Post on 08-Feb-2021
transcript
Issue Date: 2016-06-25 Page 1 of 11 Report Reference # E302944-A31-UL2016-07-18
Copyright © 2016
UL TEST REPORT AND PROCEDURE
Standard: UL 60950-1, 2nd Edition, 2014-10-14 (Information Technology Equipment - Safety - Part 1: General Requirements)CAN/CSA C22.2 No. 60950-1-07, 2nd Edition, 2014-10 (Information Technology Equipment - Safety - Part 1: General Requirements)
Certification Type: ListingCCN: QQGQ, QQGQ7 (Power Supplies for Information Technology
Equipment Including Electrical Business Equipment)
Product: Switching AdapterModel: PS65BxxxYyyyyS (xxx=090-150, 180-239, 240-320, indicate output
voltage from 9.0Vdc to 15.0Vdc, 18.0Vdc to 23.9Vdc, 24.0Vdc to 32.0Vdc, the output voltage in volt by dividing 10 in step of 0.1V; yyyy=0100-5300, indicate output current from 0.1A to 5.3A, the output current in milliampere by step of 0.01A; maximum output power is 65.0W)
Rating: Input: 100-240 Vac, 50/60 Hz, 1.5 A;Output: see enclosure 7-01 model list.
Applicant Name and Address: SHENZHEN FLYPOWER TECHNOLOGY CO LTDA2ND BLDG, HAOSHAN LINPOKENG2ND INDUSTRY ZONENANPU RD, SHAJING BAOAN DISTSHENZHENGUANGDONG 518125 CHINA
This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the above referenced Standards. The products have been found to comply with the requirements covering the category and the products are judged to be eligible for Follow-Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on such products which comply with this Test Report and any other applicable requirements of UL LLC ('UL') in accordance with the Follow-Up Service Agreement. Only those products which properly bear the UL Mark are considered as being covered by UL's Follow-Up Service under the indicated Test Procedure.
The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety.
Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL.
Prepared by: Eric Song Reviewed by: Candy Guo
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 2 of 11 Report Reference # E302944-A31-UL2016-07-18
Supporting DocumentationThe following documents located at the beginning of this Procedure supplement the requirements of this Test Report: A. Authorization - The Authorization page may include additional Factory Identification Code markings. B. Generic Inspection Instructions -
i. Part AC details important information which may be applicable to products covered by this Procedure. Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of this Test Report.
ii. Part AE details any requirements which may be applicable to all products covered by this Procedure. Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of each Test Report.
iii. Part AF details the requirements for the UL Certification Mark which is not controlled by the technical standard used to investigate these products. Products are permitted to bear only the Certification Mark(s) corresponding to the countries for which it is certified, as indicated in each Test Report.
Product DescriptionAll electrical components and the transformer are mounted on PWB and housed within an ultrasonic welding plastic fire enclosure. The unit is provided with non-polarized input blades (NEMA plug type 1-15P) and output cord with a connector.
Model DifferencesAll models are similar to each other except for model designation, output current ratings, secondary turns of transformer and secondary regulation components.
See also Enclosure ID 7-01 for details.
