Post on 27-Feb-2018
transcript
7/25/2019 thermoplastics elastomers
1/35
EXPERIMENT 2
THERMOPLASTIC ELASTOMER BLENDS
INTRODUCTION
1.0 Introduction
Thermoplastic elastomer (TPE) is a new polymer which combine the service
properties of elastomer (vulcanized rubber) and also able to be process as
thermoplastic. This combination of properties can be obtained through simultaneous
presence of soft elastic segments (that have high extensibility and low glass transition
temperature, Tg) and hard segments (which have a lower extensibility a high Tg) and
there are susceptible association to cross!lin"ing.
The toughness of a polymer is described as the ability to resist by absorbing
energy #$% and is therefore a very important material property. &uch research in
polymer field aims at improving the toughness of a material and investigates the
mechanisms by which such an improvement can be obtained.'crylonitrile!butadiene!styrene (') is a widely used thermoplastic. *n ',
acrylonitrile causes an improvement in chemical resistance and weatherability,
butadiene has the character of rubber toughness, and styrene offers glossiness and
processability. The compositions of the various components can be controlled to meet
the re+uirements of a variety of applications. owever, the overall mechanical
properties of ' are lower than those of most engineering plastics, and the heat
distortion temperature of general grades of ' is lower than $--/ (Ping, $001,
/hin and wang, $012). *n order to upgrade the use of ', one simple way is to
blend ' resin with other high performance engineering plastics such as
polycarbonate (P/) #3%.
P/ is an important engineering plastic that is widely used since its
development in $045 and first production in $06-. Polycarbonate!consumption was
7/25/2019 thermoplastics elastomers
2/35
$.$ million tons in $002 and increasing. *ts main features are transparency, toughness
and high!temperature stability applied in car!parts (e.g. headlights), glazing, lighting,
housing for electrical e+uipment, pac"aging (e.g. mil" bottles) or as data!carrier (/7).
To reduce the sensitivity to these conditions, P/ is often blended with
acrylonitrile!butadiene!styrene ('). This can only be done in applications where
the transparent character of P/ is not important. P/8' is one of the most
successful commercial polymer blends. 9irst patents date from $06:. This blend
combines the good mechanical and thermal properties of P/ and the ease of
processability, notched impact resistance and the sometimes lower price of
'.P/8' actually is a ternary blend, since ' itself usually consist of styrene!
acrylonitrile (';) and dispersion of polybutadiene (P). The properties of such
ternary blend will depend on the structure properties of the components #$%.
lends of P/ and ' have been commercially available for a number of
years. P/ can contribute towards improvements in strength, dimensional stability,
heat distortion temperature and impact resistance of the blends.
7/25/2019 thermoplastics elastomers
3/35
CHAPTER II
LITERATURE RE$IE%
2.1 Acrylonitrile Butadiene Styrene (ABS Polymers)
2.1.1 General Introduction
7/25/2019 thermoplastics elastomers
4/35
Acrylonitrile-butadiene-styrene (ABS) has grown to become one of
the most widely used thermoplastic in the world because of the wide
range of available properties, ease of processing, and a good balance
between price and performance.
The ABS resins have well-balanced set of properties for molding
close dimensional control articles with an outstanding surface nishing
good impact resistance, and metal plating characteristics. ABS resins
belong to a very versatile family of thermoplastic polymers. ABS is
produced by combining three monomers! acrylonitrile, butadiene and
styrene. The chemical structure of these monomers re"uires each
monomer to be an important component of the ABS resins. Acrylonitrile
contributes heat resistance, chemical resistance, and surface hardness to
the system. The butadiene contributes toughness and impact resistance,
while styrene component contributes processibility, rigidity and strength.
ABS plastics are two-phase systems. Styrene-acrylonitrile (SA#)
forms the continuous matri$ phase. The second phase is composed of
dispersed polybutadiene particles, which has a layer of SA# grafted onto
their surface. The binding matri$ layer of SA# ma%es this polymer&s two
phases compatible '.
