Post on 01-Feb-2018
transcript
HOFFMAN INSTRUMENTATION SUPPLY6110 Northwest Croeni Road
Hillsboro, Oregon 97124
phone 800.466.4906fax 503.466.2164
www.hisoregon.com
Important Notice:
The product data in this catalog were obtained under specific test conditions that may vary substantially from actual site conditions and/or customer needs. Purchasers or other end-users of HIS products must rely solely on their system design and engineers when selecting HIS products for a particular system, and when determining the suitability of any system in which any HIS products are to be installed.
HIS shall bear no liability as to product selection criteria or decisions. HIS shall not be liable for any product that has been damaged, including direct, special or consequential damages (including but not limited to lost profits or income). HIS shall also not be liable for misuse, improper handling, improper service or products modified by anyone other than HIS.
Dimensions:
Measurements used in this publication are given in inches. Every attempt has been made to ensure the accuracy of the information contained in this publication. HIS is not to be held liable in any manner for any mistakes, omissions typographical and/or printing er-rors. Dimensions are subject to change without notice.
H I S , I n c .Since its inception in 1979, HIS has developed into an internationally recognized manufacturer of high quality vacuum components and fittings. We are pleased to supply major end-users, mechanical contractors, universities and original equipment manufacturers.
Our commitment to customer service includes:
• large inventory
• competitive prices
• in-house manufacturing
• quick turnaround
• superior surface finishes
The personal pride of HIS employees has resulted in a contin-ued history of customer satisfaction. We plan to continue and improve our competitive edge as a premium supplier.
W e l d F i t t i n g s a n d T u b i n gMATERIAL
HIS products conform to ASTM and ASME standards.304/304L grade is the standard, but 316/316L is available upon request.
TEST REPORTS
Material test reports will be furnished upon request at the time of order.
FINISH
Standard finish for fittings is Mill Finish; other finishes available upon request.
Standard finish for tubing is Bright and Annealed; other finishes available upon request.
TYPICAL PART NUMBER
WF-18-45EL-304-TIMFinish
M=Mill Finish StandardWeld Fitting 5= Number 5 polish OD
7= Number 7 polish OD/IDP= Electro Polish
WALL THICKNESS
Thickness may vary by the allowable limits of the ASTM/ASME standards.All measurements in inches unless otherwise noted.
800.466.4906 • www.hisoregon.com �
WELDING
All welding is done with cryogenic source inert gas welding methods. HIS uses ASME qualified welders and ASME procedures designed to provide the best possible welds. Automatic or semi-automatic positioning fixtures are used on tubing and fittings. Interior surfaces are smooth, even and uniform.
TUBE
HIS tubing conforms to ASTM A-269, A-262 Practice “E” requirements unless otherwise specified.
FITTINGS
Our fittings conform to ASTM A269 and A270 and can be supplied in 304/304L or 316/316L. Fittings come with a standard mill finish. Other finishes available: mechanical polish ID/OD (#7), mechanical polish OD (#5), and electropolished ID.
MARKING
Special marking as required by customer is available.
PACKAGING
All tube, fittings, and fabrications will be properly packaged. Special packag-ing as required by customer is available.
QUALITY
The HIS quality program incorporates non-destructive and destructive testing, statistical process control, and operator auditing on products. We welcome on-site inspections or surveys by your company prior to shipment.
HOFFMAN INSTRUMENTATION SUPPLY� HOFFMAN INSTRUMENTATION SUPPLY�
45° elbow, type �A
A
90° elbow, type �
Part no. Tube Size AWF-12-90EL-304-T1 3/4 1.125WF-16-90EL-304-T1 1 1.500WF-18-90EL-304-T1 1 1/2 2.250WF-20-90EL-304-T1 2 3.000WF-25-90EL-304-T1 2 1/2 3.750WF-30-90EL-304-T1 3 4.500WF-40-90EL-304-T1 4 6.000WF-60-90EL-304-T1 6 9.000
Part no. Tube Size AWF-12-45EL-304-T1 3/4 0.469WF-16-45EL-304-T1 1 0.625WF-18-45EL-304-T1 1 1/2 0.938WF-20-45EL-304-T1 2 1.25WF-25-45EL-304-T1 2 1/2 1.563WF-30-45EL-304-T1 3 1.875WF-40-45EL-304-T1 4 2.5WF-60-45EL-304-T1 6 3.75
800.466.4906 • www.hisoregon.comAll measurements in inches unless otherwise noted.
