Post on 04-May-2018
transcript
Turtle Mountain Ordnance Plant 213 First Street NW Rolla Rolette County North Dakota
PHOTOGRAPHS HISTORICAL AND DESCRIPTIVE DATA
HISTORIC AMERICAN ENGINEERING RECORD National Park Service
Great Plains Systems Support Office 1709 Jackson Street
Omaha, Nebraska 68102
HAER No. ND-10
)
Location:
Date of Construction:
Present Owner:
Present Use:
Significance:
Historians:
)
HISTORIC AMERICAN ENGINEERING RECORD
TURTLE MOUNTAIN ORDNANCE PLANT (William Langer Jewel Bearing Plant)
HAER No. ND-10
213 First Street NW, Rolla, Rolette County, North Dakota.
USGS Rolla Quadrangle, Universal Transverse Mercator Coordinates: 14.5411930.454480.
1953 (Modified in 1954, 1957, 1966, and 1988).
Microlap Technologies, Inc. 213 First Street NW Rolla, North Dakota 58367
Manufacturing facility for jewel bearings and related precision components.
The Turtle Mountain Ordnance Plant is significant as the only large-scale, diversified manufacturing facility for the production of jewel bearings in the United States. Jewel bearings were considered a product critical to American military needs during the early and middle years of the Cold War, and the Turtle Mountain plant was established through a federalprivate partnership specifically to address this defense concern. Thus, the plant is also a significant reflection of American logistical responses to perceived Cold War security threats.
Dale Martin, Mitzi Rossillon, and Mark Hufstetler, Renewable Technologies, Inc., February 1997.
I. HISTORY
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 2)
A. JEWEL BEARINGS: DESCRIPTION, MATERIALS, USES
Jewel bearings are very small discs fixed in positions where they support and guide moving pivots
of sensitive, light-load, low-torque instruments and control devices (see figure #1). The important qualities
of jewel bearings are low coefficient of friction, nonmagnetic properties, and great hardness. The hardness
is essential for resistance to wear under constant use and an ability to bear loads heavy for their small size.1
Jewel bearings are usually made from corundum, a mineral (aluminum oxide) with a hardness of 9
on the Moh' s Hardness Scale (the diamond is the hardest mineral in the scale with a rank of 10). Rubies
and sapphires are precious natural forms of corundum, colored red and blue respectively, by metallic
impurities in the aluminum oxide.2 Until the beginning of the twentieth century, all jewels were made from
stones found in nature.
Synthetic gems are industrially-made stones with the same chemical composition (aluminum oxide)
as those created in nature. Manufactured gems quickly and completely replaced their natural predecessors
in bearings, since they cost less and had better grain and fewer flaws. Over ninety years ago, the
Frenchman Auguste Vemeuil invented a process for manufacturing synthetic corundum. In a Vemeuil
furnace, finely powdered aluminum oxide fell through a very hot hydrogen-oxygen flame, melted and then
solidified on a pipe-clay stem below. The resulting product was a "boule," a tapered cylinder of ruby or
sapphire. 3 Boules were the beginning point for making industrial jewels.
The creation of synthetic corundum and its manufacture into bearings served first the watch
making business and then the defense industry. Switzerland, center of the world's watch industry by the
mid-nineteenth century, also became the location of virtually all synthetic jewel manufacture before 1940. 4
By the mid-twentieth century, bearings from synthetic jewels also came to be essential components of
modem military equipment such as airplanes, missiles, ships, and tanks. In the mid-l 950s, a typical
American fighter airplane had 1,500 to 2,500 jewel bearings, while a battleship had about 5,000. In these
vessels, jewel bearings were required for instruments as diverse as clocks, compasses, gyroscopes,
altimeters, range finders, bombsights, electrical controls, and a wide variety of gauges. A bombsight alone
required 250 to 350 jewel bearings.5
.. -:::rf:\:\i:\:i:,
111i1111111i1i1\1i1i1\1w1i\11111111i1\1111\111ii\
VEE JEWEL
~lll\l\llllll\\\\l\~ [\l. RING JEWEL (bar hole)
~i;1;1i1l1l1l1~1~1lw r:l;l;i;l;\;\;i;\1\1
RING JEWEL (olive hole)
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-IO
(Page 3)
Jewel Shapes sections, no scale
midi) BOMBE RING JEWEL (cup, olive hole)
RING BEARING ASSEMBLY
pivot
11 11111:11111:1:111 \ CUP JEWEL
t\l\l\lll\l\l\l\!\llll!llll\lllll\l\l\l\lllllllllllllll ENDSTONE
-~, f\\b BOMBE RING JEWEL (bar hole)
oil
-- endstone
-- setting
Figure# I. Common Jewel Bearing Forms.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 4)
B. WAR THE UNITED STATES, AND JEWEL BEARINGS
For all its economic wealth and diversity, the United States has relied historically on other nations
for nearly all of certain commodities and manufactured goods. This reliance on imports has caused anxiety
and dangerous shortages during wars and disruptions of international trade. During the two world wars,
the United States found it necessary to rush to develop its own supplies and processing of a variety of
materials whose foreign sources were threatened, for instance, potash in Nebraska and chromium in
Montana. Such operations typically could not exist financially outside of the special circumstance of
national emergency. Most were uneconomical in terms of quality of resources, scale of operations,
location, or labor costs, and relied on temporarily high prices or government economic intervention. When
the wars ended, these industries, like a large standing army, were typically abandoned or dismantled. 6
Producers and consumers found this sequence of events undesirable for several reasons: it was expensive,
did not allow immediate product availability, and created a boom/bust economic cycle in the producers'
communities. One perceived solution to these difficulties was the implementation of strategic stockpiles.
The United States established stockpiles beginning in 1940 to accumulate and store essential commodities,
from which to draw when war stopped trade.7
The experience of the United States with jewel bearings in the first half of the twentieth century is
illustrative of war-time shortages. During both world wars, warring nations encircled neutral Switzerland
and the export of Swiss bearings to the United States stopped. American manufacturers pursued several
alternatives. They used Montana sapphires and glass substitutes, tried but failed to create and work
synthetic jewels, and smuggled Swiss jewels in diplomatic pouches. Immediately following World War II,
the Cold War brought fears of another possible halt to Swiss supplies. 8
The Second World War ended with the two greatest powers, temporary allies, quickly resuming
former confrontational attitudes. The United States and the Union of Soviet Socialist Republics (USSR),
both with great resources ofland, population, and industry, embraced conflicting ideologies that led them
into geopolitical strategies involving many nations around the world. 9 In the late 1940s, a series of events
prompted and then escalated Cold War tensions. The USSR took over almost all the nations of central
Europe from which its armies had driven the Germans during World War II, controlling a buffer region on
its historically vulnerable western edge. Meanwhile, the U.S. President enunciated the "Truman Doctrine"
of support for anti-communist forces around the world, initially in Greece and Turkey. 10 The Soviets tested
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 5)
an atomic bomb, ending the U.S. monopoly on nuclear weapons. Wisconsin Senator Joseph McCarthy
began his short, brutal campaign of seeking communists in the U.S. government. Some government leaders
came to believe that the world faced a long-term, widespread struggle between two implacable powers.11
America's responses to the perceived Soviet threat included :fielding worldwide armed forces and
greatly increased military spending.12 Reactions also ranged over a wide variety of smaller subjects. A few
planners thought about creating a source of jewel bearings safe from the Russian tanks that might sweep
from Germany to the Atlantic Coast of France. This thinking eventually led to the small town of Rolla,
North Dakota.
At the beginning of the 1950s, the U.S. government determined to set up its own plant to make
jewel bearings. A variety of reasons were behind this decision. Domestic manufacturers of jewels
maintained only small, limited operations that provided only a tiny percentage of the demand of the nation's
watch and instrument makers. Rapid technological change in the previous decade made most of the
stockpiled supply obsolete. Earlier unsuccessful attempts to quickly create a temporary skilled work force
emphasized the need for a permanent, trained labor pool. The Soviet Union made the same decision; by the
end of the 1950s, it had achieved self-sufficiency in jewel bearings. 13
The U.S. military started with two jewel manufacturing schemes. Work with the Elgin National
Watch Company explored materials, machines, and possible use ofElgin's production facilities in Illinois.
