Post on 13-Jan-2020
transcript
Stainless Steel Valves
http://www.toyovalve.co.jp/
GasketGland packingBody materialShell thicknessEnd connectionsF-F dimensionP-T ratingsClassSeries
-IIR-O-ring
SCS13/CF8
Toyo standard
JIS G3448Pipe-End
Toyo standardToyo standard100℃ max. water-0.98MPa
10K
Ball
R-PTFE for strainer onlyNon-asbestos
Screwed type:JIS B0203Flanged type:JIS B2238
Screwed: Toyo standard
Flanged: JIS B2002(Strainer:
Toyo standard)
Toyo standard220℃ max. oil, gas, air, water-0.98MPa
GateGlobeCheckStrainer
-PTFESCS14/CF8MJIS B0203Toyo standard38℃ oil, gas, air, water-5.52MPaSaturated steam 1.03MPa
800Ball
Asbestos (Joint sheet)
AsbestosSCS13/SCS14CF8/CF8M
ASME B16.34
JIS B2238ASME B16.10 (Expect strainers)
JIS B2238(Std. products 300℃ max.)
10KGateGlobeCheckStrainer
Non-asbestos (Spiral wound)20K
Asbestos (Joint sheet)ASME B16.5
ASME B16.34(Std. products 300℃ max.)
150
Non-asbestos (Spiral wound)300
-Non-asbestosfor bypass valve
SCS13/SCS14CF8/CF8M
ASME B16.34Wafer typeJIS B2238
API 594
NBR seat:80℃ max. oil, air, water-0.98MPa
10KRubber seatNBREPDMFPM
NBR seat:80℃ max. oil, air, water-2.55MPa
20K
--
API 600ASME B16.34
10K
Metal seat20K
--Wafer typeASME B16.5
150
300
PTFE seatPTFESCS13/CF8ASME B16.34JIS B0203Toyo standardWorking temp.:-29~200℃Water, oil, gas-1.37MPa (max.)
10KBall
PTFE seatPTFESCS13/SCS14CF8/CF8M
ASME B16.34
JIS B2238
ASME B16.10
JIS B220110K
Ball20K
ASME B16.5ASME B16.34150
300
-PTFESCS13/CF8Toyo standardWafer typeJIS B223810K/16K/20K
JIS B2032 Series 46
PTFE seat:100℃ max. water, oil, gas-0.98MPa(160℃ max)
10KHighperform-ance
Metal seat:100℃ max. water, oil, gas-0.98MPaSaturated steam 1.25MPa(200℃ max)
Notes:1) Although the pressure-temperature ratings for the valve body of V-series are mentioned in the above table, the highest working temperature of the standard packing, made of asbestos, is 260℃ max. However, since it is necessary to consider separately about type of gland packing and gasket depending on an operating condition (fluid, pressure, and temperature), please consult our sales staff or agent for details.2) The standard gasket of 10K and Class 150 V-series gate, globe and check (swing, lift) valves is P#5000AC (asbestos sheet). Moreover, V#7020 (Reinforced Teflon sheet/(R) sheet) is available upon request.3) Gland packings and gaskets made of asbestos will not be furnished after end of year 2003.4) The standard gasket of a strainer is V#7020 (Reinforced Teflon/(R) sheet).
Fluid used forSpecificationGrade
Oxygen, chlorine, explosive fluid, etc.
Carry out degreasing by the chlorine organic solvent, wash and rinse, take inspection by black light irradiation by sampling from every parts, take pressure test with compression nitrogen gas, conduct inspection for all quantity by black light irradiation, and ship out with special packing.
1
Waterworks, food industry, clean room, etc.Carry out degreasing by the chlorine organic solvent, wash and rinse, take pressure test with compression nitrogen gas, conduct inspection by black light irradiation by sampling, and ship out with special packing.
2
Machines, such as an oil free compressor, pre-treatment for paint, etc.
With emphasis on a connection part or external surface, carry out degreasing with an oil solvent, carry out pressure test by air pressure, conduct inspection by black light irradiation by sampling, and ship out with special packing.
3
*Please contact our sales staff or agent for details.
Oil-Free TreatmentValves made with oil-free treatment are used for oxygen line, medical devices, food, painting, etc.Since there is no particular standard for oil-free treatment, we designate three grades with the following specifications.
