Post on 06-Feb-2018
transcript
Table of Contents
Preface and Conference Organization
Chapter 1: Advanced Manufacturing Technology
A Density-Based Potential Mission Risk Assessment Approach for Aerospace ProductsK. Mi and Y. Hu 3
A New Value Stream Mapping Technique Based on Material Flow, Information Flow andKnowledge FlowY.C. Pan, D. Liang, X.F. Ma and H.D. Wang 8
A Rapid Simulation and Optimization Study of Production LineX.F. Ma, D. Liang, Y.C. Pan and H.D. Wang 12
Research on Trusted ManufacturingX.M. Hu, Y.Y. Zhang, L. Zhao and L. Zhao 16
Software Framework for Advanced Error Troubleshooting in Flexible ManufacturingSystemL. Csokmai, O. Moldovan, I. Tarca and R. Tarca 21
Application of Cleaning Technology in the Remanufacturing for Loader's Axles andTransmission Box ComponentsR.S. Lu, B. Xu, H.T. Huang, G.S. Zhang and Z.X. Wu 25
The Study of Production Process System of New Multi-Feature Continuous Reel Soft PackTrademarksZ.L. Wang, B.G. He and Q.R. Tian 29
Tabu Search-Based Formation of Reconfigurable Manufacturing CellsJ.J. Du, G.X. Wang, Y. Yan and Q. Sang 34
Evaluation of Knowledge Resource Service Ability Based on Robust Projection Pursuit -Principal Component Analysis under Cloud Manufacturing EnvironmentN. Zhao and H.Y. Shao 42
Formation of High Aspect Ratio Macropore Array on N-Type SiliconG.Z. Wang, X.N. Li, F.Y. Yu, Y. Zhang, Y.Z. Liang, J. Chai, J.K. Yang and Q.D. Duanmu 47
Dynamic Error Modeling Research of On-Machine Measurement System Based onBayesian NetworkL.W. Yan and Q.B. He 52
Study on a Green Manufacturing Process Design SystemD.J. Zhong 57
Technology Research on the Fluidization Treatment of High-Titanium Slag to ManufactureSynthetic RutileL. Li and L.H. Zhou 62
Properties of Process Gas Combustion ProductsS. Honus, P. Bukowski and D. Juchelková 73
Parameters Research of Precise Straightening Process in Roller LevelerS. Li, Y.Q. Wang, G.Y. Liu and Y.H. Zhang 79
Multi-Directional Squeeze Casting Based on the Uniform Internal Structure of SolidifiedBodyC.L. Xu 83
Analysis of Multi-Directional Squeeze Casting Liquid Forging of Sewing Machine OilChassisC.L. Xu 87
Time-Pressure Switch Control for Fluid Dispensing Process Based on Self-Adaptive ModelC.P. Chen, T. Zhang and S.J. Guo 91
Chapter 2: Advanced Equipment Manufacture
The Design of Double Rotary Double Beam Self-Defense 20t Longmen CraneY.P. Wei and N. Wu 99
Aspects of Design and Manufacture of a Three-Dimensional Fibre Optic Laser DopplerProbe HeadN.A. Ahmed 103
The Shape Optimization Study of the Rolling Wheel of CNC Crushing MachineD.X. Zhang, W.L. Yang, Y.J. Ou, L.J. Zhang, S.W. Liu and W. Gao 114
Determination and Analysis of the External Load Change Characteristic of Loader SteeringCylinderL.C. Xu 118
Design Method of Offsetting Transmission Ratio of 6 Tons Truck CarL. Chang 122
Finite Element Analysis for Thermal Characteristics of High Speed Angular Contact BallBearingP. Wang, C.L. Lei, B.C. Zhou and W.P. Zhao 126
A Study of High-Speed Angular Contact Ball Bearing Thermo-Mechanical CouplingCharacteristicsC.L. Lei, Z.Y. Rui, B.C. Zhou and J.F. Fang 131
Application of Extenics Theory to Accuracy Evaluation of Machining CenterC. Liu and X.L. Bu 135
A Primary Design of the General Scheme on Modular Vertical LatheX.P. Liu and Y.C. Deng 140
The Research and Experimental Study of Fully Automatic CNC Grooving MachineM.F. Yin and C. Song 145
Study on the Design of Cantilever Crane in Wind TurbineG.H. Geng, S.W. Guo and X.J. Zhang 150
The Research and Development of Hydraulic Support Applied for Thin Coal SeamD.Y. Xie, X.Y. Zhao and A.Q. Li 154
Design and Manufacturing of Cylinder-Beam Integrated Hydraulic PressW.W. Zhang, X.S. Wang, S.J. Yuan and Z.R. Wang 157
Design and Optimization Based on the Spindle of Automatic Clamping LatheL.P. Liu, H.D. Li, C.C. Lin and Q.Q. Gao 162
A New Redundant Device for Monitoring Mechanical Press Slider Second FallX.B. Pan, R. Zhou, Y. Pan and G.P. Li 166
Design on Small Multi-Function Chassis Manipulator DeviceX.R. Lv, X.L. Lv and L.H. Zhang 172
Design and Manufacture of a Planetary Gearbox RigA.O. Bligh, N.A. Ahmed and Y.Y. Zheng 176
Optimization Design of Dryer Machinery in Tunnel Washing SystemX.R. Wang, W.H. Li,, B.J. Pan, S.J. Su, C. Gao and W.X. Tang 189
Research on Sewage Treatment by Combined Two-Phase ABR and SBRL. Jing and X.X. Wang 193
The Research of the Assembly Precision of CNC Machine Tools Considering the JointSurface CharacteristicsW.Y. Li, C. Lu and Z. Yang 198
Chapter 3: Fluid and Flow Engineering
Investigations of Energy Separation Effect in Vortex Tube for Natural GasesW.C. Wang, X.J. Fang, S.L. Liu and W.L. Sun 205
Parameter Computation of Equivalent Mechanical Models of Liquid Sloshing in SpacecraftContainerL.X. Zhang, Z.F. Bai, Y. Zhao and X.B. Cao 209
Optimization on the Structure of Ceramic Nozzles by FLUENT SimulationM.W. Ding, C.J. Fu and S.B. Yin 213
The Hinge Moment Optimization of Rudder Base on CFD Numerical SimulationN. Zhang and Y. Zhang 218
b Advanced Design and Manufacturing Technology III
Effects of Parameters Variation of Fractal Flow Path on the Emitter HydraulicPerformance with Path AnalysisP. Song, P.L. Yang, F.P. Xu and C.F. Zhou 222
The Numerical Simulation Research on Heat Transfer Enhancement of the Interpolation-Tubular Air Pre-Heater with Semi-Elliptic Cylinder Shell Vortex GeneratorD.F. Qing and Q.F. Ai 230
Study on Flow Distribution Relationship in Hydraulic SystemJ. Zhang, C.B. Fu, H.M. Tang, X.H. Li, C.R. Tang and W. Wang 235
Study on New Energy-Saving Excavator with Synthetic Positive Flow Control SystemH.J. Zhang, P.F. Yu and J.Z. Zhang 241
Effect of Turbulence Model to Simulation Accuracy of Wind Turbine BladeA.H. Yuan, Z.Z. Li, T.H. Cheng and Y.D. Shen 248
Effect of Fracture Parameters on Desorption Properties of ShalesK.K. Fan, R.Y. Sun, Z.C. Ma, Y.F. Zhang, Y. Wei and Z.Z. Zhang 252
Research the Internal Flow Field of Valve Stem LeakageY.T. An, R.J. Ma and Y. Wang 257
Modeling and Analysis of Full Hydraulic Pressure Drive System of the Wheel Loader Basedon AMEsimY. Yang and Q.L. Chen 261
Numerical Simulation of Laval NozzleY.D. Wang and H.G. Jia 266
Numerical Simulation of Shock Wave in Air Based on FCT MethodY. Li, X.B. Li, Y. Wang and W. Zhang 270
Numerical Analysis of Aerodynamic Noise in a High Parameter Pressure Reducing ValveL. Wei, M. Zhang, Z.J. Jin and L.L. Chen 274
Study of SO2 Detecting Using Non-Dispersive Infrared Based on Gas Filter CorrelationTechnologyZ.F. Dong, L. Shao, H.J. Yang, R. Yao and X. Yang 278
Chapter 4: Dynamic Systems and Analysis, Machinery Dynamics andDynamic Modelling
Dynamic Modeling and Motion Simulation for Wave GliderZ.F. Qi, W.X. Liu, L.J. Jia, Y.F. Qin and X.J. Sun 285
The Prediction and Analysis of Helicopter Rotor Rotation Noise in HoverD.W. Liu, P.L. Huang and J.Z. Ji 291
Recent Advances in Quasi-Zero-Stiffness Vibration Isolation SystemsF. Niu, L.S. Meng, W.J. Wu, J.G. Sun, W.H. Su, G. Meng and Z.S. Rao 295
Research on Modal Simulation and Experiment of a Radar Active Fixing-BoardS.W. Hou and Y.L. Wu 304
The Dynamic Simulation of Vertical Planetary Wheel Sand Reclamation Equipment Basedon ADAMSS. Li, Y.Q. Wang, Y.H. Zhang and G.Y. Liu 311
Simulation Analysis of the Impact on Gasoline Engine Power Performance by Optimizingthe Structure of Intake PortsH.B. Chen, S. Zhang, H.Z. Huang and Z.C. Yuan 315
Analysis & Study on Pneumatic Characteristics of Unidimensional Correction ProjectileBased on Resistance CircleJ. Qin and M.Y. Zhang 321
Research on Calculation Method for Polar Moment of Inertia of Spline ShaftX.J. Chai, B.M. Wang, K. Sun and C.B. Chen 326
The Dynamic Analyses of the Eccentric Cylinder Moving on the Inclined PlaneJ. Wei and W.P. Shi 330
Research on Vibration Isolation and Noise Attenuation Properties of Periodic LayeredStructuresZ.J. Wang, Z.Q. Jin and Y. Cong 335
Dynamic Adjustment Method of Mechanical Press Slide Height Based on Linear EncoderX.B. Pan, X.M. Shu and G.P. Li 340
Applied Mechanics and Materials Vols. 397-400 c
