Post on 27-Jan-2022
transcript
Operation, Service and Parts ManualService Number A23719 to B22204
U300/UD300 Series Ice Dispensers
208782R03
Model UD300
Model U300Model U300B
Model U300R400A/WModel U300BR400A/W
Model U300R800A/WModel U300BR800A/W
Model UD300R400A/W Model UD300R800A/W
Order parts online www.follettice.com
Single-sided dispensers
Dual-sided dispensers
801 Church Lane • Easton, PA 18040, USAToll free (800) 523-9361 • (610) 252-7301Fax (610) 250-0696 • www.follettice.com
Welcome to FollettFollett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask that you take a moment to review this manual before using the dispenser. Should you have any questions or require technical help at any point, please call our technical service group at (800) 523-9361 or (610) 252-7301.
Before you beginCheck your paperwork to determine which model you have. Following is an explanation of the different model numbers in the U300 series.
Important cautions
• Storage area of dispenser contains mechanical, moving parts. Keep hands and arms clear of this area at all times. If access to this area is required, power to unit must be disconnected first.
• Follett manual load units accommodate most cube/cubelet ices up to 1" square and Follett compressed nugget ice. Crushed, flake, bagged or congealed ice cannot be used. Use of these ices can jam dispenser and void warranty. Separate any “waffle-like” sections of cubes before adding to dispenser. If you have questions concerning your ice type, call Follett’s customer service group at (800) 523-9361 or or ( 610) 252-7301.
• Follett recommends use of an activated carbon filter for units equipped with icemakers.
• Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.
• Ice is food. Follow cleaning instructions to maintain cleanliness of delivered ice.
!
U300BR400ACondenser type – A = air-cooled, W = water-cooled
Remote icemaker(s) capacity and refrigerant – 400 = 400 lbs (181kg)/day, R404A 800 = 800 lbs (363kg)/day, R404A absence of = manual fill unit
B = integral beverage cooling. Absence of a B = no integral beverage cooling.
Approximate storage capacity in lbs
Configuration – U = undercounter single-sided, UD = undercounter dual-sided
2
3
Electrical Specifications – 115V, 60Hz, 1 phase
Single-sided models U300 – dispenser 6.0 ampsU300B – dispenser 7.0 ampsU300R400A/W – dispenser 6.0 amps, icemaker 11.0 ampsU300BR400A/W – dispenser 7.0 amps, icemaker 11.0 amps U300R800A/W – dispenser 6.0 amps, icemakers 11.0 amps eachU300BR800A/W – dispenser 7.0 amps, icemakers 11.0 amps each
Dual-sided models UD300 – dispenser 8.0 ampsUD300R400A/W – dispenser 8.0 amps, icemaker 11.0 ampsUD300R800A/W – dispenser 8.0 amps, icemakers 11.0 amps each
Note: Each icemaker and dispenser require separate circuit with electrical disconnect within 10 feet (6m). Equipment ground required. Standard electrical – 115V, 60 Hz, 1 phase. Max. fuse dispenser – 15 amps; each icemaker – 20 amps.
Plumbing
Dispenser – all models3/4" PVC slip fit bin drain 1" PVC slip fit drain pan drain(s)1" PVC slip fit beverage bath drain (units with beverage cooling only)
Note: Drains must be hard piped and insulated. Maintain 1/4" per foot (6mm per 304mm) min. slope
Icemaker – automatic load models only 1/4" FPT water in1/2" MPT drain3/8" FPT condenser inlet (water-cooled condenser only)1/2" FPT condenser drain (water-cooled condenser only)
Note: Water disconnect within 10 feet (3m) of icemaker(s) is required for automatic load units
U300 series dispensers with remote icemaker(s) require separate circuit and disconnect for each icemaker and dispenser.!
On all models with remote icemaker(s), black wire on icemaker control board LINE VAC terminal must be moved to 24V terminal.!
Do not reduce size of drain lines or tie drains together.!