2.1.2Chemistry
7/25/2019 thermoplastics elastomers
5/35
nNC n
n
Acr&'onitri'! But(di!n! St&r!n!
' plastics are two!phase systems. tyrene!acrylonitrile (';) forms the
continuous matrix phase. The second phase is composed of dispersed polybutadiene particles,
which has a layer of '; grafted onto their surface. The binding matrix layer of '; ma"es
this polymer=s two phase compatible #5%.
/ommon types of ' polymers have an average composition of 3$ to 32>
acrylonitrile, $3 to 34> butadiene and 4: to 65> styrene. 'crylonitrile primarily offers
chemical resistance and heat stability, butadiene gives toughness and impact strength and the
styrene commonly provide ' with balance of clarity, rigidity and ease of processing (vec
et al., $00-).
tyrene and acrylonitrile can be copolymerized to form '; copolymers, typically at
a 2-85- ratio of ';. ?i"e polystyrene, '; is a clear copolymer, but with the additional
characteristics of higher chemical resistance, better surface hardness and improved toughness
(Pillichody and @elly, $00-). This copolymer is a commercially significant product, with
maAor applications in mar"ets such as battery cases, disposable cigarette lighters and house
wares.
' polymer systems typically contain between 2- and 0-> ';. *n forming the
continuous phases of ', the '; contributes its characteristics of easy processing, high
strength and rigidity, chemical resistance and good surface hardness and appearance #:%.
7/25/2019 thermoplastics elastomers
6/35
2.1.) Pro*!rti!#
The properties of ' polymers are determined by molecular and morphological
parameters, the matrix composition and molecular mass, the type of rubber, the volume ratio
of the rubber to the continuous phase, the rubber particle size, the grafted rubber structure,
and the additive content are also important #4%.
Table 3.$ summarized the effects, which will occur under some situations. The
properties of this multi!phase system are also affected by conditions at the interface between
the rubber level is extremely important and the maAor trade!offs from the increased rubber
level are shown in 9igure 3.$.
' polymer has low density ($-3- to $-6- "gm !$) and the bul" density of the pellet
is also low, usually 4-- to 6-- "gm !5(Pillichody and @elly, $00-). The material is opa+ue as
a result of the different refractive indices of the two phases. The presence of the polar nitrile
group results in certain affinity of the ' polymer for water or water vapour. 'n increase in
the humidity content will lead to complications in processing and to deteroration in some
properties #:%..
*ncrease molecular
weight of the ';
;arrow molecular
weight distribution
road molecular
weight distribution
*ncrease the content
of elastomers
*ncrease resistance to
surface!active
substances
*mprove dimensional
stability
*ncrease heat and
pressure sensitivity
of the melt
7ecrease heat
deformation
resistance
*mpact strength 7ecrease in *mprove flow *ncrease melt
7/25/2019 thermoplastics elastomers
7/35
increase shrin"age properties viscosity
uppression of creep *ncrease creep
resistance
*mprove the impact
strength
Tensile strength
increase
Tensile strength
increase
'geing resistance
decrease9luidity decrease tiffness increase
Table 2.1 : Effect of molecular characteristics of the elastomer phase and SAN copolymer
forming the matrix (Sec et al.! 1""#$
2.1.).1 M!c+(nic(' Pro*!rti!#
The overall toughness offered by ' materials is the prime mechanical property that
prompts most users to select ' for their applications. The standard measure of impact
strength of used for ' is notched *zod impact strength, as measured by 'T& 7346'.
'lthough ' is notch sensitive, it is much less so than many other polymer, including
Tensile trength *mpact trength
Bigidity /reep strainardness &elt Ciscosity
eat Besistance Thermal
Expansion
&edium igh Cery igh
*mpact *mpact *mpact
*;/BE'*;D BEB ?ECE?
%igure 2.1 : &a'or property tradeoffs for A)S *ith increasing rubber leel.
