502
FUNCTION KEY
POWERINPUT
HD15BNC
RESETMENU
B-SS3484 <J..> -BD3-EPS05
5-7 5-8
5-2. FRAME SCHEMATIC DIAGRAM
1 2 3 4 5 6
1
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
4
1 2 3 4 5 6 7 8 9 10
11
1 2 3 4 5 6 7 8 9
1
2
3
1
2
3
1
2
3
1
2
3
4
1 2 3 4 5 6 7 8 9
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1 2 3 4 5 6 7 81 2 3 4 5 6
8 7 6 5 4 3 2 1
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
12345678910
11
12
13
14
15
16
17
18
19
20
21
1 2
H
KBKGKRG1G2
GMG4
RCV
HV
2 1
1
2
3
4
5
6
1
1 2
1
2
3
4
5
6
1
2
3
4
5
6
7
1 2 3 4 5 6 7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1 2 3 4 5 6 7 8
CN405
CN406
CN407 CN408
CN506
CN501
CN508
CN502
CN503
CN509
CN507
CN5001
CN650
CN653
CN654
CN601
CN604
CN603
CN602
CN891
CN652
CN801
CN010
CN011
CN401
CN002
CN007
CN403
CN001
CN402
CN504
CN505
CN5002
CN5003
9P
WHT-L
:S-MICRO
2P
WHT
:VH
8P 8P
2P
WHT
:VH
6P
WHT
:S-MICRO
8P
WHT
:S-MICRO
7P
WHT
:S-MICRO
4PWHT
10P:VH
1P
6P
WHT
:S-MICRO
7PWHT
:S-MICRO
6PWHT
:S-MICRO
8PWHT
:S-MICRO
4PWHT:VH
1P
3P
3PWHT:VH
3PWHT:VH
9P
WHT
:S-MICRO
11PWHT-L
:S-MICRO
25PFFC/FPC
25PFFC/FPC
HD15D-SUB
8P
WHT
:S-MICRO
9P
WHT
:S-MICRO
21P
L-FPC
21P
:FFC
6PWHT
:S-MICRO
25P:FFC
25P:FFC
8P
YEL
:S-MICRO
2P
WHT
:S-MICRO
FASTEN
V.DY
H.DY
CONNECTOR PANEL
FV
FC
HV
ECS
FV
FC
G2
GND
G2
GND
LCC-LT
LCC-LB
LCC-RT
LCC-RB
LCC-NS
H.CONV
V.CONV
CRTSHIELD
DGC
+220V
N.C
+80V
GND
+12V
STBY+5V
HEATER
CLP
GND
C.BLK
GND
ABL(NC)
G2
N.C
KB
GND
KG
GND
KR
GND
HEATER+
GND
KB
GND
KG
GND
KR
GND
HEATER+
GND
STBY+5V
GND
LED0
LED1
B IN 2
G GND 2
G IN 2
R GND 2
R IN 2
GND
GND
B GND 2
ROTATION
-15V
GND
GND
GND
N.C
+220V
+220V
HTR SW
+80V
+15V
+12V
GND
STBY+5V
1W+5V
ECO SW
PWR SW
DGUS SW
STBY+5V
RXD
TXD
GND
GND
H.DY H
H.DY H
H.DY C
H.DY C
NC
NC
V.DY H
V.DY C
GND
NC
GND
CHASSIS GND
N.C
G2
1W+5V
GND
STBY+5V
N.C
AC L
AC N
PWR SW
DGUS SW
HTR SW
DGC
N.C
N.C
DGC
H CENT H
+220V
+220V
N.C
GND
GND
H CENT N
H CENT L
GND
+15V
GND
GND
+12V
-15V
+80V
+220V
N.C
+80V
GND
+12V
HEATER
STBY+5V
AC L OUT
N.C
AC L IN
AC L OUT
N.C
AC L IN
LED0
LED1
GND
GND
STBY+5V
1W+5V
HOST GND 2(NC)
NC
NC
NC
HS/CS2
VS2
GND(NC)
GND
GND
1W+5V
GND
SCL
SDA
V.SYNC
H.SYNC
12
34
5
67
89
10
11
12
13
14
15
LCC-LT(+)
LCC-LT(-)
LCC-LB(+)
LCC-LB(-)
LCC-RT(+)
LCC-RT(-)
LCC-RB(+)
LCC-RB(-)
LCC-NS(+)
LCC-NS(-)
V CONV(+)
V CONV(-)
H CONV(+)
H CONV(-)
ROTATION(+)
ROTATION(-)
+15V
+15V
-15V
-15V
GND
HV DET
ABL
TH DET
GND
HSHAPE
HSIZE
TXD
RXD
GND
GND
HDF
VDF
GND
GND
HCENT
STBY+5V
1W+5V
GND
GND
GND
GND
S0
S1
S2
S3
S4
S5
S6
GND
PWR SW
DGUS SW
HTR SW
GND
HFBP
HD
GND
VSHAPE
GND
VRET
GND
ECO_SW
STBY+5V
HLINBAL
HSPBAL
TH DET
1W+5V
GND
GND
GND
S1
S2
S3
S4
S5
GND
PWR SW
DGUS SW
HTR SW
GND
HFBP
HD
GND
VSHAPE
GND
VRET
GND
ECO_SW
STBY+5V
+15V
+15V
-15V
-15V
GND
HV DET
ABL
GND
HSHAPE
HSIZE
TXD
RXD
GND
GND
HDF
VDF
GND
GND
HCENT
STBY+5V
GND
S0
S6
HLINBAL
HSPBAL
N.C
HS/CS 1
VS 1
GND
DDC+5V 1
DDCSCL 1
DDCSDA 1
HOSTGND 1
N.C
ECO SWCLP
GND
C.BLK
GND
ABL(NC)
GND
SCL
SDA
V.SYNC
H.SYNC
HS/CS 1
VS 1
GND
DDC+5V 1
DDCSCL 1
DDCSDA 1
HOSTGND 1
INPUT_SEL
SYNC_ON_G
G.SYNC_DET
HFBP
CONNECTOR PANEL GND
INPUT_SEL
SYNC_ON_G
G.SYNC_DET
INPUT_SW
KEY_DET
ENV_DRI
KEY_DET
INPUT_SW
ENV_DRI
HFBP
PICTURETUBE
C BLOCK(CRT SOCKET)
A
D(DEFLECTION)
H CENT H
H CENT N
H CENT L
POWER
J(POWER SW)
G
VIDEO AMP,RGB OUT
INPUT1(HD15)
INPUT2(BNC)
1W+5V
1W+5V
POWERSUPPLY
(USER CONTROL)H1
NV.CONV,H.CONV,LCC,GEO MAGNETIC SENSOR
+12V
µ-COM,
FBT
+12V
B-SS3484<J..>-KESSENZU-EPS05
VD HD B G R
5BNC
5-9 5-10
Note:• All capacitors are in µF unless otherwise noted. (pF: µµF)
Capacitors without voltage indication are all 50 V.• Indication of resistance, which does not have one for rating
electrical power, is as follows.
Pitch: 5 mmRating electrical power 1/4 W (CHIP : 1/10 W)
• All resistors are in ohms.• f : nonflammable resistor.• Ï : fusible resistor.• ¢ : internal component.• p : panel designation, and adjustment for repair.• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.• e : earth-ground.• E : earth-chassis.• The components identified by [ in this basic schematic diagram
have been carefully factory-selected for each set in order tosatisfy regulations regarding X-ray radiation.Should replacement be required, replace only with the valueoriginally used.
• When replacing components identified by ] , make thenecessary adjustments indicated. (See page 3-1)
• When replacing the part in below table, be sure to perform therelated adjustment.
5-3. CIRCUIT BOARDS LOCATION 5-4. SCHEMATIC DIAGRAMS AND PRINTEDWIRING BOARDS
• Divided circuit diagram
One sheet of N board circuit diagram is divided into three sheets,
each having the code N-a to N-c. For example, the destination
ab1 on the code N-a sheet is connected to ab1 on the N-b sheet.
a b 1
Ref. No.
Circuit diagram division code
• All voltages are in V.• Readings are taken with a 10 M digital multimeter.• Readings are taken with a color-bar signal input.• Voltage variations may be noted due to normal production
tolerances.• * : Can not be measured.• Circled numbers are waveform references.• s : B + bus.• S : B – bus.
Note: The components identified by shading andmark ! are critical for safety. Replace onlywith part number specified.
Note: Les composants identifiés par un tramé etune marque ! sont critiques pour lasécurité. Ne les remplacer que par une pièceportant le numéro spécifié.
Part Replaced ([)
RV901HV ADJ
Part Replaced (])
D Board C920, IC901, R923R924, R929, R945,RV901, T902(FBT)• Mounted D Board
D Board C922, C925, C926,D912, D914, D915,D921, Q907, Q908,R921, R922, R932,R937, R939, T902(FBT)• Mounted D Board
D Board C910, C921, C933,D901, D902, D913, IC503, IC901, R901,R920, R928, R930,R931, R940, R941, T902(FBT)• Mounted D Board
G Board IC652• Mounted G Board
N Board IC001, R031, R032• Mounted N Board
HV RegulatorCircuit Check
HV ProtectorCircuit Check
Beam CurrentProtector CircuitCheck
G
D
S
2
3
4
5
6
7
8
9
0
!¡
!™
!¢
!§
–
1
G
D
S
G
S S
D
G
D
Ver.1.5
Transistor(FET)
Transistor
Transistor
Discrete semiconductot
(Chip semiconductors that are not actually used are included.)
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Source
Source
Anode Anode
(NC)
(NC)
Cathode
AnodeCathode
Common
Cathode Cathode
Common
Cathode Cathode
Common
Common
Common
Common
Cathode
Anode
Base Emitter
Collector
Base Emitter
Collector
Drain
Gate
Gate
Drain
Device Printed symbol Terminal name Circuit
Terminal name of semiconductors in silk screenprinted circuit ( )
Anode
Anode
Anode Cathode
Anode Anode
Cathode
!£
Transistor(FET)
Transistor(FET)
!∞
EmitterCollectorBase
Transistor
Source
GateDrain
Cathode
AnodeAnode
CathodeAnodeAnode
*D
A
G
J
N
H1
5-11 5-12
(1) Schematic Diagram of A Board
Schematic diagram
AAAAA board l
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
0
2.7
0
2.6
0
0
2.9
0.1
4.9
4.9
2.8
0.7
4.4
2.6
2.0
4.6
2.6
2.72.4
2.5
2.6
2.4
2.5
4.3
3.4
4.5 2.7
2.6
2.7
0.6
0.6
0.5
1 2 4 3 5 6
2.6
2.7
58.1
65.5
2.7
2.6
2.7
2.7
79.0
+220V
5.8
5.8
105
103
109
107
103
101
1.2
1.2
1.2
1.7
0.5
5.8
+80V
11.811.9
2.6
2.7
2.7
3.8
534
4.3
4.3
4.9
4.3
522
82.6
95.6
104
4.7
9
87
4.9
4.3
4.9
4.3
2.72.6
4.9
4.9
0.5
0.3
0.7
3.4
2.3
3.5
0
0
0
0
4.3
4.3
4.3
+5V
+5V
4.3
4.9
10
1
2
3
4
5
6
12
34
56
78
910
1112
1314
1516
1718 19
2021
2223
2425
2627
2829
3031
3233
3435
36
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
12
34
56
78
910
1112
1314 15
1617
1819
2021
2223
2425
2627
28
1 4 6 7 10 11 13 14 15 16 173 85 12
1
345
678
91011
13
GND
1
2
1
2
3
4
5
6
7
8
91
23
45
67
89
1011
1213
1415
1617
1819
2021 22
2324
2526
2728
2930
3132
3334
3536
3738
3940
4142
1
2
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
12
34
56
7 89
1011
1213
14
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
R418
SG402
CN406
C457
D201
C201
C203
D202
C204
R205
R206
R454
C202
C459
R459
R464
L402
C419
R463
C207
C411
C112
C212
C312
CN405
R421
R422
R450
R430
C433
C435
C440
C444
C456
C458
C462
R214
R314
R114
C437
PS401
C101
R105
D101
C302
C301
R305
D301
C307
C107
D302
R306
C303
C304
D102
R106C103
C104
C442
C434
C102
R438
R411
C206
C416
C402
C408
C413
C404 C407
C403
C401
R402
R414
R202
R457
R101
R201
R301
R103
R203
R303
R428
R436
C432
C423
R413
R417
R419
R138
R238
R338
R415
R426
C467
C114
C214
C314
R420
R444
R445
R456
R447
R448
R113
R213
R313
D105
D205
D305
R321 R320
R221 R220
R121 R120
R137
R237
R337
C425
R449
R453
R442
C410
R409
R460
C436
D405
D107
D206
D207
D306
D307
D106
CN403
C205
C216C443
C421
C463
C464
R455
R130
R230
R330
R222
R322
C406
R122
C108
C308
D103
D203
D303
C446
L404
R458
C424
C417
SG101SG201
SG301
SG401
CN401
X401
C113
C213
C313
L403
L405
FB402
FB403
FB404
FB405
FB406
FB411
R119
R219
R319
R310
R210
R110
C438
R424
R425
R427
R431
C405
SK401
C430
C441
R451
R404
R405
R118
R218
R318
R107
R207
R307
C420
R403
D406
CN407 CN408
C115
C215
C315
C120 C220 C320
R109
R209
R309
R117
R217
R317
R128
R228
R328
CN402
IC401
IC407
IC402
C422
R488
R491
IC403
R116
R112
C109
C110
FB302
R211
FB202
C209
C309
C210
R316
C310 R312
IC406
Q401
FB102
R115
R215
R315
Q410
Q407
IC405(2/2)
IC405(1/2)D403
Q406Q301
Q101
Q201
C208
C415
IC404
C431
R212R216
R446
R443
0.01B:CHIP
2PWHT:VH
220k1/2W
1PS226-1150.01B:CHIP
0.01B:CHIP
1PS226-115
4725V
47:CHIP
47:CHIP
2.2M:CHIP
4725V
22100V
10M:RN
2.2k:CHIP
1000p500VB
100k:CHIP
0.125V
B:CHIP
4725V
4.7k:CHIP
100:CHIP
1000p500VB
0.01B:CHIP
B:CHIP
1000p500VB
0.125V
B:CHIP
0.1:CHIP
0.1:CHIP
22:CHIP
22:CHIP
22:CHIP
1A
0.01B:CHIP
47:CHIP
1PS226-115
4725V
0.01B:CHIP
47:CHIP
1PS226-115
0.125V
B:CHIP
0.125V
B:CHIP
1PS226-115
47:CHIP
0.01B:CHIP
4725V
1PS226-115
47:CHIP
0.01B:CHIP
4725V
0.2216V
0.2216V
0.2216V
B:CHIP
B:CHIP
B:CHIP
22016V
16V
0.01B:CHIP
9PWHT-L
:S-MICRO
100:CHIP
100:CHIP
1000p500VB
0.01B:CHIP
:CHIP
4725V
2.2
110V
B:CHIP
4725V
220pCH:CHIP
220pCH:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
4.7k:CHIP
4.7k:CHIP
10
1k:CHIP
47k
100k:CHIP
10M:RN
22µH
75:RN
75:RN
75:RN
75:RN
75:RN
75:RN
100 :CHIP
100k :CHIP
4725V
0.22 16VB:CHIP
1M:CHIP
220:CHIP
2.2k:CHIP
47:CHIP
47:CHIP
47:CHIP
100 :CHIP
47:CHIP
47:CHIP
47:CHIP
470k:CHIP
470k:CHIP
470k:CHIP
470k:CHIP
470k:CHIP
470k:CHIP
22k:CHIP
10k:CHIP
1k:CHIP
0.125V
B:CHIP
0.125V
B:CHIP
0.125V
B:CHIP
1250V
HSS83TD
HSS83TD
HSS83TD
470
470
470
100k:CHIP
220k:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
100pCH:CHIP
0.22
0.01B:CHIP
21PL-FPC
1SS119
2.2M:CHIP
100 :CHIP
100 :CHIP
47 :CHIP
47 :CHIP
100 :CHIP
10k:CHIP
100k:CHIP
470k:CHIP
470k:CHIP
470k:CHIP
22k:CHIP
22k:CHIP
0.01B:CHIP
22k:CHIP
0.125V
B:CHIP
0.125V
B:CHIP
4725V
1PS181-115
1PS181-115
1PS181-115
100µH
2.2M1W:RN
1000p500VB
4700p2kVB
0.2216V
B:CHIP
0.2216V
B:CHIP
0.2216V
B:CHIP
100µH
8MHz
22µH
1.1µH
1.1µH
1.1µH
1.1µH
1.1µH
1.1µH
15k :CHIP
15k :CHIP
15k :CHIP
100k :CHIP
100k :CHIP
100k :CHIP
R161470:CHIP
R261470:CHIP
R361470:CHIP
R439470:CHIP
0.1B:CHIP
1k :CHIP
1k:CHIP
1k :CHIP
470k:CHIP
0.125V
B:CHIP
0.01 B:CHIP
680:CHIP
680:CHIP
680:CHIP
22k :CHIP
0.2216V
B:CHIP
1M:CHIP
1M:CHIP
1M:CHIP
2.2k:CHIP
1k:CHIP
8P 8P
0.01B:CHIP
HSU83TRF
HSU83TRF
HSU83TRF
HSU83TRF
HSU83TRF
HSU83TRF
1PS226-115
12k:CHIP
12k:CHIP
12k:CHIP
1M:CHIP
1M:CHIP
1M:CHIP
4.7k:CHIP
4.7k:CHIP
4.7k:CHIP
0.1250V
0.1250V
0.1250V
0.1250V
0.1250V
0.1250V
HD15D-SUB
2.2M:CHIP
6PWHT
:S-MICRO
M52757FP-TPINPUT SELECT
SN74HC04ANSRG SYNC BUFFER
M52749FP-TPRGB DRIVE
0.2216V
B:CHIP
R407470k:RN-CP
12V
47k:CHIP
4.7k:CHIP
FA4301RGB AMP
4.7k:CHIP
22:CHIP
12pCH:CHIP
0.001CH:CHIP
220:CHIP
10pCH:CHIP
10pCH:CHIP
0.001CH:CHIP
4.7k:CHIP
0.001CH:CHIP
22:CHIP
H8D2972CUT OFF AMP
2SC2412KDRIFT CORRECT
471/2W:SURGE
471/2W:SURGE
471/2W:SURGE
2SC5022-02G2 CONT
DTA114TUAG2 CONT
NJM2904M(TE2)G2 CONT
NJM2904M(TE2)G2 CONT MTZJ-T-77-39B
2SB709AG2 CONT2SC2412K
BUFFER
2SC2412KBUFFER
2SC2412KBUFFER
0.125V
B:CHIP
16V0.22B:CHIP
CXD9514MOSD
1000pB:CHIP
22:CHIP4.7k
:CHIP
100 :CHIP
100 :CHIP
G
G
+12V
G2
+80V
B_CUTOFF
G_CUTOFF
R_CUTOFF
1.5KV
R
B
R
B
+220V
+220V
G2
R_BKG
G_BKG
B_BKG
R_IK
G_IK
B_IK
12V
12V
12V
12V
12V
5V
5V
5V
12V
12V
5V-2
5V
5V-2
5V
5V
5V-2
12V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5V
5
4
3
2
1
10
9
8
7
6
15
14
13
12
11
1
7
2
3
6
5
8
4
C426100p
CH:CHIP
C42722p
CH:CHIP
KB
GND
KG
GND
KR
GND
HEATER +
(G2)
(G2)
(GND) (GND)
GND
GND
B_IN
B_E.P
B_OUT
GND
G_OUT
G_E.P.
G_IN
VBB
GND
VBB
R_IN
R_E.P.