Technical Considerations Equipment mobility : direct plug-in Connection to the mains : pluggable A Operating condition : continuous Access location : operator accessible Over voltage category (OVC) : OVC II Mains supply tolerance (%) or absolute mains supply values : +10%, -10% (Declared by
manufacturer) Tested for IT power systems : No IT testing, phase-phase voltage (V) : N/A Class of equipment : Class II (double insulated) Considered current rating of protective device as part of the building installation (A) : 20 Pollution degree (PD) : PD 2 IP protection class : IP X0 Altitude of operation (m) : Up to 2000m Altitude of test laboratory (m) : Less than 2000m Mass of equipment (kg) : 0.23 The product was submitted and evaluated for use at the maximum ambient temperature (Tma)
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 3 of 11 Report Reference # E302944-A31-UL2016-07-18
permitted by the manufacturer’s specification of: 40°C The means of connection to the mains supply is: Pluggable A The product is intended for use on the following power systems: TN The equipment disconnect device is considered to be: Plug The following accessible locations (with circuit/schematic designation) are within a limited current
circuit: CY1 secondary to earth The following are available from the Applicant upon request: Installation (Safety) Instructions /
Manual
Additional InformationRevision in project 4787518690:1. Correction model number from "PS65BxxxYyyyyS (xxx=090-320, indicate output voltage from 9.0Vdc to 32.0Vdc; yyyy=0100-5300, indicate output current from 0.1A to 5.3A); maximum output power is 65.0W" to "PS65BxxxYyyyyS (xxx=090-150, 180-239, 240-320, indicate output voltage from 9.0Vdc to 15.0Vdc, 18.0Vdc to 23.9Vdc, 24.0Vdc to 32.0Vdc, the output voltage in volt by dividing 10 in step of 0.1V; yyyy=0100-5300, indicate output current from 0.1A to 5.3A, the output current in milliampere by step of 0.01A; maximum output power is 65.0W)"2. Add one alternate transformer (model PS65B18-24V) for output voltage 18-23.9Vdc.Additional StandardsThe product fulfills the requirements of: N/AMarkings and instructionsClause Title Marking or Instruction Details Power rating - Ratings
Ratings (voltage, frequency/dc, current)
Power rating -Company identification
Listee's or Recognized company's name, Trade Name, Trademark or File Number
Power rating -Model
Model Number
Power rating -Class II symbol
Symbol for Class II construction
(60417-2-IEC-5172)
Special Instructions to UL RepresentativeInspect the transformer(s) listed in table "Electric Strength Test Special Constructions" per AA1.1- (C):When the tests are conducted at other location, inspect test record and specification sheet provided by the component manufacturer. Verify the specification sheet indicates 100% routine test specified in the table be conducted at the component manufacturer.
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 4 of 11 Report Reference # E302944-A31-UL2016-07-18
Production-Line Testing RequirementsElectric Strength Test Special Constructions - Refer to Generic Inspection Instructions, Part AC for further information.
Model ComponentRemovable
Parts Test probe locationV
rms V dcTest Time,
sAll Models T1 - Primary-Seconday 300
04242 1
Earthing Continuity Test Exemptions - This test is not required for the following models:-
Electric Strength Test Exemptions - This test is not required for the following models:-
Electric Strength Test Component Exemptions - The following solid-state components may be disconnected from the remainder of the circuitry during the performance of this test:-
Sample and Test Specifics for Follow-Up Tests at UL
Model Component Material Test Sample(s) Test
Specifics N/A
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 5 of 11 Report Reference # E302944-A31-UL2016-07-18
1.5.1 TABLE: list of critical components PassObject/part or Description
Manufacturer/ trademark
type/model technical data Product Category CCN(s)
Required Marks of Conformity
Supplement ID
01. Label Interchangeable Interchangeable Minimum 80 degree C, Suitable for its application surface.
PGDQ2/8, PGJI2/8
UL
02. Plastic enclosure Sabic Innovative Plastics B V
EXL9112 (GG) (X)
V-0, 115 degree C, Minimum 1.5 mm thickness. Two parts secured together by ultrasonic welding. See ID 4-01 for details.
QMFZ2 UL E45329 4-01
03. PCB Interchangeable Interchangeable Minimum V-0, Minimum 130 degree C
ZPMV2 UL
04. Appliance Inlet Zhe Jiang Bei Er JiaElectronic Co., Ltd.
ST-A03-002, ST-A03-004, ST-A03-005
2.5A, 250VAC AXUT2/8 UL E225980
04a. Appliance Inlet (Alternate)
Yueqing Huaconn Electronics Co., Ltd.
HC-88 2.5A, 250VAC AXUT2/8 UL E340249
04b. Appliance Inlet (Alternate)
Zhejiang LECI Electronics Co., Ltd
DB-8 2.5A, 250VAC AXUT2/8 UL E302229
04c. Appliance Inlet (Alternate)
Yueqing Yanhui Electronic Co Ltd
DB-14-T 2.5A, 250VAC AXUT2/8 UL E334847
04d. Appliance Inlet (Alternate)
Rong Feng Industrial Co., Ltd.