(+lenn and ,athleen! 1"-$
7/25/2019 thermoplastics elastomers
8/35
polycarbonate and nylon. *n addition to good impact strength at room temperature, '
retains significant impact strength at very low temperature (vec et al., $00-). This has led to
the use of ' in critical low!temperature applications. ' materials can deform in a
ductile manner over board temperature range and at high strain rates.
'nother important characteristic of engineering thermoplastic is their stress!strain
behavior in flexure. 's with tensile properties, the flexural strength at yield and flexural
modulus can be used to determine the resistance of a product to short!term loadings (;obert,
$02$). They also useful in comparing the strength and rigidity of the many ' products #:%.
2.1.).2 T+!r,(' Pro*!rti!#
The critical thermal properties for ' are heat distortion, coefficient of linear
thermal expansion, thermal endurance, thermal conductivity, and specific heat. The most
common measure of heat distortion is the deflection temperature under load as measured by
'T& 76:1. igh!heat ', '8Polycarbonate (P/) alloys, and '8styrene!maleic
anhydride (&') alloys all extend applications of ' into the temperature up to $$-o/ at
$.1 &Pa for short!term exposures (Fen"er and @oln, $015).
*n general, plastics have significantly higher thermal expansion coefficients than
metals. /onse+uently, in applications where parts are constrained, thermal stresses must be
accommodated in part design or expansion may induce failure in the part. This property is
especially important in ' products designed for electroplating (&oh et al., $002).
The thermal properties of ' polymers are characterized mainly by the glass
transition temperature, Tg. 'n increase in temperature of the material leads to a decrease in
7/25/2019 thermoplastics elastomers
9/35
the tensile strength and increase in the ductility and toughness. owever, the modulus of
elasticity in tension decreases (vec et al., $00-) #:%.
2.1.).) R+!o'o-&
9actors influencing melt flow behavior of ' include (&oh et al., $002) G
$. The presence of the grafted rubber domains, their weight fraction, graft to
rubber ratio, particle size distribution
3. The composition, molecular weight and molecular weight distribution of the
matrix
5. 'dditives, ie, lubricants, stabilizers, fillers, pigments, etc
:. Besidual components from the polymerization process and
4. Hater.
The presence of the grafted rubber increases viscosity the viscosity effect increases
with decreasing shear rates and increasing rubber content. Besidual volatile
components and lubricants can function as diluents to reduce viscosity. *t has been
suggested that their influence on viscosity may depend on whether such materials
preferentially reside in the rubber or matrix phase (Dlenn et al., $014) #:%.
2.1.). C+!,ic(' R!#i#t(nc!
The chemical resistance information has been obtained from numerous sources and it
is primarily based on plastic material test specimens that have been immersed in the chemical
(not combination of chemicals) and on field experience. nder no circumstances is to be
assumed that a mixture of individually acceptable chemicals may be safely used with ' or
any other products.
7/25/2019 thermoplastics elastomers
10/35
The effect of the combination of chemical on the ' components has to be assessed
in conAunction with other factors that have a significant impact upon the lifecycle of the
system i.e. temperature, internal pressure, flexural stresses, cyclic loads etc. 'ny chemical
attac" is increased when temperature or stress are increased or when temperature or stress are
varied. Table 3.3 shows the reference for the chemical solvents that may affect the resistance
#6%.
CHEMICAL RESISTANCE
%!(/ (cid# Dood resistance
Stron- (cid# ?imited resistance
%!(/ ('/('i# Dood resistance
Stron- ('/('i# Dood resistance
A--r!##i"! #oi'# Excellent resistance
M!t(' #('t# Dood resistance
S!( (t!r Excellent resistance
Aro,(tic +&droc(rbon# Poor resistance
Or-(nic #o'"!nt# Poor resistance
T(b'! 2.2 R!!r!nc! C+!,ic(' R!#i#t(nc!
2.1. Proc!##in-
2.1..1 3!n!r(' Proc!##in-
' material can be processed by inAection molding, extrusion, blow molding.
owever, inAection molding and extrusion account more than 05> of all ' material usage.