Policy and tactical changes ended this work in 1955-56. Another, more successful effort was arranged
between Army Ordnance and the Bulova Watch Company. 14 It was this partnership that soon found its
way to North Dakota.
C. ROLLA, NORTH DAKOTA, AND JEWEL BEARINGS
Rolla is a small farm town in north-central North Dakota, just ten miles from the Canadian border
(see figure #2). It is the seat of Rolette County, with a 1950 population of 1,176. The county's economy
is based largely on its rich grain farms; Rolla serves as the county's commercial and civic center.
Rolla also became the site of a government-backed jewel bearing plant through initiatives and
decisions in North Dakota and the nation's capital. Government planners in Washington, D.C. wanted a
location consistent with the policy of strategic industrial site dispersal. This required a place far from
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 6)
CANADA
- ---~---•------ - ---fl7ff/1.J,,_
__ ...1.(.i:31 I ~
~
~ N
I '
Ll
'\ I t' -Vll--~rt
--1----1
I
I
l
L :1 ~ TT~ _c_o u N~Y _J
0 5 10 miles 111 a Mi I
···-···- ··- ua1ia-
• Minot
• Bismarck
NORTH DAKOTA
LOCA T/ON MAP
Figure #2. Locator Map.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 7)
urban and other industrial concentrations. In case of a massive aerial attack on the United States, such a
plant might survive. Rolla clearly met these conditions. It is situated at the center of the North American
landmass, far from potential offshore threats. The plant in Rolla would create a new pool of skilled
workers rather than draw them from an already existing industrial labor force. Rolla's location off the
main routes of the national transportation network was not a problem, for the very small quantities of
incoming materials and outgoing products were easily carried by a few trucks on local roads .15
Coupled with Rolla's ideal geographical position was a contemporary effort to improve the
economic condition of the Indians living near the town through greater employment. Just two miles west of
Rolla is the main portion of the Turtle Mountain Indian Reservation, with its headquarters at Belcourt. In
1950 over 2,800 Chippewas lived on this seventy-two square mile reserve; another 1,600 lived elsewhere in
Rolette County. Although containing a reservation just two townships in area, Rolette County had over 40
percent of North Dakota's Indian population, nearly three times that of any other county in the state.16 Like
Indian populations around the nation, many on the Turtle Mountain reserve experienced high
unemployment, poor living conditions, and failure to share in much of the contemporary national
prosperity.
Two North Dakotans were instrumental in bringing jewel bearing manufacture to Rolla. William
Langer had represented North Dakota in the U.S. Senate since 1941. As a young lawyer entering county
and state politics, he built a reputation as an effective opponent of powerful out-of-state corporations and,
during prohibition, the liquor interests. He developed a flamboyant populist style that excited his
supporters and motivated his opponents to try to literally drive him from elected office, once successfully.
In the U.S. Senate, he continued his populism through support of federal social programs and antipathy
toward foreign entanglements that he felt took resources from domestic programs. Langer owed much of
his great popularity "to his hard work for constituents-'Write to Bill Langer' was a campaign
theme-and to his effective advocacy of agrarian and North Dakota interests in Washington. "17
The other person responsible for the jewel bearing plant being located in North Dakota was John
B. Hart. He was a lawyer in Rolla and the executive director of the North Dakota Indian Affairs
Commission. In the latter role, he was "seeking permanent employment" for the state's Native Americans.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 8)
Langer's staff led Hart, in 1950, to A. Hulen Stuart, chief of the scientific and technical
instruments section of the National Production Authority. They discussed the concerns about the United
States' total dependence on Swiss jewel bearing manufacture, and the lack of a domestic permanent labor
force skilled in making jewel bearings. As initial talks seemed promising, investigators traveled to the
Rolla area for closer examination. Using procedures developed by the Hamilton Watch Company,
examiners tested the Turtle Mountain Indians on their manual dexterity, depth perception, motor
coordination, and other aptitudes required for precision work. They also evaluated their potential for high
productivity, patience with intricate tasks, supervisory capability, and low absenteeism. Once again, the
results were promising.18
In 1952, Hart, Langer, and supporters in Rolla achieved success. In March, Hart presented to a
Domestic Jeweled Watch Movement Industry advisory committee meeting in Washington, D.C. a proposal
for North Dakota Indians to make jewel bearings. Later in the month a selection committee visited Rolla
and Dunseith, west of the Turtle Mountain Indian Reservation. On April 15, the Army notified Senator
Langer' s office that Rolla had been selected as the location of a pilot plant to manufacture jewel bearings .19
The community enthusiastically responded to the possibility of the plant. When the federal
managers announced that local support was important to sustain its initial selection, business leaders in
Rolla quickly called a special meeting and within two hours had pledged $25,000. The money raised was
used to acquire land and erect the first building. 20
Construction ofRolla's Turtle Mountain Ordnance Plant, as it originally was known,21 began in
the autumn of 1952. In early October the Frankford Arsenal in Philadelphia, on behalf of the Army
Ordnance Corps, signed a contract with the Bulova Watch Company to operate the jewel bearing plant, for
$1 per year. The Rolla Civic Improvement Association, Inc. was organized to acquire a site on the west
edge of town from the Rolla Sportsmen's Club, and erect the building. The ceremonial groundbreaking on
October 18 attracted about 2,500 people, including officials from the federal and state governments, the
military, and Bulova. Indian dancers and the Rolla school band performed. Company managers stayed to
supervise construction, and install machinery taken from naval storage and prepared for reuse by the
Bulova plant at Sag Harbor, New York. At the beginning of December, State Employment Service
personnel arrived to start testing job applicants. Those seeking work could be up to fifty years old and a
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 9)
high school education was not required; it was expected that 80 percent would be women. By mid-January
1953, 212 applicants had taken the tests. 22
Applying for work at the plant in the 1950s involved a series of tests and an interview. The State
Employment Service used U.S. Department of Labor tests for aptitudes in spatial and form perception,
motor coordination, and manual dexterity to do a preliminary screening. Passing applicants entered a pool
from which the managers selected candidates. Interested individuals filled out applications, took the
Personnel Research Center (Philadelphia) Personality Test for emotional stability and honesty, and drew
pencil lines through every "a" and "v" in blocks of small letters. An interview by the Assistant Production
Manager followed. Finally a local optometrist administered a series of eye tests.23
In the spring, hiring and manufacturing began. Among job applicants, about six of every seven
were Indians. On March 12, the first two production employees-Dorothy Dauphinais, of Belcourt, and
Mary Vondell, of Rolla-reported for work, drilling holes in jewels. By late April, thirty employees
completed the first batch of about 500 synthetic ruby bar hole bearings. Employment continued to grow,
so that within six months there were about seventy people in the plant. 24
The operators celebrated a successful beginning on "Bulova Day," November 4, 1953. Public and
company dignitaries again congregated in Rolla. Among these was Omar Bradley, just appointed president
of the Bulova Research & Development Laboratories after retiring from four decades of army service,
including World War II high command and heading the Joint Chiefs of Staff. (Later, occasional
celebrations at the plant were called Bulova-Bradley Days.) The public toured the facility. At the same
time, the Rolla Civic Improvement Association announced plans to double the plant area. 25 The expansion
was completed, with landscaping around it, in 1954. A Swiss expert on vee jewels joined the staff that
year.26
D. THE WORKERS AT THE PLANT
Although the Swiss presence at the Turtle Mountain plant apparently was small, it was initially
important. In 1952, Bulova brought in a married couple, Emil and Trudi Schneider, both experienced jewel
bearing workers. Emil first installed machinery and then managed production, while Trudi oversaw the
hiring and supervision of workers. A later Swiss arrival called her "the soul and heart of the operation."
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 10)
The Schneiders left Rolla in 1962. Of the Swiss contingent (unknown size), only Ed Allamand, who
arrived in 1957 and later became the plant manager, remained after the 1960s.27
Making jewel bearings was work with advantages not often found in small towns in rural regions.