RF-180 2.5A, 250VAC AXUT2/8 UL E102641
04e. Appliance Inlet (Alternate)
Tecx-Unions Technology Corp
SO-222 2.5A, 250VAC AXUT2/8 UL E220004
05. Fuse (F1) Shenzhen Lanson Electronics Col Ltd
SMT T3.15AL, 250Vac JDYX2/8 UL E221465
05a. Fuse (F1) (Alternate)
Conquer Electronics Co Ltd
MST T3.15AL, 250Vac JDYX2/8 UL E82636
05b. Fuse (F1) (Alternate)
King Wahoo Electronics Co Ltd
KET T3.15AL, 250Vac JDYX2/8 UL E302100
05c. Fuse (F1) (Alternate)
Ever Island Electric Co Ltd & Walter Electric
2010 Series T3.15AL, 250Vac JDYX2/8 UL E220181
05d. Fuse (F1) (Alternate)
Interchangeable Interchangeable T3.15AL, 250Vac JDYX/7 UL
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 6 of 11 Report Reference # E302944-A31-UL2016-07-18
06. Varistor (VR1) (Optional)
Lien Shun Electronics Co Ltd
10D471K, 14D471K
Minimum 300VAC, coating Minimum V-0, 6KV/3KA, minimum 105 degree C
VZCA2/8 UL E315524
06a. Varistor (VR1) (Optional) (Alternate)
Hongzhi Enterprises Ltd.
HEL10D471K HEL14D471K
Minimum 300VAC, coating Minimum V-0, SPD3, minimum 85 degree C
VZCA2/8 UL E324904
06b. Varistor (VR1) (Optional) (Alternate)
Thinking Electric Industrial Co., Ltd.
TVR10471-D TVR14471-D
Minimum 300VAC, coating Minimum V-0, 6KV/3KA, minimum 85 degree C
VZCA2/8 UL E314979
06c. Varistor (VR1) (Optional) (Alternate)
Joyin Co Ltd 10S471K, 14S471K
Minimum 300VAC, coating Minimum V-0, 6KV/3KA, minimum 85 degree C
VZCA2/8 UL E325508
06d. Varistor (VR1) (Optional) (Alternate)
Cerglass MFG Inc 10D471K 14D471K
Minimum 300VAC, coating Minimum V-0, 6KV/3KA, minimum 85 degree C
VZCA2/8 UL E317616
06e. Varistor (VR1) (Optional) (Alternate)
Guangdong South Hongming Electronic Science & Technology Co Ltd
ZVR10D471 ZVR14D471
Minimum 300VAC, coating Minimum V-0, 6KV/3KA, minimum 85 degree C
VZCA2/8 UL E321851
07. Bleeder resistor (R1A, R1B, R1C, R1D)
-- -- Eath rated maximum 3M ohm, minimum 1/4 W.
-- --
08. X-Capacitor (CX1) (Optional)
Cheng Tung Industrial Co., Ltd.
CTX Rated maximum 0.33uF, minimum 250V, 100 degree C, X2 type.
FOWX2/8 UL E193049
08a. X-Capacitor (CX1) (Optional) (Alternate)
Strong Components Co. Ltd
MPX Rated maximum 0.33uF, minimum 250V, 100 degree C, X2 type.
FOWX2/8 UL E230903
08b. X-Capacitor (CX1) (Optional) (Alternate)
Shenzhen Surong Capacitors Co Ltd
MPX/MKP Rated maximum 0.33uF, minimum 250V, 100 degree C, X2 type.
FOWX2/8 UL E314875
08c. X-Capacitor (CX1) (Optional) (Alternate)
Shenzhen Yimanfeng Science And Technology Co., Ltd.
MPX/MKP Rated maximum 0.33uF, minimum 250V, 100 degree C, X2 type.
FOWX2/8 UL E315567
08d. X-Capacitor (CX1) (Optional) (Alternate)
Guangdong Fengming Electronic Tech. Co., Ltd.