' polymers process very easily and can be fabricated into very complex parts. '
re+uires significantly lower processing temperatures and is less sensitive to processing
conditions (risimitza"is, $00:) #:%.
2.1..2 E4tru#ion
7/25/2019 thermoplastics elastomers
11/35
'n extruder with minimum ?87 ratio of 3:G$ is recommended to ensure a uniform
mixing and melt temperature over the die. ' screen pac" consisting of a 3-!:- mesh
combination is recommended. ingle or two twin screw are suitable. owever, the latter part
is preferred since it also aids in devolatilization and results in an improved extrudate +uality
(Pillichody and @elly, $00-) #:%.
2.1..) In!ction ,o'din-
' polymers can be processed in all types of inAection molding e+uipment, but
optimum results are obtained with reciprocating screw machines since it provides more
uniform melt and higher available pressure. Processing temperatures range from $22 to
311o/, depending on the specific grade. *nAection pressure of 60 t- $51 &Pa and clamp
pressure of 31$ to :33 "g8cm3of proAected part surface are usually sufficient. crew having a
length to diameter (?87) ratio of 3-G$ is recommended (Dlenn and /athleen, $014).
2.1.5 Ad"(nt(-!# (nd Di#(d"(nt(-!#
ABS, being copolymeri*ed from three di+erent monomers, has high
impact strength and competes well with polypropylene although it is more
e$pensive '. ts good dimensional stability ', it replaces die-cast metal
components and can be electroplated. ABS is e$cellent for vacuum-
forming and blow-moulding for the production of articles such as re
e$tinguishers, bus wheel arches, industrial containers, refrigerators shells
and protective helmets. t has good impact resistance (toughness) and
rigidity properties. Basically, ABS is preferred for its favourable balance of
high gloss, colourability, processability and price.
7/25/2019 thermoplastics elastomers
12/35
The balances of properties which are e$hibited by ABS are not found
in any other plastic material. ABS material can be classied as a
lightweight plastic material due to low creep '.
Besides the advantages, the material has also a number of
limitations. The disadvantages are as follows!
$. ?imited chemical resistance to hydrocarbon and concentrated acids and al"alis.
3. ?ow dielectric strength
5.
7/25/2019 thermoplastics elastomers
13/35
/abinets of TCs, Badios, Hall cloc"s, Tape recorders and
/ar stereos.
4. igh eat Besistant Drades 'utomobile components, ousing for electrical heaters I
dryers
6. Transparent Drades sed in areas where high transparency I good impact
strength is re+uired
2. *mpact &odifier Drades &odifier to PC/ compounding industry, covering all types
of formulations!rigid, semi!flexible, clear and opa+ue
1. Dlass 9illed Drades sed in applications re+uiring a very high flexural
strength, stiffness, maintaining the impact and tensile
strength
0. Extrusion Drades Befrigerator linings and luggage
Table 2./ : A)S +0AE3SE A4453,AT36NS
2.2 Po'&c(rbon(t! 7PC8
2.2.1 3!n!r(' introduction (nd Hi#toric(' B(c/-round
Polycarbonate (P/), was first developed in $045 by ayer in Dermany, and Deneral
Electric in the independently. ?EJ'; is its most popular trade name. P/ is a heterochain
polymer featuring high performance that comprise the family of Kengineering
thermoplasticsL. P/ is an excellent material choice as it is not Aust high!performing but also
can be recycled and be produced in an eco!friendly manner.
' P/ molecule includes a isphenol ' part and a carbonate group. isphenol ' has
two aromatic rings rendering P/ high strength. *t does not crystallize easily due to the
isphenol group. The polymer attains its transparency due to this amorphous structure. The
characteristic high glass transition temperature (Tg M $:4o/) of P/ is caused by the minimal
molecular rotation about the bonds #1%.
7/25/2019 thermoplastics elastomers
14/35
O
O
O
CH3
CH3
n
Bi#*+!no' A C(rbon(t!
