Post on 06-Jun-2020
transcript
xComfort Room Controller Touch User Manual 0v17_EN
xComfort Room Controller Touch
User Manual
xComfort Room Controller Touch User Manual 0v17_EN ii | P a g e
• For other languages and information about xComfort, visit
www.eaton.eu/xcomfort or www.xcomfort.com or use the QR-code.
• Für weitere Sprachen und Informationen zum xComfort System
besuchen Sie ww.eaton.eu/xcomfort oder www.xcomfort.de oder
verwenden Sie den QR-code
• Besok www.xcomfort.no eller www.eato.eu/xcomfort for andre språk
og mer informasjon om xComfort eller bruk QR-koden.
• Pro další jazyky informace o xComfort návštěvy
www.eaton.eu/xcomfort nebo www.xcomfort.cz nebo použijte QR
kód.
• Voor andere talen en meer informatie over xComfort ga naar
www.eaton.nl/xcomfort of www.xcomfort.nl of maak gebruik van de
QR-code
xComfort Room Controller Touch User Manual 0v17_EN iii | P a g e
Table of Contents 1. Introduction ......................................................................................................................................... 1
1.1 Safety instructions .......................................................................................................................... 1
1.2 Intended use .................................................................................................................................. 1
1.3 Instructions for disposal ................................................................................................................. 1
1.4 About this document ...................................................................................................................... 1
2 The Room Controller Touch .................................................................................................................. 2
2.1 Operation ....................................................................................................................................... 2
2.2 Cleaning mode ............................................................................................................................... 3
2.3 Replacing the batteries ................................................................................................................... 3
2.4 Operation mode ............................................................................................................................. 4
2.4.1 Basic operations ...................................................................................................................... 4
2.4.2 Enhanced operations ............................................................................................................... 4
2.4.3 Settings edit operations ........................................................................................................... 4
2.5 Basic Operating Instructions ........................................................................................................... 5
2.5.1 Show Current Room Temperature ........................................................................................... 5
2.5.2 Show Current/Active Set-Point Temperature ........................................................................... 5
2.5.3 Temporarily adjust the current set-point temperature............................................................. 6
2.5.4 Switch active set-point temperature (operation mode) ........................................................... 6
2.5.5 Show Room Humidity .............................................................................................................. 7
2.5.6 (Optional) Show outdoor temperature. ................................................................................... 7
2.5.7 (Optional) Show Time and Day of Week ................................................................................... 8
2.5.8 (Optional) Touch-button(s) ...................................................................................................... 8
2.6 Enhanced Operating Instructions ................................................................................................... 9
2.6.1 (Optional) Activate/Deactivate Week Program ........................................................................ 9
2.6.2 (Optional) Selecting Heating and/or Cooling mode ................................................................ 10
2.7 Edit Operating Instructions ........................................................................................................... 11
2.7.1 Change Pre-Defined Set-Point Temperature .......................................................................... 11
2.7.2 (Optional) Edit Week Program Timer ..................................................................................... 13
2.7.3 (Optional) Edit humidity Set-point ......................................................................................... 15
2.7.4 (Optional) Edit/Set Current Time and Date ............................................................................ 16
2.7.5 (Optional) Edit/Set Monthly clock correction factor ............................................................... 18
xComfort Room Controller Touch User Manual 0v17_EN iv | P a g e
xComfort Room Controller Touch User Manual 0v17_EN 1 | P a g e
1. Introduction
1.1 Safety instructions This document contains important warnings and safety instructions which must be observed and
followed by the users. Failure to follow these warnings and safety instructions will put the fault-free
operation of the Room Controller Touch at risk.
1.2 Intended use The Room Controller Touch has been designed solely for residential use in private homes and small
offices. It is not suitable for industrial use.
The Room Controller Touch is designed to facilitate the climate control in a room and provide the user
access to this through an intuitive LCD Touch screen menu.
The Room controller can operate in two application modes:
• Control mode; in which the Room Controller Touch controls the regulation of the climate in a room
• Sensor mode; in which the Room Controller Touch registers the room climate conditions and the
user settings and sends them to an intelligent device, e.g. xComfort Smart Home Controller (SHC),
which actually controls the climate in the room.
Since the transmission of radio signals is based on a non-exclusive communication channel,
interference to the transmission are possible. Because of this, the Room Controller Touch
must not be used to control components with safety-related functions, such as
overheating protection, emergency stop or emergency call.