WELD
FITTINGS&
TUBIN
G
�800.466.4906 • www.hisoregon.comAll measurements in inches unless otherwise noted.
45° elbow with tangents, type �
Part no. Tube Size AWF-12-45EL-304-T2 3/4 2.250WF-16-45EL-304-T2 1 1.188WF-18-45EL-304-T2 1 1/2 1.625WF-20-45EL-304-T2 2 2.313WF-25-45EL-304-T2 2 1/2 3.000WF-30-45EL-304-T2 3 3.688WF-40-45EL-304-T2 4 4.813
90° elbow with tangents, type �
A
Part no. Tube Size AWF-12-90EL-304-T2 3/4 3.000WF-16-90EL-304-T2 1 2.063WF-18-90EL-304-T2 1 1/2 2.938WF-20-90EL-304-T2 2 4.063WF-25-90EL-304-T2 2 1/2 5.188WF-30-90EL-304-T2 3 6.313WF-40-90EL-304-T2 4 8.313
A
HOFFMAN INSTRUMENTATION SUPPLY4
45° elbow with extended tangents, type �
Part no. Tube Size AWF-12-45EL-316-T3 3/4 2.250WF-16-45EL-316-T3 1 2.250WF-18-45EL-316-T3 1 1/2 3.000WF-20-45EL-316-T3 2 3.250WF-25-45EL-316-T3 2 1/2 3.625WF-30-45EL-316-T3 3 3.688WF-40-45EL-316-T3 4 4.813
90° elbow with extended tangents, type �
Part no. Tube Size AWF-12-90EL-316-T3 3/4 3.000WF-16-90EL-316-T3 1 3.000WF-18-90EL-316-T3 1 1/2 4.500WF-20-90EL-316-T3 2 5.750WF-25-90EL-316-T3 2 1/2 5.188WF-30-90EL-316-T3 3 6.313WF-40-90EL-316-T3 4 8.313
A
A
800.466.4906 • www.hisoregon.comAll measurements in inches unless otherwise noted.
WELD
FITTINGS&
TUBIN
G
5
90° mitered elbow
Part no. Tube Size AWF-12-90EL-MTR-T1 3/4 1.000WF-16-90EL-MTR-T1 1 1.880WF-18-90EL-MTR-T1 1 1/2 2.250WF-18-90EL-MTR-T2 1 1/2 2.410WF-20-90EL-MTR-T1 2 3.000WF-20-90EL-MTR-T2 2 2.610WF-25-90EL-MTR-T1 2 1/2 3.000WF-25-90EL-MTR-T2 2 1/2 3.750WF-30-90EL-MTR-T1 3 3.250WF-30-90EL-MTR-T2 3 3.880WF-40-90EL-MTR-T1 4 4.870WF-40-90EL-MTR-T2 4 4.250WF-60-90EL-MTR-T1 6 5.000WF-60-90EL-MTR-T2 6 6.060
Custom lengths available upon request.
A
HOFFMAN INSTRUMENTATION SUPPLY6
concentric reducer, type �
Part no. Tube Size AWF-12-08RC-304-T1 3/4 x 1/2 1.000WF-16-08RC-304-T1 1 x 1/2 1.500WF-16-12RC-304-T1 1 x 3/4 1.000WF-18-08RC-304-T1 1 1/2 x 1/2 3.500WF-18-12RC-304-T1 1 1/2 x 3/4 3.000WF-18-16RC-304-T1 1 1/2 x 1 2.000WF-20-16RC-304-T1 2 x 1 4.000WF-20-18RC-304-T1 2 x 1 1/2 2.000WF-25-18RC-304-T1 2 1/2 x 1 1/2 4.000WF-25-20RC-304-T1 2 1/2 x 2 2.000WF-30-18RC-304-T1 3 x 1 1/2 6.000WF-30-20RC-304-T1 3 x 2 4.000WF-30-25RC-304-T1 3 x 2 1/2 2.000WF-40-18RC-304-T1 4 x 1 1/2 10.000WF-40-20RC-304-T1 4 x 2 8.000WF-40-25RC-304-T1 4 x 2 1/2 6.000WF-40-30RC-304-T1 4 x 3 4.000WF-60-30RC-304-T1 6 x 3 6.000WF-60-40RC-304-T1 6 x 4 4.000
A
800.466.4906 • www.hisoregon.comAll measurements in inches unless otherwise noted.
