Post on 23-Apr-2018
transcript
Job Name: Location: Date:
Purchaser: Engineer:
Submitted to: For Reference Approval Construction
Unit Designation: Schedule No.:
Cooling*Rated Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30,000 Btu/hMinimum Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . .18,000 Btu/hSEER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15.6 Btu/h/WTotal Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2,450 WHeating*Rated Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32,000 Btu/hMinimum Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . .18,000 Btu/hHSPF (IV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.8 Btu/h/WTotal Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..3,440 WHeating at 17°F*Rated Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32,000 Btu/hTotal Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..5,720 W* Rating Conditions (Cooling) - Indoor: 80ºF (27ºC) DB / 67ºF (19ºC) WB.Outdoor: 95ºF (35ºC) DB / 75ºF (24ºC) WB.(Heating) - Indoor: 70ºF (21ºC) DB / 60ºF (16ºC) WB. Outdoor: 47ºF (8ºC) DB /43ºF (6ºC) WB. (Heating) - Indoor: 70ºF (21ºC) DB / 60ºF (16ºC) WB. Outdoor: 17ºF (-8ºC) DB /15ºF (-9ºC) WB.
Power Supply . . . . . . . . . . . . . . . . . . . . 208 / 230V, 1-Phase, 60 HzBreaker Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 AVoltageIndoor - Outdoor S1-S2 . . . . . . . . . . . . . . . . . . . . . . AC 208 / 230VIndoor - Outdoor S2-S3 . . . . . . . . . . . . . . . . . . . . . . . . . . . .DC 24VIndoor - Wired Remote Controller. . . . . . . . . . . . . . . . . . . . .DC 12V
Operating rangeIndoor Intake Air Temp. Outdoor Intake Air Temp.
Cooling Maximum 90ºF (32ºC) DB, 73ºF (23ºC) WB 115ºF (46ºC) DB
Minimum 66ºF (19ºC) DB, 59ºF (15ºC) WB 0ºF** (-18ºC) DB
Heating Maximum 83ºF (28ºC) DB 70ºF (21ºC) DB, 59ºF (15ºC) WB
Minimum 63ºF (17ºC) DB -13ºF (-25ºC) DB, -13ºF (-25ºC) WB
** With optional wind baffle accessory installed. If not installed, the minimum temperature will be 23ºF (-5ºC) DB.
Indoor Unit: PLA-A30BA
Outdoor Unit: PUZ-HA30NHAindoor UnitMCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 A Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.51 F.L.A.Fan Motor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 WAirflow (Lo - M1 - M2 - Hi) . . . . . . . 490 - 570 - 640 - 740 Dry CFM 460 - 530 - 600 - 710 Wet CFMSound Pressure Level (Lo - M1 - M2 - Hi) . . 28 - 30 - 32 - 34 dB(A)
DiMenSiOnS Unit inCHeS / MM paneL inCHeS / MMW 33-1/16 / 840 37-3/8 / 950D 33-1/16 / 840 37-3/8 / 950H 10-3/16 / 258 1-3/8 / 35
Weight (Unit/Grille)lbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 / 13kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 / 6Field Drainpipe Size O.D. . . . . . . . . . . . . . . . . . . . . . 1-1/4" / 32 mmWall-mounted Remote Controller . . . . . . . . . . . . . . . . . PAR-21MAA
(See Data Submittal Sheet)
Outdoor UnitCompressor . . . . . . . . . . . . . . . . . . . . . . . DC Inverter-driven ScrollMCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.4 + 0.4 F.L.A.Sound Pressure LevelCooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 dB(A)Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 dB(A) DiMenSiOnS inCHeS / MMW 37-3/8 / 950D 13 + 1-3/16 / 330 + 30H 53-1/8 / 1,350
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 lbs. / 121 kgRefrigerant Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R410ARefrigerant Pipe Size O.D. Gas Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5/8" / 15.88 mm Liquid Side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3/8" / 9.52 mmMax. Refrigerant Pipe Length. . . . . . . . . . . . . . . . . . . . . 245' / 75 mMax. Refrigerant Pipe Height Difference . . . . . . . . . . . . 100' / 30 mConnection Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Flared
SUbMittaL Data: pLa-a30ba & pUZ-Ha30nHa 30,000 btU/H CeiLing CaSSette Hyper Heat-pUMp SySteM
Remote Controller: PAR-21MAA
OptiOnaL aCCeSSOrieS indoor Unit• Multi-function Casement (PAC-SH53TM-E)• Air Outlet Shutter Plates (PAC-SH51SP-E) • Wireless Signal Receiver (PAR-SA9FA-E)• i-see Sensor Corner Panel (PAC-SA1ME-E)• High-efficiency (MERV 10) Filter (PAC-SH59KF-E)Outdoor Unit• M-NET Adapter (PAC-SF80MA-E)• Air Outlet Guide (PAC-SG59SG-E; two pieces are required)• Wind Baffle (WB-PA2; two pieces are required)