The use of the unit for any purpose other than described in this document or the failure to observe the
warnings and safety instructions it contains will immediately invalidate any claims in respect to the
warranty and/or liability.
1.3 Instructions for disposal Do not dispose of this device with regular domestic waste.
Electronic equipment must be disposed of at local collection points for waste electronic
equipment and in compliance with the local regulations governing waste electrical and electronic
equipment.
1.4 About this document These operating instructions are intended for end users and describe the operation and menu structure
of the Room Controller Touch.
Certain functions and their availability depend on the configuration of the Room Controller Touch during
the installation. These functions are marked with (Optional).
Please contact a suitable qualified electrical engineer for all assembly, installation and
basic configuration requirements or if you need to remove or dispose of the device.
Faulty installation or configuration can otherwise cause damage to property and persons.
xComfort Room Controller Touch User Manual 0v17_EN 2 | P a g e
2 The Room Controller Touch
2.1 Operation The Room Controller Touch is equipped with a Display with Backlight and Touch function. The display is
used to display the information through which, by touching the display, the Room Controller Touch can
be operated.
Note: The display is designed to respond to on-screen pressing only. Compared to the commonly
used touch displays for smartphones and tablets it may be the case that touching the
display a little more firmly is necessary.
In the Idle-state the display shows the temperature and status with the backlight switched off. On
touching the display it enters the Active-state. In this state, the backlight is switched on, and when
connected to the xComfort SHC, the information is refreshed to get the latest status.
Note: To maximize the battery life, a delay between the information on the display in the idle-
state and the actual status in the xComfort SHC is possible. The maximum possible delay
can be reduced by the installer, but this will lead to a reduction in the battery life. In other
configurations the display always contains the latest information.
Pre-defined temperature set-points
Frost protection
Night / Standby
Economy
Day / Comfort
Request status
Heating request
Cooling request
Ventilation request
Shown information selection
Temperature
Humidity
Clock
Outdoor temperature
Various
Units of the shown information
Setting
Touch-button
Floor temperature regulation active
Low battery indication
Week program timer
Week program timer activity status
Day of Week
Program timer switch time-point
xComfort Room Controller Touch User Manual 0v17_EN 3 | P a g e
2.2 Cleaning mode To prevent unwanted changes during the cleaning of the Room Controller Touch, the display can be put
into the cleaning mode.
The Room Controller Touch must only cleaned with glass cleaner or window cleaner, and
never with abrasive products
During the cleaning mode, the Room Controller Touch will ignore any touching on the display. The
display shows the remaining time in seconds until the Room Controller Touch switches back to normal
operation mode.
2.3 Replacing the batteries The Room Controller Touch operates with 2x LR03 (AAA) batteries which are located in the rear section
of the Room Controller.
Replace the batteries when the low battery indicator is shown on the display.
Note: Optionally, the Room Controller can also be used with an external mains power adapter. In
this case batteries are not required. Contact your installer for more information.
Do NOT press the center of the display to mount!! For the correct mounting, with two
hands, simply press the outer frame of the Room Controller Touch.
Used batteries should not be disposed of with regular domestic waste. They should be
taken to a battery disposal point.
Never recharge standard batteries!! This entails a risk of explosion.
Do not throw the batteries into fires
Do not short-circuit batteries
>10 Sec.
xComfort Room Controller Touch User Manual 0v17_EN 4 | P a g e
2.4 Operation mode The operation functions of the Room Controller Touch are grouped into the following:
• Frequently used operation functions, Basic operation functions.
• Occasionally used operation functions, Enhanced operation functions
• Changes to the settings, Edit operation functions
Note: To start operating the Room Controller Touch, touching the screen once is necessary to
activate the display.
To maximize the battery life, the Room Controller Touch display will enter the Idle-state. In this state,
the display shows the temperature and status with the backlight switched off. On touching the display
again it enters the Active-state. In this state, the backlight is switched on, and when connected to the
xComfort SHC, the information is refreshed to get the latest status.