R_OUT
VCC
KB
GND
KG
GND
KR
GND
HEATER +
FV
IMR
FC
GND GND
OSD_BLK
R_IN
VCC1(R)
OSD_R
GND1(R)
G_IN
SOG_IN
VCC1(G)
OSD_G
GND1(B)
ABL_IN
NC
VCC_5V
SOG_OUT
VCC2
R_OUT
GND2
G_OUT
B_OUT
BLK
D/A_1
D/A_2
D/A_3
D/A_4
G_IN2
R_IN2
NC
B_IN2
R_IN1
GND
G_IN1
GND
B_IN1
VCC1
V_DET
VCC2
R_OUT
VCC2
G_OUT
GND
VCC2
B_OUT
GND
G_BUF.OUT
G_BUF.IN
SYNC_SEP.OUT
VCC2
R_DET_IN
G_DET_IN
B_DET_IN
SDA
SCL
GND
V.SYNC
H.SYNC
CONT_DAC
CONT_REF
HOLD_CR1
HOLD_CR2
G.DET
V_DET_C
INPUT_SW
CLP
C.BLK
SYNC_ON_G
ABL(NC)
GND
GND
G.SYNC_DET
R IN 2
G IN 2
R GND 2
G GND 2
B IN 2
B GND 2
HS/CS 1
VS 1
GND
DDC+5V 1
DDCSCL 1
DDCSDA 1
HOSTGND 1
+80V
GND
NC
+12V
+220V
G2
G2(NC)
STBY +5V
HEATER
GND
NC
GND
GND
Main_Brightness
VBB
B-IN
GND1(G)
VCC1(B)
OSD_B
NC
VCC2
VCC2
VCC2
VCC2
NC
CLP SCL
SDA
GND
D/A_5
INPUT_SEL
OSCREF
ADCREF
RCI
GCI
BCI
AVDD
OVDD
BOUT
GOUT
ROUT
PWM4
PWM3
PWM2PWM1
PWM0
XT0
XT1
DVSS
DVDD
AV
VS
HS
SCL
SDA
AGND
Filter
Hfly
FBLK
HFBP
+B
R_OUT
R_BASE
B_IK
B_IN
VBB
GND
G_OUT
G_BASE
B_OUT
B_BASE
G_IK
R_IK
G_IN
R_IN
A1
Y1
A2
Y2
A3
Y3
GND
VDD
A6
Y6
A5
Y5
A4
Y4
FC
G1
G2
KBKG KR
G1
H2
H1
G1
FVTO CONNECTOR
PANEL
INPUT2
INPUT1(HD15)
TO D BOARD
1W+5V
CN652
TO G BOARD
TO D BOARD
CN506
A(VIDEO AMP,RGB OUT)
CN001
C BLOCK
TO N-a BOARD
B-SS3484<J..>-A..-P1-EPS05
R111470:CHIP
R311220:CHIP
S
D402
R406
R490
R491
Q402
R412
D407
C4491
B:CHIP
C4500.47B:CHIP
4.7k:CHIP
MA151WK-TX
100k:CHIP
4.7k:CHIP
2SJ360-TE12LVCC KICK
220k:CHIP
R4411M
:CHIP
1PS226-115
5V
5V
5-13 5-14
• A BOARD IC401 M52757FP
1 2 3
4 6
7
5
8 9
• A BOARD WAVEFORMS
4.6 Vp-p (H)
66.0 Vp-p (H)
64.0 Vp-p (H)
65.0 Vp-p (H)
4.8 Vp-p (H)
64.0 Vp-p (H)
4.7 Vp-p (H)
64.0 Vp-p (H)
64.0 Vp-p (H)
• A BOARD IC402 M52749FP
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
SyncSepa
OR
G D
ET
Inpu
t1 (
R)
Vcc
1 (R
)
Inpu
t1 (
G)
Vcc
1 (G
)
Inpu
t1 (
B)
Vcc
1 (B
)
Inpu
t2 (
R)
GN
D1
Inpu
t2 (
G)
GN
D5
Inpu
t2 (
B)
Syn
c D
ET
1
Syn
c D
ET
2
S-D
ET
out
Vcc
5
Vid
eo D
ET-
Hol
d
V-D
ET
out
SW
ITC
H
Vcc
2 (R
)
OU
TP
UT
(R
)
GN
D2
(R)
Vcc
2 (G
)
OU
TP
UT
(G
)
GN
D2
(G)
Vcc
2 (B
)
OU
TP
UT
(B
)
GN
D2
(B)
G B
uffe
r ou
t
Syn
c S
EP
in
Syn
c S
EP
out
Vcc
3
V-D
ET
in3
GN
D4
V-D
ET
in2
Vcc
4
V-D
ET
in1
R G B
G
2
4
CLAMPSUB
CONTRASTMAIN
CONTRAST OSD MIX AMP
CLAMPF/B
RETRACEBLANKING 41
303442
6
9
5
3
CLAMPSUB
CONTRASTMAIN
CONTRAST OSD MIX AMP
CLAMPF/B
RETRACEBLANKING 38
11
13
10
8
17
16
21 25 26 27 28 29 32 36 3914 1
12
20
7
CLAMPSUB
CONTRASTMAIN
CONTRAST OSD MIX
DACBUSI/F
AMP
CLAMPF/B
OSDLEVEL
4bitMain
CONTRAST8bit
B SUB CONT 8bit
G SUB CONT 8bit
R SUB CONT 8bit
RETRACEBLANKING 33
35
31
24
22
23
19
Sync OnGreenSep
OS
D B
LK IN
INPUT (R)
VCC1 (R)
OSD IN (R)
GND1 (R)
INPUT (G)
INPUT (SOG)
VCC1 (G)
OSD IN (G)
GND1 (G)
INPUT (B)
VCC1 (B)
OSD IN (B)
GN
D
GND1 (B)
ABL INVCC=5V
SOG Sep OUT
Cla
mp
Pul
se IN
VC
C2
OUTPUT (R)
GN
D2
OUTPUT (G)
GN
D
Contrast ref.
Mai
n B
right
ness
OUTPUT (B)
GN
D
Contrast cont.
Ret
race
BLK
IN
D/A
OU
T1
D/A
OU
T2
D/A
OU
T3
D/A
OU
T4
D/A
OU
T5
GND (5V)
SDA
SCL
H
KBKGKRG1G2
GMG4
RCV
HV
CONNECTOR PANEL
INPUT2(BNC)
CN402
TO A BOARD
TO N BOARD
CN002
PICTURETUBE
V901
21TKC
TO D BOARD
T902(FBT)HV
B-SS3484<J..>-A..-P2-EPS05
VD HD B G R
5BNC
0
2.2 Vp-p (8MHz)
IC
IC401 B-3IC402 B-2IC403 A-2 A-2IC404 C-3IC405 D-2IC406 A-3 A-1IC407 D-2
TRANSISTOR
*Q101 C-1 1
Q201 C-1 1Q301 C-1 1
Q401 A-3 1
Q402 D-3 !∞Q406 D-3 1
Q407 D-2 2
Q410 D-3 D-1 ––
DIODE
*D101 B-1 6
D102 A-3 7
D103 A-1 !¡D105 B-3 B-1 –D106 A-2 3
D107 A-2 3D201 B-1 6
D202 A-3 7
D203 A-1 !¡D205 B-3 A-1 –D206 A-1 3
D207 A-2 3D301 B-1 6
D302 A-1 6
D303 A-1 !¡D305 A-3 A-1 –D306 A-1 3
D307 A-3 3D402 D-3 9
D403 A-2 A-2 –D405 D-3 D-1 –D406 D-2 6
D407 D-2 6
CRYSTAL
X401 C-2 C-2
5-15 5-16
Schematic diagram
Ò AAAAA board
— A BOARD (Component Side) —— A BOARD (Conductor Side) —
A VIDEO AMPRGB OUT
• A BOARDSEMICONDUCTORLOCATION
Component( )Side
* : Refer to Terminal name ofsemiconductors in silk screenprinted circuit (see page 5-10)
Conductor( )Side
NOTE:The circuit indicated as left contains high voltage of over600 Vp-p. Care must be paid to prevent an electric shock ininspection or repairing.
A
B
C
D
1 2 3
A
B
C
D
1 2 3
Component( )SideConductor( )Side
Component( )SideConductor( )Side
Component( )SideConductor( )Side
(2) Schematic Diagrams of H1, J Boards
5-17 5-18
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
J
— H1 BOARD —
— J BOARD —
H1 USER CONTROL J POWER SW
STBY+5V
1W+5V
4.9
2.2 4.9
0.2
4.4
3.70
0.1
1
2
3
4
5
6
7
8
9
10
11
G R
TH801
D801
R811
R812
R801
R814
C806
CN801
S811
S801
S812
G
R821
R815
R822
R823R824
R813
C802
Q803
Q804
Q801
Q802
100k
4716V
SPR-325MVW
1k
10k
10k
10K
11PWHT-L
:S-MICRO
22k
4716V
10k:RN
150 470
1k1.5k:RN
:RN
:RN:RN
2SA1309ALED DRIVE
2SA1309ALED DRIVE
2SC3311ALED DRIVE
2SC3311ALED DRIVE
LED0
LED1
KEY_DET
STBY+5V
GND
GND
GND
GND
1W+5V
BNC
HD15
RESET
INPUT
MENU
POWER
INPUT_SW
ENV_DRI
H1(USER CONTROL)
TO N-a BOARD
CN007
CRT SHIELD
TO
B-SS3484<J..>-H1.-EPS05
R802R803R804470220220
R851470
R853100
R852100
1
2
3
CN891
S891
3PWHT:VH
AC L OUT
NCAC L IN
POWER
J(POWER SW)
TO G BOARD
CN603
B-SS9116<NH.>-J..
(3) Schematic Diagram of D Board
5-19 5-20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
A
B
C
D
E
F
G
H
I
Schematic diagrams
Ò H1 JJJJJ boards
Schematic diagram
DDDDD board l
+15V
+15V
-15V
+12V
-15V
+80V
+15V
+15V
+220V
+15V
9.0
8.9
3.5
2.0
2.5
2.5
9.0
3.10
3.2
9.1
9.3
+90V82.5 82.0
82.5 75.5
78.4
4.5
5.0
528
-0.9
0.1
0.7
5.0
4.4
7.7
7.7
00
2.5
-7.6
1.1
1.8
1.80 0
1.10.5
+15V
3.3
2.5
2.5
6.8
9.4
2.5
9.0
2.0
9.0
9.0
3.6
+12V
14.70
27.4
00
28.1
0
28.4
04.84.804.84.8
0
28.50
1.10.6
1.2
4.3
4.3
-14.4
1.8
161
218
9.1
9.0
147
217
192
8.9
8.3
8.2
14.7
14.70
29.6
29.5
28.9
29.3
29.9
31.4
2.5
1.8
198.1
1.7
1.11.1
-0.1 1.8
13.9 -13.41.8
1
2
3
5
4
6
1
2
3
4
5
6
7
1
2
3
4
52
4
5 6
101
9
1 8
4 5
3
2
1
2
3
4
5
6
7
8
9
10
S
1
2
3
4
5
6
1
2
3
4
1
2
3
4
5
6
7
1 2 3 4 5 6 7 8 9 10
11121314151617181920
1 2 3 4 5 6 7 8 9
101112131415161718
1
2
4
5 6
8
10
3
4
13
HV
7
8
9
10
17
11
6
5
12
1
2
16
18
14
15
FV
FC
SSSSSSS
2
3
4
5
7
9
10
11
12
S
S
1 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
12345678
1
2
4
3
S
1234567
8 9 10 11 12 13 14
2
1
3
4
5
R725 R726
R728R724
R723
C710
C708
R727
C712 C713
C709C707R721R720
R560
C539
C533
C534
R549
R550
R574 C552
C549
C540
C532
R557
C546
C547
R570
R576
R567
C510L501
R525
FB501
FB502
D507
R546
C506
C507
R529 R532
C522
C520C518
C523
R544
R538R530
R524
R542 R548C517 C519 C526C530 R552 C535
R551
R526
R531 R539
R545
R722
R553
CN509
R513
C505R514R507
R504
R505 R515
C702
R702
C920
C924
SG901 C923
SG903
D912
C922
C921
R923
SG902
R928
C913
L901
R911
R916
R563
R565 R573
R583
R584
R585
R588
D517
C524
R535
R534
C527
C515
R918
L902
C536
R904 R906
R719
R718
CN501
CN503
C704R516
C559
CN502
C928C929 C935
C927
C901
C908
C932
R561
R555
C545
C554
C548
R533
R522 R537 R558
R729
C711 TH501
R506
TH502
R707
R706
R705
R701
R924
R935R925R919
R927
R922
R932
R930
R931
R926
C915
R908
C542
L503
C560
C529
C516
C558
C918
C919
R939
C926
C925
C706
R929 RV901
C909
R943
C902
R902
R903
R901
C910
R907
C931
R945
R912
R501
R1501
R1502
C502
C508
D511
D513
D514
D516
D701
D702
D703
D901
D910
D918 D919
D921
R547
FB5071.1µH
D922
R503
R512
D509
D506
R708
T505
R915
R509
R519
T902
R578
R579
L505
D508
D920
D707
D510
D505
D907
D909
D915
D515
R580
R582
C501
R937
R933
R934
C503
C903
R732
C930
C571
R510
C543
C537
CN504
CN505
R920
D913
C933
R940
C917
R523
C513
R569
R568
R554
R562 R564
C511
L504
R566
D512
D519
D708
R1506 R1507
C557
C531
C556
C544C528C509 C521
R572
C701
T502
R709 R711 R713
R714
R715
R710
R716
R717
C703
C720
D709
D710
R556 R586 R595
R536
R517
R541 R518
C5620.047B:CHIP
C5680.1
B:CHIP
R597
D522
R593
R591
C565
R598
C561
R917
R508
R590
R502
R599
R589
FB503
FB504
T503
C538
R587
C916
C907
D905
C905
C572
T501
T701
R703
R704
C715
R730
R731
C914 C912
C514 C573
L502
R540
R594
C541
R1503 R1504
R543
R1505
R527
C551
C525
R528 R521
C555
R577R581
C512
C574
C575
FB505
R914
R520D917
D904
D520
D504
R571
C550
Q519
Q517Q513Q512Q511Q510Q507 Q525Q501 Q506
Q521 Q522
IC501
Q526
Q516
Q518
IC503
Q524
Q520
Q514
IC502
Q508
Q504
Q505
Q502
Q503
CN508CN506
D908
IC901
Q903
Q904
Q906
Q907
Q908Q702
Q704
Q705
Q703
Q701
Q706
Q707
IC701
D902
Q515
Q509L903
D923
RY501
1.81/2W:RN
1.81/2W:RN
2201W:RS
2.2k:RN-CP
3.3k:RN-CP
22035V:HT
100025V
25V
1:FPRD
0.22100V:PT
100025V
0.01B:CHIP0.1
:PT10k:CHIP
10k:CHIP
10k:RN-CP
4700pB:CHIP
22025V:HT
22025V:HT
0.471/2W:FPRD
0.471/2W:FPRD
100k:CHIP
0.01B:CHIP
0.1:PT
0.001200V:PT
0.001B:CHIP
C5631500p:PT
271W:RS
1500p630V:PP
2.2k1/2W:FPRD
1k1W:RS
1001/2W:RN
33250V
4.7k:CHIP
1.1µH
1.1µH
YG911S3R
0.223W:RS
0.47:MPS
0.22:MPS
2.2k:CHIP
331W:RS
4700p:PT
100025V
0.47:MPS
4700p:PT
1k:CHIP
1k:CHIP
1k:CHIP
1k:CHIP
47k 47k0.01B:CHIP0.01
B:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
100k:CHIP
0.01B:CHIP
1k:CHIP
100k:CHIP
100k:CHIP
100k:CHIP
100k:CHIP
11/2W:FPRD
220
10P:VH
1k:CHIP
100k:CHIP
100k:CHIP
1k:CHIP
1k:CHIP
1k:CHIP
47100V
10:FPRD
0.022:PT
0.1100V:PT
3300p200V:PT
EGP10GPKG
0.1100V:PT
0.22100V:PT
270k:RN-CP
5.1k:RN-CP
33400V
470:CHIP
22:FPRD
1k:CHIP
100k:CHIP
47k
47k
47k
10k:CHIP
681/2W
ERA91-02TP1
470pCH:CHIP
4.7k:CHIP
39k:RN-CP
0.01B:CHIP
0.01B:CHIP
68:10W
15µH
47
C57710
220:CHIP
220:CHIP
3.3k:RN-CP
18k:RN-CP
4PWHT
470p2kVB
1k:CHIP
2.2250V
7PWHT
:S-MICRO
470p
CH:CHIP
0.1
B:CHIP
1000pCH:CHIP
47pCH:CHIP
0.01B:CHIP
0.01B:CHIP
0.01B:CHIP
8.2k:RN
10k:RN-CP
22p500VCH
11/2W:FUSE
47k 47k 47k
11/2W:FPRD
6800pB:CHIP
1k:CHIP
4.7:FPRD
4.7:FPRD
470:FPRD
1k:CHIP
10k:CHIP
47k:CHIP
330k1/2W:RC
4.7k1/2W:RC
1k1/2W:RC
4.7:FPRD
1k:CHIP
1.2k:RN-CP
1.2k:RN-CP
1k1/2W:RC
0.22:MPS
6.83W:RS
0.01B:CHIP
0.01B:CHIP
1mH
10025V
47016V
10025V
4700p100V:PT
4700p2kV:E
1k:CHIP
10R92110k
47
0.1
B:CHIP
10k:RN-CP
100k
47016V
25V 4.7k:CHIP
10025V
680k:RN-CP
47k:CHIP
100k:CHIP
3.3
22k:CHIP
10
100:CHIP
1k:CHIP
6PWHT
:S-MICRO
100µH
100µH
472W:RS
1k:CHIP
0.22:MPS
22
FMQ-G5GS
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77
1SS133T-77 1SS133T-77
1SS355TE-17
220:CHIP
2.2 10W :RN
1k:CHIP
100p2kV:HR
470p2kVB
100p2kV:HR
1SS133T-77
1SS133T-77
ERA34-10TP1
1k:CHIP
22k:RN
C5660.01:PT
152W:RS
4.7k:CHIP
HZS13NB2TD
D5SC4M
HZS5.1NB2TD
HZS5.6NB2TD
HZS5.1NB2TD
HZS16NB2TD
HZS16NB2TD
HZS33NB2TD
HZS4.7NB2TD
HOC
22k:CHIP
1k:CHIP
1k:CHIP
1001/2W:RN
1001/2W:RN
:FBT
0.01B:CHIP
10
33k:RN-CP
4.7k:RN-CP
4.7k:CHIP
10pCH:CHIP
10pCH:CHIP
10k:RN-CP
470k1/2W:SURGE
0.056400V:PP
3900p1.8kV
25P:FFC
25P:FFC
47k:CHIP
1
1SS133T-77
10k:CHIP
R55910k:CHIP
C5672200pB:CHIP
0.33250V:PP
220:CHIP
4700pB:CHIP
15k:RN-CP
12k:RN-CP
12k:RN-CP
3.9k:CHIP
47k:RN-CP
R151747k
:CHIP
68pCH:CHIP
1SS355TE-17
1SS355TE-17
4.7mH
33k:RN-CP
GP08DPKG23
HLC
0.01B:CHIP
1k:CHIP
100k:CHIP
0.027400V
0.82250V:PP
0.39250V:PP
0.22250V:CQ
0.1250V:PP
1.2250V:PP
0.473W
22100V
1k:CHIP
2.7k:CHIP
2.2k:CHIP
HZS5.1NB2
1SS355TE-17
0.125V
B:CHIP
4725V
1000p1kV:E
10
ERA22-06AVRBT
39k:RN-CP
47k:RN-CP
22k:RN-CP
R5114.7k:CHIP
C5044700pB:CHIP
0:CHIP
22k:RN-CP
22k:RN-CP
100
R151010k :CHIP
10k:CHIP
2.2k:CHIP
10k:CHIP
R1518100:CHIP
10k:RN-CP
10k:CHIP
1k:CHIP
4.7:FPRD
39k:CHIP
10k:CHIP
HCT
2201/2W:FUSE
220
2.2k:CHIP
2.7k:CHIP
1.8k:RN-CP
2.2k:CHIP
1.1µH
1.1µH
HST
0.01B:CHIP
1002W:RS
2000p1.2kV:PP
180p
CH:CHIP
HZS13NB2TD
270p
CH:CHIP
0.001B:CHIP
HDT
DFT
39k:RN
1.5k:RN-CP
0.125V
B:CHIP
10k:CHIP
2.7k:CHIP
0.047200V:PT
0.047200V:PT
0.022200V:PT
0.022200V:PT
2.2mH
473W:RS
R1515473W:RS
22k:RN-CP
2200pB:CHIP
18k:RN-CP
5.6k:RN-CP
12k:RN-CP
:RN-CP
4.7k:RN-CP
8.2k:RN-CP
4700pB:CHIP
0.047B:CHIP
12k:RN-CP
4.7k:RN-CP
2.2250V
331/2W:FPRD
1001/2W:FPRD
100pCH:CHIP
4700pB:CHIP
0.01CH:CHIP
1.1µHFB5061.1µH
22
221SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
4.7k
0.15400V
DTC114GKARELAY DRIVE
2SK3262S-CAP CHANGE
2SK3262S-CAP CHANGE
2SK3262S-CAP CHANGE
2SK3262S-CAP CHANGE
2SK3262S-CAP CHANGE
2SK3262S-CAPCHANGE
2SK3262S-CAPCHANGE
2SK3262S-CAPCHANGE
2SK3262S-CAP CHANGE
2SC2412KTH DET
2SC2412KTH DET
BA9759FPIN
CONTROL
DTA143TKAGAIN SW
2SB1565EF
Q5232SC2412K
HL OUT
2SD2394-EFHL OUT
BA10324AFAMP
2SA1037AKPIN AMP
2SC2412KBUFF
2SC3209LKH CENT
LA6500-FAH CENT OUT
2SJ569LSPIN OUT
2SC2411KPIN DRIVE
2SA1036KPIN DRIVE
2SC2412KH DRIVE
2SA1036KH DRIVE
8PWHT
:S-MICRO
2PWHT:VH
ERA34-10TP1
BA9758FSHV CONTROL
2SC2411KHV DRIVE
2SA1036KHV DRIVE
2SK2655HV OUT
DTA114GKAHV DET
DTC114GKAHV DET
2SC2459H DRIVE
2SC3421H DRIVE
2SA1358H DRIVE
2SA1049H DRIVE
2SC2362KGH DRIVE
2SA1037AKV DRIVE
2SC4634LS-CB11V DRIVE
LA7841LV DY OUT
HZS12NB2TD
2SC5570 H OUT
2SC3746H OUT10mH
1SS355TE-17+B
15V-15V
400V
400V
2
1
S0
S1
S2
S3
S4
S5S5-1
S6
HDF
ABL
S5
S6
S0
S1
S2
S3
S4
HCENT
HCENT
HSPBAL
V+
V-
V+
V-
HSIZE
HSP
THDET
HDF
VDF
RXD
TXD
HTR
DGUS
ECO
HD
HVDET
VSHAPE
VRET
VRET
VSHAPE
HSP
HSPBAL
HVDET
HCENT L
HCENT N
HCENT N
HCENT H
HCENT L
HLIN
HLIN
HFBP
HFBP
THDET
HD
VDF
HSIZE
ABL
ABL_DET
S5≠≠≠
S5
≠≠≠
HCENT H
HTR
DGUS
ECO
TXD
RXD
+VIN
VEE
VCC
OUT
-VIN
H.DY H
H.DY H
H.DY C
H.DY C
NC
NC
V.DY H
V.DY C
GND
S
G
D
NC
GND
GND
NC
+220V
+220V
GND
-15V
GND
GND
HTR SW
+80V
+15V
+12V
GND
STBY+5V
1W+5V
ECO SW
PWR SW
DGUS SW
G2(NC)
G2
STBY+5V
RXD
TXD
GND
OUT + Vcc
VEE - OUTOUTVcc
UPPUMP
1
CN507
PVCC
PWMOUT
PGND
SLOW SWVREG9
SAWR
SAWOUT
SGND
HDIN
HVD
AGC
+
-
PWMOUT
PVcc
NC
SAWOUT
NC
SGND
HDIN
DELAY
VREG9
SVcc
PGND
HVDCAP
NCSLOW SW
NC
ERROUT
GND
GND
GND
GND
GND
+15V
+15V
-15V
TH DET
-15V
HDF
GND
VDF
HV DET
ABL
HSPBAL
HCENT
TXD
RXD
GND
HSHAPE
STBY+5V
HSIZE
1W+5V
GND
S4
GND
GND
GND
HD
GND
S1
S3
S0
S2
S6
GND
S5
ECO SW
GND
PWR SW
VSHAP
VRET
+12V
HFBP
GND
STBY+5V
HLINBAL
DGUS SW
HTR SW
NC
MIX+
MIX-
MIXOUT
VCC
REFIN
ERRIN
NC
ERROUT
O2
-2
+2
VCC
+1
-1
O1
O3
-3
+3
VEE
+4
-4
O4
D(DEFLECTION)
H CENT H
H CENT N
H CENT L
TO G BOARD CN654
1P
TO CHASSISTO A BOARD CN406
HV ADJ
TOA BOARD
FV
TOA BOARD
FC
TO G BOARD
CN653
TO G BOARD
CN650
TO ECS
TO N-a BOARD
CN010
TO N-a BOARD
CN011
H.DY
V.DY
FASTEN
HV TUBETO PICTURE
B-SS3484<J..>-D..-EPS05
D9141SS133T-77
S5-1
1
2
5
8
9
10
6
FB901
D906
R941
T901
R575
1.1µH
YG911S3RD924
RD12ES-T1B2
C5641
100:CHIP
HRC
7.5k
2SJ569LSHV REG SW
ABL_DET
IC
IC501 C-4IC502 A-1IC503 C-4IC701 A-5IC901 C-1
TRANSISTOR
*Q501 B-5 -Q502 A-4 1
Q503 A-4 1Q504 C-4 1
Q505 D-4 1Q506 B-5 -Q507 C-5 -Q508 A-2 -Q509 A-4 -Q510 C-5 -Q511 C-5 -Q512 C-5 -Q513 C-5 -Q514 B-2 -Q515 A-3 -Q516 B-4 -Q517 D-5 -Q518 B-4 -Q519 D-4 1
Q520 B-5 1Q521 B-5 1
Q522 C-5 1
Q524 B-3 1Q525 C-5 -Q526 C-4 1
Q701 D-4 -Q702 D-3 -Q703 D-4 -Q704 D-3 -Q705 D-4 -Q706 D-3 1
Q707 D-3 -Q903 B-3 1
Q904 C-3 1
Q905 C-3 -Q906 C-3 -Q907 B-2 1
Q908 B-2 1
5-21 5-22
— D BOARD —
D DEFLECTION
NOTE:The circuit indicated as left contains high voltage of over600 Vp-p. Care must be paid to prevent an electric shock ininspection or repairing.
