Post on 24-Jul-2015
transcript
Nuovo Pignone
Brayton Cycle
Operationg Principle
Main parameters affecting gas turbine performance
Definition of Themodynamic
External Factors
Internal Factors
Turbine Orientation & ISO Condition
Nuovo Pignone
• IT DRAWS IN AIR FROM THE SURROUNDING ENVIRONMENT
• IT COMPRESS IT TO HIGHER PRESSURE
• IT INCREASES THE ENERGY LEVEL OF THE COMPRESSED AIR BY ADDING AND BURNING FUEL IN A COMBUSTION CHAMBER
• IT DIRECTS HIGH PRESSURE, HIGH TEMPERATURE AIR TO THE TURBINE SECTION, WHICH CONVERTS THERMAL ENERGY INTO MECHANICAL ENERGY THAT MAKES THE SHAFT REVOLVE; THIS SERVES, ON THE ONE HAND, TO SUPPLY USEFUL ENERGY TO THE DRIVEN MACHINE, COUPLED TO THE MACHINE BY MEANS OF A COUPLING AND, ON THE OTHER HAND, TO SUPPLY ENERGY NECESSARY FOR AIR COMPRESSION, WHICH TAKES PLACE IN A COMPRESSOR DIRECTLY WITH THE TURBINE SECTION
• IT EXHAUST LOW PRESSURE, LOW TEMPERATURE GASES RESULTING FROM THE ABOVE-MENTIONED TRANSFORMATION INTO THE ATMOSPHERE.
Nuovo PignoneP
RE
SSU
RE
TE
MP
ER
AT
UR
E
ATMOSPHRIC LEVEL
TEMPERATURE
PRESSURE
INLET
COMPRESSORCOMBUSTOR
EXHAUST
TURBINE
Nuovo Pignone
The thermodiynamic cycle of a gas turbine is known as the BRAYTON CYCLE.
The following diagram is useful to understand the meaning of the thermodynamic cycle more easily.
1
2 34
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
Nuovo Pignone
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
P
V
T
S
11
1
2
2
2
3
3
3
4
4
4
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
Wc
Wt
Q1
Q2
HR
Nu
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
)( 12)( 12TTcWc TTpm
Mesured in
airinletkg
Kj
_
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
)( 43)( 43TTcWt TTpm
Mesured in
gaskg
Kj
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
Mesured in
gaskg
Kj
)( 23)(1 23TTcQ TTpm
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
Mesured in
gasehxaustkg
Kj
_
)( 14)(2 14TTcQ TTpm
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
This equation tell us that, by parity of heat Q1, introduced into the combustion chamber by fuel, efficiency will increase as heat Q2 “dissipated” into the atmosphere decreases
1
21 )(
Q
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
Mesured in
cairtinletgasturbineu WGWGN _
Kj
Nuovo Pignone
P
T
V
S1
1
2
2
3
3
4
4
FUEL
COMPRESSOR
COMBUSTION EXHAUST
LOAD
AIR INLET
1
2 34
uN
QHR 1
Heat Rate is the inverse of efficiency, in that it indicates the ratio between thermal energy, resulting from the combustion process, and mechanical energy, obtained on the power shaft.
Nuovo Pignone
P
T
V
S
1
1
2
2
3
3
4
4
In the Brayton Cycle are very important the following parameters:
THERMAL EFFICIENCY
SPECIFIC POWER )( skgKw
FIRING TEMPERATURE 3T
PRESSURE RATIO 1
2P
P
Nuovo Pignone
P
T
V
S
1
1
2
2
3
3
4
4
Section A refers the so called “TURBINE INLET TEMPERATURE”, wich is the average temperature of gas at plane A.
Section C refers to the so-called “ISO FIRING TEMPERATURE”, wich is the average gas temperature at plane C, calculated as a function of the air and fuel flow rates via a thermal balance of combustion according to the ISO 2314 procedure.
The difference in the interpretation of temperatures in section A and B consists in the fact that the section B temperature takes account of mixing with 1st stage nozzle cooling air, wich was not involved in the combustion process, but mixes with burnt gases after cooling the surface of the nozzle.
According to the NUOVO PIGNONE-GENERAL ELECTRIC standard, the temperature that best repreesents point (3) is the one in section B