Post on 29-Jun-2020
transcript
series
16t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Straight & folding sliding door system for commercial interior & exterior applications up to 440kg
Runners Series 50 includes a wide range of accessories for sliding and folding doors used for different types of application either residential or industrial. The carrying capacity of the rail and the accessories make this series particularly suitable for the construction of different types of greenhouses, stables and barns, and for the construction of sliding covers and folding garage doors.
Runners Series 50 is designed for commercial and agricultural applications such as warehousing, agricultural buildings, stables etc. The comprehensive range of hangers and components allows Series 50 to be used for many applications including overhead runway systems, partitions, sliding curtains and stabling blocks. Series 50 maximum panel weight capacity is 440kg*.*capacity based on 2 x 220kg hangers per panel.
Wheel Types
Reliability
38mm ball bearing wheels with hardened steel tyre and stainless steel bearings.
series
17t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Track
Straight sliding components
Straight sliding systems for timber or metal doors
Brackets:Face fixing
Brackets:Soffit fixing Connector
Hangers
Suspension Plates Guide channel Track Stops
Accessories:
Series 50 straight sliding systems are suitable for timber or metal doors with a maximum panel weight up to 440kg when using two 220kg 4 wheel hangers per door. Capacity will be reduced accordingly if using lower capacity hangers from the Series 50 range. Components suitable for use with straight sliding systems are detailed below. Generally two hangers are used on each door panel. A third or fourth hanger can be used to increase door weight capacity. eg. using three 50-53 hangers would allow a door panel weighing up to 660kg to be used.
When using upper track support brackets they should be fixed at a minimum of 600mm and a maximum of 1000mm spacing. Series 50 steel or aluminium upper track is NOT pre-drilled and will require drilling for soffit fixing. Our Technical Team are available on 01280 822288 to help you with system configuration and hardware selection if required.
Track
Track stopHanger
Suspension plate
Bracket
Guide channel
Bottom guide
Typical panel configurations
Single track run
Double track run
TECHNICAL ADVICEConsult our Technical Team on 01280 822288 for help with hardware configuration and quantities.
See page 23 for full range details.
series
series
50-50
50-59
50-52
50-61
50-65
50-62 50-63 50-76 50-1297
50-57 50-1257 50-60 50-74 50-55
50-53 50-53A 50-1272 50-1273 50-78 50-79 50-600 50-603 50-1368
50-58 50-1293A50-59DOUBLE
50-590
Bottom Guides
18t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Face Fixing
Double Track
Sliding application examples
For face fixing use double bracket 50-59DOUBLE
See bottom guide options on page 19
See bottom guide options on page 19
Soffit Fixing
See bottom guide options on page 19
50-59DOUBLE
Technical
50-59
50-50(950)
50-50(950)
50-60
50-53(52)
50-53(52)
50-57
40 min70 max
40 min70 max
30
30
Ø16
Ø16
52 min65 max
50-55
50-55
35 min/42 max
50-50(950)50-58
50-1257
50-1272(1273)
85 min115 max
With canopy (see page 43)
30Ø20
46 min
50-55
series
19t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Face Fixing
Face Fixing
Sliding application examples
Steel Doors
Steel Doors
See bottom guide options on page 19
See bottom guide options on page 19
Bottom Guide Options A B C
A. Guide roller fixed to floor with under guide channel recessed into door bottom.B. Screw mounted guide roller fixed to door with under guide channel recessed into floor.C. Guide channel fitted to door bottom with guide roller fixed to floor.D. Double doors configurations are easily installed using double runs of under guide channel 50-74 and suitable guides.E. Bottom guide 50-76 used with angle steel, which can also act as a weather strip.F. T-section metal bar fitted to door underside and used with bottom guide 50-76.
50-62(63)50-7430
Metal door
50-62(63)50-74
8
50-62(63)50-74
50-768
Other bottom guide options available. See GUIDE ROLLER section on page 25
Metal doorD E F
30 min
5 max5 max
50-76
Typical bottom guide configurations for sliding systems (suggestions only).
Technical
20 min
100
50-59
50-59
50-50(950)
50-50(950)
50-53A
50-53(52)
Ø14 hole
Ø14 hole
26 max
26 max
50-55
50-55
50-62(63)
50-74
8
24.6
45 min
20 min
20t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
End Folding Systems
Centre Folding SystemsSeries 50 centre folding systems are suitable for timber or metal doors with a maximum panel weight up to 440kg when using two 220kg 4 wheel hangers per door. Capacity will be reduced accordingly if using lower capacity hangers from the Series 50 range. Components suitable for use with centre folding systems are detailed below. Our Technical Team are available on 01280 822288 to help you with system configuration and hardware selection if required.
