Post on 12-Mar-2018
transcript
Page 3 – 5 Wire CablePage 6 – 7 Kwik-LocsPage 8 – 9 Kwik-Loc KitsPage 10 – 14 Suspension AccessoriesPage 15 Tools and SuppliesPage 16 Hanging at AnglesPage 17 – 19 Kwik-Loc Applications & SpecificationsPage 20 Suspension BracketsPage 21 – 31 Ceiling Suspension Kits
Page 23 TurnbucklesPage 24 Threaded RodPage 25 Tube SpacersPage 26 – 29 Nuts, Bolts & WashersPage 30 Suspension Hooks & PlatesPage 31 Mushroom Caps
Contents
SolutionS For trADE
www.crh.com.au
www.crh.com.au 3SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
KWIK-LOC cable locks and galvanised Cable are the fast & versatile way to hang static loads. Studies have shown installation time can be reduced up to 6 times compared to traditional installs using threaded rod, chain, hanger straps or other cable systems.All KWIK-LOC cable locks incorporate a length of pre-cut cable with a swaged end loop for maximum speed, efficiency and safety.
This light weight system is a major safety improvement in terms of handling and installing on site and reduces OH&S problems when installing in aerial situations when compared to heavy traditional fittings.
KWIC-LOK cable locks and galvanised wire rope are available in numerous configurations forattachment to virtually any type of building structure.
Features & Benefits
www.crh.com.au 4SolutionS For trADE
Wire cable & suspension systems
Wire Cable
CableGalvanized steel cable supplied by CRH is manufactured to exact standards and statistically tested to verify the breaking strength. Using cable supplied by CRH ensures the safety and integrity of the hanging system.
Cable RollsGalvanized steel cable supplied by the roll.
Looped CableLooped Cable enhances the KWIK-LOC suspensionsystem by the addition of a pre-looped end. Once the wireCable is pulled around the anchor point and through thelooped end of the cable, it is already secured at one end,saving time at the job site. The remaining wire Cable, “thedrop”, is passed through a channel in the KWIK-LOC.
Then the wire Cable is inserted through a fastening point and back up into the second channel of the same cable lock. The locking teeth inside the cable lock engage the wire Cable which secures the equipment in place. The tensioning tool completes the adjustment.
* Ask CRH for our most recent cable Batch break weight test certificates
Item name
Gal Steel Cable - 2.5mm (3/32”) 30381 2.5mm (3/32”) +.012 / -.006” 7 x 7 152.4mGal Steel Cable - 3.2mm (1/8”) 30382 3.2mm (1/8”) +.014 / -.007” 7 x 7 152.4mGal Steel Cable - 4.8mm (3/16”) 30383 4.8mm (3/16”) +.018 / -.009” 7 x 19 76.2m
CoDe CabLe DIameteR toLeRanCe ConstRuCtIon RoLL sIZe
www.crh.com.au 5SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Looped Cable
RLC4.8-1 4.8mm (3/16) x 1 metre looped Cable.RLC4.8-2 4.8mm (3/16) x 2 metre looped Cable.RLC4.8-3 4.8mm (3/16) x 3 metre looped Cable.RLC4.8-4 4.8mm (3/16) x 4 metre looped Cable.RLC4.8-5 4.8mm (3/16) x 5 metre looped Cable.RLC4.8-6 4.8mm (3/16) x 6 metre looped Cable.RLC4.8-7 4.8mm (3/16) x 7 metre looped Cable.RLC4.8-8 4.8mm (3/16) x 8 metre looped Cable.RLC4.8-9 4.8mm (3/16) x 9 metre looped Cable.RLC4.8-10 4.8mm (3/16) x 10 metre looped Cable.
stoCK CoDe DesCRIPtIon
Note: Looped cable enhances the KWIK-LOC suspension system by the addition of a pre-looped end. Once the wire is pulled around the anchor point and through the looped end of the cable, it is already secured at one end, saving time at the jobsite.
www.crh.com.au 6SolutionS For trADE
Wire cable & suspension systems
KWIK-LOCS
Zinc HousingOne piece die cast Zinc alloy combines major anti-corrosion properties with strength and consistent manufacturing quality.