2.4.1 Basic operations
• Show the current temperature
• Temporary adjust the current set-point temperature
• Show the current set-point temperature
• Select (another) per-defined set-point temperature (operation mode)
• Show the current humidity
• (Optional) Show outdoor temperature
• (Optional) Show time and Day of Week
• (Optional) Touch-button(s)
2.4.2 Enhanced operations
• Select regulation mode; Heating, Cooling, (Optional) Heating&Cooling or OFF mode
• (Optional) Switch Week Program Timer ON or OFF
2.4.3 Settings edit operations
• Edit pre-defined Set-point temperatures
• (Optional) Edit Week Program
• (Optional) Edit Humidity Set-point
• (Optional) Edit Time and Date
• (Optional) Edit clock correction factor
xComfort Room Controller Touch User Manual 0v17_EN 5 | P a g e
2.5 Basic Operating Instructions
2.5.1 Show Current Room Temperature
The default screen on the display shows the current temperature. After a timeout, the Room Controller
will always return to this default screen. It is also possible to manually select the default ‘current
temperature screen’.
2.5.2 Show Current/Active Set-Point Temperature
The set-point temperature which currently is used for the regulation of the temperature in the room can
be shown.
Note: The active set-point temperature is the sum total of the active pre-defined operation mode
set-point temperature and the temporary adjustment (increase or decrease) that is made.
Initial
Step 1
(Optional)
Select the Heating or
Cooling set-point
Idle
Timeout
xComfort Room Controller Touch User Manual 0v17_EN 6 | P a g e
2.5.3 Temporarily adjust the current set-point temperature
It is possible to temporarily increase or decrease the current set-point temperature. The temporary
increase or decrease in the set-point temperature will be reset to zero when the operation mode (pre-
defined set-point temperature) is changed, either manually or via the Week Program Timer.
Note: To change the set-point temperature permanently, see the following section: ‘Edit
Operating Instructions - Change Pre-Defined Temperature Set-point’.
Initial
Step 1
Optional Selection of
Heating or Cooling set-
point
Step 2
Idle
Timeout
2.5.4 Switch active set-point temperature (operation mode)
The Room Controller Touch supports four different pre-defined and reprogrammable set-point
temperatures (operation modes) for an easy change in the desired (set-point) temperature during the
day. It is possible to manually switch between these pre-defined set-point temperatures.
The pre-defined set-points can also be used in the Week Program (when enabled) to switch
automatically between the different set-point temperatures on a timed basis,
Note: The Week Program will be switched OFF when the active set-point temperature (operation
mode) is changed manually.
xComfort Room Controller Touch User Manual 0v17_EN 7 | P a g e
Initial
Step 1
Step 2
Idle
Timeout
2.5.5 Show Room Humidity
The Room Controller Touch also measures the humidity in the room, and the humidity can be displayed
by selecting the display humidity screen.
2.5.6 (Optional) Show outdoor temperature.
Sensor mode
This option is available when the Room Controller is connected to an intelligent device which provides
the outdoor temperature.
Control mode
The option is available in control mode if, during installation, the external temperature sensor input is
configured for use as an outdoor temperature sensor.
xComfort Room Controller Touch User Manual 0v17_EN 8 | P a g e
2.5.7 (Optional) Show Time and Day of Week
Optionally, the current time can be displayed. The option is available in both the sensor mode and the
control mode if the Week Program Timer is enabled during the installation.
2.5.8 (Optional) Touch-button(s)
The Touch-buttons of the Room Controller Touch can be used as push buttons to control the lights,
shutters/blinds in the room, for example, or to trigger Scenes in the xComfort SHC.
Note: To get the Touch-buttons, an actuator or intelligent device must be connected to the
Touch-button of the Room Controller during the installation. Contact your installer for
more information.
The Room Controller Touch has up to two Touch-buttons . Their behavior depends on the
configuration during the installation:
• 2x Single Pushbuttons: Each Touch-button is connected individually to an actuator(s) or to an
intelligent device (e.g. the xComfort SHC). The Touch-button acts as single pole pushbutton.
The Touch-button supports short pressing (e.g. switch on/off) and long pressing (e.g. dimming
up/down).
• 2x Single Rocker with arrow keys: Each Touch-button is individually connected to an actuator(s)
or to an intelligent device (e.g. xComfort SHC).
When the Touch-button is pressed it will start flashing, and the arrow keys are shown, which can
be used ‘up ‘ or ‘down’. In this respect on the ‘up’ key, apply a short press to switch on and a
long press to dim up. Press briefly on the ‘down’ key to switch off or to dim down.
