The GNU in RADIO

transcript

The GNU in RADIO

Shravan Rayanchu

• Getting the code close to the antenna– Software defines the waveform – Replace analog signal processing with Digital

signal processing

• Why?– Flexibility, time to market, reliable– Its all about the stack : GPRS/ WiFi / WiMax

• Possibilities …?– TX/RX on multiple channels simultaneously– Better spectrum usage– “Cognitive radios”

• Disadvantages– Higher power consumption (GPU vs ASIC)– More MIPS!– Higher cost (as of today)

GNU RADIO

• Platform for – Experimenting with digital communications– Signal processing using commodity hardware

• Free software!

• http://www.gnu.org/software/gnuradio/

A TYPICAL SDR

• Sampling Rate– Rate at which you sample the analog signal– Determines what frequency can be handled

• Dynamic range – Number of signal levels– Quantization error

• SNR = 6.02N + 1.76dB

Sum of sinusoids: Sigma ai Sin (2 pi fit)

Sampling

Sin (2 pi fc nts) = Sin (2 pi fc nts+ 2 pi m) = Sin (2 pi nts (fc + m/n fs))

fc + k fs

Sampling

We need a LOW PASS FILTER !

Sampling

Nyquist Criteria

Sampling freq > Twice the max. frequency component in the signal of interest

ALIASING

ADCs in USRP:64 Msps 32 Mhz

How to receive 2.4 Ghz ?RF Front end

RF Front End: Down conversion

LPF ADC

Mixer: sinusoid of (RF-IF)

Intermediate Frequency (IF)

RF Front Ends

• 50 - 860 Mhz RX

• 400 – 500 Mhz Transceiver

• 2300 – 2900 Mhz Transceiver – Bandpass filter (2.4 to 2.483 Ghz)

• Universal Software Radio Peripheral– To rapidly design powerful, flexible software

radio platforms

• What does it have?– FPGA (ALTERA Cyclone)– Mixed signal processor (AD 9862)– Slots for 4 daughter boards (2 TX, 2 RX)

Boot sequence: two programmable components

• USB Controller (Cypress FX2): 8051 code

• FPGA (ALTERA Cyclone): Verilog

• Four 12-bit ADC, 64 Msps – Sub-multiples are also possible: 42.66 Msps, 32 Msps, 25.6

Msps and 21.33 Msps– Decimation helps– IF has to be < 32 MHz

• Four 14-bit DAC 128 Msps – Max. output 50 Mhz

• Four I/Os simultaneously if we use real sampling, Two I/Os for complex sampling; synchronized clocks

• Each daughter board has access to 2 DACs and 2 ADCs• Why Different boards ?

– different RFs same IF

• Four Digital Downconverters (DDCs)– FPGA with CIC Filters– Programmable decimation rate– Low pass filter

• Two Digital Upconverters (DUCs)– AD 9862– Programmable interpolation rate

• USB 2.0 (480 Mbps, peak)

RX PATH

DDC : IF Complex Baseband

AD 9862

Block D: The "Fine Modulator" -- this is a digital up-converter

Block C: Interpolation filter (we interpolate by 4 in the AD9862)

Block B: The "Coarse Modulator"

Block A: The actual DACs.

TX PATH

GNU Radio Software Architecture

• Library of signal processing blocks (C++)– Ex: sources, sinks, others

• Input, output ports, types, ‘work function’

• Create a ‘flow graph’ : vertices are blocks and edges represent the data flow (Python)

• SWIG, FFTW, Boost …

Lets look into some code!

GENERATE DIAL TONE

Frequency Modulation

Spectrum Sensing

6 Mhz Limit

• USB 2.0 limit 32 MBytes/sec

• ADC 64 Msps 32 Mhz chunk

• 8 Msps w/ 16 bit I/Q samples– 8 * 2 * 2 = 32 Mbytes/sec– 4 Mhz * 2 = 8 Mhz (Quadrature sampling)– Discard 1/4 of bins ~ 6 Mhz

• Decimation (8, 256)

• Interpolation (16,256)

Spectrum Mask

Spectrum Sensing

Tune : 0.001 sec , Dwell : 0.1 sec , Step: 0.5 Mhz , FFT : 1 Mhz wide

Spectrum Sensing

Tune : 0.001 sec , Dwell : 0.1 sec , Step: 1 Mhz , FFT : 1 Mhz wide

Spectrum Sensing

Complex samples from USRP

Spectrum

Filter to get the actual channel we want

Demodulate to get ones and zeroes

Demodulate to get

Get the SYNC Vector

ones and zeroes

Demodulate to get

Get the SYNC Vector

ones and zeroes

Demodulate to get

Get the SYNC Vector

ones and zeroes

We have the pkt now

Demodulate to get

Get the SYNC Vector

ones and zeroes

We have the pkt now

Carrier Sense

RX CALLBACK

Some numbers ..

• Time to switch freq ~ 0.001 sec (Have to verify)

• Modulation:– GMSK, [ DBPSK, DQPSK didn’t work ]– Bit rate = 500k [ CPU Maxed out ]

• Throughputs:– UDP: 520 kbps ! (PHY: 500 kbps) : Error in

Netperf ?– TCP: 20 ~ 80 Kbps

Channel 1, less tries

2.412 (Channel 1) , 3.8% pkts in error

Channel 1, Ping flood, More tries

Channel 1, Ping source, More tries

4% error (throughput very less)

Channel 6

2.3% pkts in error

2.423 Ghz

~ 1.6% pkts in error

2.562 Ghz

0% pkts in error

Channel 1, Ping sourceCS_Thresh = 70 , 50

Error was ~ 4 % !!

What do we have?

• Multiple modulations: – BPSK, QPSK, GMSK, QAM (soon)

• Symbol rates / bandwidth• Pulse shape filtering (?)• Carrier Frequency• Power• Payload size• CRC ..

The GNU in RADIO

Documents