2.2.1 C+!,i#tr& (nd M(nu(cturin-
2.2.1.1 C+!,i#tr&
P/ is most often synthesized from isphenol ' and phosgene by a step!growth
polymerization in which /l!ions are eliminated every time the monomers react. This "ind of
step!growth polymerization is often called a condensation process #1%.
$. Polymerization teps
! The isphenol ' group are reacted with proton acceptors such as ;a
7/25/2019 thermoplastics elastomers
15/35
isphenol ' odium 7isphenolate ion of
hydroxide bisphenol '
! The deprotonated isphenol ' reacts with Phosgene and a catalyst at
temperatures between 34 and 54o/. this way, a Polycarbonate monomer is
formed, and the catalyst (often times Pyridine), is eliminated along with
the anion.
O-
CH3
CH3
ClCl
O
+
Cl
O
O
CH3
CH3
+
Phenolate ion end phosgene chloroformate end on bisphenol '
on bisphenol '
! *n order to react more isphenol ' and phosgene into the chain, chloride
anions are always eliminated
+
Cl
O
O
CH3
CH3
O-
O-
CH3
CH3
7/25/2019 thermoplastics elastomers
16/35
/hloroformate end of polymer disphenolate ion of bisphenol '
Cl-
O
O-
CH3
CH3O
O
CH3
CH3
+
Polycarbonate polymer being extended
2.2.1.2 M(nu(cturin- o PC
Polycarbonate is transformed from pellets into the desired shape for its intended
application by melting the polycarbonate and forcing it under pressure into a mold or die to
give it the desired shape depending on the application. This process is repeated thousands of
times.
*n the extrusion process, the molten P/ is passed through a die that gives the material
its final shape. 'fter this, the melt is cooled rapidly. ?ong pipes and sheets are created by this
process.
*n the molding process, the P/ melt is pressed into a mold with defined shape of the
final product. The melt is then cooled inside the mold. This process is ideal for specific parts
such as automotive and computer parts #1%.
7/25/2019 thermoplastics elastomers
17/35
2.2.2 Pro*!rti!#
2.2.2.1 P+ic(' (nd M!c+(nic(' Pro*!rti!#
Polycarbonate is a polymer which, when un!crystallized, has excellent transparency.
Hhen thic", it has a slight yellowish tint. The index of refraction of transparent and colorless
P/ is very high, $.41:. the industrial grades of P/ have molecular weights on the order of
3-,--- to 4-,--- g.mol!$. The relative rigidity of the chain causes high viscosity in the li+uid
state.
Polycarbonate has a vitreous transition temperature of about $4- o/ and conse+uently
it is to be used almost exclusively in the vitreous range (great rigidity). 't ambient
temperature (between TN M 1-o/ and Tg M $4-o/). P/ is ductile, which explains in part its
very good resistance to shoc". Polycarbonate has polymers #0%.
! ?ittle elongation relative to rupture,
! Excellent resistance to shoc" even cold,
! ' wide temperature range for use (up to $54o/) sterilization
possible.
2.2.2.2 C+!,ic(' Pro*!rti!#
P/ absorbs only small +uantities of water (O-.6>) and its mechanical properties are
not affected by it. P/ can be used for ma"ing obAects fre+uently washed with hot or sterilized
7/25/2019 thermoplastics elastomers
18/35
water, but a long period of time in hot water (-6- o/) causes a decomposition resulting in a
drop in shoc" resistance.
P/ is not attac"ed by diluted mineral and organic acids. *t is insoluble in aliphatic
hydrocarbons, ether and alcohol. *t is partially soluble in numerous halogenous hydrocarbons.
P/ is attac"ed by strong bases (ammonia). P/ is fairly stable in the presence of ozone.
tability in C light is not exceptional and P/s turn yellow fairly +uic"ly. uitability for
contact with food and physiological innocuousness. P/ is recognized as being suitable for
ma"ing obAects in contact with food. /ertain grades are approved for medical use. P/s can be
sterilized with steam #0%.