The Static Analysis of the Parallel Bars of the Crankshaft of a Mini Air Compressor onANSYSY.B. Wei and Z.Z. Qu 344
Study on Dynamics Characteristics of SINS Damping System in Shock EnvironmentX.Q. Tang, J.Q. Gao, L.B. Guo and H. Zhang 355
Nonlinear Study of Rotor-AMB System Subject to Multi-Parametric ExcitationsL. Li, Y.J. Han and Z.Y. Ren 359
Study on Torsion Vibration of Ship’s Complex ShafG. Liu 365
Dynamic Model of Automatic Transmission System of Tracked VehicleJ. Yi, S.S. Chen and D.Z. You 369
Research on Vibration Responses of Railway Steel Bridge Considering Welding ResidualStressJ. Liu, R.C. Zhang, L. Jiang, Z.S. He and D.M. Tan 374
Numerical Simulation on Flight Dynamic Characteristics of Elastic Wing Based on GustResponseW.H. Dong, C.L. Yang, Y.H. Li and H.G. Jia 378
Study on Balance Simulation of Milling Tool Handle in High Speed MachiningY.N. Xue, L. Xue and G.S. Su 384
Design and Performance Simulation of a Power-Integrated Transmission MechanismC. Mo, J.Q. Chen and F.C. Lan 388
Vibratory Stress Relief of Central Air-Conditioning EvaporatorX.W. Dong, J.H. Han, D. Ren, K. Mu, D.P. Liu and Y.L. Du 393
Analysis on Coupling Faults Induced Vibration of Hydropower UnitX. Liang, D.H. Liu, J.Z. Gui, Y.M. Xie and J.G. Huang 397
Simulation of Roll Stability of a Van in Cross-WindY. Wang and X.J. Hu 401
The Modal Analysis with Finite Element Method for the Cutting Arm of EBZ160RoadheaderZ.F. Dong, T.H. Wang, J. Liu, J.N. Huang and L.Y. Fang 405
A Constant Tension Control Device of Mechanical FeedbackZ.D. Wei, H.C. Xu and H. Su 409
Simulation of Heat Stress and Fatigue on Engine CaseC.H. Hou, H.L. Fan, Q. Sang and J.P. Lu 413
Vibration Analysis of Transmission Shafts Using Solid ModelsX.S. Yao 418
Dynamic Performance Analysis of a Smart Base Isolation System Based onMagnetorheological ElastomersZ. Qiao and J.G. Ding 422
Analysis on Torsional Stresses in Turbo-Generator Shafts due to Two-Phase Short-CircuitFaultY.J. Gu and J. Xu 427
A Quasi-Green Function Method for Free Vibration of Clamped Orthotropic ParallelogramThin Plates on Winkler FoundationS.Q. Li and H. Yuan 431
Load Distribution of Ball Screw with Contact Angle VariationS. Xu, Y.F. Sun and H. Shen 435
A Novel Dynamic Calibration Method for Dynamic Characteristics Testing ofHydrodynamic Journal BearingJ.N. Li and W. Chen 441
Dynamic Analysis of Less-Teeth Gear Transmission SystemD.S. Zhang, Z.L. Lv and J.J. Zhang 446
Study on the Global Bifurcation of Quasi-Zero-Stiffness SystemQ.C. Yang, L.H. Yang, Y.P. Chen and H.K. Lai 451
Binding Force Analysis of Multiple Pairs of Bars Space RCCR Mechanism without InertiaForceS. Zhuang, C. Cui, B. Han and K. Ouyang 457
d Advanced Design and Manufacturing Technology III
Prediction and Control of 32m Z-Propeller Tug Cabins Vibration and NoiseJ. Fang, H.B. Wen, Z.Z. Liu and J.M. Dong 461
The Optimal Design and Simulation Analysis of High-Speed Switching Valve Based onMagnetorheological FluidR.G. Feng, Z.Y. Wu, J.T. Wei, Y.J. Qin and T.C. Jia 465
Prediction on the Wear Life of Bearings for Planetary GearsJ. Zhang, Y.H. Liao and B. Huang 470
Analysis of Propeller Static Thrust Estimation MethodC.L. Yang, L. Zhou, N. Zhang and H.G. Jia 475
New Wind Turbine High-Speed Shaft Design and Simulation of Hydraulic Shock AbsorbersL.W. Yan, C.J. Ai and H. Xie 479
Research of Piezoelectric Cantilever Beam Diaphragm PumpH. Cai, L.L. Wang, J.S. Dong, Y. Yang and F. Lin 483
Research and Utilization of Downhole Dynamic Corrosion Test DeviceF. Gao, F.P. Li, Q. Wu and M.T. Jiang 489
Research on Simulation and Optimization of Dynamic Path Error of NC Machine ToolsL.Y. Li and J.D. Li 494
Analytical Calculation of Slotless Permanent Magnet Motor Based on Soft FerriteX.Y. Zhang, X.H. Wang, M.H. Li and X.Q. Zhang 501
Design and Dynamic Analysis of Magnetorheological Shock Absorber Based on thePiezoelectric TechnologyX.H. Wei, S.J. Yu, H. Nie, M. Zhang and Y.Z. Shao 505
Study of Modeling and Simulation on Driving Force Power Steering for Electric Vehiclewith In-Wheel-Motor-DriveC.X. Song, F. Xiao, L.Q. Jin, S.X. Song, J.H. Li and S.L. Peng 511
Bearing Looseness Fault Characteristics Analysis of Rotor System Based on IncrementalHarmonic Balance MethodG.L. Xiong, Q. Xiang and Q.S. Cao 517
Study on the Correct of Oil Temperature in Wet DCT GearshiftW. Sun, Z. Ning, J. Ma and G.Q. Liu 524
LOS Stabilization and Gyro Configuration Analysis for Roll-Pitch SeekerH. Liu, M.C. Zhu, B. Liu and H.G. Jia 530
Design of Midcourse Trajectory for Tactical Ballistic Missile Intercept on the Basis of ZeroEffort MissL.G. Li, W.X. Jing and C.S. Gao 536
Study on Dynamic Simulation of Buffering Mechanism with Liquid BagM. Zhang, R. Jiang, C. Yang and L. Cao 546
Wave Filtering of Ship Dynamic Positioning System Using Particle FilterW.J. Li, H.X. Xu and H. Feng 551
Chapter 5: Advanced Computer-Aided Design and ModellingTechnologies in Mechanical Engineering and Mechanisms
Simulation and Study on Ultimate Bearing Capacity of Stretcher Bracket for AeromedicalEvacuationJ.L. Wan, K. Lv, Q.J. Mao, Y.Y. Zhou and S.S. Yang 559
Modal Analysis and Dynamic Test of Steel Slag VehicleK.L. Mao 564
Finite Element Analysis for the Working Device of Rough Terrain ForkliftH.F. Yan, W.P. Wang, X.Y. Qi, H.X. Zhang, T. Tian and Y. He 568
Finite Element Analysis of Assembly Body of Conical PickX.Z. Pu 573
Modal Analysis and Optimization of Tricycle Vehicles Frame StructureH.H. Xu and C.D. Wan 577
Test Comparison of Damping Effect for Engine Damper Based on Rubber and MR FluidDamperC.L. Liang, J.W. Ma and F. Zha 581
Applied Mechanics and Materials Vols. 397-400 e
The Effect of Vehicles Steering Tilt Angle Impact Human ThoraxZ.H. Cai, F.C. Lan and J.Q. Chen 585
Finite Element Modeling and Analysis of Rolling Bearing Based on Explicit DynamicsJ. Cui, H.Q. Wang, F. Xiao and Z.Y. Dong 589
Characteristic Parameters of Cushion in High-Speed Train (CRH) Contribute to SeatPressure Distribution AnalysisW.Y. Wu, C.Q. Xue and L.D. Liu 593
Low-Wind-Drag Numerical Research on Fenders and Wheels of Car ModelX.J. Hu and Y.Y. Zhu 599
Research on the Simulation Method of the Belt Conveyor Correction DeviceX. Zhang, Y.L. Wang and J.B. Wang 603
Concurrent Engineering in the Application of Automobile Covering Parts MouldDevelopmentM. Fu, C.Y. Kong, B.B. Wang and M.H. Chen 607
Simulation of Luffing Mechanism of Lemniscate Type Crane with Boom DrivingK.Q. Li and C.X. Jiang 611
Method for Lumped Parameter Simulation of Digital Displacement Pumps/Motors Basedon CFDD.B. Roemer, P. Johansen, H.C. Pedersen and T.O. Andersen 615
The Research on Vibration Analysis of Blow-Down Wind Tunnel Pressure RegulatingValvesC.G. Yu, Z.B. Yu, Z.Z. Liu and H. Lai 621
The System Design and Parameterized Modeling of Juice Extractor ScrewY.Q. Zhao and X.F. Tan 625
Numerical Simulation to the Process of Damage Evolution of Defect CartilageQ.Q. Tian, J.D. Ye, X. Li, X.K. Wang, C.Q. Zhang and L.M. Dong 629
Finite Element Analysis of the Cylindrical Helical Torsional SpringH.Y. Li and X.L. Li 633
Study on the Three Degrees of Freedom Model of Leaf SpringB.M. Duan, H.X. Zhang, J.Z. Shi and M.Y. Wang 637
The Numerical Simulation Research of Three Dimensional Irregular Wave Based on WaveSpectrumY.F. Zan, Z.H. Dong, L. Song and W. Sun 643
Research of the Virtual Prototype of the Balanced Elliptical Motion Shale ShakerJ. Zhang 648
The Analytical Modeling and Finite Element Analysis of a Bridge-Type DisplacementAmplifierC.L. Shen, J.S. Dong and F.J. Tian 652
Based on NX NASTRAN Finite Element Analysis of Rotary Blade AxisX. Li, H.L. Wang and R.H. Zhang 656
The Establishing and Structural Analysis for Torque Shaft of the Shearer Based onInventor and AlgorJ. Zhang, X.X. Zhang and X.Y. Liu 662
Chapter 6: System Analysis and Industrial Engineering
The Green Mining Construction and Management of Daanshan Coal Mine in WesternBeijingJ. Shen, Z.C. Ren and W.D. Pan 671
Evaluation on Methods of Spatial Dependence TestT.X. Ren and L.M. Yang 675