WELD
FITTINGS&
TUBIN
G
�
concentric reducer, type 4
Part no. Tube Size AWF-16-12RC-304-T4 1 x 3/4 2.375WF-18-16RC-304-T4 1 1/2 x 1 2.375WF-20-16RC-304-T4 2 x 1 2.375WF-20-18RC-304-T4 2 x 1 1/2 2.375WF-25-18RC-304-T4 2 1/2 x 1 1/2 2.375WF-25-20RC-304-T4 2 1/2 x 2 2.375WF-30-18RC-304-T4 3 x 1 1/2 3.625WF-30-20RC-304-T4 3 x 2 3.625WF-30-25RC-304-T4 3 x 2 1/2 3.625WF-40-18RC-304-T4 4 x 1 1/2 5.500WF-40-20RC-304-T4 4 x 2 3.625WF-40-25RC-304-T4 4 x 2 1/2 3.625WF-40-30RC-304-T4 4 x 3 3.625WF-60-30RC-304-T4 6 x 3 5.500
A
WF-60-40RC-304-T4 6 x 4 5.500
HOFFMAN INSTRUMENTATION SUPPLY8
tee
Part no. Tube Size A BWF-12-12TE-304-T1 3/4 1.875 3.75WF-16-16TE-304-T1 1 1.875 3.75WF-18-18TE-304-T1 1 1/2 2.250 4.5WF-20-20TE-304-T1 2 3.000 6WF-25-25TE-304-T1 2 1/2 3.000 6WF-30-30TE-304-T1 3 3.250 6.5WF-40-40TE-304-T1 4 3.875 7.75WF-60-60TE-304-T1 6 5.000 10
A
A
B
800.466.4906 • www.hisoregon.comAll measurements in inches unless otherwise noted.
WELD
FITTINGS&
TUBIN
G
9
reducing tee
Part no. Tube Size A B CWF-16-12RT-304-T1 1 x 3/4 2.125 3.750 1.875WF-18-12RT-304-T1 1 1/2 x 3/4 2.250 4.500 2.250WF-18-16RT-304-T1 1 1/2 x 1 2.375 4.500 2.250WF-20-12RT-304-T1 2 x 3/4 2.375 6.000 3.000WF-20-16RT-304-T1 2 x 1 2.375 6.000 3.000WF-20-18RT-304-T1 2 x 1 1/2 2.500 6.000 3.000WF-25-18RT-304-T1 2 1/2 x 1 1/2 2.750 6.000 3.000WF-25-20RT-304-T1 2 1/2 x 2 3.250 6.000 3.000WF-30-18RT-304-T1 3 x 1 1/2 3.000 6.500 3.250WF-30-20RT-304-T1 3 x 2 3.500 6.500 3.250WF-30-25RT-304-T1 3 x 2 1/2 3.250 6.500 3.250WF-40-20RT-304-T1 4 x 2 4.000 7.750 3.875WF-40-25RT-304-T1 4 x 2 1/2 3.750 7.750 3.875WF-40-30RT-304-T1 4 x 3 3.750 7.750 3.875WF-60-30RT-304-T1 6 x 3 4.750 10.000 5.000WF-60-40RT-304-T1 6 x 4 4.875 10.000 5.000
Custom sizes available upon request.
A
B
C
HOFFMAN INSTRUMENTATION SUPPLY�0
4-way cross
Part no. Tube Size AWF-12-12CS-304-T1 3/4 1.875WF-16-16CS-304-T1 1 1.875WF-18-18CS-304-T1 1 1/2 2.250WF-20-20CS-304-T1 2 3.000WF-25-25CS-304-T1 2 1/2 3.000WF-30-30CS-304-T1 3 3.250WF-40-40CS-304-T1 4 3.875WF-60-60CS-304-T1 6 5.000
A
800.466.4906 • www.hisoregon.comAll measurements in inches unless otherwise noted.