Locking WedgesAn oil impregnated sintered steel locking wedge is seated in each of two channels. Both wedges incorporate a release pin for easy adjustment. Each wedge makes contact with the cable using serrated teeth. These teeth press onto the cable and spread the load across the length of the wedge, maximizing grip strength.
stainless steel springsEach spring is manufactured of stainless steel and assures initial engagement of the locking wedge to the wire rope.
Pull adjustment pin back and Pass WIRe through Kwik-Loc™
Loop WIRe through anchor
Pull adjustment pin back and Pass WIRe back through Kwik-Loc™
always Confirm engagement of Kwik-Loc™on wire before applying load
to adjust, take the load off and pull the tail slightly to disengage teeth, then release using adjustment pin
www.crh.com.au 7SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
KWIK-LOCS
30350 KL200 is the largest of the Kwik-Loc series highest safe work load limit. Ceiling Suspension 4.8mm 290kg 362kg
The KL200 is perfect for hanging sound systems, heavy cable trays, Systems, Heavy (3/16”)
suspended, ceilings etc. Cable Trays,
Sound Systems 3.2mm 113kg 141kg
30004 KL200 Kwik-Loc - Pack of 10 (1/8”)
030055 The KL150 is significantly smaller in size and with a lower safe work Heavy Cable 3.2mm 102kg 127kg
(Pack of 4) load limit than the KL200. The KL150 can be used to hang Heavy Cable Baskets, (1/8”)
Baskets Lighting & Signs. Fencing & vine supports Lighting, Signs,
Fencing 2.5mm 68kg 85kg
030003 KL150 Kwik-Loc - Pack of 25 (3/32”)
030056 The KL100 was introduced to work on most light hanging applications, Cable Trays, Ducting, 2.5mm 68kg 85kg
(Pack of 4) Cable, Trays, Ducting, Signs, Evaporators, to name a few Evaporators, Signs, (1/8”)
Lighting
030002 KL100 Kwik-Loc - Pack of 10
CoDe DesCRIPtIon tyPICaL aPPLICatIonsWIRe RoPeDIameteR
safe WoRKIng LoaD@ 5:1 safety faCtoR
safe WoRKIng LoaD@ 4:1 safety faCtoR
The easy adjustment system.
no tooLs ReQuIReD!
www.crh.com.au 8SolutionS For trADE
Wire cable & suspension systems
CoDe DesCRIPtIon safe WoRKIng LoaD at 5:1.
Looped Cable & KWIK-LOC Kits
KL200-1M-4.8 1m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-2M-4.8 2m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-3M-4.8 3m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-4M-4.8 4m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-5M-4.8 5m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-6M-4.8 6m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-7M-4.8 7m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-8M-4.8 8m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-9M-4.8 9m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kgKL200-10M-4.8 10m x 4.8mm Looped Cable & KL200 Kwik-Loc 290kg 30130 1.5m x 3.2mm Looped Cable & KL150 Kwik-Loc 120kg30131 4.5m x 3.2mm Looped Cable & KL150 Kwik-Loc 120kg30132 7.6m x 3.2mm Looped Cable & KL150 Kwik-Loc 120kg 30128 1.5m x 2.5mm Looped Cable & KL150 Kwik-Loc 68kg30129 4.5m x 2.5mm Looped Cable & KL150 Kwik-Loc 68kg30133 6.1m x 2.5mm Looped Cable & KL150 Kwik-Loc 68kg
www.crh.com.au 9SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
safe WoRKIng LoaD at 5:1.CoDe mateRIaL DesCRIPtIon
30020 2.5mm Galvanised 1 x Y configuration 2m drop with Snap Hooks & KL150 Kwik-Loc. 700mm Legs, 68kg(Pack of 2) Steel Cable A Snap Hook system can be used for clipping onto cable baskets & trays.