Butterfly Valves
Flanged
Screwed
Dual Plate Check Valves
V-Series
U-Series
( )
Design Specification
U-SeriesStainless Steel Valves
TOYO StandardDesignGlobe ValvesGate ValvesType
10KClass
830800J800802J802Fig.WD1HLWD1HLWD1HLWD1HLWD1HLSize
0.385593550.30.4
5555
7879
4445
1 / 4"3 / 8"
810
0.470.721.09
637080
99110131
658090
1.82.23.5
556370
8492103
8595110
0.50.71.1
556370
808693
525870
1.82.33.3
556370
8798106
8090100
0.40.50.8
556370
8595103
505562
1 / 2"3 / 4"1"
152025
1.652.303.50
90100110
145165182
105120140
4.55.47.5
8090100
122135158
130150180
1.32.23.4
8090100
105124138
7886100
4.35.26.8
808090
125139163
110125140
1.11.72.6
808090
122136158
707585
11 / 4"11 / 2"2"
324050
SCS13SCS13SCS13SCS13SCS13BodyMaterial SUS304/Chrome platedSUS304/Chrome platedSUS304/Chrome platedSUS304/Chrome platedSUS304/Chrome platedStem
R-PTFESUS304SUS304SCS13SCS13Disc1.37MPa (200psi) WOG non-shock0.98MPa (143psi) Saturated steamSee P-T rating on page 12
1.37MPa (200psi) WOG non-shock0.71MPa (100psi) Saturated steamSee P-T rating on page 12
Service conditions
R-PTFE seatRemarks
TOYO StandardDesignStrainersSwing Check ValvesGlobe ValvesType
10KClass
809J809804J804830JFig.WHLWHLWHLWHLWD1HLSize
1 / 4"3 / 8"
810
1.62.03.1
54.066.078.0
120130150
0.40.60.8
50.560.571.0
7893108
1.82.23.3
43.549.058.0
8595110
0.30.40.6
41.649.558.0
567080
1.82.23.5
637080
100111132
8595110
1 / 2"3 / 4"1"
152025
4.24.86.2
90.5104.0133.5
170190220
1.11.62.6
82.093.0119.0
128143173
4.15.06.5
64.573.586.0
130150180
1.01.42.0
68.780.597.5
96110128
4.55.47.5
90100110
145166182
130150180
11 / 4"11 / 2"2"
324050
SCS13BodySCS13BodySCS13BodyMaterial SUS304ScreenSUS304/Chrome platedPinSUS304/Chrome platedStem
SCS13DiscR-PTFEDisc1.37MPa (200psi) WOG non-shock0.98MPa (143psi) Saturated steamSee P-T rating on page 12
Service conditions
40 meshes screenR-PTFE seatRemarks
(mm)
(mm)
H
L
H
L
H
LH
L L
H
U-SeriesStainless Steel Valves
TOYO StandardDesignBall ValvesType800Class
Std. boreReduced boreReduced boreReduced boreReduced bore45804550W4550A3550W3550Fig.
WD1HLdWD1HLdWD1HLdWD1HLdWD1HLdSize0.110.14
4040
21.524.0
39.045.0
5.07.0
0.080.12
62.571.0
3537
39.045.0
5.07.0
0.110.14
4040
21.524.0
39.045.0
5.07.0
0.080.12
62.571.0
3537
39.045.0
5.07.0
1 / 4"3 / 8"
810
0.280.400.64
100100130
505560
607080
101520
0.180.26
6060
30.533.5
57.559.0
9.112.5
0.190.270.43
87.587.5104.5
434650
57.559.071.0
9.112.515.0
0.180.26
6060
30.533.5
57.559.0
9.112.5
0.190.270.43
87.587.5104.5
434650
57.559.071.0
9.112.515.0
1 / 2"3 / 4"1"
152025
0.991.532.36
130150150
647379
95108124
253238
0.700.861.37
104.5125.5125.5
546572
78.083.0100.0
20.024.532.0
0.700.861.37
104.5125.5125.5
546572
78.083.0100.0
20.024.532.0
11 / 4"11 / 2"2"
324050
SCS14ASCS14ASCS14ASCS13ASCS13ABody
MaterialSUS316/Chrome platedSUS316/Chrome platedSUS316/Chrome platedSUS304/Chrome platedSUS304/Chrome platedStem
SUS316SUS316SUS316SUS316SUS316BallR-PTFER-PTFER-PTFER-PTFER-PTFESeat
5.52MPa (800psi) WOG, non-shock1.03MPa (150psi) Saturated steam
Service conditions
Remarks
TOYO StandardDesignBall ValvesType
10K800Class
Full boreFull boreStd. bore30604760A3380Fig.