In the mid-1950s, Bulova paid workers seventy-five cents per hour, with benefits covering retirement, paid
vacation, and health insurance. This kind of steady work and compensation was rarely found on the farms
and in the small retail businesses of the area.28 Between October 1952 and June 1957, more than one-half
of the total expenditures of approximately $2.5 million on the plant were paid in wages to people in the
county and on the reservation. 29
Through the decades, the work force at the Turtle Mountain plant remained relatively stable in size
and composition. Located in Rolla in large part to employ nearby Indians, Chippewas have consistently
comprised about 60 percent of the employees.30 As predicted when applicant testing began, women
provided most of the labor, or about 70 percent. When Doreen Hudson went to work at age nineteen in
1954, most of her coworkers were "older" women and, like her, married.31 By the mid-1950s, employment
reached a level kept for decades, with about 150 on the payroll. Many stayed at the plant for much of their
working life. Of the approximately 165 employed at the plant in May 1966, 48 had been there since
November 1952. From the early 1960s to the early 1990s, the plant work force remained "unusually
stable," averaging about 143 employees. A majority of workers were between thirty and forty years old;
most had worked there ten to fifteen years. The changes and uncertainties of the mid-1990s (see below)
brought lower levels of employment. The number of non-management workers declined to 119 in July
1994, and then to just 77 two years later.32 While the work force diminished, the proportions of Native
Americans and women among the employees remained stable.33
Work at the Turtle Mountain Ordnance Plant brought economic benefits to a small but significant
proportion of the Indians in the county. The plant employed more Indians than any other single enterprise
in and around the Turtle Mountain reservation.34 While Chippewa workers at the plant represented only
1 Yz percent of the total Indian population of Rolette County, and Indian unemployment in the county has
never fallen below 30 percent, the importance of the plant to area Indians, and especially Indian women,
through the early 1970s is noteworthy. Employment data show that, from the early 1960s through the early
1970s, Indian workers at the jewel bearing plant represented 7-10 percent of all employed Indian workers.
During the same period, about 14 percent of women in the Indian labor force in Rolette County worked at
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 11)
the plant.35 By the mid-1970s, however, these percentages began a rapid decline, so that in 1995 Indian
workers at the Turtle Mountain plant represented only about 3 percent of the county's total Indian labor
force. 36
In addition to the benefits of permanent employment, the early example of Native American labor
at the Turtle Mountain plant helped start a pattern. This was the first known employment of Indians in
manufacturing for government contracts and military goods, and set a precedent for placing many other
such plants on Indian reservations in following decades. In the late 1970s, for example, the Turtle
Mountain Corporation at Belcourt manufactured electronic components for the military, employing
between twenty and sixty workers.37
E. CHANGES AND CHALLENGES OVER THE DECADES
The Turtle Mountain plant has survived changes in levels of military procurement, advances in
instrument technology, challenges to the cost and quality of its products, and questions about Bulova' s
commitment to the operation.
Local fears for the viability of the plant began early. Rolla' s Turtle Mountain Star in 1954
believed that businesses in the United States that wanted lower tariffs on Swiss jewel imports were
circulating "propaganda" to undermine the Rolla plant and its products. Months later, there were worries
that Bulova would not renew its contract on the plant. 38 During the annual shutdown for vacation in 195 8,
some workers heard a rumor that Bulova had come close to permanently closing the plant. 39
When voluntary demand would not support full employment and production at the Turtle Mountain
plant, the government took steps to maintain production. In 1958, a directive from the Office of
Emergency Planning required contractors to use Turtle Mountain jewels in the items they made for military
use. In the 1960s, this directive became law, part of the Armed Services Procurement Regulation (ASPR),
later Federal Acquisition Regulation (FAR). 40 Even then, companies often ignored or evaded these rules,
and enforcement was difficult. A 197 5 independent report to the Bulova company noted that the Turtle
Mountain plant suffered an "image problem," the exact cause of which was unspecified. Also, the
businesses that used jewel bearings resented paying five to ten times the price of imported bearings for
Turtle Mountain plant products and some had doubts about the jewels' quality. Some contractors
reportedly bought the North Dakota bearings as required, but instead put Swiss jewels in their products.41
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 12)
As military equipment construction failed to keep the Rolla plant busy, the U.S. government
bought North Dakota jewel bearings for its strategic stockpile. While the stockpile program was primarily
intended to ensure availability of essential commodities from overseas, it could also serve as a means of
financial support for an operation like the jewel bearing plant. By buying bearings when contractors'
orders were low, the stockpile kept the plant busy and its labor force exercising its skills. 42
The technology of instruments and control devices changed radically in the 1970s, reducing the
need for jewel bearings. 43 Jewels were an essential part of the analog method of measurement and control.
In this, continuous mechanical or electrical quantities such as gear speed or voltage proportionally
represented elements such as time, temperature, or altitude on gauges and dials calibrated with fixed scales.
Dozens of jewel bearings were required for such devices, with all their internal gears and display needles.
This changed with the culmination of a revolution in electronics and the digital form of information, in
which data of all sorts could be conveyed through discrete electromagnetic memories in binary code.
Watches, meters, gauges, and control devices could be made without gears, pivots, needles, and other
moving parts which required bearings. While sapphire bearings are still a part of contemporary industrial
instruments and military equipment-for example, gyroscopes and analog instruments for emergency
backup use-much of their former necessity has vanished. 44
Even as new technology supplanted many jewel bearings, the Turtle Mountain plant considered
expanding its jewel business. The plant at Rolla sought new products and markets beginning in the 1970s.
Bearings ordered from and made at Rolla fell from just under 2 million in 1969, to about 1 million a year
later, to one-half to three-quarters of a million for each of the following four years. 45 The managers of the
Turtle Mountain plant responded by making the first jewels for uses other than bearings in July 1973. In
1976 Bulova submitted a proposal to the GSA to manufacture jewel blanks-from which bearings were
made-at Rolla. Twelve years later, with the final addition to the factory, this finally became reality (see
below). 46
By the 1990s, the range of products had grown to include spacers for insulation in microwave
components, rods and pins for lasers, and windows for infrared sensors and ultraviolet filters. The Turtle
Mountain plant gained about 30 percent of the market in sapphire and ruby orifices (nozzles) used in water
jet cutting. Production also expanded into work on materials other than synthetic sapphire and ruby,
including spinel (magnesium aluminum oxide), carbide, and ceramic tubular ferrules, the latter used for
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 13)
fiber optics. 47 The manufacture of dosimeters, small instruments which warn the bearers of exposure to
dangerous radiation, was tried at Rolla. For this purpose, a separate building about 1 mile from the main
plant was constructed in 1982. The Gulf War of 1990-91 resulted in a short-lived surge of orders,48 but
production ceased soon thereafter. Today jewel bearings, once the mainstay of the plant, represent only
about 15-20% of the total plant product.49
In the early 1990s, the impetus for the development of new products was an indication that federal
government support of the facility was about to end. By 1990, the Department of Defense's Inspector
General concluded that the Turtle Mountain plant produced more bearings than needed for ever-diminishing
demand, at higher costs than private vendors, and that contractors were still evading the legal mandate to
purchase Turtle Mountain bearings. The report recommended closing the plant and ending mandatory
purchase by military manufacturers of bearings made in Rolla.50 In 1994, the U.S. government made the
last purchase of jewel bearings for the stockpile, ending four decades of reliable income for the plant. Like
thousands of publicly-owned or government-supported enterprises around the world in the 1980s and
1990s, the Turtle Mountain plant faced the new world of privatization. 51 To aid in the transition to private
ownership, a $4.5 million appropriation from Congress funded the study of new markets and physical
adaptation of the plant.52 On September 27, 1996, Microlap Technologies, Inc. acquired the building and
equipment, and now operates the facility.53
Military need for jewel bearings made in the United States had almost disappeared when the end of
the Cold War altered American foreign policy. Events in the Soviet Union in the mid- l 980s, and the
dissolution of the USSR itself in 1991, ended even the perception of a communist threat. 54 The military
and its demands for weapons technology did not disappear, of course. U.S. concerns, including control of
petroleum reserves in southwest Asia and small hostile nations with possible nuclear weapons, kept military
spending high. Jewel bearings, however, were no longer a strategic concern, due to the lessened need for
jewels and to a perception that foreign sources were under less of an international threat.