30186 2.5mm Galvanised Y configuration 1.5m drop with Snap Hooks & KL150 Kwik-Loc. 450mm Legs. 68kg(Pack of 2) Steel Cable
30192 2.5mm Galvanised Y configuration 3m drop with Snap Hooks & KL150 Kwik-Loc. 450mm Legs. 68kg(Pack of 2) Steel Cable
30266 2.5mm Galvanised Y configuration 4.5m drop with Snap Hooks & KL150 Kwik-Loc. 450mm Legs. 68kg(Pack of 2) Steel Cable
KL150 with y snap HooksSimply Loop the end of the cable through your fixing point & secure with the KL150 KWIK-LOC.
example shown : code 030020
KWIK-LOC Kits
Fuse Cut
Cable
Snap Hook
www.crh.com.au 10SolutionS For trADE
Wire cable & suspension systems
Suspension Accessories
Zip-Clip
CoDe mateRIaL
30040 Zinc Alloy 2.5mm (3/32”) Zip-Clips are suitable for use with single or multi-tiered trapeze systems and in applications supporting such items as 3.2mm (1/8”) cable trays, baskets, water and gas pipes and chilled beams.
The Zip-Clip cable lock combined with cable and uni-strut is an efficient method of constructing a support structure. The Zip-Clip fits inside uni-sturt and has a spring loaded pawl which allows entry and passage of cable through the cable lock. Once engaged by the pawl, the cable is gripped with increasing pressure as the suspended load is increased. To ease adjustment each Zip-Clip cable lock has an integrated release pin to disengage the gripping pawl. To insure the integrity of the suspension system use cable supplied by CRH Australia.
Pack of 4 Features: •AWorkLoadlimitof220lbs(100kg) •Builtin5:1safetyfactor •Fitsinsidestrut
suItabLe CabLe sIZe DesCRIPtIon
www.crh.com.au 11SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Suspension Accessories
CoDe mateRIaL DesCRIPtIon
30298 Zinc Alloy The KV bracket enhances the Rize Kwik-Loc suspension system by the addition of an integral bracket, which fastens the cable lock to the duct with sheet metal screws. Once the KV bracket is attached to the equipment, the wire rope “drop” is passed into the entry hole at the top of the bracket, through the cable lock, and out the exit hole at the bottom. The locking teeth inside the cable lock engage the wire rope and secure the ductwork in place. The KV100 Bracket assembly has a working load limit of up to 68kg. Suitable for 2.5mm (3/32”) Wire. Pack of 4.
30296 Zinc Plated Low Carbon Steel Eye Bolt & Nut with 3/8” thread. Thread length 38mm. Working load 65kg. Pack of 4
KV100 bracketHelps stabilize cable on sharp corners
eye bolt & nut
www.crh.com.au 12SolutionS For trADE
Wire cable & suspension systems
Corner ProtectorsHelps stabilize cable on sharp corners
Hanger PlatesZinc Plated 45˚ Hanger Plate
CoDe mateRIaL DesCRIPtIon
HP45K Galvanised Steel Hanger Plate.
Pack of 4
30086 Nylon Corner Protectors help to stabilise cable on sharp corners.
Pack of 4
www.crh.com.au 13SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Suspension Accessories
Con-Lock
CoDe DesCRIPtIon
30174 Suspension systems typically use threaded rod with washers and nuts to construct a support structure. Sizing, cutting and assembling the rods to the complementary
parts and fastening them to an anchor point can be very time consuming.
The Con-Lock system is designed for the suspension of all static loads into all concrete types including slagged, cracked, slab and even hollow pot. The Con-Lock is
designed to use a ¼” or 6 mm drill bit. Then tapped into place with a standard hammer, no claw back of the anchor is needed for installation. There is no need for any
other tools.
With a working load limit of 100lbs or 50kgs the con-Lock can be used for most electrical installations.
Pack of 4
www.crh.com.au 14SolutionS For trADE
Wire cable & suspension systems
ConcreteWoodSteel
foR use In sCReW sIZe
PRoDuCt Range
PILot HoLe statIC LoaD CaP
5/16” x 1-1/2”1/4” x 2” 1/4” x 2”
1/4”NoneNone
72kg90kg90kg
CoDe DesCRIPtIon
30138 50mm Vertical Fastener for Concrete 30293 50mm Horizontal Fastener for Concrete 30139 50mm Vertical Fastener for Wood 30294 50mm Horizontal Fastener for Wood 30295 50mm Vertical Fastener for Steel 30140 50mm Horizontal Fastener for Steel
Kwik-twistWhen preparing to suspend equipment, ductwork or accessories, threaded anchor points are often required. Kwik-Twists from Rize are side or vertical mounted fasteners that provide attachment points for steel threaded rods and other assemblies. There are three variations of Kwik-Twists; one for penetrating and threading into steel, one for wood, and one for concrete. Each Kwik-Twist has a 3/8”-16 threaded hole in the fastener’s hex shaped head. Side mounted Kwik-Twists have the threaded hole perpendicular to the fastener shaft and passing completely through the fastener head. Vertical mounted Kwik-Twists have the threaded hole parallel to the fastener shaft and as deep as the fastener head.