1 2 3
4 65
• D BOARD WAVEFORMS
54.5 Vp-p (H)
1.9 Vp-p (H)
2.1 Vp-p (H)
568 Vp-p (H)8.8 Vp-p (H)
50.6 Vp-p (H)
• D BOARD SEMICONDUCTOR LOCATION
* : Refer to Terminal name ofsemiconductors in silk screenprinted circuit (see page 5-10)
DIODE
*D504 D-4 3D505 A-1 -D506 A-4 -D507 A-2 -D508 A-3 -D509 B-2 -D510 A-1 -D511 A-2 -D512 B-3 3
D513 B-2 -D514 B-3 -D515 B-2 -D516 B-4 -D517 B-3 -D519 C-4 3D520 D-4 3
D522 C-4 3
D701 D-4 -D702 D-4 -D703 D-4 -D707 A-5 -D708 A-5 -D709 B-2 -D710 D-3 -D901 B-1 -D902 B-2 -D904 B-3 3D905 C-3 -D906 C-3 -D907 B-3 -D908 C-3 -D909 C-1 -D910 C-2 -D912 C-2 -D913 B-1 -D914 C-2 -D915 C-2 -D917 B-2 3
D918 B-1 -D919 B-1 -D920 B-1 -D921 B-2 3D922 C-3 -D924 C-4 3
VARIABLERESISTOR
RV901 B-1
A
B
C
D
1 2 3 4 5
5-23 5-24
(4) Schematic Diagrams of N ( a, b, c) Board
Schematic diagram
NNNNN-a board l
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
• Divided circuit diagram
One sheet of N board circuit diagram is divided into three sheets,
each having the code N-a to N-c. For example, the destination
ab1 on the code N-a sheet is connected to ab1 on the N-b sheet.
a b 1
Ref. No.
Circuit diagram division cod
-15V
+15V
VCC+4.5V
STBY+5V
+12V
STBY+5V
SUB+5V
1W+5V
1W+5V
+15V
-15V
12
34 5
67
8
12
34
56
7 89
1011
1213
14
12
34
56
78
910
1112
1314
1516
1718 19
2021
2223
2425
2627
2829
3031
3233
3435
36
12
34
56
7 89
1011
1213
14
123456789
1
2
3
4
5
6
7
8
12345678910
11
12
13
14
15
16
17
18
19
20
21
22
23
24
2512345678910
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25 1 2 3 4 5 6 7 8 9 10
11
12
13
14
15
16
17
18
19
20
21
C064
C063
C071
C069
C075
C074
C073
C070
C079C080
C091
R1060R1061
C093
R1028
R1024
R003
R004
R014
R054
R1030
R1031
R1032
R1033
R1034
R1035
R1037
R1038
R1041
R1042
R1043
C082
C089
C066
C067
R039
R040
R081
R1025
R1040
R007
R008
C001
R009
R053
C012
C011
R1006
R1007
R022
R1029
D001
D002
D003
D004D015
C078
D025
R1049
R1051
R1070
R1058
C083
C084
C085
C087
D022
D023
D024
R1045
R1050
R1059
R018
R017
R016
R015
R020
R019
R021
R025
R026
R005
R006
R1053
R1057
R1054
R010
C002
R085
R082
R1056
D021
L002
R048
D012
D010
D009
D008
R059
R060
C094
C099
R058
R062
R063
R064
R075
R076
CN001
R1039
C068
R030
R034
L003
C072
R1027
R032
R044
R1022
R1023
R045
C065
FB003
D016
R024
R1026
C1005
R1047
CN002
R055
IC011
Q011
C077
IC010
Q003
Q002
Q001
D026
D018
Q009
CN010
R031D017
IC004
IC005
Q006
Q004
D020
Q005
Q007
CN007
CN011
R1052
R1055
R047
FB002
FB001
R086
3300p
25V
CH:CHIP
2200p
CH:CHIP680p
B:CHIP
0.1
B:CHIP
100p
CH:CHIP
680p
CH:CHIP
0.1
B:CHIP
1000
16V
0.01
B:CHIP47
100
16V
10k
:CHIP10k
:CHIP
0.1
B:CHIP
680
:RN-CP
18k
:RN-CP
100
:CHIP
100
:CHIP
1k
:CHIP
15k
:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
47
25V
0.01
B:CHIP
2200p
CH:CHIP
0.1
25V
B:CHIP
100
:CHIP
100
:CHIP
1k
:CHIP
2.2k
:CHIP
2.2k
:CHIP
0.001
B:CHIP
2.2k
:CHIP
4.7k
:CHIP
47
0.1
B:CHIP
100:CHIP
100:CHIP
1PS226
1PS226
1PS226
1PS226
MA151WK
0.22
:MPS
10k
:CHIP
100k
:CHIP
2.2k
:CHIP
10k
:CHIP
4.7k
:CHIP
R1063
4.7k
:CHIP
10k
:CHIP
1k
:CHIP
1k:CHIP
47:CHIP
47:CHIP
4.7:FPRD
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
100:CHIP
1k:CHIP
1k:CHIP
10k
:CHIP
2.2k
:CHIP
0.001
B:CHIP
1k:CHIP
1k:CHIP
10k
:CHIP
R046
10k
:CHIP
0.01
B:CHIP
10
0.01
B:CHIP
10
MA151WK-TX
MA151WK-TX
MA151WK-TX
1PS226-115
1k:CHIP
1k:CHIP
100:CHIP
100:CHIP
1SS355TE-17
100µH
1k:CHIP
HZS5.6NB2TD
HZS5.6NB2TD
HZS5.6NB2TD
HZS5.6NB2TD
5.6k
:CHIP
100
:CHIP
0.22
:MPS
1000
25V
0.1
25V
B:CHIP
0.1
25V
B:CHIP
21P:FFC
1000µH 1k
:CHIP
1k:CHIP
2.2k
:CHIP
2.2k
:CHIP
27
:RN-CP
27
:RN-CP
27
:RN-CP
270
:RN
270
:RN
2.2k
:CHIP
3.9k
:RN-CP
1.8k
:RN-CP
1k
:CHIP
2.2k
:RN-CP
2.2k
:RN-CP
1
1.1µH
HZS5.6NB2TD
100:CHIP
470p
B:CHIP
330k
:CHIP
10k
:CHIP
8P:S-MICRO
15k:CHIP
24LC21AT/SN
ROM
2SA1037AK
HD SW
0.1
B:CHIP
LA7865M-TLMH.V.OSC,AFC,H.DRV,V.SHAPE
2SA1037AK
CURRENT
MILLER
2SA1037AK
CURRENT
MILLER
2SA1037AK
CURRENT
MILLER
1PS226-115 HZS5.6NB2TD
2SC2412K
ABL BUFF
25PFFC/FPC
5.6k
:RN-CP
HZS5.6NB2TD
TC74VHCT74AFT(EL
ECO DET
TC74VHCT74AFT(EL
ECO DET
DTC123EKA
ACTIVE OFF DET
DTA124EUA
ACTIVE OFF DET
1SS355TE-17
DTA114GKA
ACTIVE
OFF DET
DTC124EKA
ECO SW
9PWHT
:S-MICRO
25P FFC/FPC
10k:CHIP
1k:CHIP
1k:CHIP
1.1µH
1.1µH
1k:CHIP
DGS
HTR
SOGDET
SOG
CBLK
CLP
VS1
HS/CS1
VS2
HS/CS2
SDA
SCL
HSIZE
HSHPBAL
VDF
HVDET
THDET
LED0
LED1
S0
S1
S2
S3
S4
S5
INPUTSEL
TXD
RXD
HSP
S6
HLINBAL
PWR_SW
VRET
HOST G 1
HOST G 2
HSOUT1
ABLDET
HCENT
VSHPLVL
DVSHAPE
VDC
HSOUT
HPHASE
HFREQ
MOIRE
VSAWRST
VSH
AFCSW
HPLL
HFBP
ECO_SW
HC1
VC1
HC2
VC2
HC1
PRT_DET
ENV
KEYDET
INPUT_SW
OFFDET
VSOSD
VSOSD
DSDA1
DSCL1
VC2
ECO
SOGDET
HC2
VC1
ECO_SW
HDSW
NC
NC
NC
VSS
VCLK
SCL
SDA
VCC
CLP
GND
C.BLK
GND
ABL(NC)
GND
SCL
SDA
LED0
LED1
KEY DET
GND
GND
NC
NC
NC
HOST GND 2(NC)
DDC+5V 1
HS/CS2
VS2
V.SYNC
H.SYNC
GND
GND
GND(NC)
STBY+5V
1W+5V
+15V
+15V
-15V
-15V
GND
HV DET
ABL
TH DET
GND
HSHAPE
HSIZE
TXD
RXD
GND
GND
HDF
VDF
GND
GND
HCENT
STBY+5V
1W+5V
GND
GND
GND
GND
S0
S1
S2
S3
S4
S5
S6
GND
PWR SW
DGUS SW
HTR SW
GND
HFBP
HD
GND
VSHAPE
GND
VRET
GND
ECO_SW
STBY+5V
HLINBAL
HSPBAL
VSHPLVL
VDC
VSHP_C
GND
HS
HPHASE
HSDLY
AFC_FIL
VCO_C
GND
FILTER
REG9V
S/HC
VSAWRST
VSH
VSHAPE
VCC12
FBP
AFC_SW
NC
HPLL
HD_DUTY
HD
VCC12
IREF_RFBP_DLY1
HFREQFBP_DLY
NC
NC
NC
NC
NC
NC
VCC4.5 DVSHAPE
VCC
2CLR
2D
2CK
2PR
2Q
2Q
1Q
1CLR
1D
1CK
1PR
1Q
GND
VCC
2CLR
2D
2CK
2PR
2Q
2Q
1Q
1CLR
1D
1CK
1PR
1Q
GND
INPUT_SW
HFBP
SYNC_ON_G
G.SYNC_DET
DDCSCL 1
DDCSDA 1
HOSTGND 1
INPUT_SEL
ENV_DRI
HS/CS 1
VS 1
TO CONNECTOR
PANEL
ac1
ab7
ab6
ab5
ab3
ab4
ab2
ab1
(H.OSC,V.OSC,AFC,H.DRV,V.SHAPE)
)
)
TO A BOARD CN403TO D BOARD CN504TO D BOARD CN505TO H BOARD CN801
+12V
N-a
INPUT2
B-SS3484<J..>-N..-P1-EPS05
D036
HZS5.6NB2TD
D038
UDZ-TE-17-2.2B
D037
HZS5.6NB2TD
5-25 5-26
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
J
STBY+5V
STBY+5V
VCC+4.5V
+15V
+15V
STBY+5V
STBY+5V
STBY+5V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
12
345
67
8 12
345
67
8
23
45
67 8
910
1112
1314
12
34 5
67
8
C022
C021
C020
C019
C018
C017
C016
C015
C024
C025
C026
C013
C023
C043
C041
C040
C050
C049
C039
C038
C037
C055
C056
C057
C059
C062
C086
C090
C095
C096
D029
C097
R078
X001
R5005
R5006
C5004
C5002
R5007
R5015
C5003
C5005
C5008
R5010R5011
GS5001
D013
R029
R035
R036
R037
R5003
R043
C053
C036
R049
R080
R079
C008
C1007
C1004
C1006
R056
R057
R061
C014
R067
R066
C051
C048
C047
C046
C045
C044
C042
R1003R1002
R1001
R099
R098
R097
R096
R095R094
R093R092
R091
R090
R1021
R1020
R1008
C054
C058
R1014
R1013
R1012
R1011
R1010
R1009
R1016
R1017
R1018
R1019
C061
C027
R1036
R1005
C033
R1064
D027
D028
R1067
R1066
R1065
R1068
R1069
C098
C028
C029
C5009
C003
C005
R1004
C052
C006
C007
R042
C031
C1003
R1044
R077
R084
IC006
Q010
Q012
Q008
IC002
IC003
IC001
0.01
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
0.001
B:CHIP
0.001
B:CHIP
100
25V
22
0.01
B:CHIP
22
10
10
10
10
10
10
10
47
25V
22
10
10
100
25V
0.01
B:CHIP
0.01
B:CHIP
2200
10V
0.01
B:CHIP
HZS5.1NB2TD
10
1M
:CHIP
24.756MHz
22k
:CHIP
10k
:CHIP
47
25V
10
1k
:CHIP
1k
:CHIP
100
16V
47
25V
47
25V
0:CHIP
10k
:CHIP
HZS10NB2TD
10k
:CHIP
10k
:CHIP
2.2k
:RN-CP
10k
:CHIP
0:CHIP
1k
:CHIP
0.01
B:CHIP
0.022B:CHIP
10k
:CHIP
0:CHIP
0:CHIP
0.1
25V
B:CHIP
0.1
B:CHIP
R023
4.7k
:CHIP
R1071
22k
:CHIP
0.01
B:CHIP
2200p
B:CHIP
10k
:CHIP
10k
:CHIP
1k:CHIP
0.01
B:CHIP
10k
:CHIP
1k
:CHIP
0.01
B:CHIP
0.01B:CHIP
0.022B:CHIP
0.022B:CHIP
0.022B:CHIP
0.022B:CHIP
0.01B:CHIP
1k
:CHIP1k
:CHIP
1k
:CHIP
1k
:CHIP
10k
:CHIP
10k
:CHIP
4.7k
:CHIP
1k
:CHIP
1k
:CHIP
1k
:CHIP
1k
:CHIP
1k
:CHIP
10k:CHIP
4.7k
:CHIP
4.7k
:CHIP
4.7k
:CHIP
0.1
B:CHIP
2200p
CH:CHIP
1k
:CHIP
2.2k
:CHIP
2.2k
:CHIP
1k
:CHIP
1k
:CHIP
1k
:CHIP
1k
:CHIP
1k
:CHIP
1k:CHIP
1k
:CHIP
0.01
B:CHIP
0.1
B:CHIP
100:CHIP
1k
:CHIP
0.01
B:CHIP
1k
:CHIP
1SS355TE-17
1SS355TE-17
2.2k
:CHIP
10k
:CHIP
1.5M
:CHIP
2.2k
:CHIP
1k
:CHIP
0.01
B:CHIP
3p
CJ:CHIP
39p
CH:CHIP
0.1
25V
B:CHIP
0.01
B:CHIP
150p
CH:CHIP
1k
:CHIP
100
16V
22p
CH:CHIP
22p
CH:CHIP
10k
:CHIP
10
47
25V
4.7k
:RN-CP
10k
:CHIP
10k
:CHIP
R1062
1k
:CHIP
R1015
1k
:CHIP
TL082CPS-E20ABL DET AMP
2SA1037AKINV.
DTC124EKAINV.
