Post on 18-Jan-2016
transcript
TARGIS The New CEROMER Material
Ceramic optimized polymer
What is the Targis?
• Light activated veneering material made of Ceromers
• Ceramics ( esthetics ) + Resins (Flexual strength)
• Unmatched Ceromer material– 75-85 weight % of Inorganic filler– Ceramic particle– Organic matrix
Indications (Targis)
• Metal-free bridges with Vectris fmwk
• Metal-free single posterior crowns with Vectris fmwk
• Metal-reinforced crown, bridge, and implant veneers
• Metal-free anterior crowns
• Metal-free inlays,onlays, veneers
• Metal-reinforced combination dentures
Contraindications
• Metal-free bridges with more than one pontic between two abutment teeth
• Allergic patient
Side effects
• Hypersensitivity on skin - uncured Targis material
• Avoid eye contact
General Steps
• Shade selection
• Preparation of Model– Sealing of die: Die hardener/Separating varnish– Drying is important– Check tolerance with separator
• Modelling of wax– Isolation
• Two coat - 3 min dry on each coat
• Check the sharp edge area - thin coat
Metal-reinforced crown, bridge, and implant veneers
• Alloys - Corrosion resistant alloys– Copper and/or silver content: < 50%– Gold, platinum content: < 90%
• High gold alloys containing more than 90% gold, platinum must only be used in combination with retentive elements
• Life Like Esthetics– Translucency– Fluorescence
• High Flexual strength
• Enamel-like Abrasion
VECTRISThe New FRC Material
Fibre-reinforced composite
• Advanced Framework Material– Fibre-reinforced Vectris material
– Metal-free, translucent frameworks
• Proven fibre-reinforced technology– Composed of several layers of fibre wafers
– Uniaxially oriented fibre bundles– Excellent elasticity and distribution of strain
• Outstanding translucency– Metal-free, translucent Vectris
• High Flexual strength
1. Modelling– Wax up a simple beam-like pontic on the model– Fabricate a silicone key and remove the wax
2. Framework fabrication– Place a Vectris Pontic in the occlusal opening of the
silicone key, according to the situation– A process combining vacuum, pressure, and light in
the state-of-art Vectris VS 1 produces highly accurate, bubble-free frameworks
3. Finishing– Finish Vectris Pontic and replace it on the
model– Reinforce with a Vectris Frame– Optimum adaptation and curing is achieved
with the fully automatic Vetrix VS 1 franework former
4. Bridge Framework– The finished framework made of Vectris Pontic
and Bectris Frame is ready for the esthetic Targis veneer
Molar framework– Vectris Singles are used to fabricate esthetic
single paoterior frameworks easily and accurately
Prefabricated Vectris components
• Vectris single
• Vectris pontic
• Vectris Frame
• Vectris Glue
• Applicator
• Vectris VS 1– Vaccum, Pressure, Light Furnace
Targis on Vectris / Targis on Metal
• Fabrication of metal-free framework with Vectris– Bond with translucent Targis Base
• Framework fabrication without mechanical retention– Targis Link to reinforce the bond between the
metal and the framework mat4rial– Targis Opaquer
• Additive crown buildup and individualized shading– Targis quick– Targis stains– Targis impulse– Targis gingivae– Targis power
• Adhesive cementation
• Conventional cementation
• Targis Power– High-performance curing unit– Light and Heat
• Targis Quick– Initial curing light for quick precuring