WELD
FITTINGS&
TUBIN
G
��
4-way reducing cross
Part no. Tube Size A Tube Size B C DWF-16-12CS-304-T1 1 3/4 1.880 1.120WF-18-12CS-304-T1 1 1/2 3/4 2.250 1.380WF-18-16CS-304-T1 1 1/2 1 2.250 2.130WF-20-12CS-304-T1 2 3/4 3.000 1.630WF-20-18CS-304-T1 2 1 1/2 3.000 2.500WF-25-18CS-304-T1 2 1/2 1 1/2 3.000 2.750WF-25-20CS-304-T1 2 1/2 2 3.000 3.250WF-30-18CS-304-T1 3 1 1/2 3.250 3.000WF-40-18CS-304-T1 4 1 1/2 3.880 3.500WF-40-20CS-304-T1 4 2 3.880 4.000WF-40-25CS-304-T1 4 2 1/2 3.880 3.750WF-40-30CS-304-T1 4 3 3.880 3.750WF-60-18CS-304-T1 6 1 1/2 5.000 4.500WF-60-20CS-304-T1 6 2 5.000 5.000WF-60-25CS-304-T1 6 2 1/2 5.000 4.750WF-60-30CS-304-T1 6 3 5.000 4.750WF-60-40CS-304-T1 6 4 5.000 4.880
C
D
Tube B
Tube A
HOFFMAN INSTRUMENTATION SUPPLY��
5-way cross
Part no. Tube Size AWF-12-12CS-304-5WY 3/4 1.000WF-16-16CS-304-5WY 1 1.880WF-18-18CS-304-5WY 1 1/2 2.250WF-20-20CS-304-5WY 2 3.000WF-25-25CS-304-5WY 2 1/2 3.000WF-30-30CS-304-5WY 3 3.250WF-40-40CS-304-5WY 4 3.880WF-60-60CS-304-5WY 6 5.000
6-way cross
A
Part no. Tube Size AWF-12-12CS-304-6WY 3/4 1.000WF-16-16CS-304-6WY 1 1.880WF-18-18CS-304-6WY 1 1/2 2.250WF-20-20CS-304-6WY 2 3.000WF-25-25CS-304-6WY 2 1/2 3.000WF-30-30CS-304-6WY 3 3.250WF-40-40CS-304-6WY 4 3.880WF-60-60CS-304-6WY 6 5.000
A
800.466.4906 • www.hisoregon.comAll measurements in inches unless otherwise noted.
WELD
FITTINGS&
TUBIN
G
��
weld cap, type �
Part no. Tube Size AWF-12-12WC-304-T1 3/4 .313WF-16-16WC-304-T1 1 .469WF-18-18WC-304-T1 1 1/2 .594WF-20-20WC-304-T1 2 .781WF-25-25WC-304-T1 2 1/2 1.063WF-30-30WC-304-T1 3 1.094WF-40-40WC-304-T1 4 1.281WF-60-60WC-304-T1 6 2.125
A
HOFFMAN INSTRUMENTATION SUPPLY�4
Hoffman Instrumentation Supply provides stainless steel tubing conforming to ASTM specifications SA249, A249, A269, A262, A262 Practice “E,” A270. Tubing can be supplied in 304/304L and 316/316L. Standard tube finish is bright annealed. Other finishes available upon request: mechanical polish ID/OD (#7), me-chanical polish OD with bright annealed ID (#5), and electropolished ID.
Tube OD Surface Finish Wall1/2 bright annealed .0493/4 bright annealed .0651 bright annealed .0651 1/2 bright annealed .0652 bright annealed .0652 1/2 bright annealed .0653 bright annealed .0654 bright annealed .0836 bright annealed .1091 polished ID & OD 0.0652 polished ID & OD 0.0652 1/2 polished ID & OD 0.0653 polished ID & OD 0.0654 polished ID & OD 0.0836 polished ID & OD 0.109
stainless steel tubing
Other sizes, wall thicknesses and polishes available upon request.