DTC114GKAT146
SW MM1170BFB
WDT
M24C16-MN6T
EEP ROM
CXD8744QCPU/DSP
STBY+5V
GND
HSOUT
AFCSW
VSH
HFBP
HFREQ
HPHASE
VDC
DVSHAPE
VSHPLVL
VS2
HS/CS2
HS/CS1
VS1
VSAWRST
MOIRE
VY
VX
HVDET
THDET
ABLDET
VRET
ENV
KEYDET
INPUTSEL
S0
S1
S2
S3
S5
S6
MOIREPLS
DSCL1
MOIREPLS
SOG
HTR
PWR_SW
DGS
CLP
CBLK
TXD
RXD
SDA
SCL
HPLL
DSDA1
HSOUT1
S4
OFFDET
HSHPBAL
VDF
VCONV
HSP
HSIZE
HCENT
ROTATION
HLINBAL
HCONV
LCCNS
LCCLT
LCCRT
LCCLB
LCCRB
LED0
LED1
HDSW
ECO
INPUT_SW
PRT_DET
HOST G2
HOST G1
VY
VX
A0
A1
A2
VSS
VCC
SCL
SDA
TC
NC
CK
GND
VS
RCT
VCC
RESET
VPP
MVBIAS
P10/A0
P11/A1
P12/A2
P13/A3
P14/A4
P15/A5
P30/A8
P31/CSIO
P40/D0
P41/D1
P42/D2
P43/D3
P44/D4
P45/D5
P46/D6
VDD1
P47/D7
P32/RD
P33/WR
P34/CLK
P35/SCOUT
ICE
TEST
P51/INT0
P52/INT2
P53/INT3
P54/INT4
P55/INT5
P90
RESET
VDD2
P50/X1OUT
GND1
SCK2/P85
RXD
TXD
UBI1
UBI2
UBI3
UBI4
GND2
UOUT1
UOUT2
UOUT3
PA0
PA1
PA2
GND3
PA3
PA4
PA5
PA6
OSCVSS
XTB
XTO
OSCVDD
UOUT4
UOUT5
UOUT6
P91
GND4
DAC0
AVSS1
DAC1
AVDD1
AIN1
AIN2
AIN6
AIN7
AIN8
AIN9
AIN10
AVDD2
AIN11
AIN12
AIN13
GND5
INT1
P92
P93
P94
P95
UOUT7
UOUT8
VDD3
UIN1
UIN2
GND6
UIN3
UIN4
UIN5
UIN6
GND7
UPWM1
VDD5
VDD6
UPWM2
GND8
GND9
UPWM3
VDD7
VDD8
UPWM4
GND10
UPWM5
GND11
UPWM6
VDD9
UPWM7
VDD10
UPWM8
GND12
GND13
UPWM9
VDD11
UPWM10
GND14
GND15
UPWM11
VDD12
UPWM12
VDD13
UPWM13
GND16
UPWM14
GND17
UPWM15
VDD14
VDD15
UPWM17
UPWM18
GND18
GND19
UPWM19
UPWM20
VDD16
VDD17
UPWM21
UPWM22
GND20
GND21
VDD18
HDCONT
VDD
WC
SDA2
SCL2
P82
SDA1
SCL1
WDP
EEPWC
P17/A7
P16/A6
P96
UBI5
CLPDLY
HPHASESW
AIN5
AIN4
AVSS2
AIN3
AIN0 TEMP
MOIRECONT
HDF0GEOMAGNETIC SENSOR
Vcc0
-+
0-
+VDD
N
ab7
ab6
ab5
ab3
ab4
ab2
ab1
bc3
-b
bc2
bc1
(µ-COM,GEO MAGNETIC SENSOR)
B-SS3484<J..>-N..-P2-EPS05
5-27 5-28
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
Schematic diagram
NNNNN -c board l
Schematic diagram
Ò NNNNN -b board
STBY+5V
-15V
+15V
+15V
-15V
-15V
+15V
STBY+5V
12
34
5 67
89
10 12
34
5 67
89
1012
34
5 67
89
10 12
34
5 67
89
10
12123456 12345678
R5113
R5108
R5119
C5105
C5110
R5115
R5122
R5205
R5206
C5205
R5313
R5319
C5305
C5310
R5315
R5322
R5208R5419
R5409
R5413
R5422
R5415
R5316
R5310
R5116
R5110
R5207
R5410
R5416
C5501
C5602
C5607
C5606
FB5303
FB5301
FB5103
FB5101
FB5201
FB5601
FB5401
FB5403
1.1µH
C5413
R5509
R5510
R5507
R5508
C5106
C5108
C5203
C5101
C5306 C5308
C5303
C5301
C5304
C5206
R5109
R5309
R5308
C5103C5408
C5403
C5404
C5409
R5407
R5408
C5401
R5502
R5506
R5503
R5504
R5505
R5605
R5607
R5602
R5603
R5610
R5604
R5209
IC5301
CN5002CN5003
IC5101
CN5001
IC5401IC5201
C5406
R5406 10k
:CHIP
4.7
:CHIP
10k
:CHIP
47
25V
47
25V
221W
:RS
221W
:RS
10k
:CHIP
221W
:RS
0.1
25V
B:CHIP
10k
:CHIP
10k
:CHIP
47
25V
47
25V
221W
:RS
221W
:RS
6.8k
:CHIP
100k
:CHIP
4.7
:CHIP
100k
:CHIP
120
2W
:RS
150
2W
:RS
10k
:CHIP10k
:CHIP
10k
:CHIP
10k
:CHIP
10k
:CHIP
22k
:CHIP
22k
:CHIP
47
0.1
B:CHIP
0.1
25V
B:CHIP
0.01
B:CHIP
1.1µH
1.1µH
1.1µH
1.1µH
1.1µH
1.1µH
1.1µH
0.1
25V
B:CHIP
1.2
:FPRD
1.2
:FPRD
1.2
:FPRD
1.2
:FPRD
0.1
25V
B:CHIP 0.125V
B:CHIP
0.1
25V
B:CHIP
0.1
25V
B:CHIP
0.1
25V
25V
B:CHIP 0.125V
B:CHIP
0.1
25V
B:CHIP
0.1
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
4.7
:CHIP
4.7
:CHIP
4.7
:CHIP
0.1
25V
B:CHIP470p
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
0.01
B:CHIP
33k
:CHIP
4.7
:CHIP
0.1
25V
B:CHIP
22k
:CHIP
6.8k
:CHIP
22k
:CHIP
47k
:CHIP
47k
:CHIP
100k
:CHIP
681W
:RS
22k
:CHIP
15k
:CHIP
4.7
:CHIP
22k
:CHIP
4.7
:CHIP
LA6515AMP
8PYEL
:S-MICRO
2PWHT
:S-MICRO
LA6515AMP
6PWHT
:S-MICRO
LA6515AMP LA6515
AMP
0.125V
B:CHIP
27k
:CHIP
ROTATION
VCONV
LCCNS
HCONV
LCCLB
LCCLT
LCCRB
LCCRT
V.S1
OUT1
-
+
VCC
V.S2
-
+VEE
OUT2
V.S1
OUT1
-
+
VCC
V.S2
-
+VEE
OUT2
V.S1
OUT1
-
+
VCC
V.S2
-
+VEE
OUT2
ROTATION-
V.S1
OUT1
-
+
VCC
V.S2
-
+VEE
OUT2
LCC-LT(+)
LCC-LT(-)
LCC-LB(+)
LCC-LB(-)
LCC-RT(+)
LCC-RT(-)
LCC-RB(+)
LCC-RB(-)
LCC-NS(+)
LCC-NS(-)
V CONV(+)
V CONV(-)
H CONV(+)
H CONV(-)
ROTATION+
N
bc3
bc2
bc1
(H.V.CONV,LCC)
-c
ac1
V.CONV
H.CONV
ROTATION
LCC-LT
LCC-LB
LCC-RT
LCC-RB
LCC-NS
B-SS9116<NH.>-N..-P3-EPS05
IC
IC001 C-2IC002 C-2IC003 C-2IC004 B-2IC005 B-2IC006 D-1IC010 C-2IC011 B-2IC5101 A-2 A-2IC5201 B-2 B-2IC5301 A-1 A-2IC5401 B-1 B-2
TRANSISTOR
*Q001 C-1 1
Q002 C-1 1
Q003 C-1 1Q004 B-1 2
Q005 C-1 2
Q006 C-1 2Q007 B-3 1
Q008 C-2 1
Q009 D-3 1Q010 C-1 1
Q011 C-2 2
Q012 D-2 2
DIODE
*D001 A-1 7
D002 A-1 7
D003 C-3 6D004 C-1 7
D008 C-3 C-1 –D009 C-3 C-1 –D010 C-3 C-1 –D012 C-3 C-1 –D013 C-2 C-2 –D015 B-2 8
D016 B-1 B-2 –D017 B-1 B-2 –D018 B-1 B-2 –D020 B-1 3
D021 C-3 3D022 C-3 8
D023 B-2 8
D024 B-2 8D025 B-1 6
D026 B-2 6
D027 D-2 3D028 D-2 3
D029 D-3 D-1 –D036 D-3 D-1 –D037 D-3 D-1 –D038 C-1 3
CRYSTAL
X001 C-2 C-1
5-29 5-30
N µ-COM, V.CONV, H.CONV,LCC, GEO MAGNETIC SENSOR
— N BOARD (Component Side) —— N BOARD (Conductor Side) — • N BOARDSEMICONDUCTORLOCATION
* : Refer to Terminal name ofsemiconductors in silk screenprinted circuit (see page 5-10)
A
B
C
D
1 2 3
A
B
C
D
1 2 3
Component( )SideConductor( )Side
Component( )SideConductor( )Side
Component( )SideConductor( )Side
Component( )SideConductor( )Side
(5) Schematic Diagram of G Board
5-31 5-32
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
Schematic diagram
GGGGG board l
5.7 2.5 180
4.0
11.9
4.0
0.7
0.14.0
0
14.8
14.3
0.2 14.3
0.2
11.4
11.4
11.2
5.06.86.8
6.1
0.1
1.20.3
6.7
5.6
4.9
2.5
2.4
5.6
6.8
2.8
6.8
5.0
4.8
5.5
5.0
1.2
4.7
1.2
3.5
380
351-1.1
348
-1.1
-1.0 348
2.5
13.7
380
2.4
090.6
0.1
240
15.937915.2181
0
0
0.5
16.1188
189
1.4
9930
4.7
0
3.24.9
016.1
1.514.7
2.5 0
2.1
12345
1
2 3
4
1
2
3
1 8
5
2
3
4
6
1
2
3
1
2
3
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
1 2 3 4 5 1 2 3 4 51 2 3 4
5678
1
2
3
4
6
7
5
1
2
4
3
1
2
3
4
1
2
3
1
2
4
3
1 2 3 4 5 6 7 8 9 10
1
1
2
3
4
5
6
7
8
9
10
11
12
2 3 4 5
711121 6
89
1
2
3
1
2
3
4
5
6
1
2
3
4
5
6
7
S
TH601
F601
SG601
THP601
VDR601
VDR602
PS650
CN603
CN602
CN601
C606D610
L611
C605
D690
C603 C604
R601
C602
T601
C601
D692
R693
PH630
D631
FB630
R614
C612 C613
C610
R623
R624
C623 C624
C625
D655R657
C626
D683
D681
R661
D660
D661
C666
D663
R656
D656
D654
D653
C659
C658
D652
D651
R653
D650
C662
CN654
PH620
C682
CN652
CN653
CN650
C692
R686
R659
R685
R665
R683
R655
R695
R658
R664
R684
R694
R613
R667
R652
R673
D637
R628
R629
R627
R622
R621
R649
R663
R666
R668
R681
R682
D664
L650
L651
D665
R636
C631
C680
R680
R688
C607
C650 C651
C652 C653
C654
C656
C655
C657
C660
C665
C681
C683
C686
L680
C621
C622
C627
D632
C687
R610R611
L652
R696
L653
C661
D666
R674
R612
RY603
T621
R677
R678
C611
L610
T630
RY602
R630
R633
R634
R635
R670 R671
R672
R687
C629
C630
C633C634
D635
D682
R608
R609
R616
R617R618
R607
D620
D612
R602
R603
R604
R605
R606
R620
R625 R626
C663R662
R654
R650
JW604
JW605
D633
D680
D634
1.1µHFB632
R632
D613
T620
C614
CN604
R615
C620
C667
C684
C685 R675
R676
IC610
Q691
IC630
Q630
IC680
Q633
Q632
Q631
Q610
Q621
Q603
IC650
IC654
Q654
Q667
Q653
Q652
Q651
Q650
IC653Q670
IC652 IC651
Q671
2.0A
6.3A
3P
3PWHT:VH
4PWHT:VH
4700p250V
D4SB60L
4700p250V
330k 1/2W :SURGE
1275V
:LFT
1SS119
681/2W
ON3171-R
100k1W:RS
100k1W:RS
0.33:MPS
0.33:MPS
0.15:MPS
0.47:FPRD
0.15:MPS
1SS119
11/2W:FPRD
D2S4MTA1
D2S4MTA1
220010V
220010V
D4SBS4
470
D4SBL40
0.01:PT
ON3171-R
1275V
0.22:MPS
47
1SS1191SS119
0.45µH
68µH
100
10
4700p:PT
0.1B:CHIP
7PWHT
:S-MICRO
9P WHT :S-MICRO
6P WHT :S-MICRO
8PWHT
:S-MICRO
1SS11947k:CHIP
470k:CHIP
4.7k:CHIP
10k:CHIP
1k:CHIP
10k:CHIP
2.2k:CHIP
47k:CHIP
10k:CHIP
2.2k:CHIP
10k:CHIP
1k:CHIP
220:CHIP
10k:CHIP
4.7k:CHIP
1SS119
100
10025V
D1NL20U
D1NL20U
D1NL20U
RD22ESB2
RD12ESB2
RD22ESB2
1SS119
RD5.6ESB2
22µH
22µH
18k
47k:CHIP
22k:CHIP
68k:CHIP
22k:CHIP
22k
47k:FPRD
10k:CHIP
10k:CHIP
33k:RN
10k:CHIP
1k:CHIP
680010V
180k:RN
150k:RN
470p250VB
470p250VB
470p250VB
100250V
4.7250V
100100V
4.7100V
220025V
4725V
220025V
4725V
47
4710V
22µH
470p1kV:HR
470p1kV:HR
470p1kV:HR
4710V
4710V
4710V
10
P6KE200AG23
22µH
22µH
0.332W
1501/4W
2200p1kVB
4.7k
1SS119
100k:CHIP
2.7k:RN-CP
1.53W:RS
1SS119
1SS119
330450V
1400V
0.01:PT
470pB:CHIP
2200pB:CHIP
1000pB:CHIP
2.2
ERB38-06V1
RD20ESB2
YG802C09
RD9.1ESB
27k2W:RS
470k
470k:CHIP
470k:CHIP
100k:CHIP
100k:CHIP
10k:CHIP
6.8k:CHIP
0.472W
6.8k:RN-CP
1k12W:RS
0.11/2W:RF
11W:RS
11W:RS
3.3:FPRD
1M1/2W
1M1/2W
27k2W:RS
2.2k:CHIP
11/2W:RF
10k:CHIP
12k:RN-CP
12k:RN-CP
3.6k:RN-CP
22k:CHIP
PRT
AFC
SRT
1SS119
120:RN
PIT
RM11A
100p:CHIP
1P
6.8k
0.027800V:PP
4716V
4710V
10010V
5.1k:RN-CP
3.3k:RN-CP
MZ1530PFI
2SC3311ARELAY DRIVE
FA13842PREG
2SK2647-01MRREG SW
HA17431PA-TZRECT
2SC2412KVCC SW
2SC4015VCC SW
2SC4015VCC SW
2SA1309AVCC SW
2SC3311AREG SW
MX0842AB-FREG OUTSTART UP
DM-57N+220V SHUNT REG
µPC2912HF+12V REG
2SA1037AKSW
2SA1037AKPROTECT
2SC2412KPROTECT
2SC2412KPROTECT
2SC2458POWER SW
2SA1309APOWER SW
BA05T1W+5V REG
2SA1037AKPROTECT
BA05ST-V5STBY+5V REG
BA00AST-V5HEATER REG
2SA1037AKHEATER SW
15V
15V
1
2
3
4
5
7
8
1
2
4
3
1
2
6
5
4
3
NC
DGC
NC
NC
DGC
AC L
AC N
AC L OUT
NC
AC L IN
GND
GND
GND
-15V
H CENT H
H CENT N
H CENT L
+80V
GND
+220V
+220V
N.C
+12V
DRAIN
GATE
AC SEN
SOURCE
L SEN
GND
COMP
VCC
CATHODE
STBY+5V
1W+5V
ECO SW
PWR SW
DGUS SW
HTR SW
GND
+220V
N.C
+12V
HEATER
GND
+15V
GND
+80V
STBY+5V
CTL
Vcc
GND
OUT
NC
Vcc
CTL
OUT
GND
VADJ
N.C
(POWER SUPPLY)G
TO J BOARD
CN891
DGC
AC INLET
C1 C2
E1 B1 E2 B2
TO D BOARD
CN508
TO D BOARD
CN501
TO A BOARD
CN405
1W+5V
IN OUT
GND
IN OUT
GND
TO D BOARD
CN502
B-SS3484<J..>-G..-EPS05
R6370.1:RF
R6380.1:RF
G POWER SUPPLY
— G BOARD — • G BOARDSEMICONDUCTORLOCATION
5-33 5-34
* : Refer to Terminal name ofsemiconductors in silk screenprinted circuit (see page 5-10)
NOTE:The circuit indicated as left contains high voltage of over600 Vp-p. Care must be paid to prevent an electric shock ininspection or repairing.
IC
IC610 A-4IC630 C-3IC650 A-1IC651 C-1IC652 C-1IC653 C-1IC654 B-1IC680 C-2
TRANSISTOR
*Q603 A-3 -Q610 C-2 -Q621 C-3 -Q630 C-3 -Q631 B-3 -Q632 C-3 -Q633 C-3 1
Q650 B-2 -Q651 B-1 -Q652 C-1 1
Q653 B-1 1
Q654 B-2 1Q667 C-1 1
Q670 C-2 1
Q671 C-1 1Q691 C-2 -
DIODE
D610 B-4D612 C-2D613 A-4D620 C-2D631 C-2D632 B-3D633 B-3D634 C-3D635 C-3D637 C-3D650 A-2D651 B-2D652 A-1D653 A-2D654 A-1D655 B-2D656 B-2D660 B-1D661 C-2D663 C-1D664 B-1D665 B-1D666 C-2D680 B-2D681 C-1D682 C-1D683 C-2D690 C-3D692 C-4
A
B
C
1 2 3 4 5
5-5. SEMICONDUCTORS
5-35 5-36
M52749FP-TP
M52757FP-TP
µPC2912HF (12)
DTA114GKAT146DTA114TUA-T106DTA124EUA-T106DTC114GKADTC114GKAT146DTC124EKDTC124EKA-T1462SA1036K-Q2SA1036K-T-146-Q2SA1037AK-T146-QR2SA1037AK-T146-R2SA1162-G2SB709A-QRS-TX2SC1623-L5L62SC2411K-CQ2SC2411K-T-146-CQ2SC2412K-T-146-QR
DTA124ESADTA124ESA-TP2SA1175-HFE2SA1309A-QRSTA2SC2459-GR-TPE42SC27842SC2785-HFE2SC3311A-QRSTA
BA00AST-V5BA05ST-V5LA6500-FA
BA05T
BA10324AF-E2SN74HC04ANSSN74HC04ANSRTC74VHCT74AFT(EL)XRA10324AF
NJM2904MNJM2904M(TE2)TL082CPS-E20TL082M24LC21AT/SN
BA9758FS-E2
BA9759F-E2
CXD8744Q
CXD9514M
DM-57N
FA13842PM24C16-MN6TMM1170BFB
FA4301
HA17431PAHA17431PA-TZ
H8D2972
LA6515
LA7841L
LA7865M-TLM
MZ1530
MX0842AB-F
2SA1049-GR2SA1049TP-GR2SC2458-YGR2SC2458TP-YGR
2SA1358-Y2SC3421-Y
2SB1565EF2SC37462SC5022-02
2SC2362K-G2SC2362KG-AA
2SC3209LK2SC3209LK-TP
1 TOP VIEW
n
51
1
2 3
1 TOP VIEW
n
1 TOP VIEW
n
1 TOP VIEW
n
1TOP VIEW
n
1 TOP VIEW
n
MARKING SIDE VIEW
1
1 TOP VIEW
n
MARKING SIDE VIEW
1
14pin SOP
8pin SOP
20pin SOP
18pin SOP
160pin QFP
28pin SOP
5pin SIP
8pin DIP
15pin SIP
13
810
17
MARKING SIDE VIEW
1
1 18
1936
7pin SIP
42pin SOP
36pin SOP
1 2 3
2SC4015TV2
2SC5570(LBSONY)
2SD2394-EF
2SJ569LS-CB112SK2655-01R-F1652SK3262-01MR-F119
2SK2103T100
2SK2647-01MR-F91
D1NL20U-TRD2S4MFD2S4MTA1
D4SB60LD4SBL40D4SBS4D4SBS4-F
D5SC4MMA151WK-TX1SS184
EGP10DEGP10GPKG23ERA91-02ERA91-02TP1
ERA22-06AVRBTERA22-08ERA34-10TP1ERB38-06V1GP08DGP08DPKG23HSS83TDP6KE200AG23RD2.2M-T1BRGP02-20EL-6394
FMQ-G5GS
HSU83TRF
HZS10NB2TDHZS12NB2TDHZS13NB2TDHZS16NB2TDHZS33NB2HZS33NB2TDHZS4.7NB2HZS4.7NB2TDHZS5.1NB2TDHZS5.6NB2TDMTZJ-T-77-39BMTZJ-39BRD10ESB2RD12ES-B2RD12ES-T1B2RD13ES-B2RD20ES-B2RD20ES-T1B2RD22ES-B2RD22ES-T1B2RD5.1ESB2RD5.6ES-T1B2RD5.6ESB2RD6.8ES-B21SS119-251SS119-25TD1SS133T-77
ON3171-R
RD9.1ES-L2RD9.1ES-T1B
RM11ARM11C
SPR-325MVW
YG802C09
YG911S3R
1PS181-115
1PS226-115
1SS355TE-17
1SS376TE-17
ANODE
CATHODE
MARKING SIDE VIEW
1
110
E
LETTER SIDE
C B
E
B
C
1 TOP VIEW
n
1 TOP VIEW
n
BE
C
ECB
B C E
E C B
E C B
B
C E
G S D
D
SG
SDG
GD
S
CATHODE
ANODE
~~
+
–
~~
+
–
CATHODE
ANODE
CATHODE
ANODE
CATHODE
ANODE
CATHODE
ANODE
CATHODE
ANODE(GRN)
ANODE(RED)
CATHODE
ANODE
CATHODE
ANODE
E C B
10pin SIP
CPD-G500
• Items marked " * " are not stocked sincethey are seldom required for routineservice. Some delay should beanticipated when ordering these items.
• Items with no part number and nodescription are not stocked because theyare seldom required for routine service.
• The construction parts of an assembledpart are indicated with a collation numberin the remark column.
6-1. CHASSISr 7-685-648-79 +BVTP 3X12p 7-685-663-71 +BVTP 4X16
7-685-646-79 +BVTP 3X8¢ 7-685-881-09 +BVTT 4X8
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
6-1
SECTION 6
EXPLODED VIEWS
1 * A-1346-827-B D BOARD, COMPLETE 2[U/C, AEP, SH, EQ for Japan-made set]
1 * A-1346-860-A D BOARD, COMPLETE 2[U/C for Mexico-made set]
1 * A-1346-859-A D BOARD, COMPLETE 2[AEP for UK-made set]
2 !X-4560-175-1 TRANSFORMER ASSY, FLYBACK (NX4502//J1D4)
3 4-062-115-01 SCREW +P 3.5X20 TYPE2
4 * 4-060-359-01 HOLDER, PRINTED CIRCUIT BOARD5 * 3-701-903-11 HOLDER, PRINTED CIRCUIT BOARD6 4-070-730-01 HOLDER, PRINTED CIRCUIT BOARD7 * A-1316-443-B G BOARD, COMPLETE
[U/C, AEP, SH, EQ for Japan-made set]7 * A-1316-481-A G BOARD, COMPLETE
[U/C for Mexico-made set]
7 * A-1316-480-A G BOARD, COMPLETE[AEP for UK-made set]
8 ! 1-251-382-31 INLET, AC 3P (WITH NOISE FILTER)9 4-070-122-01 SCREW (HD15)10 1-694-569-11 TERMINAL BOARD ASSY, I/O11 * A-1298-874-D A BOARD, COMPLETE
[U/C, AEP, SH, EQ for Japan-made set]11 * A-1298-992-A A BOARD, COMPLETE
[U/C for Mexico-made set]
11 * A-1298-988-A A BOARD, COMPLETE [AEP for UK-made set]
12 1-900-246-08 CONNECTOR ASSY (F)13 1-900-246-07 CONNECTOR ASSY (F)14 * 4-069-570-01 SPACER, PRINTED CIRCUIT BOARD15 4-071-116-01 CABINET
[U/C, AEP, SH, EQ for Japan-made set]
15 4-071-493-01 CABINET [U/C for Mexico-made set]15 4-071-452-01 CABINET [AEP for UK-made set]16 * 4-063-711-01 SUPPORT, HV CABLE
p
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque !sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.