WD1HLdWD1HLdWD1HLdSize
0.62115536010
1 / 4"3 / 8"
810
0.831.031.61
115115150
555971
708090
131925
0.390.600.91
100130130
556063
677489
152025
0.310.420.65
100100120
697277
607080
101520
1 / 2"3 / 4"1"
152025
1.983.254.55
150200200
76100108
105115135
323851
1.562.143.42
150150200
7278105
106118129
323850
1.031.422.33
130130150
9095103
90100120
253240
11 / 4"11 / 2"2"
324050
SCS13SCS14ASCS13ABody
MaterialSUS304SUS316/Chrome platedSUS304/Chrome platedStemSUS304SUS316SUS304BallPTFER-PTFER-PTFESeat
1.37MPa (200psi) WOG, non-shock0.5MPa (70psi) Saturated steam
5.52MPa (800psi) WOG, non-shock0.5MPa (70psi) Saturated steam
5.52MPa (800psi) WOG, non-shock1.03MPa (150psi) Saturated steam
Service conditions
Remarks
(mm)
(mm)
H
L
D1
H
L
D1
Pipe-Joint Stainless Steel Valves
TOYO StandardDesignStrainerSwing Check ValveBall ValvesGate ValveType
10KClass
Full boreStd. bore84784430663086842Fig.WHLWHLWD1HLdWD1HLdWD1HLSize0.350.500.72
50.560.571.0
133144156
0.410.600.77
444958
108118124
0.610.881.52
100120130
727790
121130135
142025
0.510.610.88
100100120
697277
113121130
101520
0.460.570.74
556370
8595103
107112119
13Su×1 / 2"20Su×3 / 4"25Su×1"
1.231.692.70
82.093.0119.0
176188219
1.371.792.76
657486
140151171
2.003.054.08
130150200
95103134
155170183
324046
1.521.983.05
130130150
9095103
141155170
253240
1.271.702.32
808090
122136158
133143149
30Su×11 / 4"40Su×11 / 2"50Su×2"
SCS13ABodySCS13ABodySCS13ASCS13ABodySCS13ABody
MaterialSUS304ScreenSUS304/Chrome platedPinSUS304/Chrome platedSUS304/Chrome platedStemSUS304/Chrome platedStem
SCS13ADiscSUS304SUS304BallSCS13ADiscPTFEPTFESeat
100℃ water 1.0MPaService conditions
Remarks
Leak proof, Pull-out resistant, No special tools required
H
L
D
H
L
U-SeriesPipe End Valves
TOYO StandardDesignBall ValvesGate ValvesType
10KClass
Std. bore3087843Fig.
WD1HLdWD1HLSize0.320.460.77
100100120
687276
177194228
101520
0.450.500.73
556370
8595103
203184215
13Su×1 / 2"20Su×3 / 4"25Su×1"
1.301.803.10
130130150
9095103
295344434
253240
30Su×11 / 4"40Su×11 / 2"50Su×2"
SCS13BodySCS13Body
MaterialSUS304/Chrome platedStemSUS304/Chrome platedStemSUS304BallSCS13DiscPTFESeat
100℃ water 1.0MPaService conditions
Long neck for thermal insurationT-Handle available
Pipe material: SUS304TPDRemarks
H
L
D1
H
L
V-SeriesStainless Steel Valves
API 603DesignGate ValvesType
20K/30010K/15010KClass
863J/863813J/813853J/853803803JFig.WD1HLWD1HLWD1HLWD1HLWD1HLSize5.26.59.0
100100140
216225250
140152165
5.26.59.0
100100140
216225250
140152165
3.24.04.8
100100100
214214227
108117127
3.24.04.8
100100100
214214227
108117127
3.54.05.0
100100100
206212232
108117127
1 / 2"3 / 4"1"
152025
11.714.520.0
160160200
300308333
178190216
11.714.520.0
160160200
300308333
178190216
6.78.011.0
140140160
257264308
140165178
6.78.011.0
140140160
257264308
140165178
7.08.010.5
140140160
259277312
140165178
11 / 4"11 / 2"2"
324050
28.042.060.2
200250300
378433537
241283305
28.042.060.2
200250300
378433537
241283305
18.021.531.5
180200224
357417508
190203229
18.021.531.5
180200224
357417508
190203229
14.018.525.5
180200230
366433510
190203229
21 / 2"3"4"
6580100
90.0110.0170.0
355400450
658758950
381403419