Series 50 end folding systems are suitable for timber or metal doors with a maximum panel weight up to 440kg when using two 220kg 4 wheel hangers per door. Capacity will be reduced accordingly if using lower capacity hang-ers from the Series 50 range. Components suitable for use with end folding systems are detailed below. Our Technical Team are available on 01280 822288 to help you with system configuration and hardware selection if required.
End Folding door components
Centre Folding door components
Centre folding/end folding systems for timber or metal doors
series
series
Track
Rotating Suspension plate
Guide channel
Bottom guide
Track
Rotating Hanger
Guide channel
Bottom guide
series
Track Brackets:Face fixing
Brackets:Soffit fixing Connector
Hangers
Suspension Plates Guide channel Track Stops
Accessories:
See page 23 for full range details
50-50
50-59
50-52
50-62 50-63 50-1297
50-57 50-1257 50-60 50-74 50-55
50-1272 50-1273
50-78 50-79
50-58 50-1293A50-59DOUBLE
50-590
Bottom Guides
50-53A
50-53
Track Brackets:Face fixing
Brackets:Soffit fixing Connector
Hangers
Suspension Plates Guide channel Track Stops
Accessories:
See page 23 for full range details
50-50
50-59
50-52
50-61
50-6550-62 50-1297
50-74 50-55
50-1272 50-1273
50-78 50-79
50-58 50-1293A50-59DOUBLE
50-590
Bottom Guides
50-53A
50-53
Rotating Hanger
series
21t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
NOTE: The width of the door panel which is hinged to the frame (jamb) must be reduced by half the thickness of the door plus 23mm, plus the diameter of the hinge knuckle when using butt hinges.The example below is for a hinge with a 14mm knuckle. Dimension will vary depending on hinge choice.
Example using 60mm thick door.
60mm ÷ 2 = 30mm
30mm + 23mm + 14mm
= 67mm reduction in width.
Other typical centre folding panel configurationsAll panels equal width except jamb leaf which must be reduced as shown above.
Other typical panel end folding configurationsAll panels equal width except jamb leaf which must be reduced as shown above.
Typical plan of 3 1/2 doors
Typical plan of 3 1/2 doors
Hinged at jamb
Hinged at jamb
Hinged at jamb
Hinged at jamb
Access panel
Access panel
TECHNICAL ADVICEConsult our Technical Team on 01280 822288 for help with hardware configuration and quantities.
Allow clearance for hinge knuckles when
using butt hinges
Allow clearance for hinge knuckles when
using butt hinges
Hinged at jamb
Hinged at jamb
Technical
NOTE: The width of the door panel which is hinged to the frame (jamb) must be reduced by half the thickness of the door plus half the width of the remaining doors, plus the diameter of the hinge knuckle when using butt hinges.The example below is for a hinge with a 14mm knuckle. Dimension will vary depending on hinge choice.
Example using 1000mm wide x 60mm thick door.
1000mm ÷ 2 = 500mm; 60mm ÷ 2 = 30mm;
500mm + 30mm + 14mm
= 544mm reduction in width.
End Folding
50-59
50-59
50-50(950)
50-52(53)
50-61
50-61
50-6550-74
50-53 50-52
50-61
26 min50 max
113
41
30
113
19
20
4
4
10 min35 max
90
40 min
Ø16
40
Processing of door for 50-61
See bottom guide options on page 22
22t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Folding application examples
Centre Folding
50-50(950)
50-57
50-52(53)
50-5350-52
50-57Pin alignment
40 min70 max
35
Ø16
40 min
50-129750-74
See bottom guide options on page 22
Typical bottom guide configurations for folding systems (suggestions only).
A. Guide roller fixed to floor with under guide channel recessed into door bottom.B. Guide roller fixed to door with under guide channel recessed into floor.C. When using suspension plate 50-61 it is recommended to also use bottom guide 50-65D. Guide roller fixed to floor with under guide channel fitted to door bottom (metal door).
TECHNICAL ADVICEConsult our Technical Team on 01280 822288 for help with hard-ware configuration and quantities.
Bottom Guide Options
Other bottom guide options available. See GUIDE ROLLER section on page 25.
A B C
50-62(63)50-7430
Metal door
50-62(63)
50-52(53)
50-74
850-62(63)
50-74
8
24.6
D
Technical
series
23t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Tracks & Guides
50-50
50-950
50-74
Galvanised steel upper track
Aluminium upper track
Under guide galvanised steel channel
48
48
24.6
21
25.5
4848
Length Part No.
1 metre 50-50-12 metre 50-50-23 metre 50-50-34 metre 50-50-45 metre 50-50-5
Length Part No.