10
111
122
13
3
144
15
5
5
6
7
8
9
16
CPD-G500
60
70
51
61
71
52
62
72
53
63
73
54
64
74
55
65
75
56
66
76
57
67
58
68
59
69
6-2. PICTURE TUBEp 7-685-663-71 +BVTP 4X16¢ 7-685-881-09 +BVTT 4X8
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
6-2
51 X-4036-843-1 BEZEL ASSY 52, 53[U/C, AEP, SH, EQ for Japan-made set]
51 X-4036-928-1 BEZEL ASSY 52, 53[U/C for Mexico-made set]
51 X-4036-914-1 BEZEL ASSY 52, 53[AEP for UK-made set]
52 4-070-660-01 BUTTON, POWER[U/C, AEP, SH, EQ for Japan-made set]
52 4-071-152-01 BUTTON, POWER [U/C for Mexico-made set]
52 4-204-957-01 BUTTON, POWER [AEP for UK-made set]53 3-635-339-01 SPRING, COMPRESSION
[Except U/C for Mexico-made set]53 3-653-339-21 SPRING, COMPRESSION
[U/C for Mexico-made set]54 4-071-112-01 SELECTION, INPUT
[U/C, AEP, SH, EQ for Japan-made set]54 4-071-489-01 SELECTOR, INPUT [U/C for Mexico-made set]
54 4-071-453-01 KNOB, INPUT SELECTION[AEP for UK-made set]
55 4-070-665-01 BUTTON, MENU[U/C, AEP, SH, EQ for Japan-made set]
55 4-071-155-01 BUTTON, MENU [U/C for Mexico-made set]55 4-204-970-01 BUTTON, MENU [AEP for UK-made set]56 * A-1372-682-A H1 BOARD, COMPLETE
[U/C, AEP, SH, EQ for Japan-made set]
56 * A-1372-691-A H1 BOARD, COMPLETE[U/C for Mexico-made set]
56 * A-1372-690-A H1 BOARD, COMPLETE [AEP for UK-made set]
57 * 4-394-972-21 CAP, POWER58 X-4036-844-2 STAND ASSY 59
59 * 4-061-996-11 CUSHION60 8-738-813-61 ITC ASSY (21TKC-R1) [U/C, AEP] 61-6360 8-738-821-61 ITC ASSY (21TKC-RS1) 61-63
[SH, EQ for Japan-made set]61 8-451-509-11 DEFLECTION YOKE (Y21TKM-M)62 ! 1-452-912-61 NECK ASSEMBLY (NA-2914)
63 2-162-100-21 SPACER, DEFLECTION YOKE64 * 4-047-316-01 SPRING, EXTENSION
[Except U/C for Mexico-made set]64 * 4-061-573-01 SPRING, TENSION [U/C for Mexico-made set]65 ! 1-419-130-21 COIL, LANDING CORRECTION66 ! 1-419-128-21 COIL, DEGAUSSING
67 ! 1-419-129-21 COIL, LANDING CORRECTION68 4-062-670-01 SPACER, PICTURE TUBE69 4-365-808-01 SCREW (5), TAPPING70 4-070-730-01 HOLDER, PRINTED CIRCUIT BOARD71 * A-1394-946-C N BOARD, COMPLETE
[U/C, AEP, SH, EQ for Japan-made set]
71 * A-1394-951-A N BOARD, COMPLETE[U/C for Mexico-made set]
71 * A-1394-950-A N BOARD, COMPLETE [AEP for UK-made set]72 * A-1388-250-A J BOARD, COMPLETE
[U/C, AEP, SH, EQ for Japan-made set]72 * A-1388-261-A J BOARD, COMPLETE
[U/C for Mexico-made set]72 * A-1388-260-A J BOARD, COMPLETE [AEP for UK-made set]
73 4-308-870-00 CLIP, LEAD WIRE74 1-452-032-00 MAGNET, DISK; 10mm ø75 1-452-094-00 MAGNET, ROTATABLE DISK; 15mm ø76 4-051-736-21 PIECE A(90), CONV. CORRECT
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque !sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.
CPD-G500
103104
102
101
106 107
105
108 109
6-3. PACKING MATERIALS
REF.NO. PART NO. DESCRIPTION REMARKREF.NO. PART NO. DESCRIPTION REMARK
6-3
101 * 4-071-736-01 INDIVIDUAL CARTON[U/C, SH, EQ for Japan-made set]
101 * 4-071-779-01 INDIVIDUAL CARTON[AEP for UK-made set]
101 * 4-072-126-01 INDIVIDUAL CARTON[AEP for Japan-made set]
101 * 4-072-874-01 INDIVIDUAL CARTON[U/C for Mexico-made set]
102 * 4-071-731-01 CUSHION (LOWER) (ASSY)[U/C, AEP, SH, EQ for Japan-made set]
102 * 4-071-781-01 CUSHION (LOWER) (ASSY)[AEP for UK-made set]
102 * 4-072-876-01 CUSHION (LOWER) (ASSY)[U/C for Mexico-made set]
103 * 4-071-730-01 CUSHION (UPPER) (ASSY)[U/C, AEP, SH, EQ for Japan-made set]
103 * 4-071-780-01 CUSHION (UPPER) (ASSY)[AEP for UK-made set]
103 * 4-072-875-01 CUSHION (UPPER) (ASSY)[U/C for Mexico-made set]
104 * 4-041-927-31 BAG, POLYETHYLENE[U/C, AEP, SH, EQ for Japan-made set]
104 * 4-368-079-01 BAG, POLYETHYLENE [AEP for UK-made set]
104 * 4-047-293-01 BAG, POLYETHYLENE[U/C for Mexico-made set]
105 1-793-504-11 CABLE ASSY(15P DSUBX2 CONNECTOR)
106 3-867-232-12 MANUAL, INSTRUCTION[U/C, SH, EQ for Japan-made set]
106 3-867-232-21 MANUAL, INSTRUCTION [AEP for Japan-made set]
106 3-867-232-31 MANUAL, INSTRUCTION [U/C for Mexico-made set]
106 3-867-232-41 MANUAL, INSTRUCTION [AEP for UK-made set]
107 1-772-380-11 DISK, INFORMATION108 ! 1-785-429-11 ADAPTOR, CONVERSION for Macintosh
[Except AEP]108 1-785-512-31 CONNECTOR, D SUB (15P CHANGER)
for Macintosh new G3 [AEP]109 ! 1-782-783-31 CORD SET POWER [U/C]
109 ! 1-782-784-21 CORD SET POWER [AEP, EQ]109 ! 1-782-785-11 CORD, AC POWER
[SH for Japan-made set]
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque !sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-1
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
NOTE:
When indicating parts by referencenumber, please include the board name.
REF.NO. PART NO. DESCRIPTION REMARK
SECTION 7
ELECTRICAL PARTS LIST
REF.NO. PART NO. DESCRIPTION REMARK
The components identified by [ in thismanual have been carefully factory-selected for each set in order to satisfyregulations regarding X-ray radiation.Should replacement be required, replaceonly with the value originally used.
• All variable and adjustable resistors havecharacteristic curve B, unless otherwisenoted.
* A-1298-874-D A BOARD, COMPLETE[U/C, AEP, SH, EQ for Japan-made set]
* A-1298-992-A A BOARD, COMPLETE[U/C for Mexico-made set]
* A-1298-988-A A BOARD, COMPLETE[AEP for UK-made set]
***************************
7-682-950-01 SCREW +PSW 3X12 (IC403)
<CAPACITOR>
C101 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC102 1-104-664-11 ELECT 47µF 20% 25VC103 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC104 1-104-664-11 ELECT 47µF 20% 25VC107 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
C108 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC109 1-163-229-11 CERAMIC CHIP12pF 5% 50VC110 1-163-275-11 CERAMIC CHIP0.001µF 5% 50VC112 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC113 1-164-489-11 CERAMIC CHIP0.22µF 10% 16V
C114 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC115 1-104-341-11 FILM 0.1µF 10% 250VC120 1-104-341-11 FILM 0.1µF 10% 250VC201 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC202 1-104-664-11 ELECT 47µF 20% 25V
C203 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC204 1-104-664-11 ELECT 47µF 20% 25VC205 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC206 1-109-982-11 CERAMIC CHIP1µF 10% 10VC207 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
C208 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC209 1-163-227-11 CERAMIC CHIP10pF 0.5pF 50VC210 1-163-275-11 CERAMIC CHIP0.001µF 5% 50VC212 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC213 1-164-489-11 CERAMIC CHIP0.22µF 10% 16V
C214 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC215 1-104-341-11 FILM 0.1µF 10% 250VC216 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC220 1-104-341-11 FILM 0.1µF 10% 250VC301 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C302 1-104-664-11 ELECT 47µF 20% 25VC303 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C304 1-104-664-11 ELECT 47µF 20% 25VC307 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC308 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
C309 1-163-227-11 CERAMIC CHIP10pF 0.5pF 50VC310 1-163-275-11 CERAMIC CHIP0.001µF 5% 50VC312 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC313 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC314 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
C315 1-104-341-11 FILM 0.1µF 10% 250VC320 1-104-341-11 FILM 0.1µF 10% 250VC401 1-126-964-11 ELECT 10µF 20% 50VC402 1-104-664-11 ELECT 47µF 20% 25VC403 1-163-259-91 CERAMIC CHIP220pF 5% 50V
C404 1-163-259-91 CERAMIC CHIP220pF 5% 50VC405 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC406 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC407 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC408 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C410 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC411 1-104-664-11 ELECT 47µF 20% 25VC413 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC415 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC416 1-126-961-11 ELECT 2.2µF 20% 50V
C417 1-104-574-11 CERAMIC 0.0047µF 10% 2KVC419 1-162-318-11 CERAMIC 0.001µF 10% 500VC420 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC421 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC422 1-164-489-11 CERAMIC CHIP0.22µF 10% 16V
C423 1-104-664-11 ELECT 47µF 20% 25VC424 1-162-318-11 CERAMIC 0.001µF 10% 500VC425 1-163-251-11 CERAMIC CHIP100pF 5% 50VC426 1-163-251-11 CERAMIC CHIP100pF 5% 50VC427 1-163-235-11 CERAMIC CHIP22pF 5% 50V
C430 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC431 1-163-275-11 CERAMIC CHIP0.001µF 5% 50VC432 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC433 1-162-318-11 CERAMIC 0.001µF 10% 500VC434 1-162-318-11 CERAMIC 0.001µF 10% 500V
C435 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC436 1-164-489-11 CERAMIC CHIP0.22µF 10% 16VC437 1-126-934-11 ELECT 220µF 20% 16VC438 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC440 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
A• Items marked " * " are not stocked since
they are seldom required for routineservice. Some delay should be anticipatedwhen ordering these items.
RESISTORS• All resistors are in ohms• F : nonflammable
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-2
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
C441 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC442 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC443 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC444 1-162-318-11 CERAMIC 0.001µF 10% 500VC446 1-104-664-11 ELECT 47µF 20% 25V
C449 1-109-982-11 CERAMIC CHIP1µF 10% 10VC450 1-107-823-11 CERAMIC CHIP0.47µF 10% 16VC456 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC457 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC458 1-115-339-11 CERAMIC CHIP0.1µF 10% 50V
C459 1-128-560-11 ELECT 22µF 20% 100VC462 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC463 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC464 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC467 1-107-957-11 ELECT 1µF 20% 250V
<CONNECTOR>
CN401 1-793-183-11 CONNECTOR, D SUB 15PCN402*1-564-509-11 PLUG, CONNECTOR 6PCN403 1-784-463-11 CONNECTOR, FFC/FPC 21PCN405*1-564-524-11 PLUG, CONNECTOR 9PCN406*1-766-179-11 PIN, CONNECTOR (PC BOARD) 2P
<DIODE>
D101 8-719-062-51 DIODE 1PS226-115D102 8-719-062-51 DIODE 1PS226-115D103 8-719-066-10 DIODE 1PS181-115D105 8-719-051-85 DIODE HSS83TDD106 8-719-052-12 DIODE 1SS376TE-17
D107 8-719-052-12 DIODE 1SS376TE-17D201 8-719-062-51 DIODE 1PS226-115D202 8-719-062-51 DIODE 1PS226-115D203 8-719-066-10 DIODE 1PS181-115D205 8-719-051-85 DIODE HSS83TD
D206 8-719-052-12 DIODE 1SS376TE-17D207 8-719-052-12 DIODE 1SS376TE-17D301 8-719-062-51 DIODE 1PS226-115D302 8-719-062-51 DIODE 1PS226-115D303 8-719-066-10 DIODE 1PS181-115
D305 8-719-051-85 DIODE HSS83TDD306 8-719-052-12 DIODE 1SS376TE-17D307 8-719-052-12 DIODE 1SS376TE-17D402 8-719-801-78 DIODE 1SS184D403 8-719-982-36 ZENER DIODE MTZJ-39B
D405 8-719-911-19 DIODE 1SS119-25D406 8-719-062-51 DIODE 1PS226-115D407 8-719-062-51 DIODE 1PS226-115
<FERRITE BEAD>
FB102 1-500-419-22 FERRITEFB202 1-500-419-22 FERRITEFB302 1-500-419-22 FERRITEFB402 1-412-911-11 FERRITE 1.1µHFB403 1-412-911-11 FERRITE 1.1µH
FB404 1-412-911-11 FERRITE 1.1µHFB405 1-412-911-11 FERRITE 1.1µHFB406 1-412-911-11 FERRITE 1.1µHFB411 1-412-911-11 FERRITE 1.1µH
<IC>
IC401 8-759-584-87 IC M52757FP-TPIC402 8-759-584-86 IC M52749FP-TPIC403 8-749-015-91 IC FA4301IC404 8-759-585-72 IC CXD9514MIC405 8-759-701-01 IC NJM2904M
IC406 8-749-015-92 IC H8D2972IC407 8-759-925-74 IC SN74HC04ANS
<COIL>
L402 1-412-529-11 INDUCTOR 22µHL403 1-412-537-31 INDUCTOR 100µHL404 1-414-940-21 INDUCTOR 100µHL405 1-412-529-11 INDUCTOR 22µH
<IC LINK>
PS401!1-533-590-31LINK, IC (1A/90V AC, 60V DC)
<TRANSISTOR>
Q101 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q201 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q301 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q401 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q402 8-729-050-41 TRANSISTOR 2SJ360TE12L
Q406 8-729-216-22 TRANSISTOR 2SA1162-GQ407 8-729-028-74 TRANSISTOR DTA114TUA-T106Q410 8-729-032-61 TRANSISTOR 2SC5022-02
<RESISTOR>
R101 1-215-394-00 METAL 75 1% 1/4WR103 1-215-394-00 METAL 75 1% 1/4WR105 1-216-017-91 RES,CHIP 47 5% 1/10WR106 1-216-017-91 RES,CHIP 47 5% 1/10WR107 1-216-045-00 RES,CHIP 680 5% 1/10W
R109 1-216-075-00 RES,CHIP 12K 5% 1/10WR110 1-216-097-91 RES,CHIP 100K 5% 1/10WR111 1-216-041-00 RES,CHIP 470 5% 1/10WR112 1-216-009-91 RES,CHIP 22 5% 1/10WR113 1-216-017-91 RES,CHIP 47 5% 1/10W
R114 1-216-009-91 RES,CHIP 22 5% 1/10WR115 1-219-742-11 CARBON 47 5% 1/2WR116 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR117 1-216-121-91 RES,CHIP 1M 5% 1/10WR118 1-216-121-91 RES,CHIP 1M 5% 1/10W
R119 1-216-077-91 RES,CHIP 15K 5% 1/10WR120 1-216-113-00 RES,CHIP 470K 5% 1/10WR121 1-216-113-00 RES,CHIP 470K 5% 1/10WR122 1-216-081-00 RES,CHIP 22K 5% 1/10W
A
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-3
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
R128 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R130 1-216-113-00 RES,CHIP 470K 5% 1/10WR137 1-249-413-11 CARBON 470 5% 1/4WR138 1-216-017-91 RES,CHIP 47 5% 1/10WR161 1-216-041-00 RES,CHIP 470 5% 1/10WR201 1-215-394-00 METAL 75 1% 1/4W
R202 1-216-097-91 RES,CHIP 100K 5% 1/10WR203 1-215-394-00 METAL 75 1% 1/4WR205 1-216-017-91 RES,CHIP 47 5% 1/10WR206 1-216-017-91 RES,CHIP 47 5% 1/10WR207 1-216-045-00 RES,CHIP 680 5% 1/10W
R209 1-216-075-00 RES,CHIP 12K 5% 1/10WR210 1-216-097-91 RES,CHIP 100K 5% 1/10WR211 1-216-033-00 RES,CHIP 220 5% 1/10WR212 1-216-009-91 RES,CHIP 22 5% 1/10WR213 1-216-017-91 RES,CHIP 47 5% 1/10W
R214 1-216-009-91 RES,CHIP 22 5% 1/10WR215 1-219-742-11 CARBON 47 5% 1/2WR216 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR217 1-216-121-91 RES,CHIP 1M 5% 1/10WR218 1-216-121-91 RES,CHIP 1M 5% 1/10W
R219 1-216-077-91 RES,CHIP 15K 5% 1/10WR220 1-216-113-00 RES,CHIP 470K 5% 1/10WR221 1-216-113-00 RES,CHIP 470K 5% 1/10WR222 1-216-081-00 RES,CHIP 22K 5% 1/10WR228 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R230 1-216-113-00 RES,CHIP 470K 5% 1/10WR237 1-249-413-11 CARBON 470 5% 1/4WR238 1-216-017-91 RES,CHIP 47 5% 1/10WR261 1-216-041-00 RES,CHIP 470 5% 1/10WR301 1-215-394-00 METAL 75 1% 1/4W
R303 1-215-394-00 METAL 75 1% 1/4WR305 1-216-017-91 RES,CHIP 47 5% 1/10WR306 1-216-017-91 RES,CHIP 47 5% 1/10WR307 1-216-045-00 RES,CHIP 680 5% 1/10WR309 1-216-075-00 RES,CHIP 12K 5% 1/10W
R310 1-216-097-91 RES,CHIP 100K 5% 1/10WR311 1-216-033-00 RES,CHIP 220 5% 1/10WR312 1-216-009-91 RES,CHIP 22 5% 1/10WR313 1-216-017-91 RES,CHIP 47 5% 1/10WR314 1-216-009-91 RES,CHIP 22 5% 1/10W
R315 1-219-742-11 CARBON 47 5% 1/2WR316 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR317 1-216-121-91 RES,CHIP 1M 5% 1/10WR318 1-216-121-91 RES,CHIP 1M 5% 1/10WR319 1-216-077-91 RES,CHIP 15K 5% 1/10W
R320 1-216-113-00 RES,CHIP 470K 5% 1/10WR321 1-216-113-00 RES,CHIP 470K 5% 1/10WR322 1-216-081-00 RES,CHIP 22K 5% 1/10WR328 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR330 1-216-113-00 RES,CHIP 470K 5% 1/10W
R337 1-249-413-11 CARBON 470 5% 1/4WR338 1-216-017-91 RES,CHIP 47 5% 1/10WR361 1-216-041-00 RES,CHIP 470 5% 1/10WR402 1-216-049-91 RES,CHIP 1K 5% 1/10WR403 1-216-081-00 RES,CHIP 22K 5% 1/10W