90.0110.0170.0
355400450
658758950
381403419
46.058.092.0
280300355
619728923
254267292
46.058.092.0
280300355
619728923
254267292
40.046.075.0
250250300
620709915
254267292
5"6"8"
125150200
290.0445.0
560600
11381329
457502
290.0445.0
560600
11381329
457502
162.0245.0360.0
400450550
111713171650
330356381
162.0245.0360.0
400450550
111713171650
330356381
124.0360110933010"12"14"
250300350
SCS14/CF8MSCS13/CF8SCS14/CF8MSCS13/CF8SCS13ABodyMaterial SUS316/F316SUS304/F304SUS316/F316SUS304/F304SUS304Stem
SCS14/CF8MSCS13/CF8SCS14/CF8MSCS13/CF8SCS13ADisc10K/20K: See P-T rating for JIS flanged valves on page 13Class 150/300: See P-T rating for ASME flanged valves on page 13
Service conditions
Remarks
(mm)
TOYO StandardAIP 603JPI-7S-58 / API 603DesignGlobe with PTFE seatGlobe ValvesType
10K20K/30010K/150Class
831J/881J861J/861811J/811851J/851801J/801Fig.WD1HLWD1HLWD1HLWD1HLWD1HLSize2.64.04.5
100100100
176178180
108117127
4.07.08.0
100140140
181208208
152178203
4.07.08.0
100140140
181208208
152178203
2.63.03.5
100100100
176178180
108117127
2.63.03.5
100100100
176178180
108117127
1 / 2"3 / 4"1"
152025
7.07.510.5
140140160
211211237
140165203
12.215.018.0
160160180
237237285
216229267
12.215.018.0
160160180
237237285
216229267
5.67.010.5
140140160
206206237
140165203
5.67.010.5
140140160
206206237
140165203
11 / 4"11 / 2"2"
324050
14.321.532.5
180200250
280321365
216241292
26.536.554.0
224250355
328370445
292318356
26.536.554.0
224250355
328370445
292318356
15.523.036.5
180200250
280321365
216241292
15.523.036.5
180200250
280321365
216241292
21 / 2"3"4"
6580100
46.566.0116.0
250355450
414488610
356406495
81.0111.0197.0
400450450
495554630
400444559
81.0111.0197.0
400450450
495554630
400444559
50.069.0128.0
250355450
414488610
356406495
50.069.0128.0
250355450
414488610
356406495
5"6"8"
125150200
SCS13/SCS14SCS14/CF8MSCS13/CF8SCS14/CF8MSCS13/CF8BodyMaterial SUS304/SUS316SUS316/F316SUS304/F304SUS316/F316SUS304/F304Stem
PTFESUS316/F316SUS304/F304SUS316/F316SUS304/F304Disc10K/20K: See P-T rating for JIS flanged valves on page 13Class 150/300: See P-T rating for ASME flanged valves on page 13
Service conditions
Class 150 availableRemarks
(mm)
H
L
H
L
V-SeriesStainless Steel Valves
TOYO StandardTOYO StandardJPI-7S-58DesignStrainersSwing Check ValvesType10K/15020K/30010K/150Class
857J/857807J/807865J/865815J/815855J/855805J/805Fig.WHLWHLWHLWHLWHLWHLSize2.03.14.1
668080
125140160
2.03.14.1
668080
125140160
1 / 2"3 / 4"1"
152025
6.56.89.0
110110135
180190220
6.56.89.0
110110135
180190220
16.522.2
162167
241267
16.522.2
162167
241267
7.410.2
117117
165203
7.410.2
117117
165203
11 / 4"11 / 2"2"
324050
16.519.029.5
195220260
270298350
16.519.029.5
195220260
270298350
32.038.560.0
175180214
292318356
32.038.560.0
175180214
292318356
14.519.033.0
138144165
216241292
14.519.033.0
138144165
216241292
21 / 2"3"4"
6580100
44.054.577.0
265315375
390440540
44.054.577.0
265315375
390440540
78.7118.0207.0
235278325
400444533
78.7118.0207.0
235278325
400444533
46.067.0133.0
186209266
330356495
46.067.0133.0
186209266
330356495
5"6"8"
125150200
98.049068098.0490680320.0500.0
395494
622711
320.0500.0