Review of Human Factors in Maritime SystemD.F. Han and S. Ding 679
Empirical Research on the Rapid Growth of China's ODI: Based on Multinational PanelDataX.S. Gu and L.Y. Han 683
f Advanced Design and Manufacturing Technology III
A Study about Energy Consumption and Economic Growth in Qinghai Based on the Co-Integration AnalysisS.M. Li, P.J. Shi and Q. Zhou 688
Hazardous Materials Transportation by Road: Fuzzy-Theory-Based Routing DesignP.F. Li and M.X. Lang 696
Researching on the Mode of Selecting Key Village in Administrative VillagesG.R. Hong and B.F. Chen 700
Chapter 6: System Analysis and Industrial Engineering
Selecting Key Village by Quantitative and Qualitative MethodsG.R. Hong and Y.F. Wu 707
"Embedding" Updating Strategy Research of Urban Historic District — Taking SouthHistorical District of Nanjing as ExampleY. Shi, X.Y. Hu and J.Y. Yang 712
Construction Research on the Green Hydropower of Houziyan Hydropower StationS.G. Wu, M.T. Zhou, F. Chen and H. Hu 717
The Quantitative Analysis about the Impact on Transport Demands by the IndustrialStructureH.H. Qin, X.S. Jiang and Z.Y. Nie 722
Tail Dependence Structure between Carbon Emission Allowances Returns Based onCopulasD.D. Zhuang 726
Feasibility Analysis of and Recommendations for Establishment of a Greenhouse GasEmission Reporting System on China's Industrial EnterprisesJ.H. Chen, W. Bao and L. Chen 731
A Research on the Systematic Structure of Green Manufacturing and some Major Problemsin its ImplementationQ. Wang 735
Optimization Scheme Selection on Bamboo-Wood Pallet Technological ProcessY. Pang and Z.P. Zhu 739
Intrinsically 3-Linked Graph with Knotted ComponentsQ.P. Ren and G.H. Wang 746
The New Method Exploration and Research on Product Carbon Footprint CalculationX.D. Dong 750
Performance Evaluation of Vehicle Electronic Stability Program Based on PsychologicalMethodZ.H. Gao, Z.Y. Guo, S.H. Zhou, K. Ma and H. Zhao 754
Equivalence of TransducerW. Gong and J. Shi 761
Theoretical Analysis of a Acoupled Fiber Ring ResonatorX.M. Zhang, Y.K. Ci, J.L. Yao and J.L. Wang 765
Chapter 7: Innovative Design Methodology and Product Design
Bionics Design of Stubble Blade Based on the Digging Claw of Mole CricketW.G. Zhu and C. Chen 775
Orthogonal Testing Optimum Design in Radial Electrodynamic Magnetic BearingsS.Q. Tang, D.Y. Yang and Q.Q. Bai 779
A Conceptual Model of Flapping-Wing Mechanism Inspired from the Results of NumericalStudyX.W. Zhang, C. Wang and H. Liu 783
Research on Modern Product Design Method and Procedure Based on the Concept of FullLife CycleX.W. Guo, P. Guan and Q.S. Xie 789
Research on Product Design Based on the Effect Factor of Product Whole Life CycleX.Y. Xu, P. Guan and X.W. Guo 794
Applied Mechanics and Materials Vols. 397-400 g
A Product Concept Method for Industrial Design Based on Basic-Element ModelL.L. Liu and C.Q. Xue 798
Research on the Parametric Design of Simple Sofa with RhinoScriptL. Wei, S. Liu, Y. Yuan and Y.Q. Wang 802
The Design of Finite Element Application Framework Based Design PatternsM.W. He 806
Visual Perceptions of Materials in Emotional User Experience DesignH.C. Xia and S.Y. Zhang 812
Optimal Design of Gears by Means of Genetic Algorithm and Neural NetworkY.G. Li, and Y.M. Ma 816
A Designing Method of Variable Topology-Transformable SpacecraftX. Ning and X.K. Yue 821
Research on Formulation Method of Urban Modal Driving Cycles of Regenerative BrakingS.P. Zhang, X. Huang and G.L. Wang 826
Self-Adapting Function Principle and Creative Design of BFT TypeH.L. Luo, L.Y. Zhang and Q. Yuan 830
Design of Porous Restriction Aerostatic Guideway for Form Measuring InstrumentZ.Q. Li, H.C. Yu, H.Y. Zhao, G.Q. Zhang and H.H. Li 833
An Evaluation System of Maintainability of the Civil Aircraft Based on Virtual RealityX.D. Wu, H. Liu, S. Mo and Z. Wu 838
New Methods of Reliability EngineeringY.L. Cui, C.M. He and J.W. Wang 842
Modeling Present Worth of Product Quality Loss of STB Characteristic Based on ServiceLife DistributionY.M. Zhao, D.S. Liu, Z.J. Wen and T. Liu 846
Exploration on the Packaging Designs Idea of Motion in QuiescenceY.G. Yang and W.C. Xu 852
The Life Cycle Management and Evaluation of Equipment Maintenance QualityZ. Zhang, J. Chen, B. Peng and Y.G. Zuo 856
Artistic Techniques for Developing Creativity in DesignF.J. Hassan and X.Y. Bian 862
Research on Multiple Environment over Stress TestingY.L. Cui, S.X. Zhang and C.M. He 866
A New Piezoelectric Generator Based on StairsZ.W. Jiang, Z. Yin, H. Li and J. Zhang 870
Sustainable Innovation Design for Buckle Ring Machine of Button BatteryH. Jin, H.X. Guo, G.Z. Cao and S. Wei 874
An Analysis of Product Design Based on Traditional Chinese CultureL.L. Liu and K. Chang 878
Digital Design of Automotive Wire-HarnessY. Liu, S.R. Yuan, N. Zhou and X.Y. Dang 882
Innovative Design of Injection Mold Based on Design around PatentH.L. Wang 889
Study on the Application of the Unisex Design Element in Menswear DesignS.C. Chen and Y.W. Wu 893
Strategies for the Design of Ice and Snow Landscape of Urban Residential District in theCold RegionsZ.X. Yang, T. Ma and J. Huang 897
Higher Dimension Modules Incurred Mechanism Structure VariationL.P. Zhang, G.B. Pang, M.J. Zhou and F.L. Bu 903
Study on the Design of Outdoor Furniture Made of Recombinant BambooX. Liu and Z.F. Zhang 907
Study on the Relationships between New Paper Surface Efficiency and Printing QualityParametersY.G. Yang, F.P. Liu and Q.Z. Gao 911
Working Principle and Mechanics Analysis of Circular Bundling MachineJ. Wei and W.P. Shi 915
h Advanced Design and Manufacturing Technology III
A Design of Ginkgo CleanerL.H. Zhang, T.T. Liu and G.H. Li 919
The Reformation Design of the Qidashan Semi-Mobile Crusher StationX.Y. Wang and X.G. Yu 924
Research on Technologies of Green Design and Manufactuirng for Toys DesignP. Guan, X.Y. Xu and X.W. Guo 928
Design of Single Star Simulator Based on LED Light SourceX.J. Gan, X.H. Gao, Y. Chen and J. Li 932
Design of pH Meter Based on msp430J.J. Ding, J. Wang, C. Sun, Y.Q. Liu, J.Y. Shao and J.L. Xue 936
Research on Methodology of Module Division in Fractionated SpacecraftX. Ning, Y.F. Li and X.K. Yue 943
Simulation with Aspen Plus and Performance Analysis of LT-MED Seawater DesalinationSystemZ.Q. Ma, S.H. Huo and M. Su 948
Structural Design and Parameters Optimization of Rice Seed-Metering DeviceJ. Ma, X.L. Lei and R.C. Ma 957
Product Module Division Method Based Degree of ModularityY.H. Chen and Y.P. Chen 966
Manufacture of an Unmanned Aerial Vehicle (UAV) for Advanced Project Design Using 3DPrinting TechnologyN.A. Ahmed and J.R. Page 970
A Novel RFID-Based Thermal Convection Type Inclinometer with Non-Floating Structureand Hemi-Cylindrical ChamberJ.M. Lin and C.H. Lin 981
Chapter 8: Intelligent Optimization Design and Reverse Engineering
Transmission Ratio Optimization of Electric Vehicle PowertrainY.M. Wang, C.Q. Du, X.N. Li and F.W. Yan 987
Measurement Technique Based on the Three-Dimensional White-Light ScannerX.D. Xie, X.K. Liu and J.T. Cheng 993
Motor Shell Temperature Prediction Based on ARIMAM.T. Huang and X.M. Gao 997
Research on Enable Advanced Technologies for Swarm ConstructionY. Yang, Y. An and Y.A. Yang 1001
ADACD-Based Novel Optimal Model Identification Scheme for MIMO Discrete NonlinearSystemsM.X. Liang 1006
The Study of Induction Setter Based on Low Density Parity Check Coding MethodF.X. Liu, L.M. Wang, F. Zhang and X.M. Xu 1010
Correction of the Asymmetrical Projection for Accurate Camera Calibration Using Co-Planar Circular FeatureX.L. Meng, W.T. He, X.Q. Che and C. Zhao 1016
Enhanced Two-Point Exponential Approximation for Structural OptimizationT.T. Chung, Q.H. Jiang and J.R. Zhu 1021
Hardware Design of the Agricultural Greenhouse Internet of Things Monitor TerminalL. Wu, X.Y. Jiang and Y. Xie 1025
Research on Genetic Algorithm in Mold Optimization DesignX. Chen and B.S. Zhao 1030
Optimization Design Study of Loader Working Mechanism Based on MATLAB ComplexMethodH.L. Yang, T.Q. Zhang and G.R. Gao 1034