• 1 Single Rocker: Both Touch-buttons are connected to the same actuator(s). The pair of Touch-
buttons behave as one 2 pole pushbutton. The Touch-button on the left is the ON/UP
(short/long press) part and on the right the OFF/DOWN part.
xComfort Room Controller Touch User Manual 0v17_EN 9 | P a g e
2.6 Enhanced Operating Instructions
2.6.1 (Optional) Activate/Deactivate Week Program
The Week Program can be optionally deactivated (OFF) or activated (ON). When it is OFF, it is only
possible to manually switch between the pre-defined set-point temperatures (operation mode), and
when it is ON, the operation mode is based on the programmed week program.
Control mode
If the Week Program Timer function is enabled during the installation (MRF), the option to activate or
deactivate the Week Program is available in the control mode only.
Sensor mode
In the Sensor mode the option is available when connected with the xComfort SHC (e.g. Room Manager),
otherwise the Week Program is not available.
Note: If the Week Program is activated (ON), then the operation mode will switch to the correct
operation mode according to the week program for the current time.
Optional
Step 1
Step 2
Step 3 Timeout
Deactivated (OFF) Activated (ON)
xComfort Room Controller Touch User Manual 0v17_EN 10 | P a g e
2.6.2 (Optional) Selecting Heating and/or Cooling mode
It is possible to select which temperature regulation mode should be active manually.
(OFF) No icons displayed. No heating or cooling, e.g. regulation switch off.
Heating mode. Regulation based on heating set-point(s) temperature only.
Cooling mode. Regulation based on cooling set-point(s) temperature only.
Heating&Cooling mode. Regulation based on both heating and cooling set-points
temperature.
Sensor Mode
If the Room Controller is connected to an xComfort SHC, it is possible to change manually between
‘heating’, ‘cooling’ and ‘OFF’. In this case, the ‘Heating&Cooling’ mode is not available. When connected
to a Room Manager the temperature regulation mode cannot be changed.
Control Mode
* The available regulation modes depend on the configuration. If a heating or a cooling actuator is
connected only, then it is only possible to switch between ‘heating and OFF’ / ‘cooling and OFF’
manually. If both actuators are connected, then all modes are available.
Optional
Step 1
(Show mode)
Current active mode is shown
Step 2
(Select mode)
Control Mode*
(OFF)
Sensor Mode
(OFF)
Optional
Timeout
xComfort Room Controller Touch User Manual 0v17_EN 11 | P a g e
2.7 Edit Operating Instructions
2.7.1 Change Pre-Defined Set-Point Temperature
The Room Controller Touch supports up to 2 x 4 (4 for heating and 4 for cooling) different pre-defined
set-point temperatures (operation modes) which can be manually (re-)programmed via the screen.
Frost protection mode. Factory default values 10°C/32°C (or -5K with Room Manager)
Standby or Night mode. Factory default values 18°C/28°C (or -0,5K with Room Manager)
Economy mode. Factory default values 19°C/26°C (or -1K with Room Manager)
Comfort or Day mode. Factory default value 21°C/24°C (or 0K with Room Manager)
Sensor mode
When connected to the xComfort SHC, the values of the pre-defined temperature are the same as the
set-point temperatures in the SHC. Making a manual change on the Room Controller Touch will also
change the set-point in the SHC (and v.v.).
When connected to a Room Manager, the predefined temperatures are used as offset in the Room
Manager for the Room Manager’s current set-point temperature.
Control mode
The initial values used in controller mode are programmed during the installation (MRF). The set-point
values are used by the Room Controller Touch for the climate control.
Note: If the ‘Heating&Cooling’ mode is active, the Room Controller will maintain a minimum
temperature difference between the heating set-point and cooling set-point temperature
(dead zone) to prevent the continuous switching between heating and cooling. This dead
zone value can be configured during installation. The factory default is 3K.
Optional
Step 1
xComfort Room Controller Touch User Manual 0v17_EN 12 | P a g e
Enter Edit mode
Step 2
(Select Edit)
Edit icon flashing
Enter Edit Set-point temperature
Re
pe
at
th
is f
or
oth
er
set-
po
ints
wh
en
re
qu
ire
d Optional
Select the Set-point
Optional
Select the Heating or
Cooling Set-point
Step 3
(Change)
Changed value is flashing
Leave Edit mode
Step 4
Timeout or
Idle Timeout
xComfort Room Controller Touch User Manual 0v17_EN 13 | P a g e
2.7.2 (Optional) Edit Week Program Timer
Sensor mode
When connected to an intelligent device, the climate control is carried out by the intelligent device and
based on the Week Program programmed in the intelligent device. Changes to the Week Program should
therefore be made in the intelligent device.