395494
622711
170.0260.0
303356
622698
170.0260.0
303356
622698
10"12"
250300
SCS14/CF8MSCS13/CF8BodySCS14/CF8MSCS13/CF8SCS14/CF8MSCS13/CF8BodyMaterial SUS316/F316SUS304/F304ScreenSUS316/F316SUS304/F304SUS316/F316SUS304/F304Pin
SUS316/F316SUS304/F304SUS316/F316SUS304/F304Disc10K/20K: See P-T rating for JIS flanged valves on page 13Class 150/300: See P-T rating for ASME flanged valves on page 13
Service conditions
Remarks
TOYO StandardJPI-7S-58DesignLift Check ValvesType
20K/30010K/150Class
884J/884834J/834874J/874824J/824Fig.WHLWHLWHLWHLSize3.25.16.2
738484
152178203
3.25.16.2
738484
152178203
1.82.32.8
646667
108117127
1.82.32.8
646667
108117127
1 / 2"3 / 4"1"
152025
8.511.8
103103
216229
8.511.8
103103
216229
4.76.58.0
828295
140165203
4.76.58.0
828295
140165203
11 / 4"11 / 2"2"
324050
SCS14/CF8MSCS13/CF8SCS14/CF8MSCS13/CF8BodyMaterial SUS316/F316SUS304/F304SUS316/F316SUS304/F304Disc
10K/20K: See P-T rating for JIS flanged valves on page 13Class 150/300: See P-T rating for ASME flanged valves on page 13
Service conditions
Remarks
(mm)
(mm)
L
H
H
L
Flanged Ball Valves
TOYO StandardDesignBall ValvesType
10K/15010KClass
4031L/4131L3031L/3131L3011L/4011LFig.WD1HWD1HLdWD1HWD1HLdWD1HLdSize
2.22.84.3
115115150
747895
108117127
131925
2.22.84.3
115115150
747895
108117127
131925
2.22.64.5
130130160
818493
108117127
152025
1 / 2"3 / 4"1"
152025
5.55.88.7
150200200
100126134
140165178
323851
5.55.88.7
150200200
100126134
140165178
323851
5.97.59.2
160230230
97113120
140165178
324050
11 / 4"11 / 2"2"
324050
16.021.437.2
320320450
164173210
190203229
6576102
16.021.437.2
320320450
164173210
190203229
6576102
14.619.828.1
400400460
150161189
190203229
6580100
21 / 2"3"4"
6580100
74.090.0145.0
300300300
293312383
50.076.4137.0
8008001120
269288374
356394457
127152203
74.090.0145.0
300300300
293312383
50.076.4137.0
8008001120
269288374
356394457
127152203
53.772.2156.9
4609801970
209262317
356394457
125150200
5"6"8"
125150200
SCS14/CF8MSCS13/CF8SCS13/SCS14Body
MaterialSUS316/F316SUS304/F304SUS304/SUS316Stem
SUS316 or SCS14/F316 or CF8MSUS304 or SCS13/F304 or CF8SCS13/SCS14BallR-PTFER-PTFER-PTFESeat
See P-T rating on page 14Service conditions
Remarks
(mm)
(Gear : 4031G/4131G)(Gear : 3031G/3131G)
TOYO StandardDesignBall ValvesType20K/300Class
4331L/4231L3331L/3231LFig.WD1HWD1HLdWD1HWD1HLdSize
2.53.15.1
115115150
747895
140152165
131925
2.53.15.1
115115150
747895
140152165
131925
1 / 2"3 / 4"1"
152025
10.514.0
200200
126134
190216
3851
10.514.0
200200
126134
190216
3851
11 / 4"11 / 2"2"
324050
22.530.553.0
320320600
164173210
241283305
6576102
22.530.553.0
320320600
164173210
241283305
6576102
21 / 2"3"4"
6580100
93.0138.0203.0
300300400
293346393
70.099.0164.0
80011201400
269336385
381403502
127152203
93.0138.0203.0
300300400
293346393
70.099.0164.0
80011201400
269336385
381403502
127152203
5"6"8"
125150200
SCS14/CF8MSCS13/CF8Body
MaterialSUS316/F316SUS304/F304Stem
SUS316 or SCS14/F316 or CF8MSUS304 or SCS13/F304 or CF8BallR-PTFER-PTFESeat
See P-T rating on page 14Service conditions
Remarks
(mm)
(Gear : 4331G/4231G)(Gear : 3331G/3231G)
H
LL
H
Dual Plate Check Valves