• NopilotholeisneededforwoodorsteelKwik-Twists;a1/4”pilotholeisrequiredforconcrete• Allfastenersarezincplatedforcorrosionresistance• Packaged4PerPack.
Suspension Accessories
www.crh.com.au 15SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Tools and Supplies
CoDe DesCRIPtIon
30340 Rize Wire Cutters
Wire Cutters Rize tensioning tool
CoDe DesCRIPtIon
30341 As in all aspects of construction there may be timeswhen you need to put a little more tension on the cable than is possible with just your hands. Therefore, Rize has available a tensioning tool for these applications. Made of steel and meant to last, the tensioning tool takes all sizes of Kwik-Locs and up to 3/16 inch cable. As with all Rize products the tensioning tool is guaranteed against initial quality defects. Natural wear and tear on the tool is eventually going to happen. Rize therefore keeps ample stocks of replacement parts available when needed.
• Thetensioningtoolisdesignedtoapplytensionofupto600lbsoncable that is terminated by a Kwik-Loc.
• ThetensioningtoolworksbyholdingtheKwik-Locbodyandpullingthe cable through the Kwik-Loc using the cam and anvil.
• The powerful lever action will tension and retension the cable inseconds.
• ThetensioningtoolcanbeusedonallsizesofKwik-Locs.
www.crh.com.au 16SolutionS For trADE
Wire cable & suspension systems
CabLe sIZe VeRtICaL 15° 30° 45° 60°
4.8mm (3/16”) 290 kg 280 kg 250 kg 205 kg 145 kg
3.2mm (1/8”) 43 kg 108 kg 97 kg 79 kg 55 kg
2.5mm (3/32”) 68 kg 65 kg 58 kg 47 kg 34 kg
Load 100% 96% 86% 70% 50%
Hanging at Angles
KWIK-LOCS can be used to suspend objects safely at angles up to 60 degrees from vertical.However, suspension at angles does reduce the safe working load per the table below.
Pull adjustment pin back and Pass WIRe through Kwik-Loc™
Loop WIRe through anchor
Pull adjustment pin back and Pass WIRe back through Kwik-Loc™
always Confirm engagement of Kwik-Loc™ on wire before applying load
to adjust, take the load off and pull the ta il slightly to disengage teeth, then release using adjustment pin
www.crh.com.au 17SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Applications
LightingThe Kwik-Loc is ideally designed for the installation of all types of lights, from HID’s to fluorescents and Cinematic flood lights. It is the fastest and easiest way to install and adjust all of your lighting suspension requirements.
electricalElectrical systems are being designed to minimize installation time. Typical examples are snap together busbar and basket tray systems. Kwik-Locs help carry on generating time and cost saving through to the end of the hanger installation process.
Typical electrical applications include – Busbar, cable ladder, cable tray, cable basket, channel, trunking, lighting rafts, luminaries, secondary supports, safety lines, high wattage lights, electrical cables, cctv cameras and sound systems.
www.crh.com.au 18SolutionS For trADE
Wire cable & suspension systems
Applications
Retail & signageCRH supplies a variety of products both sold individually and in kits that lend themselves perfectly for use hanging signage. Due to the small size, the Kwik-Loc blends well in both retail and signage industries where appearance is a large factor.
mechanicalMany mechanical installations lend themselves to being supported using Kwik-Locs. The hangers can be directly fixed onto the services or used to suspend dedicated support systems. A tailor-made solution service available to devise specific solutions for a project.
Typical mechanical applications include – Water pipes, drainage pipes, gas pipes, chill beams, ceiling heating panels and radiant heaters.