Prediction of the Metro Section Passenger Flow Based on Time-Space CharacteristicJ. Jin, Y.H. Wang and M. Li 1038
The Optimization of Piston Groove Diameter Based on ABAQUSS.G. Qu, W.L. Li and B. Li 1045
Applied Mechanics and Materials Vols. 397-400 i
Research on Object-Oriented System Model Based on FeatureK.W. Li, Q. Li and X.H. Niu 1050
Analysis on Knowledge Sharing Risks in Knowledge Chain Based on Matter-ElementC.L. Yang 1055
Quantitative Analysis of the Defect Dimension for Fracture Surface of Fracture SplittingConnecting RodS.Q. Kou, H.Y. Yang, S.H. Yang and B.J. Lin 1059
Boiler Combustion Control System Optimization StrategyY. Zhang, Y. Yao and T. Luan 1064
Research on the Discretization of STL Model in the CNC Incremental FormingH. Zhu, J. Ju and W. Zhang 1069
Research on Assembly Optimization of Hull Section Based on the Genetic AlgorithmsW.J. Xu, L.K. Wang and Z.F. Zhang 1073
Risk Analysis on Grain Quality in the Drying ProcessX.Y. Wu, Y. Fu and Y. Xu 1078
Highly Anti-Noise and Adaptive B-Spline Curve Reconstruction Based on ICT Slice ImagesG.S. Liu and B.L. Li 1083
Application of Reverse Design in Wine Packaging Container DesignL.Y. Zhang, H.L. Luo, G. Xu and Y. Zhou 1088
B-Spline Curve Approximation Using Feature PointsX.G. Cheng 1093
The Research of Adaptive Robust Predictive Current Control Algorithm of PermanentMagnet Synchronous MotorsL.D. Lin and X.B. Han 1099
Load Prediction of RBF Neural Network Considering Weather FactorsR.R. Wei, Z.Z. Wei, H.B. Yang and J.D. Jiang 1103
Several Non-Rearranged Dynamic Multicast Routing AlgorithmsY.F. Dai and N.F. Li 1107
Reactive Power Compensation of Oilfield Distribution Systems Based on Tabu SearchAlgorithmX.M. Wu, W.H. Fei, X.M. Xiang and W.J. Wang 1113
Parallel Ant Colony Algorithm Based on Award-Punishment Mechanism and itsApplication on Wireless Sensor Network RoutingH. Yang 1117
Research on Re-Use Reverse Logistics Network of Disused Electric Appliances Based onElection Campaign AlgorithmQ.H. Xie, X.W. Zhang, W.G. Lv, S.Y. Cheng, H.X. Huang and S.D. Cai 1121
Optimal Design of CNC Crushing Machine Steady Based on Genetic AlgorithmD.X. Zhang, M.J. Han, Y.J. Ou, G.Q. Wang, G.Q. Hao and J.F. Huang 1129
Study on Common Fault of Wind TurbineC.F. Yan and R.H. Hu 1133
Application of an Improved Internal Model Controller Based on the Particle SwarmOptimization in Network Control SystemW. Chen, W.B. Wang, Z.K. Zhao and Z.Y. Yan 1137
Fault Knowledge Acquisition of Electronic EquipmentF.H. Zou, H. Zhang, G.B. Ding and D. Li 1145
A Nearly Optimal Peak Reduction Tone Set Selection AlgorithmJ.Q. Zheng and Y.J. Wang 1148
Chapter 9: Mechatronics, Automation and Control, DetectionTechnologies
Adaptive Sliding Mode Control of the Linear Drive SystemW.B. Wang 1155
Adaptive Control for Aircraft Anti-Skid Braking SystemF.Y. Li and Z.X. Jiao 1160
j Advanced Design and Manufacturing Technology III
Research on Intelligent Control System of High Speed and High Precision Filling DiscMachineY.K. Duan and J.F. Ni 1164
Study of Topology and Control Strategy of the Bidirectional Energy Storage ConverterBased on Three-LevelH.W. Tang, X.K. Chen and Y.X. Gao 1169
Testing System of Needle Selectors for Jacquard Knitting MachinesJ. Ma, X.F. Zha, H.B. Tao and J.F. Ni 1174
Study of Topology and Control Strategy of the Novel Bi-Directional Lithium BatteryChargerX.K. Chen and H.F. Zhu 1178
Drive Control of a Class of Scan SystemsC.X. Wang, M.H. Liu and N. Cai 1184
Research on Reliability of Electromechanical System Based on the Competition ModeW. Han, S.J. Sun, Y. Liu and Q. Liu 1188
Developing and Research on Open Motion Controller Based on PCG.W. Cui, R.L. Chang and J. Han 1192
Systematic Design of Electronic Steering Wheel in Steer-by-Wire of Engineering VehicleA.M. Wang and M. Tang 1196
Developing and Research on Liquid Level Control System of Double-TankR.L. Chang, J. Han and G.W. Cui 1200
Rapid Prototyping Design for In-Wheel Motor ControllerC.X. Song, S.L. Peng, L.Q. Jin, J.H. Li, S.X. Song and Z.A. Zheng 1204
The Influence of Pole-Slot Match on Magnetomotive Force with Concentrated Fractional-Slot WindingM. Si and Y.L. Yang 1209
Research on Integrated Control System of the Gas Pressure in Coke OvenX. Bai, D.L. Guan and C. Rui 1214
Progress in Research for Pipe Inner Diameter Detection Technology Based on LaserJ.S. Cao, K.L. Li, R.Q. Li, Y.D. Wei, G.J. Li and L. Zhang 1220
Step Motor Control Based on FPGAJ. Zhu and Y. Chen 1226
Research on the New Type of 12kV Inflatable Vacuum Circuit BreakerH.Y. Wang, E.Y. Dong, G.X. Yin, M.W. Liu and X.P. Zeng 1230
Research on Fuzzy Control in Vacuum Heat Treatment Furnace Temperature ControlSystemX.Y. Wang and Z.W. Zhou 1236
Modeling and Simulation of Vector Control System for Asynchronous MotorJ. Rong, Y.J. Ding and X. Chen 1241
Optimization of the Hydraulic Control System Utilizing BP Neural Network ControlStrategy Based on Genetic AlgorithmY.Y. Feng, N.M. Hui, Z.A. Luo and D.H. Zhang 1245
Design and Implementation of Vehicle Attitude Detection and 3D Dynamic Display SystemL. Zhang, Q.S. Wu and R. Gao 1253
Electromechanical Actuator Control System Development Using Rapid Prototyping MethodJ.B. Zhang 1258
Study on Temperature Control System of Film Laminating MachineL.M. Guan, J.X. Tian, C. Lu and W. Zhang 1263
Automation Control System of Pharmaceutical Factory Based on Wireless Sensor NetworkQ.F. Shang and L. Zhang 1271
Synchronization of a New Fractional Order Hyperchaotic System with Activation FeedbackControlW.W. Zhang and D.Y. Chen 1278
Bearing Condition Recognition Based on Kernel Principal Component Analysis and GeneticProgrammingW.B. Liu, Y.X. He, H.Q. Wang and J.F. Yang 1282
Applied Mechanics and Materials Vols. 397-400 k
Design and Simulation of the Self-Tune Fuzzy Logic PID Controller for VAV Air ConditionSystemG.C. Zhang 1286
Design of Intelligent Home Control System Based on a Variety of NetworkD.H. Chen, S. Ke, J.Q. Chen and X. Chen 1291
The Optimization of the PID Controller Using the Least Squares Method and the ImprovedLbest PSO AlgorithmC.G. Yang, Z.J. Yang, F. Chen, Y. Zhu, Y.N. Kan and Z.T. Zheng 1296
Research on Fuzzy PID Control for Power-Train MR Mount SystemD.Y. Pan, X. Gao, C.G. Xia and H. Cai 1304
Adaptive Levitation Control Based on Feedback LinearizationL.X. Li and Z.Q. Jin 1309
The Design for the Hardware of Analog Controlling ModuleH. Dai, L.T. Xu and W.P. Chang 1314
Design of Temperature Control System in IncubatorS.W. Chen 1317
A Simple SOM Neural Network Based Fault Detection Model for Fault Diagnosis of RollingBearingsZ.C. Li 1321
Study on Optimization Control Method of the Pickling ProcessD.K. He, W. Qin, T.S. Liu and Q.Y. Yuan 1326
Data-Based Research on Predictive Control of Multiple Mismatched Model ParametersD.K. He, J.Q. Xin, W.L. Yuan and Q.Y. Yuan 1331
The Study of Fuzzy Control Algorithm in a Duct Active Noise Control SystemX.J. Meng, J. Wang and Y.C. Wang 1337
Output Feedback Control for a Class of Uncertain Fuzzy System by Controller SwitchingH.H. Lv and H. Yang 1341
Finite-Time Chaos Control of Lorenz Chaotic System Based on the Passive ControlTeachniqueF. Liu 1345
Vehicle Stability Analyse with Electronic Power Steering Based on Yaw Rate FeedbackH.F. Song and W.W. Yang 1351
Strapdown Optical Seeker Guidance Instructions Extraction and System StabilityY. Zhang 1357
A New PLS and Bayesian Classification Based On-Line Outlier Detection MethodT.B. Wu, Y. Cheng, Z.K. Hu, W.P. Xie and Y.L. Liu 1362
Path Following Control of a Mobile Robot Using Contractive Model Predictive ControlK. Kanjanawanishkul 1366
Model Free Control of the Refrigeration System Based on Minimum Stable SuperheatB.H. Cheng, A.G. Wu and Y.W. You 1373
Research on Pantograph Active Control Strategy for Reducing the Pantograph–CatenaryWearC.X. Li and L. Dong 1378
Analysis of DAS and ATWS Mitigation System in Nuclear Power PlantW.Y. Yao and J. Bai 1383
The Parameter of Fuzzy Self-Tuning PID Controller Realized Based on VHDLQ. Wu, S.H. Ma and Z.Y. Cai 1387