TOYO StandardDesignDual Plate Check ValvesType
20K/30010K/15020K10KClass
816M/816MW806M/806MW816806Fig.WDLWDLWD1HLWD1HLSize
3111602.53
85105
6060
1.72.3
6363
118126
5460
1.72.3
6363
118126
5460
11 / 2"2"
4050
478
130149181
677373
468
124137175
677373
3.04.15.8
636363
134138151
677373
3.04.05.5
636363
134138151
677373
21 / 2"3"4"
6580100
141936
216251308
8698127
101632
197222279
8698127
8.514.025.0
707070
174188215
8698127
8.012.022.0
707070
174188215
8698127
5"6"8"
125150200
5188176
362422486
146181222
478497
340410451
146181184
39.050.5
8080
254282
146181
35.045.0
8080
254282
146181
10"12"14"
250300350
227300373
540597654
232264292
160185243
514549606
191203219
16"18"20"
400450500
SCS13/CF8SCS13/CF8SCS13SCS13BodyMaterial SCS13/CF8SCS13/CF8SCS13SCS13Plate
SCS13/CF8 (Matal)SCS13/CF8 (Matal)NBRNBRSeatSee P-T rating on page 13Service conditions
SCS14/CF8M body available upon requestRemarks
(mm)
L
D
D1L
H
Pressure-Temperature Ratings
U-Series Stainless Steel Valves
■Gate, Globe, Check Valves & Strainers / screwed & flanged endsU-Series Stainless Steel Valves
■Ball Valves / screwed end type � Fig. 3550, 4550A, 4580, 3380, 4760A or 3060
V-Series Stainless Steel Valves
■JIS Flanged Valves � (Extracted from JIS B2238, General rules for steel pipe flanges)�■Pipe-End Valves /Abacus Joint End Valves
Class 800WOGMPa psi1.37�0.98�0.98�0.98�2.10�0.55
Less than 120℃�220℃�
Less than 220℃�Saturated steamAir, gas, oil,
shell waterseat air
200�143�143�143�300�80
Service conditions
Test pressure
MPa0.98�1.50�0.55
psiLess than 100℃ water
shell waterseat air
143�215�80
Service conditions
Test pressure
Static water
Class 800WOG 10KMPa psi MPa psi
1.03�8.30�0.55
Saturated steamshell waterseat air
150�1200�80
1.03�2.10�0.55
150�300�80
Service conditions
Test pressure
Water, oil , air 5.52 800 1.37 200WOG 38℃�(3 F゚)��
0.6
1.2
0
0.2
0.2
0.5
1.0 0.98
0
100
0.4
0.8
1.0
1.4(MPa)�
100
(℃)�
Temperature(℃/ F゚)�
Temperature(℃/ F゚)�
Temperature(℃/ F゚)�
250200150100500-50
-100 0 32
0
320 100 200 ( F゚)�
50 100 (℃)�
100 200 300 400 500( F゚)�
4003002001000-100-200-300 ( F゚)�
�0
Pressure(MPa/psi)�
Pressure(MPa/psi)�
Pressure(MPa/psi)�
0
3.0
6.0
-200 -100 100 200
1.0
2.0
4.0
5.0
7.0
(℃)�
0.98
1.37
Water, non-shock
Air, gas, oil, water
←-29 ←220
←-196
200
(psi)� (MPa)�1000
5.52800
600
400
20010K1.37
0
(psi)�
(MPa)�(psi)�
←-29
Class800
Body material10KNominal pressureSCS13 / SCS14
20K
MPa psi MPa psi1.37�1.18�1.18�0.98�―�―�―�―�2.10�0.55
below 120℃�below 220℃�below 220℃�300℃�350℃�400℃�425℃�450℃�
shell waterseat air
200�170�170�143�―�―�―�―�300� 80
483�441�441�412�370�328�285�―�726� 80
3.33�3.04�3.04�2.84�2.55�2.26�1.96�―�5.00�0.55
Service conditions
Test pressure
Static water
Steam,air,gas,oil,�water
Steam,air,gas,oil
Notes: �1)Due to no standard for SCS13 & SCS14 on JIS standard, it� applies as follows. � a. 10K flange type: The value of SCPH1 is applied. � b. 20K flange type: The value of SCPH2 is applied. �2)The max. working temperature for standard products is� restricted to 260℃ by PTFE gland packing, gasket or seat. �3)In case of use at 260℃ and above, applicable selection for� gland packing & gasket is required.