F. SIGNIFICANCE
The significance of the Turtle Mountain plant is largely dependent on its uniqueness. It often has
been stated that the Turtle Mountain plant is unique for being the only jewel bearing manufacturing facility
in the United States, North America, or even the western hemisphere. Further, in its first years, it was cited
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 14)
as the only complete jewel bearing manufacturing plant outside of Switzerland and a few other nations in
western and central Europe.55
These claims of uniqueness are more or less correct, although the early history of jewel
manufacture in the United States is more complicated than they suggest. The industry in the early 1950s
had a small but growing presence. From 1950 to 1953, domestic production grew from 3.3 million finished
jewels to 15.7 million, then fell to 10.5 million in 1954. That year at least eight firms, almost all in
industrial centers of five states and often in watch-making towns, reported production. (By way of
comparison, in its first five years of production, from March 1953 to early 195 8, the Turtle Mountain plant
produced over 5 million bearings.)56
The nature of jewel production at other domestic plants in the early 1950s is unclear. Ed
Allamand, long-time Turtle Mountain plant manager, believes that the other firms reporting making jewel
bearings in the United States at the time did not have "true manufacturing" operations. Instead, they relied
on imported, partially-worked jewels and did limited touch-up and finishing work. 57 Whether the only "true
manufacturer" of jewels or instead one of several, the plant at Rolla soon distinguished itself as "the only
large-volume integrated domestic source of jewel bearings" in the United States. In 1959, it produced all
but 11,000 of the more than 2 million sapphire bearings made in the United States.58 According to Willy
Gyger, a Swiss technician installing machinery at the plant in 1966, the Turtle Mountain facility was the
only jewel bearing manufacturing plant in North America and one of the few in the world which made a
wide variety of bearings from start to finish. Gyger said that most European facilities specialized in a
limited range of jewels or steps of manufacture.59
Whatever the validity of conflicting claims, the plant in Rolla is unusual for its small-town setting
in a largely rural state, the majority of Indians in the labor force, and its history of government creation and
support. The Cold War era has left many marks on the American landscape, from prairies dotted with
missile silos to a few surviving bomb shelters in residential backyards. In a small town on the Great Plains,
an ordinary light-industrial building housing Chippewas, farm women, and Swiss immigrants making tiny
rings of synthetic jewels may be one of the most unexpected.
II. PHYSICAL PLANT
A. BUILDING HISTORY AND DESCRIPTION
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 15)
The Turtle Mountain plant continues to operate at its original location, but the size and
configuration of the plant facility have changed dramatically over the facility's lifetime. The plant began as
a 40-foot by 100-foot rectangular metal building, manufactured by the Butler Manufacturing Company of
Kansas City, Missouri. (For several decades, the Butler company has been a major supplier of
prefabricated steel buildings for industrial and agricultural uses.) Rolla business leaders, responsible for
erecting a suitable structure to house the plant, found an available Butler building in Fargo, from where it
was dismantled and trucked to Rolla for reassembly.60 This original building was steel-framed, with
corrugated metal siding and a gable roof. The fenestration pattern featured banks of multi-pane windows
along the long elevations, with doors centered in the ends. In 1954, a second corrugated metal building,
nearly identical to the first, was installed along the south elevation of the original structure, effectively
doubling the plant's size (see figure #3; HAER photograph ND-10-1). By 1957, a third structure was
added, again similar to the first two; this increased the plant's total interior area to 12,000 square feet.
This ad hoc assemblage of buildings continued to house the Turtle Mountain plant into the early
1960s. In May 1963, however, Congress appropriated funds to construct a "permanent building" at Rolla,
as well as purchase new manufacturing machinery for the plant. Three years later, on May 28, 1966-a
"Bulova-Bradley Day"-the $1.15 million project was dedicated. The remodeled facility presented a
dramatically different appearance. A modem addition to the original structure, built at a cost of $700,000,
wrapped around the existing plant on the east and southeast sides. The flat-roofed addition was virtually
windowless, constructed with load-bearing cinder block walls and a brick exterior veneer. The remodeled
building housed $335,000 of new "automatic" manufacturing equipment imported from Switzerland.,
which would reportedly allow for a tripling of production, and the use of more efficient processes. In
addition to these capital costs, $95,000 was set aside for future renovation and equipment purchases.61 At
completion, the building had a floor area of about 30,000 square feet. 62
The plant largely retained its 1966 appearance until 1988, when additional space was needed to
house the manufacture of jewel blanks. This resulted in the completion of a 2,000-square-foot addition,
matching the 1966 building mass in design and materials. Approximately 4,000 square feet of the 1950s
portion of the building was simultaneously rehabilitated.63 The three gable roofs of the 1950s plant were
'66
I 1953
I
'53 I I
----------! I
'54 I I I
:- -- - - - - - - -: '57
r-------- - - - __J
1966
'66
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 16)
® '53
'54
t-----------
'57
1957
'53
- - - - - - - - - - -, I
'54
I ,- - - - - - - - -- - - _J
I I
'66
I '57 I L I
'66 I - - - T - - - _J
I '88 I
1988
Sequence of Plant Expansion schematic plan
Figure #3. Turtle Mountain Ordnance Building Expa11Sion.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 17)
covered with a new shallow-pitch roof superstructure, although some of the original steel walls remained
visible.
Today, the plant is a melding of 1950s, 1960s, and 1980s construction (see figure #4), but most of
the facility's exterior continues to convey its 1966 appearance. The 1966 construction is characterized by
a flat roof and cinder-block walls with an exterior veneer of wire-decorated orange-tan brick. The
corrugated steel walls identifying the 1950s building masses remain visible only on the west comer of
current building. (The 1988 renovations were of a relatively minor scale, and were designed to visually
blend with the 1966 building mass.)
The main axes of the plant building are oriented northwest-southeast and northeast-southwest; the
southeast fa9ade contains the primary entry and is the "front" of the building (see figure #4). There are
metal-framed windows on the front elevation, illuminating the main entry area and a small portion of the
offices (HAER photographs ND-I 0-2 and 3). Above the main entry doors, a mosaic pattern of white,
black, and orange tiles forms a Thunderbird design; this is the only significant visual detail in the building
exterior.
The building's other walls are almost wholly unadorned. Other than on the front elevation, all
brick walls are windowless. There are doors on the southwest elevation, and the northwest facade has a
freight door and dock and a brick chimney (HAER photograph ND-10-5). At the west comer, portions of
the original 1950s plant remain visible; this area features corrugated steel walls with 9-light, metal-sash
hopper windows (HAER photographs ND-10-5 and 6). The three parallel steel gable roofs which once
characterized the 1950s buildings are now covered by a recent windowless half-story, supported on tapered
I-beams, with a gable roof of very low pitch.
The building's interior reflects its utilitarian, manufacturing function. Floors are covered with tile.
Cinder-block walls and modem drop ceilings are evident in most areas, although the 1950s building masses
retain their original gabled ceilings. Interior doors are wood.
The plant is surrounded by paved parking lots, lawns, and rock gardens, all enclosed inside a
chain-link security fence. Just outside the fence are two small storage buildings, a fuel tank inside a dike,
and more lawn.
'Tj ..... (IQ i:: >-1 (1)
=It: .+a>,
""l:t ..... a 'Tj ..... 0 0 >-1
"'C ..... ~
(81 g'ij~d)
~ I~ I ~i1 I N I ~ I N I I N
0
:.E:.J ..... J4-rt iJ O>
co r ..... ;llo,
O>
~8
[ 0,
;:i,
01-aN ·oN }EIVH
N .......
N co
w co
~ 0
lNV'ld '.~[)NVN01IO NN lNf10Jt\l 3'1lfilU
r: J r 1
w N
w .....
w w
w
:i:, ;llo,
w ..... O> CJ'I
;llo, w 00 N
~ t w
;llo, -.ti
CJ'I
Room
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 19)
Key to Figure 4.