MKP-X2 Rated maximum 0.33uF, minimum 250V, 105 degree C, X2 type.
FOWX2/8 UL E345487
08e. X-Capacitor (CX1) Shantou High-New MPX Rated maximum 0.33uF, FOWX2/8 UL E208107
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 7 of 11 Report Reference # E302944-A31-UL2016-07-18
(Optional) (Alternate) Technology Dev. Zone Songtian Enterprise Co., Ltd.
minimum 250V, 110 degree C, X2 type.
08f. X-Capacitor (CX1) (Optional) (Alternate)
Jimson Electronics Co Ltd
MKP Rated maximum 0.33uF, minimum 250V, 100 degree C, X2 type.
FOWX2/8 UL E152288
09. Current-limiting resistor (R11, R12, R13, R14)
Interchangeable Interchangeable Each rated minimum 0.5ohm, 1/4W
-- --
10. Electrolytic Capacitors (CE1)
Interchangeable Interchangeable Minimum 400V, 68-150uF, Minimum 105 degree C.
-- --
11. Bridge Rectifier (BD1)
Interchangeable Interchangeable Minimum 1A, Minimum 600V -- --
12. Transistor (Q1) Interchangeable Interchangeable Minimum 2A, Minimum 600V -- --13. Line Choker (LF1, LF2) (Optional)
Interchangeable Interchangeable Minimum 130 degree C. See supplement 4-02, 4-03 for detail.
-- -- 4-02
14. Photo Coupler (OP1) Bright Led Electronics Corp
BPC-817 Double-protection. Providing 5000 Vac isolation. 100 degree C
FPQU2/8 UL E236324
14a. Photo Coupler (OP1) (Alternate)
Cosmo Electronics Corps
KPC817, K1010 Double-protection. Providing 5000 Vac isolation. 100 degree C
FPQU2/8 UL E169586
14b. Photo Coupler (OP1) (Alternate)
Everlight Electronics Co Ltd
EL817 Double-protection. Providing 5000 Vac isolation. 110 degree C
FPQU2/8 UL E214129
14c. Photo Coupler (OP1) (Alternate)
Lite-On Technology Corp
LTV-817 Double-protection. Providing 5000 Vac isolation. 110 degree C
FPQU2/8 UL E113898
14d. Photo Coupler (OP1) (Alternate)
Shenzhen Orient Components Co. Ltd.
ORPC-817 Double-protection. Providing 5000 Vac isolation. 110 degree C
FPQU2/8 UL E323844
14e. Photo Coupler (OP1) (Alternate)
Ct Microelectronics Far East Ltd
CT817 Double-protection. Providing 5000 Vac isolation. 100 degree C
FPQU2/8 UL E364000
15. Y-Capacitor (CY1) (Optional)
Guangdong South Hongming Electronic
F Rated maximum 2200pF, minimum 250V, 125 degree C,
FOWX2/8 UL E154899
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 8 of 11 Report Reference # E302944-A31-UL2016-07-18
Y1 type.15a. Y-Capacitor (CY1) (Optional) (Alternate)
Jyh Hsu (Jec) Electronics Ltd
JD Rated maximum 2200pF, minimum 250V, 125 degree C, Y1 type.
FOWX2/8 UL E356696
15b. Y-Capacitor (CY1) (Optional) (Alternate)
Hsuan Tai Electronics Co., Ltd.
CY Rated maximum 2200pF, minimum 250V, 125 degree C, Y1 type.
FOWX2/8 UL E199069
15c. Y-Capacitor (CY1) (Optional) (Alternate)
Shantou High-New Technology Dev. Zone Songtian Enterprise Co., Ltd.,
CD Rated maximum 2200pF, minimum 250V, 125 degree C, Y1 type.
FOWX2/8 UL E208107
15d. Y-Capacitor (CY1) (Optional) (Alternate)
Jyh Chung Electronic Co., Ltd.
JD Rated maximum 2200pF, minimum 250V, 125 degree C, Y1 type.