Control mode
In the control mode, the Week Program Timer is available if it is enabled during the installation (MRF).
The Room Controller Touch supports up to 6 manually (re-)programmable points for each Day of Week
at which time the Room Controller Touch should switch the active set-point temperature (operation
mode), and to which of pre-defined set-point temperatures (operation mode) it should switch.
Step 1
Step 2
Enter Edit mode
Step 3
(Select Edit)
Edit icon flashing
Step 4
(Enter Program edit)
The Day of week and Trigger point
are flashing
Enter Edit Program
Re
pe
at
this
Select Day of Week
Selected is flashing:
- The Day of the Week or
- Midweek: (Mo +…+ Fr) or
- Weekend: ( Sa + Su)
xComfort Room Controller Touch User Manual 0v17_EN 14 | P a g e
Select Switch point
Selected Switch point is flashing
To change the pre-defined set-point
Change Pre defined
Set-point
Selected Set-point has an underscore
To Change the Time minutes
Change Time
minutes
Step 1
(Select)
Minutes are flashing
Step 2 (Change)
To Change the Time hours
Change Time Hour
Step 1 (Select)
Hours are flashing
Step 2 (Change)
xComfort Room Controller Touch User Manual 0v17_EN 15 | P a g e
Leave Edit mode
Step 6
(Leave Edit mode)
Timeout or
Idle
Timeout
2.7.3 (Optional) Edit humidity Set-point
Sensor mode
The Humidity set-point is not available if the Room Controller is connected to an intelligent device, e.g.
SHC or Room Manager.
Control mode
This option is available in control mode if a humidity actuator is connected to the Room Controller Touch
during the installation. The Room Controller Touch will send an OFF command to the actuator if the
humidity is above the set-point value, and it will send an ON command if the actual humidity is below
the set-point value. The set-point value can be changed manually.
Initial select Humidity
Edit mode
Enter
Change
xComfort Room Controller Touch User Manual 0v17_EN 16 | P a g e
Leave Timeout or
2.7.4 (Optional) Edit/Set Current Time and Date
Sensor Mode
The option to set the Time and Date manually with the Room Controller is not available if the Room
Controller is connected to an xComfort SHC. In this case, the time and date are synchronized with the
xComfort SHC date and time.
Control Mode
The Time (Hours, Minutes) and Date (Day of Week, Day of Month, Month and Year) can be set manually
if the Week Program is enabled during installation.
Attention:
The time and date are used for the execution of the Week Program. The Time and Date
need to be set correctly for the correct operation of the Week Program
Initial select Clock
Enter Edit Mode
xComfort Room Controller Touch User Manual 0v17_EN 17 | P a g e
Select Item and change
Re
pe
at
this
ste
p f
or
ea
ch
ite
ms
th
at
ne
ed
s to
be
ch
an
ge
d
Select
Number (1-6) is flashing
Hours
Minutes
Day of Week
Day of Month
Month
Year
Change
Use the arrow-keys to
change
When changed the changed numbers
starts flashing
Leave Edit Mode Timeout or
xComfort Room Controller Touch User Manual 0v17_EN 18 | P a g e
2.7.5 (Optional) Edit/Set Monthly clock correction factor
Any inaccuracy to the Room Controller Touch internal clock can be corrected by configuring the number
of seconds that the clock needs to be corrected by each month (-99 to +99 seconds).
Note: The accuracy of each clock may vary slightly, which can make the clock go out of sync with
the current time. This results in the Week Program switching to the desired set-point
temperature too early or too late.
The option is only available if the clock function is enabled during the installation and if the Room
Controller does not receive the time and date from another device.
Initial select clock
Enter Edit Press Edit > 5 Sec
Change
Leave Edit
xComfort Room Controller Touch User Manual 0v17_EN 19 | P a g e
xComfort Room Controller Touch User Manual 0v17_EN 20 | P a g e
© Eaton Industries (Austria)
Eugenia 1
3943 Schrems
Austria
www.xcomfort.com
www.eaton.eu/xcomfort