Post on 02-Jun-2020
transcript
Warmth and elegance of fabric are enriched by the appeal of used and reused materials that are
perfectly worn. Thanks to a complete and modern color palette and a full range of trim pieces and
decors, this fabric gives life to environments that convey a total feeling of comfort.
FRAYFray White 123/8”x221/2” - 31.5x57 cmFray Gray Mosaic 113/4”x113/4” - 30x30 cmFray Gray 235/8”x235/8” - 60x60 cm
FLOOR WALL
Pearl Pearl
Gray
Smoke
Sand
White
Sand
White
FRAYCOLORED BODY PORCELAIN STONEWARE
2
COLORS
FRAYFray Gray Mosaic 113/4”x113/4” - 30x30 cm
Fray Gray 235/8”x235/8” - 60x60 cm
3
White
Pearl
Sand
FRAYCOLORED BODY PORCELAIN STONEWARE
4
Gray
Smoke
5
SHADE VARIATION - FLOOR
FRAYCOLORED BODY PORCELAIN STONEWARE
6
FRAYFray Pearl Bullnose 3”x24” - 7.2x60 cmFray Pearl 113/4”x235/8” - 30x60 cm
7
FLOOR
FRAYFray Smoke 235/8”x235/8” - 60x60 cm
Compliant with standards ANSI A137.1-2012
V1
UNIFORM APPEARANCE
FRAY Pearl235/8”x235/8” - 60x60 cm - Rectified
FRAY Sand235/8”x235/8” - 60x60 cm - Rectified
FRAY Smoke235/8”x235/8” - 60x60 cm- Rectified
FRAY White235/8”x235/8” - 60x60 cm - Rectified
FRAY Gray235/8”x235/8” - 60x60 cm- Rectified
FRAY Pearl113/4”x235/8” - 30x60 cm
FRAY Sand113/4”x235/8” - 30x60 cm
FRAY Smoke113/4”x235/8” - 30x60 cm
FRAY White113/4”x235/8” - 30x60 cm
FRAY Gray113/4”x235/8” - 30x60 cm
FRAY
8
SIZE - THICKNESS 113/4”x 235/8” - 30x60 cm / 235/8”x 235/8” - 60x60 cm 9 mm FINISH MATTE
FRAY White
Bullnose 3”x 24” - 7.2x60 cm
Cove base6”x12” - 15x30 cm
FRAY Sand
FRAY Pearl
FRAY Gray
FRAY Smoke
FRAY White Mosaic113/4”x113/4” - 30x30 cm (Mosaic 2”x2”)
FRAY Tatami Warm *113/4”x113/4” - 30x30 cm(Tatami Mosaic 1”x6”)
FRAY Sand Mosaic113/4”x113/4” - 30x30 cm (Mosaic 2”x2”)
FRAY Tatami Cold *113/4”x113/4” - 30x30 cm(Tatami Mosaic 1”x6”)
* Mixed mosaic, available in Warm (White, Sand, Pearl) and Cold (Pearl, Gray, Smoke)
FRAY Pearl Mosaic113/4”x113/4” - 30x30 cm (Mosaic 2”x2”)
FRAY Gray Mosaic113/4”x113/4” - 30x30 cm (Mosaic 2”x2”)
FRAY Smoke Mosaic113/4”x113/4” - 30x30 cm (Mosaic 2”x2”)
9
FLOOR
V1
UNIFORM APPEARANCE Compliant with standards ANSI A137.1-2012
MOSAICS
COORDINATING TRIMS
Pearl
White
Sand
FRAY
10
WHITE BODY WALL TILES
FRAYFray White 123/8”x221/2” - 31.5x57 cmFray Tatami Warm 113/4”x113/4” - 30x30 cm Fray Stripe Warm 123/8”x221/2” - 31.5x57 cm
11
SHADE VARIATION - WALL
FRAY
12
WHITE BODY WALL TILES
FRAYFray Pearl Mosaic 12”x12” - 30.5x30.5 cmFray Pearl Wall Bullnose 2”x123/8” - 5x31.5 cmFray White 113/4”x235/8” - 30x60 cm
13
Compliant with standards ANSI A137.1-2012
FRAYFray White 123/8”x221/2” - 31.5x57 cm
Fray Tatami Warm 113/4”x113/4” - 30x30 cm Fray Stripe Warm 123/8”x221/2” - 31.5x57 cm
Fray Sand 113/4”x235/8” - 30x60 cm
V1
UNIFORM APPEARANCE
WALL
FRAY
14
SIZE - THICKNESS 12 3/8”x 221/2” - 31.5x57 cm 8.5 mm FINISH MATTE
FRAYFray Pearl Mosaic 12”x12” - 30.5x30.5 cmFray Pearl Wall Bullnose 2”x123/8” - 5x31.5 cm
FRAY White
Wall Bullnose2”x 123/8” - 5x31.5 cm