Chapter 9: Mechatronics, Automation and Control, DetectionTechnologies
The Research of Permanent Magnet Synchronous Motor Predictive Current ControlAlgorithmL.D. Lin and P.J. Ren 1393
Control Strategy of PMSG in Variable Speed Wind Power SystemH.L. Li 1398
l Advanced Design and Manufacturing Technology III
The Study of Detection System of Two-Wire Flowmeter Based on Virtual InstrumentTechnologyF.X. Liu, L.M. Wang and L.X. Deng 1403
Study on Mechanical Braking System Development Method and Validation for ElectricVehiclesX.M. Huang and G.B. Ning 1407
Real-Time Auto-Light System for High-Speed CameraH. Yang and M.H. Liang 1418
A Power-Control-Based WSN Boundary Detection Algorithm for Agricultural EnvironmentMornitoringX.M. Xu, G.F. Feng, M. Chen and Y. Zhang 1422
Modeling and Control with Hysteresis of Piezoelectric Smart Materials ActuatorsY.M. Liu, Z. Chen, X.Z. Zhuang and Z.H. Liu 1426
An Energy-Saving Control System to Street Lamp Based on Sensor NetworksX.G. Li, P.P. Xiao and J. Zhu 1430
Fault-Tolerant Control System Design of UAV Based on Dissimilar RedundancyZ. Duan, D.H. Qiu and J.Z. Gao 1434
Intelligent Control of a Cart and Pole SystemH.L. Jia, Q. Liu and F. Du 1438
Design Higher Order Sliding Mode Controller for a Class of SISO Uncertain NonlinearSystemJ. Liu, G. Ding and Z.S. Zhao 1442
Design and Implementation of Fall Detection System Based on ZigBeeY. Zhang, G. Tan, Y. Luo and Y. Li 1446
Chapter 10: Industrial Robotics and Machine Vision, Navigation andGPS Technology
A Method of Line Structured Light Vision System Calibration Based on Stereo VisionY.B. Liu, B. Liu and J.Y. Lin 1453
Steps and Stairs-Climbing Capability Analysis of Six-Tracks Robot with Four Swing ArmsY.W. Li, S.R. Ge, X. Wang and H.B. Wang 1459
Design of Automatic Tracking System Based on FPGA and Binocular VisionW. Song, Y.X. Chen, L.J. Zhang and S.Y. Qin 1469
The Design of the Intelligent EOD Manipulator with Five DOFD.D. Liang 1473
Robust Adaptive Control for Robotic Manipulators Based on RBFNNB.S. Xing and W.H. Zhang 1477
Development of Quality Detecting System for Micro Holes by ECM Based on MachineVision TechnologyY. Liu, L.S. Zhu and Q.J. Xiong 1482
Robotic Curve-Shaped Seam Tracking System Using Vision SensorF.X. Gao 1486
Fuzzy Control for Underactuated ManipulatorQ.X. Xia, Y.Q. Yu and Q.B. Liu 1490
A Novel Texture Spectrum DescriptorS.H. Yan, X.T. Huang and Y. Liu 1494
True Color Image Enhanced by Wavelet Illumination-Reflection ModelJ. Xiong and L. Lu 1500
An Algorithm to Transform Tolerance-Control Solutions of Interval Linear EquationsL. Tian and W. Li 1506
Design of Multi-Stage Optimal Arbitrary Time-Delay FilterK.P. Liu, J.P. Zeng, M. Yang and C.H. Jiang 1510
Forward Position Analysis and Error Modeling of the 2UPS-RPU Parallel ManipulatorY.W. Niu, S.H. Wen and Z.Y. Feng 1515
Application of Image Processing Technology in Welds Ultrasonic TestingJ. He, L.C. Zhu and K.C. Wang 1519
Applied Mechanics and Materials Vols. 397-400 m
A New Automatic Focusing Algorithm and its Application on Vision Measuring MachineH.D. Zou and H.X. Wang 1523
Adjacency Matrix Based Analysis on a Novel Metamorphic Manual Operation SugarcaneLoaderD.Z. Gao, G.W. Cai, H. Shi and Y.C. Pan 1529
Design and Topological Analysis of a New Manual Operation Sugarcane Loader withMetamorphic FunctionD.Z. Gao, G.W. Cai, H. Shi and Y.C. Pan 1534
Desalinization Water Treatment Control System Design Based on Mitsubishi PLCL. Yu, J.R. Ning and X. Li 1539
Design and Analysis of a Micro-Motion Platform Based on Flexible MechanismY.M. Yu 1543
Binocular Stereo Vision Calibration System Implementation of Grid Strain Measurement inSheet FormingH.Y. Xiang, B.A. Han, Z. Li and J.J. Huang 1547
Modelling and Simulation of Forward Kinematics for Planar 3-DOF Parallel Robot Basedon SimulinkX.Z. Dang, L.S. Zhou, L.P. Liao and D. Liang 1552
Study on Dynamic Characteristics of Parallel Robot with 2-DOFM.Y. Chen, H.B. Xin, Q.L. Li, Y.F. Xin, D.Q. Cui, L. Liu and T. Wang 1558
Build for Motion Control System of Planar Five-Bar Parallel MechanismD.Y. Zhao, H.B. Xin, Q.L. Li, D.Q. Cui, Y.F. Xin, L. Liu and T. Wang 1563
The Structural Design and Kinematic Analysis of Palletizing RobotY.G. Zhao, H. Sun and T.C. Cai 1568
The Control of Fuel System for Combustion Piston Type Hopping RobotS. Saifullah, M.S. Yuan and S. Bdran 1574
Obstacle Performance of Track Robot with Passive Rocker Based on RecurdynM.L. Liu, J. Zhang and K. Li 1580
The Design of Stereo Vision Autonomic Navigation Robot Based on SOCH.F. Wang, X.M. Long and X.L. Cui 1589
Ferrying Performance Analysis of a New Type All-Terrain Tracked Water CarrierC.Q. Xu, T.M. Li, G.Z. Jia and R.L. Gao 1593
Neural Network Aided GPS/INS Integration for UAV NavigationQ.J. Meng 1598
Research on Precise Positioning Technology of Mine Locomotive Unmanned SystemsB. Ge and S.X. Zhang 1602
An Improved Adaptive Algorithm for INS/GPS SystemL.D. Wang, Y. Zhao and N. Zhang 1606
An Optimizing Evaluation of Estimation Algorithm about the Fault Detection andExclusion in the WAASR.B. Zhao, R. Li, Z.G. Huang and B. Shao 1611
Chapter 11: Sensor Technologies
Design and Analysis of a New Electrode for Micro-Structure Gas SensorC.B. Liu, K. Bi and X.B. Zhang 1617
The Model Used to Pretect Wetlands Based on Zigbee TechnologyJ.S. Xiao, Y.G. Dai and T. Xu 1621
Design and Analysis of a Low-Range Torque SensorL.L. Wang, J.J. Sun, Q. Mei, H. Cai, Q.C. Liu and J.S. Dong 1627
Design of the Angular Displacement Sensor Based on Magnetoresistive TechnologyY. Lou and X.Y. Zhao 1633
Design of Large-Stroke Linear Displacement Sensor with High-Precision Based on SS495A1TechnologyY. Lou and X.Y. Zhao 1638
Research on Modulation Multiplexing System and Technique Employing Tilted GratingH.B. Wang and Z.Q. Li 1643
n Advanced Design and Manufacturing Technology III
Chapter 12: Measurement and Monitoring Technologies
Design of Multiple Bus Configuration Monitoring System Based on OPC TechnologyL. Yu and J.M. Wang 1651
Study on Monitoring and Control System of Vehicle-Mounted Rig Based on CAN BusD. Fan, Y.S. Weng and H.L. Tian 1655
A Size-Shifting Measuring Method for Multi-Diameter Shaft GrindingP. Zheng, L.N. Zhang and Z.Y. Zhang 1661
The Research on Overpass Water Depth Monitoring Sandbox Based on Internet of ThingsH.H. Shi, T. Chen, G.D. Wang and Y. Liu 1665
Development and Application of Die Swell Data Gathering System Based on Multi-Functionand all-Electric RheometerX.G. Li, Y.J. Liu, F. Zhao, Y.G. Huang, Y. Chen and W.Y. Liu 1669
Design and Implementation of Large Computer Room Environment Intelligent MonitoringSystem Based on ZigbeeX.C. Zhao, J.Q. Li, J. Liu, Q. Shi and L. Sun 1673
Research on the Measurement Error of Portable Braking Performance TesterC. Wei and M.X. Nie 1677
Evaluation of Equipment Comfort in Data Centers by Fuzzy LogicC.G. Yu and G.X. Liu 1681
Measuring Method for the Signal Distortion of Axial Thrust and Mechanical VibrationPlatformS.S. Wu, X.M. Lin and Z.W. Lu 1685
An Improved Algorithm Based on Incremental Insertion in Delaunay TriangulationJ.H. Xi and S.C. Zuo 1691
The Calibration of Binocular Stereo Measurement System Based on a Coded ModelH.M. Chen and H. Zhang 1695
Development of Motor and Controller's Engineering Measurement SystemX.G. Ding, S.F. Lin and Z.K. Chen 1700
Research on Highway Early Age Freezing Information Collection SystemL. Xie, B.L. Zhu, T. Wang and L. Bian 1705
A Depth Measurement Method Using Two Structured Light Binary PatternsW.Z. Zhang, P.C. Yang, Z.M. Guo, G.H. Ju and B. Lin 1709
The Principle and Calibration of the Third Gear Flow-MeterJ. Zhang, M.M. Niu, H.M. Tang, X.H. Li and C.R. Tang 1713
Design on Monitoring System of Fire Disaster Based on Zigbee CC2530B. Chang, X.R. Zhang and L.H. Li 1718
Sensing Characteristics of Sampled Fiber Bragg Grating about Temperature and StrainD.D. Zhu, Y.P. Wang, W. Liu, D.R. Meng, X.Z. Hu and J. Song 1723
A Novel Integrated Portable Elasticity Measurement SystemH.C. Chang, C.C. Chiang, S.S. Hung, S.L. Lin, S.C. Liao and C.H. Chen 1728