Function Room Function
plant floor 24 restroom
office II 25 restroom
restroom 26 sickroom
cafeteria 27 generator room
lobby 28 (empty)
office/reception 29 employee lounge
office 30 acid bath
restrooms 31 plant floor
office 32 machine shop
conference toom 33 shop office
library 34 purchasing
computer center 35 purchasing
sales, marketing, shipping 36 conference room
acid wash 37 research and development
gauge calibration 38 laundry
pre-polishing, tumbling, sorting 39 inventory lock-up; air make-up room
shower 40 final inspection; production and inventory
storage II control
packaging
II 41 final inspection
research and development lab 42 boiler room
blanks manufacturing 43 janitor's room
air conditioning 44 chemical storage
lockers 45 cloakroom
46 air make-up room
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 20)
B. OVERVIEW OF PLANT NAMES, OWNERSHIP, SUPERVISING AGENCIES
The jewel bearing plant has had various names, owners, and responsible government agencies. It
was officially called the Turtle Mountain Ordnance Plant from its founding until 1966, when an act of
Congress renamed it the William Langer Jewel Bearing Plant. Recently, as part of privatization, the
plant's name has been changed to Microlap Technologies/William Langer Jewel Bearing Plant.
At the beginning, the facility was under the jurisdiction of Army Ordnance, acting on behalf of all
the armed forces, in the Department of Defense. In 1957, budgetary constraints led Army Ordnance to tum
the operation over to the General Services Administration (GSA), while retaining inspection
responsibilities. In April 1964, the Rolla Civic Improvement Association, which until then held title to the
land on which the plant stood, sold the land and buildings to the GSA for $18,437.50.64 The GSA returned
the plant to the Department of Defense in 1988, as part of the Defense Logistics Agency and its field
operation, the Defense National Stockpile Center. 65 Through all these changes of government management,
the Bulova Watch Company was the operating contractor. Bulova withdrew from the operation in 1995.66
As stated above, Microlap Technologies, Inc. acquired the building and equipment in 1996, and currently
operates the plant.
III. THE MANUFACTURE OF JEWEL BEARINGS
Many different jewel bearings have been made at the Turtle Mountain plant. The most common
basic type is a disc of corundum with a cylindrical hole at the center (see figure #1). 67 Variation within this
type results from treatment of the hole and the exterior surfaces. The hole of a finished ring jewel has one
of several profiles: (1) with the same inside diameter along its short length (bar hole jewels), (2) with
conical enlargements widening at each end, or (3) with oliving. In the last, the hole in elevation cross
section has two convex sides closest at the middle of the hole, like olives not quite touching. Modifications
to the outside surfaces of jewels may include bevels (chamfers) on the outside diameter, cups or
countersinks around the hole, or bombes (radii) on the upper surface. Other basic jewel types are not
pierced by holes. A vee jewel has an indentation of v-shape on its upper side to hold the end of a pivot. A
cup jewel has a hemispherical depression for a ball pivot.
Depending on the type of jewel produced, there is considerable variation in the tasks performed and
the machines and supplies used. Variations also may be due to the size of the hole in the center of the
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 21)
jewel, the number of jewels ordered by the buyer (and consequently worked at the same time), the fineness
of surface polishing required, or other factors. 68
There also have been changes in jewel manufacture over time. Techniques observed at the plant in
1996 are somewhat different that those employed in the past. This is due to two main factors: the
installation of new machinery from time to time, and the change in product emphasis over the last ten years.
The first machinery installed at the plant had been used by contractors for the U.S. Navy during
World War II and stored afterwards at Naval Supply Depots in Utah and Pennsylvania. Bulova's plant at
Sag Harbor, New York inspected and prepared the machines for use at the Turtle Mountain plant.69 These
machines remained in service until a major revamping of the plant in the mid- l 960s, when apparently all
except the drilling machines were replaced. Most of the new machines were stock equipment of Swiss
manufacture. Meyer & Burger A.G. made much of the new equipment, but other Swiss manufactures
included Werner Zaugg, Otto Sallaz, Gerber Lyss, Guignard Pollens, Berney, Stocker & Cie, and F.
Chapatte.70 With minor exceptions, the Swiss machines remain in use at the Turtle Mountain plant.
However, newer equipment, such as an outside diameter grinding machine made by Schaefli Engineering,
has been added within the last ten years.
In addition to the stock equipment, many machines at the plant either have been fabricated or
modified at the on-site machine shop. Generally, the "home-made" equipment was built either because the
machines were not available at the time they were first needed or because available items did not perform
the tasks desired. For example, most of the large hole-opening machines have been made on-site because
the only available machines opened just small or medium holes. Also, the plant's machine shop has
routinely modified stock equipment to fit the needs for a particular order (HAER photographs ND-10-28
and 29).71 Finally, virtually all machinery maintenance and repair has been and continues to be conducted
on-site, and even some production supplies are made at the plant. For example, workers make stepped wire
for enlarging holes (HAER photograph ND-10-30), while the shop machines the lap plates to which jewels
are cemented for brushing and polishing (HAER photograph ND-10-31).
The second factor resulting in a different in manufacturing techniques over time is the change in
product emphasis, most notably within the last ten years. The plant's change in focus from jewel bearings
to products such as windows and ceramic ferrules (HAER photographs ND- I 0-25 and 27) has involved the
acquisition of new machinery, inspection equipment, and manufacturing techniques.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 22)
The physical layout of the Turtle Mountain plant does not reflect a clear, schematic plan of
materials flowing through a line of sequential work stations (see figure #5). Due to the varied product
types and the fact that jewels themselves have little bulk, locating each manufacturing, washing, and
inspection station next to the preceding step is neither as essential nor as possible as it would be in
traditional heavy industry plant. The circuitous route that jewels take from the blank stage to the finished
product is illustrated by the addition of cupping to bar hole jewels. A worker walks from the outside
diameter station, past the brushing and polishing station, to access the cupping area of the plant. After
cupping, however, another worker must re-trace her co-worker's steps to deliver the jewels to brushing and
polishing.
The following description covers the manufacture of ring or hole jewels at the Turtle Mountain
plant (see figure #5). It identifies the techniques used, especially from the mid-I960s to the late 1980s, to
produce the simplest form of jewel.72
Work begins with blanks, very small flat plates of synthetic corundum. Until 1988, most of the
blanks were supplied by Swiss companies, including Stettler A.G. and Comadur S.A. When the plant
expanded in 1988, a blank manufacturing area was added where boules (globular cylinders of synthetic
corundum; see above) are cut into blanks (HAER photograph ND-10-26). The process of blank
manufacture is not described here due to its recent addition to the plant.
The first step in jewel manufacture is to prepare the blanks for drilling. Blanks are pasted to the
ends of small steel rods (HAER photographs ND-10-7 and 8). When the plant first opened, all blanks were
pasted by hand. But within a short time and certainly by 195 7, automatic pasting machines fabricated at
the plant had been installed. These were replaced in about 1965 by pasting machines manufactured by
Meyer & Burger A.G. These Meyer &Burger machines continue to be used today, with minor exceptions.
(Blanks with an outside diameter greater than 4 mm are pasted by hand, however.) After pasting, the
blanks are moved to the drilling machines where a hole is drilled into the center of each jewel (HAER
photographs ND-10-9 and 10). The drills are World War II machines manufactured by unknown parties,
and slightly modified over time. Each machine consists of an array of 26 drills, the bits of which are
tungsten-carbide wire. The drills turn up to 30,000 revolutions per minute while the pasted blanks are
moved slowly into the bits (HAER photographs ND-I 0-9 and 10). When a comparatively large hole in the
®
0 25
ft
,-
--i
I [ ,-J
L
drill
ing
1
[' I
brus
hini
:] &
pol
ishi
ng
vee
jew
els
r r
lapp
ing
[I I
--i.
.._
i._
I
~ I
.r; ' 7
Typ
ical
Rin
g J
ewel
1
1 P
rod
uct
ion
Pat
h
ve
e je
wel
s c: 0
& c
uppi
ng
~is
"'F&
n I
I L
C: (
/)
·-.s
final
in
spe
ctio
n
8
hole
op
enin
g 2
0)
C:
·c:
0 .c
1.
Dri
llin
g
t .
&
. .
2.
Hol
e O
pe
nin
g
coni
ng
ol1~
ng
t la
ppin
g
brus
hing
&
po
lish
ing
7
4 in
-lin
e in
spec
tion C
l C
: ~
ro E
ou
tsid
e
Q)
:i
dia
me
ter
... ... 5
~
3.
Aci
d W
ash
*
t 4.
In
-Lin
e In
spe
ctio
n ~
t 5.
O
uts
ide
Dia
me
ter
t 6.
