Post on 04-Jun-2018
transcript
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
1/25
PROPOSAL FOR STUDENT INNOVATIVE
PROJECTSTITLE :
AN ALL TERRAIN,NEGATIVE PRESSURE CUM
MAGNETIC ADSORPTION WALL CLIMBING
ROBOT FOR INSPECTION AND CRACKDETECTION
BY,
R.JA I KARTHIK 2011507025
A .GERAD AMBROSE 2011507016
G.VENKATAKRISHNAN 2011507054
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
2/25
UNDER THE GUIDANCE OF
Dr.R.Sivaramakris hnanAssociate Professo r,
Department of
ProductionTechnology,
Anna University,
MIT Campus.
Mr.M.Thirumalazhagan
Assistant Professor,
Department of
Production Technology,Anna University,
MIT Campus.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
3/25
OBJECTIVE OF THE
PROJECT : The traversing and
inspection of large vertical
and over-head surfaces
with autonomous systems
is still an unsolved
problem.
In this project, we aim to
achieve a prototype of a
wall-climbing robot which
works on the principles of
negative pressureadsorption and magnetic
adhesion.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
4/25
Why this project ???
As the main principles for this wall-climbing robotcomprise of magnetic adso rpt ionand under-pressure adhesion, concepts like ROBOTICSand PNEUMATICS, which are some of ourdepartments many areas of expertise, are
covered. Also, if fortunately, this project gets selected and
progresses smoothly till stage II, then we alsohave an option of using this robot for inspection,again where NON-DESTRUCTIVE-TESTING
TECHNIQUES : another important part in ourdepartments curriculum, will be covered.
Also, the areas of application of this particularproject, of which BOILER INSPECTION plays amajor part, are also very much related to ourdepartment.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
5/25
Scenario so far
WHY DO WE NEED CLIMBING ROBOTS??
Climbing robots are mainly adopted in places wheredirect access by a human operator is very expensive,because of the need for scaffolding, or if its very
dangerous, due to the presence of an hostileenvironment.
WHAT DO WE EXPECT FROM THESE ROBOTS??
These robots should be capable of travelling overdifferent types of surfaces, with different inclinations,such as floors, walls, ceilings, and to walk betweensuch surfaces.
Regarding the adhesion to the surface, the robotsshould be able to produce a secure gripping forceusing a light-weightmechanism.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
6/25
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
7/25
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
8/25
A wall climbing robot should, not only be light, but also havelarge payload, so that it may reduce excessive adhesionforces and carry instrumentations during navigation.
Up to now a lot of research has been devoted to wall-
climbing robots and various types of experimental modelswere already proposed.
The major two issues in the design of wall climbing robots istheir locomotion and adhesion methods.
With respect to the locomotion type, three types are oftenconsidered :
Crawler typeWheeled type
Legged type
According to the adhesion method, these robots aregenerally classified into three groups :
Magnetic adhesionNegative pressure adhesion
Gripping mechanism using claws or spikes
Electro-adhesive mechanism
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
9/25
Electro-adhesion is still a technology that hasnot really been understood and is still at thefirst stage of development. Prototypes of
robots incorporating this principle exist, e.g.Daltorio2005 (sticky robot), Rochat2011(Thermal glue robot), but have not made itbig in the market due to the high costinvolved and maintenance issues.
In case of clamping and grippingmechanism-based robots, the surfacestructure is very critical. These robots, e.g.Spenko2008, BretI2004, etc. depend heavilyon the nature of the surface. There is alwaysa very high risk involved here as theprobability of the robot falling off from the
wall-surface is very high.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
10/25
Thermal gluerobot [Rochat2011]
Sticky robot
[Daltorio2005]
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
11/25
Robot rise[Spenko200
8]
Ape-like lemur
[Bretl2004]
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
12/25
The Current Scenario
Thus, there is a huge demand for a wall-climbingrobot which is:
1. Light
2. Fast3. Robust enough to carry payloads
4. Able to traverse inclinations and multi-terrains.
5. In case of boilers, we should be able to carry outthe inspection during the run-time itself.
So, this is where our project comes into picture.
In this project, we aim to create such a robot thatcan meet the above pre-requisites.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
13/25
Possible applications of thisrobot are inspection ofexternal/internal surface ofaboveground/underground
petrochemical storage tanks,boilers, concrete walls,metallic structures and so on.