An Optical Centrifugal-and-Pneumatic Controlled Microfluidic System for Sensing Real-Time Biochemical ReactionsH.C. Chang, Y.H. Chen, S.L. Lin and S.S. Hung 1733
A Novel Alignment Method for Collimator Based on Laser Differential Confocal TechniqueF. Li, L. Li, B.Y. Hong and W.L. Liu 1738
Design and Implementation of Gas Detector Position Computer System Based on ARML. Shi, H. Zhao and H. Cai 1744
Measuring Routine Parameters of Wine by ATR-MIR SpectroscopyZ.H. He, X.R. Duan and Z.H. Ma 1749
The Design and Implementation of Monitoring System of Flue-Cured Tobacco Barn Basedon ARM7J.H. Liu, Y.T. He and Y.H. Peng 1753
Development of Timing Component for Angular Distortion Measurement SystemM.H. Zhang and Y.Y. Zhang 1759
Applied Mechanics and Materials Vols. 397-400 o
Application of Multithreading Technology in the Real-Time Measurement SystemM.H. Zhang and Y.Y. Zhang 1763
Thermal Characteristics of High-Power LED Packages with Dissipation FilmC.Y. Hsu and Y.L. Lin 1767
A STEP-NC Compatible on-Machine Measurement System with Automated Correlation ofInspection DataP. Lei and L.Y. Zheng 1772
Chapter 13: Power, Energy, Microelectronic Technology and EmbeddedSystem
Research of Bearing Raceway Ultra-Lapping Unmanned Manufacturing System Based onEmbedded TechnologyZ.X. Huang, C.G. Li, B. Li and H. Luo 1781
Design of Remote Control Equipment Based on Industrial EthernetY.H. Yang, B.Y. Zhang, N. Zhang and C. Gao 1785
New Bank Electronic Combination Lock SystemF.J. Chang and C. Wang 1790
Characteristics Analysis and Simulation Testing on Modular Multilevel Converter VSC-HVDC Based on RTDSJ.G. Chen, C.B. Yu, T.T. Sun and K.J. Ou 1794
Three Carrier PWM Control of Improved Z-Source InverterH.G. Zhang, W.W. An, X.B. Li and J.J. Li 1800
Research on Dual PWM Converter for VSCF Brushless Doubly-Fed Wind PowerGeneratorL.C. Zhu, J. He, Y.J. Yang, X.Y. Su and F.Y. Li 1804
Development of Back-to-Back Flexible HVDC Prototype Based on MMCC. Feng, D.L. Wang and J. Li 1808
A Review of Applying Customer Power Technology to Improve Transient Power QualityH.X. Shi, Y. He and L. Zhao 1814
Design and Application of High-Power LED Drive and Control CircuitsC.W. Li, J. Zhang and H.Y. Ou 1822
Study on AES and its Efficient Implementation on STM32F103 ProcessorX.H. Zhang and G.N. Liu 1828
Design of Remote Control System for Smart Home Based on Z-WaveC. Gao, M.Y. Jiang, N. Zhang, F.L. Huang and Y.L. Li 1833
Random Yield Model in Integrated Circuit DesignX.M. Chen, W.Q. Wu and S.S. Li 1837
Design of a K Band MEMS Switch with CPW Defected Ground StructureZ.L. Deng, C.H. Chen, S. Fan, H. Gong and X.F. Sun 1844
Design of Sampled Fiber Bragg Grating Comb FilterD.D. Zhu, J. Song, X.Z. Hu and Y.Y. Zhang 1850
A New Microprocessor Protection Scheme Based on Digital Signal ProcessorJ.H. Lian 1854
Modeling and Simulation of the Auxiliary Power System in Extended Range ElectricVehicleL.S. Chen, X.L. Wang, X.E. Huang, P. Gan and W. Cheng 1858
Research on Grid-Connected Photovoltaic Generation System Based on Novel MPPTH.M. Wu and C. Cao 1863
Study of a Multi Objective Reactive Power Compensation Device Considering FaultCurrent LimitingH.M. Wu and W.T. Hui 1868
Evaluation of Silicon Nitride MIM Capacitors for MMIC ApplicationsW.S. Feng and Y.J. Chen 1873
A Novel Pilot Protection for HVDC Transmission Lines Based on Model Error FunctionD. Li and X.F. Jin 1878
p Advanced Design and Manufacturing Technology III
The Optimization of Power Smoothing Control Strategy for Wind Farm Based on FlywheelEnergy Storage DeviceY. Huang, Y.H. Yuan and G.M. Zhang 1883
Compact DC-DC Power Design in Half-Bridge IGBT DriverQ.Y. Wang, Y. Liu, P. Xu and D.C. Luo 1888
ATP Simulation Hybrid Electrode Capacitor Self-Healing CircuitZ.H. Kong, L.G. Wu and Z.F. Luo 1893
Research on Smart Meter BOA and System DesignJ.Y. Zhao, J.M. Cheng and W.H. Ding 1897
The Simulation of APF Based on Three-Phase VSIY.F. Wang, G.Y. Liu, X.G. Lv and Z.C. Wang 1901
The Research and Application of Reactive Compensation Technology for Oilfield 10kVLinesX.M. Wu, Y. Feng and X.M. Xiang 1906
Design of GTAW Wire Feeder Control System Based on Nios IIF. Yang, S. Zhang and W.M. Zhang 1909
Ultralow-Repetition-Rate High-Energy Square Wave Pulse Amplification System for theBrillouin Optical Fiber Sensing SystemH. Tian, C.Q. Yin, A.Q. Lv and Y.Q. Li 1913
Application of Wireless Communication in Multi-Channel Temperature Control SystemL.M. Wen 1918
Investigating the Impact of Hybrid Energy Storage System on Isolated Power SystemX.Z. Wang, L. Xia and C. Zhang 1923
AC Excitation and Speed Governing Coordination Control of Impulse HydroelectricGenerating Unit and its SimulationX.Q. Hu, W. Liu and L. Zhang 1930
The Influence of Exciting Inrush Current of Transformer Differential ProtectionY.H. Wang 1935
Chapter 14: Communication Technology, WEB and NetworkEngineering
GSEP: an E-Mail Protocol Based on Generalized SigncryptionY.L. Si 1941
Low-Rate Application-Layer DDoS Attacks Detection by Principal Component Analysis(PCA) through User Browsing BehaviorX.Q. Di, H.M. Yang and H. Qi 1945
A Dynamic Trust Evaluation Model for Internet ComputingF. Li and Y.L. Si 1949
A Dynamic Cell Range Expansion for LTE-Advanced Heterogeneous NetworksM.F. Dai, Q.Y. Song and Z.L. Ning 1954
Dynamic Output Feedback H∞ Controller Design in Multiple-Packet Transmission withLimited CommunicationD.L. Wen and H.Y. Deng 1958
Stabilization for Networked Control Systems with Limited CommunicationY.Y. Liu and Y.K. Chu 1963
The Design of Dual Band Circularly Polarized Patch Antenna for Civilian GPS ApplicationsG.X. Jiang 1967
An Adaptive Web Information Extraction Approach Based on STU-DOM TreeS.P. Wu and Q. Wang 1972
Enhanced Power Allocation and Relay Selection Scheme in Two-Way Relaying CognitiveRadio NetworksD. Chen, X. Li, L.P. Su and J. Liang 1979
Performance Analysis of Uniform Fiber Bragg GratingL.L. Wang, X.Y. Qiu and Q.M. Ma 1984
A New Measurement Method of Conducted EMI on the Power-Line CommunicationsChannelW.L. Fu, Y.L. Guan and Y. Lu 1988
Applied Mechanics and Materials Vols. 397-400 q
Traffic Prediction Based on Grey Model Optimized by Buffer Operator and PSO inCommunication Network for Electric PowerR.Z. Wu, Y. He and L.R. Tang 1994
Cryptanalysis and Improvement of a Strong Designated-Verifier Proxy Signature SchemeL.G. Yang, F.N. Ou and J. Zhao 1999
Research on the Technology of Low-Voltage Power Line Carrier-Current CommunicationBased on OFDMW.Y. Ding, Z.N. Sun and X.L. Wang 2004
The Discussion on Communication Simulation MethodsH.W. Pei, J. Pan, Z. Pei and M. Xu 2008
Improved Binary Tree Search Anti-Collision AlgorithmC. Li and H.L. Xiong 2012
Research on Digital I/O Modules Based on Bluetooth CommunicationC.F. Kang and C. Zang 2019
FPGA Implementation of a Novel Multi-Rate QC-LDPC Encoder for DTMB StandardF. Wang, P. Zhang and C.Y. Liu 2024
All-Optical Wavelength Conversion Based on XPM in HNLFL.L. Wang, X.Y. Qiu and Q.M. Ma 2028
A Secret Sharing Algorithm Based on Regenerating CodesS.Z. Zhang and H.L. Song 2031
A Mental Clustering Algorithm Based on the Embedded Agent in Wireless Sensor NetworkY.M. Jian, M. Chen and G.F. Feng 2037
A Polling Control Protocol with Energy-Saving for Wireless Sensor NetworkM. He, L.Y. Bao and L. Deng 2042
RSSI Based Monte-Carlo Localization Boxed AlgorithmQ. Qu, Y. Xia, Y. Jiang and X.B. Chen 2048
The Design of MMS and SMS Student Service System Based on PCG.X. Li 2052
Design and Actualization of Intrinsically Safe Voice Warning System for MineL.L. Gao, Z.X. Luan and Y.F. Liu 2056
Research of Selective and Incremental Information Fusion Method Based on BayesianNetworkL.W. Zhang, J. Zhang and Y. Sun 2060
Investigation of the Impact of BIM&IPD on Change Orders Using Bayesian NetworkMethodM. Liu 2064
Study on the Deposition Methods of Institutional Repositories Based on Sword ProtocolX.S. Wang 2069
Chapter 14: Communication Technology, WEB and NetworkEngineering