Corner Line 1/2”x 123/8” - 1.5x31.5 cm
FRAY Sand
FRAY Pearl
COORDINATING TRIMS
FRAY White12 3/8”x 221/2” - 31.5x57 cm
FRAY Pearl12 3/8”x 221/2” - 31.5x57 cm
FRAY Sand12 3/8”x 221/2” - 31.5x57 cm
FRAY Stripe Warm12 3/8”x 221/2” - 31.5x57 cm
FRAY Stripe Cold12 3/8”x 221/2” - 31.5x57 cm
MOSAICS
FRAY White Mosaic12”x12” - 30.5x30.5(Mosaic 1”x3”) cm
FRAY Sand Mosaic12”x12” - 30.5x30.5(Mosaic 1”x3”) cm
FRAY Pearl Mosaic12”x12” - 30.5x30.5(Mosaic 1”x3”) cm
15
Compliant with standards ANSI A137.1-2012
V1
UNIFORM APPEARANCE
WALL
Every Atlas Concorde USA porcelain stoneware collection is PTCA Certified. Under the program, established jointly by the Porcelain Tile Certification Agency (PTCA) and the Ceramic Tile Distributors Association (CTDA), manufacturers can “prove” their product is really porcelain (meeting the water absorption criteria of the American national standard - ASTM C373).
LEED (Leadership in Energy and Environmental Design) is a rating system created to encourage the construction of “green” buildings. Developed by the US Green Building Council and internationally recognized, it points out the necessary requirements to build eco-compatible projects, capable of functioning in sustainable and autonomous way in terms of energy consumption as well as having a low environmental impact throughout their entire life-cycle. Atlas Concorde USA is a member of the US Green Building Council.
Atlas Concorde USA products are low-emitting materials with zero emission of volatile organic compounds (VOC). This can contribute to the awarding of 1 LEED credit.
Atlas Concorde USA is a member of TCNA, a trade association representing manufacturers of ceramic tile, tile installation materials, tile equipment, raw materials, and other tile-related products. The Tile Council is recognized for its leadership role in facilitating the development of North American and international industry quality standards to benefit tile consumers.
The Ceramic Tile Distributors Association (CTDA) is an international association of distributors, manufacturers and allied professionals of ceramic tile and related products. CTDA connects, educates and strengthens tile and stone distributors. Atlas Concorde USA is a member of CTDA.
ATLAS CONCORDE USA, INC. - 117 Seaboard Lane - Suite 170 - Franklin, TN 37067 - USA
PERFORMANCE & FEATURES
(*) Whichever is less(1) May not apply to textured surfaces or tiles with uneven back patterns.
WHITE BODY WALL TILES
Compliant with standards ANSI A137.1-2012 SIZE - THICKNESS 123/8”x 221/2” - 31.5x57 cm 8.5 mm
FIELD TILES - Available in all colors
Nominal size (in) Thickness (mm) Finish
12 3/8” x 22 1/2” 8.5 mm Matte
MOSAICS AND COORDINATING TRIMS - Available in all colors
Nominal size (in) Thickness (mm) Finish
Mosaic 1”x3” 12” x 12” 8.5 mm Matte
Wall Bullnose 2”x12” 2" x 12 3/8" 8.5 mm Matte
Corner Line 1/2”x12” 1/2" x 12 3/8" - Matte
V1UNIFORM APPEARANCE
Differences among pieces from the same production run are minimal.