4
22"(559mm)
30"(762mm)
Beveragelines enterthrough bottom
9"(229mm)
9"(229mm)
15"(381mm)
10"(254mm)
2.5"(64mm)
7"(178mm)
3" (77mm) 2"(51mm)
Junction boxes
32.375"(823mm)
Ice waterbath(U300BR5A/W,U300BR10A/Wonly)
3/4" drain
1" drains
8.5"(216mm)
Ice transporttube entry
27.5"(699mm)
Entrancebeveragelines
Electricconn. 17"
(432mm)
12" min(305mm)
6" min(153mm)
One icemaker –Models U300R5A/WU300BR5A/W
Two icemakers –Models U300R10A/WU300BR10A/W
40.875"(1039mm)
54.875" (1394mm)
25.25"(642mm)
29.625" (753mm)
ICE
Disp.drains
18.875"(480mm)
Dispenser only with no icemakerModel U300/U300B
U300 series single-sided dispensers
Front view
Side view – ice dispense chute
Required clearances:• 60" (1524mm) for installation• 49" (1245mm) for auger removal
12.125"(308mm)
30"(762mm)
8.5"(216mm)
9"(229mm)
9"(229mm)
15"(381mm)
27.5"(699mm)
2.5"(64mm)
2"(51mm)
3/4" drain
ice tube entry
32.375"(823mm)
1" drains
8.5"(216mm)
beveragelines exitthroughbottom ofchase
27.5"(699mm)
10"(254mm)
alt. ice transporttube entry
13.25"(337mm)
13.25"(337mm)
electricconn.
Electricconn.
18.875"(480mm)
17"(432mm)
12" min. (305mm)
6" min. (153mm)
Dispenser with one icemakerModels UD300R5A/W
Dispenser with two icemakersModels UD300R10A/W
Disp.drains
43.875" (1115mm)
54.875" (1394mm)
25.25" (642mm)
29.625" (753mm)
ICE
Beveragelines exitthroughbottom of chase
12" min. (305mm)
Dispenser only with noicemakerModel UD300
UD300 series dual-sided dispensers
Side view - ice dispense chute
Front view
Side view opposite ice dispense chute
Required clearances:• 60" (1524mm) for installation• 49" (1245mm) for auger removal
5
To start up and operate dispenser 1. Follow all cleaning and start-up instructions in U300 Installation Manual packed with dispenser before
operating dispenser. 2. Turn power switches located under dispenser top to ON position. 3. For manual load models, remove drain pan and fill storage area with compatible ice. (See caution on page 2
of this manual concerning ices which may be used in this dispenser.) 4. For automatic fill models, turn icemaker (bin signal) switch(es) located inside dispenser top to ON position
and begin to make ice. 5. When dispenser has at least 6" (153mm) of ice in storage area, press lever or button to ensure that dispenser
is operating properly.
How dispenser worksFollett’s single-sided U300 series and dual-sided UD300 series ice dispensers are available in manual load configurations (using ice from another source) or automatic load configurations (fed from one or two Follett 400 lb/day remote icemakers). An ice water bath beverage cooling system located directly behind valves is available for single-sided U300 series dispensers. Dual-sided units must use a separate mechanical cooling system to cool beverage lines.
In all models, ice is stored below counter in dispenser storage area. When dispense lever or button is pushed, dispense motor is activated. This causes wheel assembly in storage area to rotate counterclockwise, moving ice to vertical auger assembly. Vertical auger carries ice up to dispense chute where it drops by gravity into container.
In automatic load models, ice is manufactured in either one or two Follett remote icemakers. These icemakers may be located up to 20 ft (3m) away from dispenser. As water freezes to inside walls of icemaker evaporator, a rotating stainless steel auger removes ice and carries it to top of evaporator assembly where it is compressed and extruded through an outlet port. The extruded ice is then pushed through tube to storage compartment of dispenser. A bin thermostat shuts off icemaker when storage compartment is full.
Periodic cleaning of dispenser
Solution A: Prepare cleaning solution (200 ppm available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be at 75˚ – 125˚F (23˚ – 52˚C).Solution B: Prepare sanitizing solution (50 ppm available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be at 75˚ – 125˚F (23˚ – 52˚C).
Recommended daily cleaning of drain pan 1. Remove all debris from drain pan. 2. Pour 1 gallon (4L) hot water into drain pan to keep drain lines clear.