FOWX2/8 UL E187963
15e. Y-Capacitor (CY1) (Optional) (Alternate)
Shenzhen Haotian Electronic Co., Ltd.
HT Rated maximum 2200pF, minimum 250V, 125 degree C, Y1 type.
FOWX2/8 UL E326483
15f. Y-Capacitor (CY1) (Optional) (Alternate)
Nan Jing Yuyue Electronics Co., Ltd.
CT7 Rated maximum 2200pF, minimum 250V, 125 degree C, Y1 type.
FOWX2/8 UL E237728
16. Transformer(T1) Shenzhen He Sheng Long Electronics Co Ltd
PS65B12B (for output voltage 9.0-15.0V,48W) PS65B12A (for output voltage 9.0-15.0V,60W) PS65B24-32V(for output voltage 24.0-32.0V) PS65B18-24V(for output voltage 18.0 - 23.9V)
Class B. see supplement 4-04, 4-09, 4-10, 4-11 for detail.
-- -- 4-04
16-1. Insulation system Shenzhen He Sheng Long Electronics Co Ltd
B88 Class B. OBJY2 UL E314639
16-2. Bobbin Sumitomo Bakelite Co Ltd
PM-9820 Phenolic, minimum 0.45mm thick, rated minimum V-0, 150
QMFZ2 UL E41429
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 9 of 11 Report Reference # E302944-A31-UL2016-07-18
degree C.16-3. Insulation tape P Leo & Co Ltd 1P801, 1P802 130 degree C OANZ2 UL E12617416-4. Coil Interchangeable Interchangeable 130 degree C OBMW2 --16-5. Triple insulated wire
Furukawa Electric Co Ltd
TEX-E 130 degree C OBJT2 UL E206440
16-5a. Triple insulated wire (Alternate)
Totoku Electric Co Ltd
TIW-2 130 degree C OBJT2 UL E166483
16-5b. Triple insulated wire (Alternate)
Totoku Electric Co Ltd
TIW-3 155 degree C OBJT2 UL E166483
16-6. Core Interchangeable Interchangeable Ferrite, overall 28.5 by 20 by 21mm. Provided with two layers of Insulation tape wrapped around core body secondary side.
-- --
16-7. Varnish Hitachi Chemical Co Ltd
WP-2952F-2G 130 degree C OBOR2 UL E72979
16-8. Tube (Optional) Great Holding Industrial Co Ltd
TFL, TFT, TFS 200 degree C YDPU2 UL E156256
16-8a. Tube (Optional) (Alternate)
P Leo & Co Ltd 2T-TFL, 2T-TFT, 2T-TFS
200 degree C YDPU2 UL E176865
17. Heat Sink (HS1) Interchangeable Interchangeable Aluminum, secured to Q1 by screw and soldered to PCB. See supplement 4-05 for detail.
-- -- 4-05
18. Heat Sink (HS2) (Optional)
Interchangeable Interchangeable Aluminum, secured to Q2 by screw and soldered to PCB. See supplement 4-06 for detail.
-- -- 4-06
19. Output Cord Interchangeable Interchangeable Minimum 300V, minimum 80 degree C, minimum 24AWG, marked VW-1 or FT-1. Soldered on PCB with additional glue fixing. Maximum 55 mm length inside enclosure.
AVLV2/8 UL
20. Strain Relief Interchangeable Interchangeable Minimum. V-1, See supplement 4-07 for detail.
QMFZ2 UL 4-07
21. Glue Interchangeable Interchangeable Minimum V-2 QMFZ2 UL22.Mylar sheet ITW ELECTRONICS
COMPONENTS/ FORMEX-(a)(b)(f1)
Black, Rated 105 degree C, V-0, min 0.41mm thickness. See
QMFZ2 ULE256266 4-08
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 10 of 11 Report Reference # E302944-A31-UL2016-07-18
PRODUCTS (SHANGHAI) CO LTD
supplement 4-08 for detail.