DuctworkKwik-Locs are compliant with the recommendations laid down in DW/144 and Smacna. In most cases by actually wrapping the cable around the duct itself, huge savings in materials and time can be made. The result is a reduction in the number of split ring brackets and bearers used and a corresponding increase in productivity. Whether it is hanging a fan coil unit or ductwork, Kwik- Locs offer the right solution.
Typical HVAC applications include – Spiral ducting, oval ducting, rectangular ducting, fan coil units, destratification fans and extraction ductwork.
www.crh.com.au 19SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Performance Specifications
All KWIK-LOCS have been independently tested to five times their allowable working load by one or more of the following independent laboratories:
• MELBOURNETestingServices-NATAApproved
• SMACNATesting&ResearchInsititute
• UnderwritersLaboratories
• TUVRheinland
• RADCOInc,LongBeachCA
• NewYorkTestingLaboratories
• NEL
• APAVE
All KWIK-LOCS have been tested to UL 1598 and are listed under File# E246601
Warnings• TOENSUREHANGINGSYSTEMINTEGRITYANDSAFETY,USEONLY
CRH SUPPLIED CABLE.
• DONOTUSEFORLOADSOUTSIDETHESTATEDRANGEOFTHEPRODUCT.
• DONOTEXCEEDTHESAFEWORKINGLOADOFTHEPRODUCT.
• DONOTUSEKWIK-LOCONCOATEDCABLE.
• DONOTAPPLYPAINTOROTHERCOATING.
• DONOTAPPLYLUBRICANT.
• DONOTUSEFORLIFTING.
• KEEPTHEPRODUCTCLEANANDFREEFROMDIRT.
• REMOVEANYDAMAGEDCABLEENDPRIORTOINSERTINGINTOTHE KWIKLOC.
• DONOTUSEINCHLORINATEDATMOSPHERES.
• FORDRYLOCATIONSONLY.
• FORUSEONSTATICLOADAPPLICATIONSONLY.
www.crh.com.au 20SolutionS For trADE
Wire cable & suspension systems
Ceiling Suspension Kits & Components
suspension bracket
suspension bracketssuspension bracket With thimble
CoDe mateRIaLDesCRIPtIon
A70 Suspension bracket, 120mm x 40mm. Hot Dipped Galvanized
A70T Suspension bracket With Thimble. 120mm x 40. For use with wire cable Hot Dipped Galvanized
www.crh.com.au 21SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Ceiling Suspension Kits & Components
Ceiling suspension Kit
CoDe mateRIaLDesCRIPtIon
CSK20075-M10 Ceiling Suspension Kit - M10 Thread, for 75mm panel. Designed for use with wire rope. Hot Dipped Galvanised
CSK200100-M10 Ceiling Suspension Kit - M10 Thread, for 100mm panel. Designed for use with wire rope. Hot Dipped Galvanised
CSK300150-M10 Ceiling Suspension Kit - M10 Thread, for 150mm panel. Designed for use with wire rope. Hot Dipped Galvanised
CSK20075-M12 Ceiling Suspension Kit - M12 Thread, for 75mm panel. Designed for use with wire rope. Hot Dipped Galvanised
CSK200100-M12 Ceiling Suspension Kit - M12 Thread, for 100mm panel. Designed for use with wire rope. Hot Dipped Galvanised
CSK300150-M12 Ceiling Suspension Kit - M12 Thread, for 150mm panel. Designed for use with wire rope. Hot Dipped Galvanised
www.crh.com.au 22SolutionS For trADE
Wire cable & suspension systems
Ceiling suspension Kit
Ceiling Suspension Kits & Components
CoDe mateRIaLDesCRIPtIon
CRCB10-200 Ceilingsuspensionkit.10mmthread.Suitablefor50-100mmPanel. •HotDippedGalvanised
•Nylonmushroomcap
•Whitecolour
CRCB10-300 Ceilingsuspensionkit.10mmthread.Suitablefor50-200mmPanel. •HotDippedGalvanised
•Nylonmushroomcap
•Whitecolour
CRCB12-200 Ceilingsuspensionkit.12mmthread.Suitablefor50-100mmPanel. •HotDippedGalvanised
•Nylonmushroomcap
•Whitecolour
CRCB12-300 Ceilingsuspensionkit.12mmthread.Suitablefor50-200mmPanel. •HotDippedGalvanised
•Nylonmushroomcap
•Whitecolour”
CRCBZ-10 Ceilingsuspensionkit.M10Thread.Suitablefor50-250mmPanel. •ZincPlated
•Nylonmushroomcap
•Whitecolour
www.crh.com.au 23SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Ceiling Suspension Kits & Components
turnbuckles
CoDe mateRIaLDesCRIPtIon
CRH035 Turnbuckle. M10 thread. Hot dipped galvanised
SKZ-001 Turnbuckle. M10 thread. Zinc Plated.