Recommended weekly cleaning 1. Remove drain pan(s) and grille(s) and wash with Solution A above. Rinse thoroughly. 2. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in
cleaning Solution A, rinse, sanitize with Solution B and reinstall. 3. Pour a solution of one cup (8 oz/237ml) household bleach mixed with one gallon (3.8L) hot water into drain
pan(s) to help prevent algae growth in drain lines.
Recommended quarterly cleaning (every 3 months) 1. Empty all ice from dispenser. 2. Remove dispenser top and turn bin signal switch(es) and dispenser power switch to OFF position. 3. Remove dispenser drain pan(s) and grille(s). 4. Remove thumbscrews from splash panel, lift up and out at bottom of panel and remove. 5. Remove chute cover(s), dispense chute(s), auger tube and auger (see disassembly instructions).
6
Do NOT run plastic parts (drain pan, dispense chute cover, dispense wheel) through a dishwasher.!
7
6. Remove yoke rods, drive shaft and dispense wheel (see disassembly instructions). 7. Clean all components and bin storage area with Solution A, rinse thoroughly with clear water and sanitize
with Solution B. Caution: To avoid damage to switch, do not immerse chute cover in solution. Wipe only with cleaning cloth.
8. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in cleaning Solution A, rinse, sanitize with Solution B and reinstall.
9. For models with integral ice water bath beverage cooling only: a. Lower Tygon drain tube found on drain connection side of waterbath into PVC waterbath drain and drain
ice water bath. b. Wash bath interior and components with Solution A, using a bottle brush to clean coils. c. Reposition Tygon waterbath drain line in UP position. d. Fill waterbath with Solution A and turn power back on. e. Allow pump to run for 2 minutes to clean pump and pump lines. f. Turn power OFF, drain bath and secure tube in UP position.
Putting unit back in service after quarterly cleaning 1. On units with integral beverage cooling, fill ice water bath manually with potable water. Add ice slowly enough
to avoid spillage over top of waterbath. 2. Reassemble components. 3. For manual load units, turn dispenser power switch to ON position and fill unit with approved ice (see caution
statement page 2). 4. For automatic load units, turn bin signal switch(es) and dispenser power switch to ON position and allow
storage area to fill. 5. When dispenser has at least 6" (153mm) of ice in lower storage area, press dispense button or lever to test
that dispenser is functioning properly.
Quarterly cleaning of icemaker system
Disassembly instructions for periodic cleaning
Dispense chute cover removal 1. Remove dispenser top cover and turn three switches on electrical box OFF. 2. Remove two Phillips head screws from top of black dispense chute cover. 3. Pull chute cover forward and down to remove. 4. On push-button actuated units, disconnect plug on harness.
dispense chute cover (dispense mechanism behind cover)
dispenser top cover (electrical box below)
splash panel
dispense tower (auger and auger tube inside) Front view
drain pan
Units with an icemaker require that icemaker be cleaned at least every three months or more often if local water conditions dictate. Failure to clean icemaker system will result in decreased performance and potential damage to icemaker. Refer to Icemaker Operation and Service Manual for instructions.
!
Gate assembly removal 1. Remove black dispense chute cover. 2. Remove thumbscrews on each side of focus chute
and remove. 3. Remove quick release pins holding dispense gate
assembly and chute. 4. Lift gate up and over hinge tabs, then carefully pull and
tilt to unhook from solenoid link. 5. Pull ice chute toward you to unclip from dimples on
chute mounting bracket. 6. Pull ice chute and gate toward you and out through
panel opening.
Auger and auger tube removal 1. Remove black dispense chute cover, focus chute,
dispense chute and gate assembly. 2. Remove drain pan. 3. Remove thumbscrews from splash guard and remove. 4. Remove thumbscrews from splash panel; lift and pull
forward at base of panel and remove. 5. Unplug auger motor at electrical box. 6. Remove two 1/4-20 bolts holding auger motor to
holddown bracket. 7. Remove two thumbscrews from auger motor stabilizer
bracket and aside. 8. Lift auger motor off. 9. Remove dispense chute mounting bracket assembly. 10. Remove side panel of tower. 11. Remove screw holding top auger tube ring to lower ring. 12. Lift auger out of auger tube. 13. Lift out auger tube, turning as needed to clear rivnuts
on side auger motor mounting bracket.