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 11 of 11 Report Reference # E302944-A31-UL2016-07-18
Enclosures
Type Supplement Id DescriptionPhotographs 3-01 External view - 01Photographs 3-02 External view - 02Photographs 3-03 Internal view - 01Photographs 3-04 Internal view - 02Photographs 3-05 Internal view - 03Photographs 3-06 Internal view - 04Photographs 3-07 Internal view - 05Photographs 3-08 Internal view - 06
Diagrams 4-01 Enclosure dimensionDiagrams 4-02 Line Choker LF1 Spec.Diagrams 4-03 Line Choker LF2 Spec.Diagrams 4-04 Transformer T1 Spec.Diagrams 4-05 Heat Sink (HS1) Spec.Diagrams 4-06 Heat Sink (HS2) Spec.Diagrams 4-07 Strain Relief Spec.Diagrams 4-08 Mylar sheetDiagrams 4-09 Transformer T1 Spec.Diagrams 4-10 Transformer T1 Spec.Diagrams 4-11 Transformer T1 Spec. revision in project 4787518690
Miscellaneous 7-01 Model difference
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-01
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-02
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-03
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-04
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-05
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-06
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-07
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 PHO-08
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-01
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-02
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-03
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-04
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-04
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-05
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-06
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-07
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-08
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-08
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-09
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-09
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-10
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-10
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-11
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 DIA-11
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 MIS-01
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 MIS-01
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 MIS-01
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 1 of 4 Report Reference # E302944-A31-ULRevision Date: 2016-07-18 Test Record
Test Record No. 1The manufacturer submitted representative production samples of Switching Adapter, Model PS65BxxxYyyyyS for investigation.
Tests performed on Models PS65B320Y2030S, PS65B120Y4000S, PS65B113Y5300S were considered to be representative of Models PS65BxxxYyyyyS (xxx=090-320, indicate output voltage from 9.0Vdc to 32.0Vdc; yyyy=0100-5300, indicate output current from 0.1A to 5.3A).
Unless otherwise indicated, Limits tests were conducted by Emtek (Shenzhen) Co Ltd/Building 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China under TPTDP.
Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL.The following tests were conducted:Test Testing Location/CommentsInput: Single-Phase (1.6.2)Capacitance Discharge (2.1.1.7)SELV Reliability Test Including Hazardous Voltage Measurements (2.2.2, 2.2.3, 2.2.4, Part 22 6.1)Limited Current Circuit Measurement (2.4.1, 2.4.2)Limited Power Source Measurements (2.5)Humidity (2.9.1, 2.9.2, 5.2.2)Determination of Working Voltage; Working Voltage Measurement (2.10.2)Transformer and Wire /Insulation Electric Strength (2.10.5.13)Strain Relief (3.2.6, 4.2.1, 4.2.7)Steady Force (4.2.1 - 4.2.4)Impact (4.2.5, 4.2.1, Part 22 10.2)Drop (4.2.6, 4.2.1)Stress Relief (4.2.7, 4.2.1)Heating (4.5.1, 1.4.12, 1.4.13)Touch Current (Single-Phase; TN/TT System) (5.1, Annex D)Electric Strength (5.2.2)Component Failure (5.3.1, 5.3.4, 5.3.7)Transformer Abnormal Operation (5.3.3, 5.3.7b, Annex C.1)Power Supply Output Short-Circuit/Overload (5.3.7)
Test results are valid only for the tested equipment. These tests are considered representative of the products covered by this Test Report. The test methods and results of the above tests have been reviewed and found to be in accordance with the requirements in the Standard(s) referenced at the beginning of this Test Report.
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 2 of 4 Report Reference # E302944-A31-ULRevision Date: 2016-07-18 Test Record
The following supplements are provided as a part of this Test Record. NOTE: These supplements are only available to the Applicant via the CDA system.
Type Supplement Id DescriptionAttachment 2-01 CRDDatasheet 2-02 Datasheet
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 3 of 4 Report Reference # E302944-A31-ULRevision Date: 2016-07-18 Test Record
Test Record No. 2-- The manufacturer submitted representative production samples of Switching Adapter, models: PS65BxxxYyyyyS for investigation.