FINISH MATTE
www.atlasconcordeusa.com
Glazed Wall Tile Specifi cation
PROPERTY ASTM TEST METHOD
Calibrated Rectifi edFRAY Wall
Minimum Maximum Minimum Maximum
REGULARITYCHARACTERISTICS
Nominal Size
ASTM C499
-2.00% 2.00% -2.00% 2.00% Compliant
Caliber Range (Variation from average facial dimension of sample)
-0.30% or -0.04 in (-1.0 mm) (*)
0.30% or 0.04 in (1.0 mm) (*)
-0.25% or -0.03 in (-0.8 mm) (*)
0.25% or 0.03in (0.8 mm) (*)
Compliant
Thickness (1) N/ARange: 0.031 in (0.79 mm)
N/ARange: 0.031 in (0.79 mm)
Compliant
Wedging ASTM C502 -0.40% or -0.05 in (-1.3 mm) (*)
0.40% or 0.05 in (-1.3 mm) (*)
-0.25% or -0.03 in (-0.8 mm) (*)
0.25% or 0.03 in (0.8 mm) (*)
Compliant
Warpage EdgeASTM C485
-0.30% or -0.04 in (-1.0 mm) (*)
0.40% or 0.05 in (1.3 mm) (*)
-0.30% or -0.04 in (-1.0 mm) (*)
0.40% or 0.05 in (1.3 mm) (*)
Compliant
Warpage Diagonal -0.30% or -0.05 in (-1.3 mm) (*)
0.40% or 0.07 in (1.8 mm) (*)
-0.30% or -0.05 in (-1.3 mm) (*)
0.40% or 0.07 in (1.8 mm) (*)
Compliant
All Glazed Wall Tile
STRUCTURAL CHARACTERISTICS
Water Absorption ASTM C373 ≥ 10.0% 10% - 20%
BULK MECHANICAL CHARACTERISTICS
Breaking Strenght ASTM C648Average ≥ 125 lbf. (1.11 kN)
Individual ≥ 100 lbf. (0.44 kN)≥ 175 lbf. avg
PHISICAL PROPERTIES
Bond Strength ASTM C482 ≥ 50 psi (0.34 Mpa) ≥ 100 psi
THERMAL AND IGROMETRIC
CHARACTERISTICS
Crazing Resistance ASTM C424 Pass Resistant
Thermal Shock Resistance ASTM C484 Pass Resistant
CHEMICAL CHARACTERISTICS
Chemical Resistance ASTM C650 As Reported Unaffected
Stain Resistance ASTM C1378 As Reported Unaffected
www.atlasconcordeusa.com
Atlas Concorde Usa, Inc.117 Seaboard Lane - Suite 170
Franklin, TN 37067 - USA
Atlas Concorde reserves the right to modify any product without notice and will not be liable for any direct or indirect damage resulting from such modifications. Colors and optical features of the materials illustrated in this catalogue are to be regarded as mere indications. For information and details relating to codes, packaging and weight it is recommended to refer to the latest pricelist.
© Copyright Atlas Concorde USA, Inc. 2016The reproduction of the work, fully or in part, is strictly forbidden.
FIELD TILES - Available in all colors
Nominal size (in) Thickness (mm) Finish Rectifi ed edge
11 3/4" x 23 5/8" 9 mm Matte -
23 5/8" x 23 5/8" 9 mm Matte Yes
MOSAICS AND COORDINATING TRIMS - Available in all colors
Nominal size (in) Thickness (mm) Finish
Mosaic 2"x2" 11 3/4" x 11 3/4" 9 mm Matte
Tatami Mix Mosaic 1”x6” 11 3/4” x 11 3/4” 9 mm Matte
Bullnose 3"x24" 2 7/8" x 23 5/8" 9 mm Matte
Cove Base 6"x12" 5 7/8" x 11 3/4" 8.5 mm (*) Matte
Please refer to caliber chart for work sizes.Close joints are not recommended.(*): Cove Base thickness is 7 mm on � at top part.