R404 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR405 1-216-049-91 RES,CHIP 1K 5% 1/10WR406 1-216-097-91 RES,CHIP 100K 5% 1/10WR407 1-218-768-11 METAL CHIP 470K 0.50%1/10WR409 1-216-129-00 RES,CHIP 2.2M 5% 1/10W
R411 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR412 1-216-105-91 RES,CHIP 220K 5% 1/10WR413 1-216-097-91 RES,CHIP 100K 5% 1/10WR414 1-216-089-91 RES,CHIP 47K 5% 1/10WR415 1-216-097-91 RES,CHIP 100K 5% 1/10W
R417 1-216-121-91 RES,CHIP 1M 5% 1/10WR418 1-260-127-11 CARBON 220K 5% 1/2WR419 1-216-033-00 RES,CHIP 220 5% 1/10WR420 1-216-025-91 RES,CHIP 100 5% 1/10WR421 1-216-025-91 RES,CHIP 100 5% 1/10W
R422 1-216-025-91 RES,CHIP 100 5% 1/10WR424 1-216-049-91 RES,CHIP 1K 5% 1/10WR425 1-216-049-91 RES,CHIP 1K 5% 1/10WR426 1-216-105-91 RES,CHIP 220K 5% 1/10WR427 1-216-049-91 RES,CHIP 1K 5% 1/10W
R428 1-216-025-91 RES,CHIP 100 5% 1/10WR430 1-216-025-91 RES,CHIP 100 5% 1/10WR431 1-216-113-00 RES,CHIP 470K 5% 1/10WR436 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR438 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R439 1-216-041-00 RES,CHIP 470 5% 1/10WR441 1-216-121-91 RES,CHIP 1M 5% 1/10WR442 1-216-049-91 RES,CHIP 1K 5% 1/10WR443 1-216-025-91 RES,CHIP 100 5% 1/10WR444 1-216-025-91 RES,CHIP 100 5% 1/10W
R445 1-216-025-91 RES,CHIP 100 5% 1/10WR446 1-216-025-91 RES,CHIP 100 5% 1/10WR447 1-216-017-91 RES,CHIP 47 5% 1/10WR448 1-216-017-91 RES,CHIP 47 5% 1/10WR449 1-216-081-00 RES,CHIP 22K 5% 1/10W
R450 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR451 1-216-129-00 RES,CHIP 2.2M 5% 1/10WR453 1-216-073-00 RES,CHIP 10K 5% 1/10WR454 1-216-129-00 RES,CHIP 2.2M 5% 1/10WR455 1-216-097-91 RES,CHIP 100K 5% 1/10W
R456 1-216-025-91 RES,CHIP 100 5% 1/10WR457 1-211-895-11 METAL 10M 10% 1/4WR458 1-211-885-21 METAL 2.2M 5% 1WR459 1-211-895-11 METAL 10M 10% 1/4WR460 1-216-073-00 RES,CHIP 10K 5% 1/10W
R463 1-216-097-91 RES,CHIP 100K 5% 1/10WR464 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR488 1-216-089-91 RES,CHIP 47K 5% 1/10WR490 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR491 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
<SPARK GAP>
SG101 1-576-354-21 GAP, SPARKSG201 1-576-354-21 GAP, SPARKSG301 1-576-354-21 GAP, SPARKSG401 1-576-354-21 GAP, SPARK
A
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-4
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
SG402 1-519-422-11 GAP, SPARK
<SOCKET>
SK401!1-451-499-11SOCKET, PICTURE TUBE
<CRYSTAL>
X401 1-781-472-21 VIBRATOR, CERAMIC (8MHz)
****************************************************************************
* A-1316-443-B G BOARD, COMPLETE[U/C, AEP, SH, EQ for Japan-made set]
* A-1316-481-A G BOARD, COMPLETE[U/C for Mexico-made set]
* A-1316-480-A G BOARD, COMPLETE[AEP for UK-made set]
***************************
1-533-223-11 HOLDER, FUSE (F601)4-382-854-11 SCREW (M3X10), P, SW (+)
(D610,D652,D680,IC610,IC654,Q603,Q630)
<CAPACITOR>
C601! 1-113-513-11 FILM 1µF 20% 275VC602! 1-113-513-11 FILM 1µF 20% 275VC603! 1-113-900-51 CERAMIC 470pF 10% 250VC604! 1-113-900-51 CERAMIC 470pF 10% 250VC605! 1-113-926-91 CERAMIC 0.0047µF 250V
C606! 1-113-926-91 CERAMIC 0.0047µF 250VC607 1-113-900-11 CERAMIC 470pF 10% 250VC610 1-117-849-11 ELECT 330µF 20% 450VC611 1-137-479-11 FILM 1µF 10% 400VC612 1-136-169-00 FILM 0.22µF 5% 50V
C613 1-126-967-11 ELECT 47µF 20% 50VC614 1-163-251-11 CERAMIC CHIP100pF 5% 50VC620 1-128-990-11 FILM 27000pF 5% 800VC621 1-104-330-91 CERAMIC 470pF 10% 1KVC622 1-104-330-91 CERAMIC 470pF 10% 1KV
C623 1-136-171-00 FILM 0.33µF 5% 50VC624 1-136-171-00 FILM 0.33µF 5% 50VC625 1-136-167-00 FILM 0.15µF 5% 50VC626 1-136-167-00 FILM 0.15µF 5% 50VC627 1-104-330-91 CERAMIC 470pF 10% 1KV
C629 1-137-370-11 FILM 0.01µF 5% 50VC630 1-163-005-11 CERAMIC CHIP470pF 10% 50VC631 1-104-665-11 ELECT 100µF 20% 25VC633 1-164-161-11 CERAMIC CHIP0.0022µF 10% 50VC634 1-163-009-11 CERAMIC CHIP0.001µF 10% 50V
C650 1-107-656-11 ELECT 100µF 20% 250VC651 1-107-651-11 ELECT 4.7µF 20% 250VC652 1-128-563-11 ELECT 100µF 20% 100VC653 1-128-581-11 ELECT 4.7µF 20% 100VC654 1-126-943-11 ELECT 2200µF 20% 25V
C655 1-104-664-11 ELECT 47µF 20% 25VC656 1-126-943-11 ELECT 2200µF 20% 25VC657 1-104-664-11 ELECT 47µF 20% 25VC658 1-126-927-11 ELECT 2200µF 20% 10VC659 1-128-339-11 ELECT 2200µF 20% 10V
C660 1-126-967-11 ELECT 47µF 20% 50VC661 1-107-429-11 CERAMIC 0.0022µF 10% 1KVC662 1-137-370-11 FILM 0.01µF 5% 50VC663 1-126-961-11 ELECT 2.2µF 20% 50VC665 1-107-909-11 ELECT 47µF 20% 10V
C666 1-126-964-11 ELECT 10µF 20% 50VC667 1-107-909-11 ELECT 47µF 20% 16VC680 1-115-747-51 ELECT 0.0068F 20% 10VC681 1-104-664-11 ELECT 47µF 20% 10VC682 1-137-368-11 FILM 0.0047µF 5% 50V
C683 1-104-664-11 ELECT 47µF 20% 10VC684 1-107-909-11 ELECT 47µF 20% 10VC685 1-128-526-11 ELECT 100µF 20% 10VC686 1-104-664-11 ELECT 47µF 20% 10VC687 1-126-964-11 ELECT 10µF 20% 50V
C692 1-115-339-11 CERAMIC CHIP0.1µF 10% 50V
<CONNECTOR>
CN601*1-580-689-11 PIN, CONNECTOR (PC BOARD) 4PCN602*1-691-960-11 PIN, CONNECTOR (PC BOARD) 3PCN603*1-691-960-11 PIN, CONNECTOR (PC BOARD) 3PCN650*1-564-510-11 PLUG, CONNECTOR 7PCN652*1-564-512-11 PLUG, CONNECTOR 9P
CN653*1-564-509-11 PLUG, CONNECTOR 6PCN654*1-564-511-11 PLUG, CONNECTOR 8P
<DIODE>
D610! 8-719-510-53 DIODE D4SB60LD612 8-719-911-19 DIODE 1SS119-25D613 8-719-304-63 DIODE RM11CD620 8-719-911-19 DIODE 1SS119-25D631 8-719-063-73 DIODE D1NL20U-TR
D632 8-719-059-23 DIODE P6KE200AG23D633 8-719-069-63 DIODE ERB38-06V1D634 8-719-911-19 DIODE 1SS119-25D635 8-719-110-53 ZENER DIODE RD20ESB2D637 8-719-911-19 DIODE 1SS119-25
D650 8-719-064-49 DIODE D4SBL40D651 8-719-063-73 DIODE D1NL20U-TRD652 8-719-052-91 DIODE D4SBS4-FD653 8-719-022-97 DIODE D2S4MFD654 8-719-022-97 DIODE D2S4MF
D655 8-719-063-73 DIODE D1NL20U-TRD656 8-719-911-19 DIODE 1SS119-25D660 8-719-110-57 ZENER DIODE RD22ESB2D661 8-719-110-31 ZENER DIODE RD12ESB2D663 8-719-911-19 DIODE 1SS119-25
D664 8-719-110-57 ZENER DIODE RD22ESB2D665 8-719-911-19 DIODE 1SS119-25
AG
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-5
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
D666 8-719-911-19 DIODE 1SS119-25D680 8-719-989-87 DIODE YG802C09D681 8-719-109-89 ZENER DIODE RD5.6ESB2
D682 8-719-121-26 ZENER DIODE RD9.1ESL2D683 8-719-911-19 DIODE 1SS119-25D690 8-719-911-19 DIODE 1SS119-25D692 8-719-911-19 DIODE 1SS119-25
<FUSE>
F601! 1-576-233-11 FUSE (H.B.C.) (6.3A/250V)
<FERRITE BEAD>
FB630 1-410-396-41 FERRITE 0.45µHFB632!1-410-397-31 FERRITE 1.1µH
<IC>
IC610 8-749-015-89 IC MZ1530IC630 8-759-535-32 IC FA13842PIC650 8-749-012-49 IC DM-57NIC651 8-759-592-79 IC BA00AST-V5IC652 8-759-496-15 IC BA05ST-V5
IC653 8-759-450-47 IC BA05TIC654 8-759-643-66 IC µPC2912HF(12)IC680 8-759-321-95 IC HA17431PA
<COIL>
L610 1-419-126-21 COIL, CHOKE (AFC) 216µHL611 1-411-674-11 INDUCTOR 68µHL650 1-414-742-21 INDUCTOR 22µHL651 1-414-742-21 INDUCTOR 22µHL652 1-412-529-11 INDUCTOR 22µH
L653 1-412-529-11 INDUCTOR 22µHL680 1-414-742-21 INDUCTOR 22µH
<PHOTO COUPLER>
PH620 8-749-924-35 PHOTO COUPLER ON3171-RPH630 8-749-924-35 PHOTO COUPLER ON3171-R
<IC LINK>
PS650!1-533-593-31LINK, IC (2A/90V AC, 60V DC)
<TRANSISTOR>
Q603 8-729-045-39 TRANSISTOR MX0842AB-FQ610 8-729-119-76 TRANSISTOR 2SA1175-HFEQ621 8-729-119-78 TRANSISTOR 2SC2785-HFEQ630 8-729-045-03 TRANSISTOR 2SK2647-01MR-F91Q631 8-729-041-66 TRANSISTOR 2SC4015TV2
Q632 8-729-041-66 TRANSISTOR 2SC4015TV2Q633 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q650 8-729-119-76 TRANSISTOR 2SA1175-HFEQ651 8-729-230-45 TRANSISTOR 2SC2458-YGRQ652 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q653 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q654 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ667 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ670 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ671 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R
Q691 8-729-119-78 TRANSISTOR 2SC2785-HFE
<RESISTOR>
R601! 1-220-825-91 CARBON 330K 5% 1/2WR602 1-216-465-11 METAL OXIDE 27K 5% 2W FR603 1-247-895-91 CARBON 470K 5% 1/4WR604 1-216-113-00 RES,CHIP 470K 5% 1/10WR605 1-216-113-00 RES,CHIP 470K 5% 1/10W
R606 1-216-097-91 RES,CHIP 100K 5% 1/10WR607 1-216-097-91 RES,CHIP 100K 5% 1/10WR608 1-216-073-00 RES,CHIP 10K 5% 1/10WR609 1-216-069-00 RES,CHIP 6.8K 5% 1/10WR610 1-217-152-00 METAL 0.33 10% 2W
R611 1-217-153-00 METAL 0.47 10% 2WR612 1-249-425-11 CARBON 4.7K 5% 1/4WR613 1-216-089-91 RES,CHIP 47K 5% 1/10WR614 1-247-807-31 CARBON 100 5% 1/4WR615 1-249-427-11 CARBON 6.8K 5% 1/4W
R616 1-216-671-11 METAL CHIP 6.8K 0.50%1/10WR617 1-249-417-11 CARBON 1K 5% 1/4WR618 1-216-369-00 METAL OXIDE 1 5% 2W FR620 1-202-933-61 FUSIBLE 0.1 10% 1/2W FR621 1-249-432-11 CARBON 18K 5% 1/4W
R622 1-216-089-91 RES,CHIP 47K 5% 1/10WR623 1-218-642-11 METAL OXIDE 100K 5% 1W FR624 1-218-642-11 METAL OXIDE 100K 5% 1W FR625 1-216-349-00 METAL OXIDE 1 5% 1W FR626 1-216-349-00 METAL OXIDE 1 5% 1W F
R627 1-216-683-11 METAL CHIP 22K 0.50%1/10WR628 1-216-695-11 METAL CHIP 68K 0.50%1/10WR629 1-216-683-11 METAL CHIP 22K 0.50%1/10WR630 1-249-387-11 CARBON 3.3 5% 1/4W FR632 1-215-399-00 METAL 120 1% 1/4W
R633 1-260-135-11 CARBON 1M 5% 1/2WR634 1-260-135-11 CARBON 1M 5% 1/2WR635 1-216-465-11 METAL OXIDE 27K 5% 2W FR636 1-247-863-91 CARBON 22K 5% 1/4WR637 1-219-134-11 FUSIBLE 0.1 10% 1/4W
R638 1-219-134-11 FUSIBLE 0.1 10% 1/4WR649 1-249-437-11 CARBON 47K 5% 1/4W FR650 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR652 1-216-113-00 RES,CHIP 470K 5% 1/10WR653 1-249-413-11 CARBON 470 5% 1/4W
R654 1-211-796-11 FUSIBLE 1 5% 1/2W FR655 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR656 1-260-292-11 CARBON 1 5% 1/2WR657 1-249-443-11 CARBON 0.47 5% 1/4W F
G
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-6
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
R658 1-216-073-00 RES,CHIP 10K 5% 1/10W
R659 1-216-049-91 RES,CHIP 1K 5% 1/10WR661 1-247-807-31 CARBON 100 5% 1/4WR662 1-216-073-00 RES,CHIP 10K 5% 1/10WR663 1-216-073-00 RES,CHIP 10K 5% 1/10WR664 1-216-073-00 RES,CHIP 10K 5% 1/10W
R665 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR666 1-216-073-00 RES,CHIP 10K 5% 1/10WR667 1-216-089-91 RES,CHIP 47K 5% 1/10WR668 1-215-457-00 METAL 33K 1% 1/4WR670 1-216-677-11 METAL CHIP 12K 0.50%1/10W
R671 1-216-677-11 METAL CHIP 12K 0.50%1/10WR672 1-216-664-11 METAL CHIP 3.6K 0.50%1/10WR673 1-216-073-00 RES,CHIP 10K 5% 1/10WR674 1-216-097-91 RES,CHIP 100K 5% 1/10WR675 1-216-668-11 METAL CHIP 5.1K 0.50%1/10W
R676 1-216-663-11 METAL CHIP 3.3K 0.50%1/10WR677 1-216-661-11 METAL CHIP 2.7K 0.50%1/10WR678 1-216-391-11 METAL OXIDE 1.5 5% 3W FR680 1-215-475-00 METAL 180K 1% 1/4WR681 1-216-073-00 RES,CHIP 10K 5% 1/10W
R682 1-216-049-91 RES,CHIP 1K 5% 1/10WR683 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR684 1-216-073-00 RES,CHIP 10K 5% 1/10WR685 1-216-049-91 RES,CHIP 1K 5% 1/10WR686 1-216-033-00 RES,CHIP 220 5% 1/10W
R687 1-216-081-00 RES,CHIP 22K 5% 1/10WR688 1-215-473-00 METAL 150K 1% 1/4WR693 1-260-085-11 CARBON 68 5% 1/2WR694 1-216-073-00 RES,CHIP 10K 5% 1/10WR695 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R696 1-249-407-11 CARBON 150 5% 1/4W
<RELAY>
RY602!1-755-318-11RELAY, POWERRY603!1-755-067-21RELAY
<SPARK GAP>
SG601!1-533-982-11GAP, SPARK
<TRANSFORMER>
T601! 1-429-180-11 TRANSFORMER, LINE FILTERT620 1-433-894-11 TRANSFORMER, CONVERTER (PIT)T621 1-429-992-11 TRANSFORMER, CONVERTER (PRT)T630 1-433-895-31 TRANSFORMER, CONVERTER (SRT)
<THERMISTOR>
TH601!1-809-260-11THERMISTOR, POWERTHP601!1-809-827-31THERMISTOR, POSITIVE
<VARISTOR>
VDR601!1-801-268-51VARISTOR TNR14V471K660VDR602!1-810-622-11VARISTOR
***************************************************************************
* A-1346-827-B D BOARD, COMPLETE[U/C, AEP, SH, EQ for Japan-made set]
* A-1346-860-A D BOARD, COMPLETE[U/C for Mexico-made set]
* A-1346-859-A D BOARD, COMPLETE[AEP for UK-made set]
***************************
3-710-578-01 COVER, VOLUME, 6 MOLD (RV901)4-070-828-01 INSULATING SHEET (Q515)4-070-829-02 INSULATING SHEET (IC502)4-070-830-01 INSULATING SHEET (IC701)4-382-854-11 SCREW (M3X10), P, SW (+)
(IC701,Q704,Q705,Q905,Q906,R918)
7-685-647-79 SCREW +BVTP 3X10 TYPE2 TT(B)(D511,IC502,Q508,Q515,R547)
<CAPACITOR>
C501 1-126-964-11 ELECT 10µF 20% 50VC502 1-136-169-00 FILM 0.22µF 5% 50VC503 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC504 1-163-017-00 CERAMIC CHIP0.0047µF 10% 50VC505 1-126-964-11 ELECT 10µF 20% 50V
C506 1-137-194-81 FILM 0.47µF 5% 50VC507 1-136-169-00 FILM 0.22µF 5% 50VC508 1-126-965-11 ELECT 22µF 20% 50VC509 1-115-521-11 FILM 0.82µF 5% 250VC510 1-117-398-11 ELECT 33µF 20% 250V
C511 1-163-113-00 CERAMIC CHIP68pF 5% 50VC512 1-163-251-11 CERAMIC CHIP100pF 5% 50VC513 1-163-017-00 CERAMIC CHIP0.0047µF 10% 50VC514 1-106-375-12 MYLAR 0.022µF 99% 200VC515 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C516 1-126-935-11 ELECT 470µF 20% 16VC517 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC518 1-137-194-81 FILM 0.47µF 5% 50VC519 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC520 1-107-914-11 ELECT 1000µF 20% 25V
C521 1-117-666-71 FILM 0.39µF 5% 250VC522 1-137-368-11 FILM 0.0047µF 5% 50VC523 1-137-368-11 FILM 0.0047µF 5% 50VC524 1-163-133-00 CERAMIC CHIP470pF 5% 50VC525 1-104-760-11 CERAMIC CHIP0.047µF 10% 50V
C526 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC527 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC528 1-115-514-11 FILM 0.22µF 5% 250VC529 1-104-665-11 ELECT 100µF 20% 25VC530 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C531 1-107-846-11 FILM 0.1µF 5% 250V
GD
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-7
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
C532 1-163-009-11 CERAMIC CHIP0.001µF 10% 50VC533 1-107-889-11 ELECT 220µF 20% 25VC534 1-107-889-11 ELECT 220µF 20% 25VC535 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C536 1-126-967-11 ELECT 47µF 20% 50VC537 1-113-694-11 FILM 0.056µF 5% 400VC538 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC539 1-163-017-00 CERAMIC CHIP0.0047µF 10% 50VC540 1-106-343-00 MYLAR 0.001µF 10% 200V
C541 1-164-161-11 CERAMIC CHIP0.0022µF 10% 50VC542 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC543 1-125-924-11 FILM 3900pF 3% 1.8KVC544 1-125-925-11 FILM MELF 0.027µF 5% 400VC545 1-107-597-11 CERAMIC 22pF 5% 500V
C546 1-107-444-11 CERAMIC 100pF 5% 2KVC547 1-130-061-91 FILM 0.0015µF 5% 630VC548 1-162-134-11 CERAMIC 470pF 10% 2KVC549 1-130-495-00 FILM 0.1µF 5% 50VC550 1-127-833-11 FILM 0.15µF 5% 400V
C551 1-163-017-00 CERAMIC CHIP0.0047µF 10% 50VC552 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC554 1-107-444-11 CERAMIC 100pF 5% 2KVC555 1-107-683-11 ELECT 2.2µF 0 250VC556 1-115-356-11 FILM 1.2µF 5% 250V
C557 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC558 1-104-665-11 ELECT 100µF 20% 25VC559 1-107-649-11 ELECT 2.2µF 20% 250VC560 1-126-965-11 ELECT 22µF 20% 50VC561 1-104-664-11 ELECT 47µF 20% 25V
C562 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC563 1-137-365-11 FILM 0.0015µF 5% 50VC564 1-126-960-11 ELECT 1µF 20% 50VC565 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC566 1-137-370-11 FILM 0.01µF 5% 50V
C567 1-164-161-11 CERAMIC CHIP0.0022µF 10% 50VC568 1-104-760-11 CERAMIC CHIP0.047µF 10% 50VC571 1-163-227-11 CERAMIC CHIP10pF 0.5pF 50VC572 1-163-009-11 CERAMIC CHIP0.001µF 10% 50VC573 1-106-375-12 MYLAR 0.022µF 99% 200V