O
livin
g
t 7.
B
rush
ing
& P
olis
hing
t 8.
F
inal
Ins
pect
ion
* A
cid
Wa
sh i
s re
peat
ed
aft
er
mo
st p
roce
du
res
**
In-L
ine
In
spe
ctio
n
occ
urs
as
need
ed
Fig
ure
#5.
Pro
duct
ion
Wor
k S
tati
ons
and
Dia
gram
for
Man
ufac
ture
of O
live
Hol
e Je
wel
s.
-, § ~ a;::
0 i 0
~ E3 i~
,_ z
O
"'C
9 ,~
, Jc;
.
"'C
;~~
.._
, 0
-,
TURTLE MOUNT AlN ORDNANCE PLANT HAER No. ND-10
(Page 24)
jewel was required, the holes are bored with broaches (rotating enamel and diamond abrasive sticks)
instead of drilled. Meyer & Burger boring machines are used.
The drilled (or bored) blanks are moved to the hole-opening section of the plant. To prepare for
hole-opening, the blanks are strung on a wire by hand. Each string is then encased in either black wax (for
larger jewels) or Wood alloy (a metallic compound that melts in boiling water; for smaller jewels), a
process called investing (HAER photograph ND- I 0-12). Each string of drilled or bored blanks then
usually passes through two hole-opening machines (HAER photograph ND-10-14). Depending on the size
of the desired hole, the string may pass through a set of two small (0.25 mm or less in diameter), medium
(0.25-0.65 mm), or large (over 0.65 mm) hole-opening machines. Each machine includes two spools which
pull a wire back and forth through the holes. The wire is diamond-dust encrusted and stepped, becoming
gradually larger in diameter as the blanks are worked to the end of the operation. This particular operation
has benefitted from some of the most significant improvements and innovations. Meyer & Burger hole
opening machines for small and medium holes were installed at the plant in the mid- l 960s. Also, a
W emer Zaugg machine was installed, perhaps at about the same time, as one of the first ( of two in a series)
hole-opening machines. Because there were no large hole-opening machines available at the time updated
equipment was added to the plant in the mid- l 960s, the machine shop at the plant built "long benches" and
the "rocket launcher" for large hole-opening (HAER photographs ND-10-13 and 15). These operate on the
same principal as the smaller machines, but are considerably longer than the others. Unlike the long
benches which lay horizontally, the "rocket launcher" stands inclined slightly off of vertical to reduce the
amount of floor space required for operation.
Next, the jewels pass to the outside diameter station. The purpose of this operation is to shape the
outside diameter of the jewel, both for size and to insure that the hole is centered. Beginning in the mid-
1960s and for an unknown period of time, the work was accomplished by Otto Sallaz Rough Type and
Finish Type Grinders. These machines have been replaced by others manufactured by Meyer & Burger.
All of the outside diameter machines operate in a similar fashion. The jewels are strung on wire which is
held in a bow and moves between two diamond-bonded wheels (HAER photograph ND-10-16).
The jewels then may be moved to the cupping station if the buyer requires such a finish. At this
station, workers may add a cup, bombe (radius), or bevel to the jewel. Broaches abrade the jewels to form
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 25)
the desired shape. This step is accomplished by Meyer & Burger machines, either D.C.1 or Creusomat
models, depending on the desired finish.
At the next station, jewels are brushed and polished. To prepare the jewels for brushing and
polishing, they are blocked or cemented with rhodopas (a synthetic varnish) on a cast-iron disc or plate
(HAER photograph ND-I 0-17). The jewels on the plate are first brushed and then polished on one side,
and then blocked again for brushing and polishing on the opposite face (HAER photograph ND-10-18).
The brushes may have bristles of metal, animal hair, or rice-all encrusted with diamond dust. The
brushing machines were manufactured by Gerber Lyss, and apparently date to the mid-l 960s. Jewels may
be pre-polished using the Guignard Pollens machine, a type of grinding wheel. They are fine-polished or
lapped by Berney Polishing Machines. (The Berney machines also are used for stock removal, i.e., prior to
drilling when the blanks are substantially thicker than required for the finish product.) Rotating plates
under the rotating diamond-dusted polishers provide the final burnish to the outside surfaces (HAER
photograph ND-10-18).
If the jewels require olive (or cone) holes, they are moved to the next station, where they are strung
by hand preparatory to oliving. Briefly during the 1960s, a Stocker & Cie Loading Machine was used to
string the jewels, but the machine was found to be more complicated than stringing by hand and was
abandoned quickly. One of two oliving machines may be used. The first is a semi-automatic oliving
machine manufactured by F. Chapatte. The other was made at the plant by the machine shop. In this
particular machine, the diamond-dust encrusted string wire is affixed to a bow which is moved back and
forth at an angle to create the olive shape in the hole (HAER photographs ND-10-19 and 20). The jewels,
held apart from each other by nylon strings, are rotated around the string wire by rolling on a small flat
belt.
After most steps, the jewels are washed-boiled in a mixture of sulfuric and nitric acid, rinsed in
water, and dried-to ensure clean pieces for the next step (HAER photograph ND-10-11 ). There is also
frequent visual inspection under magnifying glasses or projected images, and precise measuring of the
partially-completed jewels (HAER photograph ND-10-24). These inspections are called in-line inspections
and often occur at benches between stations.
After the jewels are completed, workers take them to the final inspection room where they are
examined before transferred to the shipping department. Inspection is accomplished by workers using
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 26)
magnifying loops, and more recently by microscopes and computer equipment (HAER photographs ND-
10-21 and 22).
IV. NOTES
1. Randall P. Cameron, Jr., "Jewel Bearings-Precision Components for Quality Equipment," Product Engineering 24 (August 1953): 186-191; "The Fulfillment of Essential Jewel Bearings Requirements to Meet a National Emergency," a report to the Honorable Frank B. Ellis, Director of the Office of Emergency Planning, by the OEP Advisory Committee on Jewel Bearings, 13 November 1961, 11-12, 14 (hereafter cited as "Jewel Bearings Requirements"). A detailed technical report covering design, applications, and production of jewel bearings is "A Report on Jewel Bearings: Turtle Mountain Plant, Rolla, North Dakota," [by Bulova Watch Co., New York, 1962] (hereafter cited as "A Report on Jewel Bearings"). (All of the above are located in the offices of the Microlap/William Langer Jewel bearing Plant, Rolla North Dakota.)
2. George Letchworth English, Getting Acquainted with Minerals (New York: McGraw-Hill Book Co., 1934), 31, 131; Frederick H. Pough, A Field Guide to Rocks and Minerals 4th ed. (Boston: Houghton Mifflin Company, 1976), 112-113.
3 .. B.W. Anderson, Gemstones for Everyman (New York: Van Nostrand Reinhold Company, 1976), 314-16; "A Report on Jewel Bearings," 40, 42.
4. Encyclopedia Americana, 1993 ed., s.v. "watch"; "Basic Technical and Production Data, Jewel Bearings: Turtle Mountain Ordnance Plant, Rolla, North Dakota, Volume I" (report prepared by the Bulova Watch Company, New York, for U.S. Army Ordnance Corps, Philadelphia, [1958]), 6. [MS 10497 in the special collections of the State Historical Society of North Dakota, Bismarck] (hereafter Volumes I and II are cited as "Basic Technical Data," I: or II:).
5. "Jewel Bearings for Defense" (Turtle Mountain Ordnance Plant promotional pamphlet, undated [ca. 1956]).
6. James C. Olson, Histo:1:y of Nebraska, 2d ed. (Lincoln: University of Nebraska Press, 1966), 271; GCM Services, Inc., "Cultural Resource Inventory and Evaluation of the Benbow Mine and Mill and the Mouat Mine in the Stillwater Complex, Stillwater County, Montana" (Butte: for the Montana Department of State Lands, 1990), 9, located at Montana Department of Environmental Quality, Helena.
7. Simone K. Leyva, "A Program Evaluation of the William Langer Jewel Bearing Plant" (report for PA 631 and PA 694, Troy State University, 1 September 1994), 5; U.S. Department of the Interior, Bureau of Mines, Minerals Yearbook, 1942 (Washington, DC: Government Printing Office, 1944), 20-26.