Pressure-Temperature Ratings
V-Series Stainless Steel Valves
■ASME B16.34 Table 2-2.1A & 2-2.2A
Service temperatureClass 150
A351 Gr. CF8(SCS13)� A351 Gr. CF8M(SCS14)� A351 Gr. CF8(SCS13)� A351 Gr. CF8M(SCS14) Class 300
(℃)� ( F゚)� MPa psi MPa psi MPa psi MPa psi
Test�pressure
Note: �(1) For welding end valves only. Flanged ends ratings terminate at 1000°F.
Note:An EPDM seat shall not be used for all oil application.
shell(water) 2.93 425 2.93 425 7.58 1100 7.58 1100seat(air)� 0.55 80 0.55 80 0.55 80 0.55 80
-29 -38�93�149�204�260�316�343�371�399�427�454�482�510�538�566�593�621�649�677�704�732�760�788�816
-20 -100�200�300�400�500�600�650�700�750�800�850�900�950�1000�1050�1100�1150�1200�1250�1300�1350�1400�1450�1500
1.90�1.62�1.41�1.24�1.17�0.965�0.862�0.758�0.655�0.552�0.448�0.345�0.241�0.138�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.103(1)�0.069(1)�
275�230�205�190�170�140�125�110�95�80�65�50�35�20�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�15(1)�10(1)�
1.90�1.65�1.48�1.34�1.90�0.965�0.862�0.758�0.655�0.552�0.448�0.345�0.241�0.138�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�0.138(1)�
275�235�215�195�170�140�125�110�95�80�65�50�35�20�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�20(1)�
4.96�4.14�3.65�3.24�3.00�2.86�2.83�2.79�2.76�2.72�2.69�2.65�2.59�2.24�2.14�1.79�1.34�1.07�0.758�0.586�0.414�0.345�0.241�0.172
720�600�540�495�465�435�430�425�415�405�395�390�380�320�―�255�200�155�115�85�60�50�35�25
4.96�4.27�3.86�3.55�3.31�3.10�3.07�2.96�2.93�2.86�2.79�2.72�2.65�2.52�2.48�2.24�1.90�1.41�1.240�0.965�0.724�0.517�0.414�0.276
720�620�560�515�480�450�445�430�425�420�420�415�385�350�345�305�235�185�145�115�95�75�60�40
Ratings 10K
Fig. 806M(10K)and 816M(20K)�Fig. 806, 10K
20KMPa psi MPa psi1.37�1.18�1.18�0.98�―�―�―�2.10�0.55
below 120℃�above 220℃�below 220℃�above 300℃�above 350℃�below 400℃�above 425℃�shell waterseat air
200�170�170�143�―�―�―�300� 80
483�441�441�412�370�328�285�725� 80
3.33�3.04�3.04�2.84�2.55�2.26�1.96�5.00�0.55
Service conditions
Test pressure
Static water
Oil,gas,water,air
Steam,air,gas,oil
FPM EPDMMPa psi MPa psi1.37�―�1.18�1.18�2.10�0.55
below 80℃�above 120℃�below 80℃�above 120℃�shell waterseat air
Service conditions
Seat material
200�―�170�170�300� 80
1.37�1.37�1.18�1.18�2.10�0.55
200�200�170�170�300� 80
NBRMPa psi1.37�―�1.18�―�2.10�0.55
200�―�170�―�300� 80
Static water
Oil,gas,�water,air
Test pressure
Note:�1)Standard products are designed up to 150℃.�2)In case of use at 150℃ & above, please consult us. �
Fig. 806MW(150) and 816MW(300) �Please refer to table for ASME B16.34. �
Note:�1)Standard products are designed up to 150℃.�2)In case of use at 150℃ & above, please consult us.