generaL FeatUreS• Innovative flash technology enables high heating capacity at lower outside temperatures• Exhibits 100% of rated heating capacity at 5ºF; 90% of rated heating capacity at -4ºF• Built-in drain lift mechanism for condensate removal; lifts up to 33-7/16 in.• Wide air flow pattern for better air distribution; independently adjustable vanes• Auto wave airflow in heating mode—unit independently cycles through horizontal and vertical positions for a more even heat distribution• Self-check function—integrated diagnostics• Hard-wired, wall-mounted, remote controller (PAR-21MAA)• Limited warranty: five years on parts and defects and seven years on
compressors
Dimensions: PLA-A30BA
14-27/3211-3/162-3/8
+5 0
(7.5
)
+35
-5
(160)(5
00)
(950
)
Floor
Min.94-1/2(2400)from floor
Entireperiphery
(36)(83)
(83)
(36) (500)
(950)
(597
)
(597)
( 1
58)
(ø175)(350)
(ø150)
(14-ø2.8)
(167
)(1
55)
(130
)(1
00)(90) (90)
(100) (100)
(35)
(17
)
+3/1
60
(190
)
(156
)(1
05)
(50~
70)
(140
)
(170
)
(377)(284)(60)
(24)
(187.5)(840)
(160)(1
60)
(20~
45)
to 1
-25/
32(8
60~
910)
(620
)
(605
)-3
/16
+1-
3/8
(90)
(150
)(1
60)
(7.5
)
(20 ~
45)
1-25
/32
Corner pocket
In case of wireless remote controllerIn case of standard grilleDrain lift mechanism cleanhole and Drain emergency drainage hole
For MA-Remote controllerterminal block
Emergency operation switch<Cooling>
Emergency operation switch<Heating>
Indoor unit
Ceiling
Cut out hole
Burring hole pitch3-ø1/8(3-ø2.8)Burring hole
Detail drawing of ventilation air intake connection
Burring hole14-ø1/8
Cut out hole
Burring hole pitch
Cut out hole
Detail connecting of branch duct (nominal 6"round or nominal 4 x 14" rectangular)
(77)3-1/32
(85)3-11/32
(298)11-3/411-1/16
(281)
(74)(80)(258)(241)2-29/323-5/3210-3/16
PLA-A36BAPLA-A42BA
PLA-A24BAPLA-A30BA
9-1/2
DCBA2
Refrigerant pipe ····ø15.88mmFlared connection····5/8
Refrigerant pipe ····ø12.7mmFlared connection····1/2
1
Refrigerant pipe ····ø6.35mmFlared connection····1/4
Refrigerant pipe ····ø9.52mmFlared connection····3/8
ModelsPLA-A12BAPLA-A18BA
Min.19-11/16(500)
Grille
Ceiling
Suspension bolt lower edge
Vane motor
Air intake grille
Air outlet hole
Air
outle
t hol
e
Auto vane(Air outlet)
Air
inta
ke h
ole
Air intake hole
GrilleCeiling
Keep 25/64(10)to 19/32(15)between unit ceiling and ceiling slab.
)(Connected the attachedflexible pipe or socket.
Drainpipe connected to1-1/4 in. O.D. PVC tube
Suspension bolt M10 or 3/8
Branch duct hole
Ventilation air intake hole
Branch ducthole
Cei
ling
hole
Sus
pens
ion
bolt
pitc
h
Suspension bolt pitch
Ceiling hole
(5/1
6)(5
/16)
23-1
3/16
24-1
3/32
DEFROST/STAND BY lampReceiverOperation lamp
For wiring replacement kit terminal block
6-5/16
6-5/16
1
2
3-15
/16
5-1/
8
13-25/32
3-17/32
3-15/16 3-15/16
3-17/32
* 6-9
/16
* 6-3
/32
ø5-29/32
ø6-7/8
19-11/16
19-1
1/16
23-1/2
M
M
M
M
3-17/641-27/64
37-3/8
3-17
/64
1-27
/64
37-3
/8
23-1
/2
1-15
/16~
2-3/
4
* 5-
1/2
* 6-
11/16
1-3/
8
11/1
6
* 4-
1/8
* 6-
9/64
* 7-
15/3
2 A
* B
6-5/
16
33-1
/16(
840)
5-29
/32
3-17
/32
C D
33-1/16
7-3/8
25/32 to 1-25/32(20~45)25/32 to 1-25/32(20~45) 33-27/32 to 35-13/16(860~910)
31-7/8(810)
25/3
2 to
33-2
7/32
to 3
5-13
/16
25/3
2
15/1
66-
5/16
Indoor unit/Outdoor unit connecting terminal block
ø4-29/32(ø125)
ø3-15/16(ø100)
6-7/
32 120˚
120˚
**
Note1. Use 1-1/4 in. O.D. (32) PVC TUBE.Drain lift mechanism is included.
2. Suspension bolt, use M10 or W3/8. (Field supplied)
3. Electrical box may be removed for service purposes.Make sure to include a little slack in the electrical wire for control/power wires connections.
4. The clearance between the grille and the unit is adjustable to compensatefor ceiling height.
5. For the installation of the optional high efficiency filter,the optional multi-functional casement is required.1) Add 5-5/16 (135mm) to the dimensions marked with an * in the figures 2) The high ef ficiency filter requires the multi-functional casement.
6. When installing the branch ducts, be sure to insulate adequately.Otherwise condensation may occur.
7. As for necessary installation/service space, please refer to the bottom left figure.