8. "Jewel Bearings Requirements," 12-13, 19; "Basic Technical Data," I: 6-8.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 27)
9. Walter LaFeber, America, Russia, and the Cold War, 1945-1984, 5th ed. (New York: Alfred A. Knopf, 1985), 1-28; H.W. Brands, The Devil We Knew: Americans and the Cold War (New York: Oxford University Press, 1993), v-viii, 3-4, 218-19. On the potential political and economic usefulness of the Cold War, see Brands, 34-41, 149.
10. LaFeber, America. Russia, and the Cold War, 29-73.
11. Ibid., 74-124; Ernest R. May, ed., American Cold War Strategy: Interpreting NSC 68 (Boston: Bedford Books of St. Martin's Press, 1993), 1-9.
12. May, American Cold War Strategy, 9-82; LaFeber, America, Russia. and the Cold War, 96-98; Brands, The Devil We Knew, 55. On fears of Soviet invasion of western Europe, see May, 9, 38; LaFeber, 53, 96.
13. "Basic Technical Data," I: 8; "Jewel Bearings Requirements," 7, 13.
14. "Jewel Bearings Requirements," 9-10.
15. "Basic Technical Data," I: 10.
16. U.S. Department of Commerce, Bureau of the Census, Census of Population: 1950, Volume II: Characteristics of the Population, Part 34: North Dakota (Washington, DC: Government Printing Office, 1952), 15, 27, 59.
17. John A. Garraty, ed., Dictionary of American Biography: Supplement Six. 1956-1960 (New York: Charles Scribner's Sons, 1980), s.v. "Langer, William," by David H. Bennett, 360-62. In his first term as governor of North Dakota, in May 1934 a federal grand jury indicted Langer for illegally "soliciting funds from federal employees for personal and political gain." He was convicted and removed from office. Langer appealed twice and was acquitted in the third trial; he was re-elected governor within four years. Langer died in November 195 9, in his fourth term in the U.S. Senate, and in 1966 an act of Congress named the jewel bearing plant for him. Ed Allamand, who came to Rolla in 1957 to work at the bearing plant, believed that the public explanation of Langer' s crucial role in locating the plant in Rolla was overstated. He stated that North Dakota's junior U.S. Senator in the early 1950s, Milton Young, "did all the work, and Langer took all the credit" (Ed Allamand, interviewed by Mitzi Rossillon, Rolla, 25 June 1996).
18. Turtle Mountain Star [Rolla], 9 October 1952; 27 June 1963, 2. (Unless noted otherwise, all articles in the Turtle Mountain Star are on the front page, with some continuing on the back page.) "Jewel Bearings Requirements," 8-9; "Basic Technical Data," I: 4, 10. For a photo of the North Dakota Indian Affairs Commission-nine white men-see Turtle Mountain Star, 24 September 1953.
19. Turtle Mountain Star, 17 April 1952.
20. Turtle Mountain Star, 8 May 1952; 23 October 1952; 27 June 1963, 2.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 28)
21. Throughout this document, the factory will be identified as the "Turtle Mountain Ordnance Plant" for the sake of consistency, even though the official name was changed in 1966 and again in 1996 (see below).
22. Turtle Mountain Star, 9 October 1952; 23 October 1952; 27 November 1952; 15 January 1953; Allamand, interview, 25 June 1996.
23. "Basic Technical Data," II: 4-8.
24. Turtle Mountain Star, 12 March 1953; 19 March 1953; 30 April 1953; 17 September 1953.
25. Turtle Mountain Star, 29 October 1953; 19 November 1953.
26. Turtle Mountain Star, 18 March 1954; 26 August 1954; 4 November 1954.
27. Allamand, interview, 25 June 1996; Doreen Hudson and Mavis Nurmi, individually interviewed by Mitzi Rossillon, Rolla, 26 June 1996; "Jewel Bearings for Defense."
28. Nurmi, Hudson, interviews.
2 9. "Basic Technical Data," I: 10-11.
30. Allamand, interview, 25 June 1996.
31. Hudson, interview.
32. Dan MacCrindle, interviewed by Mitzi Rossillon, Rolla, 24 June 1996; Leyva, "A Program Evaluation," 8, 13.
33. "Jewel Bearings for Defense"; Minot Daily News, 28 May 1966, 18; Leyva, "A Program Evaluation," 13.
34. Other sources of income on the reserve were lease payments on agricultural land, sand and gravel excavation, and work in the Belcourt business and light industrial district: The Confederation of American Indians, comp., Indian Reservations: A State and Federal Handbook (Jefferson, N.C.: McFarland & Company, Inc., 1986), 210-11. Other than retail enterprises, business employers in Belcourt have included a farm equipment manufacturer and contractors for the U.S. government making electronic components and processing income tax data: North Central Planning Council, "Comprehensive Plan, Volume I: History, Inventory and Analysis" (Devils Lake, North Dakota, March 1977), 105.
35. U.S. Department of Commerce, Bureau of the Census, 1980 Census of Population, Volume 1: Characteristics of the Population, Chapter B, Part 36: North Dakota (Washington, DC: U.S. Department of Commerce, 1982), 82, 141; "Report of Labor Force, Employment, and Unemployment for the Turtle Mountain Reservation," 1964-1965; "Report of Labor Force," 1967-1973, Bureau of Indian Affairs, Belcourt. The 14 percent figure assumes that there were 7 5 Indian women employees at the plant on average from 1965 through 1973.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 29)
36. "Report of Labor Force," 1977-1992; "Indian Service Population & Labor Force Report," 1995, Bureau of Indian Affairs, Belcourt.
37. Ervin H. Dockter, Vocation Development Officer, Bureau oflndian Affairs, to Debra Ann Geiger, North Dakota Indian Affairs Commission, 18 May 1978, Bureau oflndian Affairs, Belcourt, North Dakota; Allamand, interview, 25 June 1996.
38. Turtle Mountain Star, 22 April 1954; 11 August 1954.
39. Allamand, interview, 25 June 1996.
40. "Jewel Bearings Requirements," 14; Leyva, "A Program Evaluation," ii.
41. AM. White and C.S. Peet, "Final Report on Analysis of Uses ofJewel Bearings in United States Government Products" (Battelle: Columbus [Ohio] Laboratories [to Bulova Watch Company], 25 June 1975), ii, 33; Lucette Lagnado, ''Watch on Waste ... The William Langer Jewel Bearing Plant," Investigator (October 1981): 74; Leyva, "A Program Evaluation," ii, 2, Appendix B. None of the sources consulted were specific about the supposed defects in jewels made at the Turtle Mountain plant. One source reported that the rate of defects in 1962 was 1 per 40,000, but there is no indication that the rate either exceeded or was less than that of its Swiss counterparts: "A Report on jewel Bearings," 1.
42. Leyva, "A Program Evaluation," 5; Allamand, interview, 25 June 1996.
43. Leyva, "A Program Evaluation," iii.
44. Ibid., I; MacCrindle, interview, 24 June 1996.
45. White and Peet, "Final Report on Analysis," 29.
46. "Report: Facilities, Equipment and Labor Requirements to Establish and Operate a Pilot Plant Facility for the Manufacture of Jewel Bearing Blanks," submitted by Bulova Watch Company, to General Services Administration, 17 November 1976; "The William Langer Jewel Bearing Plant" (typescript, undated [ca. 1987]), 7, located at Microlap Technologies/William Langer Jewel Bearing Plant, Rolla, North Dakota.
47. "When Precision Counts" (William Langer Jewel Bearing Plant publicity pamphlet, undated [ca. 1995]); MacCrindle, interview, 24 June 1996.
48. Leyva, "A Program Evaluation," 10-11.
49. Ed Allamand, telephone interview by Mitzi Rossillon, 12 February 1997.
50. Leyva, "A Program Evaluation," iii, 13-14.
51. Allamand, interview, 25 June 1996; MacCrindle, interview, 24 June 1996; Leyva, "A Program Evaluation," iv.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 30)
52. Dan MacCrindle, telephone interview by Mitzi Rossillon, 24 February 1997.
53. Ibid.
54. Brands, The Devil We Knew, 194-96, 204-206, 209,212.
55. For examples, see "Basic Technical Data," I:[2]; ''When Precision Counts;" and ''NDCRS Site Form: Architectural Sites" for 32R020, by Rebecca Otto, 3 February 1995.