Dispenser wheel removal 1. Remove dispenser top and turn power switch OFF. 2. Remove drain pan and ice bin access cover below it. 3. Remove splash guard and wheel motor access cover. 4. Remove all ice from bin. 5. Unplug wheel motor at electrical box and remove
ground wire. 5. Remove wheel motor by pulling out two quick
release pins. 6. Lift drive shaft up through hole in countertop. 7. Lift dispense wheel out through drain pan opening.
8
auger motor
wheel motor
auger tube
auger
drive shaft
U300 cutaway – front view
Dispense chute assembly
quick release pins
ice chute
gate assembly gate assembly
ice chute
springs
fixed yoke rods with
brackets (front rod is lowest)
fixed ramped yoke rod with bracket (below rotating drive bar)
mounting bracket
auger tube ring
Front
9
GND L1 L2
CONTROL BOARD
QC1
QC2
QC3
PUMP
WM
AM
QC9
QC10
QC11
QC4
QC5
QC6
QC7
QC8
CONTROL BOARD
QC21
QC18
SOLBATH
BATHSENSOR
QC15
QC14
QC22
QC17
SOLDISP
BATH
SOL
SOL
DISPENSE
24 VAC24 VAC
DISPSWITCH
V V V V V V V V V V
JUNCTION BOX JUNCTION BOX
BLA
CK
BLACK
BLA
CK
PL13
GREEN
PL13
GR
EE
N
GREEN
POWERSWITCH
BLACK
BLACK
BLACK
PL13
WH
ITE
BLACK
WHITE
WHITE
WHITE
WHITE
WHITE
PL9
PL1
PL2
PL9
PL1
PL2
L1
L2
PUMP
WM
AM
TRANSFORMERPRIMARY
SECONDARY (24V)
BLUE RED
BLUE BLUE
BLUE
RED
RED
REDBLUE
BLUE
RED
RED
YELLOW
PL12PL12
PL3
PL3
PL10
PL4
PL4
PL6
PL6
PL10
QC QC
DRAIN PANSWITCH
DISPENSESWITCH
(PB OR LEVER)
TRAN
TRAN
TRAN
TRAN
TRAN
TRAN QC22
QC17
BEVERAGE VALVES
RED
BLUE
BLUE RED
REDBLUEBLUEBLUE
BLUEBLUE YELLOW YELLOW
PL7
PL8
PL7
PL8
PL14PL14
KEYSWITCH
ACCESSORY
DRAIN PANSWITCH
T'STAT1 2 IM#1
BIN
BLU
E
BIN SIGNALSWITCH IM#2
BIN SIGNALSWITCH IM#1
24V JB
24V JB
SIGNAL
IM#1BIN
SIGNAL
INPUT POWER
Wiring diagram Single-sided models with a service number of 5012607 or higher or any model with BLUE circuit board
Temperature lights
Temperature lights provide information on the status of the ice-waterbath. When lighted, the following LEDs indicate:
Low LED: Bath is at optimal temperature for cold drinks.
High LED: Bath temperature is above optimal temperature. The bath will fill with ice for 15 seconds and will then stop for 75 seconds. If temperature is still too high, cycle will repeat.
Error and Low LEDs:After 15 minutes of fill cycling, bath is above 40˚F (4.4˚C).
Error (flashing) LED: Board not receiving signal from sensor.
GND . . . .
PL . . . . . .
AM
WM . . . . .
QC . . . . .SOL . . . .
DISP . . .
IM . . . . . .
TRAN . . .
WHEEL MOTOR
QUICK CONNECT
TRANSFORMERSOLENOID
PLUG
GROUNDDISPENSE
ICE MAKER
AUGER MOTOR
LEGEND
JB . . . . . .JUNCTION BOX
T'STAT . .THERMOSTAT
PB . . . . . .PUSH BUTTON
. . . . .