CRH034 Turnbuckle. M12 thread. Hot dipped galvanised
www.crh.com.au 24SolutionS For trADE
Wire cable & suspension systems
Ceiling Suspension Kits & Components
threaded Rod
CoDe mateRIaLDesCRIPtIon
CRH067-200 M10 galvanised threaded rod. 200mm Hot dipped galvanised
CRH035 M10 galvanised threaded rod. 300mm Hot dipped galvanised
SKZ-002 M10 Threaded Rod. 300mm Zinc Plated
M10-1000Z M10 Threaded Rod. 1000mm Zinc Plated
CRH060-200 M12 galvanised threaded rod. 200mm Hot dipped galvanised
CRH060-300 M12 galvanised threaded rod. 300mm Hot dipped galvanised
M12-1000Z M12 Threaded Rod. 1000mm Zinc Plated
www.crh.com.au 25SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Ceiling Suspension Kits & Components
tube spacers
CoDe mateRIaLDesCRIPtIon
CRH061-75 75mm Tube Spacer. Suitable for up to M12 Thread. PVC
CRH061-100 100mm Tube Spacer. Suitable for up to M12 Thread. PVC
CRH061-150 150mm Tube Spacer. Suitable for up to M12 Thread. PVC
www.crh.com.au 26SolutionS For trADE
Wire cable & suspension systems
nuts, bolts & Washers
Ceiling Suspension Kits & Components
CoDe mateRIaLDesCRIPtIon
CRH062 Washer. 62mm diameter x 2.7mm Hot Dipped Galvanised
SKZ-003 Washer. 62mm diameter x 2.7mm Zinc Plated
www.crh.com.au 27SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Ceiling Suspension Kits & Components
nuts, bolts & Washers
CoDe mateRIaLDesCRIPtIon
CRH065 Hex nut. M10x1.5 Hot Dipped Galvanised
SKZ-006 Hex nut. M10x1.5 Zinc Plated
CRH063 Hex nut. M12x1.5 Hot Dipped Galvanised
www.crh.com.au 28SolutionS For trADE
Wire cable & suspension systems
nuts, bolts & Washers
Ceiling Suspension Kits & Components
CoDe mateRIaLDesCRIPtIon
CRH064 Hex bolt. M10x40 Hot Dipped Galvanised
SKZ-004 Hex bolt. M10x40 Zinc Plated
www.crh.com.au 29SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
nuts, bolts & Washers
Ceiling Suspension Kits & Components
CoDe mateRIaLDesCRIPtIon
CRH066 Washer. 20x11x1.4. Material: Hot dipped galvanised. Hot Dipped Galvanised
SKZ-005 Washer. 20x11x1.4. Material: Hot dipped galvanised. Zinc Plated.
www.crh.com.au 30SolutionS For trADE
Wire cable & suspension systems
suspension Hook
Ceiling Suspension Kits & Components
200mm
50mm
Ceiling suspension Plate
CoDe mateRIaLDesCRIPtIon
CSH Ceiling suspension hook Zinc plated
CoDe mateRIaLDesCRIPtIon
CRH064 Ceiling Suspension Plate Hot dipped galvanised. 200 x 50 x 8mm
www.crh.com.au 31SolutionS For trADE
Wire Cable & SuSpenSion SyStemS
Ceiling Suspension Kits & Components
mushroom Caps
mateRIaLDesCRIPtIon
CSD-10 Mushroom Cap, M10 Thread, Surf Mist Color Nylon
CSD-12 Mushroom Cap, M12 Thread, Surf Mist Color Nylon
CoDe