-- All models in this report employing the following change:1. Correction model number from "PS65BxxxYyyyyS (xxx=090-320, indicate output voltage from 9.0Vdc to 32.0Vdc; yyyy=0100-5300, indicate output current from 0.1A to 5.3A); maximum output power is 65.0W" to "PS65BxxxYyyyyS (xxx=090-150, 180-239, 240-320, indicate output voltage from 9.0Vdc to 15.0Vdc, 18.0Vdc to 23.9Vdc, 24.0Vdc to 32.0Vdc, the output voltage in volt by dividing 10 in step of 0.1V; yyyy=0100-5300, indicate output current from 0.1A to 5.3A, the output current in milliampere by step of 0.01A; maximum output power is 65.0W)"2. Add one alternate transformer (model PS65B18-24V) for output voltage 18-23.9Vdc.
-- Only limited test should be conducted during this change, test was conducted on model PS65B180Y3610S are considered represent other models.
-- All tests were conducted at EMTEK (SHENZHEN) Co., Ltd.under the TPTDP program. See data sheet for more details.
-- Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. The following tests were conducted:Test Testing Location/CommentsEnd Product Reference PageGeneral GuidelinesPower Supply Reference PageGuide Information Page - Maximum Output Voltage, Current, and Volt Ampere Measurement (1.2.2.1)Input: Single-Phase (1.6.2)SELV Reliability Test Including Hazardous Voltage Measurements (2.2.2, 2.2.3, 2.2.4, Part 22 6.1)Limited Power Source Measurements (2.5)Determination of Working Voltage; Working Voltage Measurement (2.10.2)Heating (4.5.1, 1.4.12, 1.4.13)Electric Strength (5.2.2)Component Failure (5.3.1, 5.3.4, 5.3.7)Transformer Abnormal Operation (5.3.3, 5.3.7b, Annex C.1)Power Supply Output Short-Circuit/Overload (5.3.7)
Test results are valid only for the tested equipment. These tests are considered representative of the products covered by this Test Report. The test methods and results of the above tests have been reviewed and found to be in accordance with the requirements in the Standard(s) referenced at the beginning of this Test Report.
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
Issue Date: 2016-06-25 Page 4 of 4 Report Reference # E302944-A31-ULRevision Date: 2016-07-18 Test Record
The following supplements are provided as a part of this Test Record. NOTE: These supplements are only available to the Applicant via the CDA system.
Type Supplement Id DescriptionDatasheet 2-03 Datasheet
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
File E302944 01-ATT-01
Created by UL Document Assembler 2016-07-19 03:41:17 -05:00
E302944-20160625-DescriptionUL.rtfE302944-20160625-DescriptionUL-Photographs-01.ulgE302944-20160625-DescriptionUL-Photographs-02.ulgE302944-20160625-DescriptionUL-Photographs-03.ulgE302944-20160625-DescriptionUL-Photographs-04.ulgE302944-20160625-DescriptionUL-Photographs-05.ulgE302944-20160625-DescriptionUL-Photographs-06.ulgE302944-20160625-DescriptionUL-Photographs-07.ulgE302944-20160625-DescriptionUL-Photographs-08.ulgE302944-20160625-DescriptionUL-Diagrams-01.ulbE302944-20160625-DescriptionUL-Diagrams-02.ulbE302944-20160625-DescriptionUL-Diagrams-03.ulbE302944-20160625-DescriptionUL-Diagrams-04.ulbE302944-20160625-DescriptionUL-Diagrams-05.ulbE302944-20160625-DescriptionUL-Diagrams-06.ulbE302944-20160625-DescriptionUL-Diagrams-07.ulbE302944-20160625-DescriptionUL-Diagrams-08.ulbE302944-20160625-DescriptionUL-Diagrams-09.ulbE302944-20160625-DescriptionUL-Diagrams-10.ulbE302944-20160625-DescriptionUL-Diagrams-11.ulbE302944-20160625-DescriptionUL-Miscellaneous-01.ulbE302944-20160625-TestRecordUL.rtfE302944-20160625-TestRecordUL-01-Attachments-01.ulb