Wiring diagram – all dual-sided models
L1
INPUT POWER
GREEN
PL13
GREEN
BLK
PL13 POWERSWITCH
WHITE
PL12
L2
PL13WHITE
WHITETB
4
R1
PL2
PL4
BLUE
PL2
PL1
TRANSFORMER 1PRI
R C
SEC24V
RED
PL3 PL3
BLUE YELLOW YELLOW BLUE RED
DISPENSESWITCH #1(PB OR LEVER)
A BR1 TRANS.1
(C)
JUNCTION BOX JUNCTION BOX
TRANS.1(C)
SAFETYSWITCH #1(DP-NO)
QCQC KEYSWITCH
ACCESSORY
BLACK
V V V V V V V V V V
SODA VALVES – SIDE 1BLUE BLK
PL10
PL10
RED
R1(B)
BIN STAT(1)
TRANS.1(R)
BLUE
T-STAT
1 2 BLUE
BIN SIGNALSWITCH IM#1
IM #1 BIN SIGNAL PL7PL7
BLUE YEL
BIN SIGNALSWITCH IM#2
IM #2 BIN SIGNALPL8
BLUE BLUE BLUE BLUE
24V J.B.
24V J.B.
GND
BLK BLKTB
BLKSAFETYSWITCH #1(DP-NO)
BLK BLK
SAFETYSWITCH #2(DP-NO)
BLK
PL12
BLK
7
PL1WM WHTWHTBLK RED
4
R2
7WHT
AM
BLK
BLKBLK
TBTB
R1(6)
6 9
R1
BLUE BLUE
DISPENSESOLENOID #1
PL4
TRANS.1(R)
YEL RED RED
QC
TRANS.1(C)
PL8
RED
TRANSFORMER 2PRI
R C
SEC24V
TB TB
BLUE YELLOW YELLOW BLUE RED
DISPENSESWITCH #2(PB OR LEVER)
A BR2R2
(6)TRANS.2(C)
RED
6 9
BLUE BLUE
DISPENSESOLENOID #2
TRANS.2(R)
R2(B)
PL5
R2
SAFETYSWITCH #2(DP-NO)
QCQC KEYSWITCH#2
BLACK
V V V V V V V V V V
SODA VALVES – SIDE 2BLUE BLK
PL11RED
PL11ACCESSORY
TRANS.2(R)
TRANS.2(C)
BLACK
BLACK WHITE
PL6 PL6
PL5
S
S
10
11
Dispenser troubleshooting guide
Service and partsBefore calling for service 1. Check that ice is in the dispenser and that congealed cubes are not causing a jam. 2. Check that circuit breaker and switches are in ON position. 3. Check that drain pan(s) are on securely. If ajar, neither dispenser nor valves will operate. 4. Check that all drains are clear. For units equipped with Follett compressed nugget icemaker, see Icemaker Operation and Service Manual for service and troubleshooting information.
Symptom
Ice does not dispense when switch is actuated.• Auger motor does not run• Wheel motor does not run• Gate does not open
Ice does not dispense.• Auger motor runs• Wheel motor runs• Gate does not open
Ice does not dispense.• Auger motor does not run• Wheel motor runs
Ice does not dispense.• Auger motor runs• Wheel motor does not run
Warm drinks or soda foaming.
Possible cause
1. Power switch faulty or in OFF position; loose connection.
2. Faulty dispense switch. 3. Faulty transformer/tripped breaker. 4. Faulty fill board. 5. Drain pan ajar. 6. Faulty drain pan safety switch.
1. Loose electrical connection. 2. Linkage problem between solenoid and gate. 3. Faulty solenoid. 4. Faulty fill board.
1. Loose electrical connection. 2. Faulty auger motor. 3. Faulty run capacitor.
1. Loose electrical connection. 2. Faulty wheel motor. 3. Faulty run capacitor.
1. No ice in storage bin. 2. Water drained out of ice-waterbath. 3. Faulty circulating pump. 4. Faulty bath solenoid. 5. Faulty thermistor.
Solution 1. Turn power switch to ON, check
connections. 2. Replace switch. 3. Replace transformer/reset
breaker. 4. Replace fill board. 5. Check pan and reseat. 6. Replace switch.