2.2.2.) E'!ctric(' Pro*!rti!#
Polycarbonate has good insulating properties little affected by variations in
temperature or humidity.
2.2.2. T+!r,(' Pro*!rti!#
P/ is practically self!extinguishable. Besistance to fire, rated per ?0:, ranges from
to C-!C3 according to type, wall thic"ness and stabilization.
2.2.2.5 Di,!n#ion(' Pro*!rti!#
Polycarbonate, as all un!crystallized polymer, offers limited retraction when molded
(O-.6>)G
7/25/2019 thermoplastics elastomers
19/35
7/25/2019 thermoplastics elastomers
20/35
7/25/2019 thermoplastics elastomers
21/35
and sometimes as KalloysL to borrow a term from metallurgy (&odern Plastic &agazine,
$00:). The need for improved balance of properties and the potential ability of polymer
blends to satisfy this need have converged in the development of polymer blending as a maAor
area for rigorous growth in the past several years. Properties of plastics that have most often
been improved by polymer blending include processability, tensile strength, ductility, impact
strength, abrasion resistance, heat deflection temperature, low!temperature flexibility, flame
retardancy, and environmental stress!crac" resistance #:%.
2..1 ABS B'!nd#
' is itself a blend of P and ';, but can be further blended with other materials
and thus the scope of possible applications is broadened. /ommercial blends with ' are
given in Table 3.5 ('dam et al., $005) and some of these will be discussed in more detail
below #:%.
lend @ey Properties 'pplication Drowth Bate
P/8'
eat resistance, low
temperature impact,
processability, ease of flame
retarding
'utomotive, computer housing,
lawn and garden, power tools,
recreational vehicles
0>
PC/8'
*mpact strength and
toughness, flame retardance,
C stability, processability
Electrical components,
appliances, business machine
housings, housewares
$3!$1>
;ylon8'
igh impact, chemical
resistance, low moisture
sensitivity
'utomotive body panels and
underhood components, vacuum
cleaner housing
2>
TP8'
/hemical and abrasion
resistance, low temperature
toughness
'uto bumper fascia
PT8'
Processability, impact
strength, heat and chemical
resistance
?awn and garden e+uipment,
small appliances, fluid
engineering industry
1>
Polysulphone8'Processability, low cost, heat
resistance, can be plated
'ppliances, auto window handles,
faucets, food trays
T(b'! 2. B'!nd# it+ ABS 7Ad(, et al.! 1::)8
7/25/2019 thermoplastics elastomers
22/35
2..2 Po'&c(rbon(t!;ABS B'!nd#
The second class of alloy is produced through blends made with polycarbonate (P/).
;early all P/8' is used in automotive and business machine applications, with a small
amount in lawn and garden e+uipment, power tools and recreational vehicles. P/8'
properties and price are intermediate between those of the more expensive P/ and the less
expensive '. The blends8alloys of P/8' provide heat resistance as well as low
temperature impact strength and processability. ' improve the processability and reduced
cost whereas the P/ provides the heat resistance and toughness and impact, higher tensile
properties and improved ease of flame retarding (onner and ope, $005). These alloys
exhibit excellent toughness, good heat distortion and high rigidity (Dlenn and /athleen,
$014) #:%.
The commercialization of P/ began in $041 the production of the P/8' blends
started on $022. The addition of ' to P/ minimizes its drawbac"s without affecting its
superior mechanical properties, and also generates other useful characteristics, such as
glossiness and low temperature toughness. ' number of patents concerning these blends have
been issued in the past, but the scientific "nowledge about their behaviour is still limited
owing to the complexity of the system. The blends consist, in fact, of four polymeric species
and three phases, their morphology depending on a variety of factorsG molecular
characteristics of the components, ' composition, blend composition, rheological
properties, processing conditions, thermal treatments, etc. P/ and ' are fairly similar in
polarity, and might be compatible with each other the ' grafted rubber (butadiene)
particles chains would remain insoluble, but firmly bonded by their styrene!acrylonitrile side!
chains, producing good physical properties #$-%. 'ssuming this fundamental basis for semi!