C574 1-163-017-00 CERAMIC CHIP0.0047µF 10% 50VC575 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC577 1-126-964-11 ELECT 10µF 20% 50VC701 1-128-560-11 ELECT 22µF 20% 100VC702 1-128-562-11 ELECT 47µF 20% 100V
C703 1-107-427-91 CERAMIC 0.001µF 10% 1KVC704 1-104-568-11 CERAMIC 470pF 10% 2KVC706 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC707 1-130-495-00 FILM 0.1µF 5% 50VC708 1-126-942-61 ELECT 1000µF 20% 25V
C709 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC710 1-107-894-11 ELECT 220µF 20% 35VC711 1-163-019-00 CERAMIC CHIP0.0068µF 10% 50VC712 1-106-228-00 MYLAR 0.22µF 10% 100VC713 1-126-942-61 ELECT 1000µF 20% 25V
C715 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC720 1-126-964-11 ELECT 10µF 20% 50V
C901 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC902 1-104-665-11 ELECT 100µF 20% 25VC903 1-126-964-11 ELECT 10µF 20% 50V
C905 1-163-127-00 CERAMIC CHIP270pF 5% 50VC907 1-163-257-11 CERAMIC CHIP180pF 5% 50VC908 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC909 1-126-935-11 ELECT 470µF 20% 16VC910 1-126-962-11 ELECT 3.3µF 20% 50V
C912 1-106-383-00 MYLAR 0.047µF 10% 200VC913 1-119-748-11 ELECT 33µF 20% 400VC914 1-106-383-00 MYLAR 0.047µF 10% 200VC915 1-136-169-00 FILM 0.22µF 5% 50VC916 1-117-626-11 FILM 2000pF 3% 1.2KV
C917 1-117-665-11 FILM 0.33µF 5% 250VC918 1-106-359-00 MYLAR 0.0047µF 10% 100VC919 1-115-350-51 CERAMIC 0.0047µF 2KVC920 1-137-372-11 FILM 0.022µF 5% 50VC921 1-106-228-00 MYLAR 0.22µF 10% 100V
C922 1-106-220-00 MYLAR 0.1µF 10% 100VC923 1-106-355-12 MYLAR 0.0033µF 10% 200VC924 1-106-220-00 MYLAR 0.1µF 10% 100VC925 1-126-967-11 ELECT 47µF 20% 50VC926 1-126-964-11 ELECT 10µF 20% 50V
C927 1-163-243-11 CERAMIC CHIP47pF 5% 50VC928 1-163-133-00 CERAMIC CHIP470pF 5% 50VC929 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC930 1-163-227-11 CERAMIC CHIP10pF 0.5pF 50VC931 1-126-964-11 ELECT 10µF 20% 50V
C932 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC933 1-126-960-11 ELECT 1µF 20% 50VC935 1-163-275-11 CERAMIC CHIP0.001µF 5% 50V
<CONNECTOR>
CN501*1-564-509-11 PLUG, CONNECTOR 6PCN502*1-564-510-11 PLUG, CONNECTOR 7PCN503*1-508-879-11 BASE POSTCN504 1-784-504-11 CONNECTOR, FFC/FPC 25PCN505 1-784-504-11 CONNECTOR, FFC/FPC 25P
CN506 1-764-101-11 PIN, CONNECTOR (PC BOARD) 2PCN508*1-564-511-11 PLUG, CONNECTOR 8PCN509*1-778-955-11 PIN, CONNECTOR (PC BOARD) 10P
<DIODE>
D501 8-719-109-85 ZENER DIODE RD5.1ESB2D502 8-719-109-85 ZENER DIODE RD5.1ESB2D504 8-719-988-61 DIODE 1SS355TE-17D505 8-719-110-36 ZENER DIODE RD13ESB2D506 8-719-991-33 DIODE 1SS133T-77
D507 8-719-063-89 DIODE YG911S3RD508 8-719-031-79 DIODE D5SC4MD509 8-719-991-33 DIODE 1SS133T-77D510 8-719-109-85 ZENER DIODE RD5.1ESB2D511 8-719-066-36 DIODE FMQ-G5GS
D512 8-719-988-61 DIODE 1SS355TE-17
D
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-8
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
D513 8-719-991-33 DIODE 1SS133T-77D514 8-719-991-33 DIODE 1SS133T-77D515 8-719-109-89 ZENER DIODE RD5.6ESB2D516 8-719-991-33 DIODE 1SS133T-77
D517 8-719-951-30 DIODE ERA91-02D519 8-719-988-61 DIODE 1SS355TE-17D520 8-719-988-61 DIODE 1SS355TE-17D522 8-719-988-61 DIODE 1SS355TE-17D701 8-719-991-33 DIODE 1SS133T-77
D702 8-719-991-33 DIODE 1SS133T-77D703 8-719-991-33 DIODE 1SS133T-77D707 8-719-109-85 ZENER DIODE RD5.1ESB2D708 8-719-908-03 DIODE GP08DD709 8-719-948-45 DIODE ERA22-08
D710 8-719-109-85 ZENER DIODE RD5.1ESB2D901 8-719-991-33 DIODE 1SS133T-77D902 8-719-110-31 ZENER DIODE RD12ESB2D904 8-719-988-61 DIODE 1SS355TE-17D905 8-719-110-36 ZENER DIODE RD13ESB2
D906 8-719-063-89 DIODE YG911S3RD907 8-719-930-97 ZENER DIODE HZS16NB2TDD908 8-719-018-82 DIODE RGP02-20EL-6394D909 8-719-930-97 ZENER DIODE HZS16NB2TDD910 8-719-991-33 DIODE 1SS133T-77
D912 8-719-979-58 DIODE EGP10DD913 8-719-991-33 DIODE 1SS133T-77D914 8-719-991-33 DIODE 1SS133T-77D915 8-719-929-72 ZENER DIODE HZS33NB2D917 8-719-988-61 DIODE 1SS355TE-17
D918 8-719-991-33 DIODE 1SS133T-77D919 8-719-991-33 DIODE 1SS133T-77D920 8-719-928-85 ZENER DIODE HZS4.7NB2D921 8-719-988-61 DIODE 1SS355TE-17D922 8-719-018-82 DIODE RGP02-20EL-6394
D924 8-719-110-31 ZENER DIODE RD12ES-B2
<FERRITE BEAD>
FB501 1-410-397-21 FERRITE 1.1µHFB502 1-410-397-21 FERRITE 1.1µHFB503 1-412-911-11 FERRITE 1.1µHFB504 1-412-911-11 FERRITE 1.1µHFB505 1-412-911-11 FERRITE 1.1µH
FB506 1-410-397-21 FERRITE 1.1µHFB507 1-410-397-21 FERRITE 1.1µHFB901 1-410-397-21 FERRITE 1.1µH
<IC>
IC501 8-759-585-82 IC BA9759F-E2IC502 8-759-803-42 IC LA6500-FAIC503 8-759-058-50 IC XRA10324AFIC701 8-759-444-82 IC LA7841LIC901 8-759-585-81 IC BA9758FS-E2
<CHIP CONDUCTOR>
JR002 1-216-296-91 SHORT 0JR003 1-216-295-91 SHORT 0JR004 1-216-295-91 SHORT 0JR005 1-216-296-91 SHORT 0JR006 1-216-295-91 SHORT 0
JR008 1-216-295-91 SHORT 0JR009 1-216-295-91 SHORT 0JR010 1-216-295-91 SHORT 0JR011 1-216-295-91 SHORT 0JR012 1-216-296-91 SHORT 0
JR013 1-216-295-91 SHORT 0JR014 1-216-296-91 SHORT 0JR015 1-216-296-91 SHORT 0JR016 1-216-295-91 SHORT 0JR017 1-216-296-91 SHORT 0
<COIL>
L501 1-412-537-31 INDUCTOR 100µHL502 1-406-673-11 COIL, CHOKE 2.2mHL503 1-406-671-11 COIL, CHOKE 1mHL504 1-406-675-11 COIL, CHOKE 4.7mHL505 1-416-401-31 COIL, CHOKE 5mH
L901 1-412-537-31 INDUCTOR 100µHL902 1-406-660-41 COIL, CHOKE 15µH
<TRANSISTOR>
Q501 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119Q502 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q503 8-729-901-97 TRANSISTOR 2SA1036K-QQ504 8-729-901-87 TRANSISTOR 2SC2411K-CQQ505 8-729-901-97 TRANSISTOR 2SA1036K-Q
Q506 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119Q507 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119Q508 8-729-048-53 TRANSISTOR 2SJ569LS-CB11Q509 8-729-820-73 TRANSISTOR 2SC3746Q510 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119
Q511 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119Q512 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119Q513 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119Q514 8-729-140-50 TRANSISTOR 2SC3209LKQ515 8-729-048-48 TRANSISTOR 2SC5570 (LBSONY)
Q516 8-729-024-95 TRANSISTOR 2SB1565EFQ517 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119Q518 8-729-019-01 TRANSISTOR 2SD2394-EFQ519 8-729-033-25 TRANSISTOR DTC114GKAQ520 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q521 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q522 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q523 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q524 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ525 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119
Q526 8-729-027-35 TRANSISTOR DTA143TKA-T146Q701 8-729-800-32 TRANSISTOR 2SC2362K-G
D
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-9
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
Q702 8-729-178-43 TRANSISTOR 2SC2784-EQ703 8-729-204-91 TRANSISTOR 2SA1049-GRQ704 8-729-207-82 TRANSISTOR 2SC3421-Y
Q705 8-729-207-89 TRANSISTOR 2SA1358-YQ706 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ707 8-729-046-80 TRANSISTOR 2SC4634LS-CB11Q903 8-729-901-87 TRANSISTOR 2SC2411K-CQQ904 8-729-901-97 TRANSISTOR 2SA1036K-Q
Q905 8-729-048-53 TRANSISTOR 2SJ569LS-CB11Q906 8-729-044-21 TRANSISTOR 2SK2655-01R-F165Q907 8-729-033-26 TRANSISTOR DTA114GKAT146Q908 8-729-033-25 TRANSISTOR DTC114GKA
<RESISTOR>
R501 1-215-884-11 METAL OXIDE 47 5% 2W FR502 1-216-059-00 RES,CHIP 2.7K 5% 1/10WR503 1-216-049-91 RES,CHIP 1K 5% 1/10WR504 1-216-049-91 RES,CHIP 1K 5% 1/10WR505 1-216-049-91 RES,CHIP 1K 5% 1/10W
R506 1-216-049-91 RES,CHIP 1K 5% 1/10WR507 1-216-097-91 RES,CHIP 100K 5% 1/10WR508 1-247-815-91 CARBON 220 5% 1/4WR509 1-216-049-91 RES,CHIP 1K 5% 1/10WR510 1-216-675-91 METAL CHIP 10K 0.50%1/10W
R511 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR512 1-215-453-00 METAL 22K 1% 1/4WR513 1-216-049-91 RES,CHIP 1K 5% 1/10WR514 1-216-097-91 RES,CHIP 100K 5% 1/10WR515 1-216-049-91 RES,CHIP 1K 5% 1/10W
R516 1-216-049-91 RES,CHIP 1K 5% 1/10WR517 1-216-689-11 METAL CHIP 39K 0.50%1/10WR518 1-216-691-11 METAL CHIP 47K 0.50%1/10WR519 1-216-081-00 RES,CHIP 22K 5% 1/10WR520 1-247-791-91 CARBON 22 5% 1/4W
R521 1-216-667-11 METAL CHIP 4.7K 0.50%1/10WR522 1-249-437-11 CARBON 47K 5% 1/4WR523 1-216-033-00 RES,CHIP 220 5% 1/10WR524 1-216-049-91 RES,CHIP 1K 5% 1/10WR525 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R526 1-216-097-91 RES,CHIP 100K 5% 1/10WR527 1-216-673-11 METAL CHIP 8.2K 0.50%1/10WR528 1-216-677-11 METAL CHIP 12K 0.50%1/10WR529 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR530 1-216-049-91 RES,CHIP 1K 5% 1/10W
R531 1-216-097-91 RES,CHIP 100K 5% 1/10WR532 1-215-860-11 METAL OXIDE 33 5% 1W FR533 1-211-796-11 FUSIBLE 1 5% 1/2W FR534 1-216-689-11 METAL CHIP 39K 0.50%1/10WR535 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R536 1-216-683-11 METAL CHIP 22K 0.50%1/10WR537 1-249-437-11 CARBON 47K 5% 1/4WR538 1-216-049-91 RES,CHIP 1K 5% 1/10WR539 1-216-097-91 RES,CHIP 100K 5% 1/10WR540 1-215-909-11 METAL OXIDE 47 5% 3W F
R541 1-216-295-91 SHORT 0
R542 1-249-437-11 CARBON 47K 5% 1/4WR543 1-216-677-11 METAL CHIP 12K 0.50%1/10WR544 1-216-049-91 RES,CHIP 1K 5% 1/10WR545 1-216-097-91 RES,CHIP 100K 5% 1/10W
R546 1-216-381-11 METAL OXIDE 0.22 5% 3W FR547 1-219-726-11 METAL 2.2 5% 10WR548 1-249-437-11 CARBON 47K 5% 1/4WR549 1-260-288-11 CARBON 0.47 5% 1/2WR550 1-260-288-11 CARBON 0.47 5% 1/2W
R551 1-216-049-91 RES,CHIP 1K 5% 1/10WR552 1-216-097-91 RES,CHIP 100K 5% 1/10WR553 1-247-815-91 CARBON 220 5% 1/4WR554 1-216-679-11 METAL CHIP 15K 0.50%1/10WR555 1-216-675-91 METAL CHIP 10K 0.50%1/10W
R556 1-216-683-11 METAL CHIP 22K 0.50%1/10WR557 1-216-423-11 METAL OXIDE 27 5% 1W FR558 1-249-437-11 CARBON 47K 5% 1/4WR559 1-216-073-00 RES,CHIP 10K 5% 1/10WR560 1-216-675-91 METAL CHIP 10K 0.50%1/10W
R561 1-215-443-00 METAL 8.2K 1% 1/4WR562 1-216-677-11 METAL CHIP 12K 0.50%1/10WR563 1-216-049-91 RES,CHIP 1K 5% 1/10WR564 1-216-677-11 METAL CHIP 12K 0.50%1/10WR565 1-216-097-91 RES,CHIP 100K 5% 1/10W
R566 1-216-687-11 METAL CHIP 33K 0.50%1/10WR567 1-214-840-00 METAL 100 1% 1/2WR568 1-216-665-11 METAL CHIP 3.9K 0.50%1/10WR569 1-216-691-11 METAL CHIP 47K 0.50%1/10WR570 1-260-332-51 CARBON 2.2K 5% 1/2W
R571 1-249-425-11 CARBON 4.7K 5% 1/4WR572 1-216-385-11 METAL OXIDE 0.47 5% 3W FR573 1-249-437-11 CARBON 47K 5% 1/4WR574 1-216-097-91 RES,CHIP 100K 5% 1/10WR575 1-216-672-11 METAL CHIP 7.5K 0.50%1/10W
R576 1-215-869-11 METAL OXIDE 1K 5% 1W FR577 1-260-310-71 CARBON 33 5% 1/2WR578 1-216-049-91 RES,CHIP 1K 5% 1/10WR579 1-216-049-91 RES,CHIP 1K 5% 1/10WR580 1-214-840-00 METAL 100 1% 1/2W
R581 1-260-316-51 CARBON 100 5% 1/2WR582 1-214-840-00 METAL 100 1% 1/2WR583 1-249-437-11 CARBON 47K 5% 1/4WR584 1-249-437-11 CARBON 47K 5% 1/4WR585 1-216-073-00 RES,CHIP 10K 5% 1/10W
R586 1-216-683-11 METAL CHIP 22K 0.50%1/10WR587 1-215-886-11 METAL OXIDE 100 5% 2W FR588 1-260-085-11 CARBON 68 5% 1/2WR589 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR590 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R591 1-247-807-31 CARBON 100 5% 1/4WR593 1-216-073-00 RES,CHIP 10K 5% 1/10WR594 1-216-683-11 METAL CHIP 22K 0.50%1/10WR595 1-216-659-11 METAL CHIP 2.2K 0.50%1/10WR597 1-216-073-00 RES,CHIP 10K 5% 1/10W
R598 1-216-675-91 METAL CHIP 10K 0.50%1/10WR599 1-216-657-11 METAL CHIP 1.8K 0.50%1/10W
D
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-10
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
R701 1-216-049-91 RES,CHIP 1K 5% 1/10WR702 1-249-393-11 CARBON 10 5% 1/4W FR703 1-215-459-00 METAL 39K 1% 1/4W
R704 1-216-655-11 METAL CHIP 1.5K 0.50%1/10WR705 1-249-413-11 CARBON 470 5% 1/4W FR706 1-249-389-11 CARBON 4.7 5% 1/4W FR707 1-249-389-11 CARBON 4.7 5% 1/4W FR708 1-215-881-11 METAL OXIDE 15 5% 2W F
R709 1-216-049-91 RES,CHIP 1K 5% 1/10WR710 1-216-073-00 RES,CHIP 10K 5% 1/10WR711 1-216-049-91 RES,CHIP 1K 5% 1/10WR713 1-216-059-00 RES,CHIP 2.7K 5% 1/10WR714 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R715 1-249-389-11 CARBON 4.7 5% 1/4W FR716 1-216-689-11 RES,CHIP 39K 5% 1/10WR717 1-216-073-00 RES,CHIP 10K 5% 1/10WR718 1-216-681-11 METAL CHIP 18K 0.50%1/10WR719 1-216-663-11 METAL CHIP 3.3K 0.50%1/10W
R720 1-216-073-00 RES,CHIP 10K 5% 1/10WR721 1-216-073-00 RES,CHIP 10K 5% 1/10WR722 1-260-292-11 CARBON 1 5% 1/2WR723 1-216-663-11 METAL CHIP 3.3K 0.50%1/10WR724 1-216-659-11 METAL CHIP 2.2K 0.50%1/10W
R725 1-214-798-21 METAL 1.8 1% 1/2WR726 1-214-798-21 METAL 1.8 1% 1/2WR727 1-249-381-11 CARBON 1 5% 1/4W FR728 1-215-865-11 METAL OXIDE 220 5% 1W FR729 1-260-292-11 CARBON 1 5% 1/2W
R730 1-216-073-00 RES,CHIP 10K 5% 1/10WR731 1-216-059-00 RES,CHIP 2.7K 5% 1/10WR732 1-219-510-11 CARBON 470K 5% 1/2WR901 1-216-097-91 RES,CHIP 100K 5% 1/10WR902 1-216-117-00 RES,CHIP 680K 5% 1/10W
R903 1-216-089-91 RES,CHIP 47K 5% 1/10WR904 1-216-033-00 RES,CHIP 220 5% 1/10WR906 1-216-033-00 RES,CHIP 220 5% 1/10WR907 1-216-081-00 RES,CHIP 22K 5% 1/10WR908 1-216-399-00 METAL OXIDE 6.8 5% 3W F
R911 1-216-041-00 RES,CHIP 470 5% 1/10WR912 1-216-049-91 RES,CHIP 1K 5% 1/10WR914 1-247-791-91 CARBON 22 5% 1/4WR915 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR916 1-249-397-11 CARBON 22 5% 1/4W F
R917 1-211-824-71 FUSIBLE 220 5% 1/2W FR918 1-219-727-11 METAL 68 5% 10WR919 1-219-748-11 CARBON 4.7K 5% 1/2WR920 1-216-089-91 RES,CHIP 47K 5% 1/10WR921 1-249-429-11 CARBON 10K 5% 1/4W
R922 1-249-389-11 CARBON 4.7 5% 1/4W FR923 1-218-762-11 METAL CHIP 270K 0.50%1/10WR924 1-216-073-00 RES,CHIP 10K 5% 1/10WR925 1-220-825-11 CARBON 330K 5% 1/2WR926 1-219-746-11 CARBON 1K 5% 1/2W
R927 1-219-746-11 CARBON 1K 5% 1/2WR928 1-216-668-11 METAL CHIP 5.1K 0.50%1/10WR929 1-216-675-91 METAL CHIP 10K 0.50%1/10W
R930 1-216-653-11 METAL CHIP 1.2K 0.50%1/10WR931 1-216-653-11 METAL CHIP 1.2K 0.50%1/10W
R932 1-216-049-91 RES,CHIP 1K 5% 1/10WR933 1-216-687-11 METAL CHIP 33K 0.50%1/10WR934 1-216-667-11 METAL CHIP 4.7K 0.50%1/10WR935 1-216-089-91 RES,CHIP 47K 5% 1/10WR937 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R939 1-216-049-91 RES,CHIP 1K 5% 1/10WR940 1-216-073-00 RES,CHIP 10K 5% 1/10WR941 1-216-025-91 RES,CHIP 100 5% 1/10WR943 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR945 1-216-025-91 RES,CHIP 100 5% 1/10W
R1501 1-216-049-91 RES,CHIP 1K 5% 1/10WR1502 1-216-033-00 RES,CHIP 220 5% 1/10WR1503 1-216-681-11 METAL CHIP 18K 0.50%1/10WR1504 1-216-669-11 METAL CHIP 5.6K 0.50%1/10WR1505 1-216-667-11 METAL CHIP 4.7K 0.50%1/10W
R1506 1-216-049-91 RES,CHIP 1K 5% 1/10WR1507 1-216-097-91 RES,CHIP 100K 5% 1/10WR1510 1-216-073-00 RES,CHIP 10K 5% 1/10WR1515 1-215-909-11 METAL OXIDE 47 5% 3W FR1517 1-216-089-91 RES,CHIP 47K 5% 1/10W
R1518 1-216-025-91 RES,CHIP 100 5% 1/10W
<VARIABLE RESISTOR>
[ RV901!1-241-767-21RES, ADJ, CERMET 100K (HVADJ)
<RELAY>
RY501 1-755-198-11 RELAY
<SPARK GAP>
SG901 1-517-499-21 GAP, SPARKSG902 1-519-422-11 GAP, SPARKSG903 1-519-422-11 GAP, SPARK
<TRANSFORMER>
T501 1-435-070-11 TRANSFORMER, HORIZONTAL DRIVET502 1-429-301-11 TRANSFORMER, FERRITE (HCT)T503 1-431-413-21 TRANSFORMER, FERRITE (HST)T505 1-419-127-11 COIL, HORIZONTAL LINEARITYT701 1-431-414-11 TRANSFORMER, FERRITE (DFT)
T901 1-416-402-11 INDUCTOR 500µHT902!X-4560-175-1 TRANSFORMER ASSY, FLYBACK
(NX-4502//J1D4)
<THERMISTOR>
TH501 1-807-796-11 THERMISTORTH502 1-807-796-11 THERMISTOR
***************************************************************************
D
The components identified by [ in this manual have been carefully factory-selected for eachset in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used.