1. Check connections. 2. Check linkage. 3. Replace solenoid. 4. Replace fill board.
1. Check connections. 2. Check auger motor. 3. Check run capacitor.
1. Check connections. 2. Check wheel motor. 3. Check capacitor.
1. Fill storage area with ice or check icemaker operation. Push
reset on board. 2. Check that ice-waterbath drain
tube is in fixed upright position. Push reset on board.
3. Check pump. Push reset on board.
4. Replace bath solenoid. Push reset on board.
5. Replace thermistor.
If problem persists after following this basic troubleshooting guide, call Follett's technical service department at (800) 523-9361 or (610) 252-7301.
12
Disassembly instructions for service requirements only – NOT required for any cleaning procedure.
Ice water bath pump motor removal 1. Disconnect electrical wires to pump. 2. Remove two screws anchoring pump motor bracket to water bath. 3. Loosen hose clamp on 1" (26mm) Tygon hose at pump
and pull hose free of pump motor. 4. Slide motor and bracket toward center of dispenser
and lift to remove.
Beverage valves not operating.
Ice dispenses without actuation.
No ice in dispenser.
1. Faulty 24V transformer. 2. Power switch faulty or in OFF position. 3. Drain pan switch faulty or not depressed. 4. Beverage key switch locking out access.
1. Front ice gate stuck open. 2. Faulty rear solenoid. 3. Faulty pump/faulty bath temperature
sensor. 4. Linkage pin dislodged or broken. 5. Ice jam in rear chute. 6. Misplaced bath sensor causing jam of
rear chute. 7. Wire off rear solenoid causing ice to
dispense out front when filling bath, without actuation.
1. Power switch in OFF position or faulty. 2. Bin signal switches in OFF position or
faulty. 3. Faulty bin thermostat. 4. Faulty transformer. 5. Icemaker related problem. 6. Faulty or disconnected wiring.
1. Check transformer & circuit breaker.
2. Check power switch. 3. Check switch and placement of
drain pan. 4. Check valve lockout.
1. Adjust gate (contact Follett) 2. Replace solenoid. 3. Replace pump or bath sensor. 4. Check pin and reseat or replace if
broken. 5. Clear ice jam from chute. 6. Remount bath sensor in proper
location. 7. Reconnect wire.
1. Check switch and replace if necessary.
2. Check switch and replace if necessary.
3. Replace bin thermostat. 4. Replace transformer. 5. Refer to icemaker Operation and
Service Manual for diagnosing. 6. Check for power and bin signal on
icemaker pc board.
drain hose pump
Plan view ice water bath
bath sensor
Symptom Possible cause Solution
Parts
ICE
Reference # Description Part # 1 Lid, with graphics, single-sided 501930 2 Lid, with graphics, dual-sided 501931 3 Graphics, “Follett” 501938 4 Access panel, tower, single-sided 501944 5 Access panel, tower, dual-sided 501945 Not shown Cover, ice opening (below drain pan) 501934 6 Drain pan assembly and grille 501935 7 Drain pan, plastic 501936 Not shown Switch, drain pan safety 501318 8 Grille, drain pan 501937 9 Chute cover, dispense, push-button with switch 501957 Not shown Chute cover, dispense, lever 501956 10 Splash guard 501943 11 Thumbscrew, 10/32-1/2, splash guard 501100 Not shown Switch, dispense, PB 502441 Not shown Switch, dispense lever (includes boot and spacer) 501714 Not shown Boot, dispense switch button, lever 501841 Not shown Access cover, wheel motor (behind splash guard) 501932 Not shown Skid 501946 Not shown Carton and fillers 501947 Not shown Lip kit (plastic strip bordering ice bin opening and adhesive) 502285 Not shown Insulation, transport tube (sold by the foot) 501176 Not shown Tube, ice transport, 10 ft 502522 Not shown Tube, ice transport, 20 ft 502523 Not shown Plug 2 lead, male 502333 Not shown Plug 2 lead, female 502334