Active Queue Management Based on State Variable Feedback ControlQ. Jing and M.M. Gu 2077
Synchronization of Two Different Complex Dynamical Networks with InterconnectionX.L. Zhou 2081
The Research and Application of Simulation Learning ToolA.H. Tian, C.B. Fu and L.M. Cui 2086
The Design and Research of Virtualization PlatformA.H. Tian and C.B. Fu 2090
Chapter 15: Signal and Intelligent Image, Video InformationProcessing, Data Mining
Study of Selective Video Encryption for the H.264 StandardQ.H. Wang and X.J. Wang 2097
r Advanced Design and Manufacturing Technology III
Gear Incipient Diagnosing Based on EEMD and Genetic-Support Vector MachineC.Y. Xiao, B.Q. Shi, Z.J. Hao and S.M. Zhu 2104
Partial Discharge Identification Using Multiple Features Fusion Based on Evidence Theoryand Support Vector MachineY. Xu 2111
An Application of the Frequency-Domain Experience Mode Decomposition to EnhanceDeconvolution ResultsY.N. Zhang, Y.S. Dai, J.J. Ding, M.M. Zhang and R.R. Wang 2120
A New Algorithm of Weld Seam Detection Based on Mathematical MorphologyB.J. Zou, N. Fang and R.X. Zeng 2124
Random Phase Weak Sine Signal Detection Based on Autocorrelation and Chaos TheoryF.Q. Cheng and Y.W. Shi 2129
Non-Invasive Image Processing Method for Detecting Seed VigorM.J. Li, J.H. Guo, Z. Yu, L. Yan and N. Han 2134
A Data Recorder with Optimized Recording Algorithm Used in UAVS.Y. Gao 2138
Improved Elastic Model Matching Algorithm for Facial Expression RecognitionW.D. Zhao, J. Zhang and Y.D. Zhang 2143
Tunnel Face Image Segmentation OptimizationC. Du and B. Leng 2148
A Research Review of Hilbert-Huang Transform Used for Rolling Bearing Fault DiagnosisQ. Li and H. Wang 2152
Method to Estimate and Promote SNR of Covariance Matrix in Array Signal ProcessingY.R. Shi, Y.T. Tian, H.W. Shi and L.X. Zhu 2156
Analysis of Pipeline Dynamic Flow Signal Coupling in Hydraulic SystemJ. Zhang, W. Wang, H.M. Tang, X.H. Li and C.B. Fu 2161
Compressed Sensing with Generalized Hebbian Algorithm in Video Frame PredictionM.M. Gu and Q. Jing 2167
Underwater Image Transition Region Extraction and Segmentation Based on SVMC.P. Chen, L. Zou and W. Wang 2171
Research on Data Processing Method for Continuously-Varying Dynamic Pressure FlutterTestH.T. Guo, B.B. Lv, L. Yu, Y. Yan and X.P. Kou 2177
The Frequency-Domain Analysis of the Rheological Data Acquired with Multi-Function andAll-Electric RheometerX.G. Li, D.X. Li, Y.J. Liu, P.Y. Feng, C.Y. Du and F. Zhao 2182
P300 Oddball Task and Classification Based on Support Vector Machine for BCI SystemG.C. Cui and J.T. Cao 2187
The Methodology Analysis of Traffic Volume Data Processing of Regional Road NetworkBased on Bi-Level Programming ModelsX.L. Meng and D.W. Chen 2191
Image Acquisition Method Based on TMS320DM642L. Liu and Q.H. Wu 2196
Design and Implementation of a New Type of Underwater Acoustic Target SimulatorT.X. Li, X.M. Zhang and Y. Chen 2200
A New Method of Fundus Image Enhancement Based on Rough Set and WaveletTransformW.D. Zhao, Y.D. Zhang and C.X. Jin 2205
Research on Sound Source Localization System Based on Time Delay EstimationC.Y. Zhang, C.W. Mi and P.Y. Yao 2209
Ultrasonic Testing Signal Denoising Based on Matching PursuitsX.L. Du and Y.H. Jiang 2215
Analysis about Coordinate of Cepstrum and its Application in Gearbox Fault DiagnosisY.J. Guo and J. Han 2219
An Overview of Moving Target Abnormity Behavior Identity Technology in VideoSequenceY.C. Song, B. Liu and M. Li 2223
Applied Mechanics and Materials Vols. 397-400 s
Freeway Traffic Congestion Identification Based on Fuzzy Logic InferenceM.L. Peng, X.R. Liang, C.J. Dong and Y.Y. Liu 2227
Real-Time Boundary Detection of Fast Moving Object in Dark SurroundsP. Miao, S.H. Feng, Q. Zhang and Y.Y. Ji 2231
Image Denoising in Frequency Domain Based on Analogical Basis DeconstructionF.Q. Liu, Z. Chao, Y.Y. Ji, Q. Zhang and P. Miao 2235
Speech Stream Detection for Noisy Environments Based on Empirical Mode DecompositionQ. Tang, D.X. Zhang and Q. Yan 2239
Web-Based Media Asset Management System DesignL.L. Deng 2243
Defective 2D Barcode Image Mosaic Method for Rotary Scanning Serial ImageJ.J. Wang, S.S. Zhang and W.P. He 2248
Image Pro-Correction for Defocus Blur Image Based on Wiener FilteringQ. Li, Y.H. Tai, Z.Q. Chen, Q.Y. Yang and B. Zhuo 2257
A Signal Detection Method for Harmonic Signal Submerged in Complex Noise BackgroundA.J. Quan, X.D. Sun and L.X. Zhu 2262
Research of the Disguise Identity Based on EEGX.M. Zhang, Z.G. Xiong and Z.D. Mu 2266
The MATLAB Realization of Toning up Digital Image Based on Wavelet TransformX. Cao, H.X. Zhang and Y.N. Xie 2270
The Research on Data Acquisition Subsystem for Aluminum Reduction Cells underReconstructionM. Liu and Q.W. Li 2274
Improvement Hardware Design of High Power and Ultra-Low Frequency Signal Source inCased Hole Resitivity LoggingC.F. Gao, X.M. Wu and J.T. Zhang 2278
Simulation Analysis Based on Finite-Difference Time-Domain Algorithm for GIS PartialDischarge DetectionQ.P. Liu and X.H. Wang 2282
A PAPR Reduction Method for Hexagonal Constellation-Based OFDM SignalsJ.Q. Zheng and Y.J. Wang 2287
Based on k-Medoids and c5.0 Joint Constraint of the Drug Information Mining AlgorithmH. Zhang 2291
Research on Asset Recognition Algorithm of Information Security Product Based onDecision Tree AlgorithmF. Shuai and J.Q. Li 2296
A Dynamic Sliding Window Based on Otsu Method for Binary License Plate and CharacterRecognitionR. Jian and J. Zhao 2301
Extraction Research about Parallelization of Named Entity Based on Hadoop PlatformQ. Shi, Z.D. Yang and L. Xu 2309
Trademark Recognition Based on Hu Modified Invariant MomentsM. Huang, Y.Q. Ma, H.Z. Shu and Q.P. Gong 2313
Fast Tone Mapping Based on SortingF.Q. Liu, Y.G. Zhang, Z. Chao and P. Miao 2318
Research on Online Visual Inspection System for Multi-Feature Trademark DefectB. Yang, B.G. He and Y. Chen 2322
The Analysis and Data Mining of Students’ Online Data Based on Digital CampusQ. Shi, Y. Qian, Y. Gong, X.M. Zhu and J.Q. Yan 2326
Cyclic Relation Method for DOA and Polarization Parameters Estimation of ArbitraryPolarized ArrayY.R. Shi, Y.T. Tian, L.X. Zhu and L.F. Deng 2330
Research on Maize Varieties Recognition System Based on Image ProcessingL.M. Deng, T. Luan and W.J. Ma 2335
Medical Bottle Tightness Detection Based on Digital Image ProcessingB.J. Wang and G.Y. Yang 2340
t Advanced Design and Manufacturing Technology III
Chapter 16: Software Development and Application
The Data Manipulation Platform of Well-Logging Information Based on AgentL.P. Yang and W. Wang 2347
Research and Realization of the Software Requirements Management Integration PlatformP. Tian, Y.F. Zhang, W. Li and T.J. Li 2351
Research on the Embedded Software Reliability Evaluation Model Based on InfluenceFactorsP. Tian, L.N. Gong, W. Li and W.T. Tian 2355
An Access Control Model for XML RepositoriesH. Zhong 2360
Application of Weight Adjustment Technique in the Deep Web Data Source ClassificationX.Q. Zhou, J.X. Sun and S.B. Wang 2367
Research for College Counselors' Work Auxiliary System Based onB/S ArchitectureH.J. Wang and K. Tao 2371
Applying MPC08SP Motion Control Card to the Development of Open CNC System ofGrooving MachinesC. Song and M.F. Yin 2375
Research and Application of Music Digitalization Based on MATLABM. Chen, C.L. Wang, Q.T. Zeng and H.Z. Zhang 2379
Integration of Systematic RBAC Security Model and UML ModelB.D. Fan 2383
Research on the Digital Earth Based on OpenGLH.W. Wang, J.C. Quan, D.J. Li and J. Xie 2387
Research on Feature Based IC Process Modeling and ClusteringJ.F. Feng, J. Ma, J. Hu and Y.H. Peng 2391
Optimal Route Retrieval Model Based on Assignment StrategyF. Zong and H.L. Xiong 2398
U Nong Shu Cai Tong System - The Agricultural Expert System Based on U DiskG.D. Li, J.F. Zhang, H.G. Zheng and C.P. Tan 2406
Chapter 17: Computer Applications and Information Technologies inIndustry and Engineering
The Construction of Psychology Lessons Planning Platform Based on the SSHY. Wang 2415