ATLAS CONCORDE USA, INC. - 117 Seaboard Lane - Suite 170 - Franklin, TN 37067 - USA
PERFORMANCE & FEATURES
Porcelain Tile Specifi cation
PROPERTY ASTM TEST METHOD
Calibrated Rectifi edFRAY Floor
Minimum Maximum Minimum Maximum
REGULARITYCHARACTERISTICS
Nominal Size
ASTM C499
-3.00% 3.00% -3.00% 2.00% Compliant
Caliber Range (Variation from average facial dimension of sample)
-0.50% or -0.08 in(-2.0 mm) (*)
0.50% or 0.08 in(2.0 mm) (*)
-0.25% or -0.03 in (-0.8 mm) (*)
0.25% or 0.03 in (0.8 mm) (*)
Compliant
Thickness (1) N/A Range: 0.40 in (1.02 mm) N/A Range: 0.40 in (1.02 mm) Compliant
Wedging ASTM C502 -0.50% or -0.08 in (-2.0 mm) (*)
0.50% or 0.08 in(2.0 mm) (*)
-0.25% or -0.03 in (-0.8 mm) (*)
0.25% or 0.03 in(0.8 mm) (*)
Compliant
Warpage EdgeASTM C485
-0.75% or -0.09 in(-2.3 mm) (*)
0.75% or 0.09 in(2.3 mm) (*)
-0.40% or -0.05 in(-1.3 mm)(2) or -1.8 mm(3) (*)
0.40% or 0.05 in(1.3 mm)(2) or 1.8 mm(3) (*)
Compliant
Warpage Diagonal -0.50% or -0.08 in(-2.0 mm) (*)
0.50% or 0.08 in(2.0 mm) (*)
-0.40% or -0.07 in(-1.8 mm) (*)
0.40% or 0.07 in(1.8 mm) (*)
Compliant
All Porcelain Tiles
STRUCTURAL CHARACTERISTICS
Water Absorption ASTM C373 ≤ 0.5% ≤ 0.5%
BULK MECHANICAL CHARACTERISTICS
Breaking strenght ASTM C648Average ≥ 250 lbf. (1.11 kN)
Individual ≥ 225 lbf. (1.00 kN)≥ 350 lbf. avg
PHISICAL PROPERTIES
Bond Strength ASTM C482 ≥ 50 psi (0.34 Mpa) ≥ 100 psi
THERMAL AND IGROMETRIC
CHARACTERISTICS
Resistance to Freeze/Thaw Cycling ASTM C1026 As Reported Resistant
CHEMICAL CHARACTERISTICS
Chemical Resistance ASTM C650 As Reported Unaffected
Stain Resistance ASTM C1378 As Reported Unaffected
SAFETY CHARACTERISTICS
Dynamic coeffi cient of friction DCOF Requires a minimum value of 0.42 for commercial areas that are likely to be wet > 0,42 Wet
(*) Whichever is less(1) May not apply to textured surfaces or tiles with uneven back patterns.(2) Whichever is less, for tiles up to 24’’x24’’ (610 mm x 610 mm).(3) Applies to tiles larger than 24’’x24’’ (610 mm x 610 mm).
COLORED BODY PORCELAIN STONEWARE
Compliant with standards ANSI A137.1-2012 FINISHSIZE - THICKNESS 113/4”x 235/8” - 30x60 cm 9 mm235/8” x 235/8” - 60x60 cm 9 mm
MATTE
V1UNIFORM APPEARANCE
Differences among pieces from the same production run are minimal.
www.atlasconcordeusa.com