ICE
12
3 3
4
5
6
6
7
8
9
9
1
Plan view
10 10
13
11
11
11
Single-side dispenser Dual-side dispenser
7 7
1
2
8
10
3
5
4
6
9
1112
13
14 countertop section
4Top view lower ring
Top viewauger tube seal
Front viewauger tube
6
Reference # Description Part # 1 Motor, auger (includes capacitor), 100 RPM* 00918904 *Note: If your machine serial number precedes C69443, then you 2 Bracket, auger motor hold-down 502047 Not shown Bracket, auger motor stabilizer, single-sided models 502060 Not shown Bracket, auger motor stabilizer, dual-sided models 502113 Not shown Seal, shaft, auger motor 501977 3 Auger 501980 4 Auger tube (includes insulation) 502631 5 Insulation, auger tube 502099 6 Ring, auger tube, upper 501939 7 Ring, auger tube, lower 502155 8 Motor, wheel, Brother (includes capacitor) 502657 9 Bracket, wheel motor 501981 Not shown Capacitor, wheel motor, Brother 502658 Not shown Gasket, wheel motor bracket 501982 Not shown Pin, quick release, wheel motor (2 required) 502102 10 Drive shaft assembly, for Brother motor 502630 11 Agitator rods, fixed, front and back 502629 12 Wheel, dispense 501978 13 Bearing plate, bottom auger 501971 Not shown Bearing, bottom, auger 501972 Not shown Agitator rod, ramped 502628 Not shown Bracket, fixed agitator (3 used per unit) 501974 Not shown Thumbscrew, 10/32 x 3/4, fixed agitator bracket (2 required) 501259 14 Tee, drain 502059 15 Thermostat box (includes 500514) 502211 Not shown Thermostat 500514 Not shown Retainer, ice hose (includes 2 thumbscrews) 501764 16 Bracket, ice hose and wheel motor 502050
7
14
5
16
reinforcing tab
15
U300 dispense assemblyside view
U300 dispense assemblytop view
21
4
1
4
6
3
3
7
Reference # Description Part # 1 Manifold, carbonated water (bev. cooled units) 502002 2 Syrup coil 501962 3 Waterbath ice guide assembly 502001 4 Bath sensor 502208 5 Bracket, bath sensor 502210 6 Pump, waterbath 501964 Not shown Manifold, carbonated water (single-side, non-beverage cooled units) 501968 Not shown Tubing, vinyl, 1/2" (13mm) ID x 5/8" (17mm) OD (order by the foot – 5 feet required for bath, 2 feet required for overflow) 501965 Not shown Tubing, vinyl, pump (order by the foot – 3 feet required) 501966 Not shown Syrup tube, insulated, non-bev. cooled units) 501967 Not shown Cap, carbonated water manifold valve fitting 502062
Reference # Description Part # 1 Gate, dispense 501955 2 Linkage pin, gate/solenoid 502096 3 Pin, quick release, 3" (77mm), gate and lever 501949 4 Chute, ice 501952 5 Solenoid 501961 Not shown Boot, solenoid 502098 6 Dispense mechanism assembly 501948 7 Spring, dispense mechanism (1 per side) 501950 Not shown Chute, focus 501954 Not shown Lever, dispense 501953
2
1
63
15
5
4 5
Electrical box All UD300 dual-sided models
Reference # Description Part # 1 Relay, 24V 501826 2 Transformer, 65VA 502058 3 Control box, dual-side models 502049 4 Thermostat 500514 5 Switch, rocker 502209 Not shown Bracket, electric box support 502113 Not shown Keylock switch with leads 501960 Not shown Key, beverage, lock switch 501286
1 2
3 4 5
Electrical box Single-sided models with BLUE circuit board
RESET
POWER
Reference # Description Part # 1 Control board (blue) 502207 2 Stand-off 501959 3 Transformer, 65VA 502058 4 Switch, rocker 502209 5 Control box (includes all components) 502212 Not shown Keylock switch with leads 501960 Not shown Bracket, electric box support 501933 Not shown Thermostat (located behind splash panel in thermostat box) 500514 Not shown Key, beverage, lock switch 501286
1 2
4
3
5
208782R0303/10
801 Church Lane • Easton, PA 18040, USAToll free (800) 523-9361 • (610) 252-7301Fax (610) 250-0696 • www.follettice.com