56. "Basic Technical Data," I:[2]; "Rolla Production Schedule-First Six Month Period" [March-August 1955].
57. Allamand, interview, 25 June 1996.
58. "Jewel Bearings Requirements," 7.
59. Minot Daily News, 28 May 1966, 18.
60. Untitled, typed page of construction plans, 30 October 1952, located at Microlap Technologies/ William Langer Jewel Bearing Plant, Rolla, North Dakota; Turtle Mountain Star, 23 October 1952.
61. Turtle Mountain Star, 27 June 1963, 2; Minot Daily News, 28 May 1966, 18.
62. "The William Langer Jewel Bearing Plant," 1.
63. Ibid., 7.
64. Rolette County Clerk and Recorder, Deed Book 49, p. 99; Deed Book 54, p. 8.
65. "Jewel Bearings Requirements," 11; Leyva, "A Program Evaluation," 5.
66. MacCrindle, interview, 24 June 1996.
67. See note 1 on jewel bearings.
68. Morris Azure, telephone interview by Mitzi Rossillon, 11 February 1997; Ed Allamand, interview, 12 February 1997.
69. Untitled, typed page of construction plans, 30 October 1952; Turtle Mountain Star, 23 October 1952; 27 June 1953, 2.
70. "Operation and Machine Description," undated.
71. Allamand, interview, 12 February 1997.
TURTLE MOUNT A.IN ORDNANCE PLANT HAER No. ND-10
(Page 31)
72. The following description of the manufacturing process is compiled from several sources: "A Report on Jewel Bearings," 44-49; "Olive Hole Jewels" (typescript, with hand-lettered date 10/29/56); "Sequence of Operations - Bar Hole Jewels" (typescript, undated [ca. 1957]); Turtle Mountain Star, 12 March 1953; "Jewel Bearings for Defense;" "Tour Guides Manufacturing Operations Facts Sheet" (typescript, with hand-lettered date 06/15/88); "Operation and Machine Description"; Allamand, interview, 12 February 1997; Azure, interview, 11 February 1997.
V. BIBLIOGRAPHY
A BOOKS
Anderson, B.W. Gemstones for Everyman. New York: Van Nostrand Reinhold Company, 1976.
Brands, H.W. The Devil We Knew: Americans and the Cold War. New York: Oxford University Press, 1993.
Confederation of American Indians, comp. Indian Reservations: A State and Federal Handbook. Jefferson, North Carolina: McFarland & Company, Inc., 1986.
LaFeber, Walter. America, Russia, and the Cold War, 1945-1984. 5th ed. New York: Alfred A Knopf, 1985.
May, Ernest R., ed. American Cold War Strategy: Interpreting NSC 68. Boston: Bedford Books of St. Martin's Press, 1993.
Olson, James C. History of Nebraska. 2nd ed. Lincoln: University of Nebraska, 1966.
Pough, Frederick H. A Field Guide to Rocks and Minerals 4th ed. Boston: Houghton Mifflin Company, 1976.
B. ARTICLES IN PERIODICALS AND REFERENCE WORKS
Bennett, David H. "Langer, William." In John A Garraty, ed. Dictionary of American Biography: Supplement Six, 1956-1960. New York: Charles Scribner's Sons, 1980.
Cameron, Randall P., Jr. "Jewel Bearings-Precision Components for Quality Equipment." Product Engineering 24 (August 1953): 186-191.
Lagnado, Lucette. "Watch on Waste ... The William Langer Jewel Bearing Plant." Investigator (October 1981): 74.
C. NEWSPAPERS
Minot Daily News. May 1966.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 32)
Twtlt: Muw1tai11 Stat [Rulla]. Ap1il 1952-November 1954, Jwie 1963.
D. GOVERNMENT PUBLICATIONS
U.S. Department of Commerce, Bureau of the Census. Census of Population: 1950, Volume II: Characteristics of the Population. Part 34: North Dakota. Washington: Government Printing Office, 1952.
____ . 1980 Census of Population, Volume 1: Characteristics of the Population, Chapter B, Part 36: North Dakota. Washington: Department of Commerce, 1982.
U.S. Department of the Interior, Bureau of Mines. Minerals Yearbook, 1942: Volume I: Metals and Minerals (Except Fuels) Washington, DC: Government Printing Office, 1944.
____ . Minerals Yearbook, 1954: Volume I: Metals and Minerals (Except Fuels) Washington, DC: Government Printing Office, 1958.
E. UNPUBLISHED REPORTS AND MANUSCRIPTS
Note: unless noted otherwise, all are located in the offices of the William Langer Jewel Bearing Plant, Rolla, North Dakota.
"Basic Technical and Production Data, Jewel Bearings: Turtle Mountain Ordnance Plant, Rolla, North Dakota." 2 volumes. Report by the Bulova Watch Company to the U.S. Army Ordnance Corps, Philadelphia, [1958]. (MS 10497 in special collections at the State Historical Society of North Dakota, Bismarck.)
Dockter, Ervin H., Vocation Development Officer, Bureau of Indian Affairs, to Debra Ann Geiger, North Dakota Indian Affairs Commission, 18 May 1978. On file, Bureau of Indian Affairs, Belcourt, North Dakota.
"Fulfillment of Essential Jewel Bearings Requirements to Meet a National Emergency." Report to the Honorable Frank B. Ellis, Director of the Office of Emergency Planning, 13 November 1961.
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 33)
GCM Services, Inc. "Cultural Resource Inventory and Evaluation of the Benbow Mine and Mill and the Mouat Mine in the Stillwater Complex, Stillwater County, Montana." Report for the Montana Department of State Lands, 1990. On file, Montana Department of Environmental Quality, Helena.
"Jewel Bearings for Defense." Turtle Mountain Ordnance Plant promotional pamphlet, [ca. 1956].
Leyva, Simone K. "A Program Evaluation of the William Langer Jewel Bearing Plant." Report for PA 631 and PA 694, Troy State University, 1 September 1994.
North Central Planning Council. "Comprehensive Plan, Volume I: History, Inventory and Analysis." Devils Lake, North Dakota, March 1977.
"Olive Hole Jewels." Typescript, dated 29 October 1956.
"Operation and Machine Description." Individual typed pages, undated.
"Report: Facilities, Equipment and Labor Requirements to Establish and Operate a Pilot Plant Facility for the Manufacture of Jewel Bearing Blanks." Report by Bulova Watch Company to General Services Administration, 17 November 197 6.
"Report of Labor Force, Employment, and Unemployment for the Turtle Mountain Reservation," 1964-1965; "Report of Labor Force," 1967-1992; "Indian Service Population & Labor Force Report," 1995. On file, Bureau of Indian Affairs, Belcourt, North Dakota.
"Report on Jewel Bearings: Turtle Mountain Plant, Rolla, North Dakota." [New York: Bulova Watch Company, 1962.]
"Rolla Production Schedule-First Six Month Period." [March-August 1955.]
"Sequence of Operations - Bar Hole Jewels." Typescript [ ca. 1957].
"Tour Guides Manufacturing Operations Facts Sheet." Typescript, dated 15 June 1988.
[Untitled.] Typed page of construction plans, dated 30 October 1952.
''When Precision Counts." William Langer Jewel Bearing Plant promotional pamphlet [ca.1995].
White, AM. and C.S. Peet. "Final Report on Analysis of Uses of Jewel Bearings in United States Government Products." Report from Battelle: Columbus [Ohio] Laboratories to Bulova Watch Company, 25 June 1975.
''William Langer Jewel Bearing Plant." Typescript, [ca. 1987].
F. INTERVIEWS
TURTLE MOUNTAIN ORDNANCE PLANT HAER No. ND-10
(Page 34)
Note: all conducted by Mitzi Rossillon either in Rolla or via telephone. Tapes of Rolla interviews at Renewable Technologies, Inc., Butte, Montana.
Allamand, Ed. 25 June 1996, 12 February 1997.
Azure, Morris. 11 February 1997.
Hudson, Doreen. 26 June 1996.
MacCrindle, Dan. 24 June 1996, 24 February 1997.
Nurmi, Mavis. 26 June 1996.