Dual Plate Check Valves
■Rubber Seat(With Bypass-Valve) ■Metal Seat(Without Bypass-Valve)
Note:An EPDM seat shall not be used for all oil applications.
Fig. 816, 20K
FPM EPDMMPa psi MPa psi3.33�―�2.55�1.96�5.00�0.55
below 80℃�above 120℃�below 80℃�above 120℃�shell waterseat air
Service conditions
Seat material
483�―�370�285�725� 80
3.33�3.33�2.55�1.96�5.00�0.55
483�483�370�285�725� 80
NBRMPa psi3.33�―�2.55�―�5.00�0.55
483�―�370�―�725� 80
Static water
Oil,gas,�water,air
Test pressure
1000 7.0
6.0
5.0
4.0
3.0
2.0
1.0
800
600
400
200
0
Pressure(MPa/psi)�
(MPa)�(psi)�
0
0 100 200 300 400 500 ( F゚)�
50 100 150 200 250 (℃)�
Temperature(℃/ F゚)�
SIZE 200A
1000 7.0
6.0
5.0
4.0
3.0
2.0
1.0
800
600
400
200
0
Pressure(MPa/psi)�
(MPa)�(psi)�
0
0 100 200 300 400 500 ( F゚)�
50 100 150 200 250 (℃)�
Temperature(℃/ F゚)�
SIZE 80 & 100A
1000 7.0
6.0
5.0
4.0
3.0
2.0
1.0
800
600
400
200
0
Pressure(MPa/psi)�
(MPa)�(psi)�
0
0 100 200 300 400 500 ( F゚)�
50 100 150 200 250 (℃)�
Temperature(℃/ F゚)�
SIZE 125 & 150A
Pressure-Temperature Ratings
10/20K, Class 150/300 Stainless Steel Valves
�
�
1000 7.0
6.0
5.0
4.0
3.0
2.0
1.0
800
600
400
200
0
Pressure(MPa/psi)�
(MPa)�(psi)�
0
0 100 200 300 400 500 ( F゚)�
50 100 150 200 250 (℃)�
Temperature(℃/ F゚)�
SIZE 15 & 20A
1000 7.0
6.0
5.0
4.0
3.0
2.0
1.0
800
600
400
200
0
Pressure(MPa/psi)�
(MPa)�(psi)�
0
0 100 200 300 400 500 ( F゚)�
50 100 150 200 250 (℃)�
Temperature(℃/ F゚)�
SIZE 25~65A
300 Body rating
CF8 (SCS13)
20K Body rating
Seat rating (R-PTFE)
Seat rating (PTFE)
CF8M (SCS14)
CF8M (SCS14)
CF8 (SCS13)
150 Body rating
10K Body rating
Seat rating (R-PTFE)
Seat rating (PTFE)
300 Body rating
CF8 (SCS13)
20K Body rating
CF8M (SCS14)
CF8M (SCS14)
CF8 (SCS13)
150 Body rating
10K Body rating
Seat rating (R-PTFE)
CF8 (SCS13)
CF8M (SCS14)
CF8M (SCS14)
300 Body rating
Seat rating (PTFE)
20K Body rating
150 Body rating
10K Body rating
CF8 (SCS13)
300 Body rating
20K Body rating
Seat rating (PTFE)
150 Body rating
10K Body rating
CF8 (SCS13)
Seat rating (R-PTFE)
CF8M (SCS14)
CF8M (SCS14)
CF8 (SCS13)
300 Body rating
Seat rating(R-PTFE)
20K Body rating
Seat rating (PTFE)
150 Body rating
10K Body rating
CF8 (SCS13)
CF8M (SCS14)
CF8M (SCS14)
CF8 (SCS13)
Distributed by:
5-7, 1-CHOME, NIHONBASHI-MUROMACHI, CHUO-KU, TOKYO 103-0022, JAPAN
TEL: +81-3-3242-3320 FAX: +81-3-3242-3295E-mail: tvjho@toyovalve.co.jphttp://www.toyovalve.co.jp NO.450
T030703A(SE)