1 metre 50-590-12 metre 50-590-23 metre 50-590-34 metre 50-590-45 metre 50-590-5
Length Part No.
1 metre 50-74-12 metre 50-74-23 metre 50-74-34 metre 50-74-45 metre 50-74-5
50-1293A
Track connector for upper track
Actual Size
Actual Size
Actual Size
2.0
4.0
Steel upper track is available bent by special order to a specific radius.i
Aluminium upper track is available bent by special order to a specific radius.i
Under guide channel is available bent by special order to a specific radius.i
All steel track and guide channels are supplied in galvanised finish. Regular greasing is required to prevent premature wear from friction.i
24t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Wheel Types
50-52
50-1273
50-603 50-600
50-53A
50-53
50-1272
50-52 | 160kg capacity 50-1272 | 110kg capacity
50-1273 | 160kg capacity
50-53A | 220kg capacity
50-78 | 160kg capacity
50-603 | 160kg capacity
50-1368 | 160kg capacity
50-600 | 160kg capacity
50-79 | 220kg capacity
Adjustable steel roller with M12 x 60mm pin and 38mm ball bearing wheels.
Adjustable steel roller with M12 x 100mm pin and 38mm ball bearing wheels.
As 50-53A but with 60mm pin
Adjustable steel roller with M16 x 60mm pin and 38mm ball bearing steel wheels.
Adjustable steel roller with M16 x 60mm pin and 38mm ball bearing steel wheels.
Adjustable steel roller with M12 x 78mm rotating pin and 38mm ball bearing wheels.
Steel roller with 38mm ball bearing wheels.
Steel roller with 38mm ball bearing wheels. 38mm ball bearing wheels with hardened steel tyre and stainless steel bearings.
Steel roller with 38mm ball bearing wheels.
Adjustable steel roller with M12 x 78mm rotating pin and 38mm ball bearing wheels.
38mm ball bearing steel wheels. 38mm ball bearing steel wheels.
38mm ball bearing steel wheels.
38mm ball bearing steel wheels.
38mm ball bearing steel wheels.
38mm ball bearing steel wheels.
38mm ball bearing steel wheels.
38mm ball bearing steel wheels.
38mm ball bearing steel wheels.
115
155
115
60 100
60
69 69
78 78
80
60
50
70
50-78 50-79
70
100
30
63
122
160kg
160kg
160kg
210kg
220kg
220kg
160kg
160kg
110kg
80
60
50-136863
Hanger wheel technical information
39.0
29.7520.5
38
series
Hangers
series
Please note that when using upper track support brackets it is recommended that they should be fixed at 600mm - 1000mm spacing. i25
t. 01280 822288 f. 01280 813024 e. sales@runners-sales.com w. www.runners-uk.com
Guide rollers/brackets/plates
50-65
50-62 50-63 50-1297
50-5550-1297
50-58
50-61
50-65 Steel side guide roller with rotating brass pin 20mm diameter.Minimum door thickness 40 mm.
50-1297 Rotating brass pin 20mm diameter.
For resin fix guide rollers suitable for concrete floorssee page 39
50-62 Steel guide roller with rotating brass pin 20mm diameter.
50-55 Door stop for the upper track.
50-63 Steel guide roller with rotating brass pin 20mm diameter.
50-1297 Rotating brass pin 20mm diameter.
140
40
103 39
39
72
7272
Gap5.5
39
50-57 Steel rotating suspension plate for M12 pin.Min. door thickness 32mm.For use with: 50-52; 50-53; 50-78; 50-79
50-60 Steel rotating suspension plate for M12 pin.Min. door thickness 52mm. Max 65mmFor use with: 50-52; 50-53; 50-78; 50-79
50-1257 Steel rotating suspension plate for M16 pin.Min. door thickness 46mm.For use with: 50-1272; 50-1273
50-61 Steel rotating suspension plate for M12 pin.Min. door thickness 40mm.For use with: 50-52; 50-53; 50-78; 50-79
50-58 Ceiling fixing steel bracket for the upper track.
50-59 Wall fixing steel bracket for the upper track.
50-59 DOUBLE Twin track wall fixing steel bracket for the upper track. Maximum spacing adjustment 30mm
120 140
111
61
58.558.5
50
50
57
100
100
40
103
10 14.5
31.5 45 70
105
5250-57 50-1257
50-59
50-60
60
59
59
30 max
59140
50-59DOUBLE
Track will require drilling to accept
M8 boltiTrack will require drilling to accept
M8 bolti
Requires 4 x M6 cup square bolts
to suit. (Not included)
i
Ø12.810
18
Ø12.8