In petrochemical storagetanks, due to the extremelycorrosive petroleum that thetanks may contain, it is veryimportant to perform periodicinspection at different rates
In boilers, regular inspectionis an important factor here to
ensure the safety andreliability of these structuresthroughout the year. Anynonchalance can lead to lossof life in huge numbers.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
14/25
Also with theimplementation ofthe Metro Rail
system in Chennai(CMRL) in the nearfuture, these robotscan also be used to
traverse the longconcrete pillarssupporting the over-head rail lines andinspect them for
cracks, etc. as that isa very critical areawhose safety cannotbe compromised.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
15/25
PRINCIPLE(S):
This robot works on the basis of two main principles/theories :
MAGNETIC ADHESION
UNDER-PRESSURE ADSORPTION
MAGNETIC ADHESION technique includeselectromagnets as well as permanent magnets, whichare either positioned on the surface or kept with acertain distance away from it. Common applications of
these systems are inspections, maintenance andconstruction work e. g. of high power poles, steeltanks, boilers or ship hulls. The principle is veryreliable on ferromagnetic surfaces and it is able tocreate strong adhesion forces on a very small area.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
16/25
NEGATIVE PRESSUREADSORPTION techniquecan be distinguished
between three differenttypes: Passive suctioncups, active suctionchambers and a vortex
system. The vortex system
generates adhesiveforces via a vortex insideof the robot. This vortexis created by a high-speed rotor and allowsadhesion withoutadditional sealing
elements as needed bythe cu -based s stems.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
17/25
HOW THE ROBOT WORKS :
The robot will look like any another all-terrain robot. The robot will have magnetic tracks around its
wheels, which will enable it to traverse acrossferromagnetic surfaces.
The tracks will wind around the wheels like a loop
and help them to adhere onto the surface below. Thus, by using those tracks, we incorporate the
concept of MAGNETIC ADHESION.
We then include the principle of NEGATIVEPRESSURE ADSORPTION by fashioning a vacuumengine out of a fan rotating at a high speed, fixed atthe centre of the robot in an enclosure.
The CENTRIFUGE fan, which is actuated by anexternal motor, rotates at a very high speed andcreates a VORTEX in the gap between it and thesurface below.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
18/25
This vortex will cause asuction-effect (low pressurearea) thereby creating avacuum-region and enablingthe robot to stick to the terrain.
The wheels on the sides of therobot will help in thelocomotion of the robot.
While traversing onferromagnetic surfaces, usageof the vacuum engine is notnecessary, as the magnetic
tracks by themselves willenable adhesion.
The wheels will rotate by thehelp of motors fixed on thebase of the robot.
Thus, this is a WHEELED-DRIVE, MAGNETICADHESION, NEGATIVEPRESSURE ADSORPTIONbased climbing robot.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
19/25
APLLICATIONS
Our robot can traverse vertically ,horizontally aswell as overhead surfaces making it ideal for usein inspection of
1. Boilers
2. Pipe inspection in chemical systems3. Ship cleaning/inspection (in dry dock)
4. Airplane cleaning and inspection
5. Nuclear plant inspection
6. Steel bridge inspection
7. Cleaning and inspection of glass wall
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
20/25
STANDOUT PROPERTIES
So what will make this robot to stand out from its earlier counter-parts?
This robot, for starters, is a HYBRIDbecause we incorporate both the
concepts of magnetic adhesion and vortex mechanism.
This model will be less bulky, and hence, fast.
Compared to normal suction cups, let them be active or passive, this is a better
option because :
I. It uses vortex mechanism, so no need of a bulky vacuum pump
II. No need for any sealing mechanism, only some amount of clearance is
enough
III. As theres no pump on-board, the pay-load carrying capacity of the robot
increases.
IV. The absence of vacuum pump ensures elimination of excessive powerconsumption and hence ENERGY CONSERVATION
V. Simple structure ensures that it is cheaper, lighter, fasterand more
effective.
There are only a very few robots out in the industry that incorporate vortex
mechanism for adhesion, and even less which use the combination of two
adhesion techniques. Further more, in our country, this concept so far is almost new. Thus there is
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
21/25
FUTURE SCOPE
If this project succeeds in itsmain objective, i.e. wall-climbing, then in the next stageof the project, we canimplement NON-DESTRUCTIVE TESTING
techniques and tailor the robotso that it detects cracks, andother surface defects.
Sensors can be fitted on therobot so that it senses anypossible cracks on the terrainand relays its coordinates tothe controller below.
If possible, we can also attemptto make the whole robotwireless and mount the batterytoo on it.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
22/25
DURATION OF THE
PROJECTACTIONDURATION
Literature Survey -3 weeks
Development of robot prototype -3 weeks
Incorporation of under pressureadhesion and magnetic adsorption -4
weeks
Development of non-destructive
technique to be employed -
4weeks Fabrication -6 weeks
Testing -4 weeks
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
23/25
COSTS :
ITEMS COST(IN RUPEES)
1) MATERIALS/ COMPONENTS/ FABRICATION
a) Design and fabrication of mechanical
componentsb) Electrical components and accessories
c) Vehicle prototype and accessories
9250
92502500
TRAVEL 1000
CONTINGENCIES 2500
TOTAL 24500
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
24/25
CONCLUSION :
A real-time prototype of an all-terrain,negative pressure cum magnetic
adsorption based robot for navigation over
horizontal, vertical and overhead surfaces
irrespective of their materialistic nature andalso for surface-inspection will be delivered
at the end of the stipulated time.
8/13/2019 wall climbing robot - magnetic adhesion and negative adsorption-combined
25/25