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-11
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
* A-1372-682-A H1 BOARD, COMPLETE[U/C, AEP, SH, EQ for Japan-made set]
* A-1372-691-A H1 BOARD, COMPLETE[U/C for Mexico-made set]
* A-1372-690-A H1 BOARD, COMPLETE[AEP for UK-made set]
****************************
<CAPACITOR>
C802 1-126-791-11 ELECT 10µF 20% 16VC806 1-126-786-11 ELECT 47µF 20% 16V
<CONNECTOR>
CN801*1-564-526-11 PLUG, CONNECTOR 11P
<DIODE>
D801 8-719-064-11 DIODE SPR-325MVW (POWER)
<TRANSISTOR>
Q801 8-729-119-78 TRANSISTOR 2SC2785-HFEQ802 8-729-119-78 TRANSISTOR 2SC2785-HFEQ803 8-729-029-40 TRANSISTOR DTA124ESAQ804 8-729-029-40 TRANSISTOR DTA124ESA
<RESISTOR>
R801 1-249-417-11 CARBON 1K 5% 1/4WR802 1-249-413-11 CARBON 470 5% 1/4WR803 1-247-815-91 CARBON 220 5% 1/4WR804 1-247-815-91 CARBON 220 5% 1/4WR811 1-249-429-11 CARBON 10K 5% 1/4W
R812 1-249-429-11 CARBON 10K 5% 1/4WR813 1-247-863-91 CARBON 22K 5% 1/4WR814 1-249-441-11 CARBON 100K 5% 1/4WR815 1-215-445-00 METAL 10K 1% 1/4WR821 1-215-401-11 METAL 150 1% 1/4W
R822 1-215-413-00 METAL 470 1% 1/4WR823 1-215-421-00 METAL 1K 1% 1/4WR824 1-215-425-00 METAL 1.5K 1% 1/4WR851 1-249-413-11 CARBON 470 5% 1/4WR852 1-247-807-31 CARBON 100 5% 1/4W
R853 1-247-807-31 CARBON 100 5% 1/4W
<SWITCH>
S801 1-771-734-11 SWITCH, TACTILE (MENU)S811 1-571-427-11 SWITCH, SLIDE (INPUT HD15/BNC)S812 1-554-303-21 SWITCH, KEY BOARD (RESET)
<THERMISTOR>
TH801 1-807-796-11 THERMISTOR
***************************************************************************
* A-1388-250-A J BOARD, COMPLETE[U/C, AEP, SH, EQ for Japan-made set]
* A-1388-261-A J BOARD, COMPLETE[U/C for Mexico-made set]
* A-1388-260-A J BOARD, COMPLETE[AEP for UK-made set]
**************************
<CONNECTOR>
CN891*1-691-960-11 PIN, CONNECTOR (PC BOARD) 3P
<SWITCH>
S891! 1-571-433-31 SWITCH, PUSH (AC POWER)
***************************************************************************
* A-1394-946-C N BOARD, COMPLETE[U/C, AEP, SH, EQ for Japan-made set]
* A-1394-951-A N BOARD, COMPLETE[U/C for Mexico-made set]
* A-1394-950-A N BOARD, COMPLETE[AEP for UK-made set]
***************************
<CAPACITOR>
C001 1-163-009-11 CERAMIC CHIP0.001µF 10% 50VC002 1-163-009-11 CERAMIC CHIP0.001µF 10% 50VC003 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC005 1-163-121-00 CERAMIC CHIP150pF 5% 50VC006 1-163-235-11 CERAMIC CHIP22pF 5% 50V
C007 1-163-235-11 CERAMIC CHIP22pF 5% 50VC008 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC011 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC012 1-126-967-11 ELECT 47µF 20% 50VC013 1-126-965-11 ELECT 22µF 20% 50V
C014 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC015 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC016 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC017 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC018 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C019 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC020 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC021 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC022 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC023 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
H1 JN
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-12
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
C024 1-163-009-11 CERAMIC CHIP0.001µF 10% 50VC025 1-163-009-11 CERAMIC CHIP0.001µF 10% 50VC026 1-104-665-11 ELECT 100µF 20% 25VC027 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC028 1-163-220-11 CERAMIC CHIP3pF 0.25pF 50V
C029 1-163-241-11 CERAMIC CHIP39pF 5% 50VC031 1-126-964-11 ELECT 10µF 20% 50VC033 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC036 1-163-037-11 CERAMIC CHIP0.022µF 10% 50VC037 1-126-964-11 ELECT 10µF 20% 50V
C038 1-126-964-11 ELECT 10µF 20% 50VC039 1-126-964-11 ELECT 10µF 20% 50VC040 1-126-964-11 ELECT 10µF 20% 50VC041 1-126-964-11 ELECT 10µF 20% 50VC042 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C043 1-126-965-11 ELECT 22µF 20% 50VC044 1-163-037-11 CERAMIC CHIP0.022µF 10% 50VC045 1-163-037-11 CERAMIC CHIP0.022µF 10% 50VC046 1-163-037-11 CERAMIC CHIP0.022µF 10% 50VC047 1-163-037-11 CERAMIC CHIP0.022µF 10% 50V
C048 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC049 1-126-964-11 ELECT 10µF 20% 50VC050 1-126-964-11 ELECT 10µF 20% 50VC051 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC052 1-126-933-11 ELECT 100µF 20% 16V
C053 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC054 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC055 1-104-664-11 ELECT 47µF 20% 25VC056 1-126-965-11 ELECT 22µF 20% 50VC057 1-126-964-11 ELECT 10µF 20% 50V
C058 1-164-690-91 CERAMIC CHIP0.0022µF 5% 50VC059 1-126-964-11 ELECT 10µF 20% 50VC061 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC062 1-104-665-11 ELECT 100µF 20% 25VC063 1-164-690-91 CERAMIC CHIP0.0022µF 5% 50V
C064 1-115-419-11 CERAMIC CHIP3300pF 5% 25VC065 1-126-960-11 ELECT 1µF 20% 50VC066 1-164-690-91 CERAMIC CHIP0.0022µF 5% 50VC067 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC068 1-136-169-00 FILM 0.22µF 5% 50V
C069 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC070 1-126-767-11 ELECT 1000µF 20% 16VC071 1-163-007-11 CERAMIC CHIP680pF 10% 50VC072 1-126-942-61 ELECT 1000µF 20% 25VC073 1-115-339-11 CERAMIC CHIP0.1µF 10% 50V
C074 1-163-137-00 CERAMIC CHIP680pF 5% 50VC075 1-163-251-11 CERAMIC CHIP100pF 5% 50VC077 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC078 1-136-169-00 FILM 0.22µF 5% 50VC079 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C080 1-126-967-11 ELECT 47µF 20% 50VC082 1-104-664-11 ELECT 47µF 20% 25VC083 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC084 1-126-964-11 ELECT 10µF 20% 50VC085 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C086 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C087 1-126-964-11 ELECT 10µF 20% 50VC089 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC090 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC091 1-126-933-11 ELECT 100µF 20% 16V
C093 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC094 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC095 1-117-722-11 ELECT 2200µF 20% 10VC096 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC097 1-126-964-11 ELECT 10µF 20% 50V
C098 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC099 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC1003 1-104-664-11 ELECT 47µF 20% 25VC1004 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC1005 1-163-005-11 CERAMIC CHIP470pF 10% 50V
C1006 1-164-161-11 CERAMIC CHIP0.0022µF 10% 50VC1007 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC5002 1-126-964-11 ELECT 10µF 20% 50VC5003 1-126-933-11 ELECT 100µF 20% 16VC5004 1-104-664-11 ELECT 47µF 20% 25V
C5005 1-104-664-11 ELECT 47µF 20% 25VC5008 1-104-664-11 ELECT 47µF 20% 25VC5009 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5101 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5103 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
C5105 1-104-664-11 ELECT 47µF 20% 25VC5106 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5108 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5110 1-104-664-11 ELECT 47µF 20% 25VC5203 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
C5205 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5206 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC5301 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5303 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5304 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C5305 1-104-664-11 ELECT 47µF 20% 25VC5306 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5308 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5310 1-104-664-11 ELECT 47µF 20% 25VC5401 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
C5403 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC5404 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC5406 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5408 1-163-005-11 CERAMIC CHIP470pF 10% 50VC5409 1-163-021-91 CERAMIC CHIP0.01µF 10% 50V
C5413 1-164-004-11 CERAMIC CHIP0.1µF 10% 25VC5501 1-126-967-11 ELECT 47µF 20% 50VC5602 1-115-339-11 CERAMIC CHIP0.1µF 10% 50VC5606 1-163-021-91 CERAMIC CHIP0.01µF 10% 50VC5607 1-164-004-11 CERAMIC CHIP0.1µF 10% 25V
<CONNECTOR>
CN001 1-784-500-11 CONNECTOR, FFC/FPC 21PCN002*1-564-511-11 PLUG, CONNECTOR 8PCN007*1-564-512-11 PLUG, CONNECTOR 9PCN010 1-784-504-11 CONNECTOR, FFC/FPC 25PCN011 1-784-504-11 CONNECTOR, FFC/FPC 25P
N
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-13
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
CN5001*1-564-509-11PLUG, CONNECTOR 6PCN5002*1-564-511-11PLUG, CONNECTOR 8PCN5003*1-564-505-11PLUG, CONNECTOR 2P
<DIODE>
D001 8-719-062-51 DIODE 1PS226-115D002 8-719-062-51 DIODE 1PS226-115D003 8-719-062-51 DIODE 1PS226-115D004 8-719-062-51 DIODE 1PS226-115D008 8-719-109-89 ZENER DIODE RD5.6ESB2
D009 8-719-109-89 ZENER DIODE RD5.6ESB2D010 8-719-109-89 ZENER DIODE RD5.6ESB2D012 8-719-109-89 ZENER DIODE RD5.6ESB2D013 8-719-110-17 ZENER DIODE RD10ESB2D015 8-719-801-78 DIODE 1SS184
D016 8-719-109-89 ZENER DIODE RD5.6ESB2D017 8-719-109-89 ZENER DIODE RD5.6ESB2D018 8-719-109-89 ZENER DIODE RD5.6ESB2D020 8-719-988-61 DIODE 1SS355TE-17D021 8-719-988-61 DIODE 1SS355TE-17
D022 8-719-801-78 DIODE 1SS184D023 8-719-801-78 DIODE 1SS184D024 8-719-801-78 DIODE 1SS184D025 8-719-062-51 DIODE 1PS226-115D026 8-719-062-51 DIODE 1PS226-115
D027 8-719-988-61 DIODE 1SS355TE-17D028 8-719-988-61 DIODE 1SS355TE-17D029 8-719-109-85 ZENER DIODE RD5.1ESB2D036 8-719-109-89 ZENER DIODE RD5.6ESB2D037 8-719-109-89 ZENER DIODE RD5.6ESB2
D038 8-719-045-99 ZENER DIODE RD2.2M-T1B
<FERRITE BEAD>
FB001 1-410-397-21 FERRITE 1.1µHFB002 1-410-397-21 FERRITE 1.1µHFB003 1-410-397-21 FERRITE 1.1µHFB51011-412-911-11 FERRITE 1.1µHFB51031-412-911-11 FERRITE 1.1µH
FB52011-412-911-11 FERRITE 1.1µHFB53011-412-911-11 FERRITE 1.1µHFB53031-412-911-11 FERRITE 1.1µHFB54011-412-911-11 FERRITE 1.1µHFB54031-412-911-11 FERRITE 1.1µH
FB56011-412-911-11 FERRITE 1.1µH
<SENSOR>
GS50018-610-154-92 SENSOR, MAGNETIC MIV-212
<IC>
IC001 8-759-650-17 IC CXD8744Q-0004 (Ver. 1.00)IC002 8-759-162-80 IC MM1170BFBIC003 8-759-527-77 IC M24C16-MN6T
IC004 8-759-491-55 IC TC74VHCT74AFT(EL)IC005 8-759-491-55 IC TC74VHCT74AFT(EL)
IC006 8-759-981-48 IC TL082MIC010 8-759-585-70 IC LA7865M-TLMIC011 8-759-442-20 IC 24LC21AT/SNIC5101 8-759-822-07 IC LA6515IC5201 8-759-822-07 IC LA6515
IC5301 8-759-822-07 IC LA6515IC5401 8-759-822-07 IC LA6515
<COIL>
L002 1-406-665-11 COIL, CHOKE 100µHL003 1-406-671-11 COIL, CHOKE 1mH
<TRANSISTOR>
Q001 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ002 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ003 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ004 8-729-028-83 TRANSISTOR DTA124EUA-T106Q005 8-729-033-26 TRANSISTOR DTA114GKAT146
Q006 8-729-027-49 TRANSISTOR DTC123EKA-T146Q007 8-729-901-00 TRANSISTOR DTC124EKQ008 8-729-033-25 TRANSISTOR DTC114GKAQ009 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q010 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R
Q011 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ012 8-729-901-00 TRANSISTOR DTC124EK
<RESISTOR>
R003 1-216-025-91 RES,CHIP 100 5% 1/10WR004 1-216-025-91 RES,CHIP 100 5% 1/10WR005 1-216-025-91 RES,CHIP 100 5% 1/10WR006 1-216-025-91 RES,CHIP 100 5% 1/10WR007 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R008 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR009 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR010 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR014 1-216-049-91 RES,CHIP 1K 5% 1/10WR015 1-249-389-11 CARBON 4.7 5% 1/4W F
R016 1-216-017-91 RES,CHIP 47 5% 1/10WR017 1-216-017-91 RES,CHIP 47 5% 1/10WR018 1-216-049-91 RES,CHIP 1K 5% 1/10WR019 1-216-025-91 RES,CHIP 100 5% 1/10WR020 1-216-025-91 RES,CHIP 100 5% 1/10W
R021 1-216-025-91 RES,CHIP 100 5% 1/10WR022 1-216-025-91 RES,CHIP 100 5% 1/10WR023 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR024 1-216-025-91 RES,CHIP 100 5% 1/10WR025 1-216-025-91 RES,CHIP 100 5% 1/10W
R026 1-216-025-91 RES,CHIP 100 5% 1/10WR029 1-216-073-00 RES,CHIP 10K 5% 1/10WR030 1-216-049-91 RES,CHIP 1K 5% 1/10WR031 1-216-669-11 METAL CHIP 5.6K 0.50%1/10W
N
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-14
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
R032 1-216-665-11 METAL CHIP 3.9K 0.50%1/10W
R034 1-216-049-91 RES,CHIP 1K 5% 1/10WR035 1-216-073-00 RES,CHIP 10K 5% 1/10WR036 1-216-659-11 METAL CHIP 2.2K 0.50%1/10WR039 1-216-025-91 RES,CHIP 100 5% 1/10WR040 1-216-025-91 RES,CHIP 100 5% 1/10W
R042 1-216-073-00 RES,CHIP 10K 5% 1/10WR043 1-216-049-91 RES,CHIP 1K 5% 1/10WR044 1-216-657-11 METAL CHIP 1.8K 0.50%1/10WR045 1-216-049-91 RES,CHIP 1K 5% 1/10WR046 1-216-073-00 RES,CHIP 10K 5% 1/10W
R047 1-216-049-91 RES,CHIP 1K 5% 1/10WR048 1-216-049-91 RES,CHIP 1K 5% 1/10WR049 1-216-073-00 RES,CHIP 10K 5% 1/10WR053 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR054 1-216-077-91 RES,CHIP 15K 5% 1/10W
R055 1-216-077-91 RES,CHIP 15K 5% 1/10WR056 1-216-073-00 RES,CHIP 10K 5% 1/10WR057 1-216-073-00 RES,CHIP 10K 5% 1/10WR058 1-216-067-00 RES,CHIP 5.6K 5% 1/10WR059 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R060 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR061 1-216-049-91 RES,CHIP 1K 5% 1/10WR062 1-216-613-11 METAL CHIP 27 0.50%1/10WR063 1-216-613-11 METAL CHIP 27 0.50%1/10WR064 1-216-613-11 METAL CHIP 27 0.50%1/10W
R066 1-216-049-91 RES,CHIP 1K 5% 1/10WR067 1-216-073-00 RES,CHIP 10K 5% 1/10WR075 1-215-407-00 METAL 270 1% 1/4WR076 1-215-407-00 METAL 270 1% 1/4WR077 1-216-073-00 RES,CHIP 10K 5% 1/10W
R078 1-216-121-91 RES,CHIP 1M 5% 1/10WR079 1-216-295-91 SHORT 0R080 1-216-295-91 SHORT 0R081 1-216-049-91 RES,CHIP 1K 5% 1/10WR082 1-216-049-91 RES,CHIP 1K 5% 1/10W
R084 1-216-073-00 RES,CHIP 10K 5% 1/10WR085 1-216-049-91 RES,CHIP 1K 5% 1/10WR086 1-216-049-91 RES,CHIP 1K 5% 1/10WR090 1-216-073-00 RES,CHIP 10K 5% 1/10WR091 1-216-049-91 RES,CHIP 1K 5% 1/10W
R092 1-216-049-91 RES,CHIP 1K 5% 1/10WR093 1-216-049-91 RES,CHIP 1K 5% 1/10WR094 1-216-049-91 RES,CHIP 1K 5% 1/10WR095 1-216-049-91 RES,CHIP 1K 5% 1/10WR096 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R097 1-216-073-00 RES,CHIP 10K 5% 1/10WR098 1-216-073-00 RES,CHIP 10K 5% 1/10WR099 1-216-049-91 RES,CHIP 1K 5% 1/10WR1001 1-216-049-91 RES,CHIP 1K 5% 1/10WR1002 1-216-049-91 RES,CHIP 1K 5% 1/10W
R1003 1-216-049-91 RES,CHIP 1K 5% 1/10WR1004 1-216-049-91 RES,CHIP 1K 5% 1/10WR1005 1-216-049-91 RES,CHIP 1K 5% 1/10WR1006 1-216-049-91 RES,CHIP 1K 5% 1/10WR1007 1-216-049-91 RES,CHIP 1K 5% 1/10W
R1008 1-216-667-11 METAL CHIP 4.7K 0.50%1/10WR1009 1-216-049-91 RES,CHIP 1K 5% 1/10WR1010 1-216-049-91 RES,CHIP 1K 5% 1/10WR1011 1-216-049-91 RES,CHIP 1K 5% 1/10WR1012 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
R1013 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR1014 1-216-049-91 RES,CHIP 1K 5% 1/10WR1015 1-216-049-91 RES,CHIP 1K 5% 1/10WR1016 1-216-049-91 RES,CHIP 1K 5% 1/10WR1017 1-216-049-91 RES,CHIP 1K 5% 1/10W
R1018 1-216-049-91 RES,CHIP 1K 5% 1/10WR1019 1-216-049-91 RES,CHIP 1K 5% 1/10WR1020 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR1021 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR1022 1-216-659-11 METAL CHIP 2.2K 0.50%1/10W
R1023 1-216-659-11 METAL CHIP 2.2K 0.50%1/10WR1024 1-216-681-11 METAL CHIP 18K 0.50%1/10WR1025 1-216-025-91 RES,CHIP 100 5% 1/10WR1026 1-216-109-00 RES,CHIP 330K 5% 1/10WR1027 1-216-659-11 METAL CHIP 2.2K 0.50%1/10W
R1028 1-216-647-11 METAL CHIP 680 0.50%1/10WR1029 1-216-025-91 RES,CHIP 100 5% 1/10WR1030 1-216-025-91 RES,CHIP 100 5% 1/10WR1031 1-216-025-91 RES,CHIP 100 5% 1/10WR1032 1-216-025-91 RES,CHIP 100 5% 1/10W
R1033 1-216-025-91 RES,CHIP 100 5% 1/10WR1034 1-216-025-91 RES,CHIP 100 5% 1/10WR1035 1-216-025-91 RES,CHIP 100 5% 1/10WR1036 1-216-025-91 RES,CHIP 100 5% 1/10WR1037 1-216-025-91 RES,CHIP 100 5% 1/10W
R1038 1-216-025-91 RES,CHIP 100 5% 1/10WR1039 1-216-025-91 RES,CHIP 100 5% 1/10WR1040 1-216-025-91 RES,CHIP 100 5% 1/10WR1041 1-216-025-91 RES,CHIP 100 5% 1/10WR1042 1-216-025-91 RES,CHIP 100 5% 1/10W
R1043 1-216-025-91 RES,CHIP 100 5% 1/10WR1044 1-216-667-11 METAL CHIP 4.7K 0.50%1/10WR1045 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR1047 1-216-073-00 RES,CHIP 10K 5% 1/10WR1049 1-216-073-00 RES,CHIP 10K 5% 1/10W
R1050 1-216-073-00 RES,CHIP 10K 5% 1/10WR1051 1-216-097-91 RES,CHIP 100K 5% 1/10WR1052 1-216-073-00 RES,CHIP 10K 5% 1/10WR1053 1-216-049-91 RES,CHIP 1K 5% 1/10WR1054 1-216-073-00 RES,CHIP 10K 5% 1/10W
R1055 1-216-049-91 RES,CHIP 1K 5% 1/10WR1056 1-216-073-00 RES,CHIP 10K 5% 1/10WR1057 1-216-049-91 RES,CHIP 1K 5% 1/10WR1058 1-216-073-00 RES,CHIP 10K 5% 1/10WR1059 1-216-049-91 RES,CHIP 1K 5% 1/10W
R1060 1-216-073-00 RES,CHIP 10K 5% 1/10WR1061 1-216-073-00 RES,CHIP 10K 5% 1/10WR1062 1-216-049-91 RES,CHIP 1K 5% 1/10WR1063 1-216-065-91 RES,CHIP 4.7K 5% 1/10WR1064 1-216-049-91 RES,CHIP 1K 5% 1/10W
R1065 1-216-125-00 RES,CHIP 1.5M 5% 1/10W
N
CPD-G500
REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
7-15
The components identified ! marked arecritical for safety.Replace only with the part number specified.
Les composants identifiés par la marque! sont critiques pour la sécurité.Ne les remplacer que par une pièceportant le numéro spécifié. N
R1066 1-216-073-00 RES,CHIP 10K 5% 1/10WR1067 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR1068 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR1069 1-216-049-91 RES,CHIP 1K 5% 1/10W
R1070 1-216-057-00 RES,CHIP 2.2K 5% 1/10WR1071 1-216-081-00 RES,CHIP 22K 5% 1/10WR5003 1-216-295-91 SHORT 0R5005 1-216-081-00 RES,CHIP 22K 5% 1/10WR5006 1-216-073-00 RES,CHIP 10K 5% 1/10W
R5007 1-216-049-91 RES,CHIP 1K 5% 1/10WR5010 1-216-295-91 SHORT 0R5011 1-216-073-00 RES,CHIP 10K 5% 1/10WR5015 1-216-049-91 RES,CHIP 1K 5% 1/10WR5108 1-216-308-00 RES,CHIP 4.7 5% 1/10W
R5109 1-216-308-00 RES,CHIP 4.7 5% 1/10WR5110 1-216-073-00 RES,CHIP 10K 5% 1/10WR5113 1-216-073-00 RES,CHIP 10K 5% 1/10WR5115 1-215-859-00 METAL OXIDE 22 5% 1W FR5116 1-216-073-00 RES,CHIP 10K 5% 1/10W
R5119 1-216-073-00 RES,CHIP 10K 5% 1/10WR5122 1-215-859-00 METAL OXIDE 22 5% 1W FR5205 1-216-073-00 RES,CHIP 10K 5% 1/10WR5206 1-215-859-00 METAL OXIDE 22 5% 1W FR5207 1-216-073-00 RES,CHIP 10K 5% 1/10W
R5208 1-216-069-00 RES,CHIP 6.8K 5% 1/10WR5209 1-216-308-00 RES,CHIP 4.7 5% 1/10WR5308 1-216-308-00 RES,CHIP 4.7 5% 1/10WR5309 1-216-308-00 RES,CHIP 4.7 5% 1/10WR5310 1-216-073-00 RES,CHIP 10K 5% 1/10W
R5313 1-216-073-00 RES,CHIP 10K 5% 1/10WR5315 1-215-859-00 METAL OXIDE 22 5% 1W FR5316 1-216-073-00 RES,CHIP 10K 5% 1/10WR5319 1-216-073-00 RES,CHIP 10K 5% 1/10WR5322 1-215-859-00 METAL OXIDE 22 5% 1W F
R5406 1-216-083-00 RES,CHIP 27K 5% 1/10WR5407 1-216-085-00 RES,CHIP 33K 5% 1/10WR5408 1-216-308-00 RES,CHIP 4.7 5% 1/10WR5409 1-216-308-00 RES,CHIP 4.7 5% 1/10WR5410 1-216-081-00 RES,CHIP 22K 5% 1/10W
R5413 1-216-097-91 RES,CHIP 100K 5% 1/10WR5415 1-215-887-00 METAL OXIDE 150 5% 2W FR5416 1-216-081-00 RES,CHIP 22K 5% 1/10WR5419 1-216-097-91 RES,CHIP 100K 5% 1/10WR5422 1-216-451-11 METAL OXIDE 120 5% 2W F
R5502 1-216-081-00 RES,CHIP 22K 5% 1/10WR5503 1-216-081-00 RES,CHIP 22K 5% 1/10WR5504 1-216-089-91 RES,CHIP 47K 5% 1/10WR5505 1-216-089-91 RES,CHIP 47K 5% 1/10WR5506 1-216-069-00 RES,CHIP 6.8K 5% 1/10W
R5507 1-249-382-11 CARBON 1.2 5% 1/4W FR5508 1-249-382-11 CARBON 1.2 5% 1/4W FR5509 1-249-382-11 CARBON 1.2 5% 1/4W FR5510 1-249-382-11 CARBON 1.2 5% 1/4W FR5602 1-216-081-00 RES,CHIP 22K 5% 1/10W
R5603 1-216-077-91 RES,CHIP 15K 5% 1/10WR5604 1-216-081-00 RES,CHIP 22K 5% 1/10W
R5605 1-216-097-91 RES,CHIP 100K 5% 1/10WR5607 1-215-862-11 METAL OXIDE 68 5% 1W FR5610 1-216-308-00 RES,CHIP 4.7 5% 1/10W
<CRYSTAL>
X001 1-760-682-21 VIBRATOR, CRYSTAL (24.756MHz)