7/25/2019 thermoplastics elastomers
23/35
compatibility, it is interesting to determine simultaneously the behavior of the modulus and
the impact strength of the blends versus the P/ content.
CHAPTER III
METHODOLO3 of
P/ blends into '. 9or the modulus of elasticity, the value were decrease to 3$-.05 &Pa as
the increasing amount of P/ blend added into the ' with compatibilizer. Hhen the
addition of '; into the '8P/ blends, it will offers high tensile strength, highest impact
resistance, unfortunately, the modulus of elasticity will decrease. These statement can be
proved in 9igure :.$.$.3.
CHAPTER $
Figure 4.1.$ : Effect of Blend Ratio on Elongation at Break of AB!"# blend
7/25/2019 thermoplastics elastomers
31/35
CONCLUSION
5.1 CONCLUSION
The obAective of the experiment is to analyse the effect of compatibilizer on the
properties of '8P/ blend. ased on the result, both tensile strength and modulus of
elasticity increased with the increasing of P/ content in '8P/ blend. Hith the increasing
of P/ content in '8P/ blends, elongation at brea" for '8P/ blends generally increased.
9urthermore, with the addition of the compatibilizer such as '; will gives an effect on
'8P/ blend. 'lthough the tensile strength and elongation at brea" shows an increment
value, the modulus of elasticity will decrease as the content in the blend will have continuous
phase.
RE@ERENCES
7/25/2019 thermoplastics elastomers
32/35
#$% &.".F. 'nberg ($))1,April*.Fracture of polycarbonate!AB Blends. +niersity of T-ente, Te
/eterlands
#3% 0. ean &-u ($))2,Aug,11*.&echanical 4roperties of 7igh 3mpact A)S84, )lendsEffect of )lend 0atio. 3epartment of "olymer Engineering, Faculty of #emical and/atural Resources Engineering. +niersiti Teknologi %alaysia, 151) +T% kudai,
&oor Baru.
#5% E. Alfredo #ampo. 'ndustrial "olymer.
#:% "% 3r A6man 7assan, "% 3r arir 7asim, #.au en ($))8, %arc*.
&echanical! ,hemical and %lammability 4roperties of A)S849, )lends.&ABATA/
9E&. ";'%ER, FA9. 9E&. 9'%'A 3A/ 9E&. +%BER A;', +T% 9+3A',
&7R.
#4% Acrylonitrile
7/25/2019 thermoplastics elastomers
33/35
CHAPTER TITLE PA3E
TITLE PA3E
LIST O@ TABLES
LIST O@ @I3URES
I INTRODUCTION
$.$*ntroduction
$.3
7/25/2019 thermoplastics elastomers
34/35
5.$ &aterial
5.3 lend Preparation
I$ RESULT AND DISCUSSION
:.$ Besult
:.$.$ Effect of P/ /ontent on Tensile trength and Roung
&odulus
:.$.3 Effect of P/ /ontent of Elongation at rea"
:.$.5 Effect of '; on '8P/ blends
$ CONCLUSION
4.$ /onclusion
RE@ERENCES
LIST O@ TABLES
TABLE No. TITLE PA3E
3.$ Effect of molecular characteristics of the elastomer phase
and '; copolymer forming the matrix (vec et al., $00-)
3.3 Beference /hemical Besistance
3.5 'bs Dradewise 'pplications
3.: lends with ' ('dam et al., $005)5.$ Batio of polymer blend
:.$ Tensile result of different ratio blends
LIST O@ @I3URES
@I3URE No. TITLE PA3E
7/25/2019 thermoplastics elastomers
35/35
3.$ &aAor property trade!offs for ' with increasing rubber
level. (Dlenn and /athleen, $014)
:.$.$ Effect of Blend Ratio on Elongation at Break of AB!"#
blends:.$.$.3 Effect of lend Batio on &odulus of Elasticity '8P/
blends
:.$.3 Effect of lend Batio on Elongation at rea" of '8P/
blend