A Simple Three-Dimensional Terrain Modeling Method for Complex Terrain WindEnvironment SimulationS.L. Chen, J. Lu, W.W. Yu and S.L. Zhang 2420
Analysis of the Data Mining Application Based on Cloud ComputingX.H. Li, W. Liu and L.L. Wang 2426
The Design of Universities Resource-Sharing Network Teaching System Based on CloudComputingQ.Y. Guo 2430
Early-Warning Model for TECC Based on Gray Neural Network - Taking LaolongtouScenic Area as an ExampleX.P. Yang and E.C. Li 2435
The Research on Vehicle Routing Problem Based on Improved Ant Colony AlgorithmZ.Q. Jiang and Y. Wu 2439
Digital Earth and Exploration of Military ApplicationH.W. Wang, M.Q. Yang, X.R. Sun and J. Xie 2447
Finding the Good in Health Care System Based on Iteration ModelT.F. Zhang, M.J. Song and H.Y. Zhang 2451
Applied Mechanics and Materials Vols. 397-400 u
Research on Spatial Cognition Training Based on the Digital EarthH.W. Wang, J. Xie, X.J. Wang and H.N. Wu 2455
Effectiveness Calculation of Multiple Rounds Simultaneous Impact Shooting Method Basedon Monte Carlo MethodX.J. Hu and H.Y. Wang 2459
Detection for Approximately Duplicate Records Based on Fuzzy Comprehensive EvaluationL.J. Zhou and Z. Xiao 2464
Research on Cooperation Mechanism of Multi-Agent Grinding Control System Based onBlackboard ModelH.W. Zhao, Y.M. Qi, D. Zhao and S.H. Pei 2469
Research of the Integration Model of Coal Heterogeneous SystemsH.P. Zhou and K.L. Sun 2473
Minimum Normal Cone for Continuous Collision DetectionY. Shui, J.J. Zheng and H.J. Zhou 2477
A Design of Ubiquitous Learning Environment with the Support of Pervasive ComputingJ. Zhang, L.W. Zhang and B. Liu 2483
Transformation Formulas between Bezier Curve and Partial said-Ball CurveW. Xue, P. Xi and Y.D. Wang 2487
Research on General Data Publish/Subscribe Model Based on DDSX.J. Ma and S.F. Liu 2491
A Research on Sports Training Auxiliary System Based on Cloud ComputingH.J. Wu, X.K. Li and H.Y. Zhao 2495
The Service Platform for Barrier-Free Special Education Based on Cloud ComputingL.P. Yang, W. Wang and C.L. Li 2499
Construction of Drought Indices from Passive Microwave Remote Sensing AMSR-E Data inHuaihe River BasinR. Wang, J.W. Xu, D. Wang, X.M. Xie and P. Wang 2503
Quantitative Assessment of Expert's Lifting-Thrusting Manipulation in Acupuncture Basedon Haptic DeviceP. Miao, Q. Zhang, Y.Y. Ji, J. Jiang, H.D. Guo, F.B. Wang and Z.G. Yan 2507
Emergency Scheduling Model of Urban Rail Transit Based on Genetic AlgorithmY.J. Li and Y. Fang 2511
The Application of Decision Tree in Security AuditD. Shao and Y.B. Wang 2517
Some New Generalized Nonlinear Difference Inequalities and their ApplicationW.S. Wang, Y.H. Lin and X.L. Gao 2521
Minimum Spanning Tree Dynamic Demonstration System ImplementationB.Z. Chen and X.B. Yang 2526
Calculation of Slope Safety Coefficient Based on Newton’s IterationQ. Zhang, Y.J. Zhang and Z.W. Yu 2531
Analysis and Improvement of BLP Model for Multi-Level Security DatabaseH.Y. Zhao, X.Y. Liu and J. Zhao 2536
A Constellation Graph Based Approach for Ontology ConstructionY.L. Liu and Y. Yang 2540
Chapter 18: Production and Operation Management, Supply Chain,Electronic E-Commerce and Internet of Things Application
Integrating Modular Units into the Production Line and MRO in Career Apparel IndustryJ.H. Yang, Y. Song and Z.C. Ma 2549
The Limit Price Strategy Analysis of Integrated Medicine Supply Chain Based onGovernment RegulationL. Shen and Y.Y. Wang 2553
Research on Network Learning Mechanism of Enterprise Network Resource CoordinationY.G. Shi, Y.T. Song, S.M. Ma and J.F. Yan 2557
Developing the Coal and Power Pool Project, Structuring Large-Scale Coal EnterprisesM. Song and C. Zhang 2561
v Advanced Design and Manufacturing Technology III
The Establishment of Production Capacity Evaluation Indicator System Based on R-Clusterand Coefficient of VariationL.Y. Tao, Z.D. Li and M. Zhang 2565
An Ant Colony Algorithm for Integrating Assembly Sequence Planning and Assembly LineBalancingZ. Yang, C. Lu and H.W. Zhao 2570
The Economics and Feasibility of Traceability in Agri-Food Supply Chain: Analysis withGame Theory between Double OligarchsJ.C. Wu, C.X. Wu and Y.P. Liu 2574
Study the on Time Delivery Based on Product Lifecycle Management in Supply ChainH. Chen 2581
The Study of Buffer Allocation with Travel Time in Stochastic Production Flow LineX.Y. Pan, J. Wu, Q.W. Zhang, D. Lai, X. Fu and C. Zhang 2589
The Effects of Demand Randomness in Newsvendor ModelZ.B. Lin 2595
Study on Multi-Objective Optimizing Model of Cigarette Production LineJ. Yin, W.L. Wang and H.Z. Zhu 2601
A Study on Malaysian Food and Beverage Manufacturing SMEs Practices of Pre-Development ProcessN.H. Abu, B.M. Deros, M.N.A. Rahman and M.F. Mansor 2605
Design and Application of Project Management System for Project-Driven EquipmentManufacturing EnterpriseY.X. Chen, S.S. Guo, B.G. Du and L.B. Sun 2610
Study on the Intra-Ship Material Handling SystemF. Li and D.F. Han 2618
Logistics Simulation and Optimization Design of One Production Line Based on FlexsimX.Y. Tang, J. Shi, L.C. Chen, L.L. Yang and X.M. Leng 2622
Key Factor Extraction of Supply Chain Performance Based on Heterogeneous SelectiveEnsemble PCAC.H. Zhang, N. Zhao and H.Y. Shao 2626
The Optimization Research on the Green Supply Chain NetworkY.J. Fang and M.N. Wu 2631
Study and Application of Supplier Performance Evaluation System Based on the Triple-ASupply ChainH. Dong and S. Dong 2636
A Cross-Layer Congestion Control Algorithm Based on Traffic Prediction in WirelessSensor NetworksY. Sun, M. Li and P. Xu 2641
Research on the Feasibility of Express Freight Transport on High-Speed Railway in ChinaY.K. Zhang and S.P. Qin 2647
Research on Separating Mode of Business and LogisticsY.G. Shi, H.X. Li, W.J. Song and J.F. Yan 2651
Research on Mining of E-Procurement Model Parameters Based on Decision TreeP. Wu, Y.F. Huang, Q.Q. Cao and F. Xiong 2655
Agile Supply Chain Performance Evaluation of Automobile Manufacturing Based onRegression AnalysisH. Dong and C.L. Li 2662
The Entropy Weight Fuzzy Comprehensive Evaluation of Green Logistics CostManagementH. Dong and S.N. Wang 2667
Model Innovation of Exhibition Logistic Supply ChainX.M. Wang 2672
Study on the Development Strategy of Lean Logistics for Automobile Enterprises underGreen Supply Chain EnvironmentD. Liang and H. Wang 2677
Customer Satisfaction Evaluation of Ceramic E-Commerce PlatformF.B. He, Y.L. Zhang, T.J. Guo and H. Chen 2681
Commodity Coding Research and Application of Ceramic E-Commerce PlatformF.B. He, Y.L. Zhang, T.J. Guo and H. Chen 2685
Applied Mechanics and Materials Vols. 397-400 w
Study on Railway Materials Procurement OnlineL. Sun, H.M. Xing and Y. Zhang 2689
Study on Railway Passenger Service Based on Customer PerceptionC. Zheng, B.M. Hu and L. Bei 2693
Chapter 19: Management and Education Engineering
Study on Virtual Reality Techniques Used in German TeachingY. Jia 2701
Research and Practice on Data Analysis Evaluation Technique of Intelligent Teaching-Management Based on D-M TheoryS.F. Jiang and Y.Y. Cui 2705
Research on Group Decision Making Model of Low-Speed Pure Electric Vehicle'sTechnology Integrated InnovationC.Q. Liu and G.P. Cheng 2709
Creation and Practice of Teaching System on Engineering Training for TrainingDistinguished EngineersX.W. Miao, G.F. Yuan and Y.Q. Gu 2713
Social Impact Assessment of AMT Project Based on the Information Entroy TheoryG.H. Wang 2718
“Forgettingness” Parameter as a Criterion for Assessing the Quality of Teaching Physics toFuture EngineersT.N. Gnitetskaya and E.B. Ivanova 2722
Research on E-Commerce Teaching SystemX. Ren, B. Liu and H.J. Jiang 2726
Analysis of Development of Real Estate Industry Based on FA and CAX.C. Shi and D.Y. Jiang 2731
Open Experimental Teaching in Fluid MechanicsB. Zheng, Y.Q. Liu, R.X. Liu, J. Meng and M.M. Mao 2735
Teaching Reform and Thinking of the Course Electro-Mechanical Systems Dynamics Basedon Higher Engineering Education ModeQ.Y. Wang and J. Chen 2739